The AD3530/AD3530R (8-channel) and AD3531/AD3531R (4-channel) are
low-power, 16-bit, buffered voltage output DACs with software-
programmable gain controls, providing full-scale output spans of 2.5V or
5V for reference voltages of 2.5V. These devices operate from a single
2.7V to 5.5V supply and are guaranteed monotonic by design. The "R"
variants include a 2.5V, 5ppm/°C internal reference, which is disabled
by default.
Support for monitoring internal die temperature, output voltages, and
current of a selected channel via the MUXOUT pin using an external ADC
is currently not implemented.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Kim Seer Paller <kimseer.paller@analog.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250429-togreg-v7-3-0af9c543b545@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPI offload support to stream TX buffers using DMA.
This allows loading samples to the DAC with a rate of 1 MSPS.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250207-dlech-mainline-spi-engine-offload-2-v8-17-e48a489be48c@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ROHM BD79703 is a 6 channel digital to analog converter.
Based on the data-sheet examples the hardware would support setting the
DAC word without changing the actual output. The data-sheet is not too
specific on how the enabling the output of new voltage set by DAC
should be done - hence this is not implemented by the driver.
The BD79703 would also support two specific "PULL_DOWN" modes. These
aren't currently supported by the driver either.
Add a very basic support for controlling the channel outputs one-by-one.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/bc77d7b979ca28408a216f597082fcd94ec63be7.1734608215.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add High Speed ad3552r platform driver.
The ad3552r DAC is controlled by a custom (fpga-based) DAC IP
through the current AXI backend, or similar alternative IIO backend.
Compared to the existing driver (ad3552r.c), that is a simple SPI
driver, this driver is coupled with a DAC IIO backend that finally
controls the ad3552r by a fpga-based "QSPI+DDR" interface, to reach
maximum transfer rate of 33MUPS using dma stream capabilities.
All commands involving QSPI bus read/write are delegated to the backend
through the provided APIs for bus read/write.
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20241028-wip-bl-ad3552r-axi-v0-iio-testing-v9-7-f6960b4f9719@kernel-space.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If REGMAP_SPI is n and LTC2664 is y, the following build error occurs:
riscv64-unknown-linux-gnu-ld: drivers/iio/dac/ltc2664.o: in function `ltc2664_probe':
ltc2664.c:(.text+0x714): undefined reference to `__devm_regmap_init_spi'
Select REGMAP_SPI instead of REGMAP for LTC2664 to fix it.
Fixes: 4cc2fc445d ("iio: dac: ltc2664: Add driver for LTC2664 and LTC2672")
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20241024015553.1111253-1-ruanjinjie@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver makes use of regmap_mmio, but does not select the required
module.
Add the missing 'select REGMAP_MMIO'.
Fixes: 4d4b30526e ("iio: dac: add support for stm32 DAC")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241003-ad2s1210-select-v1-8-4019453f8c33@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver makes use of regmap_spi, but does not select the required
module.
Add the missing 'select REGMAP_SPI'.
Fixes: 8316cebd1e ("iio: dac: add support for ltc1660")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241003-ad2s1210-select-v1-7-4019453f8c33@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver makes use of regmap_spi, but does not select the required
module.
Add the missing 'select REGMAP_SPI'.
Fixes: cbbb819837 ("iio: dac: ad5770r: Add AD5770R support")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241003-ad2s1210-select-v1-6-4019453f8c33@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver makes use of triggered buffers, but does not select the
required modules.
Add the missing 'select IIO_BUFFER' and 'select IIO_TRIGGERED_BUFFER'.
Fixes: 885b9790c2 ("drivers:iio:dac:ad5766.c: Add trigger buffer")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241003-iio-select-v1-8-67c0385197cd@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver makes use of triggered buffers, but does not select the
required modules.
Add the missing 'select IIO_BUFFER' and 'select IIO_TRIGGERED_BUFFER'.
Fixes: 8f2b54824b ("drivers:iio:dac: Add AD3552R driver support")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241003-iio-select-v1-7-67c0385197cd@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD8460 is a “bits in, power out” high voltage, high-power,
high-speed driver optimized for large output current (up to ±1 A)
and high slew rate (up to ±1800 V/μs) at high voltage (up to ±40 V)
into capacitive loads.
A digital engine implements user-configurable features: modes for
digital input, programmable supply current, and fault monitoring
and programmable protection settings for output current,
output voltage, and junction temperature. The AD8460 operates on
high voltage dual supplies up to ±55 V and a single low voltage
supply of 5 V.
Signed-off-by: Mariel Tinaco <Mariel.Tinaco@analog.com>
Link: https://patch.msgid.link/20240912095435.18639-3-Mariel.Tinaco@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Being this device a soft core, it's only supported on some/specific
platforms. Hence add proper dependencies for the supported platforms.
Also add COMPILE_TEST to increase the build coverage.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240604-dev-axi-dac-kconfig-v1-1-99ccd03938d1@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD9739A is a 14-bit, 2.5 GSPS high performance RF DACs that are capable
of synthesizing wideband signals from DC up to 3 GHz.
A dual-port, source synchronous, LVDS interface simplifies the digital
interface with existing FGPA/ASIC technology. On-chip controllers are used
to manage external and internal clock domain variations over temperature to
ensure reliable data transfer from the host to the DAC core.
Co-developed-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240419-iio-backend-axi-dac-v4-10-5ca45b4de294@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Support the Analog Devices Generic AXI DAC IP core. The IP core is used
for interfacing with digital-to-analog (DAC) converters that require either
a high-speed serial interface (JESD204B/C) or a source synchronous parallel
interface (LVDS/CMOS). Typically (for such devices) SPI will be used for
configuration only, while this IP core handles the streaming of data into
memory via DMA.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240419-iio-backend-axi-dac-v4-9-5ca45b4de294@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Adds driver for the MCP48xx series of DACs.
Device uses a simplex SPI channel. To set the value of an output channel,
a 16-bit data of following format must be written:
Bit field | Description
15 [MSB] | Channel selection bit
0 -> Channel A
1 -> Channel B
13 | Output Gain Selection bit
0 -> 2x Gain (Vref = 4.096V)
1 -> 1x Gain (Vref = 2.048V)
12 | Output Shutdown Control bit
0 -> Shutdown the selected channel
1 -> Active mode operation
11-0 [LSB]| DAC Input Data bits
Value's big endian representation is taken as input for the
selected DAC channel. For devices with a resolution of less
than 12-bits, only the x most significant bits are considered
where x is the resolution of the device.
Reference: Page#22 [MCP48x2 Datasheet]
Supported devices:
+---------+--------------+-------------+
| Device | Resolution | Channels |
|---------|--------------|-------------|
| MCP4801 | 8-bit | 1 |
| MCP4802 | 8-bit | 2 |
| MCP4811 | 10-bit | 1 |
| MCP4812 | 10-bit | 2 |
| MCP4821 | 12-bit | 1 |
| MCP4822 | 12-bit | 2 |
+---------+--------------+-------------+
Devices tested:
MCP4821 [12-bit single channel]
MCP4802 [8-bit dual channel]
Tested on Raspberry Pi Zero 2W
Datasheet: https://ww1.microchip.com/downloads/en/DeviceDoc/22244B.pdf #MCP48x1
Datasheet: https://ww1.microchip.com/downloads/en/DeviceDoc/20002249B.pdf #MCP48x2
Signed-off-by: Anshul Dalal <anshulusr@gmail.com>
Link: https://lore.kernel.org/r/20231220151954.154595-2-anshulusr@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
MCP4728 is a 12-bit quad channel DAC with I2C interface.
support for:
* per-channel gain
* per-channel power state
* per-channel power down mode control
* per-channel vref selection internal/vdd
* store current state to on-chip EEPROM
Signed-off-by: Andrea Collamati <andrea.collamati@gmail.com>
Link: https://lore.kernel.org/r/a0933003ed3c855f9d80d6ce0a40add2b6f0ba36.1691066050.git.andrea.collamati@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver.
Includes trivial header inclusion tidy up.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/20230311140218.74920-1-william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add initial support for DAC max5522.
Tested writing DAC A and B with some values,
from 0 to 1023, measured output voltages, driver works properly.
Additions for max5523/24/25 will follow.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Link: https://lore.kernel.org/r/20221106165928.223318-1-angelo.dureghello@timesys.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
AD5337 belongs to the same family as the AD5338.
The difference is that the AD5337 has 8-bit precision instead of 10-bit.
Add support for the AD5337 chip in the driver.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20221130182632.3856675-2-festevam@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Nothing in this driver depends on OF firmware so drop the dependency
to remove the false impression such a dependency exists.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220413190632.30365-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Nothing in this driver depends on OF firmware so drop the dependency
to remove the false impression such a dependency exists.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220413190819.38206-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Nothing in this driver depends on OF firmware so drop the dependency
to remove the false impression such a dependency exists.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220413191611.46204-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The LTC2688 is a 16 channel, 16 bit, +-15V DAC with an integrated
precision reference. It is guaranteed monotonic and has built in
rail-to-rail output buffers that can source or sink up to 20 mA.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220225130129.69-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We could probably drop a lot more of these, but for now this removes
unnecessary restrictions on stand alone ADC devices.
For these 3 drivers the false dependency seems to date all
the way back to their initial introduction.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
The AD5673R/AD5677R are low power, 16-channel, 12-/16-bit buffered voltage
output digital-to-analog converters (DACs). They include a 2.5 V internal
reference (enabled by default).
These devices are very similar to AD5674R/AD5679R, except that they
have an i2c interface.
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210217074102.23148-1-alexandru.ardelean@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD5766/AD5767 are 16-channel, 16-bit/12-bit, voltage output dense DACs
Digital-to-Analog converters.
This change adds support for these DACs.
Signed-off-by: Cristian Pop <cristian.pop@analog.com>
Link: https://lore.kernel.org/r/20210115112105.58652-3-cristian.pop@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD5338R is a 10-bit DAC with 2 outputs and an internal 2.5V
reference (enabled by default). The register configuration is nearly
identical to the AD5696R DAC that's already supported by this driver,
with the channel selection bits being the only thing different.
Signed-off-by: Michael Auchter <michael.auchter@ni.com>
Link: https://lore.kernel.org/r/20200924195215.49443-1-michael.auchter@ni.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
This patch add support for Analog Devices (Linear Technology)
LTC2634 Quad 12-/10-/8-Bit Rail-to-Rail DAC.
The SPI functionality based on them from LTC2632 therefor
add the definitions only and update the Kconfig.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
While adding a new device, I noticed these aren't sorted alphabetically [as
in the Makefile], which messed my head-up.
This change sorts the devices alphabetically in the drivers/iio/dac/Kconfig
file as well.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD5770R is a 6-channel, 14-bit resolution, low noise, programmable
current output digital-to-analog converter (DAC) for photonics control
applications.
It contains five 14-bit resolution current sourcing DAC channels and one
14-bit resolution current sourcing/sinking DAC channel.
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The only difference between LTC2632 and LTC2636 is that the former has
two DAC channels while the latter has eight.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD5600 is a single channel, 16-bit resolution, voltage output digital
to analog converter (DAC). The AD5600 uses a 3-wire SPI interface. It is
part of the AD5541 family of DACs.
The ad5446 IIO driver implements support for some of these DACs (in the
AD5441 family), so the change is a simple entry in this driver.
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/AD5600.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is a driver for Texas Instruments Dual, 12-Bit Serial Input
Digital-to-Analog Converter.
Datasheet of this chip:
http://www.ti.com/lit/ds/sbas106/sbas106.pdf
Signed-off-by: Ricardo Ribalda Delgado <ricardo@ribalda.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD5674R/AD5679R are low power, 16-channel, 12-/16-bit buffered voltage
output digital-to-analog converters (DACs). They include a 2.5 V internal
reference (enabled by default).
These devices are very similar to AD5684R/AD5686R, except that they have 16
channels.
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It is a driver for Texas Instruments 8/10/12-bit 1-channel
compatible with DAC6311 and DAC5311 chips.
Datasheet of this chip:
http://www.ti.com/lit/ds/symlink/dac7311.pdf
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
LTC1665/LTC1660 is a 8/10-bit Digital-to-Analog Converter
(DAC) with eight individual channels.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD5758 is a single channel DAC with 16-bit precision which uses the
SPI interface that operates at clock rates up to 50MHz.
The output can be configured as voltage or current and is available on a
single terminal.
Datasheet:
http://www.analog.com/media/en/technical-documentation/data-sheets/ad5758.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A nice mix this time of excellent cleanups (many to send drivers
speeding toward staging graduations) and new drivers / device support.
A good part of this is Brian Masney's never ending task on the tsl2x7x
driver. The end is in sight so hopefully we'll get that one out of
staging very soon!
New device support
* AD5686
- Support AD5685R (was wrongly present as AD5685)
- Support AD5672R, AD5676, AD5676, AD5684R and AD5686R 4 and 8 channel
SPI DACs with various precisions.
- Support AD5671R, AD5675R, AD5694, AD5694R, AD5695R, AD5696 and AD5696R
I2C DACs with various percisions and numbers of channels.
* Analog front end rescale driver - New driver.
- Support current sensing usings a shunt resistor.
- Support simple voltage dividers.
- support simple current sense amplifiers.
* TI dac5571
- New driver and device bindings supporting:
dac5571, dac6571, dac7571, dac5574, dac6574, dac7574,
dac5573, dac6573 and dac7573
* Meson-adc
- Support for Meson AXG with DT bindings.
* mpu6050
- Support the mpu9255 which only requires additional WHOAMI entry and
compatible string.
* st_lsm6dsx
- Support for lsm330dlc combinded accelerometer and gyro sensors with
DT bindings.
* stm32_adc
- Add support for STM32MP1 with bindings.
Staging graduations
* adis16201 after some excelent cleanup by Himanshu Jha.
* adis16029 after some excelent cleanup by Shreeya Patel.
New features:
* ABI docs
- Add core ABI docs for angle channels.
* inv_mpu6050
- Provide support for the full range of interrupts the device
supports.
* st_accel
- Add SMO8840 ACPI ID seen in the wild on some Lenovo machines.
* stx104
- Provide a multiple gpio get function.
Cleanups / Minor fixes
* core
- Use new nested structure support to improve kernel-doc.
* ad2s1200
- Use be16_to_cpup instead of opencoding.
* ad5686
- Indentation tidy up.
- Switch to SPDX
- Refactor to allow various numbers of channels.
- Refactor to separate core and SPI specific support, prior to
addition of i2c equivalent devices.
* ad7606
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* ad7746
- Replace opencoded byte swapped i2c calls with _swapped variants.
- White space and line break readability improvements.
- Reorder includes and variable declarations where appropriate.
* ad7791
- Changes to the AD ADC library used by this driver took in the
sampling frequency. This lead to be the wrong path being the one
tied to the resulting attribute, so it didn't work, and a warning
to be printed.
* ad7780
- Remove apparent support for sampling frequency control on devices
that don't support changing the sampling attributes.
* ade7854
- Fix a read of the wrong number of bits.
- Improve error handling on i2c read/write errors.
- Rework i2c and spi code to reduce duplication.
* adis16201 (staging)
- Improve meaning inherent in some macro names by adding units etc
where relevant.
- Adjust comments to improve detail and drop the irrelevant.
- Rename register address definitions definitions to add a _REG
postfix, clearly separating them from field definitions. Reorganize
the definitions to group register address and fields.
- Use sign_extend32 rather than open coding.
- Reverse Xmas tree ordering where appropriate and align function args.
- Remove unused headers.
- Use GENMASK where appropriate instead of open coding.
* adis16209 (staging)
- Indent field definitions to visually separate them from
register address definitions.
- Use reverse xmas tree ordering where appropriate.
- Add some whitespace where it will help readability.
- Drop some unused headers.
- Use GENMASK where appropriate.
* ad2s1200
- Drop unnecessary includes and reorder alphabetically.
- Reverse xmas tree and blank line cleanups.
* atlas-ph-sensor
- Use msleep instead of usleep_range where the precise value doesn't
matter and the delays are long.
* bcm150
- Drop transaction splitting as core now handles it.
* cros_ec
- Move the shared header to the include/iio/common directory.
This brings it inline with the other multiple type devices.
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* hid-sensors
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* inv_mpu6050
- Clear out a second function definition for the same function.
- Don't flush fifo when the iio buffer is full but just drop excess
data.
- Tidy up set_power_itg and ensure it is used in the right places.
- Use set_power_itg rather than opencoding it again in the i2c mux
control.
- Make sure error paths disable the power if undoing power on.
- Used managed devm_ functions during probe. Delete remove function.
- Refactor to pull raw data read out of read_raw function.
- Simplify data reading error paths.
- Only enable the i2c mux for chips with the i2c aux bus (not icm20608)
- Fix a potential deadlock due to varying lock ordering.
- Fix an issue where first sample from gyro after enabling is unstable
by dropping the first sample.
- Fix an issue where the user_ctrl register is incorrectly overwritten.
- Tidy up some grammar and spelling minor issus.
* mcp320x
- Use vendor compatible strings.
* mcp4018
- Switch to using i2c .probe_new.
* mcp4351
- switch to using i2c .probe_new.
* meson-adc
- rework handing on common ADC platform data so it can be shared
across multiple families of SoCs.
* sca3000
- Fix an error handling path if the ring configure fails.
* st_lsm6dsx
- Fix a wrong fifo threshold mask (no actual effect)
* stm32-dfsdm
- Style fixes and cleanups.
- Check filter ID is in range and check spi-max-frequency.
* tsl2x7x (staging)
- Drop some unnecessary function calls, unused variables and
unnecessary local variables.
- Fix wrong interrupt type.
- Avoid unnecessary double clear of interrupt.
- Simplify proximity calibration call which did various things
unrelated to actually calibrating.
- Separate control of the proximity and ALS interrupts.
- Improve consistency of logging.
- Separate ALS and proximity persistence settings as they have
separate hardware controls.
- Tidy up variable ordering.
- Add Brian to copyright notice given consider work on this driver.
- Take advantage of hardware support for I2C address auto increment.
- Combine individuaal enable and period attributes for the two
directions on the threshold events into a single value as the
hardware doesn't separate them.
- Move integration_time* attributes from light channel to
intensity value as they effect the intensity readings directly
and the light reading only indirectly. Hence this better
reflects reality. Also move the calibscale_available.
- Avoid returning an error in the IRQ handler.
- Hard code the reg value in _clear_interrupts as it only takes
one value in the code. Result is the function has little
purpose so opencode the two remaining i2c_smbus_write_byte
calls.
- Drop some unnecessary checking of the chip status register.
- Tidy up return path in _write_interrupt_config.
- Tidy up the ID verification code.
- Move the power and diode settings defines into the header as these
are needed for platform data configuration.
- Various renames and comment cleanups for consistency and clarity.
- Use actual device defaults for default startup settings.
- SPDX
- Add some range sanity checking to sysfs attribute writes.
- Don't provide event interfaces if the interrupt line isn't available.
- Use IIO_CONST_ATTR macro for calibscale_available as it's a constant
string.
- Fix the integration time and lux equations.
- Make device IDs explicit index values in the device_channel_config array.
-----BEGIN PGP SIGNATURE-----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=egCX
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.18a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
1st round of IIO new device support, features and cleanup for the 4.18 cycle
A nice mix this time of excellent cleanups (many to send drivers
speeding toward staging graduations) and new drivers / device support.
A good part of this is Brian Masney's never ending task on the tsl2x7x
driver. The end is in sight so hopefully we'll get that one out of
staging very soon!
New device support
* AD5686
- Support AD5685R (was wrongly present as AD5685)
- Support AD5672R, AD5676, AD5676, AD5684R and AD5686R 4 and 8 channel
SPI DACs with various precisions.
- Support AD5671R, AD5675R, AD5694, AD5694R, AD5695R, AD5696 and AD5696R
I2C DACs with various percisions and numbers of channels.
* Analog front end rescale driver - New driver.
- Support current sensing usings a shunt resistor.
- Support simple voltage dividers.
- support simple current sense amplifiers.
* TI dac5571
- New driver and device bindings supporting:
dac5571, dac6571, dac7571, dac5574, dac6574, dac7574,
dac5573, dac6573 and dac7573
* Meson-adc
- Support for Meson AXG with DT bindings.
* mpu6050
- Support the mpu9255 which only requires additional WHOAMI entry and
compatible string.
* st_lsm6dsx
- Support for lsm330dlc combinded accelerometer and gyro sensors with
DT bindings.
* stm32_adc
- Add support for STM32MP1 with bindings.
Staging graduations
* adis16201 after some excelent cleanup by Himanshu Jha.
* adis16029 after some excelent cleanup by Shreeya Patel.
New features:
* ABI docs
- Add core ABI docs for angle channels.
* inv_mpu6050
- Provide support for the full range of interrupts the device
supports.
* st_accel
- Add SMO8840 ACPI ID seen in the wild on some Lenovo machines.
* stx104
- Provide a multiple gpio get function.
Cleanups / Minor fixes
* core
- Use new nested structure support to improve kernel-doc.
* ad2s1200
- Use be16_to_cpup instead of opencoding.
* ad5686
- Indentation tidy up.
- Switch to SPDX
- Refactor to allow various numbers of channels.
- Refactor to separate core and SPI specific support, prior to
addition of i2c equivalent devices.
* ad7606
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* ad7746
- Replace opencoded byte swapped i2c calls with _swapped variants.
- White space and line break readability improvements.
- Reorder includes and variable declarations where appropriate.
* ad7791
- Changes to the AD ADC library used by this driver took in the
sampling frequency. This lead to be the wrong path being the one
tied to the resulting attribute, so it didn't work, and a warning
to be printed.
* ad7780
- Remove apparent support for sampling frequency control on devices
that don't support changing the sampling attributes.
* ade7854
- Fix a read of the wrong number of bits.
- Improve error handling on i2c read/write errors.
- Rework i2c and spi code to reduce duplication.
* adis16201 (staging)
- Improve meaning inherent in some macro names by adding units etc
where relevant.
- Adjust comments to improve detail and drop the irrelevant.
- Rename register address definitions definitions to add a _REG
postfix, clearly separating them from field definitions. Reorganize
the definitions to group register address and fields.
- Use sign_extend32 rather than open coding.
- Reverse Xmas tree ordering where appropriate and align function args.
- Remove unused headers.
- Use GENMASK where appropriate instead of open coding.
* adis16209 (staging)
- Indent field definitions to visually separate them from
register address definitions.
- Use reverse xmas tree ordering where appropriate.
- Add some whitespace where it will help readability.
- Drop some unused headers.
- Use GENMASK where appropriate.
* ad2s1200
- Drop unnecessary includes and reorder alphabetically.
- Reverse xmas tree and blank line cleanups.
* atlas-ph-sensor
- Use msleep instead of usleep_range where the precise value doesn't
matter and the delays are long.
* bcm150
- Drop transaction splitting as core now handles it.
* cros_ec
- Move the shared header to the include/iio/common directory.
This brings it inline with the other multiple type devices.
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* hid-sensors
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* inv_mpu6050
- Clear out a second function definition for the same function.
- Don't flush fifo when the iio buffer is full but just drop excess
data.
- Tidy up set_power_itg and ensure it is used in the right places.
- Use set_power_itg rather than opencoding it again in the i2c mux
control.
- Make sure error paths disable the power if undoing power on.
- Used managed devm_ functions during probe. Delete remove function.
- Refactor to pull raw data read out of read_raw function.
- Simplify data reading error paths.
- Only enable the i2c mux for chips with the i2c aux bus (not icm20608)
- Fix a potential deadlock due to varying lock ordering.
- Fix an issue where first sample from gyro after enabling is unstable
by dropping the first sample.
- Fix an issue where the user_ctrl register is incorrectly overwritten.
- Tidy up some grammar and spelling minor issus.
* mcp320x
- Use vendor compatible strings.
* mcp4018
- Switch to using i2c .probe_new.
* mcp4351
- switch to using i2c .probe_new.
* meson-adc
- rework handing on common ADC platform data so it can be shared
across multiple families of SoCs.
* sca3000
- Fix an error handling path if the ring configure fails.
* st_lsm6dsx
- Fix a wrong fifo threshold mask (no actual effect)
* stm32-dfsdm
- Style fixes and cleanups.
- Check filter ID is in range and check spi-max-frequency.
* tsl2x7x (staging)
- Drop some unnecessary function calls, unused variables and
unnecessary local variables.
- Fix wrong interrupt type.
- Avoid unnecessary double clear of interrupt.
- Simplify proximity calibration call which did various things
unrelated to actually calibrating.
- Separate control of the proximity and ALS interrupts.
- Improve consistency of logging.
- Separate ALS and proximity persistence settings as they have
separate hardware controls.
- Tidy up variable ordering.
- Add Brian to copyright notice given consider work on this driver.
- Take advantage of hardware support for I2C address auto increment.
- Combine individuaal enable and period attributes for the two
directions on the threshold events into a single value as the
hardware doesn't separate them.
- Move integration_time* attributes from light channel to
intensity value as they effect the intensity readings directly
and the light reading only indirectly. Hence this better
reflects reality. Also move the calibscale_available.
- Avoid returning an error in the IRQ handler.
- Hard code the reg value in _clear_interrupts as it only takes
one value in the code. Result is the function has little
purpose so opencode the two remaining i2c_smbus_write_byte
calls.
- Drop some unnecessary checking of the chip status register.
- Tidy up return path in _write_interrupt_config.
- Tidy up the ID verification code.
- Move the power and diode settings defines into the header as these
are needed for platform data configuration.
- Various renames and comment cleanups for consistency and clarity.
- Use actual device defaults for default startup settings.
- SPDX
- Add some range sanity checking to sysfs attribute writes.
- Don't provide event interfaces if the interrupt line isn't available.
- Use IIO_CONST_ATTR macro for calibscale_available as it's a constant
string.
- Fix the integration time and lux equations.
- Make device IDs explicit index values in the device_channel_config array.
