master side report:
silvaco-i3c-master 44330000.i3c-master: Error condition: MSTATUS 0x020090c7, MERRWARN 0x00100000
BIT 20: TIMEOUT error
The module has stalled too long in a frame. This happens when:
- The TX FIFO or RX FIFO is not handled and the bus is stuck in the
middle of a message,
- No STOP was issued and between messages,
- IBI manual is used and no decision was made.
The maximum stall period is 100 μs.
This can be considered as being just a warning as the system IRQ latency
can easily be greater than 100us.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-7-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Upon IBIWON timeout, the SDA line will always be kept low if we don't emit
a stop. Calling svc_i3c_master_emit_stop() there will let the bus return to
idle state.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-6-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
MSTATUS[RXPEND] is only updated after the data transfer cycle started. This
creates an issue when the I3C clock is slow, and the CPU is running fast
enough that MSTATUS[RXPEND] may not be updated when the code reaches
checking point. As a result, mandatory data can be missed.
Add a wait for MSTATUS[COMPLETE] to ensure that all mandatory data is
already in FIFO. It also works without mandatory data.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-4-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
┌─────┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┌─────
SCL: ┘ └─────┛ └──┛ └──┛ └──┛ └──┛ └──┛ └──┛ └──┛ └──┘
───┐ ┌─────┐ ┌─────┐ ┌───────────┐
SDA: └───────────────────────┘ └─────┘ └─────┘ └─────
xxx╱ ╲╱ ╲╱ ╲╱ ╲╱ ╲
: xxx╲IBI ╱╲ Addr(0x0a) ╱╲ RW ╱╲NACK╱╲ S ╱
If an In-Band Interrupt (IBI) occurs and IBI work thread is not immediately
scheduled, when svc_i3c_master_priv_xfers() initiates the I3C transfer and
attempts to send address 0x7e, the target interprets it as an
IBI handler and returns the target address 0x0a.
However, svc_i3c_master_priv_xfers() does not handle this case and proceeds
with other transfers, resulting in incorrect data being returned.
Add IBIWON check in svc_i3c_master_xfer(). In case this situation occurs,
return a failure to the driver.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-3-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The ibi work thread operates asynchronously with other transfers, such as
svc_i3c_master_priv_xfers(). Introduce mutex protection to ensure the
completion of the entire i3c/i2c transaction.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-2-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The MIPI I3C spec refers to a Provisioned ID, since it is (sometimes)
provisioned at device manufacturing.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20231003075339.197099-1-matt@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Host Controller goes to halt state after aborted transfer and needs to
be resumed by SW. Add this resuming to DMA mode code too.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-13-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
On an HW I'm using in enabling work the RESUME bit is not set in the
HC_CONTROLLER register when Host Controller goes to halt state. Value 1
should mean controller is suspended when reading and writing 1 resumes it.
Because of this erratic behaviour plain HC_CONTROL read and write back
won't resume the controller. Therefore do it by setting the RESUME bit
explicitly.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-12-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Due to missing completion object for the ENTDAA command transfer in the
hci_cmd_v1_daa() the wait_for_completion_timeout() will obviously
timeout even the transfer itself may succeed.
Fix this by setting the xfer->completion to the already initialized
completion object.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-11-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix following warning (with CONFIG_DMA_API_DEBUG) which happens with a
transfer without a data buffer.
DMA-API: i3c mipi-i3c-hci.0: device driver tries to free DMA memory it has not allocated [device address=0x0000000000000000] [size=0 bytes]
For those transfers the hci_dma_queue_xfer() doesn't create a mapping and
the DMA address pointer xfer->data_dma is not set.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-10-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Number of software enabled Ring Bundles must be set before using them.
Otherwise Ring will not start and may be power-gated by the Host
Controller.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-9-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
If there is a transfer error during i3c_master_bus_init() and code goes
doing the bus cleanup in i3c_hci_bus_cleanup() there is possibility that
i3c_hci_irq_handler() is running in parallel with hci->io->cleanup()
which can be racy.
Prevent this by waiting there is no pending interrupt on other CPU
before doing the IO cleanup.
This was observed with ring headers where first transfer failed and
sometimes transfer error or ring transfer abort interrupt was coming
simultaneously with the bus cleanup path.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-8-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Set ring start request together with ring enable in hci_dma_init(). This
causes the ring abort request in hci_dma_dequeue_xfer() will raise the
INTR_RING_OP (RING_OP_STAT in MIPI I3C HCI specification) interrupt in
the RH_INTR_STATUS register.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-7-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Ring Abort request will timeout in case there is an error in the Host
Controller interrupt delivery or Ring Header configuration. Using BUG()
makes hard to debug those cases.
Make it less severe and turn BUG() to WARN_ON().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-6-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Do not loop over ring headers in hci_dma_irq_handler() that are not
allocated and enabled in hci_dma_init(). Otherwise out of bounds access
will occur from rings->headers[i] access when i >= number of allocated
ring headers.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-5-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
MIPI I3C HCI specification v1.1 describes the ENTRY_SIZE field for the
Device Address Table (DAT) and the Device Characteristics Table (DCT)
section offset registers (DAT_SECTION_OFFSET and DCT_SECTION_OFFSET).
That field is not documented in earlier version.
ENTRY_SIZE value 0 is meant to be backward compatible. For the DAT entry
size it is interpreted as 2 DWORDs (8-bytes) and for the DCT entry size
as 4 DWORDs (16-bytes). Values 1-15 are reserved for future use.
New version I believe fixes also the TABLE_SIZE field description.
Before it was defined in DWORDs which I believe is incorrect since the
DAT/DCT table entry structures, and sizes, are described having
8-bytes/16-bytes entries.
This is more clear in the specification v1.1 which states the TABLE_SIZE
fields are interpreted as number of entries in the DAT/DCT tables. I
believe this same holds also in earlier version, at least it makes more
sense.
Fix code accordingly and let the DAT_entry_size and the DCT_entry_size
variables carry the size as bytes. Which is how it is already
interpreted in the dat_v1.c: hci_dat_v1_init().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-4-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add MODULE_ALIAS() in order to be able to autoload this driver when the
device is added as a platform device from another glue code driver.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-3-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct svc_i3c_xfer.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Conor Culhane <conor.culhane@silvaco.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: linux-i3c@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230922175023.work.239-kees@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct hci_rings_data.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Nicolas Pitre <npitre@baylibre.com>
Cc: Len Baker <len.baker@gmx.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: linux-i3c@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230922175019.work.129-kees@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct cdns_i3c_xfer.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: "Przemysław Gaj" <pgaj@cadence.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: linux-i3c@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230922175014.work.637-kees@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct dw_i3c_xfer.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Joel Stanley <joel@jms.id.au>
Cc: linux-i3c@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230922175011.work.800-kees@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
I3C masters are expected to support hot-join. This means at initialization
time we might not yet discover any device and this should not be treated
as a fatal error.
During the DAA procedure which happens at probe time, if no device has
joined, all CCC will be NACKed (from a bus perspective). This leads to an
early return with an error code which fails the probe of the master.
Let's avoid this by just telling the core through an I3C_ERROR_M2
return command code that no device was discovered, which is a valid
situation. This way the master will no longer bail out and fail to probe
for a wrong reason.
Cc: stable@vger.kernel.org
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230831141324.2841525-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The 'saved_regs' member of the 'svc_i3c_master' structure is not
described in the kernel doc, which produces the following warning:
Function parameter or member 'saved_regs' not described in 'svc_i3c_master'
Add the missing line in the kernel documentation of the parent
structure.
Fixes: 1c5ee2a77b ("i3c: master: svc: fix i3c suspend/resume issue")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202308171435.0xQ82lvu-lkp@intel.com/
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230817101853.16805-1-miquel.raynal@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
It is not possible for platform_get_irq() to return 0. Use the
return value from platform_get_irq().
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230803085149.149248-1-ruanjinjie@huawei.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The exit criteria for the DAA should check if the data length is equal to
1, instead of checking if the response status is equal to 1.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20230802100909.2568215-1-billy_tsai@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230714174623.4057784-1-robh@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add NACK check after start byte is sent.
It is possible to detect early that a device is not on the bus
and avoid invalid transmissions thereafter.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230517033030.3068085-3-xiaoning.wang@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
pm_runtime_resume_and_get() may call sleep(). It cannot be used in
svc_i3c_master_start_xfer_locked(), because it is in a spin lock.
Move the pm runtime operations to svc_i3c_master_enqueue_xfer().
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Fixes: 05be23ef78 ("i3c: master: svc: add runtime pm support")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230517033030.3068085-2-xiaoning.wang@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When system suspends, if i3c module is powered down, register
value will lose.
Need to save the key registers before system suspend.
So save these registers value in runtime pm suspend, and restore them
if these register's value is different with the saved values
when runtime pm resume.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230517033030.3068085-1-xiaoning.wang@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
smatch reports
drivers/i3c/master/ast2600-i3c-master.c:121:34: warning: symbol
'ast2600_i3c_ops' was not declared. Should it be static?
This variable is only used in its defining file, so it should be static.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230429134601.2688558-1-trix@redhat.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The 2k register setting is zero, OR-ing it in doesn't parallel the 2k
and 750 ohm pullups. We need a separate value for the 545 ohm setting.
Reported-by: Lukwinski Zbigniew <zbigniew.lukwinski@linux.intel.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230428001849.1775559-1-jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The ast2600 i3c hardware is capable of IBIs, but we need a workaround
for a hardware issue with the I3C state machine handling IBI payloads
of specific lengths when PEC is not enabled. To avoid this, we need to
unconditionally enable PECs, at the consquence of losing a byte of data
when the device does not send a PEC.
Enable IBIs on the ast2600 platform, including an implementation of the
PEC workaround, which prints a warning when triggered.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/ba923b96d6d129024c975e8a0472c5b2fcb3af32.1680161823.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
On the AST2600 i3c controller, we'll need to apply a workaround for a
hardware issue with IBI payloads.
Introduce a platform hook to allow dw i3c platform implementations to
modify the DAT entry in IBI enable/disable to allow this workaround in a
future change.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/d5d76a8d2336d2a71886537f42e71d51db184df6.1680161823.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This change adds support for receiving and dequeueing i3c IBIs.
By setting struct dw_i3c_master->ibi_capable before probe, a platform
implementation can select the IBI-enabled version of the i3c_master_ops,
enabling the global IBI infrastrcture for that controller.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/79daeefd7ccb7c935d0c159149df21a6c9a73ffa.1680161823.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In an upcoming change, we will want to store additional data about the
devices we have in the data address table.
Change the type of the DAT entries into a struct, which currently just
has the address data.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/9dc0d9e2857e851a0cf04819df48e5d31921f83e.1680161823.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In a future change we'll want to read from the IBI FIFO too, so turn
dw_i3c_read_rx_fifo() into a generic read with the FIFO register as a
parameter.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/827204789583dd86addffb47ecaeab9d67cf95d5.1680161823.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Now that we have platform-specific infrastructure for the dw i3c driver,
add platform support for the ASPEED AST2600 SoC.
The AST2600 has a small set of "i3c global" registers, providing
platform-level i3c configuration outside of the i3c core.
For the ast2600, we need a couple of extra setup operations:
- on probe: find the i3c global register set and parse the SDA pullup
resistor values
- on init: set the pullups accordingly, and set the i3c instance IDs
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20230331091501.3800299-4-jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The dw i3c core can be integrated into various SoC devices. Platforms
that use this core may need a little configuration that is specific to
that platform.
Add some infrastructure to allow platform-specific behaviour: common
probe/remove functions, a set of platform hook operations, and a pointer
for platform-specific data in struct dw_i3c_master. Move the common api
into a new (i3c local) header file.
Platforms will provide their own struct platform_driver, which allocates
struct dw_i3c_master, does any platform-specific probe behaviour, and
calls into the common probe.
A future change will add new platform support that uses this
infrastructure.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20230331091501.3800299-2-jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In the clock setup path, we set the hardware DEV_CTRL_I2C_SLAVE_PRESENT
bit on a shared mode bus, then read-back this bit for the conditional
tCAS set.
Instead, just use the bus->mode setting for the conditional test.
While we're at it, add a little comment about why the conditional is
there.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/92a933566f7846708a00ad7f5a16ee8e6ed32d0e.1680156630.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
We currently assume that the rx_len of a read command will be as
submitted, but we may have a shorter read than expected.
This change populates the output i3c xfer length from the actually-read
length.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/f4fff7ab18dee1f662dc7a5a4111fcd921e6792b.1680156630.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230318233311.265186-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230318233311.265186-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230318233311.265186-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230318233311.265186-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The function returned zero unconditionally. Switch the return type to void
and simplify the callers accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230318233311.265186-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here). This
also fixes !CONFIG_OF error:
drivers/i3c/master/dw-i3c-master.c:1201:34: error: ‘dw_i3c_master_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230312132535.352246-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Bus-speed could be default(12.5MHz) or defined by users in dts.
Dw-i3c-master should not hard-code the initial speed to be
I3C_BUS_TYP_I3C_SCL_RATE (12.5MHz)
And because of Synopsys's I3C controller limit (hcnt/lcnt register
length) and core-clk provided, there is a limit to bus speed, too.
For example, when core-clk is 250 MHz, the bus speed cannot be
lowered below 1MHz.
Tested: tested with an i3c sensor and captured with a logic analyzer.
Signed-off-by: Jack Chen <zenghuchen@google.com>
Link: https://lore.kernel.org/r/20230216151057.293764-1-zenghuchen@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Clang static analysis reports this problem
dw-i3c-master.c:799:9: warning: The result of the left shift is
undefined because the left operand is negative
COMMAND_PORT_DEV_INDEX(pos) |
^~~~~~~~~~~~~~~~~~~~~~~~~~~
pos can be negative because dw_i3c_master_get_free_pos() can return an
error. So check for an error.
Fixes: 1dd728f5d4 ("i3c: master: Add driver for Synopsys DesignWare IP")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220108150948.3988790-1-trix@redhat.com
The referred config BIG_ENDIAN does not exist. The config for the
endianness of the CPU architecture is called CPU_BIG_ENDIAN.
Correct the config name to the existing config for the endianness.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220103094504.3602-1-lukas.bulwahn@gmail.com
If enable interrupt in the svc_i3c_master_bus_init() but do not call
enable ibi in the device driver, it will cause a kernel dump in the
svc_i3c_master_handle_ibi() when a slave start occurs on the i3c bus,
because the data->ibi_pool is not initialized.
So only enable the interrupt in svc_i3c_master_enable_ibi() function.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211227074529.1660398-9-xiaoning.wang@nxp.com
The missing MODULE_DEVICE_TABLE() will cause the svc-i3c-master cannot
be auto probed when it is built in moudle.
So add it.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211227074529.1660398-8-xiaoning.wang@nxp.com
Add runtime pm support to dynamically manage the clock.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211227074529.1660398-7-xiaoning.wang@nxp.com
If using I2C/I3C mixed mode, need to set ODSTOP. Otherwise, the I2C
devices cannot see the stop signal. It may cause message sending errors.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211227074529.1660398-6-xiaoning.wang@nxp.com
When i3c controller reads data from slave device, slave device can stop
returning data with an ACK after any byte.
Add this support for svc i3c controller. Otherwise, it will timeout
when the slave device ends the read operation early.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211227074529.1660398-5-xiaoning.wang@nxp.com
Sometimes only need to reset err and fifo regs, so split the origin
reset function to three functions.
Put them at the top of the file, to let more functions can call them.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211227074529.1660398-4-xiaoning.wang@nxp.com
do_daa_locked() function is in a spin lock environment, use
readl_poll_timeout_atomic() to replace the origin
readl_poll_timeout().
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211227074529.1660398-3-xiaoning.wang@nxp.com
Reset I3C module will R/W its regs, so enable its clocks first.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211227074529.1660398-2-xiaoning.wang@nxp.com
The code in 'hci_dat_v1_get_index()' really looks like a hand coded version
of 'for_each_set_bit()', except that a +1 is missing when searching for the
next set bit.
This really looks odd and it seems that it will loop until 'dat_w0_read()'
returns the expected result.
So use 'for_each_set_bit()' instead. It is less verbose and should be more
correct.
Fixes: 9ad9a52cce ("i3c/master: introduce the mipi-i3c-hci driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/0cdf3cb10293ead1acd271fdb8a70369c298c082.1637186628.git.christophe.jaillet@wanadoo.fr
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
So, use the purpose specific kcalloc() function instead of the argument
size * count in the kzalloc() function.
[1] https://www.kernel.org/doc/html/v5.14/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments
Signed-off-by: Len Baker <len.baker@gmx.com>
Acked-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210912155135.7541-1-len.baker@gmx.com
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
So, use the struct_size() helper to do the arithmetic instead of the
argument "size + count * size" in the kzalloc() function.
[1] https://www.kernel.org/doc/html/v5.14/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments
Signed-off-by: Len Baker <len.baker@gmx.com>
Acked-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210905144054.5124-1-len.baker@gmx.com
Drivers:
- svc: two small fixes
-----BEGIN PGP SIGNATURE-----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=iMi5
-----END PGP SIGNATURE-----
Merge tag 'i3c/for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
- two small fixes to the svc driver
* tag 'i3c/for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: svc: fix doc warning in svc-i3c-master.c
i3c: master: svc: drop free_irq of devm_request_irq allocated irq
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of letting the code fall
through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Fix the following make W=1 warning:
drivers/i3c/master/svc-i3c-master.c:207: warning: expecting prototype for struct svc_i3c_i3c_dev_data. Prototype was for struct svc_i3c_i2c_dev_data instead
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210602085544.4101980-1-yangyingliang@huawei.com
irq allocated with devm_request_irq() will be freed in devm_irq_release(),
using free_irq() in ->remove() will causes a dangling pointer, and a
subsequent double free. So remove the free_irq() in svc_i3c_master_remove().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210602084935.3977636-1-yangyingliang@huawei.com
The assignment of xfer_len to cmd->read_len appears to be redundant
as the next statement re-assigns the value 0 to it. Clean up the
code by removing the redundant first assignment.
Addresses-Coverity: ("Unused value")
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210224151349.202332-1-colin.king@canonical.com
Disabling all event calls is already handled by the core right before
starting the DAA process. Do not do it again when the DAA process
completes, it is redundant.
Fixes: 1dd728f5d4 ("i3c: master: Add driver for Synopsys DesignWare IP")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201228105501.6104-1-miquel.raynal@bootlin.com
Add support for Silvaco I3C dual-role IP. The master role is supported
in SDR mode only. I2C transfers have not been tested but are shared
because they are very close to the I3C transfers in terms of register
configuration.
The IBI processing follows this logic:
- When a slave advertizes an interrupt (SDA pulled low) an interrupt
gets generated by the master. This time is unbounded and may be
deferred.
- The IRQ handler itself does not process anything: it only queues a
work that will be run in non-atomic context. This is needed because
short wait periods must be experienced.
- The IBI job is divided in two parts: the first one is "critical" in
the sense that it may not support getting interrupted. If this
happens, after this first section the driver checks the master error
register and depending on its content either flushes everything and
errors out, or ends the processing (this second section may be
interrupted).
- If the critical section got interrupted, the slave will
automatically respin it's IBI request when it will be allowed to.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210121101808.14654-6-miquel.raynal@bootlin.com
The MIPI i3c HCI driver makes use of IOMEM functions like
devm_platform_ioremap_resource(), which are only available if
CONFIG_HAS_IOMEM is defined.
This causes the driver to be enabled under make ARCH=um allyesconfig,
even though it won't build.
By adding a dependency on HAS_IOMEM, the driver will not be enabled on
architectures which don't support it.
Fixes: 9ad9a52cce ("i3c/master: introduce the mipi-i3c-hci driver")
Signed-off-by: David Gow <davidgow@google.com>
Acked-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210127040636.1535722-1-davidgow@google.com
Clang warns:
../drivers/i3c/master/mipi-i3c-hci/core.c:780:21: warning: attribute
declaration must precede definition [-Wignored-attributes]
static const struct __maybe_unused of_device_id i3c_hci_of_match[] = {
^
../include/linux/compiler_attributes.h:267:56: note: expanded from macro
'__maybe_unused'
#define __maybe_unused __attribute__((__unused__))
^
../include/linux/mod_devicetable.h:262:8: note: previous definition is
here
struct of_device_id {
^
1 warning generated.
'struct of_device_id' should not be split, as it is a type. Move the
__maybe_unused attribute after the static and const qualifiers so that
there are no warnings about this variable, period.
Fixes: 95393f3e07 ("i3c/master/mipi-i3c-hci: quiet maybe-unused variable warning")
Link: https://github.com/ClangBuiltLinux/linux/issues/1221
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201222025931.3043480-1-natechancellor@gmail.com
If CONFIG_OF is disabled then the matching table is notreferenced.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
The variable next_addr is not initialized and is being used in a call
to i3c_master_get_free_addr as a starting point to find the next address.
Fix this by initializing next_addr to 0 to avoid an uninitialized garbage
starting address from being used.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 9ad9a52cce ("i3c/master: introduce the mipi-i3c-hci driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-i3c/20201124123504.396249-1-colin.king@canonical.com
This adds basic support for hardware implementing the MIPI I3C HCI
specification. This driver is currently limited by the capabilities
of the I3C subsystem, meaning things like scheduled commands,
auto-commands and NCM mode are not yet supported.
This supports version 1.0 of the MIPI I3C HCI spec, as well as the
imminent release of version 1.1. Support for draft version 2.0 of the
spec is also largely included with the caveat that future adjustments
to this code are likely as the spec is still a work in progress.
This is also lightly tested as actual hardware is still very scarce,
even for HCI v1.0. Hence the EXPERIMENTAL tag. Further contributions
to this driver are expected once vendor implementations and new I3C
devices become available.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-i3c/20201111220510.3622216-3-nico@fluxnic.net
* Fix an error path in the cadence driver
-----BEGIN PGP SIGNATURE-----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=yC+2
-----END PGP SIGNATURE-----
Merge tag 'i3c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Boris Brezillon:
- Fix DAA for the pre-reserved address case
- Fix an error path in the cadence driver
* tag 'i3c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: Fix error return in cdns_i3c_master_probe()
i3c: master: fix for SETDASA and DAA process
i3c: master add i3c_master_attach_boardinfo to preserve boardinfo
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-i3c/20200227131307.GA24935@embeddedor
For today the reattach function only update the device address on the
controller.
Update the location to the first available too, will optimize the
enumeration process avoiding additional checks to keep the available
positions on address table consecutive.
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
This patch adds support for THD_DEL (Data Hold Delay) to Cadence
I3C master constoller driver.
As per MIPI I3C Specification 1.0, Table 75 (page 142) defines
non-zero minimal tHD_PP timing on master output (Fig 65). This
setting allows to meet this timing on master's soc outputs,
regardless of PCB balancing.
Signed-off-by: Przemyslaw Gaj <pgaj@cadence.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
I need to store address and lvr value for I2C devices without static definition
in DT. This allows secondary master to transmit DEFSLVS command properly.
Main changes between v4 and v5:
- Change in defslvs to use addr and lvr from i2c_dev_desc structure
- Change in CDNS and DW drivers to use addr and lvr from i2c_dev_desc structure
Signed-off-by: Przemyslaw Gaj <pgaj@cadence.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
This simplifies and standardizes slot manipulation code
by using for_each_set_bit() library function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
* Add support for limited bus mode
* Fix the Cadence DT binding doc
* Use struct_size() to allocate a DEFSLVS packet
-----BEGIN PGP SIGNATURE-----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=Uj8o
-----END PGP SIGNATURE-----
Merge tag 'i3c/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull ic3 updates from Boris Brezillon:
- Drop support for 10-bit I2C addresses
- Add support for limited bus mode
- Fix the Cadence DT binding doc
- Use struct_size() to allocate a DEFSLVS packet
* tag 'i3c/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: Use struct_size() helper
dt-bindings: i3c: cdns: Use correct cells for I2C device
i3c: dw: add limited bus mode support
i3c: add mixed limited bus mode
i3c: fix i2c and i3c scl rate by bus mode
dt-bindings: i3c: Document dropped support for I2C 10 bit devices
i3c: Drop support for I2C 10 bit addresing
This patch add limited bus mode support for DesignWare i3c master
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
This patch drops support for I2C devices with 10 bit addressing. When I2C
device with 10 bit address is defined in DT, I3C master registration fails.
Address space for I2C devices has been reduced and ->i2c_funcs() hook has been
removed.
Because this patch series dropped support for 10 bit I2C devices, support is
also dropped in Cadence I3C master driver and Synopsys DesignWare I3C master
driver.
Signed-off-by: Przemyslaw Gaj <pgaj@cadence.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Remove dead code in the DW driver
-----BEGIN PGP SIGNATURE-----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=/U9S
-----END PGP SIGNATURE-----
Merge tag 'i3c/for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c update from Boris Brezillon:
- Fix a shift wrap bug in the core
- Remove dead code in the DW driver
* tag 'i3c/for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: Fix a shift wrap bug in i3c_bus_set_addr_slot_status()
i3c: master: dw: remove dead code from dw_i3c_master_*_xfers()
The controller was being disabled incorrectly. The correct way is to clear
the DEV_CTRL_ENABLE bit.
Fix this by clearing this bit.
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: <stable@vger.kernel.org>
Fixes: 1dd728f5d4 ("i3c: master: Add driver for Synopsys DesignWare IP")
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Detected by CoverityScan (Event result_independent_of_operands):
"(i3c_xfers + i).len > 65536" is always false regardless of the values
of its operands. This occurs as the logical operand of "if"
"(i2c_xfers + i).len > 65536" is always false regardless of the values
of its operands. This occurs as the logical operand of "if"
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
- Update the I3C entries in MAINTAINERS to add an IRC chan
-----BEGIN PGP SIGNATURE-----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=Ijxi
-----END PGP SIGNATURE-----
Merge tag 'i3c/for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Boris Brezillon:
- Add a /* fall-through */ comment in the dw-i3c-master driver
- Update the I3C entries in MAINTAINERS to add an IRC chan
* tag 'i3c/for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: dw-i3c-master: mark expected switch fall-through
MAINTAINERS: Add an IRC channel for the I3C subsystem
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/i3c/master/dw-i3c-master.c: In function ‘dw_i3c_master_bus_init’:
drivers/i3c/master/dw-i3c-master.c:603:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (ret)
^
drivers/i3c/master/dw-i3c-master.c:605:2: note: here
case I3C_BUS_MODE_PURE:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
In dw_i3c_master_irq_handler(), we already have gotten
&master->xferqueue.lock, if we try to get the same lock again in
dw_i3c_master_dequeue_xfer(), deadlock happens.
We fix this issue by introduing dw_i3c_master_dequeue_xfer_locked()
which does all what dw_i3c_master_dequeue_xfer() does without trying
to lock &master->xferqueue.lock.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
This patch fix i3c_attach/reattach functions.
During the i3c_attach the driver ignores the static address used for
SETDASA CCC command.
During the i3c_reattach the driver doesn't update master->addrs[data->index]
with new address if old_dyn_addr = 0.
Fixes: 1dd728f5d4 ("i3c: master: Add driver for Synopsys DesignWare IP")
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
This patch fixes I2C transfers in Cadence I3C master driver.
There was no way to queue more than one I2C transfer before.
Fixes: 603f2bee2c ("i3c: master: Add driver for Cadence IP")
Signed-off-by: Przemyslaw Gaj <pgaj@cadence.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The masking operation on status is using a bitwise 'or' rather than
a bitwise 'and' operator, and hence the result is always non-zero
which is probably not what is intended. Fix this by using the correct
operator.
Detected by CoverityScan, CID#1475523 ("Wrong operator used")
Fixes: 88acc98a712a ("i3c: master: Add driver for Synopsys DesignWare IP")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/i3c/master/i3c-master-cdns.c: In function 'cdns_i3c_master_do_daa':
drivers/i3c/master/i3c-master-cdns.c:1137:16: warning:
variable 'old_i3c_scl_lim' set but not used [-Wunused-but-set-variable]
It never used since introdution in commit
acfab7d324b2 ("i3c: master: Add driver for Cadence IP")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add core infrastructure to support I3C in Linux and document it.
This infrastructure adds basic I3C support. Advanced features will be
added afterwards.
There are a few design choices that are worth mentioning because they
impact the way I3C device drivers can interact with their devices:
- all functions used to send I3C/I2C frames must be called in
non-atomic context. Mainly done this way to ease implementation, but
this is not set in stone, and if anyone needs async support, new
functions can be added later on.
- the bus element is a separate object, but it's tightly coupled with
the master object. We thus have a 1:1 relationship between i3c_bus
and i3c_master_controller objects, and if 2 master controllers are
connected to the same bus and both exposed to the same Linux instance
they will appear as two distinct busses, and devices on this bus will
be exposed twice.
- I2C backward compatibility has been designed to be transparent to I2C
drivers and the I2C subsystem. The I3C master just registers an I2C
adapter which creates a new I2C bus. I'd say that, from a
representation PoV it's not ideal because what should appear as a
single I3C bus exposing I3C and I2C devices here appears as 2
different buses connected to each other through the parenting (the
I3C master is the parent of the I2C and I3C busses).
On the other hand, I don't see a better solution if we want something
that is not invasive.
Missing features:
- I3C HDR modes are not supported
- no support for multi-master and the associated concepts (mastership
handover, support for secondary masters, ...)
- I2C devices can only be described using DT because this is the only
use case I have. However, the framework can easily be extended with
ACPI and board info support
- I3C slave framework. This has been completely omitted, but shouldn't
have a huge impact on the I3C framework because I3C slaves don't see
the whole bus, it's only about handling master requests and generating
IBIs. Some of the struct, constant and enum definitions could be
shared, but most of the I3C slave framework logic will be different
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
