The PECI CPU sensors are available as soon as the CPU is powered,
however the PECI DIMM sensors are available after DRAM has been
trained and thresholds have been written by host firmware.
The default timeout of 30 seconds isn't enough for modern multisocket
platforms utilizing DDR5 memory to bring up the memory and enable PECI
sensor data.
Bump the default timeout to 10 minutes in case the system starts
without cached DDR5 training data.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20231130090422.2535542-1-patrick.rudolph@9elements.com
[groeck: List affected driver in patch subject]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Without visibility into the initializers for data->innr, GCC suspects
using it as an index could walk off the end of the various 14-element
arrays in data. Perform an explicit clamp to the array size. Silences
the following warning with GCC 12+:
../drivers/hwmon/pc87360.c: In function 'pc87360_update_device':
../drivers/hwmon/pc87360.c:341:49: warning: writing 1 byte into a region of size 0 [-Wstringop-overflow=]
341 | data->in_max[i] = pc87360_read_value(data,
| ~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~
342 | LD_IN, i,
| ~~~~~~~~~
343 | PC87365_REG_IN_MAX);
| ~~~~~~~~~~~~~~~~~~~
../drivers/hwmon/pc87360.c:209:12: note: at offset 255 into destination object 'in_max' of size 14
209 | u8 in_max[14]; /* Register value */
| ^~~~~~
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20231130200207.work.679-kees@kernel.org
[groeck: Added comment into code clarifying context]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Setting the fan speed is only valid in manual mode; it is not possible
to set the fan's speed in automatic mode.
Return error when attempting to set the fan speed in automatic mode.
Signed-off-by: Xing Tong Wu <xingtong.wu@siemens.com>
Link: https://lore.kernel.org/r/20231121081604.2499-3-xingtong_wu@163.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The nct6116 has 2 additional PWM pins compared to the nct6106.
Extend the nct6106 PWM arrays to support the nct6116.
Signed-off-by: Xing Tong Wu <xingtong.wu@siemens.com>
Link: https://lore.kernel.org/r/20231121081604.2499-2-xingtong_wu@163.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for mp5990 device from Monolithic Power Systems, Inc. (MPS)
vendor. This is a Hot-Swap Controller.
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20231113155008.2147090-3-peteryin.openbmc@gmail.com
[groeck: Improved and clarified comments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use preferred i2c_get_match_data() instead of of_match_device() and
i2c_match_id() to get the driver match data. With this, adjust the
includes to explicitly include the correct headers.
Adjust the 'chips' enum to not use 0, so that no match data can be
distinguished from a valid enum value.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231115205703.3730448-3-robh@kernel.org
[groeck: Use double cast for enum chips assignment to make compiler happy]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Changing the "kinds" enum start value to be 1-indexed instead of
0-indexed caused look-ups in nct6775_device_names[] to be misaligned or
off the end.
Initialize the string list with explicit indexes.
Cc: Rob Herring <robh@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Fixes: 10a0575ea0 ("hwmon: nct6775-i2c: Use i2c_get_match_data()")
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use preferred i2c_get_match_data() instead of of_match_device() and
i2c_match_id() to get the driver match data. With this, adjust the
includes to explicitly include the correct headers.
Adjust the 'kinds' enum to not use 0, so that no match data can be
distinguished from a valid enum value.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231115205703.3730448-2-robh@kernel.org
[groeck: Use double cast for i2c_get_match_data() to make clang happy]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use preferred i2c_get_match_data() instead of of_match_device() and
i2c_match_id() to get the driver match data. With this, adjust the
includes to explicitly include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231115205703.3730448-1-robh@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Based on the documentation below, the maximum number of Fan tach
channels is 16:
Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt:45:
45 - aspeed,fan-tach-ch : should specify the Fan tach input channel.
46 integer value in the range 0 through 15, with 0 indicating
47 Fan tach channel 0 and 15 indicating Fan tach channel 15.
48 At least one Fan tach input channel is required.
However, the compiler doesn't know that, and legitimaly warns about a potential
overwrite in array `u8 fan_tach_ch_source[16]` in `struct aspeed_pwm_tacho_data`,
in case `index` takes a value outside the boundaries of the array:
drivers/hwmon/aspeed-pwm-tacho.c:
179 struct aspeed_pwm_tacho_data {
...
184 bool fan_tach_present[16];
...
193 u8 fan_tach_ch_source[16];
196 };
In function ‘aspeed_create_fan_tach_channel’,
inlined from ‘aspeed_create_fan’ at drivers/hwmon/aspeed-pwm-tacho.c:877:2,
inlined from ‘aspeed_pwm_tacho_probe’ at drivers/hwmon/aspeed-pwm-tacho.c:936:9:
drivers/hwmon/aspeed-pwm-tacho.c:751:49: warning: writing 1 byte into a region of size 0 [-Wstringop-overflow=]
751 | priv->fan_tach_ch_source[index] = pwm_source;
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~
drivers/hwmon/aspeed-pwm-tacho.c: In function ‘aspeed_pwm_tacho_probe’:
drivers/hwmon/aspeed-pwm-tacho.c:193:12: note: at offset [48, 255] into destination object ‘fan_tach_ch_source’ of size 16
193 | u8 fan_tach_ch_source[16];
| ^~~~~~~~~~~~~~~~~~
Fix this by sanity checking `index` before using it to index arrays of
size 16 elements in `struct aspeed_pwm_tacho_data`. Also, pass `dev` as
argument to function `aspeed_create_fan_tach_channel()`, and add an error
message in case `index` is out-of-bounds, in which case return `-EINVAL`.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/ZVPQJIP26dIzRAr6@work
[groeck: Fixed continuation line alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix some kernel-doc comments to silence the warnings:
drivers/hwmon/sht4x.c:65: warning: Function parameter or member 'valid' not described in 'sht4x_data'
drivers/hwmon/sht4x.c:73: warning: Function parameter or member 'data' not described in 'sht4x_read_values'
drivers/hwmon/sht4x.c:73: warning: Excess function parameter 'sht4x_data' description in 'sht4x_read_values'
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=7220
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20231110055341.39939-1-yang.lee@linux.alibaba.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for EMC1442 which is compatible with EMC1402.
Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
Reviewed-by: Patrick Williams <patrick@stwcx.xyz>
Link: https://lore.kernel.org/r/20231102090808.427351-1-Delphine_CC_Chiu@wiwynn.com
[groeck: compatible with EMC1402, not EMC1403]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Remove device reference from struct ltc2991_state since it is used only
inside the init function.
Pass the struct device as parameter to the init function instead.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20231031095647.48376-1-antoniu.miclaus@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding Pulse Width Modulation (PWM) and fan tacho NPCM8xx support to
NPCM PWM and fan tacho driver.
NPCM8xx uses a different number of PWM devices.
As part of adding NPCM8XX support:
- Add NPCM8xx specific compatible string.
- Add data to handle architecture-specific PWM parameters.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Link: https://lore.kernel.org/r/20231031075806.400872-2-tmaimon77@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It seems that when the driver is built-in, the HID bus is
initialized after the driver is loaded, which whould cause
module_hid_driver() to fail.
Fix this by registering the driver after the HID bus using
late_initcall() in accordance with other hwmon HID drivers.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20231207210723.222552-1-W_Armin@gmx.de
[groeck: Dropped "compile tested" comment; the patch has been tested
but the tester did not provide a Tested-by: tag]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ACPI specification says:
"If an error occurs while obtaining the meter reading or if the value
is not available then an Integer with all bits set is returned"
Since the "integer" is 32 bits in case of the ACPI power meter,
userspace will get a power reading of 2^32 * 1000 miliwatts (~4.29 MW)
in case of such an error. This was discovered due to a lm_sensors
bugreport (https://github.com/lm-sensors/lm-sensors/issues/460).
Fix this by returning -ENODATA instead.
Tested-by: <urbinek@gmail.com>
Fixes: de584afa5e ("hwmon driver for ACPI 4.0 power meters")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20231124182747.13956-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* New drivers
- Driver for LTC2991
- Driver for POWER-Z
* Added chip / system support to existing drivers
- The ina238 driver now also supports INA237
- The asus-ec-sensors driver now supports ROG Crosshair X670E Gene
- The aquacomputer_d5next now supports Aquacomputer High Flow USB and MPS Flow
- The pmbus/mpq7932 driver now also supports MPQ2286
- The nct6683 now also supports ASRock X670E Taichi
* Various other minor improvements and fixes
- One patch series to call out is the conversion of hwmon platform
drivers to use the platform remove callback returning void
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEiHPvMQj9QTOCiqgVyx8mb86fmYEFAmU/vmUACgkQyx8mb86f
mYEgMw/+LPsHi/uo6y4xfScVChU4zeIY8mhuCwxQXLnVH2tjkwovZ4MwPMV4sFjb
Mwr/IwJKBa8AkelL8xkQy9dMiCsFs9q4CB2ZCY94A41O6Mwra/ILT2YFsk/CIKOw
bZgEViVpeJSjcKGcdzrHkoEC/WuLSR9iul0P+ZC88h1ixUV21+EoJUfGo/a5RC4n
xS1WgbJyFxx+S+VjWDHigJRcGOuGlg1j+25nWjcLr59Qv3COLF3CF9V7w4DM7PAH
zVBO1UCUSLyVjtPZruLEs2yxfYre+apBomqCenBdYOwBJulCLvLm3SnLPo8Ee4rk
9TBiEpqALxvjRnbxfk8VzI7oSLbH5zwOko9PAH7e9sXrhEARXhPWI+8lkXqE8wrc
3I8uv115XOp/Yfo29xF+A4xLJVNRhU6MLieN7afY3YuDipND1gtSAoh8qyqJunf7
dwXDowIlWF+SUmwsxWXxgpKJYVeYzAJYheNKvaIapnCmB/oPKs2dHcwJAqp/voDs
4odnxkhuBBgKpGqqj5C9RKcKdOsku8O9PYBnTMb2IOsimRQg20QTnKn/esfMdK1U
gJBQf/Motg3o3cw5gR/YKb7LdRuxAtxVgrbpwqN9gS/ppCmekgK+o3+4feTN+WAg
746rdIDO88gQIDRuRu+VZOSmXrSOMUFqgLvouyUfwnS6sXdy8Vo=
=8mxv
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New drivers:
- Driver for LTC2991
- Driver for POWER-Z
Added chip / system support to existing drivers:
- The ina238 driver now also supports INA237
- The asus-ec-sensors driver now supports ROG Crosshair X670E Gene
- The aquacomputer_d5next now supports Aquacomputer High Flow USB and
MPS Flow
- The pmbus/mpq7932 driver now also supports MPQ2286
- The nct6683 now also supports ASRock X670E Taichi
Various other minor improvements and fixes:
- One patch series to call out is the conversion of hwmon platform
drivers to use the platform remove callback returning void"
* tag 'hwmon-for-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (69 commits)
hwmon: (aquacomputer_d5next) Check if temp sensors of legacy devices are connected
hwmon: (aquacomputer_d5next) Add support for Aquacomputer High Flow USB and MPS Flow
dt-bindings: hwmon: npcm: Add npcm845 compatible string
hwmon: Add driver for ltc2991
dt-bindings: hwmon: ltc2991: add bindings
hwmon: (pmbus/max31785) Add delay between bus accesses
hwmon: (ina238) add ina237 support
dt-bindings: hwmon: ti,ina2xx: add ti,ina237
hwmon: (asus-ec-sensors) add ROG Crosshair X670E Gene.
hwmon: (max31827) handle vref regulator
hwmon: (ina3221) Add support for channel summation disable
dt-bindings: hwmon: ina3221: Add ti,summation-disable
dt-bindings: hwmon: ina3221: Convert to json-schema
hwmon: (pmbus/mpq7932) Add a support for mpq2286 Power Management IC
hwmon: (pmbus/core) Add helper macro to define single pmbus regulator
regulator: dt-bindings: Add mps,mpq2286 power-management IC
hwmon: (pmbus/mpq7932) Get page count based on chip info
dt-bindings: hwmon: Add possible new properties to max31827 bindings
hwmon: (max31827) Modify conversion wait time
hwmon: (max31827) Make code cleaner
...
- Add symbol definitions related to CDAT to the ACPICA code (Dave
Jiang).
- Use the acpi_device_is_present() helper in more places and rename
acpi_scan_device_not_present() to be about enumeration (James Morse).
- Add __printf format attribute to acpi_os_vprintf() (Su Hui).
- Clean up departures from kernel coding style in the low-level
interface for ACPICA (Jonathan Bergh).
- Replace strncpy() with strscpy() in acpi_osi_setup() (Justin Stitt).
- Fail FPDT parsing on zero length records and add proper handling for
fpdt_process_subtable() to acpi_init_fpdt() (Vasily Khoruzhick).
- Rework acpi_handle_list handling so as to manage it dynamically,
including size computation (Rafael Wysocki).
- Clean up ACPI utilities code so as to make it follow the kernel
coding style (Jonathan Bergh).
- Consolidate IRQ trigger-type override DMI tables and drop .ident
values from dmi_system_id tables used for ACPI resources management
quirks (Hans de Goede).
- Add ACPI IRQ override for TongFang GMxXGxx (Werner Sembach).
- Allow _DSD buffer data only for byte accessors and document the _DSD
data buffer GUID (Andy Shevchenko).
- Drop BayTrail and Lynxpoint pinctrl device IDs from the ACPI LPSS
driver, because it does not need them (Raag Jadav).
- Add acpi_backlight=vendor quirk for Toshiba Portégé R100 (Ondrej
Zary).
- Add "vendor" backlight quirks for 3 Lenovo x86 Android tablets (Hans
de Goede).
- Move Xiaomi Mi Pad 2 backlight quirk to its own section (Hans de
Goede).
- Annotate struct prm_module_info with __counted_by (Kees Cook).
- Fix AER info corruption in aer_recover_queue() when error status data
has multiple sections (Shiju Jose).
- Make APEI use ERST maximum execution time for slow devices (Jeshua
Smith).
- Add support for platform notification handling to the PCC mailbox
driver and modify it to support shared interrupts for multiple
subspaces (Huisong Li).
- Define common macros to use when referring to various bitfields in the
PCC generic communications channel command and status fields and use
them in some drivers (Sudeep Holla).
- Add EC GPE detection quirk for HP 250 G7 Notebook PC (Jonathan
Denose).
- Fix and clean up create_pnp_modalias() and create_of_modalias()
(Christophe JAILLET).
- Modify 2 pieces of code to use acpi_evaluate_dsm_typed() (Andy
Shevchenko).
- Define acpi_dev_uid_match() for matching _UID and use it in several
places (Raag Jadav).
- Use acpi_device_uid() for fetching _UID in 2 places (Raag Jadav).
- Add context argument to acpi_dev_install_notify_handler() (Rafael
Wysocki).
- Clarify ACPI bus concepts in the ACPI device enumeration
documentation (Rafael Wysocki).
- Switch over the ACPI AC and ACPI PAD drivers to using the platform
driver interface which, is more logically consistent than binding a
driver directly to an ACPI device object, and clean them up (Michal
Wilczynski).
- Replace strncpy() in the PNP code with either memcpy() or strscpy()
as appropriate (Justin Stitt).
- Clean up coding style in pnp.h (GuoHua Cheng).
-----BEGIN PGP SIGNATURE-----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=p4Yo
-----END PGP SIGNATURE-----
Merge tag 'acpi-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These fix issues, add new quirks, rearrange the IRQ override quirk
definitions, add new helpers and switch over code to using them,
rework a couple of interfaces to be more flexible, eliminate strncpy()
usage from PNP, extend the ACPI PCC mailbox driver and clean up code.
This is based on ACPI thermal driver changes that are present in the
thermal control updates for 6.7-rc1 pull request (they are depended on
by the ACPI utilities updates). However, the ACPI thermal driver
changes are not included in the list of specific ACPI changes below.
Specifics:
- Add symbol definitions related to CDAT to the ACPICA code (Dave
Jiang)
- Use the acpi_device_is_present() helper in more places and rename
acpi_scan_device_not_present() to be about enumeration (James
Morse)
- Add __printf format attribute to acpi_os_vprintf() (Su Hui)
- Clean up departures from kernel coding style in the low-level
interface for ACPICA (Jonathan Bergh)
- Replace strncpy() with strscpy() in acpi_osi_setup() (Justin Stitt)
- Fail FPDT parsing on zero length records and add proper handling
for fpdt_process_subtable() to acpi_init_fpdt() (Vasily Khoruzhick)
- Rework acpi_handle_list handling so as to manage it dynamically,
including size computation (Rafael Wysocki)
- Clean up ACPI utilities code so as to make it follow the kernel
coding style (Jonathan Bergh)
- Consolidate IRQ trigger-type override DMI tables and drop .ident
values from dmi_system_id tables used for ACPI resources management
quirks (Hans de Goede)
- Add ACPI IRQ override for TongFang GMxXGxx (Werner Sembach)
- Allow _DSD buffer data only for byte accessors and document the
_DSD data buffer GUID (Andy Shevchenko)
- Drop BayTrail and Lynxpoint pinctrl device IDs from the ACPI LPSS
driver, because it does not need them (Raag Jadav)
- Add acpi_backlight=vendor quirk for Toshiba Portégé R100 (Ondrej
Zary)
- Add "vendor" backlight quirks for 3 Lenovo x86 Android tablets
(Hans de Goede)
- Move Xiaomi Mi Pad 2 backlight quirk to its own section (Hans de
Goede)
- Annotate struct prm_module_info with __counted_by (Kees Cook)
- Fix AER info corruption in aer_recover_queue() when error status
data has multiple sections (Shiju Jose)
- Make APEI use ERST maximum execution time for slow devices (Jeshua
Smith)
- Add support for platform notification handling to the PCC mailbox
driver and modify it to support shared interrupts for multiple
subspaces (Huisong Li)
- Define common macros to use when referring to various bitfields in
the PCC generic communications channel command and status fields
and use them in some drivers (Sudeep Holla)
- Add EC GPE detection quirk for HP 250 G7 Notebook PC (Jonathan
Denose)
- Fix and clean up create_pnp_modalias() and create_of_modalias()
(Christophe JAILLET)
- Modify 2 pieces of code to use acpi_evaluate_dsm_typed() (Andy
Shevchenko)
- Define acpi_dev_uid_match() for matching _UID and use it in several
places (Raag Jadav)
- Use acpi_device_uid() for fetching _UID in 2 places (Raag Jadav)
- Add context argument to acpi_dev_install_notify_handler() (Rafael
Wysocki)
- Clarify ACPI bus concepts in the ACPI device enumeration
documentation (Rafael Wysocki)
- Switch over the ACPI AC and ACPI PAD drivers to using the platform
driver interface which, is more logically consistent than binding a
driver directly to an ACPI device object, and clean them up (Michal
Wilczynski)
- Replace strncpy() in the PNP code with either memcpy() or strscpy()
as appropriate (Justin Stitt)
- Clean up coding style in pnp.h (GuoHua Cheng)"
* tag 'acpi-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (54 commits)
ACPI: resource: Do IRQ override on TongFang GMxXGxx
perf: arm_cspmu: use acpi_dev_hid_uid_match() for matching _HID and _UID
ACPI: EC: Add quirk for HP 250 G7 Notebook PC
ACPI: x86: use acpi_dev_uid_match() for matching _UID
ACPI: utils: use acpi_dev_uid_match() for matching _UID
pinctrl: intel: use acpi_dev_uid_match() for matching _UID
ACPI: utils: Introduce acpi_dev_uid_match() for matching _UID
ACPI: sysfs: Clean up create_pnp_modalias() and create_of_modalias()
ACPI: sysfs: Fix create_pnp_modalias() and create_of_modalias()
ACPI: acpi_pad: Rename ACPI device from device to adev
ACPI: acpi_pad: Use dev groups for sysfs
ACPI: acpi_pad: Replace acpi_driver with platform_driver
ACPI: APEI: Use ERST timeout for slow devices
ACPI: scan: Rename acpi_scan_device_not_present() to be about enumeration
PNP: replace deprecated strncpy() with memcpy()
PNP: ACPI: replace deprecated strncpy() with strscpy()
perf: qcom: use acpi_device_uid() for fetching _UID
ACPI: sysfs: use acpi_device_uid() for fetching _UID
ACPI: scan: Use the acpi_device_is_present() helper in more places
ACPI: AC: Rename ACPI device from device to adev
...
- Add LKDTM test for stuck CPUs (Mark Rutland)
- Improve LKDTM selftest behavior under UBSan (Ricardo Cañuelo)
- Refactor more 1-element arrays into flexible arrays (Gustavo A. R. Silva)
- Analyze and replace strlcpy and strncpy uses (Justin Stitt, Azeem Shaikh)
- Convert group_info.usage to refcount_t (Elena Reshetova)
- Add __counted_by annotations (Kees Cook, Gustavo A. R. Silva)
- Add Kconfig fragment for basic hardening options (Kees Cook, Lukas Bulwahn)
- Fix randstruct GCC plugin performance mode to stay in groups (Kees Cook)
- Fix strtomem() compile-time check for small sources (Kees Cook)
-----BEGIN PGP SIGNATURE-----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=0iVF
-----END PGP SIGNATURE-----
Merge tag 'hardening-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening updates from Kees Cook:
"One of the more voluminous set of changes is for adding the new
__counted_by annotation[1] to gain run-time bounds checking of
dynamically sized arrays with UBSan.
- Add LKDTM test for stuck CPUs (Mark Rutland)
- Improve LKDTM selftest behavior under UBSan (Ricardo Cañuelo)
- Refactor more 1-element arrays into flexible arrays (Gustavo A. R.
Silva)
- Analyze and replace strlcpy and strncpy uses (Justin Stitt, Azeem
Shaikh)
- Convert group_info.usage to refcount_t (Elena Reshetova)
- Add __counted_by annotations (Kees Cook, Gustavo A. R. Silva)
- Add Kconfig fragment for basic hardening options (Kees Cook, Lukas
Bulwahn)
- Fix randstruct GCC plugin performance mode to stay in groups (Kees
Cook)
- Fix strtomem() compile-time check for small sources (Kees Cook)"
* tag 'hardening-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (56 commits)
hwmon: (acpi_power_meter) replace open-coded kmemdup_nul
reset: Annotate struct reset_control_array with __counted_by
kexec: Annotate struct crash_mem with __counted_by
virtio_console: Annotate struct port_buffer with __counted_by
ima: Add __counted_by for struct modsig and use struct_size()
MAINTAINERS: Include stackleak paths in hardening entry
string: Adjust strtomem() logic to allow for smaller sources
hardening: x86: drop reference to removed config AMD_IOMMU_V2
randstruct: Fix gcc-plugin performance mode to stay in group
mailbox: zynqmp: Annotate struct zynqmp_ipi_pdata with __counted_by
drivers: thermal: tsens: Annotate struct tsens_priv with __counted_by
irqchip/imx-intmux: Annotate struct intmux_data with __counted_by
KVM: Annotate struct kvm_irq_routing_table with __counted_by
virt: acrn: Annotate struct vm_memory_region_batch with __counted_by
hwmon: Annotate struct gsc_hwmon_platform_data with __counted_by
sparc: Annotate struct cpuinfo_tree with __counted_by
isdn: kcapi: replace deprecated strncpy with strscpy_pad
isdn: replace deprecated strncpy with strscpy
NFS/flexfiles: Annotate struct nfs4_ff_layout_segment with __counted_by
nfs41: Annotate struct nfs4_file_layout_dsaddr with __counted_by
...
- Limit the hardcoded topology quirk for Hygon CPUs to those which have a
model ID less than 4. The newer models have the topology CPUID leaf 0xB
correctly implemented and are not affected.
- Make SMT control more robust against enumeration failures
SMT control was added to allow controlling SMT at boottime or
runtime. The primary purpose was to provide a simple mechanism to
disable SMT in the light of speculation attack vectors.
It turned out that the code is sensible to enumeration failures and
worked only by chance for XEN/PV. XEN/PV has no real APIC enumeration
which means the primary thread mask is not set up correctly. By chance
a XEN/PV boot ends up with smp_num_siblings == 2, which makes the
hotplug control stay at its default value "enabled". So the mask is
never evaluated.
The ongoing rework of the topology evaluation caused XEN/PV to end up
with smp_num_siblings == 1, which sets the SMT control to "not
supported" and the empty primary thread mask causes the hotplug core to
deny the bringup of the APS.
Make the decision logic more robust and take 'not supported' and 'not
implemented' into account for the decision whether a CPU should be
booted or not.
- Fake primary thread mask for XEN/PV
Pretend that all XEN/PV vCPUs are primary threads, which makes the
usage of the primary thread mask valid on XEN/PV. That is consistent
with because all of the topology information on XEN/PV is fake or even
non-existent.
- Encapsulate topology information in cpuinfo_x86
Move the randomly scattered topology data into a separate data
structure for readability and as a preparatory step for the topology
evaluation overhaul.
- Consolidate APIC ID data type to u32
It's fixed width hardware data and not randomly u16, int, unsigned long
or whatever developers decided to use.
- Cure the abuse of cpuinfo for persisting logical IDs.
Per CPU cpuinfo is used to persist the logical package and die
IDs. That's really not the right place simply because cpuinfo is
subject to be reinitialized when a CPU goes through an offline/online
cycle.
Use separate per CPU data for the persisting to enable the further
topology management rework. It will be removed once the new topology
management is in place.
- Provide a debug interface for inspecting topology information
Useful in general and extremly helpful for validating the topology
management rework in terms of correctness or "bug" compatibility.
-----BEGIN PGP SIGNATURE-----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=xrz8
-----END PGP SIGNATURE-----
Merge tag 'x86-core-2023-10-29-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 core updates from Thomas Gleixner:
- Limit the hardcoded topology quirk for Hygon CPUs to those which have
a model ID less than 4.
The newer models have the topology CPUID leaf 0xB correctly
implemented and are not affected.
- Make SMT control more robust against enumeration failures
SMT control was added to allow controlling SMT at boottime or
runtime. The primary purpose was to provide a simple mechanism to
disable SMT in the light of speculation attack vectors.
It turned out that the code is sensible to enumeration failures and
worked only by chance for XEN/PV. XEN/PV has no real APIC enumeration
which means the primary thread mask is not set up correctly. By
chance a XEN/PV boot ends up with smp_num_siblings == 2, which makes
the hotplug control stay at its default value "enabled". So the mask
is never evaluated.
The ongoing rework of the topology evaluation caused XEN/PV to end up
with smp_num_siblings == 1, which sets the SMT control to "not
supported" and the empty primary thread mask causes the hotplug core
to deny the bringup of the APS.
Make the decision logic more robust and take 'not supported' and 'not
implemented' into account for the decision whether a CPU should be
booted or not.
- Fake primary thread mask for XEN/PV
Pretend that all XEN/PV vCPUs are primary threads, which makes the
usage of the primary thread mask valid on XEN/PV. That is consistent
with because all of the topology information on XEN/PV is fake or
even non-existent.
- Encapsulate topology information in cpuinfo_x86
Move the randomly scattered topology data into a separate data
structure for readability and as a preparatory step for the topology
evaluation overhaul.
- Consolidate APIC ID data type to u32
It's fixed width hardware data and not randomly u16, int, unsigned
long or whatever developers decided to use.
- Cure the abuse of cpuinfo for persisting logical IDs.
Per CPU cpuinfo is used to persist the logical package and die IDs.
That's really not the right place simply because cpuinfo is subject
to be reinitialized when a CPU goes through an offline/online cycle.
Use separate per CPU data for the persisting to enable the further
topology management rework. It will be removed once the new topology
management is in place.
- Provide a debug interface for inspecting topology information
Useful in general and extremly helpful for validating the topology
management rework in terms of correctness or "bug" compatibility.
* tag 'x86-core-2023-10-29-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
x86/apic, x86/hyperv: Use u32 in hv_snp_boot_ap() too
x86/cpu: Provide debug interface
x86/cpu/topology: Cure the abuse of cpuinfo for persisting logical ids
x86/apic: Use u32 for wakeup_secondary_cpu[_64]()
x86/apic: Use u32 for [gs]et_apic_id()
x86/apic: Use u32 for phys_pkg_id()
x86/apic: Use u32 for cpu_present_to_apicid()
x86/apic: Use u32 for check_apicid_used()
x86/apic: Use u32 for APIC IDs in global data
x86/apic: Use BAD_APICID consistently
x86/cpu: Move cpu_l[l2]c_id into topology info
x86/cpu: Move logical package and die IDs into topology info
x86/cpu: Remove pointless evaluation of x86_coreid_bits
x86/cpu: Move cu_id into topology info
x86/cpu: Move cpu_core_id into topology info
hwmon: (fam15h_power) Use topology_core_id()
scsi: lpfc: Use topology_core_id()
x86/cpu: Move cpu_die_id into topology info
x86/cpu: Move phys_proc_id into topology info
x86/cpu: Encapsulate topology information in cpuinfo_x86
...
Return -ENODATA if a temp sensor of a legacy device
does not contain a reading.
Originally-from: Leonard Anderweit <leonard.anderweit@gmail.com>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20231016083559.139341-2-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose various hardware sensors of the
Aquacomputer High Flow USB flow sensor, which communicates through a
proprietary USB HID protocol. This commit also adds support for the sensors
of the MPS Flow devices, as they have the same USB product ID and sensor
layouts. Implemented by Leonard Anderweit [1].
Internal and external temp sensor readings are available, along with
the flow sensor.
Additionally, serial number and firmware version are exposed through
debugfs.
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/90
Originally-from: Leonard Anderweit <leonard.anderweit@gmail.com>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20231016083559.139341-3-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for LTC2991 Octal I2C Voltage, Current, and Temperature
Monitor.
The LTC2991 is used to monitor system temperatures, voltages and
currents. Through the I2C serial interface, the eight monitors can
individually measure supply voltages and can be paired for
differential measurements of current sense resistors or temperature
sensing transistors. Additional measurements include internal
temperature and internal VCC.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20231026103413.27800-2-antoniu.miclaus@analog.com
[groeck: Fixed up documentation warning]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The MAX31785 has shown erratic behaviour across multiple system
designs, unexpectedly clock stretching and NAKing transactions.
Experimentation shows that this seems to be triggered by a register access
directly back to back with a previous register write. Experimentation also
shows that inserting a small delay after register writes makes the issue go
away.
Use a similar solution to what the max15301 driver does to solve the same
problem. Create a custom set of bus read and write functions that make sure
that the delay is added.
Signed-off-by: Lakshmi Yadlapati <lakshmiy@us.ibm.com>
Link: https://lore.kernel.org/r/20231027044346.2167548-1-lakshmiy@us.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The INA237 "85-V, 16-Bit, Precision Power Monitor With I2C Interface" is
basically the same as INA328. Therefore add a corresponding compatible
to the driver.
According to the datasheet the main difference is the current and power
monitoring accuracy:
+------------------------+---------------+---------------+
| | INA238 | INA237 |
+------------------------+---------------+---------------+
| Offset voltage | +/- 5µV | +/- 50µV |
| Offset drift | +/- 0.02µV/°C | +/- 0.02µV/°C |
| Gain error | +/- 0.1% | +/- 0.3% |
| Gain error drift | +/- 25ppm/°C | +/- 50ppm/°C |
| Common mode rejection | 140dB | 120dB |
| Power accuracy | 0.7% | 1.6% |
+------------------------+---------------+---------------+
As well as the missing DEVICE_ID register at 0x3F, which is currently
not in use by the driver.
Signed-off-by: Richard Leitner <richard.leitner@linux.dev>
Link: https://lore.kernel.org/r/20231026-ina237-v2-1-dec44811a3c9@linux.dev
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Only the temp sensors that I can verify are present.
T_Sensor is the temperature reading of a 10kΩ β=3435K NTC thermistor
optionally connected to the T_SENSOR header.
The other sensors are as found on the X670E Hero.
Signed-off-by: Ellie Hermaszewska <kernel@monoid.al>
Link: https://lore.kernel.org/r/20231026104332.906357-1-kernel@monoid.al
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add missing implementation for the max31827 supply regulator.
This is a hardware required property that is not handled.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20230925122929.10610-1-antoniu.miclaus@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The INA3221 allows the Critical alert pin to be controlled by the
summation control function. This function adds the single
shunt-voltage conversions for the desired channels in order to compare
the combined sum to the programmed limit. The Shunt-Voltage Sum Limit
register contains the programmed value that is compared to the value in
the Shunt-Voltage Sum register in order to determine if the total summed
limit is exceeded. If the shunt-voltage sum limit value is exceeded, the
Critical alert pin pulls low.
For the summation limit to have a meaningful value, we have to use the
same shunt-resistor value on all included channels. Unless equal
shunt-resistor values are used for each channel, the summation control
function cannot be used and it is not enabled by the driver.
To address this, add support to disable the summation of specific
channels via device tree property "ti,summation-disable". The channel
which has this property would be excluded from the calculation of
summation control function.
For example, summation control function calculates Shunt-Voltage Sum as:
- input_shunt_voltage_summation = input_shunt_voltage_channel1
+ input_shunt_voltage_channel2
+ input_shunt_voltage_channel3
If we want the summation to only use channel1 and channel3, we can add
'ti,summation-disable' property in device tree node for channel2. Then
the calculation will skip channel2.
- input_shunt_voltage_summation = input_shunt_voltage_channel1
+ input_shunt_voltage_channel3
Note that we only want the channel to be skipped for summation control
function rather than completely disabled. Therefore, even if we add the
property 'ti,summation-disable', the channel is still enabled and
functional.
Finally, create debugfs entries that display if summation is disabled
for each of the channels.
Signed-off-by: Rajkumar Kasirajan <rkasirajan@nvidia.com>
Signed-off-by: Ninad Malwade <nmalwade@nvidia.com>
Co-developed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20230929103650.86074-4-jonathanh@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The MPQ2286 is a programmable, high frequency synchronous buck regulator
designed to power a variety of Automotive system peripherals. Single buck
converters with hardware monitoring capability is configurable over PMBus
interface.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
Link: https://lore.kernel.org/r/20231011164754.449399-5-saravanan@linumiz.com
[groeck: Updated subject (mpq2286 -> mpq7932)]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The bindings for single instance regulator should be named with no instance
(e.g., buck not buck0). Introduce a new helper macro to define the single pmbus
regulator.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
Link: https://lore.kernel.org/r/20231011164754.449399-4-saravanan@linumiz.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Get page count using compatible match to support the series of chipsets
which differs in number of regualator/page.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
Link: https://lore.kernel.org/r/20231011164754.449399-2-saravanan@linumiz.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There is nothing in the datasheet indicating that the 1ms error is
needed and I didn't encounter any error during testing with 140ms wait
time.
Signed-off-by: Daniel Matyas <daniel.matyas@analog.com>
Link: https://lore.kernel.org/r/20230919093456.10592-2-daniel.matyas@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Used enums and while loops to replace switch for selecting and getting
update interval from conversion rate bits.
Divided the write_alarm_val function into 2 functions. The new function
is more generic: it can be used not only for alarm writes, but for any
kind of writes which require the device to be in shutdown mode.
Signed-off-by: Daniel Matyas <daniel.matyas@analog.com>
Link: https://lore.kernel.org/r/20230919093456.10592-1-daniel.matyas@analog.com
[groeck: Reverted error return value change (EOPNOTSUPP -> EINVAL)]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Do not allow setting shunt resistor to 0. This results in a division by
zero when performing current value computations based on input voltages
and connected resistor values.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20231011135754.13508-1-antoniu.miclaus@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
npcm7xx_pwm_config_set() can return '-ENODEV' for failed. So check
the value of 'ret' after calling npcm7xx_pwm_config_set().
Signed-off-by: Su Hui <suhui@nfschina.com>
Link: https://lore.kernel.org/r/20231020085518.198477-1-suhui@nfschina.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently the local variable hum is being divided by a constant and
the results is being re-assigned back to hum before the value is being
returned to the caller. The assignment to hum is redundant and can
be removed.
Cleans up clang scan build warning:
drivers/hwmon/hs3001.c:65:9: warning: Although the value stored to 'hum'
is used in the enclosing expression, the value is never actually read
from 'hum' [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20231023135828.667297-1-colin.i.king@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the ADT7490's Imon voltage readout. It is handled
largely the same way as the existing Vtt readout.
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Co-developed-by: Shawn Anastasio <sanastasio@raptorengineering.com>
Signed-off-by: Shawn Anastasio <sanastasio@raptorengineering.com>
Link: https://lore.kernel.org/r/20230914223947.829025-1-tpearson@raptorengineering.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918085951.1234172-25-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918085951.1234172-24-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918085951.1234172-23-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918085951.1234172-22-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918085951.1234172-21-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918085951.1234172-20-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918085951.1234172-19-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918085951.1234172-18-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918085951.1234172-17-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918085951.1234172-16-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918085951.1234172-15-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918085951.1234172-14-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918085951.1234172-13-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918085951.1234172-12-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918085951.1234172-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918085951.1234172-10-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918085951.1234172-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918085951.1234172-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918085951.1234172-7-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918085951.1234172-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918085951.1234172-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918085951.1234172-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230918085951.1234172-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The two drivers compile fine on arm64, powerpc, m68k and s390. So make
it possible to enable the drivers in the presence of COMPILE_TEST.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230918085951.1234172-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After some testing on a Fujitsu Esprimo P720, it turned out that
the limit registers are indeed writable and affect the fan control
algorithm. This is supported by the datasheet, which says that the
fan control functions are based on the limit and parameter registers.
Since accessing those registers is very inefficient, the existing
regmap cache is used to cache those registers values.
Tested on a Fujitsu Esprimo P720.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230907052639.16491-5-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Accessing virtual registers is very inefficient, so pwm map values
should be cached when possible, else userspace could effectively do
a DOS attack by reading pwm map values in a while loop.
Use the regmap cache to cache those values.
Tested on a Fujitsu Esprimo P720.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230907052639.16491-4-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When the lock bit inside SCH5627_REG_CTRL is set, then the virtual
registers become read-only until the next power cycle.
Disallow write access to those registers in such a case.
Tested on a Fujitsu Esprimo P720.
Fixes: aa9f833dfc ("hwmon: (sch5627) Add pwmX_auto_channels_temp support")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230907052639.16491-3-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use bit macros then accessing SCH5627_REG_CTRL, so that people
do not need to look at the datasheet to find out what each bit
does.
Tested on a Fujitsu Esprimo P720.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230907052639.16491-2-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Simplify tmp51x_read_properties() by replacing 'nfactor' ->'data->nfactor'
in device_property_read_u32_array() and drop the local variable as it is
unused.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230907071404.24334-3-biju.das.jz@bp.renesas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The tmp512 chip has 3 channels whereas tmp513 has 4 channels. Avoid
using tmp51x_ids for this HW difference by replacing OF/ID table
data with maximum channels supported by the device.
Replace id->max_channels variable from struct tmp51x_data and drop the
macros TMP51{2,3}_TEMP_CONFIG_DEFAULT as it can be derived from the macro
TMP51X_TEMP_CONFIG_DEFAULT and update the logic in tmp51x_is_visible(),
tmp51x_read_properties() and tmp51x_init() using max_channels.
While at it, drop enum tmp51x_ids as there is no user and remove
trailing comma in the terminator entry for OF table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230907071404.24334-2-biju.das.jz@bp.renesas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TDA38640 can operate in either PMBus mode or SVID mode.
In SVID mode, by design ENABLE pin is the only option for controlling
the output rail i.e., ENABLE pin is chained to power good of another
reglator & FPGA.
In cases where the chip is configured for SVID mode, and the ENABLE pin
is set at a fixed level or is left unconnected (with an internal
pull-down), while requiring software control, the following
workaround is necessary.
The workaround utilizes ENABLE pin polarity flipping to control
output rail.
If property 'infineon,en-pin-fixed-level' is specified then
determine if chip is in SVID mode by checking BIT15 of MTP memory offset
0x44 as described in the datasheet.
If chip is in SVID mode then apply the workaround by
1. Determine EN pin level
2. Maps BIT7 of OPERATION(01h) to EN_PIN_POLARITY(BIT1) of
PB_ON_OFF_CONFIG.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20230831190731.265099-3-Naresh.Solanki@9elements.com
[groeck: Dropped unnecessary line continuation]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
POWER-Z is a series of devices to monitor power characteristics of
USB-C connections and display those on a on-device display.
Some of the devices, notably KM002C and KM003C, contain an additional
port which exposes the measurements via USB.
This is a driver for this monitor port.
It was developed and tested with the KM003C.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20230902-powerz-v4-1-7ec2c1440687@weissschuh.net
[groeck:
Release urb after hwmon registration error;
Move priv->status initialization to correct place before reinit_completion
]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This reverts commit 393935baa4.
As reported by Ian Nartowicz, this and the next patch
result in a failure to load the driver on Celsius W280.
While the alternative would be to add the board to the DMI
override table, it is quite likely that other systems are
also affected. Revert the offending patches to avoid future
problems.
Fixes: 393935baa4 ("hwmon: (sch56xx-common) Add automatic module loading on supported devices")
Reported-by: Ian Nartowicz <deadbeef@nartowicz.co.uk>
Closes: https://lore.kernel.org/linux-hwmon/20231025192239.3c5389ae@debian.org/T/#t
Cc: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This reverts commit fd2d53c367.
As reported by Ian Nartowicz, this and the preceding patch
result in a failure to load the driver on Celsius W280.
While the alternative would be to add the board to the DMI
override table, it is quite likely that other systems are
also affected. Revert the offending patches to avoid future
problems.
Fixes: fd2d53c367 ("hwmon: (sch56xx-common) Add DMI override table")
Reported-by: Ian Nartowicz <deadbeef@nartowicz.co.uk>
Closes: https://lore.kernel.org/linux-hwmon/20231025192239.3c5389ae@debian.org/T/#t
Cc: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In the regmap conversion in commit 4ef2774511 ("hwmon: (nct6775)
Convert register access to regmap API") I reused the 'reg' variable
for all three register reads in the fan speed calculation loop in
nct6775_update_device(), but failed to notice that the value from the
first one (data->REG_FAN[i]) is actually used in the call to
nct6775_select_fan_div() at the end of the loop body. Since that
patch the register value passed to nct6775_select_fan_div() has been
(conditionally) incorrectly clobbered with the value of a different
register than intended, which has in at least some cases resulted in
fan speeds being adjusted down to zero.
Fix this by using dedicated temporaries for the two intermediate
register reads instead of 'reg'.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 4ef2774511 ("hwmon: (nct6775) Convert register access to regmap API")
Reported-by: Thomas Zajic <zlatko@gmx.at>
Tested-by: Thomas Zajic <zlatko@gmx.at>
Cc: stable@vger.kernel.org # v5.19+
Link: https://lore.kernel.org/r/20230929200822.964-2-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When build with W=1 and "-Werror=format-truncation", below error is
observed in coretemp driver,
drivers/hwmon/coretemp.c: In function 'create_core_data':
>> drivers/hwmon/coretemp.c:393:34: error: '%s' directive output may be truncated writing likely 5 or more bytes into a region of size between 3 and 13 [-Werror=format-truncation=]
393 | "temp%d_%s", attr_no, suffixes[i]);
| ^~
drivers/hwmon/coretemp.c:393:26: note: assuming directive output of 5 bytes
393 | "temp%d_%s", attr_no, suffixes[i]);
| ^~~~~~~~~~~
drivers/hwmon/coretemp.c:392:17: note: 'snprintf' output 7 or more bytes (assuming 22) into a destination of size 19
392 | snprintf(tdata->attr_name[i], CORETEMP_NAME_LENGTH,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
393 | "temp%d_%s", attr_no, suffixes[i]);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Given that
1. '%d' could take 10 charactors,
2. '%s' could take 10 charactors ("crit_alarm"),
3. "temp", "_" and the NULL terminator take 6 charactors,
fix the problem by increasing CORETEMP_NAME_LENGTH to 28.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Fixes: 7108b80a54 ("hwmon/coretemp: Handle large core ID value")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310200443.iD3tUbbK-lkp@intel.com/
Link: https://lore.kernel.org/r/20231025122316.836400-1-rui.zhang@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
axi_fan_control_irq_handler(), dependent on the private
axi_fan_control_data structure, might be called before the hwmon
device is registered. That will cause an "Unable to handle kernel
NULL pointer dereference" error.
Fixes: 8412b410fa ("hwmon: Support ADI Fan Control IP")
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20231025132100.649499-1-nuno.sa@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Main updates include:
1. Addition of support for Type 4 PCC subspace that enables platform
notification handling (Huisong Li).
2. Support for the shared interrupt amongst multiple PCC subspaces/
channels (Huisong Li).
3. Consolidation of PCC shared memory region command and status
bitfields definitions that were duplicated and scattered across
multiple PCC client drivers (Sudeep Holla).
-----BEGIN PGP SIGNATURE-----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=bZ1a
-----END PGP SIGNATURE-----
Merge tag 'acpi-pcc-updates-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux
Merge ACPI PCC changes for v6.7 from Sudeep Holla:
"ACPI: PCC: Mailbox and generic updates for v6.7
Main updates include:
1. Addition of support for Type 4 PCC subspace that enables platform
notification handling (Huisong Li).
2. Support for the shared interrupt amongst multiple PCC subspaces/
channels (Huisong Li).
3. Consolidation of PCC shared memory region command and status
bitfields definitions that were duplicated and scattered across
multiple PCC client drivers (Sudeep Holla)."
* tag 'acpi-pcc-updates-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
soc: kunpeng_hccs: Migrate to use generic PCC shmem related macros
hwmon: (xgene) Migrate to use generic PCC shmem related macros
i2c: xgene-slimpro: Migrate to use generic PCC shmem related macros
ACPI: PCC: Add PCC shared memory region command and status bitfields
mailbox: pcc: Support shared interrupt for multiple subspaces
mailbox: pcc: Add support for platform notification handling
Use the newly defined common and generic PCC shared memory region
related macros in this driver to replace the locally defined ones.
Cc: Jean Delvare <jdelvare@suse.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230927-pcc_defines-v2-3-0b8ffeaef2e5@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Here is the big set of char/misc and other small driver subsystem
changes for 6.6-rc1.
Stuff all over the place here, lots of driver updates and changes and
new additions. Short summary is:
- new IIO drivers and updates
- Interconnect driver updates
- fpga driver updates and additions
- fsi driver updates
- mei driver updates
- coresight driver updates
- nvmem driver updates
- counter driver updates
- lots of smaller misc and char driver updates and additions
All of these have been in linux-next for a long time with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPH64g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynr2QCfd3RKeR+WnGzyEOFhksl30UJJhiIAoNZtYT5+
t9KG0iMDXRuTsOqeEQbd
=tVnk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
changes for 6.6-rc1.
Stuff all over the place here, lots of driver updates and changes and
new additions. Short summary is:
- new IIO drivers and updates
- Interconnect driver updates
- fpga driver updates and additions
- fsi driver updates
- mei driver updates
- coresight driver updates
- nvmem driver updates
- counter driver updates
- lots of smaller misc and char driver updates and additions
All of these have been in linux-next for a long time with no reported
problems"
* tag 'char-misc-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (267 commits)
nvmem: core: Notify when a new layout is registered
nvmem: core: Do not open-code existing functions
nvmem: core: Return NULL when no nvmem layout is found
nvmem: core: Create all cells before adding the nvmem device
nvmem: u-boot-env:: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
nvmem: sec-qfprom: Add Qualcomm secure QFPROM support
dt-bindings: nvmem: sec-qfprom: Add bindings for secure qfprom
dt-bindings: nvmem: Add compatible for QCM2290
nvmem: Kconfig: Fix typo "drive" -> "driver"
nvmem: Explicitly include correct DT includes
nvmem: add new NXP QorIQ eFuse driver
dt-bindings: nvmem: Add t1023-sfp efuse support
dt-bindings: nvmem: qfprom: Add compatible for MSM8226
nvmem: uniphier: Use devm_platform_get_and_ioremap_resource()
nvmem: qfprom: do some cleanup
nvmem: stm32-romem: Use devm_platform_get_and_ioremap_resource()
nvmem: rockchip-efuse: Use devm_platform_get_and_ioremap_resource()
nvmem: meson-mx-efuse: Convert to devm_platform_ioremap_resource()
nvmem: lpc18xx_otp: Convert to devm_platform_ioremap_resource()
nvmem: brcm_nvram: Use devm_platform_get_and_ioremap_resource()
...
- New drivers
* Driver for Renesas HS3001
- Chip support added to existing drivers
* pmbus/mp2975 driver now supports MP2971 and MP2973
- Functional improvements
* Additional voltage and temperature sensor support for
NCT6798/NCT6799 in nt6755 driver
* it87 driver now detects AMDTSI sensor type
* dimmtemp now supports more than 32 DIMMs
- Driver removals
* sm665 driver removed as unsupportable and long since obsolete
- Minor fixes, cleanups, and simplifications in several drivers
-----BEGIN PGP SIGNATURE-----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=dpys
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New drivers:
- Renesas HS3001
Chip support added to existing drivers:
- pmbus/mp2975 driver now supports MP2971 and MP2973
Functional improvements:
- Additional voltage and temperature sensor support for
NCT6798/NCT6799 in nt6755 driver
- it87 driver now detects AMDTSI sensor type
- dimmtemp now supports more than 32 DIMMs
Driver removals:
- sm665 driver removed as unsupportable and long since obsolete
.. and minor fixes, cleanups, and simplifications in several drivers"
* tag 'hwmon-for-v6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (57 commits)
hwmon: (tmp513) Simplify probe()
hwmon: (tmp513) Fix the channel number in tmp51x_is_visible()
hwmon: (mlxreg-fan) Extend number of supported fans
hwmon: (sis5595) Do PCI error checks on own line
hwmon: (vt8231) Do PCI error checks on own line
hwmon: (via686a) Do PCI error checks on own line
hwmon: pmbus: Fix -EIO seen on pli1209
hwmon: pmbus: Drop unnecessary clear fault page
hwmon: pmbus: Reduce clear fault page invocations
hwmon: (nsa320-hwmon) Remove redundant of_match_ptr()
hwmon: (pmbus/ucd9200) fix Wvoid-pointer-to-enum-cast warning
hwmon: (pmbus/ucd9000) fix Wvoid-pointer-to-enum-cast warning
hwmon: (pmbus/tps53679) fix Wvoid-pointer-to-enum-cast warning
hwmon: (pmbus/ibm-cffps) fix Wvoid-pointer-to-enum-cast warning
hwmon: (tmp513) fix Wvoid-pointer-to-enum-cast warning
hwmon: (max6697) fix Wvoid-pointer-to-enum-cast warning
hwmon: (max20730) fix Wvoid-pointer-to-enum-cast warning
hwmon: (lm90) fix Wvoid-pointer-to-enum-cast warning
hwmon: (lm85) fix Wvoid-pointer-to-enum-cast warning
hwmon: (lm75) fix Wvoid-pointer-to-enum-cast warning
...
the respective drivers
- Update HPE Superdome Flex maintainers list
-----BEGIN PGP SIGNATURE-----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=e0EQ
-----END PGP SIGNATURE-----
Merge tag 'x86_misc_for_v6.6_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull misc x86 updates from Borislav Petkov:
- Add PCI device IDs for a new AMD family 0x1a CPUs and use them in the
respective drivers
- Update HPE Superdome Flex maintainers list
* tag 'x86_misc_for_v6.6_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/uv: Update HPE Superdome Flex Maintainers
EDAC/amd64: Add support for AMD family 1Ah models 00h-1Fh and 40h-4Fh
hwmon: (k10temp) Add thermal support for AMD Family 1Ah-based models
x86/amd_nb: Add PCI IDs for AMD Family 1Ah-based models
Simpilfy probe() by replacing device_get_match_data() and id lookup for
retrieving match data by i2c_get_match_data().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230824204456.401580-3-biju.das.jz@bp.renesas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some new big modular systems can be equipped with up to 24 fans.
Extend maximum number of fans accordingly.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20230824164006.26868-1-vadimp@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Instead of if conditions with line splits, use the usual error handling
pattern with a separate variable to improve readability. Handle error
print with a label instead of trying to chain everything into a single
if condition.
No functional changes intended.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230824132832.78705-14-ilpo.jarvinen@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Instead of if conditions with line splits, use the usual error handling
pattern with a separate variable to improve readability.
No functional changes intended.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230824132832.78705-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Instead of if conditions with line splits, use the usual error handling
pattern with a separate variable to improve readability.
No functional changes intended.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230824132832.78705-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After doing performance optimizations the pli1209 driver failed to
probe with a probabilty of 2%. It wasn't able to read the PMBUS_OPERATION
register due to an -EIO error.
An investigation showed that the PLI1209 takes 230 usec to execute the
CLEAR_FAULTS command. During that time it's busy and NACKs all requests
on the SMBUS interface. It also NACKs reads on PMBUS_STATUS_BYTE
making it impossible to poll the BUSY flag.
Add a custom write_data function to just wait for not BUSY unconditionally
after sending a CLEAR_FAULTS command.
TEST: Verified using an I2C bus analyser that no more NACKs are seen after
sending a CLEAR_FAULTS command.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20230817092527.808631-3-Naresh.Solanki@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The pmbus_check_byte_register function already calls clear
fault page, so there's no need to do it again in
pmbus_identify_common.
TEST: Verified using an I2C bus analyser to confirm that only
one clear fault page is being send instead of two in a row.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20230817092527.808631-2-Naresh.Solanki@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Observing I2C traffic revealed consecutive transmission of CLEAR_FAULT
commands. While this doesn't cause issues, it extends driver probe time.
Avoid invoking pmbus_clear_fault_page for virtual registers, as they're
managed by the driver, not the chip.
TEST: Verified using an I2C bus analyzer that only one CLEAR_FAULT
command is send instead 5 in a row.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20230817092527.808631-1-Naresh.Solanki@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
'chip' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
ucd9200.c:106:10: error: cast to smaller integer type 'enum chips' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810093157.94244-15-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
'chip' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
ucd9000.c:591:10: error: cast to smaller integer type 'enum chips' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810093157.94244-14-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
'chip_id' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
tps53679.c:238:13: error: cast to smaller integer type 'enum chips' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810093157.94244-13-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
'vs' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
ibm-cffps.c:492:8: error: cast to smaller integer type 'enum versions' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810093157.94244-12-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
'id' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
tmp513.c:724:14: error: cast to smaller integer type 'enum tmp51x_ids' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810093157.94244-11-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
'type' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
max6697.c:705:16: error: cast to smaller integer type 'enum chips' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810093157.94244-10-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
'chip_id' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
max20730.c:719:13: error: cast to smaller integer type 'enum chips' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810093157.94244-9-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
'kind' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
lm90.c:2768:16: error: cast to smaller integer type 'enum chips' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810093157.94244-8-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
'type' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
lm85.c:1562:16: error: cast to smaller integer type 'enum chips' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810093157.94244-7-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
'kind' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
lm75.c:581:10: error: cast to smaller integer type 'enum lm75_type' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810093157.94244-6-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
'kind' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
lm63.c:1108:16: error: cast to smaller integer type 'enum chips' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810093157.94244-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
'chip' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
ina2xx.c:627:10: error: cast to smaller integer type 'enum ina2xx_ids' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810093157.94244-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
'chip' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
ads7828.c:142:10: error: cast to smaller integer type 'enum ads7828_chips' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810093157.94244-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
'type' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
ad7418.c:256:16: error: cast to smaller integer type 'enum chips' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810093157.94244-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
'chip' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
adt7475.c:1655:10: error: cast to smaller integer type 'enum chips' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810093157.94244-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Additional TEMP registers for nct6798d, nct6799d-r and nct6796d-s
This allows the max/max_hyst/crit attributes to be shown/stored
* Increase NUM_TEMP from 10 to 12
* Separate TEMP/MON_TEMP/OVER/HYST/CRIT registers
* Rename "PECI Calibration" to include "TSI" too
* Update ALARM/BEEP bits for temps for 6799
* For 6799, keep temp_fixed_num at 6, but increase
num_temp_alarms/num_temp_beeps to 7/8
Tested with NCT6799D-R showing additional sysfs attributes:
* temp3-temp8: max/max_hyst/beep/alarm
* temp3-temp6: crit/offset
Signed-off-by: Ahmad Khalifa <ahmad@khalifa.ws>
Link: https://lore.kernel.org/r/20230802185820.3642399-1-ahmad@khalifa.ws
[groeck: Addressed cosmetic checkpatch complaints]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add base support for Renesas HS3001 temperature
and humidity sensors and its compatibles HS3002,
HS3003 and HS3004.
The sensor has a fix I2C address 0x44. The resolution
is fixed to 14bit (ref. Missing feature).
Missing feature:
- Accessing non-volatile memory: Custom board has no
possibility to control voltage supply of sensor. Thus,
we cannot send the necessary control commands within
the first 10ms after power-on.
Signed-off-by: Andre Werner <andre.werner@systec-electronic.com>
Link: https://lore.kernel.org/r/20230725042207.22310-2-andre.werner@systec-electronic.com
[groeck: Cosmetic documentation fixup; added documentation to index;
replaced probe_new with probe dropped unused variable]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The following warning is given by the Smatch static checker:
drivers/hwmon/hp-wmi-sensors.c:1937 hp_wmi_sensors_init()
error: uninitialized symbol 'pevents'.
If there are no instances of the HPBIOS_PlatformEvents WMI object
available, init_platform_events() never initializes this pointer,
which may then be passed to hp_wmi_debugfs_init() uninitialized.
The impact should be limited because hp_wmi_debugfs_init() uses this
pointer only if the count of HPBIOS_PlatformEvents instances is _not_
zero, while conversely, it will be uninitialized only if the count of
such instances _is_ zero. However, passing it uninitialized still
constitutes a bug.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-hwmon/f72c129b-8c57-406a-bf41-bd889b65ea0f@moroto.mountain/
Signed-off-by: James Seo <james@equiv.tech>
Link: https://lore.kernel.org/r/20230725094817.588640-1-james@equiv.tech
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 2a2b13ae50 ("platform/x86: wmi: Allow retrieving the number of
WMI object instances") means we no longer need to find this ourselves.
Signed-off-by: James Seo <james@equiv.tech>
Link: https://lore.kernel.org/r/20230722172513.9324-2-james@equiv.tech
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* Add additional VIN/IN_MIN/IN_MAX register values
* Separate ALARM/BEEP bits for nct6799
* Update scaling factors for nct6799
Registers/alarms match for NCT6796D-S and NCT6799D-R
Tested on NCT6799D-R for new IN/MIN/MAX and ALARMS
Signed-off-by: Ahmad Khalifa <ahmad@khalifa.ws>
Link: https://lore.kernel.org/r/20230719224142.411237-1-ahmad@khalifa.ws
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MP2973 & MP2971 return PGOOD instead of PB_STATUS_POWER_GOOD_N.
Fix that in the read_word_data hook.
MP2975 should not be affected, but that has not been confirmed with
hardware.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20230731092204.2933045-1-Naresh.Solanki@9elements.com
[groeck: Rephrased description to indicate that MP2975 is likely not affected]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for PMBUS_IOUT_OC_FAULT_LIMIT.
Add a helper function to convert the limit to LINEAR11 format
and read data->info.phases[0] on MP2971 and MP2973 as well.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20230714135124.2645339-8-Naresh.Solanki@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support to expose the PMBUS regulator.
Tested on MP2973 and MP2971.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20230714135124.2645339-7-Naresh.Solanki@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for MP2971 and MP2973, the successor of MP2975.
The major differences are:
- On MP2973 and MP2971 the Vref cannot be read and thus most of
the OVP/current calculations won't work.
- MP2973 and MP2971 also support LINEAR format for VOUT
- MP2973 and MP2971 do not support OVP2
- On MP2973 and MP2971 most registers are in LINEAR format
- The IMVP9_EN bit has a different position
- Per phase current sense haven't been implemented.
As on MP2975 most of the FAULT_LIMIT and WARN_LIMIT registers
have been redefined and doesn't provide the functionality as
defined in PMBUS spec.
Tested on MP2973 and MP2971.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20230714135124.2645339-6-Naresh.Solanki@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In order to add support for MP2973 and MP2971 replace hardcoded
phase count for both channels by a variable.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20230714135124.2645339-5-Naresh.Solanki@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In order to upstream MP2973/MP2971 simplify the code by removing support
for various VOUT formats. The MP2973 and MP2971 supports all PMBUS
supported formats for VOUT, while the MP2975 only support DIRECT and
VID for VOUT.
In DIRECT mode all chips report the voltage in 1mV/LSB.
Configure the chip to use DIRECT format for VOUT and drop the code
conversion code for other formats. The to be added chips MP2973/MP2971
will be configured to also report VOUT in DIRECT format.
The maximum voltage that can be reported in DIRECT format is 32768mV.
This is sufficient as the maximum output voltage for VR12/VR13 is
3040 mV.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20230714135124.2645339-4-Naresh.Solanki@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for differntiating between the chips.
The following commits will make use of this mechanism.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20230714135124.2645339-3-Naresh.Solanki@9elements.com
[groeck: double-cast of_device_get_match_data() to make gcc happy]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add test if thermistor sensor type attribute should be visible, i.e.
test if the attribute is defined.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20230707123005.956415-3-frank@crawford.emu.id.au
[groeck: Dropped unnecessary 'type' variable in it87_temp_is_visible()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The temperature sensor type will need to be used in multiple places, so
split it out into its own function.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20230707123005.956415-2-frank@crawford.emu.id.au
[groeck: Dropped unnecessary 'type' variable in show_temp_type()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Move detection logic to the start of init() function so we won't
instantiate the driver if the board is not compatible.
Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230717222526.229984-3-samsagax@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* Increase available bits, IN: 16 to 24, FAN: 8 to 12,
TEMP: 6 to 12
* Reorder alarm/beep definitions to match in order to allow
additional inputs in the future
* Remove comments about 'unused' bits as probe() is a better
reference
Testing note:
* Tested on nct6799 with IN/FAN/TEMP, and changing min/max/high/hyst,
that triggers the corresponding alarms correctly. Good confirmation
on the original mapping of the registers and masks.
As to be expected, only 4 fans and 2 temps (fixed) have limits
currently on nct6799 on my board.
* Trouble with testing intrusion alarms and beeps, no way to confirm
those. As I understand now, intrusion/caseopen is probably not
connected on my board.
And I haven't seen a buzzer on a board in ages.
Signed-off-by: Ahmad Khalifa <ahmad@khalifa.ws>
Link: https://lore.kernel.org/r/20230717201050.1657809-1-ahmad@khalifa.ws
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
SMM665 and related chips are power controller/sequencer chips from
Summit Microelectronics. The company was acquired by Qualcomm in 2012,
and support for the chip series stopped.
The chips are long since gone from active use, making the driver
unsupportable and just consuming space and compile time. Remove it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
nct6799d-r and nct6796d-s are very similar and chip_id is only
different in the version nibblet.
Since both will be detected by the driver anyway due to the
chipid mask, they should be labeled together for dmesg msg.
Signed-off-by: Ahmad Khalifa <ahmad@khalifa.ws>
Link: https://lore.kernel.org/r/20230715195244.1334723-1-ahmad@khalifa.ws
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch introduces support for handling more than 32 DIMMs by
utilizing bitmap operations. The changes ensure that the driver can
handle a higher number of DIMMs efficiently.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20230711152144.755177-1-Naresh.Solanki@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
strlcpy() reads the entire source buffer first.
This read may exceed the destination size limit.
This is both inefficient and can lead to linear read
overflows if a source string is not NUL-terminated [1].
In an effort to remove strlcpy() completely [2], replace
strlcpy() here with direct assignment.
strlcpy in this file is used to copy fixed-length strings which can be
completely avoided by direct assignment and is safe to do so. strlen()
is used to return the length of @tbuf.
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#strlcpy
[2] https://github.com/KSPP/linux/issues/89
Signed-off-by: Azeem Shaikh <azeemshaikh38@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230712214307.2424810-1-azeemshaikh38@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230714174607.4057185-1-robh@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Like the IBM CFFPS driver, export the PSU's firmware version to a
debugfs attribute as reported in the manufacturer register.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20230628153453.122213-1-eajames@linux.ibm.com
[groeck: Dropped unused variable; changed buffer from char to u8]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add thermal info support for AMD Family 1Ah-based models. Support is
provided on a per-socket granularity.
Co-developed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Avadhut Naik <Avadhut.Naik@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230809035244.2722455-3-avadhut.naik@amd.com
Add a 200ms delay after sending a ctrl report to Quadro,
Octo, D5 Next and Aquaero to give them enough time to
process the request and save the data to memory. Otherwise,
under heavier userspace loads where multiple sysfs entries
are usually set in quick succession, a new ctrl report could
be requested from the device while it's still processing the
previous one and fail with -EPIPE. The delay is only applied
if two ctrl report operations are near each other in time.
Reported by a user on Github [1] and tested by both of us.
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/issues/82
Fixes: 752b927951 ("hwmon: (aquacomputer_d5next) Add support for Aquacomputer Octo")
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20230807172004.456968-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend the functionality of hwmon (peci/dimmtemp) for Sapphire Rapids
platform.
Add the corresponding Sapphire Rapids ID and threshold code.
The patch has been tested on a 4S system with 64 DIMMs installed.
Verified read of DIMM temperature thresholds & temperature.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Iwona Winiarska <iwona.winiarska@intel.com>
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Link: https://lore.kernel.org/r/20230725104354.33920-3-Naresh.Solanki@9elements.com
Industrial processor i3255 supports temperatures -40 deg celcius
to 105 deg Celcius. The current implementation of k10temp_read_temp
rounds off any negative temperatures to '0'. To fix this,
the following changes have been made.
A flag 'disp_negative' is added to struct k10temp_data to support
AMD i3255 processors. Flag 'disp_negative' is set if 3255 processor
is found during k10temp_probe. Flag 'disp_negative' is used to
determine whether to round off negative temperatures to '0' in
k10temp_read_temp.
Signed-off-by: Baskaran Kannan <Baski.Kannan@amd.com>
Link: https://lore.kernel.org/r/20230727162159.1056136-1-Baski.Kannan@amd.com
Fixes: aef17ca127 ("hwmon: (k10temp) Only apply temperature offset if result is positive")
Cc: stable@vger.kernel.org
[groeck: Fixed multi-line comment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pass i2c_client to _pmbus_is_enabled to drop the assumption
that a regulator device is passed in.
This will fix the issue of a NULL pointer dereference when called from
_pmbus_get_flags.
Fixes: df5f6b6af0 ("hwmon: (pmbus/core) Generalise pmbus get status")
Cc: stable@vger.kernel.org # v6.4
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20230725125428.3966803-2-Naresh.Solanki@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Refactor pmbus_is_enabled() to return the status without any additional
processing as it is already done in _pmbus_is_enabled().
Fixes: df5f6b6af0 ("hwmon: (pmbus/core) Generalise pmbus get status")
Cc: stable@vger.kernel.org # v6.4
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20230725125428.3966803-1-Naresh.Solanki@9elements.com
[groeck: Rephrased commit message]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Scaling for VTT/VIN5/VIN6 registers were based on prior chips
* Split scaling factors for 6798/6799 and assign at probe()
* Pass them through driver data to sysfs functions
Tested on nct6799 with old/new input/min/max
Fixes: 0599682b82 ("hwmon: (nct6775) Add support for NCT6798D")
Signed-off-by: Ahmad Khalifa <ahmad@khalifa.ws>
Link: https://lore.kernel.org/r/20230719192848.337508-1-ahmad@khalifa.ws
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A driver should not be manually adding groups in its probe function (it
will race with userspace), so replace the call to devm_device_add_groups()
to use the platform dev_groups callback instead.
This will allow for removal of the devm_device_add_groups() function.
Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com>
Fixes: be144ee491 ("hwmon: (oxp-sensors) Add tt_toggle attribute on supported boards")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230717222526.229984-2-samsagax@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 662d20b3a5 ("hwmon: (aquacomputer_d5next) Add support for
temperature sensor offsets") changed aqc_get_ctrl_val() to return
the value through a parameter instead of through the return value,
but didn't fix up a case that relied on the old behavior. Fix it
to use the proper received value and not the return code.
Fixes: 662d20b3a5 ("hwmon: (aquacomputer_d5next) Add support for temperature sensor offsets")
Cc: stable@vger.kernel.org
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20230714120712.16721-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Here are a small set of changes for 6.5-rc1 for some driver core
changes. Included in here are:
- device property cleanups to make it easier to write "agnostic"
drivers when regards to the firmware layer underneath them (DT vs.
ACPI)
- debugfs documentation updates
- devres additions
- sysfs documentation and changes to handle empty directory creation
logic better
- tiny kernfs optimizations
- other tiny changes
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZKKSEQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymoowCfT+Joha+cz4edAFUvd55lKPPJJFsAoNiprHmX
di37sirvn6vo54Hk0Nyq
=qqTo
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here are a small set of changes for 6.5-rc1 for some driver core
changes. Included in here are:
- device property cleanups to make it easier to write "agnostic"
drivers when regards to the firmware layer underneath them (DT vs.
ACPI)
- debugfs documentation updates
- devres additions
- sysfs documentation and changes to handle empty directory creation
logic better
- tiny kernfs optimizations
- other tiny changes
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
sysfs: Skip empty folders creation
sysfs: Improve readability by following the kernel coding style
drivers: fwnode: fix fwnode_irq_get[_byname]()
ata: ahci_platform: Make code agnostic to OF/ACPI
device property: Implement device_is_compatible()
ACPI: Move ACPI_DEVICE_CLASS() to mod_devicetable.h
base/node: Use 'property' to identify an access parameter
driver core: device.h: add some missing kerneldocs
kernfs: fix missing kernfs_idr_lock to remove an ID from the IDR
isa: Remove unnecessary checks
MAINTAINERS: add entry for auxiliary bus
debugfs: Correct the 'debugfs_create_str' docs
serial: qcom_geni: Comment use of devm_krealloc rather than devm_krealloc_array
iio: adc: Use devm_krealloc_array
hwmon: pmbus: Use devm_krealloc_array
- Add support for TI TPS6594/TPS6593/LP8764 PMICs
- Add support for Samsung RT5033 Battery Charger
- Add support for Analog Devices MAX77540 and MAX77541 PMICs
- New Device Support
- Add support for SPI to Rockchip RK808 (and friends)
- Add support for AXP192 PMIC to X-Powers AXP20X
- Add support for AXP313a PMIC to X-Powers AXP20X
- Add support for RK806 to Rockchip RK8XX
- Removed Device Support
- Removed MFD support for Richtek RT5033 Battery
- Fix-ups
- Remove superfluous code
- Switch I2C drivers from .probe_new() to .probe()
- Convert over to managed resources (devm_*(), etc)
- Use dev_err_probe() for returning errors from .probe()
- Add lots of Device Tree bindings / support
- Improve cache efficiency by switching to Maple
- Use own exported namespaces (NS)
- Include missing and remove superfluous headers
- Start using / convert to the new shutdown sys-off API
- Trivial: variable / define renaming
- Make use of of_property_read_reg() when requesting DT 'reg's
- Bug Fixes
- Fix chip revision readout due to incorrect data masking
- Amend incorrect register and mask values used for charger state
- Hide unused functionality at compile time
- Fix resource leaks following error handling routines
- Return correct error values and fix error handling in general
- Repair incorrect device names - used for device matching
- Remedy broken module auto-loading
-----BEGIN PGP SIGNATURE-----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=EmOj
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for TI TPS6594/TPS6593/LP8764 PMICs
- Add support for Samsung RT5033 Battery Charger
- Add support for Analog Devices MAX77540 and MAX77541 PMICs
New Device Support:
- Add support for SPI to Rockchip RK808 (and friends)
- Add support for AXP192 PMIC to X-Powers AXP20X
- Add support for AXP313a PMIC to X-Powers AXP20X
- Add support for RK806 to Rockchip RK8XX
Removed Device Support:
- Removed MFD support for Richtek RT5033 Battery
Fix-ups:
- Remove superfluous code
- Switch I2C drivers from .probe_new() to .probe()
- Convert over to managed resources (devm_*(), etc)
- Use dev_err_probe() for returning errors from .probe()
- Add lots of Device Tree bindings / support
- Improve cache efficiency by switching to Maple
- Use own exported namespaces (NS)
- Include missing and remove superfluous headers
- Start using / convert to the new shutdown sys-off API
- Trivial: variable / define renaming
- Make use of of_property_read_reg() when requesting DT 'reg's
Bug Fixes:
- Fix chip revision readout due to incorrect data masking
- Amend incorrect register and mask values used for charger state
- Hide unused functionality at compile time
- Fix resource leaks following error handling routines
- Return correct error values and fix error handling in general
- Repair incorrect device names - used for device matching
- Remedy broken module auto-loading"
* tag 'mfd-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (51 commits)
dt-bindings: mfd: max77541: Add ADI MAX77541/MAX77540
iio: adc: max77541: Add ADI MAX77541 ADC Support
regulator: max77541: Add ADI MAX77541/MAX77540 Regulator Support
dt-bindings: regulator: max77541: Add ADI MAX77541/MAX77540 Regulator
mfd: Switch two more drivers back to use struct i2c_driver::probe
dt-bindings: mfd: samsung,s5m8767: Simplify excluding properties
mfd: stmpe: Only disable the regulators if they are enabled
mfd: max77541: Add ADI MAX77541/MAX77540 PMIC Support
dt-bindings: mfd: gateworks-gsc: Remove unnecessary fan-controller nodes
mfd: core: Use of_property_read_reg() to parse "reg"
mfd: stmfx: Nullify stmfx->vdd in case of error
mfd: stmfx: Fix error path in stmfx_chip_init
mfd: intel-lpss: Add missing check for platform_get_resource
mfd: stpmic1: Add PMIC poweroff via sys-off handler
mfd: stpmic1: Fixup main control register and bits naming
dt-bindings: mfd: qcom,tcsr: Add the compatible for IPQ8074
mfd: tps65219: Add support for soft shutdown via sys-off API
mfd: pm8008: Drop bogus i2c module alias
mfd: pm8008: Fix module autoloading
mfd: tps65219: Add GPIO cell instance
...
These are mostly minor cleanups and bugfixes that address harmless
problems.
The largest branch is a conversion of the omap platform
to use GPIO descriptors throughout the tree, for any devices that
are not fully converted to devicetree.
The Samsung Exynos platform gains back support for the Exynos4212
chip that was previously unused and removed but is now used for
the Samsung Galaxy Tab3.
-----BEGIN PGP SIGNATURE-----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=z6FU
-----END PGP SIGNATURE-----
Merge tag 'soc-arm-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"These are mostly minor cleanups and bugfixes that address harmless
problems.
The largest branch is a conversion of the omap platform to use GPIO
descriptors throughout the tree, for any devices that are not fully
converted to devicetree.
The Samsung Exynos platform gains back support for the Exynos4212 chip
that was previously unused and removed but is now used for the Samsung
Galaxy Tab3"
* tag 'soc-arm-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (24 commits)
ARM: omap2: Fix copy/paste bug
MAINTAINERS: Replace my email address
Input: ads7846 - fix pointer cast warning
Input: ads7846 - Fix usage of match data
ARM: omap2: Fix checkpatch issues
arm: omap1: replace printk() with pr_err macro
ARM: omap: Fix checkpatch issues
ARM: s3c: Switch i2c drivers back to use .probe()
ARM: versatile: mark mmc_status() static
ARM: spear: include "pl080.h" for pl080_get_signal() prototype
ARM: sa1100: address missing prototype warnings
ARM: pxa: fix missing-prototypes warnings
ARM: orion5x: fix d2net gpio initialization
ARM: omap2: fix missing tick_broadcast() prototype
ARM: omap1: add missing include
ARM: lpc32xx: add missing include
ARM: imx: add missing include
ARM: highbank: add missing include
ARM: ep93xx: fix missing-prototype warnings
ARM: davinci: fix davinci_cpufreq_init() declaration
...
struct i2c_driver::probe_new is about to go away. Switch the driver to
use the probe callback with the same prototype.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230626085145.554616-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This device is an iteration over the AOKZOE A1 with the same EC mapping
and features.
It also has support for tt_toggle.
Signed-off-by: Jerrod Frost <jcfrosty@proton.me>
Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com>
Link: https://lore.kernel.org/r/20230625012347.121352-2-samsagax@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The series 2022/2023 reports slightly longer vendor/product strings
and shares USB ids. Technically the reply size is the USB HID packet
size (64 bytes) but all the supported commands do not use more than 8
bytes and replies reporting back strings do not use more then 24 bytes
(vendor and product are in one string in the newer devices now). The
rest of the reply is always filled with '\0'. Also update comments
and documentation accordingly.
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/ZJbB72CAPmLflhHG@monster.localdomain
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix some typos, adjust documentation and comments to current state of
knowledge and update coding style to be more uniform.
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/ZJWf3H972hGgLK-8@monster.localdomain
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
According to ADI, changing PMON_CONFIG while the ADC is running can have
unexpected results. ADI recommends halting the ADC with PMON_CONTROL
before setting PMON_CONFIG and then resume after. Follow ADI
recommendation and disable ADC while PMON_CONFIG is updated.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230614163605.3688964-3-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
According to ADI, changing PMON_CONFIG while ADC is running can have
unexpected results. ADI recommends halting the ADC with PMON_CONTROL
before setting PMON_CONFIG and then resume after.
To prepare for this change, rename adm1275_read_pmon_config()
and adm1275_write_pmon_config() to adm1275_read_samples() and
adm1275_write_samples() to more accurately reflect the functionality
of the code. Introduce new function adm1275_write_pmon_config()
and use it for all code writing into the PMON_CONFIG register.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230614163605.3688964-2-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Take return logic on error out of if-else, eliminating
duplicated code in tt_togle_store() function.
Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com>
Link: https://lore.kernel.org/r/20230617181159.32844-3-samsagax@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT6799D is mostly compatible to NCT6798D, with minor variations.
Note that NCT6798D and NCT6799D have a new means to select temperature
sources, and to report temperatures from those sources. This is not
currently implemented, meaning that most likely not all temperatures
are reported.
Cc: Sebastian Arnhold <sebastian.arnhold@posteo.de>
Cc: Ahmad Khalifa <ahmad@khalifa.ws>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Arnhold <sebastian.arnhold@posteo.de>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Link: https://lore.kernel.org/r/20221228135744.281752-1-linux@roeck-us.net
OneXPlayer boards from the last generation (both for OneXPlayer and AOK
ZOE brands) have a toggle in the EC to switch the "Turbo/Silent" button
into a different keyboard event.
Add a means to use that "Turbo button takeover" function and expose it
to userspace in a custom sysfs `tt_toggle` attribute. It can be read to
take the current state. Write 1|0 to activate the function. The specific
keycode is dependent on the board but can be checked by running
`evtest` utility.
Newer BIOS on the OneXPlayer added this function aside from string changes.
Add a board enum to differentiate it from the old OneXplayer Mini AMD BIOS.
Currently known supported boards:
- AOK ZOE A1
- OneXPlayer Mini AMD (only newer BIOS version supported)
- OneXPlayer Mini Pro
Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com>
Link: https://lore.kernel.org/r/20230611143332.40590-2-samsagax@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for medium repeatability.
Per datasheet:
The stated repeatability is 3 times the standard deviation (3σ)
of multiple consecutive measurements at the stated repeatability
and at constant ambient conditions. It is a measure for the noise
on the physical sensor output. Different measurement modes allow
for high/medium/low repeatability.
For the humidity sensor, repeatability is documented as
0.25% RH for low repeatability, 0.15% RH for medium repeatability,
and 0.10% RH for high repeatability. Support all three modes.
Signed-off-by: JuenKit Yip <JuenKit_Yip@hotmail.com>
Link: https://lore.kernel.org/r/DB4PR10MB6261A70CD0444248ADDCC3219258A@DB4PR10MB6261.EURPRD10.PROD.OUTLOOK.COM
[groeck: Added details to description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Move m10bmc_sys_read() out from the header to prepare it for adding
more code into the function which would make it too large to be a
static inline any more.
While at it, replace the vague wording in function comment with more
precise statements.
Reviewed-by: Russ Weight <russell.h.weight@intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net> # For hwmon
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230417092653.16487-4-ilpo.jarvinen@linux.intel.com
New revisions of MAX16508 report MAX16508.xx or MAX16508y.xx as device ID,
but are functionally similar to MAX16508. Add support for those chip
variants.
Cc: Vlad Sytchenko <vsytch@google.com>
Cc: Steve Foreman <foremans@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The tmp464 is only capable of performing single register read and write
operations which means it gains no advantage from using a rbtree register
cache, convert it to using the more modern maple tree register cache
instead. This should be more efficient.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230609-hwmon-maple-v1-5-8edacce86b28@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The tmp108 is only capable of performing single register read and write
operations which means it gains no advantage from using a rbtree register
cache, convert it to using the more modern maple tree register cache
instead. This should be more efficient.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230609-hwmon-maple-v1-4-8edacce86b28@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The tmp102 is only capable of performing single register read and write
operations which means it gains no advantage from using a rbtree register
cache, convert it to using the more modern maple tree register cache
instead. This should be more efficient.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230609-hwmon-maple-v1-3-8edacce86b28@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The lm95245 is only capable of performing single register read and write
operations which means it gains no advantage from using a rbtree register
cache, convert it to using the more modern maple tree register cache
instead. This should be more efficient.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230609-hwmon-maple-v1-2-8edacce86b28@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The lm75 is only capable of performing single register read and write
operations which means it gains no advantage from using a rbtree register
cache, convert it to using the more modern maple tree register cache
instead. This should be more efficient.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230609-hwmon-maple-v1-1-8edacce86b28@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Support for FAN_CTL ON/OFF is currently disabled only for IT8603E but
there are severl chips that don't support the configuration bits to turn
off fan control entirely. Generalise this support for any chip.
Add feature flag FEAT_FANCTL_ONOFF for chips that support configuration
bits for management of fan control off and assign all chips that support
the configuration.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20230527094756.3464256-1-frank@crawford.emu.id.au
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch removes the error checking for debugfs_create_dir
in adm1266.c. This is because the debugfs_create_dir() does not
return NULL but an ERR_PTR after an error.
The DebugFS kernel API is developed in a way that the
caller can safely ignore the errors that occur during
the creation of DebugFS nodes.The debugfs Api handles
it gracefully. The check is unnecessary.
Link to the comment above debugfs_create_dir:
https://elixir.bootlin.com/linux/latest/source/fs/debugfs/inode.c#L565
Signed-off-by: Osama Muhammad <osmtendev@gmail.com>
Link: https://lore.kernel.org/r/20230526163938.9903-1-osmtendev@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch removes the error checking for debugfs_create_dir
in ucd9000.c. This is because the debugfs_create_dir() does not
return NULL but an ERR_PTR after an error.
The DebugFS kernel API is developed in a way that the
caller can safely ignore the errors that occur during
the creation of DebugFS nodes.The debugfs Api handles
it gracefully. The check is unnecessary.
Link to the comment above debugfs_create_dir:
https://elixir.bootlin.com/linux/latest/source/fs/debugfs/inode.c#L565
Signed-off-by: Osama Muhammad <osmtendev@gmail.com>
Link: https://lore.kernel.org/r/20230526154906.6370-1-osmtendev@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Checking for Kconfig symbols with #if is wrong:
drivers/hwmon/hp-wmi-sensors.c:1141:5: error: "CONFIG_DEBUG_FS" is not defined, evaluates to 0 [-Werror=undef]
This could be an #ifdef, but an IS_ENABLED() check is even better to
give the best compile coverage.
Fixes: 23902f98f8 ("hwmon: add HP WMI Sensors driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: James Seo <james@equiv.tech>
Link: https://lore.kernel.org/r/20230601213216.3220550-1-arnd@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Hewlett-Packard (and some HP Compaq) business-class computers report
hardware monitoring information via WMI. This driver exposes that
information to hwmon.
Initial support is provided for temperature, fan speed, and intrusion
sensor types. Provisional support is provided for voltage and current
sensor types.
HP's WMI implementation permits many other types of numeric sensors.
Therefore, a debugfs interface is also provided to enumerate and
inspect all numeric sensors visible on the WMI side. This should
facilitate adding support for other sensor types in the future.
Tested on a HP Z420, a HP EliteOne 800 G1, and a HP Compaq Elite 8300
SFF.
Note that provisionally supported sensor types are untested and seem
to be rare-to-nonexistent in the wild, having been encountered
neither on test systems nor in ACPI dumps from the Linux Hardware
Database. They are included because their popularity in general makes
their presence on past or future HP systems plausible and because no
doubt exists as to how the sensors themselves would be represented in
WMI (alarm attributes will need to wait for hardware to be located).
A 2005 HP whitepaper gives the relevant sensor object MOF definition
and sensor value scaling calculation, and both this driver and the
official HP Performance Advisor utility comply with them (confirmed
in the latter case by reverse engineering).
Link: https://h20331.www2.hp.com/hpsub/downloads/cmi_whitepaper.pdf
Signed-off-by: James Seo <james@equiv.tech>
Link: https://lore.kernel.org/r/20230522115645.509701-1-james@equiv.tech
[groeck: Set error return value for intrusion writes to -EINVAL.
Always accept writes of 0 even if there was no intrusion. ]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We don't need to pass device structure to write_to_ec() so we remove
that from the function declaration.
The same is valid for pwm_enable() and pwm_disable() as we were passing
the pointer to hand it off to write_to_ec().
Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com>
Link: https://lore.kernel.org/r/20230525142652.41981-1-samsagax@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX31827 is a low-power temperature switch with I2C interface.
The device is a ±1°C accuracy from -40°C to +125°C
(12 bits) local temperature switch and sensor with I2C/SM-
Bus interface. The combination of small 6-bump wafer-lev-
el package (WLP) and high accuracy makes this temper-
ature sensor/switch ideal for a wide range of applications.
Signed-off-by: Daniel Matyas <daniel.matyas@analog.com>
Link: https://lore.kernel.org/r/20230524160131.14081-2-daniel.matyas@analog.com
[groeck: Improved define alignment, return -EINVAL after bad user input,
fixed up compatible statement]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for compatible AHT20 temperature/humidity sensor. The only
difference between the two is that AHT20 has additional crc8 byte.
It seems like AHT15 is also supported by the driver but it wasn't
verified and tested yet.
Tested on Beaglebone black rev C.
Signed-off-by: Kirill Yatsenko <kiriyatsenko@gmail.com>
Link: https://lore.kernel.org/r/20230524201912.815993-1-kiriyatsenko@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A newer BIOS version for the OneXPlayer Mini AMD modified vendor and
board name strings. Add those to the match table and set the same board
model as older OXP Mini AMD.
Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com>
Link: https://lore.kernel.org/r/20230517183540.187383-1-samsagax@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose various hardware sensors of the
Aquacomputer Leakshield leak prevention system, which communicates
through a proprietary USB HID protocol. Implemented by Noah Bergbauer [1].
Two temperature sensors are exposed, along with pressure (current, min, max
and target), reservoir volume (total and filled), pump speed and flow. Pump
speed and flow values are user provided and allow the Leakshield to
optimize its operation. Writing them to the device is subject of future
patches.
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/41
Originally-from: Noah Bergbauer <main@ehvag.de>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20230520095447.509287-3-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Exit from the function immediately if the poll time hasn't yet expired.
Therefore the code after the check can be moved one tab to the left which
improves readability.
Signed-off-by: Kirill Yatsenko <kiriyatsenko@gmail.com>
Link: https://lore.kernel.org/r/20230511202633.299174-2-kiriyatsenko@gmail.com
[groeck: Dropped else after return]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix typos in the description of the return value section of the
functions. The word 'succesfull' is incorrect, it should be 'successful'.
Signed-off-by: Kirill Yatsenko <kiriyatsenko@gmail.com>
Link: https://lore.kernel.org/r/20230511202633.299174-1-kiriyatsenko@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 848ba0a2f2 ("hwmon: (core) Rename groups parameter in API to
extra_groups") renames the 'groups' parameter of
devm_hwmon_device_register_with_info() to 'extra_groups' in
hwmon-kernel-api.txt (later .rst) and hwmon.h, but this change was not
propagated to the function code itself in hwmon.c. Finish the job.
Note that hwmon_device_register_with_info() has the same
parameter, and the name of that parameter was changed in all
three files. Harmonizing the name between these related
functions also removes a potential source of confusion.
Signed-off-by: James Seo <james@equiv.tech>
Link: https://lore.kernel.org/r/20230507151051.1861929-1-james@equiv.tech
[groeck: Fixed up SHA reference in description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
beep_enable, inX_beep, currX_beep, fanX_beep, and tempX_beep
are standard attributes mentioned in the sysfs interface
specification but not implemented in the hwmon core. Since
these are not deprecated, implement them.
Adding beep_mask is not necessary, as it is deprecated and
the drivers already using it are manually defining it.
Signed-off-by: James Seo <james@equiv.tech>
Link: https://lore.kernel.org/r/20230507152216.1862653-1-james@equiv.tech
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230505131718.1210071-1-u.kleine-koenig@pengutronix.de
[groeck: Added missing change in pmbus/acbel-fsg032.c]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some chips are known to only have 4 temperature sensors and there is no
requirement to test for more. Currently only the IT8622E fits this
category.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20230430045032.1723288-1-frank@crawford.emu.id.au
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Instead of of_property_read_*() use the equivalent
device_property_read_*() API. This will allow these properties to be
used on DT unaware platforms. For DT aware platforms this will be a
noop.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20230418233656.869055-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add feature and support for chips with only 4 fans.
Reorder macro definitions to bring all fan definitions together.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20230429115205.1547251-2-frank@crawford.emu.id.au
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Only the temp sensors that I can verify are present. HWINFO in
Windows shows other accumulated data and statistics (time since
installed, total power used, etc) that I have not attempted to find.
Signed-off-by: Michael Carns <mike@carns.com>
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20230426200345.65765-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for handhelds with same EC registers
- AYANEO 2
- AYANEO GEEK
All functionality tests succeed on AYANEO 2 by "pastaq" user on Discord
and AYANEO GEEK tested by "oneoc" Discord user.
Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com>
Link: https://lore.kernel.org/r/20230426184420.99945-1-samsagax@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The PMON_CONFIG register on ADM1272 is a 16 bit register. Writing a 8 bit
value into it clears the upper 8 bits of the register, resulting in
unexpected side effects. Fix by writing the 16 bit register value.
Also, it has been reported that temperature readings are sometimes widely
inaccurate, to the point where readings may result in device shutdown due
to errant overtemperature faults. Improve by enabling temperature sampling.
While at it, move the common code for ADM1272 and ADM1278 into a separate
function, and clarify in the error message that an attempt was made to
enable both VOUT and temperature monitoring.
Last but not least, return the error code reported by the underlying I2C
controller and not -ENODEV if updating the PMON_CONFIG register fails.
After all, this does not indicate that the chip is not present, but an
error in the communication with the chip.
Fixes: 4ff0ce227a ("hwmon: (pmbus/adm1275) Add support for ADM1272")
Fixes: 9da9c2dc57 ("hwmon: (adm1275) enable adm1272 temperature reporting")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230602213447.3557346-1-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The GSC fan pwm temperature register is in centidegrees celcius but the
Linux hwmon convention is to use milidegrees celcius. Fix the scaling.
Fixes: 3bce5377ef ("hwmon: Add Gateworks System Controller support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://lore.kernel.org/r/20230606153004.1448086-1-tharvey@gateworks.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Now that it exists, use it instead of doing the multiplication manually.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: James Clark <james.clark@arm.com>
Link: https://lore.kernel.org/r/20230509094942.396150-3-james.clark@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PXA platform has a number of configurations that end up with
a warning like these when building with W=1:
drivers/hwmon/max1111.c:83:5: error: no previous prototype for 'max1111_read_channel' [-Werror=missing-prototypes]
arch/arm/mach-pxa/reset.c:86:6: error: no previous prototype for 'pxa_restart' [-Werror=missing-prototypes]
arch/arm/mach-pxa/mfp-pxa2xx.c:254:5: error: no previous prototype for 'keypad_set_wake' [-Werror=missing-prototypes]
drivers/clk/pxa/clk-pxa25x.c:70:14: error: no previous prototype for 'pxa25x_get_clk_frequency_khz' [-Werror=missing-prototypes]
drivers/clk/pxa/clk-pxa25x.c:325:12: error: no previous prototype for 'pxa25x_clocks_init' [-Werror=missing-prototypes]
drivers/clk/pxa/clk-pxa27x.c:74:14: error: no previous prototype for 'pxa27x_get_clk_frequency_khz' [-Werror=missing-prototypes]
drivers/clk/pxa/clk-pxa27x.c:102:6: error: no previous prototype for 'pxa27x_is_ppll_disabled' [-Werror=missing-prototypes]
drivers/clk/pxa/clk-pxa27x.c:470:12: error: no previous prototype for 'pxa27x_clocks_init' [-Werror=missing-prototypes]
arch/arm/mach-pxa/pxa27x.c:44:6: error: no previous prototype for 'pxa27x_clear_otgph' [-Werror=missing-prototypes]
arch/arm/mach-pxa/pxa27x.c:58:6: error: no previous prototype for 'pxa27x_configure_ac97reset' [-Werror=missing-prototypes]
arch/arm/mach-pxa/spitz_pm.c:170:15: error: no previous prototype for 'spitzpm_read_devdata' [-Werror=missing-prototypes]
The problem is that there is a declaration for each of these, but
it's only seen by the caller and not the callee. Moving these
into appropriate header files ensures that both use the same
calling conventions and it avoids the warnings.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20230516153109.514251-11-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In the unlikely event that something goes wrong with the device and
its registers, the fan_from_reg() function may return 0. This value
will cause a division-by-zero error in the show_pwm() function.
To prevent this, test the value of
fan_from_reg(data->fan_full_speed[nr]) against 0 before performing
the division. If the division-by-zero error is avoided, assign 0 to
the val variable.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: df9ec2dae0 ("hwmon: (f71882fg) Reorder symbols to get rid of a few forward declarations")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20230510143537.145060-1-n.zhandarovich@fintech.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening in
the driver core in the quest to be able to move "struct bus" and "struct
class" into read-only memory, a task now complete with these changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules for
all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most of
them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp7Sw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykitQCfamUHpxGcKOAGuLXMotXNakTEsxgAoIquENm5
LEGadNS38k5fs+73UaxV
=7K4B
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening
in the driver core in the quest to be able to move "struct bus" and
"struct class" into read-only memory, a task now complete with these
changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules
for all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most
of them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (120 commits)
device property: make device_property functions take const device *
driver core: update comments in device_rename()
driver core: Don't require dynamic_debug for initcall_debug probe timing
firmware_loader: rework crypto dependencies
firmware_loader: Strip off \n from customized path
zram: fix up permission for the hot_add sysfs file
cacheinfo: Add use_arch[|_cache]_info field/function
arch_topology: Remove early cacheinfo error message if -ENOENT
cacheinfo: Check cache properties are present in DT
cacheinfo: Check sib_leaf in cache_leaves_are_shared()
cacheinfo: Allow early level detection when DT/ACPI info is missing/broken
cacheinfo: Add arm64 early level initializer implementation
cacheinfo: Add arch specific early level initializer
tty: make tty_class a static const structure
driver core: class: remove struct class_interface * from callbacks
driver core: class: mark the struct class in struct class_interface constant
driver core: class: make class_register() take a const *
driver core: class: mark class_release() as taking a const *
driver core: remove incorrect comment for device_create*
MIPS: vpe-cmp: remove module owner pointer from struct class usage.
...
- Add a thermal zone 'devdata' accessor and modify several drivers to
use it (Daniel Lezcano).
- Prevent drivers from using the 'device' internal thermal zone
structure field directly (Daniel Lezcano).
- Clean up the hwmon thermal driver (Daniel Lezcano).
- Add thermal zone id accessor and thermal zone type accessor
and prevent drivers from using thermal zone fields directly (Daniel
Lezcano).
- Clean up the acerhdf and tegra thermal drivers (Daniel Lezcano).
- Add lower bound check for sysfs input to the x86_pkg_temp_thermal
Intel thermal driver (Zhang Rui).
- Add more thermal zone device encapsulation: prevent setting structure
field directly, access the sensor device instead the thermal zone's
device for trace, relocate the traces in drivers/thermal (Daniel
Lezcano).
- Use the generic trip point for the i.MX and remove the get_trip_temp
ops (Daniel Lezcano).
- Use the devm_platform_ioremap_resource() in the Hisilicon driver
(Yang Li).
- Remove R-Car H3 ES1.* handling as public has only access to the ES2
version and the upstream support for the ES1 has been shutdown (Wolfram
Sang).
- Add a delay after initializing the bank in order to let the time to
the hardware to initialze itself before reading the temperature
(Amjad Ouled-Ameur).
- Add MT8365 support (Amjad Ouled-Ameur).
- Preparational cleanup and DT bindings for RK3588 support (Sebastian
Reichel).
- Add driver support for RK3588 (Finley Xiao).
- Use devm_reset_control_array_get_exclusive() for the Rockchip driver
(Ye Xingchen).
- Detect power gated thermal zones and return -EAGAIN when reading the
temperature (Mikko Perttunen).
- Remove thermal_bind_params structure as it is unused (Zhang Rui)
- Drop unneeded quotes in DT bindings allowing to run yamllint (Rob
Herring).
- Update the power allocator documentation according to the thermal
trace relocation (Lukas Bulwahn).
- Fix sensor 1 interrupt status bitmask for the Mediatek LVTS sensor
(Chen-Yu Tsai).
- Use the dev_err_probe() helper in the Amlogic driver (Ye Xingchen).
- Add AP domain support to LVTS thermal controllers for mt8195
(Balsam CHIHI).
- Remove buggy call to thermal_of_zone_unregister() (Daniel Lezcano).
- Make thermal_of_zone_[un]register() private to the thermal OF code
(Daniel Lezcano).
- Create a private copy of the thermal zone device parameters
structure when registering a thermal zone (Daniel Lezcano).
- Fix a kernel NULL pointer dereference in thermal_hwmon (Zhang Rui).
- Revert recent message adjustment in thermal_hwmon (Rafael Wysocki).
- Use of_property_present() for testing DT property presence in
thermal control code (Rob Herring).
- Clean up thermal_list_lock locking in the thermal core (Rafael
Wysocki).
- Add DLVR support for RFIM control in the int340x Intel thermal
driver (Srinivas Pandruvada).
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAmRGvsYSHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRxekAQAJ/hhUZyY2hcFveNfrutkO8OGY+/rtz8
ozMxyfwAdHoD6/zg9zZQTHSQy3W9rx2FC3tYtwHlJopDYFQuNPsfrhYE97EfO9uT
Baou3OhoXV+ZJ0EZqIuTNuLaDPD/Hg8KSNmZvb6p/30bLR3Y/gKZutX9+S0x8qpG
y7JcA8qPDYTvNfxkDjYv3M7HlfpwIwpi/xPFuw9nI2Fdw0SYRWpHAQlNj6oaF0xT
EaNIg5zh4rR81T34/DpaOm1mfrg3Lg9xOJMU0laS5sKkn5Ea8s0E5s3vb5Quup61
eXL3DhxmsIv51+1URZMZIQo2FmogvLmgnIPQyaeSvtlic0t39YS70tL2i8JY6kfL
Tkhm8bS8jKQ6Y8GUvUbE/qadWFgkV4/lFTREVkKuq0XUU/YEpl5iQJAc0iEa0soy
SISucs/ugoFjqdlN1pNDv7mLIzqyYIF6tZekLZTVa1U++MHKRakY9folD3brc6xO
ewp1yO6e/fYZJx0K8LNlBRzXqNuV1Tl+kBDvUNHDNAEN8jONiZ2v+pDQ+VqYYxIc
1A2KVw0l3m0MQ97w3E8LqYJTH6f8bxSLxjXnHLSN0eAXJkn10olfz/RYNsqi+dUb
YBnFU8t3plGMVGrDcoDtO6hkujUw3oF7pibWeXXFEvIyRUcOA2e94kd57i9a1zLS
5yyH9UchFcQq
=XNJE
-----END PGP SIGNATURE-----
Merge tag 'thermal-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"These mostly continue to prepare the thermal control subsystem for
using unified representation of trip points, which includes cleanups,
code refactoring and similar and update several drivers (for other
reasons), which includes new hardware support.
Specifics:
- Add a thermal zone 'devdata' accessor and modify several drivers to
use it (Daniel Lezcano)
- Prevent drivers from using the 'device' internal thermal zone
structure field directly (Daniel Lezcano)
- Clean up the hwmon thermal driver (Daniel Lezcano)
- Add thermal zone id accessor and thermal zone type accessor and
prevent drivers from using thermal zone fields directly (Daniel
Lezcano)
- Clean up the acerhdf and tegra thermal drivers (Daniel Lezcano)
- Add lower bound check for sysfs input to the x86_pkg_temp_thermal
Intel thermal driver (Zhang Rui)
- Add more thermal zone device encapsulation: prevent setting
structure field directly, access the sensor device instead the
thermal zone's device for trace, relocate the traces in
drivers/thermal (Daniel Lezcano)
- Use the generic trip point for the i.MX and remove the
get_trip_temp ops (Daniel Lezcano)
- Use the devm_platform_ioremap_resource() in the Hisilicon driver
(Yang Li)
- Remove R-Car H3 ES1.* handling as public has only access to the ES2
version and the upstream support for the ES1 has been shutdown
(Wolfram Sang)
- Add a delay after initializing the bank in order to let the time to
the hardware to initialze itself before reading the temperature
(Amjad Ouled-Ameur)
- Add MT8365 support (Amjad Ouled-Ameur)
- Preparational cleanup and DT bindings for RK3588 support (Sebastian
Reichel)
- Add driver support for RK3588 (Finley Xiao)
- Use devm_reset_control_array_get_exclusive() for the Rockchip
driver (Ye Xingchen)
- Detect power gated thermal zones and return -EAGAIN when reading
the temperature (Mikko Perttunen)
- Remove thermal_bind_params structure as it is unused (Zhang Rui)
- Drop unneeded quotes in DT bindings allowing to run yamllint (Rob
Herring)
- Update the power allocator documentation according to the thermal
trace relocation (Lukas Bulwahn)
- Fix sensor 1 interrupt status bitmask for the Mediatek LVTS sensor
(Chen-Yu Tsai)
- Use the dev_err_probe() helper in the Amlogic driver (Ye Xingchen)
- Add AP domain support to LVTS thermal controllers for mt8195
(Balsam CHIHI)
- Remove buggy call to thermal_of_zone_unregister() (Daniel Lezcano)
- Make thermal_of_zone_[un]register() private to the thermal OF code
(Daniel Lezcano)
- Create a private copy of the thermal zone device parameters
structure when registering a thermal zone (Daniel Lezcano)
- Fix a kernel NULL pointer dereference in thermal_hwmon (Zhang Rui)
- Revert recent message adjustment in thermal_hwmon (Rafael Wysocki)
- Use of_property_present() for testing DT property presence in
thermal control code (Rob Herring)
- Clean up thermal_list_lock locking in the thermal core (Rafael
Wysocki)
- Add DLVR support for RFIM control in the int340x Intel thermal
driver (Srinivas Pandruvada)"
* tag 'thermal-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (55 commits)
thermal: intel: int340x: Add DLVR support for RFIM control
thermal/core: Alloc-copy-free the thermal zone parameters structure
thermal/of: Unexport unused OF functions
thermal/drivers/bcm2835: Remove buggy call to thermal_of_zone_unregister
thermal/drivers/mediatek/lvts_thermal: Add AP domain for mt8195
dt-bindings: thermal: mediatek: Add AP domain to LVTS thermal controllers for mt8195
thermal: amlogic: Use dev_err_probe()
thermal/drivers/mediatek/lvts_thermal: Fix sensor 1 interrupt status bitmask
MAINTAINERS: adjust entry in THERMAL/POWER_ALLOCATOR after header movement
dt-bindings: thermal: Drop unneeded quotes
thermal/core: Remove thermal_bind_params structure
thermal/drivers/tegra-bpmp: Handle offline zones
thermal/drivers/rockchip: use devm_reset_control_array_get_exclusive()
dt-bindings: rockchip-thermal: Support the RK3588 SoC compatible
thermal/drivers/rockchip: Support RK3588 SoC in the thermal driver
thermal/drivers/rockchip: Support dynamic sized sensor array
thermal/drivers/rockchip: Simplify channel id logic
thermal/drivers/rockchip: Use dev_err_probe
thermal/drivers/rockchip: Simplify clock logic
thermal/drivers/rockchip: Simplify getting match data
...
The bit flags in pmbus_driver_info functionality for YM-2151E chip were
joined with a comma operator instead of a bitwise OR. This means that
the last constant PMBUS_HAVE_IIN was not OR-ed with the other
PM_BUS_HAVE_* constants for this page but it initialized the next element
of the func array (which was not accessed from anywhere because of the
number of pages).
However, there is no need for setting PMBUS_HAVE_IIN in the 5Vsb page
because this command does not seem to be paged. Obviously, the device
only has one IIN sensor, so it doesn't make sense to query it again from
the second page.
Fixes: 1734b4135a ("hwmon: Add driver for fsp-3y PSUs and PDUs")
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Tomáš Pecka <tomas.pecka@cesnet.cz>
Link: https://lore.kernel.org/r/20230420171939.212040-1-tomas.pecka@cesnet.cz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose various hardware sensors of the
Aquacomputer Aquastream XT watercooling pump, which communicates
through a proprietary USB HID protocol. Implemented by Leonard Anderweit
[1] [2].
Coolant temp, fan IC and external temp sensor readings are available, along
with speed and voltage of both the pump and optionally connected fan.
It also exposes pump current.
Additionally, serial number and firmware version are exposed through
debugfs.
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/46
[2] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/49
Originally-from: Leonard Anderweit <leonard.anderweit@gmail.com>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20230416181702.9892-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Configure the IT8622E chip to disable/re-enable access via an SMBus when
reading or writing the chip's registers.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Disable/re-enable access through SMBus for chip registers when they are
are being read or written.
For simple cases this is done at the same time as when a mutex is set,
however, within loops or during initialisation it is done separately.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
[groeck: Fixed multi-line alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Handle errors from it87_update_device(), which currently only occurs if
SMBus access locking fails.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
[groeck: Fixed handling in show_temp_type()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add functions to disable and re-enable access by the SMBus for specific
chips.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Switch the driver to use the default debugfs attributes instead of
ones that provide the same data under different names. Use the lock
functions for the debugfs and led attributes, and simplify the input
history operation by dropping the timer and lock.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20230412161526.252294-3-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Debugfs operations may set the page number, which must be done
atomically with the subsequent i2c operation. Lock the update_lock
in the debugfs functions and provide a function for pmbus drivers
to lock and unlock the update_lock.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20230412161526.252294-2-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
0-day rightfully complains:
drivers/hwmon/pmbus/pmbus_core.c:3164:7-32: WARNING:
Threaded IRQ with no primary handler requested without IRQF_ONESHOT
(unless it is nested IRQ)
Without IRQF_ONESHOT, the primary interrupt may end up in a loop,
and the threaded interrupt handler may never execute. Request interrupt
with IRQF_ONESHOT and assume that the interrupt will cleared and re-enabled
by clearing the fault condition in the threaded interrupt handler.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/linux-hwmon/6436efbb.08+e+yEDqvRxvHDP%25lkp@intel.com/T/#u
Cc: Patrick Rudolph <patrick.rudolph@9elements.com>
Cc: Naresh Solanki <Naresh.Solanki@9elements.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TI ina2xx sensors according to datasheets have dedicated
vs supplies. Add it for proper work.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Link: https://lore.kernel.org/r/20230407160508.20479-3-clamor95@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add regulator events corresponding to regulator error in regulator flag
map.
Also capture the same in pmbus_regulator_get_flags.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20230328150335.90238-2-Naresh.Solanki@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add driver for the StarFive JH71x0 temperature sensor. You
can enable/disable it and read temperature in milli Celcius
through sysfs.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Co-developed-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Link: https://lore.kernel.org/r/20230321022644.107027-3-hal.feng@starfivetech.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The refinement of tjmax value retrieved from MSR_IA32_TEMPERATURE_TARGET
has been changed for several times.
Now, the raw value from MSR is used without refinement. Thus remove the
obsolete comment.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20230330103346.6044-2-rui.zhang@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After commit c0c67f8761 ("hwmon: (coretemp) Add support for dynamic
tjmax"), tjmax value is retrieved from MSR every time the temperature is
read.
This means that, with debug message enabled, the tjmax debug message is
printed out for every single temperature read for any CPU. This spams
the syslog.
Ideally, as tjmax is package scope unique, the debug message should show
once when tjmax is changed for one package. But this requires inventing
some new per-package data in the coretemp driver, and this is overkill.
To keep the code simple, delete the tjmax debug message.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20230330103346.6044-1-rui.zhang@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
clang with W=1 reports
drivers/hwmon/vt1211.c:198:20: error: unused function
'superio_outb' [-Werror,-Wunused-function]
static inline void superio_outb(int sio_cip, int reg, int val)
^
This function is not used so remove it.
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Juerg Haefliger <juergh@proton.me>
Link: https://lore.kernel.org/r/20230323211535.2637939-1-trix@redhat.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
PWM fans are controlled solely by the duty cycle of the PWM signal, they
do not care about the exact timing. Thus set usage_power to true to
allow less flexible hardware to work as a PWM source for fan control.
Signed-off-by: Lorenz Brun <lorenz@brun.one>
Link: https://lore.kernel.org/r/20230309011009.2109696-1-lorenz@brun.one
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Boards such as
* EX-B660M-V5 D4,
* PRIME A520M-A,
* PRIME A520M-A II,
* PRIME A520M-E,
* PRIME A520M-K,
* PRIME B360M-A,
* PRIME B360M-C,
* PRIME B460M-A R2.0,
* PRIME B550M-A AC,
* PRIME B550M-A WIFI II,
* PRIME B550M-K,
* PRIME B650M-A AX II,
* PRIME Z590-P WIFI,
* PRIME Z590-V,
* Pro A520M-C,
* ProArt B650-CREATOR,
* ProArt Z790-CREATOR WIFI,
* Pro B660M-C,
* Pro WS W680-ACE,
* Pro WS W680-ACE IPMI,
* ROG MAXIMUS XIII APEX,
* ROG MAXIMUS XIII EXTREME,
* ROG MAXIMUS XIII HERO,
* ROG MAXIMUS Z690 APEX,
* ROG MAXIMUS Z790 EXTREME,
* ROG STRIX B660-A GAMING WIFI,
* ROG STRIX Z590-A GAMING WIFI,
* ROG STRIX Z590-E GAMING WIFI,
* ROG STRIX Z590-F GAMING WIFI,
* ROG STRIX Z590-I GAMING WIFI,
* TUF GAMING A520M-PLUS,
* TUF GAMING A520M-PLUS II,
* TUF GAMING A520M-PLUS WIFI,
* TUF GAMING B660M-E D4,
* TUF GAMING B660-PLUS WIFI D4,
* TUF GAMING X570-PLUS_BR,
* TUF GAMING Z590-PLUS,
* Z490-GUNDAM (WI-FI),
* Z590 WIFI GUNDAM EDITION
have got a nct6775 chip, but by default there's no use of it
because of resource conflict with WMI method.
This commit adds such boards to the WMI monitoring list.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=204807
Signed-off-by: Denis Pauk <pauk.denis@gmail.com>
Tested-by: Nick Owens <mischief@offblast.org>
Tested-by: A. M. <de99like@mennucci.debian.net>
Link: https://lore.kernel.org/r/20230315225128.1236-1-pauk.denis@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add function pmbus get status that can be used to get both pmbus
specific status & regulator status
Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
...
Change in V4
- None
Changes in V3:
- Add pmbus_is_enabled function
Changes in V2:
- Add __maybe attribute for pmbus_get_status function
- Remove unrelated changes
Link: https://lore.kernel.org/r/20230301164434.1928237-2-Naresh.Solanki@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The PMBus status flag map(pmbus_regulator_status_flag_map) is moved
outside of the regulator #if block and the associated variable/struct
name updated to reflect as generic PMBus status.
This will make the PMBus status flag map more versatile and easier to
incorporate into different contexts and functions.
Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230301164434.1928237-1-Naresh.Solanki@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the option to control fan PWM on Aquacomputer Aquaero. The Aquaero is
the most complex Aquacomputer device, control is therefore more complicated
then on already supported devices.
Setting PWM requires multiple steps. First, an internal static PWM
controller is set to the desired PWM value. Second, the fan is set to use
that PWM controller. Last, the minimum and maximum accepted PWM values
of the fan are set to allow all possible PWM values.
Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
Link: https://lore.kernel.org/r/20230214220221.15003-7-leonard.anderweit@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add information on the Aquacomputer Aquaero control report and disable the
control report checksum for Aquaero. The Aquaero does not use the checksum
so it must be disabled to avoid overwriting the last two bytes of the
control report.
Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
Link: https://lore.kernel.org/r/20230214220221.15003-5-leonard.anderweit@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add device dependent control report id, secondary control report id,
secondary control report size and secondary control report for devices
which need different control report settings. All currently supported
devices use the same values.
Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
Link: https://lore.kernel.org/r/20230214220221.15003-4-leonard.anderweit@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add new function aqc_set_ctrl_vals() to support changing multiple control
values at once while sending only one control report.
Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
Link: https://lore.kernel.org/r/20230214220221.15003-3-leonard.anderweit@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for one byte control values. This extends aqc_set_ctrl_val()
and aqc_get_ctrl_val() with a type. Currently supported types are AQC_8
(one byte) and AQC_BE16 (two bytes big endian). More types will be added
in the future.
Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
Link: https://lore.kernel.org/r/20230214220221.15003-2-leonard.anderweit@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230310144706.1542434-1-robh@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230310144707.1542525-1-robh@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The 64-bit result will be cut to 32-bit automatically (by compiler)
due to the type of the destination value. No need to have an explicit
casting and especially additional conjunction which does the same.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230217191600.24837-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This seems to be a new revision of the device. RGB controls have changed,
but this driver doesn't touch them anyway.
Fan speed control reported to be working with existing userspace (hidraw)
software, so I assume it's compatible. Fan channel count is the same.
Recently added (0x1e71, 0x2019) seems to be the same device.
Discovered in liquidctl project:
https://github.com/liquidctl/liquidctl/issues/541
Signed-off-by: Aleksandr Mezin <mezin.alexander@gmail.com>
Link: https://lore.kernel.org/r/20230219105924.333007-1-mezin.alexander@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here). This
also fixes !CONFIG_OF error:
drivers/hwmon/gpio-fan.c:484:34: error: ‘of_gpio_fan_match’ defined but not used [-Werror=unused-const-variable=]
Note(groeck): The build error is only seen if Kconfig dependencies
are messed up. The driver depends on OF_GPIO which should depend
on OF. This was temporarily broken in linux-next, and it was
possible to select CONFIG_OF=n and CONFIG_SENSORS_GPIO_FAN=y.
Nevertheless, this is a sensible fix.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230312193723.478032-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
HWmon core receives an array of pointers to hwmon_channel_info and it
does not modify it, thus it can be array of const pointers for safety.
This allows drivers to make them also const.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The add_dev and remove_dev callbacks in struct class_interface currently
pass in a pointer back to the class_interface structure that is calling
them, but none of the callback implementations actually use this pointer
as it is pointless (the structure is known, the driver passed it in in
the first place if it is really needed again.)
So clean this up and just remove the pointer from the callbacks and fix
up all callback functions.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Allen Hubbe <allenbh@gmail.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Alexandre Bounine <alex.bou9@gmail.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: John Stultz <jstultz@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Wang Weiyang <wangweiyang2@huawei.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Cc: Jakob Koschel <jakobkoschel@gmail.com>
Cc: Cai Xinchen <caixinchen1@huawei.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Logan Gunthorpe <logang@deltatee.com>
Link: https://lore.kernel.org/r/2023040250-pushover-platter-509c@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the fixes in here for testing, as well as the driver core
changes for documentation updates to build on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix voltage scaling for chips that have 10.9mV ADCs, where scaling was
not performed.
Fixes: ead8080351 ("hwmon: (it87) Add support for IT8732F")
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20230318080543.1226700-2-frank@crawford.emu.id.au
[groeck: Update subject and description to focus on bug fix]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Smatch reports:
drivers/hwmon/xgene-hwmon.c:757 xgene_hwmon_probe() warn:
'ctx->pcc_comm_addr' from ioremap() not released on line: 757.
This is because in drivers/hwmon/xgene-hwmon.c:701 xgene_hwmon_probe(),
ioremap and memremap is not released, which may cause a leak.
To fix this, ioremap and memremap is modified to devm_ioremap and
devm_memremap.
Signed-off-by: Tianyi Jing <jingfelix@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230318143851.2191625-1-jingfelix@hust.edu.cn
[groeck: Fixed formatting and subject]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It is not sufficient to check of_node in current device.
In some cases, this would cause the sensor registration to fail.
This patch looks for device's ancestors to find a valid of_node if any.
Fixes: d560168b5d ("hwmon: (core) New hwmon registration API")
Signed-off-by: Phinex Hung <phinex@realtek.com>
Link: https://lore.kernel.org/r/20230321060224.3819-1-phinex@realtek.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There is no need to manually set the owner of a struct class, as the
registering function does it automatically, so remove all of the
explicit settings from various drivers that did so as it is unneeded.
This allows us to remove this pointer entirely from this structure going
forward.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Link: https://lore.kernel.org/r/20230313181843.1207845-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ltc2992 drivers uses a mutex and I2C bus access in its GPIO chip `set`
and `get` implementation. This means these functions can sleep and the GPIO
chip should set the `can_sleep` property to true.
This will ensure that a warning is printed when trying to set or get the
GPIO value from a context that potentially can't sleep.
Fixes: 9ca26df1ba ("hwmon: (ltc2992) Add support for GPIOs.")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230314093146.2443845-2-lars@metafoo.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adm1266 driver uses I2C bus access in its GPIO chip `set` and `get`
implementation. This means these functions can sleep and the GPIO chip
should set the `can_sleep` property to true.
This will ensure that a warning is printed when trying to set or get the
GPIO value from a context that potentially can't sleep.
Fixes: d98dfad35c ("hwmon: (pmbus/adm1266) Add support for GPIOs")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230314093146.2443845-1-lars@metafoo.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver will match mostly by DT table (even thought there is regular
ID table) so there is little benefit in of_match_ptr (this also allows
ACPI matching via PRP0001, even though it might not be relevant here).
This also fixes !CONFIG_OF error:
drivers/hwmon/tmp513.c:610:34: error: ‘tmp51x_of_match’ defined but not used [-Werror=unused-const-variable=]
Fixes: 59dfa75e5d ("hwmon: Add driver for Texas Instruments TMP512/513 sensor chips.")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230312193723.478032-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When probing the ucd90320 access to some of the registers randomly fails.
Sometimes it NACKs a transfer, sometimes it returns just random data and
the PEC check fails.
Experimentation shows that this seems to be triggered by a register access
directly back to back with a previous register write. Experimentation also
shows that inserting a small delay after register writes makes the issue go
away.
Use a similar solution to what the max15301 driver does to solve the same
problem. Create a custom set of bus read and write functions that make sure
that the delay is added.
Fixes: a470f11c5b ("hwmon: (pmbus/ucd9000) Add support for UCD90320 Power Sequencer")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230312160312.2227405-1-lars@metafoo.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In xgene_hwmon_probe, &ctx->workq is bound with xgene_hwmon_evt_work.
Then it will be started.
If we remove the driver which will call xgene_hwmon_remove to clean up,
there may be unfinished work.
The possible sequence is as follows:
Fix it by finishing the work before cleanup in xgene_hwmon_remove.
CPU0 CPU1
|xgene_hwmon_evt_work
xgene_hwmon_remove |
kfifo_free(&ctx->async_msg_fifo);|
|
|kfifo_out_spinlocked
|//use &ctx->async_msg_fifo
Fixes: 2ca492e22c ("hwmon: (xgene) Fix crash when alarm occurs before driver probe")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Link: https://lore.kernel.org/r/20230310084007.1403388-1-zyytlz.wz@163.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The wrong bits are masked in the hysteresis register; indices 0 and 2
should zero bits [7:4] and preserve bits [3:0], and index 1 should zero
bits [3:0] and preserve bits [7:4].
Fixes: 1c301fc539 ("hwmon: Add a driver for the ADT7475 hardware monitoring chip")
Signed-off-by: Tony O'Brien <tony.obrien@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20230222005228.158661-3-tony.obrien@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Throughout the ADT7475 driver, attributes relating to the temperature
sensors are displayed in the order Remote 1, Local, Remote 2. Make
temp_st_show() conform to this expectation so that values set by
temp_st_store() can be displayed using the correct attribute.
Fixes: 8f05bcc33e ("hwmon: (adt7475) temperature smoothing")
Signed-off-by: Tony O'Brien <tony.obrien@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20230222005228.158661-2-tony.obrien@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In order to get the thermal zone id but without directly accessing the
thermal zone device structure, add an accessor.
Use the accessor in the hwmon_scmi and acpi_thermal.
No functional change intented.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The thermal zone device structure is exposed to the different drivers
and obviously they access the internals while that should be
restricted to the core thermal code.
In order to self-encapsulate the thermal core code, we need to prevent
the drivers accessing directly the thermal zone structure and provide
accessor functions to deal with.
Use the devdata accessor introduced in the previous patch.
No functional changes intended.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net> #hwmon
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Change MFD support status from Supported to Maintained
- New Drivers
- Add support for the Intel Platform Management Component Interface (PMCI)
- Remove Drivers
- HTC PASIC3 LED/DS1WM
- Toshiba T7L66XB, TC6387XB and TC6393XB TMIO
- New Device Support
- Add support for N6000 Flash to Intel M10 BMC PMCI
- Add support for Lenovo Yoga Tab 3 to Intel CHTWC PMIC
- New Functionality
- Provide Reset support to Syscon
- Fix-ups
- Explicitly provide missing include files
- Pass platform type data/info via the SPI/I2C/DT registration strategy
- Lots of DT documentation / adaptions
- Replace scnprintf() with preferred sysfs_emit()
- Remove unused / superfluous code
- Fix some trivial whitesspace / spelling / grammatical issues
- Replace pm_power_off with new and improved register_sys_off_handler() API
- Bug Fixes
- Reintroduce RK808-clkout registration - fixing Wi-Fi and Bluetooth
- Repair the order of AXPxxx IRQ PEK RISE/FALL definitions
- Refuse to build CS5535 on unsupported UML architectures
- Fix memory leaks in error return paths
- Prevent refcount leaks in error return paths
-----BEGIN PGP SIGNATURE-----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=f0fr
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- Change MFD support status from Supported to Maintained
New Drivers:
- Add support for the Intel Platform Management Component Interface
(PMCI)
Removed Drivers:
- HTC PASIC3 LED/DS1WM
- Toshiba T7L66XB, TC6387XB and TC6393XB TMIO
New Device Support:
- Add support for N6000 Flash to Intel M10 BMC PMCI
- Add support for Lenovo Yoga Tab 3 to Intel CHTWC PMIC
New Functionality:
- Provide Reset support to Syscon
Fix-ups:
- Explicitly provide missing include files
- Pass platform type data/info via the SPI/I2C/DT registration
strategy
- Lots of DT documentation / adaptions
- Replace scnprintf() with preferred sysfs_emit()
- Remove unused / superfluous code
- Fix some trivial whitesspace / spelling / grammatical issues
- Replace pm_power_off with new and improved
register_sys_off_handler() API
Bug Fixes:
- Reintroduce RK808-clkout registration - fixing Wi-Fi and Bluetooth
- Repair the order of AXPxxx IRQ PEK RISE/FALL definitions
- Refuse to build CS5535 on unsupported UML architectures
- Fix memory leaks in error return paths
- Prevent refcount leaks in error return paths"
* tag 'mfd-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (40 commits)
dt-bindings: mfd: qcom,tcsr: Add compatible for IPQ5332
dt-bindings: mfd: Add NXP BBNSM
mfd: ntxec: Add version number for EC in Tolino Vision
dt-bindings: mfd: syscon: Add mt8365-syscfg
mfd: Remove toshiba tmio drivers
mfd: arizona: Use pm_runtime_resume_and_get() to prevent refcnt leak
mfd: syscon: Allow reset control for syscon devices
dt-bindings: mfd/syscon: Add resets property
dt-bindings: mfd: syscon: Add amd,pensando-elba-syscon compatible
dt-bindings: mfd: qcom,tcsr: Add compatible for MSM8226
mfd: simple-mfd-i2c: Fix incoherent comment regarding DT registration
mfd: axp20x: Switch to the sys-off handler API
mfd: core: Spelling s/compement/complement/
mfd: max8925: Remove the unused function irq_to_max8925()
mfd: qcom-pm8xxx: Remove set but unused variable 'rev'
dt-bindings: mfd: syscon: Document GXP register compatible
mfd: twl4030-power: Drop empty platform remove function
mfd: twl: Fix TWL6032 phy vbus detection
mfd: pcf50633-adc: Fix potential memleak in pcf50633_adc_async_read()
MAINTAINERS: Move MFD from a Supported to Maintaied state
...
Updates to the usual drivers (ufs, lpfc, qla2xxx, libsas). The major
core change is a rework to remove the two helpers around
scsi_execute_cmd and use it as the only submission interface along
with other minor fixes and updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCY/Z7BSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfF9AP9HzZaZ
0XumuxjchcJHRntcIAzb9kE62SSWFxBrgZQCtAEAyhAO1zK284esgCa+arkzEC7p
uhxpufQSGnYvbasStsU=
=VsH1
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, lpfc, qla2xxx, libsas).
The major core change is a rework to remove the two helpers around
scsi_execute_cmd and use it as the only submission interface along
with other minor fixes and updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (142 commits)
scsi: ufs: core: Fix an error handling path in ufshcd_read_desc_param()
scsi: ufs: core: Fix device management cmd timeout flow
scsi: aic94xx: Add missing check for dma_map_single()
scsi: smartpqi: Replace one-element array with flexible-array member
scsi: mpt3sas: Fix a memory leak
scsi: qla2xxx: Remove the unused variable wwn
scsi: ufs: core: Fix kernel-doc syntax
scsi: ufs: core: Add hibernation callbacks
scsi: snic: Fix memory leak with using debugfs_lookup()
scsi: ufs: core: Limit DMA alignment check
scsi: Documentation: Correct spelling
scsi: Documentation: Correct spelling
scsi: target: Documentation: Correct spelling
scsi: aacraid: Allocate cmd_priv with scsicmd
scsi: ufs: qcom: dt-bindings: Add SM8550 compatible string
scsi: ufs: ufs-qcom: Clear qunipro_g4_sel for HW version major 5
scsi: ufs: qcom: fix platform_msi_domain_free_irqs() reference
scsi: ufs: core: Enable DMA clustering
scsi: ufs: exynos: Fix the maximum segment size
scsi: ufs: exynos: Fix DMA alignment for PAGE_SIZE != 4096
...
- New drivers
* Infineon TDA38640 Voltage Regulator
* NXP MC34VR500 PMIC
* GXP fan controller
* MPQ7932 Power Management IC
- New chip or board support added to existing drivers
* it87: IT87952E; also other cleanup/improvements
* intel-m10-bmc-hwmon: N6000
* pmbus/max16601: MAX16600
* aquacomputer_d5next: Aquacomputer Aquastream Ultimate, Aquacomputer Poweradjust 3,
Aquacomputer Aquaero
* nct6775: Support for B650/B660/X670 ASUS boards
* oxp-sensors: AYANEO AIR and AIR Pro
- Other notable changes
* Various kernel documentation fixes
* Various devicetree bindings fixes
* Explicitly deprecated [devm_]hwmon_device_register_with_groups
* ftsteutates: Support for fanX_fault and other cleanup
* ltc2945: Support for setting shunt resistor and other cleanup/fixes
* coretemp: Avoid RDMSR interrupts to isolated CPUs,
and simplify platform device handling
- Vaious other minoc cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=yXoY
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New drivers:
- Infineon TDA38640 Voltage Regulator
- NXP MC34VR500 PMIC
- GXP fan controller
- MPQ7932 Power Management IC
New chip or board support added to existing drivers:
- it87: IT87952E; also other cleanup/improvements
- intel-m10-bmc-hwmon: N6000
- pmbus/max16601: MAX16600
- aquacomputer_d5next: Aquacomputer Aquastream Ultimate, Aquacomputer
Poweradjust 3, Aquacomputer Aquaero
- nct6775: Support for B650/B660/X670 ASUS boards
- oxp-sensors: AYANEO AIR and AIR Pro
Other notable changes:
- Various kernel documentation fixes
- Various devicetree bindings fixes
- Explicitly deprecated [devm_]hwmon_device_register_with_groups
- ftsteutates: Support for fanX_fault and other cleanup
- ltc2945: Support for setting shunt resistor and other cleanup/fixes
- coretemp: Avoid RDMSR interrupts to isolated CPUs, and simplify
platform device handling
... and various other minor cleanups and fixes"
* tag 'hwmon-for-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (66 commits)
hwmon: Deprecate [devm_]hwmon_device_register_with_groups
hwmon: (mlxreg-fan) Return zero speed for broken fan
hwmon: (gxp-fan-ctrl) use devm_platform_get_and_ioremap_resource()
hwmon: (aquacomputer_d5next) Add support for Aquacomputer Aquastream Ultimate
hwmon: (aquacomputer_d5next) Add support for Aquacomputer Poweradjust 3
hwmon: (iio_hwmon) use dev_err_probe
hwmon: intel-m10-bmc-hwmon: Add N6000 sensors
Docs/hwmon/index: Add missing SPDX License Identifier
hwmon: (it87) Updated documentation for recent updates to it87
hwmon: (it87) Add new chipset IT87952E
hwmon: (it87) Allow multiple chip IDs for force_id
hwmon: (it87) Add chip_id in some info message
hwmon: (it87) List full chip model name
hwmon: (it87) Disable configuration exit for certain chips
hwmon: (it87) Allow disabling exiting of configuration mode
Documentation: hwmon: correct spelling
hwmon: (pmbus/max16601) Add support for MAX16600
hwmon: (ltc2945) Allow setting shunt resistor
hwmon: (ltc2945) Handle error case in ltc2945_value_store
hwmon: (ltc2945) Add devicetree match table
...
Currently for broken fan driver returns value calculated based on error
code (0xFF) in related fan speed register.
Thus, for such fan user gets fan{n}_fault to 1 and fan{n}_input with
misleading value.
Add check for fan fault prior return speed value and return zero if
fault is detected.
Fixes: 65afb4c8e7 ("hwmon: (mlxreg-fan) Add support for Mellanox FAN driver")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20230212145730.24247-1-vadimp@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/202302081546067270324@zte.com.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose various hardware sensors of the
Aquacomputer Aquastream Ultimate watercooling pump, which communicates
through a proprietary USB HID protocol.
Coolant temp and external temp sensor readings are available, along with
speed, power, voltage and current of both the pump and optionally connected
fan. It also exposes pressure and flow speed readings.
Additionally, serial number and firmware version are exposed through
debugfs.
Tested by a user on Github [1].
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/issues/50
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20230203120324.579808-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose the temp sensor of the
Aquacomputer Poweradjust 3 fan controller, which communicates
through a proprietary USB HID protocol.
The Poweradjust 3 is not currently known to expose firmware version
and serial number, so don't create debugfs entries if their values
can't be retrieved.
Tested by a user on Github [1].
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/issues/57
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20230131101210.8095-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Instead of just returning an error code, add an error message as well.
While at it, simplify the code and use a common return path.
Upon deferral this also nicely lists the following message in
/sys/kernel/debug/devices_deferred:
adc iio_hwmon: Failed to get channels
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20230131103359.625081-1-alexander.stein@ew.tq-group.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add IT87952E, a new chip ID (DEV ID 0x8695), which appears to be an
updated version of the IT8792E and takes the same configuration.
The model name comes from the model name printed on the chip.
There is no datasheet publicly available.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20230128060308.1549707-7-frank@crawford.emu.id.au
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend the force_id module parameter to allow specifying one or both
chip IDs separately. If only a single parameter is given it defaults
to using that value for all chips, similar to previous usage.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20230128060308.1549707-6-frank@crawford.emu.id.au
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ITE model names do not always match the chip ID.
Convert from just adding a suffix to specifying the full model name.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20230128060308.1549707-4-frank@crawford.emu.id.au
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8790E and IT8792E/IT8795E have been identified as chips that can have
issues when disabling configuration mode.
Set to never exit configuration mode.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20230128060308.1549707-3-frank@crawford.emu.id.au
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Disabling configuration mode on some chips can result in system
hang-ups and access failures to the Super-IO chip at the
second SIO address. Never exit configuration mode on these
chips to avoid the problem.
This patch should be applied in conjunction with a previous one to
initialise the second chip for certain mother boards.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20230128060308.1549707-2-frank@crawford.emu.id.au
[groeck: Change feature bit from 28 to 19 to be continuous]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
From programming perspective, MAX16600 is identical to MAX16601 and
MAX16602. Add support for it.
Cc: Steve Foreman <foremans@google.com>
Cc: Holly Barrett <holly.barrett@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the ability to specify the value of the shunt resistor in the
device tree instead of assuming it is 1 milliOhm. The value in the
device tree has the name shunt-resistor-micro-ohms and the
default value is 1000 micro-ohms in order to preserve the
current behavior.
Signed-off-by: Jonathan Cormier <jcormier@criticallink.com>
Signed-off-by: John Pruitt <jpruitt@criticallink.com>
[groeck: Fixed multi-line alignment, squashed last patch of series]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ltc2945_val_to_reg errors were not being handled
which would have resulted in register being set to
0 (clamped) instead of being left alone.
Fixes: 6700ce035f ("hwmon: Driver for Linear Technologies LTC2945")
Signed-off-by: Jonathan Cormier <jcormier@criticallink.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the pmbus driver for the Infineon TDA38640 voltage regulator.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20230124202317.3704963-2-Naresh.Solanki@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Group the MODULE_PARM definitions together to make them easier for
future maintenance, rather than having them spread across the file.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20230121085754.1693336-2-frank@crawford.emu.id.au
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver knows internally when a fan is not connected,
but does not export this knowledge to userspace. Use the
standard fanX_fault attributes to notify userspace if a
fan is not connected.
Tested on a Fujitsu DS3401-B1.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230105225107.58308-4-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Replace the nonstandard fanX_source attributes with the standardized
pwmX_auto_channels_temp attributes and document the special behaviour
associated with those attributes.
Tested on a Fujitsu DS3401-B1.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230105225107.58308-3-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert driver to use devm_hwmon_device_register_with_info()
to reduce module size by ~30%.
Tested on a Fujitsu DS3401-B1.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230105225107.58308-2-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On various Gigabyte AM4 boards (AB350, AX370), the second Super-IO chip
(IT8792E) needs to be in configuration mode before accessing the first
due to a bug in IT8792E which otherwise results in LPC bus access errors.
This needs to be done before accessing the first Super-IO chip since
the second chip may have been accessed prior to loading this driver.
The problem is also reported to affect IT8795E, which is used on X299
boards and has the same chip ID as IT8792E (0x8733). It also appears
to affect systems with IT8790E, which is used on some Z97X-Gaming boards
as well as Z87X-OC, and other more recent Gigabyte boards.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20230104060926.619686-3-frank@crawford.emu.id.au
[groeck: Made description pass checkpatch]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Allow for superio_enter to be called without requesting the muxed memory
region, in particular for initialisation of the second chipset, which must
be put into configuration mode, but without an associated call to leave
configuration mode.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20230104060926.619686-2-frank@crawford.emu.id.au
[groeck: Clarified subject]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
New ASUS B650/B660/X670 boards firmware have not exposed WMI monitoring
GUID and entrypoint method WMBD could be implemented for different device
UID.
Implement the direct call to entrypoint method for monitoring the device
UID of B550/X570 boards.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204807
Signed-off-by: Denis Pauk <pauk.denis@gmail.com>
Co-developed-by: Ahmad Khalifa <ahmad@khalifa.ws>
Signed-off-by: Ahmad Khalifa <ahmad@khalifa.ws>
Link: https://lore.kernel.org/r/20230111212241.7456-1-pauk.denis@gmail.com
[groeck: Fix multi-line formatting]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use the correct function name in kernel-doc comments to prevent these
warnings:
drivers/hwmon/hih6130.c:164: warning: expecting prototype for hih6130_show_temperature(). Prototype was for hih6130_temperature_show() instead
drivers/hwmon/hih6130.c:185: warning: expecting prototype for hih6130_show_humidity(). Prototype was for hih6130_humidity_show() instead
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Link: https://lore.kernel.org/r/20230113064549.21289-1-rdunlap@infradead.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use the correct function names in kernel-doc comments to prevent these
warnings:
drivers/hwmon/sht15.c:682: warning: expecting prototype for sht15_show_status(). Prototype was for sht15_status_show() instead
drivers/hwmon/sht15.c:705: warning: expecting prototype for sht15_store_heater(). Prototype was for sht15_status_store() instead
drivers/hwmon/sht15.c:738: warning: expecting prototype for sht15_show_temp(). Prototype was for sht15_temp_show() instead
drivers/hwmon/sht15.c:760: warning: expecting prototype for sht15_show_humidity(). Prototype was for sht15_humidity_show() instead
drivers/hwmon/sht21.c:128: warning: expecting prototype for sht21_show_temperature(). Prototype was for sht21_temperature_show() instead
drivers/hwmon/sht21.c:149: warning: expecting prototype for sht21_show_humidity(). Prototype was for sht21_humidity_show() instead
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Link: https://lore.kernel.org/r/20230113064556.21685-1-rdunlap@infradead.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix kernel-doc warnings:
drivers/hwmon/emc2305.c:62: warning: Cannot understand * @cdev: cooling device;
on line 62 - I thought it was a doc line
drivers/hwmon/emc2305.c:89: warning: Cannot understand * @client: i2c client;
on line 89 - I thought it was a doc line
and drop ';' at end of each struct member line.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Link: https://lore.kernel.org/r/20230113064540.20179-1-rdunlap@infradead.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The GXP SoC can support up to 16 fans through the interface provided by
the CPLD. The current support is limited to 8 fans. The fans speeds are
controlled via 8 different PWMs which can vary in value from 0-255. The
fans are also capable of reporting if they have failed to the CPLD which
in turn reports the status to the GXP SoC.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Link: https://lore.kernel.org/r/20230103203654.59322-2-nick.hawkins@hpe.com
[groeck: Improved alignment of defined, added missing include linux/bits.h]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Coretemp's platform driver is unconventional. All the real work is done
globally by the initcall and CPU hotplug notifiers, while the "driver"
effectively just wraps an allocation and the registration of the hwmon
interface in a long-winded round-trip through the driver core. The whole
logic of dynamically creating and destroying platform devices to bring
the interfaces up and down is error prone, since it assumes
platform_device_add() will synchronously bind the driver and set drvdata
before it returns, thus results in a NULL dereference if drivers_autoprobe
is turned off for the platform bus. Furthermore, the unusual approach of
doing that from within a CPU hotplug notifier, already commented in the
code that it deadlocks suspend, also causes lockdep issues for other
drivers or subsystems which may want to legitimately register a CPU
hotplug notifier from a platform bus notifier.
All of these issues can be solved by ripping this unusual behaviour out
completely, simply tying the platform devices to the lifetime of the
module itself, and directly managing the hwmon interfaces from the
hotplug notifiers. There is a slight user-visible change in that
/sys/bus/platform/drivers/coretemp will no longer appear, and
/sys/devices/platform/coretemp.n will remain present if package n is
hotplugged off, but hwmon users should really only be looking for the
presence of the hwmon interfaces, whose behaviour remains unchanged.
Link: https://lore.kernel.org/lkml/20220922101036.87457-1-janusz.krzysztofik@linux.intel.com/
Link: https://gitlab.freedesktop.org/drm/intel/issues/6641
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Link: https://lore.kernel.org/r/20230103114620.15319-1-janusz.krzysztofik@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for reading four calculated virtual temp sensors on the
Aquacomputer Aquaero. Values of these sensors are calculated on the
device itself based on what the user configured in the official software.
Configuring these sensors is not currently reverse engineered.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20230101190056.1357124-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make the description of @aht10_data to @data in aht10_read_values()
and remove @client in aht10_init() to clear the below warnings:
drivers/hwmon/aht10.c:87: warning: Excess function parameter 'client' description in 'aht10_init'
drivers/hwmon/aht10.c:131: warning: Function parameter or member 'data' not described in 'aht10_read_values'
drivers/hwmon/aht10.c:131: warning: Excess function parameter 'aht10_data' description in 'aht10_read_values'
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3543
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20221223081056.88345-1-yang.lee@linux.alibaba.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_watchdog_register_device() to let devres take care
of unregistering the watchdog at device removal. Remove the
now pointless fts_remove() function.
Tested on a Fujitsu DS3401-B1.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20221224041855.83981-4-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the AYANEO AIR and AYANEO AIR Pro models of handheld
devices. These devices use the same EC registers and logic as the One X
Player mini AMD. Previous AYANEO models are not supported as they use a
different EC and do not have the necessary fan speed write enable and
setting registers. The driver is tested on AYANEO AIR while AIR Pro model
EC functionality and DMI data were verified using command line tools by
another user.
Add:
- AYANEO AIR (AMD 5560U)
- AYANEO AIR Pro (AMD 5560U)
- AYANEO AIR Pro (AMD 5825U)
While at it, fix spelling error (appart -> apart).
Link: https://lore.kernel.org/r/20221229025609.147482-1-derekjohn.clark@gmail.com
Signed-off-by: Derek J. Clark <derekjohn.clark@gmail.com>
[groeck: Sanitize commit description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add device dependent serial number and firmware offsets to support
devices with different offsets. All currently supported devices share
the same offsets. Implemented by Aleksa Savic [1].
[1] 14c3acf78b
Originally-from: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
Link: https://lore.kernel.org/r/20221218113131.3752-5-leonard.anderweit@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Introduce structure for per device fan sensor offsets. This allows
reading fan sensors in aqc_raw_event() from devices which use a
different sensor layout in their status HID report. Currently only one
version is implemented as all supported devices use the same structure.
Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
Link: https://lore.kernel.org/r/20221218113131.3752-4-leonard.anderweit@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Read flow sensors the same way for all devices instead of in special
cases. Implemented by Aleksa Savic [1].
[1] 1c10912c5f
Originally-from: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
Link: https://lore.kernel.org/r/20221218113131.3752-3-leonard.anderweit@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The MPQ7932 is a power management IC designed to operate from 5V buses to
power a variety of Advanced driver-assistance system SOCs. Six integrated
buck converters with hardware monitoring capability powers a variety of
target rails configurable over PMBus interface.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
Link: https://lore.kernel.org/r/20221207173716.123223-4-saravanan@linumiz.com
[groeck: Modified multi-line comments to match standard comment style]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The coretemp driver uses rdmsr_on_cpu calls to read
MSR_IA32_PACKAGE_THERM_STATUS/MSR_IA32_THERM_STATUS registers,
which contain information about current core temperature.
For certain low latency applications, the RDMSR interruption exceeds
the applications requirements.
So do not create core files in sysfs, for CPUs which have
isolation and nohz_full enabled.
Temperature information from the housekeeping cores should be
sufficient to infer die temperature.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Link: https://lore.kernel.org/r/Y5zT6B1mY9/pnwJV@tpad
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The find_last_bit() call produces the index of the highest-numbered
core in core_mask; because cores are numbered from zero, the number of
elements we need to allocate is one more than that.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Cc: stable@kernel.org # v5.18
Fixes: bf3608f338 ("hwmon: peci: Add cputemp driver")
Reviewed-by: Iwona Winiarska <iwona.winiarska@intel.com>
Link: https://lore.kernel.org/r/20230202021825.21486-1-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Split the common code from intel-m10-bmc driver into intel-m10-bmc-core
and move the SPI bus parts into an interface specific file.
intel-m10-bmc-core becomes the core MFD functions which can support
multiple bus interface like SPI bus.
Co-developed-by: Tianfei zhang <tianfei.zhang@intel.com>
Signed-off-by: Tianfei zhang <tianfei.zhang@intel.com>
Reviewed-by: Russ Weight <russell.h.weight@intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net> # hwmon
Reviewed-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230116100845.6153-5-ilpo.jarvinen@linux.intel.com
The s3c adc driver was removed along with the s3c24xx platform, so the
hwmon driver is orphaned and can be removed.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
scsi_execute_req() is going to be removed. Convert drivetemp to
scsi_execute_cmd().
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 4ef2774511 ("hwmon: (nct6775) Convert register access to
regmap API") fumbled the shifting & masking of the fan_div values such
that odd-numbered fan divisors would always be set to zero. Fix it so
that we actually OR in the bits we meant to.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 4ef2774511 ("hwmon: (nct6775) Convert register access to regmap API")
Cc: stable@kernel.org # v5.19+
Link: https://lore.kernel.org/r/20230102212857.5670-1-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A user complained that the ftsteutates driver was displaying
bogus values since its introduction. This happens because the
sensor measurements need to be scaled in order to produce
meaningful results:
- the fan speed needs to be multiplied by 60 since its in RPS
- the temperature is in degrees celsius and needs an offset of 64
- the voltage is in 1/256 of 3.3V
The offical datasheet says the voltage needs to be divided by 256,
but this is likely an off-by-one-error, since even the BIOS
devides by 255 (otherwise 3.3V could not be measured).
The voltage channels additionally need a board-specific multiplier,
however this can be done by the driver since its board-specific.
The reason the missing scaling of measurements is the way Fujitsu
used this driver when it was still out-of-tree. Back then, all
scaling was done in userspace by libsensors, even the generic one.
Tested on a Fujitsu DS3401-B1.
Fixes: 08426eda58 ("hwmon: Add driver for FTS BMC chip "Teutates"")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20221224041855.83981-2-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
New drivers
- Driver for OneXPlayer mini AMD sensors
- Ampere's Altra smpro-hwmon driver
New chip and attribute support in existing drivers
- nct6775: Support for ASUS CROSSHAIR VIII/TUF/ProArt B550M
- pmbus/ltc2978: Support for LTC7132
- aquacomputer_d5next: Support for temperature sensor offsets
and flow sensor pulses
- coretemp: Support for dynamic ttarget and tjmax
Improvements
- Use devm_regulator_get_enable() where appropriate
- Use sysfs_emit() instead of scnprintf()
- Remove some useless #include <linux/hwmon-vid.h>
- Include <linux/kstrtox.h> when appropriate
- Use simple i2c probe
- it87: Check for a valid chip before using force_id, and new
new module parameter to ignore ACPI resource conflicts
- jc42: Use regmap, and restore min/max/critical temperatures on resume
- Add reporting power good and status to PMBus based regulators
Last minute fixes
- emc2305: Fix probing of emc2301/2/3, and fix setting pwm values
manually if THERMAL is enabled
Various other minor fixes and improvements
-----BEGIN PGP SIGNATURE-----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=O7h4
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New drivers:
- Driver for OneXPlayer mini AMD sensors
- Ampere's Altra smpro-hwmon driver
New chip and attribute support in existing drivers:
- nct6775: Support for ASUS CROSSHAIR VIII/TUF/ProArt B550M
- pmbus/ltc2978: Support for LTC7132
- aquacomputer_d5next: Support for temperature sensor offsets and
flow sensor pulses
- coretemp: Support for dynamic ttarget and tjmax
Improvements:
- Use devm_regulator_get_enable() where appropriate
- Use sysfs_emit() instead of scnprintf()
- Remove some useless #include <linux/hwmon-vid.h>
- Include <linux/kstrtox.h> when appropriate
- Use simple i2c probe
- it87: Check for a valid chip before using force_id, and new new
module parameter to ignore ACPI resource conflicts
- jc42: Use regmap, and restore min/max/critical temperatures on
resume
- Add reporting power good and status to PMBus based regulators
Last minute fixes:
- emc2305: Fix probing of emc2301/2/3, and fix setting pwm values
manually if THERMAL is enabled
And various other minor fixes and improvements"
* tag 'hwmon-for-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (37 commits)
hwmon: (emc2305) fix pwm never being able to set lower
hwmon: (emc2305) fix unable to probe emc2301/2/3
hwmon: (dell-smm) Move error message to make probing silent
hwmon: use sysfs_emit() to instead of scnprintf()
hwmon: (oxp-sensors) Fix pwm reading
hwmon: (aquacomputer_d5next) Add support for Quadro flow sensor pulses
hwmon: (pmbus/core) Implement regulator get_status
hwmon: (oxp-sensors) Add AOK ZOE and Mini PRO
hwmon: (gsc-hwmon) Switch to flexible array to simplify code
hwmon: (pmbus) Add power good support
hwmon: (nct6775) add ASUS CROSSHAIR VIII/TUF/ProArt B550M
hwmon: (coretemp) Add support for dynamic ttarget
hwmon: (coretemp) Add support for dynamic tjmax
hwmon: (coretemp) rearrange tjmax handing code
hwmon: Remove some useless #include <linux/hwmon-vid.h>
hwmon: (coretemp) Remove obsolete temp_data->valid
hwmon: add OneXPlayer mini AMD sensors driver
hwmon: (aquacomputer_d5next) Clear up macros and comments
hwmon: (it87) Add DMI table for future extensions
hwmon: Include <linux/kstrtox.h> when appropriate
...
Merge ACPI changes related to device enumeration, device object
managenet, operation region handling, table parsing and sysfs
interface:
- Use ZERO_PAGE(0) instead of empty_zero_page in the ACPI device
enumeration code (Giulio Benetti).
- Change the return type of the ACPI driver remove callback to void and
update its users accordingly (Dawei Li).
- Add general support for FFH address space type and implement the low-
level part of it for ARM64 (Sudeep Holla).
- Fix stale comments in the ACPI tables parsing code and make it print
more messages related to MADT (Hanjun Guo, Huacai Chen).
- Replace invocations of generic library functions with more kernel-
specific counterparts in the ACPI sysfs interface (Christophe JAILLET,
Xu Panda).
* acpi-scan:
ACPI: scan: substitute empty_zero_page with helper ZERO_PAGE(0)
* acpi-bus:
ACPI: FFH: Silence missing prototype warnings
ACPI: make remove callback of ACPI driver void
ACPI: bus: Fix the _OSC capability check for FFH OpRegion
arm64: Add architecture specific ACPI FFH Opregion callbacks
ACPI: Implement a generic FFH Opregion handler
* acpi-tables:
ACPI: tables: Fix the stale comments for acpi_locate_initial_tables()
ACPI: tables: Print CORE_PIC information when MADT is parsed
* acpi-sysfs:
ACPI: sysfs: use sysfs_emit() to instead of scnprintf()
ACPI: sysfs: Use kstrtobool() instead of strtobool()
There are fields 'last_hwmon_state' and 'last_thermal_state' in the
structure 'emc2305_cdev_data', which respectively store the cooling state
set by the 'hwmon' and 'thermal' subsystem, and the driver author hopes
that if the state set by 'hwmon' is lower than the value set by 'thermal',
the driver will just save it without actually setting the pwm. Currently,
the 'last_thermal_state' also be updated by 'hwmon', which will cause the
cooling state to never be set to a lower value. This patch fixes that.
Signed-off-by: Xingjiang Qiao <nanpuyue@gmail.com>
Link: https://lore.kernel.org/r/20221206055331.170459-2-nanpuyue@gmail.com
Fixes: 0d8400c5a2 ("hwmon: (emc2305) add support for EMC2301/2/3/5 RPM-based PWM Fan Speed Controller.")
[groeck: renamed emc2305_set_cur_state_shim -> __emc2305_set_cur_state]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The definitions of 'EMC2305_REG_PRODUCT_ID' and 'EMC2305_REG_DEVICE' are
both '0xfd', they actually return the same value, but the values returned
by emc2301/2/3/5 are different, so probe emc2301/2/3 will fail, This patch
fixes that.
Signed-off-by: Xingjiang Qiao <nanpuyue@gmail.com>
Link: https://lore.kernel.org/r/20221206055331.170459-1-nanpuyue@gmail.com
Fixes: 0d8400c5a2 ("hwmon: (emc2305) add support for EMC2301/2/3/5 RPM-based PWM Fan Speed Controller.")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If dell-smm-hwmon loads on unsupported hardware like the
Dell XPS 17 9710, an error message is printed.
This might confuse users, as drivers are expected to be
silent if no supported hardware is found.
Reorder the error message so its only printed when the
driver is loaded with the "force" option being set.
Also reword the error message slightly.
Tested on a Dell Inspiron 3505.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20221130183418.357246-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the AOK ZOE A1 and OXP Mini PRO handheld devices.
DMI strings are added to this driver since the same EC layout is used and
has similar specs as the OXP mini AMD.
The added devices are:
- OneXPlayer mini PRO (AMD 6800U)
- AOK ZOE A1 (AMD 6800U)
Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com>
Link: https://lore.kernel.org/r/20221125114901.11309-1-samsagax@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using flexible array is more straight forward. It
- saves 1 pointer in the 'gsc_hwmon_platform_data' structure
- saves an indirection when using this array
- saves some LoC and avoids some always spurious pointer arithmetic
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/61a23e1d642397cfcecc4ac3bb0ab485d257987d.1668936855.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Update error flags with regulation out if regulator is on & power
good status bit is set
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20221117184022.1808508-1-Naresh.Solanki@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Boards such as
* ProArt B550-CREATOR
* ProArt Z490-CREATOR 10G
* ROG CROSSHAIR VIII EXTREME
* ROG CROSSHAIR VIII HERO (WI-FI)
* TUF GAMING B550M-E
* TUF GAMING B550M-E (WI-FI)
* TUF GAMING B550M-PLUS WIFI II
have got a nct6775 chip, but by default there's no use of it
because of resource conflict with WMI method.
This commit adds such boards to the WMI monitoring list.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204807
Signed-off-by: Denis Pauk <pauk.denis@gmail.com>
Reported-by: yutesdb <mundanedefoliation@gmail.com>
Tested-by: yutesdb <mundanedefoliation@gmail.com>
Link: https://lore.kernel.org/r/20221114214456.3891-1-pauk.denis@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tjmax value retrieved from MSR_IA32_TEMPERATURE_TARGET can be changed at
runtime when the Intel SST-PP (Intel Speed Select Technology -
Performance Profile) level is changed. As a result, the ttarget value
also becomes dyamic.
Improve the code to always get updated ttarget value.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20221113153145.32696-4-rui.zhang@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tjmax value retrieved from MSR_IA32_TEMPERATURE_TARGET can be changed at
runtime when the Intel SST-PP (Intel Speed Select Technology -
Performance Profile) level is changed.
Improve the code to always use updated tjmax when it can be retrieved
from MSR_IA32_TEMPERATURE_TARGET.
When tjmax can not be retrieved from MSR_IA32_TEMPERATURE_TARGET, still
follow the previous logic and always use a static tjmax value.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20221113153145.32696-3-rui.zhang@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rearrange the tjmax handling code so that it can be used directly in
the sysfs attribute callbacks without forward declarations.
No functional change in this patch.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20221113153145.32696-2-rui.zhang@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Checking for the valid bit of IA32_THERM_STATUS is removed in commit
bf6ea084eb ("hwmon: (coretemp) Do not return -EAGAIN for low
temperatures"), and temp_data->valid is set and never cleared when the
temperature has been read once.
Remove the obsolete temp_data->valid field.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20221108075051.5139-2-rui.zhang@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Sensors driver for OXP Handhelds from One-Netbook that expose fan reading
and control via hwmon sysfs.
As far as I could gather all OXP boards have the same DMI strings and
they can be told appart only by the boot cpu vendor (Intel/AMD).
Currently only AMD boards are supported since Intel have different EC
registers and values to read/write.
Fan control is provided via pwm interface in the range [0-255]. AMD
boards have [0-100] as range in the EC, the written value is scaled to
accommodate for that.
Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com>
Link: https://lore.kernel.org/r/20221104140659.593608-1-samsagax@gmail.com
[groeck: Removed misleading comment about module_platform_driver()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reorganize macro definitions into sections for each supported
device, with additional comments on their purpose. This should
make it easier to follow what report each offset is coming
from. Also, reformat per-device initializations in
aqc_probe() to organize them into sections (fan info,
temp sensors, other parameters and lastly labels).
No functional changes.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20221107142455.655998-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add in DMI matching table to match various board quirks and settings.
This will be useful for future extentions, but will start with the
existing definition of the Shuttle SN68PT.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20221105232531.1619387-1-frank@crawford.emu.id.au
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use BIT() and GENMASK() macros for defining the bitfields inside the
registers. Also use FIELD_GET() and FIELD_PREP() where appropriate. This
makes the coding style within the driver consistent. No functional
changes intended.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for LTC7132.
The relevant registers in the LTC7132 are identical to the LTC7880.
So it's just a matter of adding the chip id.
Signed-off-by: Felix Nieuwenhuizen <Felix.Nieuwenhuizen@etas.com>
Link: https://lore.kernel.org/r/20221027145135.31802-1-Felix.Nieuwenhuizen@etas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Clang warns:
drivers/hwmon/smpro-hwmon.c:378:2: error: unannotated fall-through between switch labels [-Werror,-Wimplicit-fallthrough]
default:
^
drivers/hwmon/smpro-hwmon.c:378:2: note: insert 'break;' to avoid fall-through
default:
^
break;
1 error generated.
Clang is a little more pedantic than GCC, which does not warn when
falling through to a case that is just break or return. Clang's version
is more in line with the kernel's own stance in deprecated.rst, which
states that all switch/case blocks must end in either break,
fallthrough, continue, goto, or return.
Add the missing break to silence the warning. Additionally, adjust the
indentation of a break and add a default case to the inner switch
statement.
Fixes: a87456864cbb ("hwmon: Add Ampere's Altra smpro-hwmon driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1751
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20221027231611.3824800-1-nathan@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the missing unlock before return from function jc42_write()
in the error handling case.
Fixes: 37dedaee8bc6 ("hwmon: (jc42) Convert register access and caching to regmap/regcache")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221027062931.598247-1-yangyingliang@huawei.com
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The JC42 compatible thermal sensor on Kingston KSM32ES8/16ME DIMMs
(using Micron E-Die) is an ST Microelectronics STTS2004 (manufacturer
0x104a, device 0x2201). It does not keep the previously programmed
minimum, maximum and critical temperatures after system suspend and
resume (which is a shutdown / startup cycle for the JC42 temperature
sensor). This results in an alarm on system resume because the hardware
default for these values is 0°C (so any environment temperature greater
than 0°C will trigger the alarm).
Example before system suspend:
jc42-i2c-0-1a
Adapter: SMBus PIIX4 adapter port 0 at 0b00
temp1: +34.8°C (low = +0.0°C)
(high = +85.0°C, hyst = +85.0°C)
(crit = +95.0°C, hyst = +95.0°C)
Example after system resume (without this change):
jc42-i2c-0-1a
Adapter: SMBus PIIX4 adapter port 0 at 0b00
temp1: +34.8°C (low = +0.0°C) ALARM (HIGH, CRIT)
(high = +0.0°C, hyst = +0.0°C)
(crit = +0.0°C, hyst = +0.0°C)
Apply the cached values from the JC42_REG_TEMP_UPPER,
JC42_REG_TEMP_LOWER, JC42_REG_TEMP_CRITICAL and JC42_REG_SMBUS (where
the SMBUS register is not related to this issue but a side-effect of
using regcache_sync() during system resume with the previously
cached/programmed values. This fixes the alarm due to the hardware
defaults of 0°C because the previously applied limits (set by userspace)
are re-applied on system resume.
Fixes: 175c490c9e ("hwmon: (jc42) Add support for STTS2004 and AT30TSE004")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221023213157.11078-3-martin.blumenstingl@googlemail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Switch the jc42 driver to use an I2C regmap to access the registers.
Also move over to regmap's built-in caching instead of adding a
custom caching implementation. This works for JC42_REG_TEMP_UPPER,
JC42_REG_TEMP_LOWER and JC42_REG_TEMP_CRITICAL as these values never
change except when explicitly written. The cache For JC42_REG_TEMP is
dropped (regmap can't cache it because it's volatile, meaning it can
change at any time) as well for simplicity and consistency with other
drivers.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221023213157.11078-2-martin.blumenstingl@googlemail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit c112d75840 ("hwmon: OCC drivers are ARM-only") made the OCC
sensor drivers not selectable on powerpc64:
These drivers are for a BMC inside PowerPC servers. The BMC runs on
ARM hardware, so only propose the drivers on this architecture, unless
build-testing.
... but we now have a powerpc64 BMC (still for a powerpc64 host), so
drop the `depends on` that excludes building for this platform.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20221024081527.3842565-1-jk@codeconstruct.com.au
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This commit adds support for Ampere SMpro hwmon driver. This driver
supports accessing various CPU sensors provided by the SMpro co-processor
including temperature, power, voltages, and current.
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Link: https://lore.kernel.org/r/20220929094321.770125-2-quan@os.amperecomputing.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Drop open-coded pattern: 'devm_regulator_get(), regulator_enable(),
add_action_or_reset(regulator_disable)' and use the
devm_regulator_get_enable() and drop the pointer to the regulator.
This simplifies code and makes it less tempting to add manual control
for the regulator which is also controlled by devm.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/7773541795f280db31dd981ffc21df8a630b794a.1666357434.git.mazziesaccount@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All these drivers have an i2c probe function which doesn't use the
"struct i2c_device_id *id" parameter, so they can trivially be
converted to the "probe_new" style of probe with a single argument.
This is part of an ongoing transition to single-argument i2c probe
functions. Old-style probe functions involve a call to i2c_match_id:
in drivers/i2c/i2c-core-base.c,
/*
* When there are no more users of probe(),
* rename probe_new to probe.
*/
if (driver->probe_new)
status = driver->probe_new(client);
else if (driver->probe)
status = driver->probe(client,
i2c_match_id(driver->id_table, client));
else
status = -EINVAL;
Drivers which don't need the second parameter can be declared using
probe_new instead, avoiding the call to i2c_match_id. Drivers which do
can still be converted to probe_new-style, calling i2c_match_id
themselves (as is done currently for of_match_id).
This change was done using the following Coccinelle script, and fixed
up for whitespace changes:
@ rule1 @
identifier fn;
identifier client, id;
@@
- static int fn(struct i2c_client *client, const struct i2c_device_id *id)
+ static int fn(struct i2c_client *client)
{
...when != id
}
@ rule2 depends on rule1 @
identifier rule1.fn;
identifier driver;
@@
struct i2c_driver driver = {
- .probe
+ .probe_new
=
(
fn
|
- &fn
+ fn
)
,
};
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20221011143309.3141267-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Check there is a chip before using force_id parameter as there
is no value in registering a non-existent chip
Signed-off-by: Ahmad Khalifa <ahmad@khalifa.ws>
Link: https://lore.kernel.org/r/20221004210100.540120-3-ahmad@khalifa.ws
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add parameter to ignore ACPI resource conflicts as an alternate to using
'acpi_enforce_resources=lax'.
Some BIOSes reserve resources and don't use them and the system wide
parameter may result in failures to certain drivers.
Signed-off-by: Ahmad Khalifa <ahmad@khalifa.ws>
Link: https://lore.kernel.org/r/20221004210100.540120-2-ahmad@khalifa.ws
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Don't populate the read-only const arrays names and watchdog_minors
on the stack but instead make them static const. Also makes the
object code a little smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20221005152752.318493-1-colin.i.king@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As the devm_kcalloc may return NULL, the return value needs to be checked
to avoid NULL poineter dereference.
Fixes: d0ddfd241e ("hwmon: (asus-ec-sensors) add driver for ASUS EC")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20221125014329.121560-1-yuancan@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put(). So call it after using to avoid refcount leak.
Fixes: 14513ee696 ("hwmon: (coretemp) Use PCI host bridge ID to identify CPU if necessary")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221118093303.214163-1-yangyingliang@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For bus-based driver, device removal is implemented as:
1 device_remove()->
2 bus->remove()->
3 driver->remove()
Driver core needs no inform from callee(bus driver) about the
result of remove callback. In that case, commit fc7a6209d5
("bus: Make remove callback return void") forces bus_type::remove
be void-returned.
Now we have the situation that both 1 & 2 of calling chain are
void-returned, so it does not make much sense for 3(driver->remove)
to return non-void to its caller.
So the basic idea behind this change is making remove() callback of
any bus-based driver to be void-returned.
This change, for itself, is for device drivers based on acpi-bus.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dawei Li <set_pte_at@outlook.com>
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for drivers/platform/surface/*
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Smatch report warning as follows:
drivers/hwmon/ibmpex.c:509 ibmpex_register_bmc() warn:
'&data->list' not removed from list
If ibmpex_find_sensors() fails in ibmpex_register_bmc(), data will
be freed, but data->list will not be removed from driver_data.bmc_data,
then list traversal may cause UAF.
Fix by removeing it from driver_data.bmc_data before free().
Fixes: 57c7c3a0fd ("hwmon: IBM power meter driver")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Link: https://lore.kernel.org/r/20221117034423.2935739-1-cuigaosheng1@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pci_disable_device() need be called while module exiting, switch to use
pcim_enable(), pci_disable_device() will be called in pcim_release().
Fixes: ada072816b ("hwmon: (i5500_temp) New driver for the Intel 5500/5520/X58 chipsets")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221112125606.3751430-1-yangyingliang@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The shunt sum critical limit register value should be left shifted
by one bit as its LSB-0 is a reserved bit.
Fixes: 2057bdfb71 ("hwmon: (ina3221) Add summation feature support")
Signed-off-by: Ninad Malwade <nmalwade@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20221108044508.23463-1-nmalwade@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The LTC2947 datasheet (Rev. B) calls out in the section "Register
Description: Non-Accumulated Result Registers" (pg. 30) that "To
calculate temperature, multiply the TEMP register value by 0.204°C
and add 5.5°C". Fix to add 5.5C and not 0.55C.
Fixes: 9f90fd652b ("hwmon: Add support for ltc2947")
Signed-off-by: Derek Nguyen <derek.nguyen@collins.com>
Signed-off-by: Brandon Maier <brandon.maier@collins.com>
Link: https://lore.kernel.org/r/20221110192108.20624-1-brandon.maier@collins.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This reverts commit 54cc3dbfc1.
Zev Weiss reports that the reverted patch may cause a regulator
undercount. Here is his report:
... having regulator-dummy set as a supply on my PMBus regulators
(instead of having them as their own top-level regulators without
an upstream supply) leads to enable-count underflow errors when
disabling them:
# echo 0 > /sys/bus/platform/devices/efuse01/state
[ 906.094477] regulator-dummy: Underflow of regulator enable count
[ 906.100563] Failed to disable vout: -EINVAL
[ 136.992676] reg-userspace-consumer efuse01: Failed to configure state: -22
Zev reports that reverting the patch fixes the problem. So let's do that
for now.
Fixes: 54cc3dbfc1 ("hwmon: (pmbus) Add regulator supply into macro")
Cc: Marcello Sylvester Bauer <sylv@sylv.io>
Reported-by: Zev Weiss <zev@bewilderbeest.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Available sensors are enumerated and reported by the SCMI platform server
using a 16bit identification number; not all such sensors are of a type
supported by hwmon subsystem and, among the supported ones, only a subset
could be temperature sensors that have to be registered with the Thermal
Framework.
Potential clashes between hwmon channels indexes and the underlying real
sensors IDs do not play well with the hwmon<-->thermal bridge automatic
registration routines and could need a sensible number of fake dummy
sensors to be made up in order to keep indexes and IDs in sync.
Avoid to use the hwmon<-->thermal bridge dropping the HWMON_C_REGISTER_TZ
attribute and instead explicit register temperature sensors directly with
the Thermal Framework.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20221031114018.59048-1-cristian.marussi@arm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Intel perf LBR
- A CFI fix to ftrace along with a simplification
- Adjust handling of zero capacity bit mask for resctrl cache allocation
on AMD
- A fix to the AMD microcode loader to attempt patch application on
every logical thread
- A couple of topology fixes to handle CPUID leaf 0x1f enumeration info
properly
- Drop a -mabi=ms compiler option check as both compilers support it now
anyway
- A couple of fixes to how the initial, statically allocated FPU buffer
state is setup and its interaction with dynamic states at runtime
-----BEGIN PGP SIGNATURE-----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=2hxy
-----END PGP SIGNATURE-----
Merge tag 'x86_urgent_for_v6.0_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
"As usually the case, right after a major release, the tip urgent
branches accumulate a couple more fixes than normal. And here is the
x86, a bit bigger, urgent pile.
- Use the correct CPU capability clearing function on the error path
in Intel perf LBR
- A CFI fix to ftrace along with a simplification
- Adjust handling of zero capacity bit mask for resctrl cache
allocation on AMD
- A fix to the AMD microcode loader to attempt patch application on
every logical thread
- A couple of topology fixes to handle CPUID leaf 0x1f enumeration
info properly
- Drop a -mabi=ms compiler option check as both compilers support it
now anyway
- A couple of fixes to how the initial, statically allocated FPU
buffer state is setup and its interaction with dynamic states at
runtime"
* tag 'x86_urgent_for_v6.0_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu: Fix copy_xstate_to_uabi() to copy init states correctly
perf/x86/intel/lbr: Use setup_clear_cpu_cap() instead of clear_cpu_cap()
ftrace,kcfi: Separate ftrace_stub() and ftrace_stub_graph()
x86/ftrace: Remove ftrace_epilogue()
x86/resctrl: Fix min_cbm_bits for AMD
x86/microcode/AMD: Apply the patch early on every logical thread
x86/topology: Fix duplicated core ID within a package
x86/topology: Fix multiple packages shown on a single-package system
hwmon/coretemp: Handle large core ID value
x86/Kconfig: Drop check for -mabi=ms for CONFIG_EFI_STUB
x86/fpu: Exclude dynamic states from init_fpstate
x86/fpu: Fix the init_fpstate size check with the actual size
x86/fpu: Configure init_fpstate attributes orderly
The coretemp driver supports up to a hard-coded limit of 128 cores.
Today, the driver can not support a core with an ID above that limit.
Yet, the encoding of core ID's is arbitrary (BIOS APIC-ID) and so they
may be sparse and they may be large.
Update the driver to map arbitrary core ID numbers into appropriate
array indexes so that 128 cores can be supported, no matter the encoding
of core ID's.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Len Brown <len.brown@intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20221014090147.1836-3-rui.zhang@intel.com
When pwm1_enable is changed from 1 to 0 while pwm1 == 0, the regulator
is not switched off as expected. The reason is that when the fan is
already off, ctx->enabled is false, so pwm_fan_power_off() will be a
no-op.
Handle this case explicitly in pwm_fan_update_enable() by calling
pwm_fan_switch_power() directly.
Fixes: b99152d4f0 ("hwmon: (pwm-fan) Switch regulator dynamically")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20221013135951.4902-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix spelling mistake (Corsaur -> Corsair).
Fixes: 0cf46a653b ("hwmon: (corsair-psu) add USB id of new revision of the HX1000i psu")
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/Yzql13NOvQLlrye1@monster.localdomain
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Here is the large set of char/misc and other small driver subsystem
changes for 6.1-rc1. Loads of different things in here:
- IIO driver updates, additions, and changes. Probably the largest
part of the diffstat
- habanalabs driver update with support for new hardware and features,
the second largest part of the diff.
- fpga subsystem driver updates and additions
- mhi subsystem updates
- Coresight driver updates
- gnss subsystem updates
- extcon driver updates
- icc subsystem updates
- fsi subsystem updates
- nvmem subsystem and driver updates
- misc driver updates
- speakup driver additions for new features
- lots of tiny driver updates and cleanups
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY0GQmA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylyVQCeNJjZ3hy+Wz8WkPSY+NkehuIhyCIAnjXMOJP8
5G/JQ+rpcclr7VOXlS66
=zVkU
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the large set of char/misc and other small driver subsystem
changes for 6.1-rc1. Loads of different things in here:
- IIO driver updates, additions, and changes. Probably the largest
part of the diffstat
- habanalabs driver update with support for new hardware and
features, the second largest part of the diff.
- fpga subsystem driver updates and additions
- mhi subsystem updates
- Coresight driver updates
- gnss subsystem updates
- extcon driver updates
- icc subsystem updates
- fsi subsystem updates
- nvmem subsystem and driver updates
- misc driver updates
- speakup driver additions for new features
- lots of tiny driver updates and cleanups
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'char-misc-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (411 commits)
w1: Split memcpy() of struct cn_msg flexible array
spmi: pmic-arb: increase SPMI transaction timeout delay
spmi: pmic-arb: block access for invalid PMIC arbiter v5 SPMI writes
spmi: pmic-arb: correct duplicate APID to PPID mapping logic
spmi: pmic-arb: add support to dispatch interrupt based on IRQ status
spmi: pmic-arb: check apid against limits before calling irq handler
spmi: pmic-arb: do not ack and clear peripheral interrupts in cleanup_irq
spmi: pmic-arb: handle spurious interrupt
spmi: pmic-arb: add a print in cleanup_irq
drivers: spmi: Directly use ida_alloc()/free()
MAINTAINERS: add TI ECAP driver info
counter: ti-ecap-capture: capture driver support for ECAP
Documentation: ABI: sysfs-bus-counter: add frequency & num_overflows items
dt-bindings: counter: add ti,am62-ecap-capture.yaml
counter: Introduce the COUNTER_COMP_ARRAY component type
counter: Consolidate Counter extension sysfs attribute creation
counter: Introduce the Count capture component
counter: 104-quad-8: Add Signal polarity component
counter: Introduce the Signal polarity component
counter: interrupt-cnt: Implement watch_validate callback
...
* New drivers
- Driver for MAX31760 fan speed controller
- Driver for TEXAS TPS546D24 Buck Converter
- Driver for EMC2301/2/3/5 RPM-based PWM Fan Speed Controller
* Removed drivers
- Drop obsolete asus_wmi_ec_sensors driver
* Cleanups, affecting various drivers
- Use DEFINE_SIMPLE_DEV_PM_OPS where appropriate
- Remove forward declarations
- Move from strlcpy with unused retval to strscpy
- Make use of devm_clk_get_enabled()
- Drop devm_of_pwm_get()
* Other notable cleanup and improvements
- Support for additional USB devide ID and support for reporting
of rail mode via debugfs added to corsair-psu driver
- Support for aditional USB ID in nzxt-smart2 driver
- Support for Aquacomputer High Flow Next in aquacomputer_d5next driver
- Major cleanup of pwm-fan driver
- Major cleanup of mr75203 driver, and added support for new device revision
* Various other minor fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=8u0w
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New drivers:
- Driver for MAX31760 fan speed controller
- Driver for TEXAS TPS546D24 Buck Converter
- Driver for EMC2301/2/3/5 RPM-based PWM Fan Speed Controller
Removed drivers:
- Drop obsolete asus_wmi_ec_sensors driver
Cleanups, affecting various drivers:
- Use DEFINE_SIMPLE_DEV_PM_OPS where appropriate
- Remove forward declarations
- Move from strlcpy with unused retval to strscpy
- Make use of devm_clk_get_enabled()
- Drop devm_of_pwm_get()
Other notable cleanup and improvements:
- Support for additional USB devide ID and support for reporting of
rail mode via debugfs added to corsair-psu driver
- Support for aditional USB ID in nzxt-smart2 driver
- Support for Aquacomputer High Flow Next in aquacomputer_d5next
driver
- Major cleanup of pwm-fan driver
- Major cleanup of mr75203 driver, and added support for new device
revision
And various other minor fixes and cleanups"
* tag 'hwmon-for-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (86 commits)
hwmon: (corsair-psu) add USB id of new revision of the HX1000i psu
hwmon: (pmbus/mp2888) Fix sensors readouts for MPS Multi-phase mp2888 controller
dt-bindings: hwmon: sensirion,shtc1: Clean up spelling mistakes and grammar
hwmon: (nct6683) remove unused variable in nct6683_create_attr_group
hwmon: w83627hf: Reorder symbols to get rid of a few forward declarations
hwmon: (ina3221) Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr()
hwmon: (w83627ehf) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (tmp108) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (tmp103) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (tmp102) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (pwm-fan) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (nct6775) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (max6639) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (max31730) witch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (max31722) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (ltc2947) Switch to EXPORT_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (lm90) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (it87) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (gpio-fan) Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
hwmon: (adt7x10) Switch to EXPORT_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
...
fixes all over the tree. Other subsystems depending on this change
have been asked to pull an immutable topic branch for this.
* new driver for Microchip PCI1xxxx switch
* heavy refactoring of the Mellanox BlueField driver
* we prefer async probe in the i801 driver now
* the rest is usual driver updates (support for more SoCs, some
refactoring, some feature additions)
-----BEGIN PGP SIGNATURE-----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=arni
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- 'remove' callback converted to return void. Big change with trivial
fixes all over the tree. Other subsystems depending on this change
have been asked to pull an immutable topic branch for this.
- new driver for Microchip PCI1xxxx switch
- heavy refactoring of the Mellanox BlueField driver
- we prefer async probe in the i801 driver now
- the rest is usual driver updates (support for more SoCs, some
refactoring, some feature additions)
* tag 'i2c-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (37 commits)
i2c: pci1xxxx: prevent signed integer overflow
i2c: acpi: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
i2c: i801: Prefer async probe
i2c: designware-pci: Use standard pattern for memory allocation
i2c: designware-pci: Group AMD NAVI quirk parts together
i2c: microchip: pci1xxxx: Add driver for I2C host controller in multifunction endpoint of pci1xxxx switch
docs: i2c: slave-interface: return errno when handle I2C_SLAVE_WRITE_REQUESTED
i2c: mlxbf: remove device tree support
i2c: mlxbf: support BlueField-3 SoC
i2c: cadence: Add standard bus recovery support
i2c: mlxbf: add multi slave functionality
i2c: mlxbf: support lock mechanism
macintosh/ams: Adapt declaration of ams_i2c_remove() to earlier change
i2c: riic: Use devm_platform_ioremap_resource()
i2c: mlxbf: remove IRQF_ONESHOT
dt-bindings: i2c: rockchip: add rockchip,rk3128-i2c
dt-bindings: i2c: renesas,rcar-i2c: Add r8a779g0 support
i2c: tegra: Add GPCDMA support
i2c: scmi: Convert to be a platform driver
i2c: rk3x: Add rv1126 support
...
- Rework the device tree initialization, convert the drivers to the
new API and remove the old OF code (Daniel Lezcano).
- Fix return value to -ENODEV when searching for a specific thermal
zone which does not exist (Daniel Lezcano).
- Fix the return value inspection in of_thermal_zone_find() (Dan
Carpenter).
- Fix kernel panic when KASAN is enabled as it detects use after
free when unregistering a thermal zone (Daniel Lezcano).
- Move the set_trip ops inside the therma sysfs code (Daniel Lezcano).
- Remove unnecessary error message as it is already shown in the
underlying function (Jiapeng Chong).
- Rework the monitoring path and move the locks upper in the call
stack to fix some potentials race windows (Daniel Lezcano).
- Fix lockdep_assert() warning introduced by the lock rework (Daniel
Lezcano).
- Do not lock thermal zone mutex in the user space governor (Rafael
Wysocki).
- Revert the Mellanox 'hotter thermal zone' feature because it is
already handled in the thermal framework core code (Daniel Lezcano).
- Increase maximum number of trip points in the thermal core (Sumeet
Pawnikar).
- Replace strlcpy() with unused retval with strscpy() in the core
thermal control code (Wolfram Sang).
- Use module_pci_driver() macro in the int340x processor_thermal
driver (Shang XiaoJing).
- Use get_cpu() instead of smp_processor_id() in the intel_powerclamp
thermal driver to prevent it from crashing and remove unused
accounting for IRQ wakes from it (Srinivas Pandruvada).
- Consolidate priv->data_vault checks in int340x_thermal (Rafael
Wysocki).
- Check the policy first in cpufreq_cooling_register() (Xuewen Yan).
- Drop redundant error message from da9062-thermal (zhaoxiao).
- Drop of_match_ptr() from thermal_mmio (Jean Delvare).
-----BEGIN PGP SIGNATURE-----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=Ufw7
-----END PGP SIGNATURE-----
Merge tag 'thermal-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"The most significant part of this update is the thermal control DT
initialization rework from Daniel Lezcano and the following conversion
of drivers to use the new API introduced by it
Apart from that, the maximum number of trip points in a thermal zone
is increased and there are some fixes and code cleanups
Specifics:
- Rework the device tree initialization, convert the drivers to the
new API and remove the old OF code (Daniel Lezcano)
- Fix return value to -ENODEV when searching for a specific thermal
zone which does not exist (Daniel Lezcano)
- Fix the return value inspection in of_thermal_zone_find() (Dan
Carpenter)
- Fix kernel panic when KASAN is enabled as it detects use after free
when unregistering a thermal zone (Daniel Lezcano)
- Move the set_trip ops inside the therma sysfs code (Daniel Lezcano)
- Remove unnecessary error message as it is already shown in the
underlying function (Jiapeng Chong)
- Rework the monitoring path and move the locks upper in the call
stack to fix some potentials race windows (Daniel Lezcano)
- Fix lockdep_assert() warning introduced by the lock rework (Daniel
Lezcano)
- Do not lock thermal zone mutex in the user space governor (Rafael
Wysocki)
- Revert the Mellanox 'hotter thermal zone' feature because it is
already handled in the thermal framework core code (Daniel Lezcano)
- Increase maximum number of trip points in the thermal core (Sumeet
Pawnikar)
- Replace strlcpy() with unused retval with strscpy() in the core
thermal control code (Wolfram Sang)
- Use module_pci_driver() macro in the int340x processor_thermal
driver (Shang XiaoJing)
- Use get_cpu() instead of smp_processor_id() in the intel_powerclamp
thermal driver to prevent it from crashing and remove unused
accounting for IRQ wakes from it (Srinivas Pandruvada)
- Consolidate priv->data_vault checks in int340x_thermal (Rafael
Wysocki)
- Check the policy first in cpufreq_cooling_register() (Xuewen Yan)
- Drop redundant error message from da9062-thermal (zhaoxiao)
- Drop of_match_ptr() from thermal_mmio (Jean Delvare)"
* tag 'thermal-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (55 commits)
thermal: core: Increase maximum number of trip points
thermal: int340x: processor_thermal: Use module_pci_driver() macro
thermal: intel_powerclamp: Remove accounting for IRQ wakes
thermal: intel_powerclamp: Use get_cpu() instead of smp_processor_id() to avoid crash
thermal: int340x_thermal: Consolidate priv->data_vault checks
thermal: cpufreq_cooling: Check the policy first in cpufreq_cooling_register()
thermal: Drop duplicate words from comments
thermal: move from strlcpy() with unused retval to strscpy()
thermal: da9062-thermal: Drop redundant error message
thermal/drivers/thermal_mmio: Drop of_match_ptr()
thermal: gov_user_space: Do not lock thermal zone mutex
Revert "mlxsw: core: Add the hottest thermal zone detection"
thermal/core: Fix lockdep_assert() warning
thermal/core: Move the mutex inside the thermal_zone_device_update() function
thermal/core: Move the thermal zone lock out of the governors
thermal/governors: Group the thermal zone lock inside the throttle function
thermal/core: Rework the monitoring a bit
thermal/core: Rearm the monitoring only one time
thermal/drivers/qcom/spmi-adc-tm5: Remove unnecessary print function dev_err()
thermal/of: Remove old OF code
...
When enable 'unused-but-set-variable' compile
warning option, it would raise warning as below:
drivers/hwmon/nct6683.c:415:9:
warning: variable 'j' set but not used [-Wunused-but-set-variable]
Variable 'j' in nct6683_create_attr_group is unused,
so remove it and simplify the 'for' loop.
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Link: https://lore.kernel.org/r/20220927114352.2498079-1-zengheng4@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Merge changes regarding the management of ACPI device objects for
6.1-rc1:
- Rename ACPI device object reference counting functions (Rafael
Wysocki).
- Rearrange ACPI device object initialization code (Rafael Wysocki).
- Drop parent field from struct acpi_device (Rafael Wysocki).
- Extend the the int3472-tps68470 driver to support multiple consumers
of a single TPS68470 along with the requisite framework-level
support (Daniel Scally).
* acpi-dev:
platform/x86: int3472: Add board data for Surface Go2 IR camera
platform/x86: int3472: Support multiple gpio lookups in board data
platform/x86: int3472: Support multiple clock consumers
ACPI: bus: Add iterator for dependent devices
ACPI: scan: Add acpi_dev_get_next_consumer_dev()
ACPI: property: Use acpi_dev_parent()
ACPI: Drop redundant acpi_dev_parent() header
ACPI: PM: Fix NULL argument handling in acpi_device_get/set_power()
ACPI: Drop parent field from struct acpi_device
ACPI: scan: Eliminate __acpi_device_add()
ACPI: scan: Rearrange initialization of ACPI device objects
ACPI: scan: Rename acpi_bus_get_parent() and rearrange it
ACPI: Rename acpi_bus_get/put_acpi_device()
* Fix a OCC hwmon userspace compatibility regression that was
introduced in v5.19
* Device tree bindings for the OCC
* A bunch of janitor type fixes
-----BEGIN PGP SIGNATURE-----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=ZFpc
-----END PGP SIGNATURE-----
Merge tag 'fsi-for-v6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/fsi into char-misc-next
Joel writes:
"FSI changes for v6.1
* Fix a OCC hwmon userspace compatibility regression that was
introduced in v5.19
* Device tree bindings for the OCC
* A bunch of janitor type fixes"
* tag 'fsi-for-v6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/fsi:
fsi: core: Check error number after calling ida_simple_get
hwmon: (occ) Check for device property for setting OCC active during probe
fsi: occ: Support probing the hwmon child device from dts node
dt-bindings: hwmon: Add IBM OCC bindings
fsi: master-ast-cf: Fix missing of_node_put in fsi_master_acf_probe
fsi: sbefifo: Add detailed debugging information
fsi: cleanup extern usage in function definition
fsi: occ: Prevent use after free
hwmon (occ): Retry for checksum failure
fsi: occ: Fix checksum failure mode
fsi: Fix typo in comment
Add a specific MFD_SY7636A config option.
As part of this change we can use MFD_SY7636A as a dependency for all
SY7636a components and also remove the name from MFD_SIMPLE_MFD_I2C as
it no longer needs to be selectable.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20220525115554.430971-2-alistair@alistair23.me
A previous commit changed the existing behavior of the driver to skip
attempting to communicate with the OCC during probe. Return to the
previous default behavior of automatically communicating with the OCC
and make it optional with a new device-tree property.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220809200701.218059-4-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Due to the OCC communication design with a shared SRAM area,
checkum errors are expected due to corrupted buffer from OCC
communications with other system components. Therefore, retry
the command twice in the event of a checksum failure.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220426154956.27205-3-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Declarations for static symbols are useless code repetition (unless
there are cyclic dependencies).
Reorder some functions and variables which allows to get rid of 7
forward declarations.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220926153946.1478260-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These new macros allow the compiler to see all the functions even if
!CONFIG_PM* and remove the structures and functions if unused.
This removes the need for __maybe_unused markings.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Ninad Malwade <nmalwade@nvidia.com>
Link: https://lore.kernel.org/r/20220925172759.3573439-19-jic23@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These newer PM macros allow the compiler to see what code it can remove
if !CONFIG_PM_SLEEP. This allows the removal of __maybe_unused markings
whilst achieving the same result.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220925172759.3573439-18-jic23@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These newer PM macros allow the compiler to see what code it can remove
if !CONFIG_PM_SLEEP. This allows the removal of __maybe_unused markings
whilst achieving the same result.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220925172759.3573439-17-jic23@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These newer PM macros allow the compiler to see what code it can remove
if !CONFIG_PM_SLEEP. This allows the removal of __maybe_unused markings
whilst achieving the same result.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220925172759.3573439-16-jic23@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These newer PM macros allow the compiler to see what code it can remove
if !CONFIG_PM_SLEEP. This allows the removal of #ifdef guards whilst
achieving the same result.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220925172759.3573439-15-jic23@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These newer PM macros allow the compiler to see what code it can remove
if !CONFIG_PM_SLEEP. This allows the removal of #ifdef guards whilst
achieving the same result.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220925172759.3573439-14-jic23@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These newer PM macros allow the compiler to see what code it can remove
if !CONFIG_PM_SLEEP. This allows the removal of __maybe_unused markings
whilst achieving the same result.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Zoltán Kővágó <dirty.ice.hu@gmail.com>
Link: https://lore.kernel.org/r/20220925172759.3573439-13-jic23@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These newer PM macros allow the compiler to see what code it can remove
if !CONFIG_PM_SLEEP. This allows the removal of #ifdef guards whilst
achieving the same result.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Roland Stigge <stigge@antcom.de>
Link: https://lore.kernel.org/r/20220925172759.3573439-12-jic23@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These newer PM macros allow the compiler to see what code it can remove
if !CONFIG_PM_SLEEP. This allows the removal of __maybe_unused markings
whilst achieving the same result.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220925172759.3573439-11-jic23@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These newer PM macros allow the compiler to see what code it can remove
if !CONFIG_PM_SLEEP. This allows the removal of __maybe_unused markings
whilst achieving the same result.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220925172759.3573439-10-jic23@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These newer PM macros allow the compiler to see what code it can remove
if !CONFIG_PM_SLEEP. This allows the removal of __maybe_unused markings
whilst achieving the same result. In this case it also lets the
structure itself be removed.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220925172759.3573439-9-jic23@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These newer PM macros allow the compiler to see what code it can remove
if !CONFIG_PM_SLEEP. This allows the removal of __maybe_unused markings
whilst achieving the same result.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220925172759.3573439-8-jic23@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These newer PM macros allow the compiler to see what code it can remove
if !CONFIG_PM_SLEEP. This allows the removal of __maybe_unused markings
whilst achieving the same result.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220925172759.3573439-7-jic23@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These newer PM macros allow the compiler to see what code it can remove
if !CONFIG_PM_SLEEP. This allows the removal of messy #ifdef barriers whilst
achieving the same result.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220925172759.3573439-6-jic23@kernel.org
[groeck: Drop #ifdef from struct gpio_fan_data]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These newer PM macros allow the compiler to see what code it can remove
if !CONFIG_PM_SLEEP. This allows the removal of messy #ifdef barriers whilst
achieving the same result.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20220925172759.3573439-5-jic23@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These newer PM macros allow the compiler to see what code it can remove
if !CONFIG_PM_SLEEP. This allows the removal of messy #ifdef barriers whilst
achieving the same result.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20220925172759.3573439-4-jic23@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These newer PM macros allow the compiler to see what code it can remove
if !CONFIG_PM_SLEEP. This allows the removal of messy #ifdef barriers whilst
achieving the same result.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220925172759.3573439-3-jic23@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These newer PM macros allow the compiler to see what code it can remove
if !CONFIG_PM_SLEEP. This allows the removal of messy #ifdef barriers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220925172759.3573439-2-jic23@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Declarations for static symbols are useless code repetition (unless
there are cyclic dependencies).
Reorder some functions and variables which allows to get rid of 42
forward declarations.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Declarations for static symbols are useless repetition unless there are
cyclic dependencies.
Reorder the functions and variables to get rid of 4 forward declarations.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220924135738.234051-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make use of the cpp symbol DRIVER_NAME to set the driver's name and use
it instead of all explicit usages of the same string. Also make use of
it instead of sis5595_driver.driver.name which breaks a cyclic dependency
between sis5595_probe() and sis5595_driver that in the next commit allows
to drop some forward declarations. For an amd64 allyesconfig this even
reduces the size of the driver by 3 bytes.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220924135738.234051-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In
adm9240_read()
adm9240_fan_read()
adm9240_write_fan_div(),
it assumes that the caller of adm9240_write_fan_div() must hold
data->update_lock. Otherwise, it may cause data races when data is
updated by other threads.
Signed-off-by: Li Zhong <floridsleeves@gmail.com>
Link: https://lore.kernel.org/r/20220924001751.1726369-1-floridsleeves@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On 32-bit platforms, long is 32 bits, so (long)UINT_MAX is less than
(long)SHT4X_MIN_POLL_INTERVAL, which means the clamping operation is
bogus. Fix this by clamping at INT_MAX, so that the upperbound is the
same on all platforms.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Link: https://lore.kernel.org/r/20220924101151.4168414-1-Jason@zx2c4.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Declarations for static symbols are useless repetition unless there are
cyclic dependencies.
Reorder the functions and variables to get rid of 6 forward declarations.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220922074900.2763331-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make use of the cpp symbol DRIVER_NAME to set the driver's name and use
it instead of all explicit usages of the same string. Also make use of
it instead of sis5595_driver.driver.name which breaks a cyclic dependency
between sis5595_probe() and sis5595_driver that in the next commit allows
to drop some forward declarations.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220922074900.2763331-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Several drivers manually register a devm handler to disable their clk.
Convert them to devm_clk_get_enabled().
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Declarations for static symbols are useless repetition unless there are
cyclic dependencies.
Reorder the functions and variables to get rid of 5 forward declarations.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220920135617.1046361-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make use of the cpp symbol DRIVER_NAME to set the driver's name and use
it instead of all explicit usages of the same string. Also make use of
it instead of vt8231_driver.driver.name which breaks a cyclic dependency
between vt8231_probe() and vt8231_driver that in the next commit allows
to drop some forward declarations.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220920135617.1046361-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Declarations for static symbols are useless repetition unless there are
cyclic dependencies.
Reorder the functions and variables to get rid of 6 forward declarations.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220919103155.795151-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make use of the cpp symbol DRIVER_NAME to set the driver's name and also
as name for devm_request_region(). While at it add a module alias using
the new define.
This is a preparation for the next cleanup commit that removes a cyclic
dependency between pc87360_driver (which references pc87360_probe in
.probe) and pc87360_probe() (which used pc87360_driver.driver.name).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220919103155.795151-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This adds the enable attribute which is used to select if zero PWM duty
means to switch off regulator and PWM or to keep them enabled but
at inactive PWM output level.
Depending on the select enable mode, turn off the regulator and PWM if
the PWM duty is zero, or keep them enabled.
This is especially important for fan using inverted PWM signal polarity.
Having regulator supplied and PWM disabled, some PWM controllers provide
the active, rather than inactive signal.
With this change the shutdown as well as suspend/resume paths require
modifcations as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220914153137.613982-6-alexander.stein@ew.tq-group.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Regular calls to set_pwm don't hold the mutex, but the upcoming
update_enable support needs to call set_pwm with the mutex being held.
So provide the previous behavior in set_pwm (handling the lock), while
adding __set_pwm which assumes the lock being held.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220914153137.613982-5-alexander.stein@ew.tq-group.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This handles enabling/disabling the regulator in a single function, while
keeping the enables/disabled balanced. This is a preparation when
regulator is switched from different code paths.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220914153137.613982-4-alexander.stein@ew.tq-group.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Instead of comparing the current to the new pwm duty to decide whether to
enable the PWM, use a dedicated flag. Also apply the new PWM duty in any
case. This is a preparation to enable/disable the regulator dynamically.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220914153137.613982-3-alexander.stein@ew.tq-group.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In preparation for dynamically switching regulator, split the power on
and power off sequence into separate functions.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220914153137.613982-2-alexander.stein@ew.tq-group.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the pmbus driver for TEXAS tps546d24 Buck Converter.
The vout mode of tps546d24 supported relative data format,
which is not supported by the PMBus core.
Signed-off-by: Duke Du <dukedu83@gmail.com>
Link: https://lore.kernel.org/r/1662951668-9849-1-git-send-email-Duke.Du@quantatw.com
[groeck: Add __maybe_unused to tps546d24_of_match declaration]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX31760 is a precision fan speed controller with nonvolatile lookup table.
Device has one internal and one external temperature sensor support.
Controls two fans and measures their speeds. Generates hardware alerts when
programmable max and critical temperatures are exceeded.
Signed-off-by: Ibrahim Tilki <Ibrahim.Tilki@analog.com>
Reviewed-by: Nurettin Bolucu <Nurettin.Bolucu@analog.com>
Link: https://lore.kernel.org/r/20220910171945.48088-2-Ibrahim.Tilki@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix: "ERROR: space required before the open parenthesis '('"
All of the errors were introduced before this series of patches.
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908152449.35457-22-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This change adds debugfs to read and write temperature sensor coefficients
- g, h, j and cal5.
The coefficients can vary between product and product, so it can be very
useful to be able to modify them on the fly during the calibration
process.
e.g.:
cat /sys/kernel/debug/940f23d0000.pvt/ts_coeff_cal5
4096
echo 83000 > sys/kernel/debug/940f23d0000.pvt/ts_coeff_g
Signed-off-by: Eliav Farber <farbere@amazon.com>
Link: https://lore.kernel.org/r/20220908152449.35457-21-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use thermal coefficients from the device tree if they exist.
Otherwise, use default values according to the series (5 or 6).
All coefficients can be used or only part of them.
The coefficients shall be used for fine tuning the default values since
coefficients can vary between product and product.
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908152449.35457-20-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The current equation used in code is aligned to series 5:
T = G + H * (n / cal5 - 0.5) + J * F
Where:
G = 60, H = 200, cal5 = 4094, J = -0.1, F = frequency clock in MHz
Series 6 has a slightly different equation:
T = G + H * (n / cal5 - 0.5)
and a different set of coefficients:
G = 57.4, H = 249.4, cal5 = 4096
This change supports equation and coefficients for both series.
(for series 6, J is set to 0).
The series is determined according to “moortec,ts-series” property in
the device tree.
If absent, series 5 is assumed to be the default.
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908152449.35457-18-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The SENSORS_ASPEED is part of the Aspeed silicon so it makes
sense to depend on ARCH_ASPEED and for compile testing.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20220916120936.372591-1-pbrobinson@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Modify the equation and coefficients used to convert the digital output
to temperature according to series 5 of the Moortec Embedded Temperature
Sensor (METS) datasheet:
T = G + H * (n / cal5 - 0.5) + J * F
Where:
*) G = 60, H = 200, cal5 = 4094, J = -0.1.
*) F = frequency clock in MHz.
*) n is the digital output.
In code, the G, H and J coefficients are multiplied by a factor of 1000
to get the temperature in milli-Celsius.
Final result is clamped in case it exceeds min/max thresholds.
Change is done since it is unclear where the current equation and
coefficients came from.
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908152449.35457-16-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for mr76006 pre-scaler which provides divide-by-2 scaling
of the input voltage, so that it can be presented to the VM for
measurement within its range (the VM input range is limited from -0.1V
to 1V).
The driver reads from the device-tree all the channels that use the
mr76006 pre-scaler and multiplies the voltage result by a factor of 2,
to represent to the user with the actual voltage input source.
Channels that are not in the device-tree are multiplied by a factor
of 1.
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908152449.35457-15-farbere@amazon.com
[groeck: Addressed conflicts against commit d59eacaac9]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add active channel support per voltage monitor.
The number of active channels is read from the device-tree.
When absent in device-tree, all channels are assumed to be used.
This shall be useful to expose sysfs only for inputs that are connected
to a voltage source.
Setting number of active channels to 0, means that entire VM sensor is
not used.
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908152449.35457-13-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Static analyzers report:
drivers/hwmon/emc2305.c:194 emc2305_set_cur_state()
warn: impossible condition '(val > 255) => (0-255 > 255)'
'val' is u8 and thus can never be larger than 255. In theory
the operation calculating 'val' could result in a value larger
than 255, but this won't happen because its parameter has already
been range checked and it is guaranteed that the result never exceeds
255. Remove the unnecessary value check.
Cc: Michael Shych <michaelsh@nvidia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Don't fail the probe function and don't deassert the reset controller if
a "reset" property doesn't exist in the device tree.
Change is done for SOCs that don't support a reset controller.
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908152449.35457-10-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose various hardware
sensors of the Aquacomputer High Flow Next flow sensor, which
communicates through a proprietary USB HID protocol.
The High Flow Next exposes +5V voltages, water quality, conductivity
and flow readings. A temperature sensor can be connected to it, in
which case it provides its reading and an estimation of the
dissipated/absorbed power in the liquid cooling loop.
Additionally, serial number and firmware version are exposed through
debugfs.
Registry offsets were discovered and tested by users on Github [1] [2].
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/issues/8
[2] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/34
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220907100739.806571-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On systems with more than one tps23861, creating the debugfs directory
for additional devices fails with
debugfs: Directory 'tps23861' with parent '/' already present!
To resolve this, include the hwmon device name in the directory name.
Since the name is unique, this guarantees that the debugfs directory
is unique.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220907015405.16547-2-mr.nuke.me@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When reading the 'port_status' debugfs entry, some I2C registers were
read more than once. This looks inefficient in an I2C trace.
To reduce I2C traffic, update tps23861_port_status_show() to only read
each register once. Indexing the port number from 0 instead of 1 also
allows simplifying things a bit.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://lore.kernel.org/r/20220907015405.16547-1-mr.nuke.me@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add driver for Microchip EMC2301/2/3/5 RPM-based PWM Fan Speed Controller.
Modify Makefile and Kconfig to support Microchip EMC2305 RPM-based
PWM Fan Speed Controller.
Signed-off-by: Michael Shych <michaelsh@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20220810171552.56417-3-michaelsh@nvidia.com
[groeck: Drop unnecessary () around DIV_ROUND_CLOSEST()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The MAX31790 has a tach input enable bit in each fan's configuration
register. This is only enabled by the driver if RPM mode is selected,
but the driver doesn't provide a way to independently enable tachometer
input regardless of the regulator mode.
By adding the fanN_enable sysfs files, we can decouple the tach input
from the regulator mode. Also update the documentation.
Signed-off-by: Justin Ledford <justinledford@google.com>
Link: https://lore.kernel.org/r/20220829195930.2521755-1-justinledford@google.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There is no need to call OF specific devm_of_pwm_get() since
the device node parameter duplicates in the device parameter.
Hence we may safely replace it by plain devm_pwm_get() call.
This allows to drop devm_of_pwm_get() as no more users will be.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220826172642.16404-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The devm_clk_get_enabled() helper:
- calls devm_clk_get()
- calls clk_prepare_enable() and registers what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
This simplifies the code, the error handling paths and avoid the need of
a dedicated function used with devm_add_action_or_reset().
Based on my test with allyesconfig, this reduces the .o size from:
text data bss dec hex filename
2419 1472 0 3891 f33 drivers/hwmon/sparx5-temp.o
down to:
2155 1472 0 3627 e2b drivers/hwmon/sparx5-temp.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/cfe4c965074b5ecbe03830b05e038b4594c7b970.1661336689.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When dell-smm-hwmon is loaded on a machine with a buggy BIOS
with the option "force" being enabled, it wrongly prints
that the buggy features where disabled. This may cause
users to wrongly assume that the driver still protects them
from these BIOS bugs even with "force" being enabled.
Replace the messages with two messages each which are depending
on the value of the "force" parameter. The messages which are
being printed when "force" is not set use dev_notice() instead
of dev_warn() since they only serve as a notice.
Tested on a Dell Inspiron 3505.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220822174053.8750-3-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.
Include mod_devicetable.h explicitly to replace the dropped of.h
which included mod_devicetable.h indirectly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220826173700.17395-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add reporting if the PSU is running in single or multi rail mode via
ocpmode debugfs entry. Also update the documentation and driver comments
accordingly.
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/YvS9PZKr0xqFqJny@monster.localdomain
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for reading virtual temperature sensors for the D5 Next, Octo,
Quadro and Farbwerk 360.
Virtual temperature sensors are written to the device by the user, pulling
from an arbitrary value source. Writing to them is not yet reverse
engineered, so the only way to set them for now is to use the official
software.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220817121441.112198-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver utilises a WMI interface found in AMD 500 series ASUS boards,
to read EC registers. But it turned out that ASUS abandoned the
interface, as it disappeared from Intel 600 series boards. Additionally,
the WMI interface was incredibly slow. Therefore this driver was deprecated
in favor of the asus_ec_sensors driver, which supports more boards, more
sensors, and is faster.
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220720072016.102086-2-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In gsc_hwmon_get_devtree_pdata(), we should call of_node_get() before
the of_find_compatible_node() which will automatically call
of_node_put() for the 'from' argument.
Fixes: 3bce5377ef ("hwmon: Add Gateworks System Controller support")
Signed-off-by: Liang He <windhl@126.com>
Co-developed-by: Mengda Chen <chenmengda2009@163.com>
Signed-off-by: Mengda Chen <chenmengda2009@163.com>
Link: https://lore.kernel.org/r/20220916154708.3084515-1-chenmengda2009@163.com
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The offsets for setting speeds of fans connected to Quadro are off by one.
Set them to their correct values.
The offsets as shown point to registers for setting the fan control mode,
which will be explored in future patches, but slipped in here. When
setting fan speeds, the resulting values were overlapping, which made the
fans still run in my initial testing.
Fixes: cdbe34da01 ("hwmon: (aquacomputer_d5next) Add support for Aquacomputer Quadro fan controller")
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220914114327.6941-1-savicaleksa83@gmail.com
Cc: stable@vger.kenrel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Configure ip-polling register to enable polling for all voltage monitor
channels.
This enables reading the voltage values for all inputs other than just
input 0.
Fixes: 9d823351a3 ("hwmon: Add hardware monitoring driver for Moortec MR75203 PVT controller")
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908152449.35457-7-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix voltage allocation and reading to support all channels in all VMs.
Prior to this change allocation and reading were done only for the first
channel in each VM.
This change counts the total number of channels for allocation, and takes
into account the channel offset when reading the sample data register.
Fixes: 9d823351a3 ("hwmon: Add hardware monitoring driver for Moortec MR75203 PVT controller")
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908152449.35457-6-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
According to Moortec Embedded Voltage Monitor (MEVM) series 3 data
sheet, the minimum input signal is -100mv and maximum input signal
is +1000mv.
The equation used to convert the digital word to voltage uses mixed
types (*val signed and n unsigned), and on 64 bit machines also has
different size, since sizeof(u32) = 4 and sizeof(long) = 8.
So when measuring a negative input, n will be small enough, such that
PVT_N_CONST * n < PVT_R_CONST, and the result of
(PVT_N_CONST * n - PVT_R_CONST) will overflow to a very big positive
32 bit number. Then when storing the result in *val it will be the same
value just in 64 bit (instead of it representing a negative number which
will what happen when sizeof(long) = 4).
When -1023 <= (PVT_N_CONST * n - PVT_R_CONST) <= -1
dividing the number by 1024 should result of in 0, but because ">> 10"
is used, and the sign bit is used to fill the vacated bit positions, it
results in -1 (0xf...fffff) which is wrong.
This change fixes the sign problem and supports negative values by
casting n to long and replacing the shift right with div operation.
Fixes: 9d823351a3 ("hwmon: Add hardware monitoring driver for Moortec MR75203 PVT controller")
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908152449.35457-5-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This issue is relevant when "intel,vm-map" is set in device-tree, and
defines a lower number of VMs than actually supported.
This change is needed for all places that use pvt->v_num or vm_num
later on in the code.
Fixes: 9d823351a3 ("hwmon: Add hardware monitoring driver for Moortec MR75203 PVT controller")
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908152449.35457-4-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Bug - in case "intel,vm-map" is missing in device-tree ,'num' is set
to 0, and no voltage channel infos are allocated.
The reason num is set to 0 when "intel,vm-map" is missing is to set the
entire pvt->vm_idx[] with incremental channel numbers, but it didn't
take into consideration that same num is used later in devm_kcalloc().
If "intel,vm-map" does exist there is no need to set the unspecified
channels with incremental numbers, because the unspecified channels
can't be accessed in pvt_read_in() which is the only other place besides
the probe functions that uses pvt->vm_idx[].
This change fixes the bug by moving the incremental channel numbers
setting to be done only if "intel,vm-map" property is defined (starting
loop from 0), and removing 'num = 0'.
Fixes: 9d823351a3 ("hwmon: Add hardware monitoring driver for Moortec MR75203 PVT controller")
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908152449.35457-3-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The tps23861 registers are little-endian, and regmap_read_bulk() does
not do byte order conversion. On BE machines, the bytes were swapped,
and the interpretation of the resistance value was incorrect.
To make it work on both big and little-endian machines, use
le16_to_cpu() to convert the resitance register to host byte order.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Fixes: fff7b8ab22 ("hwmon: add Texas Instruments TPS23861 driver")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220905142806.110598-1-mr.nuke.me@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Because acpi_bus_get_acpi_device() is completely analogous to
acpi_fetch_acpi_dev(), rename it to acpi_get_acpi_dev() and
add a kerneldoc comment to it.
Accordingly, rename acpi_bus_put_acpi_device() to acpi_put_acpi_dev()
and update all of the users of these two functions.
While at it, move the acpi_fetch_acpi_dev() header next to the
acpi_get_acpi_dev() header in the header file holding them.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Punit Agrawal <punit.agrawal@bytedance.com>
The code currently uses a zero margin to mean not cached, but this
results in the cache being bypassed if the (low) margin is set to zero,
leading to lots of unnecessary SMBus transactions in that case. Use a
negative value instead.
Fixes: 07fb76273d ("hwmon: (pmbus) Introduce and use cached vout margins")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220816144414.2358974-1-vincent.whitchurch@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The thermal OF code has a new API allowing to migrate the OF
initialization to a simpler approach. The ops are no longer device
tree specific and are the generic ones provided by the core code.
Convert the ops to the thermal_zone_device_ops format and use the new
API to register the thermal zone with these generic ops.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linexp.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220804224349.1926752-28-daniel.lezcano@linexp.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The thermal OF code has a new API allowing to migrate the OF
initialization to a simpler approach. The ops are no longer device
tree specific and are the generic ones provided by the core code.
Convert the ops to the thermal_zone_device_ops format and use the new
API to register the thermal zone with these generic ops.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linexp.org>
Link: https://lore.kernel.org/r/20220804224349.1926752-27-daniel.lezcano@linexp.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Commit c3963bc0a0 ("hwmon: (nct6775) Split core and platform
driver") introduced a slight change in nct6775_suspend() in order to
avoid an otherwise-needless symbol export for nct6775_update_device(),
replacing a call to that function with a simple dev_get_drvdata()
instead.
As it turns out, there is no guarantee that nct6775_update_device()
is ever called prior to suspend. If this happens, the resume function
ends up writing bad data into the various chip registers, which results
in a crash shortly after resume.
To fix the problem, just add the symbol export and return to using
nct6775_update_device() as was employed previously.
Reported-by: Zoltán Kővágó <dirty.ice.hu@gmail.com>
Tested-by: Zoltán Kővágó <dirty.ice.hu@gmail.com>
Fixes: c3963bc0a0 ("hwmon: (nct6775) Split core and platform driver")
Cc: stable@kernel.org
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20220810052646.13825-1-zev@bewilderbeest.net
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
lm90_detect_nuvoton() is supposed to return NULL if it can not detect
a chip, or a pointer to the chip name if it does. Under some circumstances
it returns an error pointer instead. Some versions of gcc interpret an
ERR_PTR as region of size 0 and generate an error message.
In function ‘__fortify_strlen’,
inlined from ‘strlcpy’ at ./include/linux/fortify-string.h:159:10,
inlined from ‘lm90_detect’ at drivers/hwmon/lm90.c:2550:2:
./include/linux/fortify-string.h:50:33: error:
‘__builtin_strlen’ reading 1 or more bytes from a region of size 0
50 | #define __underlying_strlen __builtin_strlen
| ^
./include/linux/fortify-string.h:141:24: note:
in expansion of macro ‘__underlying_strlen’
141 | return __underlying_strlen(p);
| ^~~~~~~~~~~~~~~~~~~
Returning NULL instead of ERR_PTR() fixes the problem.
Fixes: c7cebce984 ("hwmon: (lm90) Rework detect function")
Reported-by: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Tested-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
- Substantial rewrite of lm90 driver to support several
additional chips and improve support for existing chips.
- Add support of ROG ZENITH II EXTREME, Maximus XI Hero,
Strix Z690-a D4 to asus-ec-sensors driver
- Add support of F71858AD to f71882fg driver
- Add support of Aquacomputer Quadro to aquacomputer_d5next
driver
- Improved assembler code and add support for Dell G5 5590
as well as XPS 13 7390 in dell-smm driver
- Add support for ASUS TUF GAMING B550-PLUS WIFI II to nct775 driver
- Add support for IEEE 754 half precision to PMBus core.
Also support for Analog Devices LT7182S, improve
regulator support, and report various MFR register
values in debugfs.
- Various other minor improvements and fixes
-----BEGIN PGP SIGNATURE-----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=M9iY
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- Substantial rewrite of lm90 driver to support several additional
chips and improve support for existing chips.
- Add support of ROG ZENITH II EXTREME, Maximus XI Hero, and
Strix Z690-a D4 to asus-ec-sensors driver
- Add support of F71858AD to f71882fg driver
- Add support of Aquacomputer Quadro to aquacomputer_d5next driver
- Improved assembler code and add support for Dell G5 5590 as well as
XPS 13 7390 in dell-smm driver
- Add support for ASUS TUF GAMING B550-PLUS WIFI II to nct775 driver
- Add support for IEEE 754 half precision to PMBus core. Also support
for Analog Devices LT7182S, improve regulator support, and report
various MFR register values in debugfs.
- Various other minor improvements and fixes
* tag 'hwmon-for-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (85 commits)
hwmon: (aquacomputer_d5next) Add support for Aquacomputer Quadro fan controller
hwmon: (dell-smm) Improve documentation
hwmon: (nct6775) add ASUS TUF GAMING B550-PLUS WIFI II
hwmon: (occ) Replace open-coded variant of %*phN specifier
hwmon: (sht15) Fix wrong assumptions in device remove callback
hwmon: (aquacomputer_d5next) Add support for reading the +12V voltage sensor on D5 Next
hwmon: (tps23861) fix byte order in current and voltage registers
hwmon: (aspeed-pwm-tacho) increase fan tach period (again)
hwmon: (aquacomputer_d5next) Add D5 Next fan control support
hwmon: (mcp3021) improve driver support for newer hwmon interface
hwmon: (asus-ec-sensors) add definitions for ROG ZENITH II EXTREME
hwmon: (aquacomputer_d5next) Move device-specific data into struct aqc_data
hwmon: (asus-ec-sensors) add missing sensors for X570-I GAMING
hwmon: (drivetemp) Add module alias
hwmon: (asus_wmi_sensors) Save a few bytes of memory
hwmon: (lm90) Use worker for alarm notifications
hwmon: (asus-ec-sensors) add support for Maximus XI Hero
hwmon: (dell-smm) Improve assembly code
hwmon: (pmbus/ltc2978) Set voltage resolution
hwmon: (pmbus) Add list_voltage to pmbus ops
...
- Free the pmem platform device on the registration error path
-----BEGIN PGP SIGNATURE-----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=IY+U
-----END PGP SIGNATURE-----
Merge tag 'x86_misc_for_v6.0_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull misc x86 updates from Borislav Petkov:
- Add a bunch of PCI IDs for new AMD CPUs and use them in k10temp
- Free the pmem platform device on the registration error path
* tag 'x86_misc_for_v6.0_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hwmon: (k10temp): Add support for new family 17h and 19h models
x86/amd_nb: Add AMD PCI IDs for SMN communication
x86/pmem: Fix platform-device leak in error path
Extend aquacomputer_d5next driver to expose hardware temperature sensors
and fans of the Aquacomputer Quadro fan controller, which communicates
through a proprietary USB HID protocol. Implemented by Jack Doan [1].
Four temperature sensors and PWM controllable fans are available. The
liquid flow sensor is also exposed, implemented by Leonard Anderweit [2].
Additionally, serial number, firmware version and power-on count are
exposed through debugfs.
This driver has been tested on x86_64.
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/5
[2] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/9
Originally-from: Jack Doan <me@jackdoan.com>
Originally-from: Leonard Anderweit <leonard.anderweit@gmail.com>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220727100606.9328-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add ASUS TUF GAMING B550-PLUS WIFI II to the WMI monitoring list
to enable support for HW monitoring on that board.
Signed-off-by: Robert Schmidt <r-schmidt@web.de>
Link: https://lore.kernel.org/r/YuBZodZHOnDll5zy@hydra
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
printf()-like functions in the kernel have extensions, such as
%*phN to dump small pieces of memory as hex bytes.
Replace custom approach with the direct use of %*phN.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220726143110.4809-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Taking a lock at the beginning of .remove() doesn't prevent new readers.
With the existing approach it can happen, that a read occurs just when
the lock was taken blocking the reader until the lock is released at the
end of the remove callback which then accessed *data that is already
freed then.
To actually fix this problem the hwmon core needs some adaption. Until
this is implemented take the optimistic approach of assuming that all
readers are gone after hwmon_device_unregister() and
sysfs_remove_group() as most other drivers do. (And once the core
implements that, taking the lock would deadlock.)
So drop the lock, move the reset to after device unregistration to keep
the device in a workable state until it's deregistered. Also add a error
message in case the reset fails and return 0 anyhow. (Returning an error
code, doesn't stop the platform device unregistration and only results
in a little helpful error message before the devm cleanup handlers are
called.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220725194344.150098-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Trying to use this driver on a big-endian machine results in garbage
values for voltage and current. The tps23861 registers are little-
endian, and regmap_read_bulk() does not do byte order conversion. Thus
on BE machines, the most significant bytes got modified, and were
trimmed by the VOLTAGE_CURRENT_MASK.
To resolve this use uint16_t values, and convert them to host byte
order using le16_to_cpu(). This results in correct readings on MIPS.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://lore.kernel.org/r/20220721032255.2850647-1-mr.nuke.me@gmail.com
[groeck: Use __le16 instead of uint16_t]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The old value allows measuring fan speeds down to about 970 RPM and
gives timeout for anything less than that. It is problematic because it
can also be used as an indicator for fan failure or absence.
Despite having read the relevant section of "ASPEED AST2500/AST2520 A2
Datasheet – V1.7" multiple times I wasn't able to figure out what
exactly "fan tach period" and "fan tach falling point of period" mean
(both are set by the driver from the constant this patch is amending).
Experimentation with a Tioga Pass OCP board (AST2500 BMC) showed that
value of 0x0108 gives time outs for speeds below 1500 RPM and the value
offered by the patch is good for at least 750 RPM (the fans can't spin
any slower so the lower bound is unknown). Measuring with the fans
spinning takes about 30 ms, sometimes down to 18 ms, so about the same
as with the previous value.
This constant was last changed with commit 762b1e8880 ("hwmon:
(aspeed-pwm-tacho) increase fan tach period")
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Link: https://lore.kernel.org/r/20220714142344.27071-1-fercerpav@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Define pump and fan speed register offsets in
D5 Next control report, as well as its size, to expose PWM fan control.
Originally-from: Jack Doan <me@jackdoan.com>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220717171412.11142-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the support for CCD offsets used on family 17h models A0h-AFh,
and family 19h models 60h-7Fh.
[ bp: Merge into a single patch. ]
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220719195256.1516-1-mario.limonciello@amd.com
This driver is currently broken, it does not show the in0_input sysfs
file and also returns the following message on startup:
hwmon_device_register() is deprecated. Please convert the driver to
use hwmon_device_register_with_info().
This patch converts the driver and also cleans up the 'read' function.
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Link: https://lore.kernel.org/r/20220712193504.1374656-1-ferlandm@amotus.ca
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As preparation for adding support for more devices in upcoming patches,
move device-specific data, such as number of fans, temperature sensors,
register offsets etc. to struct aqc_data. This is made possible by
the fact that the supported Aquacomputer devices share the same layouts
of sensor substructures. This allows aqc_raw_event() and others to stay
general and not be cluttered with similar loops for each device.
Signed-off-by: Jack Doan <me@jackdoan.com>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220707115050.90021-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding a MODULE_ALIAS() to drivetemp will make the driver easier
for modprobe to autoprobe.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220712214624.1845158-1-linus.walleij@linaro.org
Fixes: 5b46903d8b ("hwmon: Driver for disk and solid state drives with temperature sensors")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The first 'for' loop of asus_wmi_configure_sensor_setup() only computes
the number and type of sensors that exist in the system.
Here, the 'temp_sensor' structure is only used to store the data collected
by asus_wmi_sensor_info(). There is no point in using a devm_ variant for
this allocation. This wastes some memory for no good reason.
Use the stack instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/e23cea6c489fabb109a61e8a33d146a6b74c0529.1656741926.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reporting alarms using hwmon_notify_event() may result in a callback
from the thermal subsystem. This means that such notifications must
not hold the update lock to avoid a deadlock. To avoid this situation,
use a worker to handle notifications.
Reported-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Fixes: f6d0775119 ("hwmon: (lm90) Rework alarm/status handling")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add definitions for ROG MAXIMUS XI HERO and ROG MAXIMUS XI HERO (WI-FI)
boards.
Signed-off-by: Michael Carns <mike@carns.com>
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220627225437.87462-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The new assembly code works on both 32 bit and 64 bit
cpus and allows for more compiler optimisations.
Since clang runs out of registers on 32 bit x86 when
using CC_OUT, we need to execute "setc" ourself.
Also modify the debug message so we can still see
the result (eax) when the carry flag was set.
Tested with 32 bit and 64 bit kernels on a Dell Inspiron 3505.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220220190851.17965-1-W_Armin@gmx.de
[groeck: Rebased to v5.19-rc3]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The LTC2977 regulator does not set the regulator_desc .n_voltages value
which is needed in order to let the regulator core list the regulator
voltage range.
This patch defines a regulator_desc with a voltage range, and uses it
for defining voltage resolution for regulators LTC2972/LTC2974/LTC2975/
LTC2977/LTC2978/LTC2979/LTC2980/LTM2987 based on that they all have a 16
bit ADC with the same stepwise 122.07uV resolution. It also scales the
resolution to a 1mV resolution which is easier to handle.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220614095144.3472305-1-marten.lindahl@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When checking if a regulator supports a voltage range, the regulator
needs to have a list_voltage callback set to the regulator_ops or else
-EINVAL will be returned. This support does not exist for the pmbus
regulators, so this patch adds pmbus_regulator_list_voltage to the
pmbus_regulator_ops.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220614093856.3470672-3-marten.lindahl@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When setting a new voltage the voltage boundaries are read every time to
check that the new voltage is within the proper range. Checking these
voltage boundaries consists of reading one of PMBUS_MFR_VOUT_MIN/
PMBUS_VOUT_MARGIN_LOW registers and then PMBUS_MFR_VOUT_MAX/
PMBUS_VOUT_MARGIN_HIGH together with writing the PMBUS_CLEAR_FAULTS
register.
Since these boundaries are never being changed, it can be cached and
thus saving unnecessary smbus transmissions.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220614093856.3470672-2-marten.lindahl@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In gsc_hwmon_get_devtree_pdata(), of_find_compatible_node() will return
a node pointer with refcount incremented. We should use of_node_put() in
fail path or when it is not used anymore.
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220616114024.3985770-1-windhl@126.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
According to Bug 215983 at bugzilla.kernel.org,
the Dell G5 5590 supports the SMM interface and
can thus be loaded with ignore_dmi being set.
Add the model the DMI table to allow for
automatic loadig on this model.
Compile-tested only.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20220612232208.27901-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A user reported that the program dell-bios-fan-control
worked on his Dell XPS 13 7390 to switch off automatic
fan control.
Since it uses the same mechanism as the dell_smm_hwmon
module, add this model to the fan control whitelist.
Compile-tested only.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20220612041806.11367-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since platform_device_unregister() is NULL-aware, we don't need to duplicate
this check. Remove it and fold the rest of the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20220610103324.87483-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_PMBUS is y and CONFIG_DEBUG_FS is not set.
make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu-, will be failed, like this:
drivers/hwmon/pmbus/pmbus_core.c:593:13: error: ‘pmbus_check_block_register’ defined but not used [-Werror=unused-function]
static bool pmbus_check_block_register(struct i2c_client *client, int page,
^~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[3]: *** [drivers/hwmon/pmbus/pmbus_core.o] Error 1
make[2]: *** [drivers/hwmon/pmbus] Error 2
make[2]: *** Waiting for unfinished jobs....
make[1]: *** [drivers/hwmon] Error 2
make[1]: *** Waiting for unfinished jobs....
make: *** [drivers] Error 2
To fix building warning, use __maybe_unused to attach this func.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: c3ffc3a1ff83("hwmon: (pmbus) add a function to check the presence of a block register")
Signed-off-by: Ren Zhijie <renzhijie2@huawei.com>
Link: https://lore.kernel.org/r/20220609120448.139907-1-renzhijie2@huawei.com
[groeck: Fixed continuation line alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Try to read the channel's temperature offset from device-tree. Having
offset in device-tree node is not mandatory. The offset can only be set
for remote channels.
Signed-off-by: Slawomir Stepien <slawomir.stepien@nokia.com>
Link: https://lore.kernel.org/r/20220607063504.1287855-3-sst@poczta.fm
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ADT7481 have LM90_HAVE_TEMP3 and LM90_HAVE_OFFSET flags, but the
support of second remote channel's offset is missing. Add that
implementation.
Signed-off-by: Slawomir Stepien <slawomir.stepien@nokia.com>
Link: https://lore.kernel.org/r/20220607063504.1287855-2-sst@poczta.fm
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
kvfree(NULL) is safe. NULL check before kvfree() is not needed.
Delete them to simplify the code.
Generated by coccinelle script:
scripts/coccinelle/free/ifnullfree.cocci
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20220606131401.4053036-1-william.xuanziyang@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Try to read the channel's label from device-tree. Having label in
device-tree node is not mandatory.
Signed-off-by: Slawomir Stepien <slawomir.stepien@nokia.com>
Link: https://lore.kernel.org/r/20220525073657.573327-7-sst@poczta.fm
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use this define in all the places where literal '3' was used in this
context.
Signed-off-by: Slawomir Stepien <slawomir.stepien@nokia.com>
Link: https://lore.kernel.org/r/20220525073657.573327-6-sst@poczta.fm
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This will allow binding the driver with the device from the device tree.
Signed-off-by: Slawomir Stepien <slawomir.stepien@nokia.com>
Link: https://lore.kernel.org/r/20220525073657.573327-4-sst@poczta.fm
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The two drivers compile just fine on ARCH=arm. Allow to select
these drivers if COMPILE_TEST is enabled.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Link: https://lore.kernel.org/r/20220527153445.1871086-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add registers to debugfs:
PMBUS_MFR_ID
PMBUS_MFR_MODEL
PMBUS_MFR_REVISION
PMBUS_MFR_LOCATION
PMBUS_MFR_DATE
PMBUS_MFR_SERIAL
To reduce the number of debugfs entries, only values from page 0 are
reported. It is assumed that values of these registers are the same for
all pages. Please note that the PMBUS standard allows added registers to
be page-specific.
Signed-off-by: Adam Wujek <dev_public@wujek.eu>
Link: https://lore.kernel.org/r/20220601013232.801133-2-dev_public@wujek.eu
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Other functions (like pmbus_check_byte_register) cannot be used to check
the presence of a block register, because it will generate error when PEC
is used.
Signed-off-by: Adam Wujek <dev_public@wujek.eu>
Link: https://lore.kernel.org/r/20220601013232.801133-1-dev_public@wujek.eu
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some devices like the Fujitsu Celsius W380 do contain
a working sch56xx hardware monitoring device, but do
not contain the necessary DMI onboard device.
Do not check for the presence of an suitable onboard device
on these machines. The list of affected machines was created
using data collected by the Linux Hardware Project.
Tested on a Fujitsu Esprimo P720, but sadly not on a affected
machine.
Fixes: 393935baa4 (hwmon: (sch56xx-common) Add automatic module loading on supported devices)
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220604220200.2567-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for Analog Devices LT7182S Dual Channel 6A, 20V PolyPhase
Step-Down Silent Switcher with Digital Power System Management.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Several of the chips supported by this driver support configuring the
number of samples (or the fault queue depth) necessary before a fault
or alarm is reported. This is done either with a bit in the configuration
register or with a separate "consecutive alert" register. Support this
functionality with the temp_samples attribute.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add table with device names and known register values for supported
devices from Analog / ON Semiconductor.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NE1618 is similar to NE1617 but supports manufacturer and chip ID
registers as well as 11 bit external temperature resolution.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It was observed that the alert handler may be called from the i2c core
even after alerts have already been disabled. Only disable alerts if
they have not already been disabled.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADT7421 is similar to ADT7461A but supports configurable Beta Compensation.
Packet Error Checking (PEC) is supported but undocumented.
A devicetree node is not added for the added chip since it is quite
unlikely that such an old chip will ever be used in a devicetree based
system. It can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT218 is compatible to NCT72 and NCT214. It also supports PEC (packet
error checking). Similar to NCT72 and NCT214, PEC support is undocumented.
Unlike NCT214 and NCT72, NCT218 does not support the undocumented secondary
chip and manufacturer ID registers at 0x3e and 0x3f and returns 0x00 when
reading those registers. The value for the chip revision register is not
documented but was observed to be 0xca. Use that information to improve
chip detection accuracy.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT214 and NCT72 are compatible to ADT7461/ADT7461A but have full
PEC (packet error checking) support. PEC support is undocumented.
Both chips support the undocumented secondary chip and manufacturer
ID registers at 0x3e and 0x3f, and return 0x61 as chip ID. Use this
information to improve the accuracy of chip detection code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Unlike ADM1023 and compatible chips, NCT210 does not support a temperature
offset register. A real chip was found to have a chip revision of 0x3f.
Use it to detect NCT210 explicitly.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LM86 and LM90 support exactly the same features, so there is no need
to keep their configuration options separate. Combine to reduce data
size.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All chips supported by the ADM1021 driver are also supported by the LM90
driver. Make that support official.
After this change, the adm1021 driver is only needed if the lm90 driver
is disabled. Also, the adm1021 driver misdetects a variety of chips as
MAX1617A, which is unwanted if any of those chips is in the system.
For this reason. make the adm1021 driver dependent on !SENSORS_LM90 to
show that it is not needed if the lm90 driver is enabled, and to avoid
misdetection if a chip supported by the lm90 driver is in the system.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Both chips are quite similar to other chips of this series, so add
support for them to the lm90 driver. Also mention ON Semiconductor NCT210,
which is pin and register compatible to ADM1021A.
None of the chips support the secondary manufacturer and chip ID registers
at 0x3e and 0x3f, but return 0 when reading from those registers.
Use that information to improve the accuracy of chip detection code.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX1617 and LM84 are stripped-down versions of LM90, so they can easily
be supported by the LM90 driver. The most difficult part is chip detection,
since those old chips do not support manufacturer ID or chip ID registers.
The "alarms" attribute is enabled for both chips to match the functionality
of the adm1021 driver. Chip detection was improved and is less prone to
misdetection than the chip detection in the adm1021 driver.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Simplify the code a bit by handling single-register read operations
in lm90_read16(). All we need to do is to skip the low-byte read
operation if the register address is 0.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX6642 is a reduced version of LM90 with no low limits and no conversion
rate register. Its alert functionality is broken, similar to many other
chips supported by the lm90 driver.
After this change, the stand-alone max6642 driver is only needed if the
lm90 driver is disabled. Make it dependent on SENSORS_LM90=n to show that
it is not needed if the lm90 driver is enabled.
A devicetree node is not added for this chip since it is quite unlikely
that such an old chip will ever be used in a devicetree based system.
It can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A flag indicating support for setting the conversion rate doesn't cost
much and will enable us to add support for MAX6642 to the lm90 driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A flag indicating support for minimum temperature limits doesn't cost much
and will enable us to add support for MAX6642 to the lm90 driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX6690 is all but identical to MAX6654. Revision 1 of its
datasheet lists the same chip ID as MAX6654, and a chip labeled
MAX6654 was found to have the chip ID listed as MAX6690 chip ID
in Revision 2 of its datasheet.
A devicetree node is not added for this chip since it is quite unlikely
that such an old chip will ever be used in a devicetree based system.
It can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADT7461A and NCT1008 support the undocumented manufacturer and chip ID
registers at 0x3e and 0x3f, and return 0x61 as chip ID. ADM1032 and
ADT7461 do not support those registers but return 0 when reading them.
Use this information to improve the accuracy of the chip detection code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADT7481, ADT7482, and ADT7483 are similar to ADT7461, but support two
external temperature sensors, similar to MAX6695/6696. They support an
extended temperature range similar to ADT7461. Registers for the second
external channel can be accessed directly or by using the same method as
used by MAX6695/6696. For simplicity, the access method implemented for
MAX6695/6696 is used.
The chips support PEC (packet error checking). Set the PEC feature flag
and let the user decide if it should be enabled or not (it is by default
disabled).
Even though it is only documented for ADT7483, all three chips support a
secondary manufacturer ID register at 0x3e and a chip ID register at 0x3f.
Use the contents of those registers register for improved chip detection
accuracy. Add the same check to the ADT7461A detection code since this chip
also supports the same (undocumented) registers.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Reviewed-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Unlike MAX6646/MAX6647/MAX6649, MAX6648 and MAX6692 only support
a temperature range of 0..127 degrees C. Separate support for the
two sets of chips to be able to support maximum temperature ranges
correctly for all chips. Introduce new feature flag to indicate
temperature support up to 255 degrees C.
Since the chips are almost identical except for the supported temperature
range, automatic chip detection is limited. Effectively this means that
MAX6648 may be mis-detected as MAX6649 when auto-detected, but there is
nothing we can do about that.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We don't want to support the obsolete 'alarms' attribute for new
chips supported by this driver. Add flag to indicate 'alarms' attribute
support and use it for existing chips. This flag will not be set for
additional chips supported by this driver in the future.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When support for G781 was added, chips with ID 0x01 were found at I2C
addresses 0x4c and 0x4d. The G781 datasheet (version 1.3 from October 2003)
says that the device ID for G781-1 is 0x03, not 0x01. Also, the datasheet
states that the chip at I2C address is G781 and the chip at I2C address
0x4d is G781-1.
A G781-1 at I2C address 0x4d was now found to have a chip ID of 0x03
as suggested by the datasheet. Accept both 0x01 and 0x03 chip IDs at both
addresses to ensure that all variants of G781 are detected properly.
While at it, improve chip detection accuracy by reading two additional
registers and ensuring that only expected bits are set in those registers.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The NCT1008 datasheet, Revision 3, states that its chip revision is
0x57. This matches the ADT7461A chip revision, and NCT1008 is therefore
detected as ADT7461A. In revision 6 of the datasheet, the chip revision
register is no longer documented. Multiple samples of NCT1008 were found
to report a chip revision of 0x54. As it turns out, one of the patches
submitted to add NCT1008 support to the lm90 driver already included a
check for chip revision 0x54. Unfortunately, that patch never made it into
the kernel. Remedy the situation and explicitly detect chips with revision
0x54 as NCT1008.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The detect function is getting larger and larger and difficult to
understand or review. Split it into per-manufacturer detect functions
to improve readability.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since temperature conversion functions are now unified, there is no need
to keep "the chip supports a configurable extended temperature range" and
"the chip has extended temperature range enabled" flags separate.
Use a single flag instead to reflect both.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
While most LM90 compatible chips support a temperature sensor resolution
of 11 bit, this is not the case for all chips. ADT7461 only supports a
resolution of 10 bit, and TMP451/TMP461 support a resolution of 12 bit.
Add support for various temperature sensor resolutions. To do this,
model all temperature sensors as 16 bit sensors, and use unified
temperature conversion functions which take the sensor resolution
as parameter.
While enhancing functionality, this has the positive side effect of
reducing code size by about 5%.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When reading 16-bit volatile registers, the code uses a trick to
determine if a temperature is consistent: It reads the high part
of the register twice. If the values are the same, the code assumes
that the reading is consistent. If the value differs, the code
re-reads the second register as well and assumes that it now has
correct values.
This is only necessary for volatile registers. Add a parameter to
lm90_read16() to indicate if the register is volatile to avoid the
extra overhead for non-volatile registers.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADT7461 and TMP451 temperature sensors support extended temperature ranges.
If standard temperature range is selected, the temperature range is
unsigned and limited to 0 .. 127 degrees C. For TMP461, the standard
temperature range is -128000 ... 127000 degrees C. Distinguish between
the two chips by introducing a feature flag indicating if the standard
temperature range is signed or unsigned. Use the same flag for MAX6646/
MAX6647 as well since those chips also support unsigned temperatures.
Note that while the datasheet for ADT7461 suggests that the default
temperature range is unsigned, tests with a real chip suggest that this
is not the case: If the temperature offset is set to a value << 0,
the temperature register does report negative values.
Tests with real chips show that MAX6680/MAX6681 and SA56004 report
temperatures of 128 degrees C and higher as negative temperatures.
Add respective comments to the code.
Also use clamp_val() and DIV_ROUND_CLOSEST where appropriate in
calculations.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Experiments show that ADT7461A and NCT1008 support PEC, even though it is
not documented. Enable support for it in the driver. Since ADT7461 only
supports partial PEC, this means that the configuration for ADT7461A
needs to be separated from ADT7461.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Revision 0 of the ADT7461 datasheet suggests that the chip supports PEC
(packet error checking). This information is gone in later versions of the
datasheet. Experiments show that PEC support on ADT7461 is similar to PEC
support in ADM1032, ie it is only supported for read operations. Add
support for it to the driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
PEC (packet error checking) support for ADM1032 is currently only enabled
if the chip was auto-detected, but not if a chip is instantiated
explicitly. Always enable PEC support by introducing a chip feature flag
indicating partial PEC support. Also, for consistency, disable PEC support
by default to match existing functionality if the chip was not auto-
detected.
At the same time, introduce generic support for PEC with a separate feature
flag. This will be used when support for chips with full PEC functionality
is added.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The register write address either matches the read address, or it is the
read address plus 6. Simplify the code and resolve the write address
programmatically instead of having two defines for each register.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Handling bit shifts necessary to extract status bits during compile time
reduces code and data size by almost 5% when building for x86_64.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reorder chip enumeration in alphabetical order to make it easier to
see which chips are supported, and to clarify where to add support
new chip types. No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reorder include files in alphabetical order to reduce the chance of
duplicates and to make it clear where new include files should be
added. Drop the unnecessary include of linux/sysfs.h. Include
linux/device.h instead because that is what is actually used.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
