Enable survivability mode if supported and configfs attribute is set.
Enabling survivability mode manually is useful in cases where pcode does
not detect failure, validation and for IFR (in-field-repair).
To set configfs survivability mode attribute for a device
echo 1 > /sys/kernel/config/xe/0000:03:00.0/survivability_mode
The card enters survivability mode if supported
v2: add a log if survivability mode is enabled for unsupported
platforms (Rodrigo)
Signed-off-by: Riana Tauro <riana.tauro@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250407051414.1651616-4-riana.tauro@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Commit d40f275d96 ("drm/xe: Move survivability entirely to xe_pci")
moved the survivability handling to be done entirely in the xe_pci
layer. However there are some issues with that approach:
1) Survivability mode needs at least the mmio initialized, otherwise it
can't really read a register to decide if it should enter that state
2) SR-IOV mode should be initialized, otherwise it's not possible to
check if it's VF
Besides, as pointed by Riana the check for
xe_survivability_mode_enable() was wrong in xe_pci_probe() since it's
not a bool return.
Fix that by moving the initialization to be entirely in the xe_device
layer, with the correct dependencies handled: only after mmio and sriov
initialization, and not triggering it on error from
wait_for_lmem_ready(). This restores the trigger behavior before that
commit. The xe_pci layer now only checks for "is it enabled?",
like it's doing in xe_pci_suspend()/xe_pci_remove(), etc.
Cc: Riana Tauro <riana.tauro@intel.com>
Fixes: d40f275d96 ("drm/xe: Move survivability entirely to xe_pci")
Reviewed-by: Riana Tauro <riana.tauro@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250314-fix-survivability-v5-1-fdb3559ea965@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
There's an odd split between xe_pci.c and xe_device.c wrt
xe_survivability: it's initialized by xe_device, but then finalized by
xe_pci. Move it entirely to the outer layer, xe_pci, so it controls
the flow entirely.
This also allows to stop ignoring some of the errors. E.g.: if there's
an -ENOMEM, it shouldn't continue as if it survivability had been
enabled.
One change worth mentioning is that if "wait for lmem" fails, it will
also check the pcode status to decide if it should enter or not in
survivability mode, which it was not doing before. The bit from pcode
for that decision should remain the same after lmem failed
initialization, so it should be fine.
Cc: Riana Tauro <riana.tauro@intel.com>
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Reviewed-by: Riana Tauro <riana.tauro@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250222001051.3012936-9-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Enable boot survivability mode if pcode initialization fails and
if boot status indicates a failure. In this mode, drm card is not
exposed and driver probe returns success after loading the bare minimum
to allow firmware to be flashed via mei.
v2: abstract survivability mode variable
add BMG check inside function (Jani, Rodrigo)
v3: return -EBUSY during system suspend (Anshuman)
check survivability mode in pci probe only
on error
Signed-off-by: Riana Tauro <riana.tauro@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250128095632.1294722-3-riana.tauro@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Boot Survivability is a software based workflow for recovering a system
in a failed boot state. Here system recoverability is concerned with
recovering the firmware responsible for boot.
This is implemented by loading the driver with bare minimum (no drm card)
to allow the firmware to be flashed through mei-gsc and collect telemetry.
The driver's probe flow is modified such that it enters survivability mode
when pcode initialization is incomplete and boot status denotes a failure.
In this mode, drm card is not exposed and presence of survivability_mode
entry in PCI sysfs is used to indicate survivability mode and
provide additional information required for debug
This patch adds initialization functions and exposes admin
readable sysfs entries
The new sysfs will have the below layout
/sys/bus/.../bdf
├── survivability_mode
v2: reorder headers
fix doc
remove survivability info and use mode to display information
use separate function for logging survivability information
for critical error (Rodrigo)
v3: use for loop
use dev logs instead of drm
use helper function for aux history(Rodrigo)
remove unnecessary error check of greater than max_scratch
as we are reading only 3 bit
v4: fix checkpatch warnings
fix space (Rodrigo)
rename register
Signed-off-by: Riana Tauro <riana.tauro@intel.com>
Acked-by: Ashwin Kumar Kulkarni <ashwin.kumar.kulkarni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250128095632.1294722-2-riana.tauro@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
