Tegra TRM documentation states that hardware should be in a default state
when power partition is turned off, i.e. reset should be asserted. This
patch adds the missing reset assertions.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The hardware documentation uses AVDD_IO_HDMI_DP and VDD_HDMI_DP_PLL to
denote the two power supplies that drive the HDMI/DP outputs of the SOR.
Use these names instead of the arbitrary AVDD_IO and VDD_PLL names that
were used previously to avoid confusion.
Signed-off-by: Thierry Reding <treding@nvidia.com>
SW can trigger MIPI pads calibration any time after power on
but calibration results will be latched and applied to the pads
by MIPI CAL unit only when the link is in LP-11 state and then
status register will be updated.
For CSI, trigger of pads calibration happen during CSI stream
enable where CSI receiver is kept ready prior to sensor or CSI
transmitter stream start.
So, pads may not be in LP-11 at this time and waiting for the
calibration to be done immediate after calibration start will
result in timeout.
This patch splits tegra_mipi_calibrate() and tegra_mipi_wait()
so triggering for calibration and waiting for it to complete can
happen at different stages.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra CSI driver need a separate MIPI device for each channel as
calibration of corresponding MIPI pads for each channel should
happen independently.
So, this patch updates tegra_mipi_request() API to add a device_node
pointer argument to allow creating mipi device for specific device
node rather than a device.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Only when vblanks are supported ofc.
Some drivers do this already, but most unfortunately missed it. This
opens up bugs after driver load, before the crtc is enabled for the
first time. syzbot spotted this when loading vkms as a secondary
output. Given how many drivers are buggy it's best to solve this once
and for all in shared helper code.
Aside from moving the few existing calls to drm_crtc_vblank_reset into
helpers (i915 doesn't use helpers, so keeps its own) I think the
regression risk is minimal: atomic helpers already rely on drivers
calling drm_crtc_vblank_on/off correctly in their hooks when they
support vblanks. And driver that's failing to handle vblanks after
this is missing those calls already, and vblanks could only work by
accident when enabling a CRTC for the first time right after boot.
Big thanks to Tetsuo for helping track down what's going wrong here.
There's only a few drivers which already had the necessary call and
needed some updating:
- komeda, atmel and tidss also needed to be changed to call
__drm_atomic_helper_crtc_reset() intead of open coding it
- tegra and msm even had it in the same place already, just code
motion, and malidp already uses __drm_atomic_helper_crtc_reset().
- Laurent noticed that rcar-du and omap open-code their crtc reset and
hence would actually be broken by this patch now. So fix them up by
reusing the helpers, which brings the drm_crtc_vblank_reset() back.
Only call left is in i915, which doesn't use drm_mode_config_reset,
but has its own fastboot infrastructure. So that's the only case where
we actually want this in the driver still.
I've also reviewed all other drivers which set up vblank support with
drm_vblank_init. After the previous patch fixing mxsfb all atomic
drivers do call drm_crtc_vblank_on/off as they should, the remaining
drivers are either legacy kms or legacy dri1 drivers, so not affected
by this change to atomic helpers.
v2: Use the drm_dev_has_vblank() helper.
v3: Laurent pointed out that omap and rcar-du used drm_crtc_vblank_off
instead of drm_crtc_vblank_reset. Adjust them too.
v4: Laurent noticed that rcar-du and omap open-code their crtc reset
and hence would actually be broken by this patch now. So fix them up
by reusing the helpers, which brings the drm_crtc_vblank_reset() back.
v5: also mention rcar-du and ompadrm in the proper commit message
above (Laurent).
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://syzkaller.appspot.com/bug?id=0ba17d70d062b2595e1f061231474800f076c7cb
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: syzbot+0871b14ca2e2fb64f6e3@syzkaller.appspotmail.com
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: "James (Qian) Wang" <james.qian.wang@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mihail Atanassov <mihail.atanassov@arm.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Brian Masney <masneyb@onstation.org>
Cc: Emil Velikov <emil.velikov@collabora.com>
Cc: zhengbin <zhengbin13@huawei.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-tegra@vger.kernel.org
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200612160056.2082681-1-daniel.vetter@ffwll.ch
UAPI Changes:
- Add DRM_MODE_TYPE_USERDEF for video modes specified in cmdline.
Cross-subsystem Changes:
- Assorted devicetree binding updates.
- Add might_sleep() to dma_fence_wait().
- Fix fbdev's get_user_pages_fast() handling, and use pin_user_pages.
- Small cleanup with IS_BUILTIN in video/fbdev drivers.
- Fix video/hdmi coding style for infoframe size.
Core Changes:
- Silence vblank output during init.
- Fix DP-MST corruption during send msg timeout.
- Clear leak in drm_gem_objecs_lookup().
- Make newlines work with force connector attribute.
- Fix module refcounting error in drm_encoder_slave, and use new i2c api.
- Header fix for drm_managed.c
- More struct_mutex removal for !legacy drivers:
- Remove gem_free_object()
- Removal of drm_gem_object_put_unlocked().
- Show current->comm alongside pid in debug printfs.
- Add drm_client_modeset_check() + drm_client_framebuffer_flush().
- Replace drm_fb_swab16 with drm_fb_swap that also supports 32-bits.
- Remove mode->vrefresh, and compactify drm_display_mode.
- Use drm_* macros for logging and warnings.
- Add WARN when drm_gem_get_pages is used on a private obj.
- Handle importing and imported dmabuf better in shmem helpers.
- Small fix for drm/mm hole size comparison, and remove invalid entry optimization.
- Add a drm/mm selftest.
- Set DSI connector type for DSI panels.
- Assorted small fixes and documentation updates.
- Fix DDI I2C device registration for MST ports, and flushing on destroy.
- Fix master_set return type, used by vmwgfx.
- Make the drm_set/drop_master ioctl symmetrical.
Driver Changes:
Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4, i915, omap, fbdev/sm712fb, fbdev/pxafb, console/newport_con, msm, virtio, udl, malidp, hdlcd, bridge/ti-sn65dsi86, panfrost.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4 (multiple), i915.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE TX26D202VM0BWA panel.
- Use GEM CMA functions in arc, arm, atmel-hlcdc, fsi-dcu, hisilicon, imx, ingenic, komeda, malidp, mcde, meson, msxfb, rcar-du, shmobile, stm, sti, tilcdc, tve200, zte.
- Remove gem_print_info.
- Improve gem_create_object_helper so udl can use shmem helpers.
- Convert vc4 dt bindings to schemas, and add clock properties.
- Device initialization cleanups for mgag200.
- Add a workaround to fix DP-MST short pulses handling on broken hardware in i915.
- Allow build test compiling arm drivers.
- Use managed pci functions in mgag200 and ast.
- Use dev_groups in malidp.
- Add per pixel alpha support for PX30 VOP in rockchip.
- Silence deferred probe logs in panfrost.
-----BEGIN PGP SIGNATURE-----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=ZmKI
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-06-19' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.9:
UAPI Changes:
- Add DRM_MODE_TYPE_USERDEF for video modes specified in cmdline.
Cross-subsystem Changes:
- Assorted devicetree binding updates.
- Add might_sleep() to dma_fence_wait().
- Fix fbdev's get_user_pages_fast() handling, and use pin_user_pages.
- Small cleanup with IS_BUILTIN in video/fbdev drivers.
- Fix video/hdmi coding style for infoframe size.
Core Changes:
- Silence vblank output during init.
- Fix DP-MST corruption during send msg timeout.
- Clear leak in drm_gem_objecs_lookup().
- Make newlines work with force connector attribute.
- Fix module refcounting error in drm_encoder_slave, and use new i2c api.
- Header fix for drm_managed.c
- More struct_mutex removal for !legacy drivers:
- Remove gem_free_object()
- Removal of drm_gem_object_put_unlocked().
- Show current->comm alongside pid in debug printfs.
- Add drm_client_modeset_check() + drm_client_framebuffer_flush().
- Replace drm_fb_swab16 with drm_fb_swap that also supports 32-bits.
- Remove mode->vrefresh, and compactify drm_display_mode.
- Use drm_* macros for logging and warnings.
- Add WARN when drm_gem_get_pages is used on a private obj.
- Handle importing and imported dmabuf better in shmem helpers.
- Small fix for drm/mm hole size comparison, and remove invalid entry optimization.
- Add a drm/mm selftest.
- Set DSI connector type for DSI panels.
- Assorted small fixes and documentation updates.
- Fix DDI I2C device registration for MST ports, and flushing on destroy.
- Fix master_set return type, used by vmwgfx.
- Make the drm_set/drop_master ioctl symmetrical.
Driver Changes:
Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4, i915, omap, fbdev/sm712fb, fbdev/pxafb, console/newport_con, msm, virtio, udl, malidp, hdlcd, bridge/ti-sn65dsi86, panfrost.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4 (multiple), i915.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE TX26D202VM0BWA panel.
- Use GEM CMA functions in arc, arm, atmel-hlcdc, fsi-dcu, hisilicon, imx, ingenic, komeda, malidp, mcde, meson, msxfb, rcar-du, shmobile, stm, sti, tilcdc, tve200, zte.
- Remove gem_print_info.
- Improve gem_create_object_helper so udl can use shmem helpers.
- Convert vc4 dt bindings to schemas, and add clock properties.
- Device initialization cleanups for mgag200.
- Add a workaround to fix DP-MST short pulses handling on broken hardware in i915.
- Allow build test compiling arm drivers.
- Use managed pci functions in mgag200 and ast.
- Use dev_groups in malidp.
- Add per pixel alpha support for PX30 VOP in rockchip.
- Silence deferred probe logs in panfrost.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/001cd9a6-405d-4e29-43d8-354f53ae4e8b@linux.intel.com
As of commit 4dc55525b0 ("drm: plane: Verify that no or all planes
have a zpos property") a warning is emitted if there's a mix of planes
with and without a zpos property.
On Tegra, cursor planes are always composited on top of all other
planes, which is why they never had a zpos property attached to them.
However, since the composition order is fixed, this is trivial to
remedy by simply attaching an immutable zpos property to them.
v3: do not hardcode zpos for overlay planes used as cursor (Dmitry)
v2: hardcode cursor plane zpos to 255 instead of 0 (Ville)
Reported-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to remove the dependency on the simple-bus compatible string,
which causes the OF driver core to register all child devices, make the
display-hub driver explicitly register the display controller children.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Though the unconditional enable/disable code is not a final solution,
we don't want to run into a NULL pointer situation when window group
doesn't link to its DC parent if the DC is disabled in Device Tree.
So this patch simply adds a check to make sure that window group has
a valid parent before running into tegra_windowgroup_enable/disable.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Spelling out _unlocked for each and every driver is a annoying.
Especially if we consider how many drivers, do not know (or need to)
about the horror stories involving struct_mutex.
Just drop the suffix. It makes the API cleaner.
Done via the following script:
__from=drm_gem_object_put_unlocked
__to=drm_gem_object_put
for __file in $(git grep --name-only $__from); do
sed -i "s/$__from/$__to/g" $__file;
done
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200515095118.2743122-32-emil.l.velikov@gmail.com
When testing whether or not to enable the use of the SMMU, consult the
supported DMA mask rather than the actually configured DMA mask, since
the latter might already have been restricted.
Fixes: 2d9384ff91 ("drm/tegra: Relax IOMMU usage criteria on old Tegra")
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra DRM drivers includes the legacy GPIO headers
<linux/gpio.h> and <linux/of_gpio.h> but what it really
uses is <linux/gpio/consumer.h> since only gpio_desc
structs are ever referenced.
Include the right header on the top level tegra/drm.h
file and drop all the surplus includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415122427.111769-1-linus.walleij@linaro.org
The tegra driver uses empty implementations for its encoders. Replace
the code with the generic simple encoder.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305155950.2705-16-tzimmermann@suse.de
This contains some minor cleanups, nothing too exciting.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAl5rvgETHHRyZWRpbmdA
bnZpZGlhLmNvbQAKCRDdI6zXfz6zoXwZEACLn1yKbPweqYORmiVU0upNtvFjf9qm
Emn/dtX2pvfKw/9++dDIF5RgMIIDHXBeei5JS+X3v40xOsAK0xrf66aZ4kBGsdpg
cp/eo1g+um2zoohrB7jBvtLa2FqdrRYCs9DY7gotqP5lm+POheOEBs1waS/dTm7B
WydvCxtMLeIL0hNDfuvz0HWrCPlKY9CE/SkSP6RUsgQGFNHL9fHyYw0nJHwb2/Fl
NzLPx17VX0PDi4rGdkZl+FV6lcsGdIgCJ5zAFqVHrH9nnCXWUZVV5w6cA7LNmph4
xwSV9uQfujTeGxRdrroAbqk8psJ41kHlON6uYZO0nidSfbXCoaFkTDQ+zd9cdwU9
EsQEQSapCK5IpnqvXd/oevEV4E1o5cLbCOllFRInmWWQvSF92Ydbzvp+UOPnTBNQ
6kqLUYcBXcBBa3Zv7TQ6KhyrgkO2rzF8iSZ/DczzVzfzvv1qvHnlWD9n9o2a0J1f
30yv8leIwJmzsi7k9A6OdPZo0+u7cu+bTqifBVFGTkTxxtzoj1BwH/zr1SPlQrjM
V953YNymXax9HJtYGCQg5od2kRo9T2kK0s1b0rYtFDmHmy0NPyafSywci0Q/uU8a
DutjKgpW1JS5dHVkmlU0RuKDDwBvONfC8l4UOmiI/o0E6dyAah9dDsVcLbbDm92K
v44TRik/3nrbpw==
=xg7O
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-5.7-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v5.7-rc1
This contains some minor cleanups, nothing too exciting.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313171042.2924890-1-thierry.reding@gmail.com
As a result of commit 987d65d013 (drm: debugfs: make
drm_debugfs_create_files() never fail) and changes to various debugfs
functions in drm/core and across various drivers, there is no need for
the drm_driver.debugfs_init() hook to have a return value. Therefore,
declare it as void.
This also includes refactoring all users of the .debugfs_init() hook to
return void across the subsystem.
v2: include changes to the hook and drivers that use it in one patch to
prevent driver breakage and enable individual successful compilation of
this change.
References: https://lists.freedesktop.org/archives/dri-devel/2020-February/257183.html
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-18-wambui.karugax@gmail.com
Since 987d65d013 (drm: debugfs: make
drm_debugfs_create_files() never fail) there is no need to check the
return value of drm_debugfs_create_files(). Therefore, remove the
return checks and error handling of the drm_debugfs_create_files()
function from various debugfs init functions in drm/tegra and have
them return 0 directly.
v2: remove conversion of tegra_debugfs_init() to void to avoid build
breakage.
References: https://lists.freedesktop.org/archives/dri-devel/2020-February/257183.html
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-2-wambui.karugax@gmail.com
Driver fails to probe with -EPROBE_DEFER, which produces a bit noisy error
message in KMSG during kernel's boot up. This happens because voltage
regulators tend to be probed later than the DRM driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Driver fails to probe with -EPROBE_DEFER if display output isn't ready
yet. This produces a bit noisy error message in KMSG during kernel's boot
up on Tegra20 and Tegra30 because RGB output tends to be probed earlier
than a corresponding voltage regulator driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Runtime PM and RGB output need to be released when host1x client
registration fails. The releasing is missed in the code, let's correct it.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The devm_platform_ioremap_resource() helper replaces few lines of a
boilerplate code with a single line, making code to look cleaner a tad.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
drm_fb_helper_{add,remove}_one_connector() and
drm_fb_helper_single_add_all_connectors() are dummy functions now
and serve no purpose. Hence remove their calls.
This is the preparatory step for removing the
drm_fb_helper_{add,remove}_one_connector() functions from
drm_fb_helper.h
This removal is done using below sementic patch and unused variable
compilation warnings are fixed manually.
@@
@@
- drm_fb_helper_single_add_all_connectors(...);
@@
expression e1;
statement S;
@@
- e1 = drm_fb_helper_single_add_all_connectors(...);
- S
@@
@@
- drm_fb_helper_add_one_connector(...);
@@
@@
- drm_fb_helper_remove_one_connector(...);
Changes since v1:
* Squashed warning fixes into the patch that introduced the
warnings (into 5/7) (Laurent, Emil, Lyude)
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305120434.111091-6-pankaj.laxminarayan.bharadiya@intel.com
The max connector argument for drm_fb_helper_init() isn't used anymore
hence remove it.
All the drm_fb_helper_init() calls are modified with below sementic
patch.
@@
expression E1, E2, E3;
@@
- drm_fb_helper_init(E1,E2, E3)
+ drm_fb_helper_init(E1,E2)
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305120434.111091-2-pankaj.laxminarayan.bharadiya@intel.com
These are a couple of quick fixes for regressions that were found during
the first two weeks of the merge window.
-----BEGIN PGP SIGNATURE-----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=W1SC
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-5.6-rc1-fixes' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Fixes for v5.6-rc1
These are a couple of quick fixes for regressions that were found during
the first two weeks of the merge window.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200206172753.2185390-1-thierry.reding@gmail.com
This partially reverts the DMA API support that was recently merged
because it was causing performance regressions on older Tegra devices.
Unfortunately, the cache maintenance performed by dma_map_sg() and
dma_unmap_sg() causes performance to drop by a factor of 10.
The right solution for this would be to cache mappings for buffers per
consumer device, but that's a bit involved. Instead, we simply revert to
the old behaviour of sharing IOVA mappings when we know that devices can
do so (i.e. they share the same IOMMU domain).
Cc: <stable@vger.kernel.org> # v5.5
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Older Tegra devices only allow addressing 32 bits of memory, so whether
or not the host1x is attached to an IOMMU doesn't matter. host1x IOMMU
attachment is only needed on devices that can address memory beyond the
32-bit boundary and where the host1x doesn't support the wide GATHER
opcode that allows it to access buffers at higher addresses.
Cc: <stable@vger.kernel.org> # v5.5
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Commit fd67e9c6ed ("drm/tegra: Do not implement runtime PM") replaced
the generic runtime PM usage by a host1x bus-specific implementation in
order to work around some assumptions baked into runtime PM that are in
conflict with the requirements in the Tegra DRM driver.
Unfortunately the new runtime PM callbacks are not setup yet at the time
when the SOR driver first needs to resume the device to register the SOR
pad clock, and accesses to register will cause the system to hang.
Note that this only happens on Tegra124 and Tegra210 because those are
the only SoCs where the SOR pad clock is registered from the SOR driver.
Later generations use a SOR pad clock provided by the BPMP.
Fix this by moving the registration of the SOR pad clock after the
host1x client has been registered. That's somewhat suboptimal because
this could potentially, though it's very unlikely, cause the Tegra DRM
to be probed if the SOR happens to be the last subdevice to register,
only to be immediately removed again if the SOR pad output clock fails
to register. That's just a minor annoyance, though, and doesn't justify
implementing a workaround.
Fixes: fd67e9c6ed ("drm/tegra: Do not implement runtime PM")
Signed-off-by: Thierry Reding <treding@nvidia.com>
If the driver fails to probe, make sure to disable runtime PM again.
While at it, make the cleanup code in ->remove() symmetric.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This contains a small set of mostly fixes and some minor improvements.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAl4ZGs0THHRyZWRpbmdA
bnZpZGlhLmNvbQAKCRDdI6zXfz6zoZUkEACo+fhKHTmkCz4W+4m90aEFL/VUi7Bn
lFmssk2E71WvxUSWfLYawuhi/bgtMLvPmTi1KTCpvdvr+ladF1f4/Vd6vuhMu7Ec
t2ZePYmRlpX+3PHW+V2fIRyBC9/6wSx2UEAbcMOijIPHlWDNdrxo26w0+af0dBJ3
b8oIv5q5jX0GzZDOCOsBngUwnVzCYthVz7SA+UXOwBvNPO61kjx8IA/IfBHAQ+HF
ZVpn//C7g2/wHq125kdrFUwAWQPvFMHOs1JPfXS9248kobkIabSp0XxLaj403cFU
WWa/no5cPkG+WRwaX5egvE2/8P3mDzu3ev9gkgpdDJxnn1YL656mPWO7jNqW4IJd
JD8kTk7ODh7KQvY3xdHD3MrHpHWHtHdOiFZtOygiW84W2yK5/g/LRd/oph/xP1RE
/h8eiRP/mK7VkVRmgbiZTIEQVp10RKH56XtVd1Cf3eFNkig1Q8MLarwy2rhClyJO
7cJZKoOqRfx0aMYipxx5+YWDXrCVwtNrQKTroJ27ycre3ykv+NAoeHeei9ie81Rg
XZeCF3OuvVNXoUPQRS3XYkH70CTbdDTpkwymctcfwWOerhn65QAHvCSNR91ezmNq
YwC7CkS6ymeG9UhSoCvNoLa1adfeztRCwg8RkKdHgHFtHNNQuyRlp4xNyrJNgoCO
YX5dApw++iTOwQ==
=OBEv
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-5.6-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v5.6-rc1
This contains a small set of mostly fixes and some minor improvements.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200111004835.2412858-1-thierry.reding@gmail.com
Implement generic system suspend/resume functions that can be used with
any output type. Currently this only implements disabling and enabling
of the IRQ functionality across system suspend/resume. This prevents an
interrupt from happening before the display driver has fully resumed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Without CONFIG_PM, some functions cause harmless warnings:
drivers/gpu/drm/tegra/sor.c:3984:12: error: 'tegra_sor_resume' defined but not used [-Werror=unused-function]
static int tegra_sor_resume(struct device *dev)
^~~~~~~~~~~~~~~~
drivers/gpu/drm/tegra/sor.c:3970:12: error: 'tegra_sor_suspend' defined but not used [-Werror=unused-function]
static int tegra_sor_suspend(struct device *dev)
^~~~~~~~~~~~~~~~~
Mark these as __maybe_unused so the compiler can drop them
silently.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra DRM driver heavily relies on the implementations for runtime
suspend/resume to be called at specific times. Unfortunately, there are
some cases where that doesn't work. One example is if the user disables
runtime PM for a given subdevice. Another example is that the PM core
acquires a reference to runtime PM during system sleep, effectively
preventing devices from going into low power modes. This is intentional
to avoid nasty race conditions, but it also causes system sleep to not
function properly on all Tegra systems.
Fix this by not implementing runtime PM at all. Instead, a minimal,
reference-counted suspend/resume infrastructure is added to the host1x
bus. This has the benefit that it can be used regardless of the system
power state (or any transitions we might be in), or whether or not the
user allows runtime PM.
Atomic modesetting guarantees that these functions will end up being
called at the right point in time, so the pitfalls for the more generic
runtime PM do not apply here.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rename the host1x clients' parent to "host" because that more closely
describes what it is. The parent can be confused with the parent device
in terms of the device hierarchy. Subsequent patches will add a new
member that refers to the parent in that hierarchy.
Signed-off-by: Thierry Reding <treding@nvidia.com>
UAPI Changes:
- Add support for DMA-BUF HEAPS.
Cross-subsystem Changes:
- mipi dsi definition updates, pulled into drm-intel as well.
- Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim.
- Remove support for dma-buf kmap/kunmap.
- Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well.
Core Changes:
- Small cleanups to ttm.
- Fix SCDC definition.
- Assorted cleanups to core.
- Add todo to remove load/unload hooks, and use generic fbdev emulation.
- Assorted documentation updates.
- Use blocking ww lock in ttm fault handler.
- Remove drm_fb_helper_fbdev_setup/teardown.
- Warning fixes with W=1 for atomic.
- Use drm_debug_enabled() instead of drm_debug flag testing in various drivers.
- Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted)
- Various kconfig indentation fixes in core and drivers.
- Fix freeing transactions in dp-mst correctly.
- Sean Paul is steping down as core maintainer. :-(
- Add lockdep annotations for atomic locks vs dma-resv.
- Prevent use-after-free for a bad job in drm_scheduler.
- Fill out all block sizes in the P01x and P210 definitions.
- Avoid division by zero in drm/rect, and fix bounds.
- Add drm/rect selftests.
- Add aspect ratio and alternate clocks for HDMI 4k modes.
- Add todo for drm_framebuffer_funcs and fb_create cleanup.
- Drop DRM_AUTH for prime import/export ioctls.
- Clear DP-MST payload id tables downstream when initializating.
- Fix for DSC throughput definition.
- Add extra FEC definitions.
- Fix fake offset in drm_gem_object_funs.mmap.
- Stop using encoder->bridge in core directly
- Handle bridge chaining slightly better.
- Add backlight support to drm/panel, and use it in many panel drivers.
- Increase max number of y420 modes from 128 to 256, as preparation to add the new modes.
Driver Changes:
- Small fixes all over.
- Fix documentation in vkms.
- Fix mmap_sem vs dma_resv in nouveau.
- Small cleanup in komeda.
- Add page flip support in gma500 for psb/cdv.
- Add ddc symlink in the connector sysfs directory for many drivers.
- Add support for analogic an6345, and fix small bugs in it.
- Add atomic modesetting support to ast.
- Fix radeon fault handler VMA race.
- Switch udl to use generic shmem helpers.
- Unconditional vblank handling for mcde.
- Miscellaneous fixes to mcde.
- Tweak debug output from komeda using debugfs.
- Add gamma and color transform support to komeda for DOU-IPS.
- Add support for sony acx424AKP panel.
- Various small cleanups to gma500.
- Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation.
- Add support for Logic PD Type 28 panel.
- Use drm_panel_* wrapper functions in exynos/tegra/msm.
- Add devicetree bindings for generic DSI panels.
- Don't include drm_pci.h directly in many drivers.
- Add support for begin/end_cpu_access in udmabuf.
- Stop using drm_get_pci_dev in gma500 and mga200.
- Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access.
- Add devfreq thermal support to panfrost.
- Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager.
- meson: Add support for OSD1 plane AFBC commit.
- Stop displaying garbage when toggling ast primary plane on/off.
- More cleanups and fixes to UDL.
- Add D32 suport to komeda.
- Remove globle copy of drm_dev in gma500.
- Add support for Boe Himax8279d MIPI-DSI LCD panel.
- Add support for ingenic JZ4770 panel.
- Small null pointer deference fix in ingenic.
- Remove support for the special tfp420 driver, as there is a generic way to do it.
-----BEGIN PGP SIGNATURE-----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=b15X
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-12-16' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.6:
UAPI Changes:
- Add support for DMA-BUF HEAPS.
Cross-subsystem Changes:
- mipi dsi definition updates, pulled into drm-intel as well.
- Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim.
- Remove support for dma-buf kmap/kunmap.
- Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well.
Core Changes:
- Small cleanups to ttm.
- Fix SCDC definition.
- Assorted cleanups to core.
- Add todo to remove load/unload hooks, and use generic fbdev emulation.
- Assorted documentation updates.
- Use blocking ww lock in ttm fault handler.
- Remove drm_fb_helper_fbdev_setup/teardown.
- Warning fixes with W=1 for atomic.
- Use drm_debug_enabled() instead of drm_debug flag testing in various drivers.
- Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted)
- Various kconfig indentation fixes in core and drivers.
- Fix freeing transactions in dp-mst correctly.
- Sean Paul is steping down as core maintainer. :-(
- Add lockdep annotations for atomic locks vs dma-resv.
- Prevent use-after-free for a bad job in drm_scheduler.
- Fill out all block sizes in the P01x and P210 definitions.
- Avoid division by zero in drm/rect, and fix bounds.
- Add drm/rect selftests.
- Add aspect ratio and alternate clocks for HDMI 4k modes.
- Add todo for drm_framebuffer_funcs and fb_create cleanup.
- Drop DRM_AUTH for prime import/export ioctls.
- Clear DP-MST payload id tables downstream when initializating.
- Fix for DSC throughput definition.
- Add extra FEC definitions.
- Fix fake offset in drm_gem_object_funs.mmap.
- Stop using encoder->bridge in core directly
- Handle bridge chaining slightly better.
- Add backlight support to drm/panel, and use it in many panel drivers.
- Increase max number of y420 modes from 128 to 256, as preparation to add the new modes.
Driver Changes:
- Small fixes all over.
- Fix documentation in vkms.
- Fix mmap_sem vs dma_resv in nouveau.
- Small cleanup in komeda.
- Add page flip support in gma500 for psb/cdv.
- Add ddc symlink in the connector sysfs directory for many drivers.
- Add support for analogic an6345, and fix small bugs in it.
- Add atomic modesetting support to ast.
- Fix radeon fault handler VMA race.
- Switch udl to use generic shmem helpers.
- Unconditional vblank handling for mcde.
- Miscellaneous fixes to mcde.
- Tweak debug output from komeda using debugfs.
- Add gamma and color transform support to komeda for DOU-IPS.
- Add support for sony acx424AKP panel.
- Various small cleanups to gma500.
- Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation.
- Add support for Logic PD Type 28 panel.
- Use drm_panel_* wrapper functions in exynos/tegra/msm.
- Add devicetree bindings for generic DSI panels.
- Don't include drm_pci.h directly in many drivers.
- Add support for begin/end_cpu_access in udmabuf.
- Stop using drm_get_pci_dev in gma500 and mga200.
- Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access.
- Add devfreq thermal support to panfrost.
- Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager.
- meson: Add support for OSD1 plane AFBC commit.
- Stop displaying garbage when toggling ast primary plane on/off.
- More cleanups and fixes to UDL.
- Add D32 suport to komeda.
- Remove globle copy of drm_dev in gma500.
- Add support for Boe Himax8279d MIPI-DSI LCD panel.
- Add support for ingenic JZ4770 panel.
- Small null pointer deference fix in ingenic.
- Remove support for the special tfp420 driver, as there is a generic way to do it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ba73535a-9334-5302-2e1f-5208bd7390bd@linux.intel.com
The call to tegra_display_hub_cleanup() that takes care of disabling the
window groups is missing from the driver's ->remove() callback. Call it
to make sure the runtime PM reference counts for the display controllers
are balanced.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR supports multiple display modes, but only when driving an HDMI
monitor does it make sense to control the +5V power supply. eDP and DP
don't need this, so make it optional.
This fixes a crash observed during system suspend/resume.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Subdevices may not be hooked up to an IOMMU via device tree. Detect such
situations and avoid confusing users by not emitting an error message.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Export the module device table to ensure the VIC compatible strings are
listed in the module's aliases table. This in turn causes the driver to
be automatically loaded on boot if VIC is the only enabled subdevice of
the logical host1x DRM device.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Upon system suspend, make sure the +5V HDMI regulator is disabled. This
avoids potentially leaking current to the HDMI connector. This also
makes sure that upon resume the regulator is enabled again, which in
some cases is necessary to properly restore the state of the supply on
resume.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The IOVA address for the cursor is the result of mapping the buffer
object for the given display controller. Make sure to use the proper
IOVA address as stored in the cursor's plane state.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
All the display related blocks on Tegra require contiguous memory. Using
the DMA API, there is no knowing at import time which device will end up
using the buffer, so it's not known whether or not an IOMMU will be used
to map the buffer.
Move the check for non-contiguous buffers/mappings to the tegra_dc_pin()
function which is now the earliest point where it is known if a DMA BUF
can be used by the given device or not.
v2: add check for contiguous buffer/mapping in tegra_dc_pin()
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Buffers that are imported from a DMA-BUF don't have pages allocated with
them. At the same time an SG table for them can't be derived using the
DMA API helpers because the necessary information doesn't exist. However
there's already an SG table that was created during import, so this can
simply be duplicated.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra DRM never actually took that lock, so the driver was broken
until generic locking was added in commit:
commit b962a12050
Author: Rob Clark <robdclark@gmail.com>
Date: Mon Oct 22 14:31:22 2018 +0200
drm/atomic: integrate modeset lock with private objects
It's now no longer necessary to take that lock, so drop the check.
v2: add rationale for why it is now safe to drop the check (Daniel)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
It doesn't have any callers anymore.
Aside: The ->mmap/munmap hooks have a bit a confusing name, they don't
do userspace mmaps, but a kernel vmap. I think most places use vmap
for this, except ttm, which uses kmap for vmap for added confusion.
mmap seems entirely for userspace mappings set up through mmap(2)
syscall.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20191118103536.17675-3-daniel.vetter@ffwll.ch
Currently configurations can be generated where IOMMU_SUPPORT is
disabled but IOMMU_IOVA is built as a module and DRM_TEGRA as built-in.
In such a case, the symbols guarded by IOMMU_IOVA will not be available
when linking the Tegra DRM driver and cause a linking failure.
Simplify this by unconditionally selecting IOMMU_IOVA, which makes sure
that it will be forced to =y if DRM_TEGRA=y. Technically we can now get
IOMMU_IOVA code built-in even if we don't use it (Tegra DRM only uses it
when IOMMU_SUPPORT is also enabled), but such configuration are of a
mostly academic nature. In all practical configurations we want IOMMU
support anyway.
Signed-off-by: Thierry Reding <treding@nvidia.com>
If a client is already attached to an IOMMU domain that is not the
shared domain, don't try to attach it again. This allows using the
IOMMU-backed DMA API.
Since the IOMMU-backed DMA API is now supported and there's no way
to detach from it on 64-bit ARM, don't bother to detach from it on
32-bit ARM either.
Signed-off-by: Thierry Reding <treding@nvidia.com>
If a display controller is not attached to an explicit IOMMU domain,
which usually means that it's connected to an IOMMU domain controlled by
the DMA API, make sure to map the framebuffer to the display controller
address space. This allows us to transparently handle setups where the
display controller is attached to an IOMMU or setups where it isn't. It
also allows the driver to work with a DMA API that is backed by an
IOMMU.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rename paddr -> iova and vaddr -> virt to make it clearer how these
addresses are used. This is important for a subsequent patch that makes
a distinction between the physical address (physical address of the
system memory from the CPU's point of view) and the IOVA (physical
address of the system memory from the device's point of view).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Having to provide allocator hooks to the Falcon library is somewhat
cumbersome and it doesn't give the users of the library a lot of
flexibility to deal with allocations. Instead, remove the notion of
Falcon "operations" and let drivers deal with the memory allocations
themselves.
Signed-off-by: Thierry Reding <treding@nvidia.com>
If host1x_bo_pin() returns an SG table, create a DMA mapping for the
buffer. For buffers that the host1x client has already mapped itself,
host1x_bo_pin() returns NULL and the existing DMA address is used.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add direction flags to host1x relocations performed during job pinning.
These flags indicate the kinds of accesses that hardware is allowed to
perform on the relocated buffers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The host1x_bo_pin() and host1x_bo_unpin() APIs are used to pin and unpin
buffers during host1x job submission. Pinning currently returns the SG
table and the DMA address (an IOVA if an IOMMU is used or a physical
address if no IOMMU is used) of the buffer. The DMA address is only used
for buffers that are relocated, whereas the host1x driver will map
gather buffers into its own IOVA space so that they can be processed by
the CDMA engine.
This approach has a couple of issues. On one hand it's not very useful
to return a DMA address for the buffer if host1x doesn't need it. On the
other hand, returning the SG table of the buffer is suboptimal because a
single SG table cannot be shared for multiple mappings, because the DMA
address is stored within the SG table, and the DMA address may be
different for different devices.
Subsequent patches will move the host1x driver over to the DMA API which
doesn't work with a single shared SG table. Fix this by returning a new
SG table each time a buffer is pinned. This allows the buffer to be
referenced by multiple jobs for different engines.
Change the prototypes of host1x_bo_pin() and host1x_bo_unpin() to take a
struct device *, specifying the device for which the buffer should be
pinned. This is required in order to be able to properly construct the
SG table. While at it, make host1x_bo_pin() return the SG table because
that allows us to return an ERR_PTR()-encoded error code if we need to,
or return NULL to signal that we don't need the SG table to be remapped
and can simply use the DMA address as-is. At the same time, returning
the DMA address is made optional because in the example of command
buffers, host1x doesn't need to know the DMA address since it will have
to create its own mapping anyway.
Signed-off-by: Thierry Reding <treding@nvidia.com>
All the devices that make up the DRM device are now part of the same
IOMMU group. This simplifies the handling of the IOMMU attachment and
also avoids exhausting the number of IOMMUs available on early Tegra
SoC generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ->load() and ->unload() drivers are midlayers and should be avoided
in modern drivers. Fix this by moving the code into the driver ->probe()
and ->remove() implementations, respectively.
v2: kick out conflicting framebuffers before initializing fbdev
v3: rebase onto drm/tegra/for-next
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to support different modes (DP in addition to HDMI), split out
the audio setup/teardown into callbacks.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The code to enable audio support is split into two parts, one being
generic for the SOR and another part that is specific whether the SOR is
in HDMI mode or in DP mode. Split out the common part in preparation for
reusing the code in DP mode.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the SOR is disabled in DP mode as part of an unplug event, do not
attempt to power the DP link down. Powering down the link requires the
DPAUX to transmit AUX messages which only works if there's a connected
sink.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR0 on Tegra210 does, contrary to what was previously assumed, in
fact support DisplayPort. The difference between SOR0 and SOR1 is that
the latter supports audio and HDCP over DP, whereas the former doesn't.
The code for eDP and DP is now almost identical and the differences can
easily be parameterized based on the presence of a panel. There is no
need any longer to duplicate the code.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The correct I/O pad needs to be powered up before DP can be used. Make
sure the correct default is set for Tegra generations where the I/O pad
cannot be derived from the SOR instance.
Signed-off-by: Thierry Reding <treding@nvidia.com>
With the clocks modelled consistently across SoC generations, the clock
setup for eDP, HDMI and DP can now be unified.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The connector type detection code is duplicated in two places. Keeping
both places in sync is an extra maintenance burden that can be avoided
by comparing the connector type operations that are set upon the first
detection.
Signed-off-by: Thierry Reding <treding@nvidia.com>
So far the pad clock was only needed on the second SOR instance. The
clock does exist for all SOR instances, though, so make sure it is
always implemented. This prepares for further unification of the code
in subsequent patches.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The device tree bindings for the Tegra210 SOR don't require the
controller instance to be defined, since the instance can be derived
from the compatible string. The index is never used on Tegra210, so we
got away with it not getting set. However, subsequent patches will
change that, so make sure the proper index is used.
Signed-off-by: Thierry Reding <treding@nvidia.com>
It turns out that SOR1 is just another instance of the same block as the
SOR0, so there is no need to distinguish them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR found on Tegra SoCs does not support all the rates potentially
advertised by eDP 1.4. Make sure that the rates that are not supported
are filtered out.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rework eDP code to correspond more closely to what's documented. This
also improves the reliability of modesets.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This is necessary for the output abstraction to retrieve a list of valid
modes from the EDID of a connected panel/monitor. This will be useful in
conjunction with DisplayPort support that will be added in a subsequent
patch, so that the driver can read EDID via the AUX channel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Make use of the DP link training helpers to implement full and fast link
training. While at it, refactor some of the code and remove various code
sequences that are not necessary.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This helper chooses an appropriate configuration, according to the
bitrate requirements of the video mode and the capabilities of the
DisplayPort sink.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Store the AUX read interval from DPCD, so that it can be used to wait
for the durations given in the specification during link training.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Parse from the sink capabilities whether or not the eDP alternate
scrambler reset value of 0xfffe is supported.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Parse from the sink capabilities whether or not it supports ANSI 8B/10B
channel coding as specified in ANSI X3.230-1994, clause 11.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The TPS3 capability can be exposed by DP 1.2 and later sinks if they
support the alternative training pattern for channel equalization.
Signed-off-by: Thierry Reding <treding@nvidia.com>
While probing the DisplayPort link, query the fast training capability.
If supported, drivers can use the fast link training sequence instead of
the more involved full link training sequence.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rather than storing capabilities as flags in an integer, use a separate
boolean per capability. This simplifies the code that checks for these
capabilities.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Subsequent patches will add non-volatile fields to struct drm_dp_link,
so introduce a function to zero out only the volatile fields.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The drm_dp_link structure tracks capabilities on the DP link. Add some
kerneldoc to explain what each of its fields means.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The CMH, DRVZ and DRVI values vary depending on the SoC generation. Move
them into SoC specific structures so that DT compatible string matching
can be used to select the right parameters and write them to hardware at
the right time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to properly make the VDD supply optional, all accesses to the
regulator need to be ignored, because the regulator core doesn't treat
NULL special.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When a transfer didn't complete transmission of the requested number of
bytes, signal that the transaction should be retried.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The dpaux driver has a quirk built-in that will delay initialization of
the display driver for a short while, trying to detect an eDP panel. The
reason for this quirk is that the panel may not report as connected
until after the display driver has initialized, at which point the fbdev
emulation will have fallen back to 1024x768 as default resolution, which
will likely not be the eDP panel's native resolution.
With upcoming DisplayPort support, the code needs to be able to cope
with hotpluggable monitors as well. Waiting for a panel to show up is no
longer going to work because the monitor may not be attached on boot. If
the output runs in DisplayPort mode, skip waiting for the panel to show
up.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of manually creating the SG table for a discontiguous buffer,
use the existing sg_alloc_table_from_pages(). Note that this is not safe
to be used with the ARM DMA/IOMMU integration code because that will not
ensure that the whole buffer is mapped contiguously. Depending on the
size of the individual entries the mapping may end up containing holes
to ensure alignment.
However, we only ever use these buffers with explicit IOMMU API usage
and know how to avoid these holes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When an importer wants to map a DMA-BUF, make sure to always actually
map it, irrespective of whether the buffer is contiguous or not.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rather than manually creating an SG table in an incorrect way, let the
standard dma_get_sgtable() function do it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The address can refer to either physical memory or IO virtual memory.
If referring to IO virtual memory, there will always be an associated
physical memory address. Rename this variable to "iova" to clarify in
all cases that this is the IO virtual memory, which in the absence of
an IOMMU is identical to the physical address.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Handling of the IOMMU group attachment is common to all clients, so move
the group into the client to simplify code.
Signed-off-by: Thierry Reding <treding@nvidia.com>
VIC, just like all other host1x clients, has the same addressing range
as its parent host1x device. Inherit the DMA mask to reflect that.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The driver-specific messages should use the DRM_UT_DRIVER category so
that they can be properly filtered.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The display controllers and VIC don't have any limitations on the
DMA segment size. Inherit the DMA parameters from the parent device,
which also doesn't have any such limitations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
A struct device doesn't carry much information that a channel might be
interested in, but the client very much does. Request channels for the
clients rather than their parent devices and store a pointer to them
in order to have that information available when needed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the new cec_notifier_conn_(un)register() functions to
(un)register the notifier for the HDMI connector, and fill in
the cec_connector_info.
Signed-off-by: Dariusz Marcinkiewicz <darekm@google.com>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit Fixes: b9f8b09ce2 ("drm/tegra: Setup shared IOMMU domain after
initialization") changed the initialization order of the IOMMU related
bits but didn't update the cleanup path accordingly. This asymmetry can
cause failures during error recovery.
Fixes: b9f8b09ce2 ("drm/tegra: Setup shared IOMMU domain after initialization")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
The hardware is not guaranteed to be enabled during execution of the
tegra_sor_init() function, which can lead to a crash on some Tegra SoCs.
Fix this by moving all register programming into code that is guaranteed
to only be executed when the hardware is enabled.
Signed-off-by: Thierry Reding <treding@nvidia.com>
During the discussion of patches that enhance the drm_dp_link helpers it
was concluded that these helpers aren't very useful to begin with. After
all other drivers have been converted not to use these helpers anymore,
move these helpers into the last remaining user: Tegra DRM.
If at some point these helpers are deemed more widely useful, they can
be moved out into the DRM DP helpers again.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20191021143437.1477719-14-thierry.reding@gmail.com
-----BEGIN PGP SIGNATURE-----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=5CRH
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-09-18' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This is the main pull request for 5.4-rc1 merge window. I don't think
there is anything outstanding so next week should just be fixes, but
we'll see if I missed anything. I landed some fixes earlier in the
week but got delayed writing summary and sending it out, due to a mix
of sick kid and jetlag!
There are some fixes pending, but I'd rather get the main merge out of
the way instead of delaying it longer.
It's also pretty large in commit count and new amd header file size.
The largest thing is four new amdgpu products (navi12/14, arcturus and
renoir APU support).
Otherwise it's pretty much lots of work across the board, i915 has
started landing tigerlake support, lots of icelake fixes and lots of
locking reworking for future gpu support, lots of header file rework
(drmP.h is nearly gone), some old legacy hacks (DRM_WAIT_ON) have been
put into the places they are needed.
uapi:
- content protection type property for HDCP
core:
- rework include dependencies
- lots of drmP.h removals
- link rate calculation robustness fix
- make fb helper map only when required
- add connector->DDC adapter link
- DRM_WAIT_ON removed
- drop DRM_AUTH usage from drivers
dma-buf:
- reservation object fence helper
dma-fence:
- shrink dma_fence struct
- merge signal functions
- store timestamps in dma_fence
- selftests
ttm:
- embed drm_get_object struct into ttm_buffer_object
- release_notify callback
bridges:
- sii902x - audio graph card support
- tc358767 - aux data handling rework
- ti-snd64dsi86 - debugfs support, DSI mode flags support
panels:
- Support for GiantPlus GPM940B0, Sharp LQ070Y3DG3B, Ortustech
COM37H3M, Novatek NT39016, Sharp LS020B1DD01D, Raydium RM67191, Boe
Himax8279d, Sharp LD-D5116Z01B
- TI nspire, NEC NL8048HL11, LG Philips LB035Q02, Sharp LS037V7DW01,
Sony ACX565AKM, Toppoly TD028TTEC1 Toppoly TD043MTEA1
i915:
- Initial tigerlake platform support
- Locking simplification work, general all over refactoring.
- Selftests
- HDCP debug info improvements
- DSI properties
- Icelake display PLL fixes, colorspace fixes, bandwidth fixes, DSI
suspend/resume
- GuC fixes
- Perf fixes
- ElkhartLake enablement
- DP MST fixes
- GVT - command parser enhancements
amdgpu:
- add wipe memory on release flag for buffer creation
- Navi12/14 support (may be marked experimental)
- Arcturus support
- Renoir APU support
- mclk DPM for Navi
- DC display fixes
- Raven scatter/gather support
- RAS support for GFX
- Navi12 + Arcturus power features
- GPU reset for Picasso
- smu11 i2c controller support
amdkfd:
- navi12/14 support
- Arcturus support
radeon:
- kexec fix
nouveau:
- improved display color management
- detect lack of GPU power cables
vmwgfx:
- evicition priority support
- remove unused security feature
msm:
- msm8998 display support
- better async commit support for cursor updates
etnaviv:
- per-process address space support
- performance counter fixes
- softpin support
mcde:
- DCS transfers fix
exynos:
- drmP.h cleanup
lima:
- reduce logging
kirin:
- misc clenaups
komeda:
- dual-link support
- DT memory regions
hisilicon:
- misc fixes
imx:
- IPUv3 image converter fixes
- 32-bit RGB V4L2 pixel format support
ingenic:
- more support for panel related cases
mgag200:
- cursor support fix
panfrost:
- export GPU features register to userspace
- gpu heap allocations
- per-fd address space support
pl111:
- CLD pads wiring support removed from DT
rockchip:
- rework to use DRM PSR helpers
- fix bug in VOP_WIN_GET macro
- DSI DT binding rework
sun4i:
- improve support for color encoding and range
- DDC enabled GPIO
tinydrm:
- rework SPI support
- improve MIPI-DBI support
- moved to drm/tiny
vkms:
- rework CRC tracking
dw-hdmi:
- get_eld and i2s improvements
gm12u320:
- misc fixes
meson:
- global code cleanup
- vpu feature detect
omap:
- alpha/pixel blend mode properties
rcar-du:
- misc fixes"
* tag 'drm-next-2019-09-18' of git://anongit.freedesktop.org/drm/drm: (2112 commits)
drm/nouveau/bar/gm20b: Avoid BAR1 teardown during init
drm/nouveau: Fix ordering between TTM and GEM release
drm/nouveau/prime: Extend DMA reservation object lock
drm/nouveau: Fix fallout from reservation object rework
drm/nouveau/kms/nv50-: Don't create MSTMs for eDP connectors
drm/i915: Use NOEVICT for first pass on attemping to pin a GGTT mmap
drm/i915: to make vgpu ppgtt notificaiton as atomic operation
drm/i915: Flush the existing fence before GGTT read/write
drm/i915: Hold irq-off for the entire fake lock period
drm/i915/gvt: update RING_START reg of vGPU when the context is submitted to i915
drm/i915/gvt: update vgpu workload head pointer correctly
drm/mcde: Fix DSI transfers
drm/msm: Use the correct dma_sync calls harder
drm/msm: remove unlikely() from WARN_ON() conditions
drm/msm/dsi: Fix return value check for clk_get_parent
drm/msm: add atomic traces
drm/msm/dpu: async commit support
drm/msm: async commit support
drm/msm: split power control from prepare/complete_commit
drm/msm: add kms->flush_commit()
...
Drop use of the deprecated drmP.h header file.
For all touched files divide include files into blocks,
and sort them within the blocks.
Fix fallout.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190804094132.29463-3-sam@ravnborg.org
That function now returns ERR_PTR instead of NULL if "hpd-gpio" is not
present in device-tree. The offending patch missed to adapt the Tegra's
DRM driver for the API change.
Fixes: 025bf37725 ("gpio: Fix return value mismatch of function gpiod_get_from_of_node()")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
This contains a couple of small improvements and cleanups for the Tegra
DRM driver.
-----BEGIN PGP SIGNATURE-----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=T2hU
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-5.3-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v5.3-rc1
This contains a couple of small improvements and cleanups for the Tegra
DRM driver.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190621150753.19550-1-thierry.reding@gmail.com
The driver_find_device() accepts a match function pointer to
filter the devices for lookup, similar to bus/class_find_device().
However, there is a minor difference in the prototype for the
match parameter for driver_find_device() with the now unified
version accepted by {bus/class}_find_device(), where it doesn't
accept a "const" qualifier for the data argument. This prevents
us from reusing the generic match functions for driver_find_device().
For this reason, change the prototype of the driver_find_device() to
make the "match" parameter in line with {bus/class}_find_device()
and adjust its callers to use the const qualifier. Also, we could
now promote the "data" parameter to const as we pass it down
as a const parameter to the match functions.
Cc: Corey Minyard <minyard@acm.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Sebastian Ott <sebott@linux.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Nehal Shah <nehal-bakulchandra.shah@amd.com>
Cc: Shyam Sundar S K <shyam-sundar.s-k@amd.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The idea is that gem_prime_export is deprecated in favor of
obj_funcs.export. That's much easier to do if both have matching
function signatures.
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: "Michel Dänzer" <michel.daenzer@amd.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Huang Rui <ray.huang@amd.com>
Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: Hawking Zhang <Hawking.Zhang@amd.com>
Cc: Feifei Xu <Feifei.Xu@amd.com>
Cc: Jim Qu <Jim.Qu@amd.com>
Cc: Evan Quan <evan.quan@amd.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Thomas Zimmermann <tdz@users.sourceforge.net>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Jilayne Lovejoy <opensource@jilayne.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Junwei Zhang <Jerry.Zhang@amd.com>
Cc: intel-gvt-dev@lists.freedesktop.org
Cc: intel-gfx@lists.freedesktop.org
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-tegra@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190614203615.12639-10-daniel.vetter@ffwll.ch
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VDD supply is only needed to supply power to eDP panels connected to
DPAUX. Technically that supply should be dealt with in the panel driver,
but for backwards-compatibility we need to keep this around anyway.
Also as a bit of background: the reason for why this supply is attached
to DPAUX is to make sure the panel is properly powered early on so that
it can generate a hotplug pulse at the appropriate time. This may no
longer be required given the support for deferred fbdev setup that was
"recently" introduced in DRM/KMS.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The legacy GPIO API has long been deprecated. Move the driver over to
the descriptor-based API, which allows us to get rid of some boilerplate
while at it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Cross-subsystem Changes:
- Fix device tree bindings in drm-misc-next after a botched merge.
Core Changes:
- Docbook fix for drm_hdmi_infoframe_set_hdr_metadata.
Driver Changes:
- mediatek: Fix compiler warning after merging the HDR series.
- vc4: Rework binner bo handling.
-----BEGIN PGP SIGNATURE-----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=2K7c
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-05-24' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.3, try #2:
UAPI Changes:
- Add HDR source metadata property.
- Make drm.h compile on GNU/kFreeBSD by including stdint.h
- Clarify how the userspace reviewer has to review new kernel UAPI.
- Clarify that for using new UAPI, merging to drm-next or drm-misc-next should be enough.
Cross-subsystem Changes:
- video/hdmi: Add unpack function for DRM infoframes.
- Device tree bindings:
* Updating a property for Mali Midgard GPUs
* Updating a property for STM32 DSI panel
* Adding support for FriendlyELEC HD702E 800x1280 panel
* Adding support for Evervision VGG804821 800x480 5.0" WVGA TFT panel
* Adding support for the EDT ET035012DM6 3.5" 320x240 QVGA 24-bit RGB TFT.
* Adding support for Three Five displays TFC S9700RTWV43TR-01B 800x480 panel
with resistive touch found on TI's AM335X-EVM.
* Adding support for EDT ETM0430G0DH6 480x272 panel.
- Add OSD101T2587-53TS driver with DT bindings.
- Add Samsung S6E63M0 panel driver with DT bindings.
- Add VXT VL050-8048NT-C01 800x480 panel with DT bindings.
- Dma-buf:
- Make mmap callback actually optional.
- Documentation updates.
- Fix debugfs refcount inbalance.
- Remove unused sync_dump function.
- Fix device tree bindings in drm-misc-next after a botched merge.
Core Changes:
- Add support for HDR infoframes and related EDID parsing.
- Remove prime sg_table caching, now done inside dma-buf.
- Add shiny new drm_gem_vram helpers for simple VRAM drivers;
with some fixes to the new API on top.
- Small fix to job cleanup without timeout handler.
- Documentation fixes to drm_fourcc.
- Replace lookups of drm_format with struct drm_format_info;
remove functions that become obsolete by this conversion.
- Remove double include in bridge/panel.c and some drivers.
- Remove drmP.h include from drm/edid and drm/dp.
- Fix null pointer deref in drm_fb_helper_hotplug_event().
- Remove most members from drm_fb_helper_crtc, only mode_set is kept.
- Remove race of fb helpers with userspace; only restore mode
when userspace is not master.
- Move legacy setup from drm_file.c to drm_legacy_misc.c
- Rework scheduler job destruction.
- drm/bus was removed, remove from TODO.
- Add __drm_atomic_helper_crtc_reset() to subclass crtc_state,
and convert some drivers to use it (conversion is not complete yet).
- Bump vblank timeout wait to 100 ms for atomic.
- Docbook fix for drm_hdmi_infoframe_set_hdr_metadata.
Driver Changes:
- sun4i: Use DRM_GEM_CMA_VMAP_DRIVER_OPS instead of definining manually.
- v3d: Small cleanups, adding support for compute shaders,
reservation/synchronization fixes and job management refactoring,
fixes MMU and debugfs.
- lima: Fix null pointer in irq handler on startup, set default timeout for scheduled jobs.
- stm/ltdc: Assorted fixes and adding FB modifier support.
- amdgpu: Avoid hw reset if guilty job was already signaled.
- virtio: Add seqno to fences, add trace events, use correct flags for fence allocation.
- Convert AST, bochs, mgag200, vboxvideo, hisilicon to the new drm_gem_vram API.
- sun6i_mipi_dsi: Support DSI GENERIC_SHORT_WRITE_2 transfers.
- bochs: Small fix to use PTR_RET_OR_ZERO and driver unload.
- gma500: header fixes
- cirrus: Remove unused files.
- mediatek: Fix compiler warning after merging the HDR series.
- vc4: Rework binner bo handling.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/052875a5-27ba-3832-60c2-193d950afdff@linux.intel.com
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So far, the drm_format_plane_cpp function was operating on the format's
fourcc and was doing a lookup to retrieve the drm_format_info structure and
return the cpp.
However, this is inefficient since in most cases, we will have the
drm_format_info pointer already available so we shouldn't have to perform a
new lookup. Some drm_fourcc functions also already operate on the
drm_format_info pointer for that reason, so the API is quite inconsistent
there.
Let's follow the latter pattern and remove the extra lookup while being a
bit more consistent. In order to be extra consistent, also rename that
function to drm_format_info_plane_cpp and to a static function in the
header to match the current policy.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/32aa13e53dbc98a90207fd290aa8e79f785fb11e.1558002671.git-series.maxime.ripard@bootlin.com
drm_format_horz_chroma_subsampling and drm_format_vert_chroma_subsampling
are basically a lookup in the drm_format_info table plus an access to the
hsub and vsub fields of the appropriate entry.
Most drivers are using this function while having access to the entry
already, which means that we will perform an unnecessary lookup. Removing
the call to these functions is therefore more efficient.
Some drivers will not have access to that entry in the function, but in
this case the overhead is minimal (we just have to call drm_format_info()
to perform the lookup) and we can even avoid multiple, inefficient lookups
in some places that need multiple fields from the drm_format_info
structure.
This is amplified by the fact that most of the time the callers will have
to retrieve both the vsub and hsub fields, meaning that they would perform
twice the lookup.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6b3cceb8161e2c1d40c2681de99202328b0a8abc.1558002671.git-series.maxime.ripard@bootlin.com
drm_format_num_planes() is basically a lookup in the drm_format_info table
plus an access to the num_planes field of the appropriate entry.
Most drivers are using this function while having access to the entry
already, which means that we will perform an unnecessary lookup. Removing
the call to drm_format_num_planes is therefore more efficient.
Some drivers will not have access to that entry in the function, but in
this case the overhead is minimal (we just have to call drm_format_info()
to perform the lookup) and we can even avoid multiple, inefficient lookups
in some places that need multiple fields from the drm_format_info
structure.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/5ffcec9d14a50ed538e37d565f546802452ee672.1558002671.git-series.maxime.ripard@bootlin.com
-----BEGIN PGP SIGNATURE-----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=YFiQ
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-05-09' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This has two exciting community drivers for ARM Mali accelerators.
Since ARM has never been open source friendly on the GPU side of the
house, the community has had to create open source drivers for the
Mali GPUs. Lima covers the older t4xx and panfrost the newer 6xx/7xx
series. Well done to all involved and hopefully this will help ARM
head in the right direction.
There is also now the ability if you don't have any of the legacy
drivers enabled (pre-KMS) to remove all the pre-KMS support code from
the core drm, this saves 10% or so in codesize on my machine.
i915 also enable Icelake/Elkhart Lake Gen11 GPUs by default, vboxvideo
moves out of staging.
There are also some rcar-du patches which crossover with media tree
but all should be acked by Mauro.
Summary:
uapi changes:
- Colorspace connector property
- fourcc - new YUV formts
- timeline sync objects initially merged
- expose FB_DAMAGE_CLIPS to atomic userspace
new drivers:
- vboxvideo: moved out of staging
- aspeed: ASPEED SoC BMC chip display support
- lima: ARM Mali4xx GPU acceleration driver support
- panfrost: ARM Mali6xx/7xx Midgard/Bitfrost acceleration driver support
core:
- component helper docs
- unplugging fixes
- devm device init
- MIPI/DSI rate control
- shmem backed gem objects
- connector, display_info, edid_quirks cleanups
- dma_buf fence chain support
- 64-bit dma-fence seqno comparison fixes
- move initial fb config code to core
- gem fence array helpers for Lima
- ability to remove legacy support code if no drivers requires it (removes 10% of drm.ko size)
- lease fixes
ttm:
- unified DRM_FILE_PAGE_OFFSET handling
- Account for kernel allocations in kernel zone only
panel:
- OSD070T1718-19TS panel support
- panel-tpo-td028ttec1 backlight support
- Ronbo RB070D30 MIPI/DSI
- Feiyang FY07024DI26A30-D MIPI-DSI panel
- Rocktech jh057n00900 MIPI-DSI panel
i915:
- Comet Lake (Gen9) PCI IDs
- Updated Icelake PCI IDs
- Elkhartlake (Gen11) support
- DP MST property addtions
- plane and watermark fixes
- Icelake port sync and VEBOX disable fixes
- struct_mutex usage reduction
- Icelake gamma fix
- GuC reset fixes
- make mmap more asynchronous
- sound display power well race fixes
- DDI/MIPI-DSI clocks for Icelake
- Icelake RPS frequency changing support
- Icelake workarounds
amdgpu:
- Use HMM for userptr
- vega20 experimental smu11 support
- RAS support for vega20
- BACO support for vega12 + fixes for vega20
- reworked IH interrupt handling
- amdkfd RAS support
- Freesync improvements
- initial timeline sync object support
- DC Z ordering fixes
- NV12 planes support
- colorspace properties for planes=
- eDP opts if eDP already initialized
nouveau:
- misc fixes
etnaviv:
- misc fixes
msm:
- GPU zap shader support expansion
- robustness ABI addition
exynos:
- Logging cleanups
tegra:
- Shared reset fix
- CPU cache maintenance fix
cirrus:
- driver rewritten using simple helpers
meson:
- G12A support
vmwgfx:
- Resource dirtying management improvements
- Userspace logging improvements
virtio:
- PRIME fixes
rockchip:
- rk3066 hdmi support
sun4i:
- DSI burst mode support
vc4:
- load tracker to detect underflow
v3d:
- v3d v4.2 support
malidp:
- initial Mali D71 support in komeda driver
tfp410:
- omap related improvement
omapdrm:
- drm bridge/panel support
- drop some omap specific panels
rcar-du:
- Display writeback support"
* tag 'drm-next-2019-05-09' of git://anongit.freedesktop.org/drm/drm: (1507 commits)
drm/msm/a6xx: No zap shader is not an error
drm/cma-helper: Fix drm_gem_cma_free_object()
drm: Fix timestamp docs for variable refresh properties.
drm/komeda: Mark the local functions as static
drm/komeda: Fixed warning: Function parameter or member not described
drm/komeda: Expose bus_width to Komeda-CORE
drm/komeda: Add sysfs attribute: core_id and config_id
drm: add non-desktop quirk for Valve HMDs
drm/panfrost: Show stored feature registers
drm/panfrost: Don't scream about deferred probe
drm/panfrost: Disable PM on probe failure
drm/panfrost: Set DMA masks earlier
drm/panfrost: Add sanity checks to submit IOCTL
drm/etnaviv: initialize idle mask before querying the HW db
drm: introduce a capability flag for syncobj timeline support
drm: report consistent errors when checking syncobj capibility
drm/nouveau/nouveau: forward error generated while resuming objects tree
drm/nouveau/fb/ramgk104: fix spelling mistake "sucessfully" -> "successfully"
drm/nouveau/i2c: Disable i2c bus access after ->fini()
drm/nouveau: Remove duplicate ACPI_VIDEO_NOTIFY_PROBE definition
...
Convert tegra to using __drm_atomic_helper_crtc_reset(), instead of
writing its own version. Instead of open coding destroy_state(),
call it directly for freeing the old state.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
[mlankhorst: Keep tegra_crtc_reset at the same place and predeclare
tegra_crtc_atomic_destroy_state (tagr)]
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190301125627.7285-15-maarten.lankhorst@linux.intel.com
This contains a fix for the usage of shared resets that previously
generated a WARN on boot. In addition, there's a fix for CPU cache
maintenance of GEM buffers allocated using get_pages().
-----BEGIN PGP SIGNATURE-----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=nA5m
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-5.2-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v5.2-rc1
This contains a fix for the usage of shared resets that previously
generated a WARN on boot. In addition, there's a fix for CPU cache
maintenance of GEM buffers allocated using get_pages().
(airlied: contains a merge from a shared tegra tree)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190418151447.9430-1-thierry.reding@gmail.com
The allocated pages need to be invalidated in CPU caches. On ARM32 the
DMA_BIDIRECTIONAL flag only ensures that data is written-back to DRAM and
the data stays in CPU cache lines. While the DMA_FROM_DEVICE flag ensures
that the corresponding CPU cache lines are getting invalidated and nothing
more, that's exactly what is needed for a newly allocated pages.
This fixes randomly failing rendercheck tests on Tegra30 using the
Opentegra driver for tests that use small-sized pixmaps (10x10 and less,
i.e. 1-2 memory pages) because apparently CPU reads out stale data from
caches and/or that data is getting evicted to DRAM at the time of HW job
execution.
Fixes: bd43c9f0fa ("drm/tegra: gem: Map pages via the DMA API")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The audio configuration is only valid if the HDMI codec has been
properly set up. Do not attempt to set up audio before that happens
because it causes a division by zero.
Note that this is only problematic on Tegra20 and Tegra30. Later chips
implement the division instructions which return zero when dividing by
zero and don't throw an exception.
Fixes: db5adf4d6d ("drm/tegra: hdmi: Fix audio to work with any pixel clock rate")
Reported-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Another driver that didn't set fbinfo->fix.id before.
v2: Fix subject and rebase
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-18-daniel.vetter@ffwll.ch
By implementing the acquire/release protocol, the SOR reset can be
shared with other drivers that also adhere to this protocol, such as the
PMC driver that uses the same reset as part of the powergate and -ungate
implementation using generic power domains.
Runtime PM makes sure that the operations are executed in the right
order, and the reset core has error handling and WARNs in place to make
sure the acquire/release protocol is followed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When CONFIG_IOMMU_API isn't set the following warnings pops up:
drivers/gpu/drm/tegra/vic.c: In function ‘vic_boot’:
drivers/gpu/drm/tegra/vic.c:110:31: error: implicit declaration of function ‘dev_iommu_fwspec_get’; did you mean ‘iommu_fwspec_free’? [-Werror=implicit-function-declaration]
struct iommu_fwspec *spec = dev_iommu_fwspec_get(vic->dev);
^~~~~~~~~~~~~~~~~~~~
iommu_fwspec_free
drivers/gpu/drm/tegra/vic.c:110:31: warning: initialization of ‘struct iommu_fwspec *’ from ‘int’ makes pointer from integer without a cast [-Wint-conversion]
drivers/gpu/drm/tegra/vic.c:117:19: error: ‘struct iommu_fwspec’ has no member named ‘num_ids’
if (spec && spec->num_ids > 0) {
^~
drivers/gpu/drm/tegra/vic.c:118:16: error: ‘struct iommu_fwspec’ has no member named ‘ids’
value = spec->ids[0] & 0xffff;
^~
Rework so that its inside a '#ifdef CONFIG_IOMMU_API' block.
Fixes: f3779cb190 ("drm/tegra: vic: Support stream ID register programming")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This set of changes starts of with some refactoring of the CEC support
to make it reusable on Tegra210 and later. Following are a couple of
fixes for HDMI audio support (via HDA).
The bulk here is a set of preparatory patches working towards enabling
Tegra186 support for host1x and VIC. Additional patches will be needed
to fully enable this, but they're not quite ready yet.
To round things off, this also adds support for configuring the SOR
crossbar using device tree, and fixes a couple of job-related issues in
the host1x code.
-----BEGIN PGP SIGNATURE-----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=jS/6
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-5.1-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v5.1-rc1
This set of changes starts of with some refactoring of the CEC support
to make it reusable on Tegra210 and later. Following are a couple of
fixes for HDMI audio support (via HDA).
The bulk here is a set of preparatory patches working towards enabling
Tegra186 support for host1x and VIC. Additional patches will be needed
to fully enable this, but they're not quite ready yet.
To round things off, this also adds support for configuring the SOR
crossbar using device tree, and fixes a couple of job-related issues in
the host1x code.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190208144721.25830-1-thierry.reding@gmail.com
The crossbar configuration is usually the same across all designs for a
given SoC generation. But sometimes there are designs that require some
other configuration.
Implement support for parsing the crossbar configuration from a device
tree. If the crossbar configuration is not present in the device tree,
fall back to the default crossbar configuration.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The version of VIC found in Tegra186 and later incorporates improvements
with regards to context isolation. As part of those improvements, stream
ID registers were added that allow to specify separate stream IDs for
the Falcon microcontroller and the VIC memory interface.
While it is possible to also set the stream ID dynamically at runtime to
allow userspace contexts to be completely separated, this commit doesn't
implement that yet. Instead, the static VIC stream ID is programmed when
the Falcon is booted. This ensures that memory accesses by the Falcon or
the VIC are properly translated via the SMMU.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Upon driver failure, the driver core will take care of clearing the
driver data, so there's no need to do so explicitly in the driver.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tegra186 and later, the ARM SMMU provides an input address space that
is 48 bits wide. However, memory clients can only address up to 40 bits.
If the geometry is used as-is, allocations of IOVA space can end up in a
region that cannot be addressed by the memory clients.
To fix this, restrict the IOVA space to the DMA mask of the host1x
device. Note that, technically, the IOVA space needs to be restricted to
the intersection of the DMA masks for all clients that are attached to
the IOMMU domain. In practice using the DMA mask of the host1x device is
sufficient because all host1x clients share the same DMA mask.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move initialization of the shared IOMMU domain after the host1x device
has been initialized. At this point all the Tegra DRM clients have been
attached to the shared IOMMU domain.
This is important because Tegra186 and later use an ARM SMMU, for which
the driver defers setting up the geometry for a domain until a device is
attached to it. This is to ensure that the domain is properly set up for
a specific ARM SMMU instance, which is unknown at allocation time.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Loading the firmware requires an allocation of IOVA space to make sure
that the VIC's Falcon microcontroller can read the firmware if address
translation via the SMMU is enabled.
However, the allocation currently happens at a time where the geometry
of an IOMMU domain may not have been initialized yet. This happens for
example on Tegra186 and later where an ARM SMMU is used. Domains which
are created by the ARM SMMU driver postpone the geometry setup until a
device is attached to the domain. This is because IOMMU domains aren't
attached to a specific IOMMU instance at allocation time and hence the
input address space, which defines the geometry, is not known yet.
Work around this by postponing the firmware load until it is needed at
the time where a channel is opened to the VIC. At this time the shared
IOMMU domain's geometry has been properly initialized.
As a byproduct this allows the Tegra DRM to be created in the absence
of VIC firmware, since the VIC initialization no longer fails if the
firmware can't be found.
Based on an earlier patch by Dmitry Osipenko <digetx@gmail.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tegra DRM clients need access to their parent, so store a pointer to it
upon registration. It's technically possible to get at this by going via
the host1x client's parent and getting the driver data, but that's quite
complicated and not very transparent. It's much more straightforward and
natural to let the children know about their parent.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Both macros evaluate to 0. At the same time flag is already set to
zero since the struct is kzalloc'd in framebuffer_alloc().
As called by drm_fb_helper_alloc_fbi() in the DRM drivers.
v2: Rebase and improve commit message per Emil's suggestion.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Alexander Kapshuk <alexander.kapshuk@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-tegra@vger.kernel.org
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190124165831.16427-27-daniel.vetter@ffwll.ch
Having the probe helper stuff (which pretty much everyone needs) in
the drm_crtc_helper.h file (which atomic drivers should never need) is
confusing. Split them out.
To make sure I actually achieved the goal here I went through all
drivers. And indeed, all atomic drivers are now free of
drm_crtc_helper.h includes.
v2: Make it compile. There was so much compile fail on arm drivers
that I figured I'll better not include any of the acks on v1.
v3: Massive rebase because i915 has lost a lot of drmP.h includes, but
not all: Through drm_crtc_helper.h > drm_modeset_helper.h -> drmP.h
there was still one, which this patch largely removes. Which means
rolling out lots more includes all over.
This will also conflict with ongoing drmP.h cleanup by others I
expect.
v3: Rebase on top of atomic bochs.
v4: Review from Laurent for bridge/rcar/omap/shmob/core bits:
- (re)move some of the added includes, use the better include files in
other places (all suggested from Laurent adopted unchanged).
- sort alphabetically
v5: Actually try to sort them, and while at it, sort all the ones I
touch.
v6: Rebase onto i915 changes.
v7: Rebase once more.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Acked-by: CK Hu <ck.hu@mediatek.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: virtualization@lists.linux-foundation.org
Cc: etnaviv@lists.freedesktop.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: spice-devel@lists.freedesktop.org
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-tegra@vger.kernel.org
Cc: xen-devel@lists.xen.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190117210334.13234-1-daniel.vetter@ffwll.ch
The audio setting implementation was limited to a few specific pixel
clocks. This prevented HDMI audio from working on several test devices
as they need a pixel clock that is not supported by this implementation.
Fix this by implementing the algorithm provided in the TRM using fixed
point arithmetic. This allows the driver to cope with any sane pixel
clock rate.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
[treding@nvidia.com: fix uninitialized variable warning]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The HDA format data passed to the SOR from the HDA codec contains more
information than just the rate and number of channels. Parse all the
fields and store them in an internal structure for subsequent use.
While at it, also fix an off-by-one error in the number of channels.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Most of the CEC support code already lives in the "output" library code.
Move registration and unregistration to the library code as well to make
use of the same code with HDMI on Tegra210 and later via the SOR.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Thierry Reding <treding@nvidia.com>
drm-next has been forwarded to 5.0-rc1, and we need it to apply the damage
helper for dirtyfb series from Noralf Trønnes.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Make life easier for drivers by simply passing the connector
to drm_hdmi_avi_infoframe_from_display_mode() and
drm_hdmi_avi_infoframe_quant_range(). That way drivers don't
need to worry about is_hdmi2_sink mess.
v2: Make is_hdmi2_sink() return true for sil-sii8620
Adapt to omap/vc4 changes
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108172828.15184-1-ville.syrjala@linux.intel.com
UAPI Changes:
Cross-subsystem Changes:
- Turn dma-buf fence sequence numbers into 64 bit numbers
Core Changes:
- Move to a common helper for the DP MST hotplug for radeon, i915 and
amdgpu
- i2c improvements for drm_dp_mst
- Removal of drm_syncobj_cb
- Introduction of an helper to create and attach the TV margin properties
Driver Changes:
- Improve cache flushes for v3d
- Reflection support for vc4
- HDMI overscan support for vc4
- Add implicit fencing support for rockchip and sun4i
- Switch to generic fbdev emulation for virtio
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXDOTqAAKCRDj7w1vZxhR
xZ8QAQD4j8m9Ea3bzY5Rr8BYUx1k+Cjj6Y6abZmot2rSvdyOHwD+JzJFIFAPZjdd
uOKhLnDlubaaoa6OGPDQShjl9p3gyQE=
=WQGO
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-01-07-1' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.1:
UAPI Changes:
Cross-subsystem Changes:
- Turn dma-buf fence sequence numbers into 64 bit numbers
Core Changes:
- Move to a common helper for the DP MST hotplug for radeon, i915 and
amdgpu
- i2c improvements for drm_dp_mst
- Removal of drm_syncobj_cb
- Introduction of an helper to create and attach the TV margin properties
Driver Changes:
- Improve cache flushes for v3d
- Reflection support for vc4
- HDMI overscan support for vc4
- Add implicit fencing support for rockchip and sun4i
- Switch to generic fbdev emulation for virtio
Signed-off-by: Dave Airlie <airlied@redhat.com>
[airlied: applied amdgpu merge fixup]
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190107180333.amklwycudbsub3s5@flea
If the SOR is already up and running when the kernel driver is probed,
setting a mode will typically fail. This can be seen for example on
Jetson TX2. Under certain circumstances the generic power domain code
will cause the SOR to be reset. However, if the power domain is never
powered off (this can happen if the HDA controller is enabled, which
is part of the same power domain as the SOR), then the SOR will end up
not getting reset and fail to properly set a mode.
To work around this, try to get the reset control and assert/deassert
it, irrespective of whether or not a generic power domain is attached
to the SOR. On platforms where the kernel implements generic power
domains (up to Tegra210) this will fail, because the power domain will
already have acquired an exclusive reference to the reset control. But
on recent platforms there the BPMP provides an ABI to control power
domains, it's possible to acquire the reset control from SOR and use
it to put the SOR into a known good state at probe time.
The proper solution for this is to make the SOR driver capable of
dealing with hardware that's already up and running (by first grace-
fully shutting it down, or perhaps by seamlessly transitioning to the
kernel driver and taking over the running display configuration). That
is fairly involved, though, so we'll go with this quickfix for now.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove the temporary workaround of storing the Tegra186 HDMI/DP I/O pad
ID in the SOR driver. The definition has long been available in the
soc/tegra/pmc.h header file.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This code is very similar to the audio over HDMI support on older chips.
Interoperation with the audio codec is done via a pair of codec scratch
registers and an interrupt that is raised at the SOR when the codec has
written those registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Display controllers that don't own any windows and which therefore
aren't currently being assigned a primary plane are not registered
as a CRTC with the DRM framework. They request neither a syncpoint
nor an interrupt because they don't use them, so avoid cleaning up
those resources.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The display architecture on Tegra186 and Tegra194 requires that there be
some valid clock on all domains before accessing any display register. A
further requirement is that in addition to the host1x, hub, disp and dsc
clocks, all the head clocks (pclk0-2 on Tegra186 or pclk0-3 on Tegra194)
must also be enabled.
Implement this logic within the display hub driver to ensure the clocks
are always enabled at the right time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Video Image Composer (VIC) generation found on Tegra194 is backwards
compatible with its predecessor found on Tegra186.
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ->alloc() callback in struct falcon_ops returns an ERR_PTR()-encoded
error code on failure, so it needs to be properly checked for, otherwise
subsequent code may dereference an invalid pointer.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra supports generic PM domains on 64-bit ARM, and if that is enabled,
the power domain code will make sure that resets are asserted and
deasserted at appropriate points in time.
If generic PM domains are not implemented, such as on 32-bit Tegra, the
resets need to be asserted and deasserted explicitly by the driver.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This contains initial Tegra194 support as well as a couple of fixes for
DMA/IOMMU integration.
-----BEGIN PGP SIGNATURE-----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=1zNu
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.20-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.20-rc1
This contains initial Tegra194 support as well as a couple of fixes for
DMA/IOMMU integration.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205051.30017-1-thierry.reding@gmail.com
All Tegra DRM devices are getting attached to an implicit IOMMU DMA
domain if CONFIG_ARM_DMA_USE_IOMMU=y. Since Tegra DRM driver manages IOMMU
by itself, the devices must be detached from the implicit domain using
arch-specific IOMMU-API. Note that this works only for arm32 and not for
arm64, which will remain broken if CONFIG_IOMMU_DMA is enabled.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch unifies the naming of DRM functions for reference counting
of struct drm_device. The resulting code is more aligned with the rest
of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180926115640.24755-1-tzimmermann@suse.de
The SOR implemented in Tegra194 is subtly different from its predecessor
found in Tegra186. Most notably some registers have been moved around so
it is no longer compatible.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The display hub integrated into Tegra194 is almost identical to the one
found on Tegra186. However, it doesn't support DSC (display stream
compression) so it isn't fully compatible.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra194 contains a fourth display controller that does not own any
windows. Therefore, we cannot currently assign a primary plane to it
which causes KMS to eventually crash. Do not register the display
controller if it owns no windows to work around this.
Note that we still have to enable and probe the display controller
because for some reason all display controllers need to be powered
(and/or clocked) before any registers can be accessed in any of the
display controllers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some of definitions in the code changed the meaning, unfortunately one
place missed the change.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
convert drm_atomic_helper_suspend/resume() to use
drm_mode_config_helper_suspend/resume().
With this conversion, tegra_drm_fb_suspend() and
tegra_drm_fb_resume() will not be used anymore.
Both of these functions can be removed.
Also, in tegra_drm struct's member state will not be
used anymore. So this can be removed forever.
Fixed one sparse warning.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Ajit Negi <ajitn.linux@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
-----BEGIN PGP SIGNATURE-----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=g9rD
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2018-08-15' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.19.
Rob has some new hardware support for new qualcomm hw that I'll send
along separately. This has the display part of it, the remaining pull
is for the acceleration engine.
This also contains a wound-wait/wait-die mutex rework, Peter has acked
it for merging via my tree.
Otherwise mostly the usual level of activity. Summary:
core:
- Wound-wait/wait-die mutex rework
- Add writeback connector type
- Add "content type" property for HDMI
- Move GEM bo to drm_framebuffer
- Initial gpu scheduler documentation
- GPU scheduler fixes for dying processes
- Console deferred fbcon takeover support
- Displayport support for CEC tunneling over AUX
panel:
- otm8009a panel driver fixes
- Innolux TV123WAM and G070Y2-L01 panel driver
- Ilitek ILI9881c panel driver
- Rocktech RK070ER9427 LCD
- EDT ETM0700G0EDH6 and EDT ETM0700G0BDH6
- DLC DLC0700YZG-1
- BOE HV070WSA-100
- newhaven, nhd-4.3-480272ef-atxl LCD
- DataImage SCF0700C48GGU18
- Sharp LQ035Q7DB03
- p079zca: Refactor to support multiple panels
tinydrm:
- ILI9341 display panel
New driver:
- vkms - virtual kms driver to testing.
i915:
- Icelake:
Display enablement
DSI support
IRQ support
Powerwell support
- GPU reset fixes and improvements
- Full ppgtt support refactoring
- PSR fixes and improvements
- Execlist improvments
- GuC related fixes
amdgpu:
- Initial amdgpu documentation
- JPEG engine support on VCN
- CIK uses powerplay by default
- Move to using core PCIE functionality for gens/lanes
- DC/Powerplay interface rework
- Stutter mode support for RV
- Vega12 Powerplay updates
- GFXOFF fixes
- GPUVM fault debugging
- Vega12 GFXOFF
- DC improvements
- DC i2c/aux changes
- UVD 7.2 fixes
- Powerplay fixes for Polaris12, CZ/ST
- command submission bo_list fixes
amdkfd:
- Raven support
- Power management fixes
udl:
- Cleanups and fixes
nouveau:
- misc fixes and cleanups.
msm:
- DPU1 support display controller in sdm845
- GPU coredump support.
vmwgfx:
- Atomic modesetting validation fixes
- Support for multisample surfaces
armada:
- Atomic modesetting support completed.
exynos:
- IPPv2 fixes
- Move g2d to component framework
- Suspend/resume support cleanups
- Driver cleanups
imx:
- CSI configuration improvements
- Driver cleanups
- Use atomic suspend/resume helpers
- ipu-v3 V4L2 XRGB32/XBGR32 support
pl111:
- Add Nomadik LCDC variant
v3d:
- GPU scheduler jobs management
sun4i:
- R40 display engine support
- TCON TOP driver
mediatek:
- MT2712 SoC support
rockchip:
- vop fixes
omapdrm:
- Workaround for DRA7 errata i932
- Fix mm_list locking
mali-dp:
- Writeback implementation
PM improvements
- Internal error reporting debugfs
tilcdc:
- Single fix for deferred probing
hdlcd:
- Teardown fixes
tda998x:
- Converted to a bridge driver.
etnaviv:
- Misc fixes"
* tag 'drm-next-2018-08-15' of git://anongit.freedesktop.org/drm/drm: (1506 commits)
drm/amdgpu/sriov: give 8s for recover vram under RUNTIME
drm/scheduler: fix param documentation
drm/i2c: tda998x: correct PLL divider calculation
drm/i2c: tda998x: get rid of private fill_modes function
drm/i2c: tda998x: move mode_valid() to bridge
drm/i2c: tda998x: register bridge outside of component helper
drm/i2c: tda998x: cleanup from previous changes
drm/i2c: tda998x: allocate tda998x_priv inside tda998x_create()
drm/i2c: tda998x: convert to bridge driver
drm/scheduler: fix timeout worker setup for out of order job completions
drm/amd/display: display connected to dp-1 does not light up
drm/amd/display: update clk for various HDMI color depths
drm/amd/display: program display clock on cache match
drm/amd/display: Add NULL check for enabling dp ss
drm/amd/display: add vbios table check for enabling dp ss
drm/amd/display: Don't share clk source between DP and HDMI
drm/amd/display: Fix DP HBR2 Eye Diagram Pattern on Carrizo
drm/amd/display: Use calculated disp_clk_khz value for dce110
drm/amd/display: Implement custom degamma lut on dcn
drm/amd/display: Destroy aux_engines only once
...
Merge changes in the PM core, system-wide PM infrastructure, generic
power domains (genpd) framework, ACPI PM infrastructure and cpuidle
for 4.19.
* pm-core:
driver core: Add flag to autoremove device link on supplier unbind
driver core: Rename flag AUTOREMOVE to AUTOREMOVE_CONSUMER
* pm-domains:
PM / Domains: Introduce dev_pm_domain_attach_by_name()
PM / Domains: Introduce option to attach a device by name to genpd
PM / Domains: dt: Add a power-domain-names property
* pm-sleep:
PM / reboot: Eliminate race between reboot and suspend
PM / hibernate: Mark expected switch fall-through
x86/power/hibernate_64: Remove VLA usage
PM / hibernate: cast PAGE_SIZE to int when comparing with error code
* acpi-pm:
ACPI / PM: save NVS memory for ASUS 1025C laptop
ACPI / PM: Default to s2idle in all machines supporting LP S0
* pm-cpuidle:
ARM: cpuidle: silence error on driver registration failure
Right now, the DRM panel logic returns NULL when a panel pointing to
the passed OF node is not present in the list of registered panels.
Most drivers interpret this NULL value as -EPROBE_DEFER, but we are
about to modify the semantic of of_drm_find_panel() and let the
framework return -ENODEV when the device node we're pointing to has
a status property that is not equal to "okay" or "ok".
Let's first patch the of_drm_find_panel() implementation to return
ERR_PTR(-EPROBE_DEFER) instead of NULL and patch all callers to replace
the '!panel' check by an 'IS_ERR(panel)' one.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180509130042.9435-2-boris.brezillon@bootlin.com
Now that we want to add another flag to autoremove the device link
on supplier unbind, it's fair to rename the existing flag from
DL_FLAG_AUTOREMOVE to DL_FLAG_AUTOREMOVE_CONSUMER so that we can
add similar flag for supplier later.
And, while we are touching device.h, fix a doc build warning.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here we are checking for the buffer length, not an offset for writing
to, so using > is correct. The current code incorrectly rejects a
command buffer ending at the memory buffer's end.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
We got a few conflicts in drm_atomic.c after merging the DRM writeback support,
now we need a backmerge to unlock develop development on drm-misc-next.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Neither used nor correctly implemented anywhere. Just completely remove
the interface.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://patchwork.freedesktop.org/patch/226645/
This set enables IOMMU support in the gr2d and gr3d drivers and adds
support for the zpos property on older Tegra generations. It also
enables scaling filters and incorporates some rework to eliminate a
private wrapper around struct drm_framebuffer.
The remainder is mostly a random assortment of fixes and cleanups, as
well as some preparatory work for destaging the userspace ABI, which
is almost ready and is targetted for v4.19-rc1.
-----BEGIN PGP SIGNATURE-----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=IKwO
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.18-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.18-rc1
This set enables IOMMU support in the gr2d and gr3d drivers and adds
support for the zpos property on older Tegra generations. It also
enables scaling filters and incorporates some rework to eliminate a
private wrapper around struct drm_framebuffer.
The remainder is mostly a random assortment of fixes and cleanups, as
well as some preparatory work for destaging the userspace ABI, which
is almost ready and is targetted for v4.19-rc1.
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Sat 19 May 2018 08:31:00 AEST
# gpg: using RSA key DD23ACD77F3EB3A1
# gpg: Can't check signature: public key not found
Link: https://patchwork.freedesktop.org/patch/msgid/20180518224523.30982-1-thierry.reding@gmail.com
Set the interface version implemented by the VIC module. This allows
userspace to pass the correct command stream when programming the VIC
module.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Set the interface version implemented by the gr3d module. This allows
userspace to pass the correct command stream when programming the gr3d
module.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Set the interface version implemented by the gr2d module. This allows
userspace to pass the correct command stream when programming the gr2d
module.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Userspace needs to know the version of the interface implemented by a
client so it can create the proper command streams. Allow individual
drivers to store this version along with the client so that it can be
returned to userspace upon opening a channel.
Acked-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently only the DRM_MODE_REFLECT_Y rotation is supported. The driver
already supports reflection on the Y axis via a custom flag which is not
very useful because it requires custom userspace. Add the standard
rotation property that supports 0 degree rotation and Y axis reflection
for primary and overlay planes to provide a better interface than the
custom flag.
v2: keep custom flag for ABI compatibility (Dmitry)
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Set the owner and name of the exported DMA-BUF in addition to the
already filled-in fields.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
All other array variables use a plural, and this is the only one using
the *array suffix. This is confusing, so rename it for consistency.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rather than storing some identifier derived from the application
context that can't be used concretely anywhere, store a pointer to the
client directly so that accesses can be made directly through that
client object.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The job submission userspace ABI doesn't support this and there are no
plans to implement it, so all of this code is dead and can be removed.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Now that our destroy function is the same as the helper, use that
directly.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
User framebuffers are created with either bo->pages or bo->vaddr set,
depending on whether or not an IOMMU is present. On the other hand, the
framebuffer created for fbdev emulation has a vaddr mapping made if
bo->pages is set after creation. This is set up in fbdev probe.
Remove the special case unmapping from the general-purpose framebuffer
destroy, and move it to fbdev teardown.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since tegra_fb is now the same as drm_framebuffer, we can just replace
the type completely.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since drm_framebuffer can now store GEM objects directly, place them
there rather than in our own subclass. As this makes the framebuffer
create_handle function the same as the GEM framebuffer helper, we
can reuse that.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use new return type vm_fault_t for fault handler. For now, this is just
documenting that the function returns a VM_FAULT value rather than an
errno. Once all instances are converted, vm_fault_t will become a
distinct type.
Reference id -> 1c8f422059 ("mm: change return type to vm_fault_t")
Previously vm_insert_page() returns err which driver mapped into
VM_FAULT_* type. The new function vmf_insert_page() will replace this
inefficiency by returning VM_FAULT_* type.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The IOVA API uses a memory cache to allocate IOVA nodes from. To make
sure that this cache is available, obtain a reference to it and release
the reference when the cache is no longer needed.
On 64-bit ARM this is hidden by the fact that the DMA mapping API gets
that reference and never releases it. On 32-bit ARM, however, the DMA
mapping API doesn't do that, so allocation of IOVA nodes fails.
Fixes: ad92601521 ("drm/tegra: Add Tegra DRM allocation API")
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The original code works fine, this is merely a cosmetic change to make
the teardown order the reverse of the setup order.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Older Tegra chips do support blending as well. Rename the SoC info entry
.supports_blending to .has_legacy_blending to eliminate the confusion.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Older Tegra's do not support plane's Z position handling in hardware,
but the hardware provides knobs to implement it in software.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently resized plane produces a "pixelated" image which doesn't look
nice, especially in a case of a video overlay. Enable scaling filters that
significantly improve image quality of a scaled overlay.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Attaching to and detaching from an IOMMU uses the same code sequence in
every driver, so factor it out into separate helpers.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Failure to register the Tegra DRM client would leak the resources. Move
cleanup code to error unwinding gotos to fix that and share the cleanup
code with the other error paths.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Failure to register the Tegra DRM client would leak the resources. Move
cleanup code to error unwinding gotos to fix that and share the cleanup
code with the other error paths.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If an error happens during display controller initialization, the host1x
syncpoint previously requested would be leaked. Properly clean up the
syncpoint along with the other resources.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Attach GR3D to the displays IOMMU group in order to provide GR3D access
to BO's IOVA.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Attach GR2D to the display IOMMU group in order to provide GR2D access
to BO's IOVA.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove unneeded iommu_group_get() and add missing iommu_group_put(),
correcting IOMMU group refcount. This is a minor correction / cleanup that
doesn't really fix anything because Tegra's IOMMU driver are built-in and
hence groups refcounting can't hold IOMMU driver from unloading.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Using drm_atomic_get_private_obj_state() after state has been swapped
will return old state.
Fixes: 0281c41490 ("drm/tegra: hub: Use private object for global state")
Signed-off-by: Stefan Schake <stschake@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
UAPI Changes:
- Add support for a generic plane alpha property to sun4i, rcar-du and atmel-hclcdc. (Maxime)
Core Changes:
- Stop looking at legacy plane->fb and crtc members in atomic drivers. (Ville)
- mode_valid return type fixes. (Luc)
- Handle zpos normalization in the core. (Peter)
Driver Changes:
- Implement CTM, plane alpha and generic async cursor support in vc4. (Stefan)
- Various fixes for HPD and aux chan in drm_bridge/analogix_dp. (Lin, Zain, Douglas)
- Add support for MIPI DSI to sun4i. (Maxime)
-----BEGIN PGP SIGNATURE-----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=9LYY
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-04-26' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v4.18:
UAPI Changes:
- Add support for a generic plane alpha property to sun4i, rcar-du and atmel-hclcdc. (Maxime)
Core Changes:
- Stop looking at legacy plane->fb and crtc members in atomic drivers. (Ville)
- mode_valid return type fixes. (Luc)
- Handle zpos normalization in the core. (Peter)
Driver Changes:
- Implement CTM, plane alpha and generic async cursor support in vc4. (Stefan)
- Various fixes for HPD and aux chan in drm_bridge/analogix_dp. (Lin, Zain, Douglas)
- Add support for MIPI DSI to sun4i. (Maxime)
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Thu 26 Apr 2018 08:21:01 PM AEST
# gpg: using RSA key FE558C72A67013C3
# gpg: Can't check signature: public key not found
Link: https://patchwork.freedesktop.org/patch/msgid/b33da7eb-efc9-ae6f-6f69-b7acd6df6797@mblankhorst.nl
-----BEGIN PGP SIGNATURE-----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=DrA+
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.17' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"Cannonlake and Vega12 support are probably the two major things. This
pull lacks nouveau, Ben had some unforseen leave and a few other
blockers so we'll see how things look or maybe leave it for this merge
window.
core:
- Device links to handle sound/gpu pm dependency
- Color encoding/range properties
- Plane clipping into plane check helper
- Backlight helpers
- DP TP4 + HBR3 helper support
amdgpu:
- Vega12 support
- Enable DC by default on all supported GPUs
- Powerplay restructuring and cleanup
- DC bandwidth calc updates
- DC backlight on pre-DCE11
- TTM backing store dropping support
- SR-IOV fixes
- Adding "wattman" like functionality
- DC crc support
- Improved DC dual-link handling
amdkfd:
- GPUVM support for dGPU
- KFD events for dGPU
- Enable PCIe atomics for dGPUs
- HSA process eviction support
- Live-lock fixes for process eviction
- VM page table allocation fix for large-bar systems
panel:
- Raydium RM68200
- AUO G104SN02 V2
- KEO TX31D200VM0BAA
- ARM Versatile panels
i915:
- Cannonlake support enabled
- AUX-F port support added
- Icelake base enabling until internal milestone of forcewake support
- Query uAPI interface (used for GPU topology information currently)
- Compressed framebuffer support for sprites
- kmem cache shrinking when GPU is idle
- Avoid boosting GPU when waited item is being processed already
- Avoid retraining LSPCON link unnecessarily
- Decrease request signaling latency
- Deprecation of I915_SET_COLORKEY_NONE
- Kerneldoc and compiler warning cleanup for upcoming CI enforcements
- Full range ycbcr toggling
- HDCP support
i915/gvt:
- Big refactor for shadow ppgtt
- KBL context save/restore via LRI cmd (Weinan)
- Properly unmap dma for guest page (Changbin)
vmwgfx:
- Lots of various improvements
etnaviv:
- Use the drm gpu scheduler
- prep work for GC7000L support
vc4:
- fix alpha blending
- Expose perf counters to userspace
pl111:
- Bandwidth checking/limiting
- Versatile panel support
sun4i:
- A83T HDMI support
- A80 support
- YUV plane support
- H3/H5 HDMI support
omapdrm:
- HPD support for DVI connector
- remove lots of static variables
msm:
- DSI updates from 10nm / SDM845
- fix for race condition with a3xx/a4xx fence completion irq
- some refactoring/prep work for eventual a6xx support (ie. when we
have a userspace)
- a5xx debugfs enhancements
- some mdp5 fixes/cleanups to prepare for eventually merging
writeback
- support (ie. when we have a userspace)
tegra:
- mmap() fixes for fbdev devices
- Overlay plane for hw cursor fix
- dma-buf cache maintenance support
mali-dp:
- YUV->RGB conversion support
rockchip:
- rk3399/chromebook fixes and improvements
rcar-du:
- LVDS support move to drm bridge
- DT bindings for R8A77995
- Driver/DT support for R8A77970
tilcdc:
- DRM panel support"
* tag 'drm-for-v4.17' of git://people.freedesktop.org/~airlied/linux: (1646 commits)
drm/i915: Fix hibernation with ACPI S0 target state
drm/i915/execlists: Use a locked clear_bit() for synchronisation with interrupt
drm/i915: Specify which engines to reset following semaphore/event lockups
drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.
drm/amdkfd: Use ordered workqueue to restore processes
drm/amdgpu: Fix acquiring VM on large-BAR systems
drm/amd/pp: clean header file hwmgr.h
drm/amd/pp: use mlck_table.count for array loop index limit
drm: Fix uabi regression by allowing garbage mode->type from userspace
drm/amdgpu: Add an ATPX quirk for hybrid laptop
drm/amdgpu: fix spelling mistake: "asssert" -> "assert"
drm/amd/pp: Add new asic support in pp_psm.c
drm/amd/pp: Clean up powerplay code on Vega12
drm/amd/pp: Add smu irq handlers for legacy asics
drm/amd/pp: Fix set wrong temperature range on smu7
drm/amdgpu: Don't change preferred domian when fallback GTT v5
drm/vmwgfx: Bump version patchlevel and date
drm/vmwgfx: use monotonic event timestamps
drm/vmwgfx: Unpin the screen object backup buffer when not used
drm/vmwgfx: Stricter count of legacy surface device resources
...
Set the drm_mode_config->normalize_zpos and call the generic
drm_atomic_helper_check() instead of duplicating it within
tegra_atomic_check().
Call tegra_display_hub_atomic_check() after the drm_atomic_helpre_check()
returned without error.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180321102029.15248-4-peter.ujfalusi@ti.com
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJauCZfAAoJEHm+PkMAQRiGWGUH/2rhdQDkoJpYWnjaQkolECG8
MxpGE7nmIIHxQcbSDdHTGJ8IhVm6Z5wZ7ym/PwCDTT043Y1y341sJrIwL2/nTG6d
HVidk8hFvgN6QzlzVAHT3ZZMII/V9Zt+VV5SUYLGnPAVuJNHo/6uzWlTU5g+NTFo
IquFDdQUaGBlkKqby+NoAFnkV1UAIkW0g22cfvPnlO5GMer0gusGyVNvVp7TNj3C
sqj4Hvt3RMDLMNe9RZ2pFTiOD096n8FWpYftZneUTxFImhRV3Jg5MaaYZm9SI3HW
tXrv/LChT/F1mi5Pkx6tkT5Hr8WvcrwDMJ4It1kom10RqWAgjxIR3CMm448ileY=
=YKUG
-----END PGP SIGNATURE-----
Backmerge tag 'v4.16-rc7' into drm-next
Linux 4.16-rc7
This was requested by Daniel, and things were getting
a bit hard to reconcile, most of the conflicts were
trivial though.
Use tegra124_(primary|overlay)_formats for Tegra124, otherwise the count
specified in the Tegra124 SoC info structure will be different from the
array size and cause a crash.
Fixes: 511c7023cf ("drm/tegra: dc: Support more formats")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This fixes mmap() for fbdev devices by providing a custom implementation
based on the KMS variant. This is a fairly exotic case these days, hence
why it is not flagged for stable.
There is also support for dedicating one of the overlay planes to serve
as a hardware cursor on older Tegra that did support hardware cursors
but not RGBA formats for it.
Planes will now also export the IN_FORMATS property by supporting the
various block-linear tiling modifiers for RGBA pixel formats.
Other than that, there's a bit of cleanup of DMA API abuse, use of the
private object infrastructure for global state (rather than subclassing
atomic state objects) and an implementation of ->{begin,end}_cpu_access
callbacks for PRIME exported buffers, which allow users to perform cache
maintenance on these buffers.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAlqviKkTHHRyZWRpbmdA
bnZpZGlhLmNvbQAKCRDdI6zXfz6zod+zD/9p04Jmsbd30dttPqb1Dns1e4N/cXcP
hLgqYjc+Apov3ksrFS7bhlmIKxMcIXvw6s/ciwapO4tNMuWfKke6+LX7eGxyzMFn
aGm7Na0fcb+R6U7Cs8J45b9XB0NBGuz2Vv9rIne/I7BoVE1XCPfEBYgYGT6hR0cj
fPWKAldD1CVJXJX48mIsgUe8w8PHBijN0qEfrNTmQTA/zZ4PeZQpdoilLS8lsb74
fg9BWaTHYLchHFaLShsuSJwS/qHCMLCMv01dhCV5OlpaZWXki4iqhjuIuHeZnk3c
ygWcmjDkE4Aaihq5mcPD1tYe8D223TW3XbtHDsl1MKVLdHliSSp3xsWlbqB42BiK
QtXNhmEUbx4cnvNA6e/5wXTZImNHRJnkcAIMro7z5Vq3Xav+4bcPiLROd9nz28GS
WNuAoV26YedWtK9taJEAoO6Nas6K+f2jQKcph97Rrii+LwkZqNLeHzikTXcIAwDF
M55wIcLRt1b2a3ZPxWOE3sl0gTyMdJbITt5t2zyl3OXCnGINmSCn6Bfm8EZsFY+j
2J8v25T6VTQC5MWyR75abppMvdqk4ihIWSmIH4vdlpj202dD5q9T+CWaLCguxZPY
racx4bDUEJB9Gt5iJAQNVq8alDhioynygXwGbVuPY7BAiBKQWNyHBbgRWBAPGjXR
CnGh3KfFFEFWkA==
=gOLI
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.17-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.17-rc1
This fixes mmap() for fbdev devices by providing a custom implementation
based on the KMS variant. This is a fairly exotic case these days, hence
why it is not flagged for stable.
There is also support for dedicating one of the overlay planes to serve
as a hardware cursor on older Tegra that did support hardware cursors
but not RGBA formats for it.
Planes will now also export the IN_FORMATS property by supporting the
various block-linear tiling modifiers for RGBA pixel formats.
Other than that, there's a bit of cleanup of DMA API abuse, use of the
private object infrastructure for global state (rather than subclassing
atomic state objects) and an implementation of ->{begin,end}_cpu_access
callbacks for PRIME exported buffers, which allow users to perform cache
maintenance on these buffers.
* tag 'drm/tegra/for-4.17-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: prime: Implement ->{begin,end}_cpu_access()
drm/tegra: gem: Map pages via the DMA API
drm/tegra: hub: Use private object for global state
drm/tegra: fb: Properly support linear modifier
drm/tegra: plane: Support format modifiers
drm/tegra: dc: Dedicate overlay plane to cursor on older Tegra's
drm/tegra: plane: Make tegra_plane_get_overlap_index() static
drm/tegra: fb: Implement ->fb_mmap() callback
drm/tegra: gem: Make __tegra_gem_mmap() available more widely
drm/tegra: gem: Reshuffle declarations
Since commit 846c7dfc11 ("drm/atomic: Try to preserve the crtc enabled
state in drm_atomic_remove_fb, v2."), removing the last framebuffer will
no longer disable the corresponding pipeline, which causes the KMS core
to complain about leaked connectors on driver unbind.
Fix this by calling drm_atomic_helper_shutdown() on driver unbind, which
will cause all display pipelines to be shut down and therefore drop the
extra references on the connectors.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The regulator is controlled as part of runtime PM, so it should not be
additionally disabled from the ->exit() callback.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Detaching from an IOMMU group multiple times can lead to a crash. This
could potentially be fixed in the IOMMU driver, but it's easy to avoid
the subsequent detach operations in this driver, so do that as well.
Signed-off-by: Thierry Reding <treding@nvidia.com>
These callbacks allow the exporter to swap in and pin the backing
storage for buffers as well as invalidate the cache in preparation for
accessing the buffer from the CPU, and flush the cache and unpin the
backing storage when the CPU is done modifying the buffer.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When allocating pages, map them with the DMA API in order to invalidate
caches. This is the correct usage of the API and works just as well as
faking up the SG table and using the dma_sync_sg_for_device() function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rather than subclass the global atomic state to store the hub display
clock and rate, create a private object and store this data in its
state.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of relying on the tiling attached to a buffer object, make sure
to set the proper tiling for linear buffers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Pass the list of valid format modifiers to planes upon initialization
and implement the ->format_mod_supported() callback so that userspace
can query for the valid combinations of formats and modifiers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Keep old 'dependent' state of unaffected planes, this way new state takes
into account current state of unaffected planes.
Fixes: ebae8d0743 ("drm/tegra: dc: Implement legacy blending")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Older Tegra's do not support RGBA format for the cursor, but instead
overlay plane could be used for it. Since there is no much use for the
overlays on a regular desktop and HW-accelerated cursor is much better
than a SW cursor, let's dedicate one overlay plane to the mouse cursor.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This function is not used outside of the file and can be static.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The opaque/alpha format conversion code is currently only looking at
XRGB formats because they have an equivalent ARGB format. The opaque
format for RGB565 is RGB565 itself, much like the YUV formats map to
themselves.
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Fixes: ebae8d0743 ("drm/tegra: dc: Implement legacy blending")
Signed-off-by: Thierry Reding <treding@nvidia.com>
This fixes hangs with legacy applications that use the mmap() syscall on
the fbdev device to map framebuffer memory. The fbdev implementation for
mmap() creates a mapping that conflicts with DRM usage and causes a hang
when the memory is accessed through the mapping.
Reported-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Stefan Agner <stefan@agner.ch>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reported-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This function allows mapping a GEM object into a virtual memory address
space, which makes it useful outside of the GEM code.
While at it, rename the function so it doesn't clash with the function
that implements the DRM_TEGRA_GEM_MMAP IOCTL.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move declarations in the gem.h header file into the same order as the
corresponding definitions in gem.c.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Driver Changes:
- Lift alpha_support protection from Cannonlake (Rodrigo)
* Meaning the driver should mostly work for the hardware we had
at our disposal when testing
* Used to be preliminary_hw_support
- Add missing Cannonlake PCI device ID of 0x5A4C (Rodrigo)
- Cannonlake port register fix (Mahesh)
- Fix Dell Venue 8 Pro black screen after modeset (Hans)
- Fix for always returning zero out-fence from execbuf (Daniele)
- Fix HDMI audio when no no relevant video output is active (Jani)
- Fix memleak of VBT data on driver_unload (Hans)
- Fix for KASAN found locking issue (Maarten)
- RCU barrier consolidation to improve igt/gem_sync/idle (Chris)
- Optimizations to IRQ handlers (Chris)
- vblank tracking improvements (64-bit resolution, PM) (Dhinakaran)
- Pipe select bit corrections (Ville)
- Reduce runtime computed device_info fields (Chris)
- Tune down some WARN_ONs to GEM_BUG_ON now that CI has good coverage (Chris)
- A bunch of kerneldoc warning fixes (Chris)
* tag 'drm-intel-next-2018-02-21' of git://anongit.freedesktop.org/drm/drm-intel: (113 commits)
drm/i915: Update DRIVER_DATE to 20180221
drm/i915/fbc: Use PLANE_HAS_FENCE to determine if the plane is fenced
drm/i915/fbdev: Use the PLANE_HAS_FENCE flags from the time of pinning
drm/i915: Move the policy for placement of the GGTT vma into the caller
drm/i915: Also check view->type for a normal GGTT view
drm/i915: Drop WaDoubleCursorLP3Latency:ivb
drm/i915: Set the primary plane pipe select bits on gen4
drm/i915: Don't set cursor pipe select bits on g4x+
drm/i915: Assert that we don't overflow frontbuffer tracking bits
drm/i915: Track number of pending freed objects
drm/i915/: Initialise trans_min for skl_compute_transition_wm()
drm/i915: Clear the in-use marker on execbuf failure
drm/i915: Prune gen8_gt_irq_handler
drm/i915: Track GT interrupt handling using the master iir
drm/i915: Remove WARN_ONCE for failing to pm_runtime_if_in_use
drm: intel_dpio_phy: fix kernel-doc comments at nested struct
drm/i915: Release connector iterator on a digital port conflict.
drm/i915/execlists: Remove too early assert
drm/i915: Assert that we always complete a submission to guc/execlists
drm: move read_domains and write_domain into i915
...
570e86963a ("drm: Widen vblank count to 64-bits [v3]") changed the
return type for drm_crtc_vblank_count() to u64. This could cause
potential problems if the return value is used in arithmetic operations
with a 32-bit reference HW vblank count. Explicitly typecasting this
down to u32 either fixes a potential problem or serves to add clarity in
case the implicit typecasting was already correct.
Cc: Keith Packard <keithp@keithp.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203051302.9974-6-dhinakaran.pandiyan@intel.com
Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.
No functional changes as the code already uses crtc_state->mode
to populate the clip, which is also what drm_mode_get_hv_timing()
uses.
Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().
v2: Rebase due to tegra_plane_state_add() relocating to plane.c
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-13-ville.syrjala@linux.intel.com
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaW+iVAAoJEHm+PkMAQRiGCDsIAJALNpX7odTx/8y+yCSWbpBH
E57iwr4rmnI6tXJY6gqBUWTYnjAcf4b8IsHGCO6q3WIE3l/kt+m3eA21a32mF2Db
/bfPGTOWu5LoOnFqzgH2kiFuC3Y474toxpld2YtkQWYxi5W7SUtIHi/jGgkUprth
g15yPfwYgotJd/gpmPfBDMPlYDYvLlnPYbTG6ZWdMbg39m2RF2m0BdQ6aBFLHvbJ
IN0tjCM6hrLFBP0+6Zn60pevUW9/AFYotZn2ankNTk5QVCQm14rgQIP+Pfoa5WpE
I25r0DbkG2jKJCq+tlgIJjxHKD37GEDMc4T8/5Y8CNNeT9Q8si9EWvznjaAPazw=
=o5gx
-----END PGP SIGNATURE-----
BackMerge tag 'v4.15-rc8' into drm-next
Linux 4.15-rc8
Daniel requested this for so the intel CI won't fall over on drm-next
so often.
The bulk of these changes are preparation work and addition of support
for Tegra186. Currently only HDMI output (the primary output on Jetson
TX2) is supported, but the hardware is also capable of doing DSI and
DisplayPort.
Tegra DRM now also uses the atomic commit helpers instead of the open-
coded variant that was only doing half its job. As a bit of a byproduct
of the Tegra186 support the driver also gained HDMI 2.0 as well as zpos
property support.
Along the way there are also a few patches to clean up a few things and
fix minor issues.
-----BEGIN PGP SIGNATURE-----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=FfXI
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.16-rc1-fixes' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.16-rc1
The bulk of these changes are preparation work and addition of support
for Tegra186. Currently only HDMI output (the primary output on Jetson
TX2) is supported, but the hardware is also capable of doing DSI and
DisplayPort.
Tegra DRM now also uses the atomic commit helpers instead of the open-
coded variant that was only doing half its job. As a bit of a byproduct
of the Tegra186 support the driver also gained HDMI 2.0 as well as zpos
property support.
Along the way there are also a few patches to clean up a few things and
fix minor issues.
* tag 'drm/tegra/for-4.16-rc1-fixes' of git://anongit.freedesktop.org/tegra/linux: (51 commits)
drm/tegra: dc: Properly cleanup overlay planes
drm/tegra: dc: Fix possible_crtcs mask for planes
drm/tegra: dc: Restore YUV overlay support
drm/tegra: dc: Implement legacy blending
drm/tegra: Correct timeout in tegra_syncpt_wait
drm/tegra: gem: Correct iommu_map_sg() error checking
drm/tegra: dc: Link DC1 to DC0 on Tegra20
drm/tegra: Fix non-debugfs builds
drm/tegra: dpaux: Keep reset defaults for hybrid pad parameters
drm/tegra: Mark Tegra186 display hub PM functions __maybe_unused
drm/tegra: Use IOMMU groups
gpu: host1x: Use IOMMU groups
drm/tegra: Implement zpos property
drm/tegra: dc: Remove redundant spinlock
drm/tegra: dc: Use direct offset to plane registers
drm/tegra: dc: Support more formats
drm/tegra: fb: Force alpha formats
drm/tegra: dpaux: Add Tegra186 support
drm/tegra: dpaux: Implement runtime PM
drm/tegra: sor: Support HDMI 2.0 modes
...
The SOR0 found on Tegra124 and Tegra210 only supports eDP and LVDS and
therefore has a slightly different clock tree than the SOR1 which does
not support eDP, but HDMI and DP instead.
Commit e1335e2f0c ("drm/tegra: sor: Reimplement pad clock") breaks
setups with eDP because the sor->clk_out clock is uninitialized and
therefore setting the parent clock (either the safe clock or either of
the display PLLs) fails, which can cause hangs later on since there is
no clock driving the module.
Fix this by falling back to the module clock for sor->clk_out on those
setups. This guarantees that the module will always be clocked by an
enabled clock and hence prevents those hangs.
Fixes: e1335e2f0c ("drm/tegra: sor: Reimplement pad clock")
Reported-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The first overlay plane can leak if initialization of the second overlay
plane fails. Fix this by properly destroying the first overlay plane on
error.
Suggested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Cursor and overlay planes use a possible_crtcs mask based on the DC pipe
number. However, DRM requires each bit in the mask to correspond to the
index of the CRTC, which will be different from the DC pipe number for a
configuration where the first display controller is disabled, or where a
deferred probe leads to the first display controller being probed after
the first.
Suggested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit ebae8d0743 ("drm/tegra: dc: Implement legacy blending") broke
support for YUV overlays by accident. The reason is that YUV formats are
considered opaque because they have no alpha component, but on the other
hand no corresponding format with an alpha component can be returned. In
the case of YUV formats, the opaque format is the same as the alpha
format, so add the special case to restore YUV overlay support.
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This implements alpha blending on legacy display controllers (Tegra20,
Tegra30 and Tegra114). While it's theoretically possible to support the
zpos property to enable userspace to specify the Z-order of each plane
individually, this is not currently supported and the same fixed Z-
order as previously defined is used.
Reverts commit 71835caa00 ("drm/tegra: fb: Force alpha formats") since
the opaque formats are now supported.
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Fixes: 7772fdaef9 ("drm/tegra: Support ARGB and ABGR formats")
Signed-off-by: Thierry Reding <treding@nvidia.com>
host1x_syncpt_wait() takes timeout value in jiffies, but DRM passes it in
milliseconds.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
iommu_map_sg() doesn't return a error value, but a size of the requested
IOMMU mapping or zero in case of error.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Hardware reset isn't actually broken on Tegra20, but there is a
dependency on the first display controller to be taken out of reset for
the second to be enabled successfully. Model this dependency using a PM
device link.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
[treding@nvidia.com: minor cleanups, extend commit message]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The new debugfs registration fails to build when CONFIG_DEBUGFS is
disabled, because the drm_crtc structure is lacking a member in that
configuration:
drivers/gpu/drm/tegra/dc.c: In function 'tegra_dc_late_register':
drivers/gpu/drm/tegra/dc.c:1204:28: error: 'struct drm_crtc' has no member named 'debugfs_entry'
Without CONFIG_DEBUGFS, the rest of the function already degrades
into nothing, so we just avoid the one assignment.
Fixes: b95800eeef ("drm/tegra: dc: Register debugfs in ->late_register()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Keep the reset values for the common mode voltage, output driver
impedance control and output driver current control parameters. This
fixes errors seen during SCDC communication with HDMI sinks.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The newly introduced driver has optional suspend/resume functions,
causing a warning when CONFIG_PM is disabled:
drivers/gpu/drm/tegra/hub.c:749:12: error: 'tegra_display_hub_resume' defined but not used [-Werror=unused-function]
drivers/gpu/drm/tegra/hub.c:733:12: error: 'tegra_display_hub_suspend' defined but not used [-Werror=unused-function]
This marks them __maybe_unused to shut up the warnings.
Fixes: c4755fb906 ("drm/tegra: Add Tegra186 display hub support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to support IOMMUs more generically and transparently handle the
ARM SMMU on Tegra186, move to using groups instead of devices for domain
attachment. An IOMMU group is a set of devices that share the same IOMMU
domain and is therefore a good match to represent what Tegra DRM needs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement the standard zpos property for planes on Tegra124 and later.
Earlier generations have a different blending unit that needs different
programming.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The spinlock is only used to serialize accesses to the DC_CMD_INT_MASK
register. However, this register is accesses either with interrupts
masked (in tegra_crtc_atomic_enable()) or protected by the vbl_lock and
vblank_time_lock spinlocks of the DRM device. Therefore, these accesses
don't need any extra serialization and the lock can be removed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Traditionally, windows were accessed indirectly, through a register
selection window that required a global register to be programmed with
the index of the window to access. Since the global register could be
written from modesetting functions as well as the interrupt handler
concurrently, accesses had to be serialized using a lock. Using direct
accesses to the window registers the lock can be avoided.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Also, split up formats into per-SoC lists because not all generations
support all of them. Note that the list is now exhaustive for all RGB
formats, but not for YUV and indexed formats.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra20 and Tegra30 don't actually support the 24-bit RGB formats that
don't have an alpha component. In order to allow the fbdev emulation to
run on those chips, force the 32-bit RGBA formats.
Signed-off-by: Thierry Reding <treding@nvidia.com>
DPAUX is the same as on previous generations. Supporting it is as simple
as adding the compatible string so that the driver will bind to any of
the devices.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move clock and reset management into runtime PM callbacks and hook them
up. This cleans up the code structure so that power management code does
not clutter up the rest.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In addition to using the SCDC helpers to enable support for scrambling
for HDMI 2.0 modes, take into account the high pixel clocks when
programming some of the registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR found on Tegra186 is very similar to the one found on Tegra210
and earlier. However, due to some changes in the display architecture,
some programming sequences have changed and some register have moved
around.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Future Tegra generations have an increased number of display controllers
that can drive individual SORs. In order to support that, the offset and
layout of some registers has changed in backwards-incompatible ways. Use
parameterized register offsets to support this.
Signed-off-by: Thierry Reding <treding@nvidia.com>
These formats can easily be supported on all generations of Tegra.
Note that the XRGB and XBGR formats that we supported were in fact using
the ARGB and ABGR Tegra formats. This happened to work in cases where no
alpha was being considered. This change is also a fix for those formats.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The display architecture has changed in several signifcant ways with the
new Tegra186 SoC. Display controllers are a completely different design,
but have been given a frontend that simulates the register interface for
earlier chips.
Unfortunately the frontend isn't completely backwards compatible, so the
driver needs parameterization to take the changes into account.
One big change is that the total number of display controllers has been
increased to three. At the same time the number of planes available has
remained constant. However, planes can now be freely assigned between
the display controllers, giving applications more flexibility in making
the best use of the available resources.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The display architecture has changed in several significant ways with
the new Tegra186 SoC. Shared between all display controllers is a set
of common resources referred to as the display hub. The hub generates
accesses to memory and feeds them into various composition pipelines,
each of which being a window that can be assigned to arbitrary heads.
Atomic state is subclassed in order to track the global bandwidth
requirements and select and adjust the hub clocks appropriately. The
plane code is shared to a large degree with earlier SoC generations,
except where the programming differs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Subsequent patches will add support for Tegra186 which has a different
architecture and needs different plane code but which can share a lot of
code with earlier Tegra support.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move the display controller state definition to the header file so that
it can be referenced by other files.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Both tegra_overlay_plane_funcs is identical to tegra_plane_funcs. Get
rid of the duplicate and use one set of function pointers for all
planes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Both tegra_primary_plane_funcs and tegra_cursor_plane_funcs are
identical. Get rid of the duplicate and use one set of function pointers
for all planes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra display hardware has GO bits and meets all the requirements to use
drm_crtc_arm_vblank_event(). Use it instead and get rid of the hand-
rolled implementation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
There's no reason not to use them, and they already get all the
semantics right, so rip out all of the custom code and replace it by the
helpers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Starting with Tegra124, the interface to set the background color (the
value generated for pixels that are not sourced from any window) is via
a different register. Earlier generations called this the border color.
Reverse the feature flag and assume that IP revisions that don't have
support for background color will support border color instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ->late_register() and ->early_unregister() callbacks are called at
the right time to make sure userspace only accesses interfaces when it
should. Move debugfs registration and unregistration to these callback
functions to avoid potential races with userspace.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rather create new files within the top-level DRM device's debugfs node,
add the SOR specific files to the connector's debugfs node. This avoids
the need to come up with subdirectory names and is also more intuitive.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ->late_register() and ->early_unregister() callbacks are called at
the right time to make sure userspace only accesses interfaces when it
should. Move debugfs registration and unregistration to these callback
functions to avoid potential races with userspace.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ->late_register() and ->early_unregister() callbacks are called at
the right time to make sure userspace only accesses interfaces when it
should. Move debugfs registration and unregistration to these callback
functions to avoid potential races with userspace.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ->late_register() and ->early_unregister() callbacks are called at
the right time to make sure userspace only accesses interfaces when it
should. Move debugfs registration and unregistration to these callback
functions to avoid potential races with userspace.
Signed-off-by: Thierry Reding <treding@nvidia.com>
After commit 932f652913 ("drm/tegra: sor: Trace register accesses"),
the debugfs register dump implementation causes excessive stack usage
and can result in build warnings. To fix this, move the register
definitions into a table and iterate over the table while dumping the
registers to debugfs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
After commit 07a8aab899 ("drm/tegra: hdmi: Trace register accesses"),
the debugfs register dump implementation causes excessive stack usage
and can result in build warnings. To fix this, move the register
definitions into a table and iterate over the table while dumping the
registers to debugfs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
After commit 75af8fa7fd ("drm/tegra: dsi: Trace register accesses"),
the debugfs register dump implementation causes excessive stack usage
and can result in build warnings. To fix this, move the register
definitions into a table and iterate over the table while dumping the
registers to debugfs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
After commit 67e04d1ab1 ("drm/tegra: dc: Trace register accesses"),
the debugfs register dump implementation causes excessive stack usage
and can result in build warnings. To fix this, move the register
definitions into a table and iterate over the table while dumping the
registers to debugfs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The existing format modifier definitions were merged prematurely, and
recent work has unveiled that the definitions are suboptimal in several
ways:
- The format specifiers, except for one, are not Tegra specific, but
the names don't reflect that.
- The number space is split into two, reserving 32 bits for some
"parameter" which most of the modifiers are not going to have.
- Symbolic names for the modifiers are not using the standard
DRM_FORMAT_MOD_* prefix, which makes them awkward to use.
- The vendor prefix NV is somewhat ambiguous.
Fortunately, nobody's started using these modifiers, so we can still fix
the above issues. Do so by using the standard prefix. Also, remove TEGRA
from the name of those modifiers that exist on NVIDIA GPUs as well. In
case of the block linear modifiers, make the "parameter" smaller (4
bits, though only 6 values are valid) and don't let that leak into any
of the other modifiers.
Finally, also use the more canonical NVIDIA instead of the ambiguous NV
prefix.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This driver can use drm_fb_helper_lastclose() as its .lastclose callback.
It can also use drm_fb_helper_output_poll_changed() as its
.output_poll_changed callback.
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20171205182504.41923-12-noralf@tronnes.org
Cross-subsystem Changes:
- device tree doc for the Mitsubishi AA070MC01 and Tianma TM070RVHG71
panels (Lukasz Majewski) and for a 2nd endpoint on stm32 (Philippe Cornu)
Core Changes:
The most important changes are:
- Add drm_driver .last_close and .output_poll_changed helpers to reduce
fbdev emulation footprint in drivers (Noralf)
- Fix plane clipping in core and for vmwgfx (Ville)
Then we have a bunch of of improvement for print and debug such as the
addition of a framebuffer debugfs file. ELD connector, HDMI and
improvements. And a bunch of misc improvements, clean ups and style
changes and doc updates
[airlied: drop eld bits from amdgpu_dm]
Driver Changes:
- sii8620: filter unsupported modes and add DVI mode support (Maciej Purski)
- rockchip: analogix_dp: Remove unnecessary init code (Jeffy Chen)
- virtio, cirrus: add fb create_handle support to enable screenshots(Lepton Wu)
- virtio: replace reference/unreference with get/put (Aastha Gupta)
- vc4, gma500: Convert timers to use timer_setup() (Kees Cook)
- vc4: Reject HDMI modes with too high of clocks (Eric)
- vc4: Add support for more pixel formats (Dave Stevenson)
- stm: dsi: Rename driver name to "stm32-display-dsi" (Philippe Cornu)
- stm: ltdc: add a 2nd endpoint (Philippe Cornu)
- via: use monotonic time for VIA_WAIT_IRQ (Arnd Bergmann)
* tag 'drm-misc-next-2017-11-30' of git://anongit.freedesktop.org/drm/drm-misc: (96 commits)
drm/bridge: tc358767: add copyright lines
MAINTAINERS: change maintainer for Rockchip drm drivers
drm/vblank: Fix vblank timestamp debugs
drm/via: use monotonic time for VIA_WAIT_IRQ
dma-buf: Fix ifnullfree.cocci warnings
drm/printer: Add drm_vprintf()
drm/edid: Allow HDMI infoframe without VIC or S3D
video/hdmi: Allow "empty" HDMI infoframes
dma-buf/fence: Fix lock inversion within dma-fence-array
drm/sti: Handle return value of platform_get_irq_byname
drm/vc4: Add support for NV21 and NV61.
drm/vc4: Use .pixel_order instead of custom .flip_cbcr
drm/vc4: Add support for DRM_FORMAT_RGB888 and DRM_FORMAT_BGR888
drm: Move drm_plane_helper_check_state() into drm_atomic_helper.c
drm: Check crtc_state->enable rather than crtc->enabled in drm_plane_helper_check_state()
drm/vmwgfx: Try to fix plane clipping
drm/vmwgfx: Use drm_plane_helper_check_state()
drm/vmwgfx: Remove bogus crtc coords vs fb size check
gpu: gma500: remove unneeded DRIVER_LICENSE #define
drm: don't link DP aux i2c adapter to the hardware device node
...
-----BEGIN PGP SIGNATURE-----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=P4O6
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.15-part2' of git://people.freedesktop.org/~airlied/linux
Pull more drm updates from Dave Airlie:
"Fixes/cleanups for rc1, non-desktop flags for VR
- remove the MSM dt-bindings file Rob managed to push in the previous
pull.
- add a property/edid quirk to denote HMD devices, I had these
hanging around for a few weeks and Keith had done some work on
them, they are fairly self contained and small, and only affect
people using HTC Vive VR headsets so far.
- amdgpu, tegra, tilcdc, fsl fixes
- some imx-drm cleanups I missed, these seemed pretty small, and no
reason to hold off.
I have one TTM regression fix (fixes bochs-vga in qemu) sitting
locally awaiting review I'll probably send that in a separate pull
request tomorrow"
* tag 'drm-for-v4.15-part2' of git://people.freedesktop.org/~airlied/linux: (33 commits)
dt-bindings: remove file that was added accidentally
drm/edid: quirk HTC vive headset as non-desktop. [v2]
drm/fb: add support for not enabling fbcon on non-desktop displays [v2]
drm: add connector info/property for non-desktop displays [v2]
drm/amdgpu: fix rmmod KCQ disable failed error
drm/amdgpu: fix kernel hang when starting VNC server
drm/amdgpu: don't skip attributes when powerplay is enabled
drm/amd/pp: fix typecast error in powerplay.
drm/tilcdc: Remove obsolete "ti,tilcdc,slave" dts binding support
drm/tegra: sor: Reimplement pad clock
Revert "drm/radeon: dont switch vt on suspend"
drm/amd/amdgpu: fix over-bound accessing in amdgpu_cs_wait_any_fence
drm/amd/powerplay: fix unfreeze level smc message for smu7
drm/amdgpu:fix memleak
drm/amdgpu:fix memleak in takedown
drm/amd/pp: fix dpm randomly failed on Vega10
drm/amdgpu: set f_mapping on exported DMA-bufs
drm/amdgpu: Properly allocate VM invalidate eng v2
drm/fsl-dcu: enable IRQ before drm_atomic_helper_resume()
drm/fsl-dcu: avoid disabling pixel clock twice on suspend
...
Bake in the conflict between the drm_print.h extraction and the
addition of DRM_DEBUG_LEASES since we lost it a few too many times.
Also fix a new use of drm_plane_helper_check_state in msm to follow
Ville's conversion in
commit a01cb8ba3f
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Wed Nov 1 22:16:19 2017 +0200
drm: Move drm_plane_helper_check_state() into drm_atomic_helper.c
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_plane_helper_check_update() isn't a transitional helper, so let's
rename it to drm_atomic_helper_check_plane_state() and move it into
drm_atomic_helper.c.
v2: Fix the WARNs about plane_state->crtc matching crtc_state->crtc
Cc: Daniel Vetter <daniel@ffwll.ch>
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171101201619.6175-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_plane_helper_check_state() is supposed to do things the atomic way,
so it should not be inspecting crtc->enabled. Rather we should be
looking at crtc_state->enable.
We have a slight complication due to drm_plane_helper_check_update()
reusing drm_plane_helper_check_state() for non-atomic drivers. Thus
we'll have to pass the crtc_state in manally and construct a fake
crtc_state in drm_plane_helper_check_update().
v2: Fix the WARNs about plane_state->crtc matching crtc_state->crtc
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171101201558.6059-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current implementation of the pad clock isn't quite correct. This
has the side-effect of being incompatible with the implementation for
Tegra186 (provided by the BPMP) and therefore would require a massive
change to the driver to cope with the differences. Instead, simply do
what Tegra186 does and add some code to fallback to the old behaviour
for existing device trees.
Signed-off-by: Thierry Reding <treding@nvidia.com>
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJaCm8RAAoJEAx081l5xIa+zX0QAJSm31kCG3vdw2CNiRx25L3q
3hcsEOgAjVJ9FQVGKFWjzb8TK35tSqtNx5kWIj0VGaIfBE5Bdg5SLLgKKUYas8rY
4LaphqICq2uxu2BNa2tpiar/sHhAnuozwQ4czpVWXzlaISnb9yYzRl7gMuyUVGkx
+Gih5VUhLmQC0HsRTLJ3vaZQoUsLAl2gAjKcWa1bx57j2S+iKOPfsLaq7VYo+y1I
Njc+iSGqMhJzRLXVkxL2lQKaslp7R38Bbh5K4Kvyjkm4Aq7zErOF6irpOXKMcrGl
mwnr89vf1G9thjikrBaXpKnuvdbWYveoN/ORMlTdCfxkFnChHLnm3bd7NJ49RXDN
Hv/Iq9YYjmZ9GTatxnx7lWtmXnZXC5he1yn1JAuz/yt7/0b/Wx+Mu/wEpBXYNFTd
1AZdD586i+AmPo3yDkqH9nBu8JC0W0AnS9VZma4LVvZOP2UfJmj5Im1CLHItbGDN
FnUCkwyD/lJUUk+WgT+w/GOMJgmFHDiFFl4tFtYVVjrUirpCFVguSKG9xuv6tT8P
8iRsoP7RrcmDN9ojN2SEHwcpsAv3HnKkDv+9+GIbWnrGsSbCPq8Qm+JDSvf4h22I
K5lwNpJrcpSKI+q10L7w2xliTBwb98sJkWGA/rssomrdBOWteGZAyqFRYAVgQ+mJ
x/nJurIqQYh2KQN9+uLG
=xVV2
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.15.
Core:
- Atomic object lifetime fixes
- Atomic iterator improvements
- Sparse/smatch fixes
- Legacy kms ioctls to be interruptible
- EDID override improvements
- fb/gem helper cleanups
- Simple outreachy patches
- Documentation improvements
- Fix dma-buf rcu races
- DRM mode object leasing for improving VR use cases.
- vgaarb improvements for non-x86 platforms.
New driver:
- tve200: Faraday Technology TVE200 block.
This "TV Encoder" encodes a ITU-T BT.656 stream and can be found in
the StorLink SL3516 (later Cortina Systems CS3516) as well as the
Grain Media GM8180.
New bridges:
- SiI9234 support
New panels:
- S6E63J0X03, OTM8009A, Seiko 43WVF1G, 7" rpi touch panel, Toshiba
LT089AC19000, Innolux AT043TN24
i915:
- Remove Coffeelake from alpha support
- Cannonlake workarounds
- Infoframe refactoring for DisplayPort
- VBT updates
- DisplayPort vswing/emph/buffer translation refactoring
- CCS fixes
- Restore GPU clock boost on missed vblanks
- Scatter list updates for userptr allocations
- Gen9+ transition watermarks
- Display IPC (Isochronous Priority Control)
- Private PAT management
- GVT: improved error handling and pci config sanitizing
- Execlist refactoring
- Transparent Huge Page support
- User defined priorities support
- HuC/GuC firmware refactoring
- DP MST fixes
- eDP power sequencing fixes
- Use RCU instead of stop_machine
- PSR state tracking support
- Eviction fixes
- BDW DP aux channel timeout fixes
- LSPCON fixes
- Cannonlake PLL fixes
amdgpu:
- Per VM BO support
- Powerplay cleanups
- CI powerplay support
- PASID mgr for kfd
- SR-IOV fixes
- initial GPU reset for vega10
- Prime mmap support
- TTM updates
- Clock query interface for Raven
- Fence to handle ioctl
- UVD encode ring support on Polaris
- Transparent huge page DMA support
- Compute LRU pipe tweaks
- BO flag to allow buffers to opt out of implicit sync
- CTX priority setting API
- VRAM lost infrastructure plumbing
qxl:
- fix flicker since atomic rework
amdkfd:
- Further improvements from internal AMD tree
- Usermode events
- Drop radeon support
nouveau:
- Pascal temperature sensor support
- Improved BAR2 handling
- MMU rework to support Pascal MMU
exynos:
- Improved HDMI/mixer support
- HDMI audio interface support
tegra:
- Prep work for tegra186
- Cleanup/fixes
msm:
- Preemption support for a5xx
- Display fixes for 8x96 (snapdragon 820)
- Async cursor plane fixes
- FW loading rework
- GPU debugging improvements
vc4:
- Prep for DSI panels
- fix T-format tiling scanout
- New madvise ioctl
Rockchip:
- LVDS support
omapdrm:
- omap4 HDMI CEC support
etnaviv:
- GPU performance counters groundwork
sun4i:
- refactor driver load + TCON backend
- HDMI improvements
- A31 support
- Misc fixes
udl:
- Probe/EDID read fixes.
tilcdc:
- Misc fixes.
pl111:
- Support more variants
adv7511:
- Improve EDID handling.
- HDMI CEC support
sii8620:
- Add remote control support"
* tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux: (1480 commits)
drm/rockchip: analogix_dp: Use mutex rather than spinlock
drm/mode_object: fix documentation for object lookups.
drm/i915: Reorder context-close to avoid calling i915_vma_close() under RCU
drm/i915: Move init_clock_gating() back to where it was
drm/i915: Prune the reservation shared fence array
drm/i915: Idle the GPU before shinking everything
drm/i915: Lock llist_del_first() vs llist_del_all()
drm/i915: Calculate ironlake intermediate watermarks correctly, v2.
drm/i915: Disable lazy PPGTT page table optimization for vGPU
drm/i915/execlists: Remove the priority "optimisation"
drm/i915: Filter out spurious execlists context-switch interrupts
drm/amdgpu: use irq-safe lock for kiq->ring_lock
drm/amdgpu: bypass lru touch for KIQ ring submission
drm/amdgpu: Potential uninitialized variable in amdgpu_vm_update_directories()
drm/amdgpu: potential uninitialized variable in amdgpu_vce_ring_parse_cs()
drm/amd/powerplay: initialize a variable before using it
drm/amd/powerplay: suppress KASAN out of bounds warning in vega10_populate_all_memory_levels
drm/amd/amdgpu: fix evicted VRAM bo adjudgement condition
drm/vblank: Tune drm_crtc_accurate_vblank_count() WARN down to a debug
drm/rockchip: add CONFIG_OF dependency for lvds
...
* Enforce MSI multiple IRQ alignment in AMD IOMMU
* VT-d PASID error handling fixes
* Add r8a7795 IPMMU support
* Manage runtime PM links on exynos at {add,remove}_device callbacks
* Fix Mediatek driver name to avoid conflict
* Add terminate support to qcom fault handler
* 64-bit IOVA optimizations
* Simplfy IOVA domain destruction, better use of rcache, and
skip anchor nodes on copy
* Convert to IOMMU TLB sync API in io-pgtable-arm{-v7s}
* Drop command queue lock when waiting for CMD_SYNC completion on
ARM SMMU implementations supporting MSI to cacheable memory
* iomu-vmsa cleanup inspired by missed IOTLB sync callbacks
* Fix sleeping lock with preemption disabled for RT
* Dual MMU support for TI DRA7xx DSPs
* Optional flush option on IOVA allocation avoiding overhead when
caller can try other options
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=o4qF
-----END PGP SIGNATURE-----
Merge tag 'iommu-v4.15-rc1' of git://github.com/awilliam/linux-vfio
Pull IOMMU updates from Alex Williamson:
"As Joerg mentioned[1], he's out on paternity leave through the end of
the year and I'm filling in for him in the interim:
- Enforce MSI multiple IRQ alignment in AMD IOMMU
- VT-d PASID error handling fixes
- Add r8a7795 IPMMU support
- Manage runtime PM links on exynos at {add,remove}_device callbacks
- Fix Mediatek driver name to avoid conflict
- Add terminate support to qcom fault handler
- 64-bit IOVA optimizations
- Simplfy IOVA domain destruction, better use of rcache, and skip
anchor nodes on copy
- Convert to IOMMU TLB sync API in io-pgtable-arm{-v7s}
- Drop command queue lock when waiting for CMD_SYNC completion on ARM
SMMU implementations supporting MSI to cacheable memory
- iomu-vmsa cleanup inspired by missed IOTLB sync callbacks
- Fix sleeping lock with preemption disabled for RT
- Dual MMU support for TI DRA7xx DSPs
- Optional flush option on IOVA allocation avoiding overhead when
caller can try other options
[1] https://lkml.org/lkml/2017/10/22/72"
* tag 'iommu-v4.15-rc1' of git://github.com/awilliam/linux-vfio: (54 commits)
iommu/iova: Use raw_cpu_ptr() instead of get_cpu_ptr() for ->fq
iommu/mediatek: Fix driver name
iommu/ipmmu-vmsa: Hook up r8a7795 DT matching code
iommu/ipmmu-vmsa: Allow two bit SL0
iommu/ipmmu-vmsa: Make IMBUSCTR setup optional
iommu/ipmmu-vmsa: Write IMCTR twice
iommu/ipmmu-vmsa: IPMMU device is 40-bit bus master
iommu/ipmmu-vmsa: Make use of IOMMU_OF_DECLARE()
iommu/ipmmu-vmsa: Enable multi context support
iommu/ipmmu-vmsa: Add optional root device feature
iommu/ipmmu-vmsa: Introduce features, break out alias
iommu/ipmmu-vmsa: Unify ipmmu_ops
iommu/ipmmu-vmsa: Clean up struct ipmmu_vmsa_iommu_priv
iommu/ipmmu-vmsa: Simplify group allocation
iommu/ipmmu-vmsa: Unify domain alloc/free
iommu/ipmmu-vmsa: Fix return value check in ipmmu_find_group_dma()
iommu/vt-d: Clear pasid table entry when memory unbound
iommu/vt-d: Clear Page Request Overflow fault bit
iommu/vt-d: Missing checks for pasid tables if allocation fails
iommu/amd: Limit the IOVA page range to the specified addresses
...
drm_add_edid_modes() now fills in the ELD automatically, so the calls to
drm_edid_to_eld() are redundant. Remove them.
All the other places are obvious, but nv50 has detached
drm_edid_to_eld() from the drm_add_edid_modes() call.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0959ca02b983afc9e74dd9acd190ba6e25f21678.1509545641.git.jani.nikula@intel.com
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to support CEC the HDMI driver has to inform the CEC driver
whenever the physical address changes. So when the EDID is read the
CEC driver has to be informed and whenever the hotplug detect goes
away.
This is done through the cec-notifier framework.
The link between the HDMI driver and the CEC driver is done through
the hdmi-phandle property in the tegra-cec node in the device tree.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order for the reset to be applied properly, the module clock must be
enabled during the assertion.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When applying the PLL changes from the computed state object, make sure
to set the rate of the display controller module clock. Failing to do so
can yield to a situation where the parent will be set to the proper
pixel clock, but the module clock will be divided down to the rate that
is happened to be set to before the parent rate change.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove the tegra_dc_disable_window() function whose only purpose was to
allow tegra_plane_atomic_update() to also call it. Fix that by shuffling
tegra_plano_atomic_disable() to before tegra_plane_atomic_update().
While at it, also remove the overlay plane helper functions because they
are exactly the same as the primary plane helper functions.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Avoid some boilerplate by calling of_device_get_match_data() instead of
open-coding the equivalent in the driver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Avoid some boilerplate by calling of_device_get_match_data() instead of
open-coding the equivalent in the driver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Avoid some boilerplate by calling of_device_get_match_data() instead of
open-coding the equivalent in the driver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Avoid some boilerplate by calling of_device_get_match_data() instead of
open-coding the equivalent in the driver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the u64_to_user_ptr helper macro to cast IOCTL argument u64 values
to user pointers instead of writing out the cast manually. Also do
some other cleanup with user pointers to make them stand out more
and look cleaner.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add Tegra186 support for VIC - no changes are required except for new
firmware and compatibility string.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rather than request syncpoints for a struct device *, request them for a
struct host1x_client *. This is important because subsequent patches are
going to break the assumption that host1x will always be the parent for
devices requesting a syncpoint. It's also a more natural choice because
host1x clients are really the only ones that will know how to deal with
syncpoints.
Note that host1x clients are always guaranteed to be children of host1x,
regardless of their location in the device tree.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Now that the cached node optimisation can apply to all allocations, the
couple of users which were playing tricks with dma_32bit_pfn in order to
benefit from it can stop doing so. Conversely, there is also no need for
all the other users to explicitly calculate a 'real' 32-bit PFN, when
init_iova_domain() can happily do that itself from the page granularity.
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Jonathan Hunter <jonathanh@nvidia.com>
CC: David Airlie <airlied@linux.ie>
CC: Sudeep Dutt <sudeep.dutt@intel.com>
CC: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Zhen Lei <thunder.leizhen@huawei.com>
Tested-by: Nate Watterson <nwatters@codeaurora.org>
[rm: use iova_shift(), rewrote commit message]
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The TRACE_INCLUDE_FILE macro needs to specify the path relative to the
define_trace.h header rather than relative to the file defining it.
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170823171326.23620-1-thierry.reding@gmail.com
This contains a couple of fixes and improvements for host1x, with some
preparatory work for Tegra186 support.
The remainder is cleanup and minor bugfixes for Tegra DRM along with
enhancements to debuggability.
There have also been some enhancements to the kernel interfaces for
host1x job submissions and support for mmap'ing PRIME buffers directly,
all of which get the interfaces very close to ready for serious work.
-----BEGIN PGP SIGNATURE-----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=ZaxL
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.14-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.14-rc1
This contains a couple of fixes and improvements for host1x, with some
preparatory work for Tegra186 support.
The remainder is cleanup and minor bugfixes for Tegra DRM along with
enhancements to debuggability.
There have also been some enhancements to the kernel interfaces for
host1x job submissions and support for mmap'ing PRIME buffers directly,
all of which get the interfaces very close to ready for serious work.
* tag 'drm/tegra/for-4.14-rc1' of git://anongit.freedesktop.org/tegra/linux: (21 commits)
drm/tegra: Prevent BOs from being freed during job submission
drm/tegra: gem: Implement mmap() for PRIME buffers
drm/tegra: Support render node
drm/tegra: sor: Trace register accesses
drm/tegra: dpaux: Trace register accesses
drm/tegra: dsi: Trace register accesses
drm/tegra: hdmi: Trace register accesses
drm/tegra: dc: Trace register accesses
drm/tegra: sor: Use unsigned int for register offsets
drm/tegra: hdmi: Use unsigned int for register offsets
drm/tegra: dsi: Use unsigned int for register offsets
drm/tegra: dpaux: Use unsigned int for register offsets
drm/tegra: dc: Use unsigned int for register offsets
drm/tegra: Fix NULL deref in debugfs/iova
drm/tegra: switch to drm_*_get(), drm_*_put() helpers
drm/tegra: Set MODULE_FIRMWARE for the VIC
drm/tegra: Add CONFIG_OF dependency
gpu: host1x: Support sub-devices recursively
gpu: host1x: fix error return code in host1x_probe()
gpu: host1x: Fix bitshift/mask multipliers
...
Since DRM IOCTL's are lockless, there is a chance that BOs could be
released while a job submission is in progress. To avoid that, keep the
GEM reference until the job has been pinned, part of which will be to
take another reference.
v2: remove redundant check and avoid memory leak
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The mapping of PRIME buffers can reuse much of the GEM mapping code, so
extract the common bits into a new tegra_gem_mmap() helper.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
None of the driver-specific IOCTLs are privileged, so mark them as such
and advertise that the driver supports render nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Register offsets are usually fairly small numbers, so an unsigned int is
more than enough to represent them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Register offsets are usually fairly small numbers, so an unsigned int is
more than enough to represent them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Register offsets are usually fairly small numbers, so an unsigned int is
more than enough to represent them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Register offsets are usually fairly small numbers, so an unsigned int is
more than enough to represent them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Register offsets are usually fairly small numbers, so an unsigned int is
more than enough to represent them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When IOMMU is off, ->mm_lock is not initialized and ->mm is NULL.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use drm_*_get() and drm_*_put() helpers instead of drm_*_reference()
and drm_*_unreference() helpers.
drm_*_reference() and drm_*_unreference() functions are just
compatibility alias for drm_*_get() and drm_*_put() and should not be
used by new code. So convert all users of compatibility functions to
use the new APIs.
Generated by: scripts/coccinelle/api/drm-get-put.cocci
Signed-off-by: Cihangir Akturk <cakturk@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The defines are set anyway to prevent an empty string. The test for the
SoC is the same as for Nouveau for the Tegra GPU firmware (see
drivers/gpu/drm/nouveau/nouveau_platform.c)
v2:
- Place the defines above each chip's vic_config struct
- MODULE_FIRMWARE() at the end of the file
Fixes: 0ae797a8ba ("drm/tegra: Add VIC support")
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Without CONFIG_OF, we can run into a build error:
drivers/gpu/drm/tegra/dpaux.c:378:20: error: 'pinconf_generic_dt_node_to_map_group' undeclared here (not in a function); did you mean 'pinconf_generic_params'?
.dt_node_to_map = pinconf_generic_dt_node_to_map_group,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
pinconf_generic_params
drivers/gpu/drm/tegra/dpaux.c:379:17: error: 'pinconf_generic_dt_free_map' undeclared here (not in a function); did you mean 'pinconf_generic_params'?
This adds an explicit dependency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
It's dead code, the core handles all this directly now.
The only special case is nouveau and tda988x which used one function
for both legacy modeset code and -nv50 atomic world instead of 2
vtables. But amounts to exactly the same.
v2: Rebase over the panel/brideg refactorings in stm/ltdc.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Peter Senna Tschudin <peter.senna@collabora.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Yakir Yang <kuankuan.y@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Romain Perier <romain.perier@collabora.com>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Hai Li <hali@codeaurora.org>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-tegra@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Cc: zain wang <wzz@rock-chips.com>
Cc: Baoyou Xie <baoyou.xie@linaro.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-8-daniel.vetter@ffwll.ch
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Philippe Cornu <philippe.cornu@st.com> (on stm)
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
This is the plumbing for supporting fb modifiers on planes. Modifiers
have already been introduced to some extent, but this series will extend
this to allow querying modifiers per plane. Based on this, the client to
enable optimal modifications for framebuffers.
This patch simply allows the DRM drivers to initialize their list of
supported modifiers upon initializing the plane.
v2: A minor addition from Daniel
v3:
* Updated commit message
* s/INVALID/DRM_FORMAT_MOD_INVALID (Liviu)
* Remove some excess newlines (Liviu)
* Update comment for > 64 modifiers (Liviu)
v4: Minor comment adjustments (Liviu)
v5: Some new platforms added due to rebase
v6: Add some missed plane inits (or maybe they're new - who knows at
this point) (Daniel)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Daniel Stone <daniels@collabora.com> (v2)
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Stone <daniels@collabora.com>
drm_atomic_helper_swap_state() will be changed to interruptible waiting
in the next few commits, so all drivers have to be changed to handling
failure.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Link: http://patchwork.freedesktop.org/patch/msgid/20170711143314.2148-9-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HDMI 1.4b support the CEA video modes as per range of CEA-861-D (VIC 1-64).
For any other mode, the VIC filed in AVI infoframes should be 0.
HDMI 2.0 sinks, support video modes range as per CEA-861-F spec, which is
extended to (VIC 1-107).
This patch adds a bool input variable, which indicates if the connected
sink is a HDMI 2.0 sink or not. This will make sure that we don't pass a
HDMI 2.0 VIC to a HDMI 1.4 sink.
This patch touches all drm drivers, who are callers of this function
drm_hdmi_avi_infoframe_from_display_mode but to make sure there is
no change in current behavior, is_hdmi2 is kept as false.
In case of I915 driver, this patch:
- checks if the connected display is HDMI 2.0.
- HDMI infoframes carry one of this two type of information:
- VIC for 4K modes for HDMI 1.4 sinks
- S3D information for S3D modes
As CEA-861-F has already defined VICs for 4K videomodes, this
patch doesn't allow sending HDMI infoframes for HDMI 2.0 sinks,
until the mode is 3D.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jose Abreu <jose.abreu@synopsys.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
PS: This patch touches a few lines in few files, which were
already above 80 char, so checkpatch gives 80 char warning again.
- gpu/drm/omapdrm/omap_encoder.c
- gpu/drm/i915/intel_sdvo.c
V2: Rebase, Added r-b from Andrzej
V3: Addressed review comment from Ville:
- Do not send VICs in both AVI-IF and HDMI-IF
send only one of it.
V4: Rebase
V5: Added r-b from Neil.
Addressed review comments from Ville
- Do not block HDMI vendor IF, instead check for VIC while
handling AVI infoframes
V6: Rebase
V7: Rebase
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1499960000-9232-2-git-send-email-shashank.sharma@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The CRTC .disable() helper operation is deprecated for atomic drivers,
the new .atomic_disable() helper operation being preferred. Convert all
atomic drivers to .atomic_disable() to avoid cargo-cult use of
.disable() in new drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # for sun4i
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> # for mediatek
Acked-by: Alexey Brodkin <abrodkin@synopsys.com> # for arcpgu
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # for atmel-hlcdc
Tested-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Vincent Abriou <vincent.abriou@st.com> # for sti
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> # for vmwgfx
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630093646.7928-3-laurent.pinchart+renesas@ideasonboard.com
The old state is useful for drivers that need to perform operations at
enable time that depend on the transition between the old and new
states.
While at it, rename the operation to .atomic_enable() to be consistent
with .atomic_disable(), as the .enable() operation is used by atomic
helpers only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # for sun4i
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> # for imx-drm and mediatek
Acked-by: Alexey Brodkin <abrodkin@synopsys.com> # for arcpgu
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # for atmel-hlcdc
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com> # for hdlcd and mali-dp
Acked-by: Stefan Agner <stefan@agner.ch> # for fsl-dcu
Tested-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Vincent Abriou <vincent.abriou@st.com> # for sti
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> # for vmwgfx
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630093646.7928-2-laurent.pinchart+renesas@ideasonboard.com
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZUGOmAAoJEHm+PkMAQRiGhX8H/3fIhingPD01MBf98U0xGrJo
yIXmhu6nFs7TM0lDVDcHsKgqLQIT69ll7PrSZrMkc1RGUIPINoCuJVuJqDre0kfB
of5TX2KegqSx8h1vOWjGBCBjdYfPGyMdf9icf6KsGc/SlIdhN6WA99kglAjJA0Ve
qPTNagF0ntUNg1lsXffxyfcHqFpyqw/Z/C4ie/byFsn9iJ1VG9mNlTWSud09vhuM
3tvHzTUVAIWWuRrrgrvgqQpnwL+q5BfSDsXScMjBau0EK3RGGqG8EN6Kbkfa7VQ6
aBoeboQjUijSJnVwvySdQ11MChTIOwZdfrNPra/1HD3WJNsSu4BIRt5JcAKcOhc=
=qmSg
-----END PGP SIGNATURE-----
Backmerge tag 'v4.12-rc7' into drm-next
Linux 4.12-rc7
Needed at least rc6 for drm-misc-next-fixes, may as well go to rc7
This starts off with the addition of more documentation for the host1x
and DRM drivers and finishes with a slew of fixes and enhancements for
the staging IOCTLs as a result of the awesome work done by Dmitry and
Erik on the grate reverse-engineering effort.
-----BEGIN PGP SIGNATURE-----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=zz/Z
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.13-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.13-rc1
This starts off with the addition of more documentation for the host1x
and DRM drivers and finishes with a slew of fixes and enhancements for
the staging IOCTLs as a result of the awesome work done by Dmitry and
Erik on the grate reverse-engineering effort.
* tag 'drm/tegra/for-4.13-rc1' of git://anongit.freedesktop.org/tegra/linux:
gpu: host1x: At first try a non-blocking allocation for the gather copy
gpu: host1x: Refactor channel allocation code
gpu: host1x: Remove unused host1x_cdma_stop() definition
gpu: host1x: Remove unused 'struct host1x_cmdbuf'
gpu: host1x: Check waits in the firewall
gpu: host1x: Correct swapped arguments in the is_addr_reg() definition
gpu: host1x: Forbid unrelated SETCLASS opcode in the firewall
gpu: host1x: Forbid RESTART opcode in the firewall
gpu: host1x: Forbid relocation address shifting in the firewall
gpu: host1x: Do not leak BO's phys address to userspace
gpu: host1x: Correct host1x_job_pin() error handling
gpu: host1x: Initialize firewall class to the job's one
drm/tegra: dc: Disable plane if it is invisible
drm/tegra: dc: Apply clipping to the plane
drm/tegra: dc: Avoid reset asserts on Tegra20
drm/tegra: Check syncpoint ID in the 'submit' IOCTL
drm/tegra: Correct copying of waitchecks and disable them in the 'submit' IOCTL
drm/tegra: Check for malformed offsets and sizes in the 'submit' IOCTL
drm/tegra: Add driver documentation
gpu: host1x: Flesh out kerneldoc
This is largely a rewrite of the Host1x channel allocation code, bringing
several changes:
- The previous code could deadlock due to an interaction
between the 'reflock' mutex and CDMA timeout handling.
This gets rid of the mutex.
- Support for more than 32 channels, required for Tegra186
- General refactoring, including better encapsulation
of channel ownership handling into channel.c
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Several channels could be made to write the same unit concurrently via
the SETCLASS opcode, trusting userspace is a bad idea. It should be
possible to drop the per-client channel reservation and add a per-unit
locking by inserting MLOCK's to the command stream to re-allow the
SETCLASS opcode, but it will be much more work. Let's forbid the
unit-unrelated class changes for now.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Erik Faye-Lund <kusmabite@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tegra20 if plane has width or height equal to 0, it will be infinitely
wide or tall. Let's disable the plane if it is invisible on atomic state
committing to fix the issue. The Rockchip DRM driver does the same.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Erik Faye-Lund <kusmabite@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tegra20 an overlay plane should be clipped, otherwise its output is
distorted once plane crosses display boundary.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Erik Faye-Lund <kusmabite@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit 33a8eb8d40 ("drm/tegra: dc: Implement runtime PM") introduced
HW reset control. It causes a hang on Tegra20 if both display
controllers are utilized (RGB panel and HDMI). The TRM suggests that
each display controller has its own reset control, apparently it is not
correct.
Fixes: 33a8eb8d40 ("drm/tegra: dc: Implement runtime PM")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Erik Faye-Lund <kusmabite@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In case of invalid syncpoint ID, the host1x_syncpt_get() returns NULL and
none of its users perform a check of the returned pointer later. Let's bail
out until it's too late.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The waitchecks along with multiple syncpoints per submit are not ready
for use yet, let's forbid them for now.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If commands buffer claims a number of words that is higher than its BO can
fit, a kernel OOPS will be fired on the out-of-bounds BO access. This was
triggered by an opentegra Xorg driver that erroneously pushed too many
commands to the pushbuf.
The CDMA commands buffer address is 4 bytes aligned, so check its
alignment.
The maximum number of the CDMA gather fetches is 16383, add a check for
it.
Add a sanity check for the relocations in a same way.
[ 46.829393] Unable to handle kernel paging request at virtual address f09b2000
...
[<c04a3ba4>] (host1x_job_pin) from [<c04dfcd0>] (tegra_drm_submit+0x474/0x510)
[<c04dfcd0>] (tegra_drm_submit) from [<c04deea0>] (tegra_submit+0x50/0x6c)
[<c04deea0>] (tegra_submit) from [<c04c07c0>] (drm_ioctl+0x1e4/0x3ec)
[<c04c07c0>] (drm_ioctl) from [<c02541a0>] (do_vfs_ioctl+0x9c/0x8e4)
[<c02541a0>] (do_vfs_ioctl) from [<c0254a1c>] (SyS_ioctl+0x34/0x5c)
[<c0254a1c>] (SyS_ioctl) from [<c0107640>] (ret_fast_syscall+0x0/0x3c)
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Erik Faye-Lund <kusmabite@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The client ID 0 is reserved by the host1x/cdma to mark the timeout timer
work as already been scheduled and context ID is used as the clients one.
This fixes spurious CDMA timeouts.
Fixes: bdd2f9cd10 ("drm/tegra: Don't leak kernel pointer to userspace")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/9c19a44219acd988e678cf9abe21363911184625.1497480754.git.digetx@gmail.com
UAPI Changes:
- Return -ENODEV instead of -ENXIO when creating cma fb w/o valid gem (Daniel)
- Add aspect ratio and custom scaling propertis to connector state (Maarten)
Cross-subsystem Changes:
- None
Core Changes:
- Add Laurent as bridge reviewer and Andrzej as bridge maintainer (Archit)
- Maintain new STM driver through -misc (Yannick)
- Misc doc improvements (as is tradition) (Daniel)
- Add driver-private objects to atomic state (Dhinakaran)
- Deprecate preclose hook in modern drivers (use postclose) (Daniel)
- Add hwmode to vblank struct. This fixes mode access in irq context and reduced
a bunch of boilerplate (Daniel)
Driver Changes:
- vc4: Add out-fence support to vc4 V3D rendering (Eric)
- stm: Add stm32f429 display hw and am-480272h3tmqw-t01h panel support (Yannick)
- vc4: Remove 256MB cma limit from vc4 (Eric)
- dw-hdmi: Disable audio when inactive, instead of always enabled (Romain)
- zte: Add support for VGA to the ZTE driver (Shawn)
- i915: Track DP MST bandwidth and check it in atomic_check (Dhinakaran)
- vgem: Enable gem dmabuf import iface to facilitate ion testing (Laura)
- vc4: Add support for Cygnus (new dt compat string + couple bug fixes) (Eric)
- pl111: Add driver for pl111 CLCD display controller (Eric/Tom)
- vgem: Subclass drm_device instead of standalone platform device (Chris)
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: Romain Perier <romain.perier@collabora.com>
Cc: Navare, Manasi D <manasi.d.navare@intel.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Tom Cooksey <tom.cooksey@arm.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
* tag 'drm-misc-next-2017-05-16' of git://anongit.freedesktop.org/git/drm-misc: (72 commits)
drm: add missing declaration to drm_blend.h
drm/dp: Wait up all outstanding tx waiters
drm/dp: Read the tx msg state once after checking for an event
drm/prime: Forward declare struct device
drm/vblank: Lock down vblank->hwmode more
drm/vblank: drop the mode argument from drm_calc_vbltimestamp_from_scanoutpos
drm/vblank: Add FIXME comments about moving the vblank ts hooks
drm/vblank: Switch to bool in_vblank_irq in get_vblank_timestamp
drm/vblank: Switch drm_driver->get_vblank_timestamp to return a bool
drm/vgem: Convert to a struct drm_device subclass
gpu: drm: gma500: remove dead code
drm/sti: Adjust two checks for null pointers in sti_hqvdp_probe()
drm/sti: Fix typos in a comment line
drm/sti: Fix a typo in a comment line
drm/sti: Replace 17 seq_puts() calls by seq_putc()
drm/sti: Reduce function calls for sequence output at five places
drm/sti: use seq_puts to display a string
drm: Nerf the preclose callback for modern drivers
drm/exynos: Merge pre/postclose hooks
drm/tegra: switch to postclose
...
I didn't spot anything that would require ordering here (well not
anywhere else either), and I'm trying to unify at least modern drivers
on one close hook.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-tegra@vger.kernel.org
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170508082633.4214-2-daniel.vetter@ffwll.ch
This contains various fixes to the host1x driver as well as a plug for a
leak of kernel pointers to userspace.
A fairly big addition this time around is the Video Image Composer (VIC)
support that can be used to accelerate some 2D and image compositing
operations.
Furthermore the driver now supports FB modifiers, so we no longer rely
on a custom IOCTL to set those.
Finally this contains a few preparatory patches for Tegra186 support
which unfortunately didn't quite make it this time, but will hopefully
be ready for v4.13.
-----BEGIN PGP SIGNATURE-----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=Eqtp
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.12-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.12-rc1
This contains various fixes to the host1x driver as well as a plug for a
leak of kernel pointers to userspace.
A fairly big addition this time around is the Video Image Composer (VIC)
support that can be used to accelerate some 2D and image compositing
operations.
Furthermore the driver now supports FB modifiers, so we no longer rely
on a custom IOCTL to set those.
Finally this contains a few preparatory patches for Tegra186 support
which unfortunately didn't quite make it this time, but will hopefully
be ready for v4.13.
* tag 'drm/tegra/for-4.12-rc1' of git://anongit.freedesktop.org/tegra/linux:
gpu: host1x: Fix host1x driver shutdown
gpu: host1x: Support module reset
gpu: host1x: Sort includes alphabetically
drm/tegra: Add VIC support
dt-bindings: Add bindings for the Tegra VIC
drm/tegra: Add falcon helper library
drm/tegra: Add Tegra DRM allocation API
drm/tegra: Add tiling FB modifiers
drm/tegra: Don't leak kernel pointer to userspace
drm/tegra: Protect IOMMU operations by mutex
drm/tegra: Enable IOVA API when IOMMU support is enabled
gpu: host1x: Add IOMMU support
gpu: host1x: Fix potential out-of-bounds access
iommu/iova: Fix compile error with CONFIG_IOMMU_IOVA=m
iommu: Add dummy implementations for !IOMMU_IOVA
MAINTAINERS: Add related headers to IOMMU section
iommu/iova: Consolidate code for adding new node to iovad domain rbtree
Seeing the kunmap_atomic dma_buf_ops share the same name with a macro
in highmem.h, the former can be aliased if any dma-buf user includes
that header.
I'm personally trying to include highmem.h inside scatterlist.h and this
breaks the dma-buf code proper.
Christoph Hellwig suggested [1] renaming it and pushing this patch ASAP.
To maintain consistency I've renamed all four of kmap* and kunmap* to be
map* and unmap*. (Even though only kmap_atomic presently conflicts.)
[1] https://www.spinics.net/lists/target-devel/msg15070.html
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1492630570-879-1-git-send-email-logang@deltatee.com
This patch adds support for Video Image Compositor engine which
can be used for 2d operations.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Arto Merilainen <amerilainen@nvidia.com>
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a set of falcon helper routines for use by the tegradrm client drivers
of the various falcon-based engines.
The falcon is a microcontroller that acts as a frontend for the rest of a
particular Tegra engine. In order to properly utilize these engines, the
frontend must be booted before pushing any commands.
Based on work by Andrew Chew <achew@nvidia.com>
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Arto Merilainen <amerilainen@nvidia.com>
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a new IO virtual memory allocation API to allow clients to
allocate non-GEM memory in the Tegra DRM IOMMU domain. This is
required e.g. for loading client firmware when clients are attached
to the IOMMU domain.
The allocator allocates contiguous physical pages that are then
mapped contiguously to the IOMMU domain using the iova_domain
library provided by the kernel. Contiguous physical pages are
used so that the same allocator works also when IOMMU support
is disabled and therefore devices access physical memory directly.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add FB modifiers to allow user-space to specify that a surface is in one
of the two tiling formats supported by Tegra chips, and add support in
the tegradrm driver to handle them properly. This is necessary for the
display controller to directly display buffers generated by the GPU.
This feature is intended to replace the dedicated IOCTL enabled
by TEGRA_STAGING and to provide a non-staging alternative to that
solution.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Each open file descriptor can have any number of contexts associated
with it. To differentiate between these contexts a unique ID is required
and back when these userspace interfaces were introduced, in commit
d43f81cbaf ("drm/tegra: Add gr2d device"), the pointer to the context
structure was deemed adequate. However, this leaks information about
kernel internal memory to userspace, which can potentially be exploited.
Switch the context parameter to be allocated from an IDR, which has the
added benefit of providing an easy way to look up a context from its ID.
Signed-off-by: Thierry Reding <treding@nvidia.com>
IOMMU support is currently not thread-safe, which can cause crashes,
amongst other things, under certain workloads.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When support for an IOMMU has been enabled, make sure the IOVA helper
code is also activated and the driver can properly manage the IO virtual
address space.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Yes the help text is unhelpful, but atomic drivers should never use
this. Just grab the lock without context or anything.
Also an aside: Checking ->active like this doesn't protect against
nonblocking commits, this is rather bogus.
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170322215058.8671-8-daniel.vetter@ffwll.ch
-----BEGIN PGP SIGNATURE-----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=BSWh
-----END PGP SIGNATURE-----
Merge tag 'doc-4.11-images' of git://git.lwn.net/linux into drm-misc-next
Pointer for Markus's image conversion work.
We need this so we can merge all the pretty drm graphs for 4.12.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
->fault(), ->page_mkwrite(), and ->pfn_mkwrite() calls do not need to
take a vma and vmf parameter when the vma already resides in vmf.
Remove the vma parameter to simplify things.
[arnd@arndb.de: fix ARM build]
Link: http://lkml.kernel.org/r/20170125223558.1451224-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/148521301778.19116.10840599906674778980.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The vblank hooks in struct drm_driver are deprecated and only meant for
legacy drivers. For modern drivers with DRIVER_MODESET flag, the hooks
in struct drm_crtc_funcs should be used instead.
As the result, the wrapper functions tegra_drm_xxx get killed
completely, and tegra_dc_xxx are filled into struct drm_crtc_funcs as
vblank hooks directly.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1486458995-31018-21-git-send-email-shawnguo@kernel.org
Noticed that everyone duplicates the same logic here and we could safe
a few lines per driver. Yay for lots of drivers to make such tiny
refactors worth-while!
v2: Forgot to git add everything :(
v3: Actually remove release_fbi (Sean, Emil, Chris) ...
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207161603.17611-1-daniel.vetter@ffwll.ch
The drm_mm range manager claimed to support top-down insertion, but it
was neither searching for the top-most hole that could fit the
allocation request nor fitting the request to the hole correctly.
In order to search the range efficiently, we create a secondary index
for the holes using either their size or their address. This index
allows us to find the smallest hole or the hole at the bottom or top of
the range efficiently, whilst keeping the hole stack to rapidly service
evictions.
v2: Search for holes both high and low. Rename flags to mode.
v3: Discover rb_entry_safe() and use it!
v4: Kerneldoc for enum drm_mm_insert_mode.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com> # vmwgfx
Reviewed-by: Lucas Stach <l.stach@pengutronix.de> #etnaviv
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170202210438.28702-1-chris@chris-wilson.co.uk
Instead of receiving the num_crts as a parameter, we can read it
directly from the mode_config structure. I audited the drivers that
invoke this helper and I believe all of them initialize the mode_config
struct accordingly, prior to calling the fb_helper.
I used the following coccinelle hack to make this transformation, except
for the function headers and comment updates. The first and second
rules are split because I couldn't find a way to remove the unused
temporary variables at the same time I removed the parameter.
// <smpl>
@r@
expression A,B,D,E;
identifier C;
@@
(
- drm_fb_helper_init(A,B,C,D)
+ drm_fb_helper_init(A,B,D)
|
- drm_fbdev_cma_init_with_funcs(A,B,C,D,E)
+ drm_fbdev_cma_init_with_funcs(A,B,D,E)
|
- drm_fbdev_cma_init(A,B,C,D)
+ drm_fbdev_cma_init(A,B,D)
)
@@
expression A,B,C,D,E;
@@
(
- drm_fb_helper_init(A,B,C,D)
+ drm_fb_helper_init(A,B,D)
|
- drm_fbdev_cma_init_with_funcs(A,B,C,D,E)
+ drm_fbdev_cma_init_with_funcs(A,B,D,E)
|
- drm_fbdev_cma_init(A,B,C,D)
+ drm_fbdev_cma_init(A,B,D)
)
@@
identifier r.C;
type T;
expression V;
@@
- T C;
<...
when != C
- C = V;
...>
// </smpl>
Changes since v1:
- Rebased on top of the tip of drm-misc-next.
- Remove mention to sti since a proper fix got merged.
Suggested-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170202162640.27261-1-krisman@collabora.co.uk
Function tegra_crtc_from_pipe() does the exactly same thing as what
crtc helper drm_crtc_from_index() provides. Use the helper to save
some code.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1483961145-18453-6-git-send-email-shawnguo@kernel.org
Back to regular -misc pulls with reasonable sizes:
- dma_fence error clarification (Chris)
- drm_crtc_from_index helper (Shawn), pile more patches on the m-l to roll
this out to drivers
- mmu-less support for fbdev helpers from Benjamin
- piles of kerneldoc work
- some polish for crc support from Tomeu and Benjamin
- odd misc stuff all over
* tag 'drm-misc-next-2017-01-09' of git://anongit.freedesktop.org/git/drm-misc: (48 commits)
dma-fence: Introduce drm_fence_set_error() helper
dma-fence: Wrap querying the fence->status
dma-fence: Clear fence->status during dma_fence_init()
drm: fix compilations issues introduced by "drm: allow to use mmuless SoC"
drm: Change the return type of the unload hook to void
drm: add more document for drm_crtc_from_index()
drm: remove useless parameters from drm_pick_cmdline_mode function
drm: crc: Call wake_up_interruptible() each time there is a new CRC entry
drm: allow to use mmuless SoC
drm: compile drm_vm.c only when needed
fbmem: add a default get_fb_unmapped_area function
drm: crc: Wait for a frame before returning from open()
drm: Move locking into drm_debugfs_crtc_crc_add
drm/imx: imx-tve: Remove unused variable
Revert "drm: nouveau: fix build when LEDS_CLASS=m"
drm: Add kernel-doc for drm_crtc_commit_get/put
drm/atomic: Fix outdated comment.
drm: reference count event->completion
gpu: drm: mgag200: mgag200_main:- Handle error from pci_iomap
drm: Document deprecated load/unload hook
...
The integer returned by the unload hook is ignored by the drm core, so
let's make it void.
This patch was created using the following Coccinelle semantic script
(except for the declaration and comment in drm_drv.h):
Compile-tested only.
// <smpl>
@ get_name @
struct drm_driver drv;
identifier fn;
@@
drv.unload = fn;
@ replace_type @
identifier get_name.fn;
@@
- int
+ void
fn (...)
{
...
}
@ remove_return_param @
identifier get_name.fn;
@@
void fn (...)
{
<...
if (...)
return
- ...
;
...>
}
@ drop_final_return @
identifier get_name.fn;
@@
void fn (...)
{
...
- return 0;
}
// </smpl>
Suggested-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Acked-by: Christian König <christian.koenig@amd.com>.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170106175731.29196-1-krisman@collabora.co.uk
First -misc pull for 4.11:
- drm_mm rework + lots of selftests (Chris Wilson)
- new connector_list locking+iterators
- plenty of kerneldoc updates
- format handling rework from Ville
- atomic helper changes from Maarten for better plane corner-case handling
in drivers, plus the i915 legacy cursor patch that needs this
- bridge cleanup from Laurent
- plus plenty of small stuff all over
- also contains a merge of the 4.10 docs tree so that we could apply the
dma-buf kerneldoc patches
It's a lot more than usual, but due to the merge window blackout it also
covers about 4 weeks, so all in line again on a per-week basis. The more
annoying part with no pull request for 4 weeks is managing cross-tree
work. The -intel pull request I'll follow up with does conflict quite a
bit with -misc here. Longer-term (if drm-misc keeps growing) a
drm-next-queued to accept pull request for the next merge window during
this time might be useful.
I'd also like to backmerge -rc2+this into drm-intel next week, we have
quite a pile of patches waiting for the stuff in here.
* tag 'drm-misc-next-2016-12-30' of git://anongit.freedesktop.org/git/drm-misc: (126 commits)
drm: Add kerneldoc markup for new @scan parameters in drm_mm
drm/mm: Document locking rules
drm: Use drm_mm_insert_node_in_range_generic() for everyone
drm: Apply range restriction after color adjustment when allocation
drm: Wrap drm_mm_node.hole_follows
drm: Apply tight eviction scanning to color_adjust
drm: Simplify drm_mm scan-list manipulation
drm: Optimise power-of-two alignments in drm_mm_scan_add_block()
drm: Compute tight evictions for drm_mm_scan
drm: Fix application of color vs range restriction when scanning drm_mm
drm: Unconditionally do the range check in drm_mm_scan_add_block()
drm: Rename prev_node to hole in drm_mm_scan_add_block()
drm: Fix O= out-of-tree builds for selftests
drm: Extract struct drm_mm_scan from struct drm_mm
drm: Add asserts to catch overflow in drm_mm_init() and drm_mm_init_scan()
drm: Simplify drm_mm_clean()
drm: Detect overflow in drm_mm_reserve_node()
drm: Fix kerneldoc for drm_mm_scan_remove_block()
drm: Promote drm_mm alignment to u64
drm: kselftest for drm_mm and restricted color eviction
...
Several DRM drivers print the same initialization message right after
drm_dev_register, so move that to common code. The exception is i915,
which uses its own register handle, so let it keep its own message.
Notice that this was tested only with Exynos, but looks simple enough
for the other drivers.
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161228143216.26821-2-krisman@collabora.co.uk
Including all drivers. I thought about keeping small compat functions
to avoid having to change all drivers. But I really like the
drm_printer idea, so figured spreading it more widely is a good thing.
v2: Review from Chris:
- Natural argument order and better name for drm_mm_print.
- show_mm() macro in the selftest.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1483009764-8281-1-git-send-email-daniel.vetter@ffwll.ch
<drm/drm_crtc.h> used to define most of the in-kernel KMS API. It has
now been split into separate files for each object type, but still
includes most other KMS headers to avoid breaking driver compilation.
As a step towards fixing that problem, remove the inclusion of
<drm/drm_encoder.h> from <drm/drm_crtc.h> and include it instead where
appropriate. Also remove the forward declarations of the drm_encoder and
drm_encoder_helper_funcs structures from <drm/drm_crtc.h> as they're not
needed in the header.
<drm/drm_encoder.h> now has to include <drm/drm_mode.h> and contain a
forward declaration of struct drm_encoder in order to allow including it
as the first header in a compilation unit.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sinclair Yeh <syeh@vmware.com> # For vmwgfx
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1481709550-29226-2-git-send-email-laurent.pinchart+renesas@ideasonboard.com
Every single user of vmf->virtual_address typed that entry to unsigned
long before doing anything with it so the type of virtual_address does
not really provide us any additional safety. Just use masked
vmf->address which already has the appropriate type.
Link: http://lkml.kernel.org/r/1479460644-25076-3-git-send-email-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This has a couple of fixes for IOMMU support and some fixes for error
handling.
-----BEGIN PGP SIGNATURE-----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=sDMr
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.10-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.10-rc1
This has a couple of fixes for IOMMU support and some fixes for error
handling.
* tag 'drm/tegra/for-4.10-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: Set sgt pointer in BO pin
drm/tegra: Support kernel mappings with IOMMU
gpu: host1x: Add locking to syncpt
gpu: host1x: Store device address to all bufs
drm/tegra: gem: Remove some dead code
drm/tegra: sor: No need to free devm_ allocated memory
drm/tegra: Fix error handling
drm/tegra: dpaux: Fix error handling
