Otherwise it would display the virtual allocation size, which is often
much bigger than the RSS.
Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Fixes: e48ade5e23 ("drm/panfrost: show device-wide list of DRM GEM objects over DebugFS")
Tested-by: Christopher Healy <healych@amazon.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20250808010235.2831853-1-adrian.larumbe@collabora.com
non-drm:
rust:
- make ETIMEDOUT available
- add size constants up to SZ_2G
- add DMA coherent allocation bindings
mtd:
- driver for Intel GPU non-volatile storage
i2c
- designware quirk for Intel xe
core:
- atomic helpers: tune enable/disable sequences
- add task info to wedge API
- refactor EDID quirks
- connector: move HDR sink to drm_display_info
- fourcc: half-float and 32-bit float formats
- mode_config: pass format info to simplify
dma-buf:
- heaps: Give CMA heap a stable name
ci:
- add device tree validation and kunit
displayport:
- change AUX DPCD access probe address
- add quirk for DPCD probe
- add panel replay definitions
- backlight control helpers
fbdev:
- make CONFIG_FIRMWARE_EDID available on all arches
fence:
- fix UAF issues
format-helper:
- improve tests
gpusvm:
- introduce devmem only flag for allocation
- add timeslicing support to GPU SVM
ttm:
- improve eviction
sched:
- tracing improvements
- kunit improvements
- memory leak fixes
- reset handling improvements
color mgmt:
- add hardware gamma LUT handling helpers
bridge:
- add destroy hook
- switch to reference counted drm_bridge allocations
- tc358767: convert to devm_drm_bridge_alloc
- improve CEC handling
panel:
- switch to reference counter drm_panel allocations
- fwnode panel lookup
- Huiling hl055fhv028c support
- Raspberry Pi 7" 720x1280 support
- edp: KDC KD116N3730A05, N160JCE-ELL CMN, N116BCJ-EAK
- simple: AUO P238HAN01
- st7701: Winstar wf40eswaa6mnn0
- visionox: rm69299-shift
- Renesas R61307, Renesas R69328 support
- DJN HX83112B
hdmi:
- add CEC handling
- YUV420 output support
xe:
- WildCat Lake support
- Enable PanthorLake by default
- mark BMG as SRIOV capable
- update firmware recommendations
- Expose media OA units
- aux-bux support for non-volatile memory
- MTD intel-dg driver for non-volatile memory
- Expose fan control and voltage regulator in sysfs
- restructure migration for multi-device
- Restore GuC submit UAF fix
- make GEM shrinker drm managed
- SRIOV VF Post-migration recovery of GGTT nodes
- W/A additions/reworks
- Prefetch support for svm ranges
- Don't allocate managed BO for each policy change
- HWMON fixes for BMG
- Create LRC BO without VM
- PCI ID updates
- make SLPC debugfs files optional
- rework eviction rejection of bound external BOs
- consolidate PAT programming logic for pre/post Xe2
- init changes for flicker-free boot
- Enable GuC Dynamic Inhibit Context switch
i915:
- drm_panic support for i915/xe
- initial flip queue off by default for LNL/PNL
- Wildcat Lake Display support
- Support for DSC fractional link bpp
- Support for simultaneous Panel Replay and Adaptive sync
- Support for PTL+ double buffer LUT
- initial PIPEDMC event handling
- drm_panel_follower support
- DPLL interface renames
- allocate struct intel_display dynamically
- flip queue preperation
- abstract DRAM detection better
- avoid GuC scheduling stalls
- remove DG1 force probe requirement
- fix MEI interrupt handler on RT kernels
- use backlight control helpers for eDP
- more shared display code refactoring
amdgpu:
- add userq slot to INFO ioctl
- SR-IOV hibernation support
- Suspend improvements
- Backlight improvements
- Use scaling for non-native eDP modes
- cleaner shader updates for GC 9.x
- Remove fence slab
- SDMA fw checks for userq support
- RAS updates
- DMCUB updates
- DP tunneling fixes
- Display idle D3 support
- Per queue reset improvements
- initial smartmux support
amdkfd:
- enable KFD on loongarch
- mtype fix for ext coherent system memory
radeon:
- CS validation additional GL extensions
- drop console lock during suspend/resume
- bump driver version
msm:
- VM BIND support
- CI: infrastructure updates
- UBWC single source of truth
- decouple GPU and KMS support
- DP: rework I/O accessors
- DPU: SM8750 support
- DSI: SM8750 support
- GPU: X1-45 support and speedbin support for X1-85
- MDSS: SM8750 support
nova:
- register! macro improvements
- DMA object abstraction
- VBIOS parser + fwsec lookup
- sysmem flush page support
- falcon: generic falcon boot code and HAL
- FWSEC-FRTS: fb setup and load/execute
ivpu:
- Add Wildcat Lake support
- Add turbo flag
ast:
- improve hardware generations implementation
imx:
- IMX8qxq Display Controller support
lima:
- Rockchip RK3528 GPU support
nouveau:
- fence handling cleanup
panfrost:
- MT8370 support
- bo labeling
- 64-bit register access
qaic:
- add RAS support
rockchip:
- convert inno_hdmi to a bridge
rz-du:
- add RZ/V2H(P) support
- MIPI-DSI DCS support
sitronix:
- ST7567 support
sun4i:
- add H616 support
tidss:
- add TI AM62L support
- AM65x OLDI bridge support
bochs:
- drm panic support
vkms:
- YUV and R* format support
- use faux device
vmwgfx:
- fence improvements
hyperv:
- move out of simple
- add drm_panic support
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEEKbZHaGwW9KfbeusDHTzWXnEhr4FAmiJM/0ACgkQDHTzWXnE
hr6MpA/+JJKGdSdrE95QkaMcOZh/3e3areGXZ0V/RrrJXdB4/DoAfQSHhF0H7m7y
MhBGVLGNMXq7KHrz28p1MjLHrE1mwmvJ6hZ4J076ed4u9naoCD0m6k5w5wiue+KL
HyPR54ADxN0BYmgV0l/B0wj42KsHyTO4x4hdqPJu02V9Dtmx6FCh2ujkOF3p9nbK
GMwWDttl4KEKljD0IvQ9YIYJ66crYGx/XmZi7JoWRrS104K/h1u8qZuXBp5jVKTy
OZRAVyLdmJqdTOLH7l599MBBcEd/bNV37/LVwF4T5iFunEKOAiyN0QY0OR+IeRVh
ZfOv2/gp4UNyIfyahQ7LKLgEilNPGHoPitvDJPvBZxW2UjwXVNvA1QfdK5DAlVRS
D5NoFRjlFFCz8/c2hQwlKJ9o7eVgH3/pK0mwR7SPGQTuqzLFCrAfCuzUvg/gV++6
JFqmGKMHeCoxO2o4GMrwjFttStP41usxtV/D+grcbPteNO9UyKJS4C38n4eamJXM
a9Sy9APuAb6F0w5+yMItEF7TQifgmhIbm5AZHlxE1KoDQV6TdiIf1Gou5LeDGoL6
OACbXHJPL52tUnfCRpbfI4tE/IVyYsfL01JnvZ5cZZWItXfcIz76ykJri+E0G60g
yRl/zkimHKO4B0l/HSzal5xROXr+3VzeWehEiz/ot1VriP5OesA=
=n9MO
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2025-07-30' of https://gitlab.freedesktop.org/drm/kernel
Pull drm updates from Dave Airlie:
"Highlights:
- Intel xe enable Panthor Lake, started adding WildCat Lake
- amdgpu has a bunch of reset improvments along with the usual IP
updates
- msm got VM_BIND support which is important for vulkan sparse memory
- more drm_panic users
- gpusvm common code to handle a bunch of core SVM work outside
drivers.
Detail summary:
Changes outside drm subdirectory:
- 'shrink_shmem_memory()' for better shmem/hibernate interaction
- Rust support infrastructure:
- make ETIMEDOUT available
- add size constants up to SZ_2G
- add DMA coherent allocation bindings
- mtd driver for Intel GPU non-volatile storage
- i2c designware quirk for Intel xe
core:
- atomic helpers: tune enable/disable sequences
- add task info to wedge API
- refactor EDID quirks
- connector: move HDR sink to drm_display_info
- fourcc: half-float and 32-bit float formats
- mode_config: pass format info to simplify
dma-buf:
- heaps: Give CMA heap a stable name
ci:
- add device tree validation and kunit
displayport:
- change AUX DPCD access probe address
- add quirk for DPCD probe
- add panel replay definitions
- backlight control helpers
fbdev:
- make CONFIG_FIRMWARE_EDID available on all arches
fence:
- fix UAF issues
format-helper:
- improve tests
gpusvm:
- introduce devmem only flag for allocation
- add timeslicing support to GPU SVM
ttm:
- improve eviction
sched:
- tracing improvements
- kunit improvements
- memory leak fixes
- reset handling improvements
color mgmt:
- add hardware gamma LUT handling helpers
bridge:
- add destroy hook
- switch to reference counted drm_bridge allocations
- tc358767: convert to devm_drm_bridge_alloc
- improve CEC handling
panel:
- switch to reference counter drm_panel allocations
- fwnode panel lookup
- Huiling hl055fhv028c support
- Raspberry Pi 7" 720x1280 support
- edp: KDC KD116N3730A05, N160JCE-ELL CMN, N116BCJ-EAK
- simple: AUO P238HAN01
- st7701: Winstar wf40eswaa6mnn0
- visionox: rm69299-shift
- Renesas R61307, Renesas R69328 support
- DJN HX83112B
hdmi:
- add CEC handling
- YUV420 output support
xe:
- WildCat Lake support
- Enable PanthorLake by default
- mark BMG as SRIOV capable
- update firmware recommendations
- Expose media OA units
- aux-bux support for non-volatile memory
- MTD intel-dg driver for non-volatile memory
- Expose fan control and voltage regulator in sysfs
- restructure migration for multi-device
- Restore GuC submit UAF fix
- make GEM shrinker drm managed
- SRIOV VF Post-migration recovery of GGTT nodes
- W/A additions/reworks
- Prefetch support for svm ranges
- Don't allocate managed BO for each policy change
- HWMON fixes for BMG
- Create LRC BO without VM
- PCI ID updates
- make SLPC debugfs files optional
- rework eviction rejection of bound external BOs
- consolidate PAT programming logic for pre/post Xe2
- init changes for flicker-free boot
- Enable GuC Dynamic Inhibit Context switch
i915:
- drm_panic support for i915/xe
- initial flip queue off by default for LNL/PNL
- Wildcat Lake Display support
- Support for DSC fractional link bpp
- Support for simultaneous Panel Replay and Adaptive sync
- Support for PTL+ double buffer LUT
- initial PIPEDMC event handling
- drm_panel_follower support
- DPLL interface renames
- allocate struct intel_display dynamically
- flip queue preperation
- abstract DRAM detection better
- avoid GuC scheduling stalls
- remove DG1 force probe requirement
- fix MEI interrupt handler on RT kernels
- use backlight control helpers for eDP
- more shared display code refactoring
amdgpu:
- add userq slot to INFO ioctl
- SR-IOV hibernation support
- Suspend improvements
- Backlight improvements
- Use scaling for non-native eDP modes
- cleaner shader updates for GC 9.x
- Remove fence slab
- SDMA fw checks for userq support
- RAS updates
- DMCUB updates
- DP tunneling fixes
- Display idle D3 support
- Per queue reset improvements
- initial smartmux support
amdkfd:
- enable KFD on loongarch
- mtype fix for ext coherent system memory
radeon:
- CS validation additional GL extensions
- drop console lock during suspend/resume
- bump driver version
msm:
- VM BIND support
- CI: infrastructure updates
- UBWC single source of truth
- decouple GPU and KMS support
- DP: rework I/O accessors
- DPU: SM8750 support
- DSI: SM8750 support
- GPU: X1-45 support and speedbin support for X1-85
- MDSS: SM8750 support
nova:
- register! macro improvements
- DMA object abstraction
- VBIOS parser + fwsec lookup
- sysmem flush page support
- falcon: generic falcon boot code and HAL
- FWSEC-FRTS: fb setup and load/execute
ivpu:
- Add Wildcat Lake support
- Add turbo flag
ast:
- improve hardware generations implementation
imx:
- IMX8qxq Display Controller support
lima:
- Rockchip RK3528 GPU support
nouveau:
- fence handling cleanup
panfrost:
- MT8370 support
- bo labeling
- 64-bit register access
qaic:
- add RAS support
rockchip:
- convert inno_hdmi to a bridge
rz-du:
- add RZ/V2H(P) support
- MIPI-DSI DCS support
sitronix:
- ST7567 support
sun4i:
- add H616 support
tidss:
- add TI AM62L support
- AM65x OLDI bridge support
bochs:
- drm panic support
vkms:
- YUV and R* format support
- use faux device
vmwgfx:
- fence improvements
hyperv:
- move out of simple
- add drm_panic support"
* tag 'drm-next-2025-07-30' of https://gitlab.freedesktop.org/drm/kernel: (1479 commits)
drm/tidss: oldi: convert to devm_drm_bridge_alloc() API
drm/tidss: encoder: convert to devm_drm_bridge_alloc()
drm/amdgpu: move reset support type checks into the caller
drm/amdgpu/sdma7: re-emit unprocessed state on ring reset
drm/amdgpu/sdma6: re-emit unprocessed state on ring reset
drm/amdgpu/sdma5.2: re-emit unprocessed state on ring reset
drm/amdgpu/sdma5: re-emit unprocessed state on ring reset
drm/amdgpu/gfx12: re-emit unprocessed state on ring reset
drm/amdgpu/gfx11: re-emit unprocessed state on ring reset
drm/amdgpu/gfx10: re-emit unprocessed state on ring reset
drm/amdgpu/gfx9.4.3: re-emit unprocessed state on kcq reset
drm/amdgpu/gfx9: re-emit unprocessed state on kcq reset
drm/amdgpu: Add WARN_ON to the resource clear function
drm/amd/pm: Use cached metrics data on SMUv13.0.6
drm/amd/pm: Use cached data for min/max clocks
gpu: nova-core: fix bounds check in PmuLookupTableEntry::new
drm/amdgpu: Replace HQD terminology with slots naming
drm/amdgpu: Add user queue instance count in HW IP info
drm/amd/amdgpu: Add helper functions for isp buffers
drm/amd/amdgpu: Initialize swnode for ISP MFD device
...
Panfrost can skip the reset if TDR has fired before the free-job worker.
Currently, since Panfrost doesn't take any action on these scenarios, the
job is being leaked, considering that `free_job()` won't be called.
To avoid such leaks, inform the scheduler that the job did not actually
timeout and no reset was performed through the new status code
DRM_GPU_SCHED_STAT_NO_HANG.
Reviewed-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250714-sched-skip-reset-v6-8-5c5ba4f55039@igalia.com
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Among the scheduler's statuses, the only one that indicates an error is
DRM_GPU_SCHED_STAT_ENODEV. Any status other than DRM_GPU_SCHED_STAT_ENODEV
signifies that the operation succeeded and the GPU is in a nominal state.
However, to provide more information about the GPU's status, it is needed
to convey more information than just "OK".
Therefore, rename DRM_GPU_SCHED_STAT_NOMINAL to
DRM_GPU_SCHED_STAT_RESET, which better communicates the meaning of this
status. The status DRM_GPU_SCHED_STAT_RESET indicates that the GPU has
hung, but it has been successfully reset and is now in a nominal state
again.
Reviewed-by: Philipp Stanner <phasta@kernel.org>
Link: https://lore.kernel.org/r/20250714-sched-skip-reset-v6-1-5c5ba4f55039@igalia.com
Signed-off-by: Maíra Canal <mcanal@igalia.com>
When the GPU scheduler was ported to using a struct for its
initialization parameters, it was overlooked that panfrost creates a
distinct workqueue for timeout handling.
The pointer to this new workqueue is not initialized to the struct,
resulting in NULL being passed to the scheduler, which then uses the
system_wq for timeout handling.
Set the correct workqueue to the init args struct.
Cc: stable@vger.kernel.org # 6.15+
Fixes: 796a9f55a8 ("drm/sched: Use struct for drm_sched_init() params")
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Closes: https://lore.kernel.org/dri-devel/b5d0921c-7cbf-4d55-aa47-c35cd7861c02@igalia.com/
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250709102957.100849-2-phasta@kernel.org
Add a compatible for the MediaTek MT8370 SoC, with an integrated ARM
Mali G57 MC2 GPU (Valhall-JM, dual core), with new platform data for
its support in the panfrost driver.
It uses the same data as MT8186 for the power management features to
describe power supplies, pm_domains and enablement (one regulator, two
power domains) but also sets the FORCE_AARCH64_PGTABLE flag in the GPU
configuration quirks bitfield to enable AARCH64 4K page table format
mode.
As MT8186 and MT8370 SoC have different GPU architecture (Mali G52 2EE
MC2 for MT8186), making them not compatible, and this mode is only
enabled for Mediatek SoC that are Mali G57 based (compatible with
mediatek,mali-mt8188 or mediatek,mali-8192), having specific platform
data allows to set this flag for MT8370 without modifying MT8186
configuration and behaviour.
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250509-mt8370-enable-gpu-v6-4-2833888cb1d3@collabora.com
In the panfrost driver, the platform data of several Mediatek SoC
declares and uses several different power domains arrays according to
GPU core number present in the SoC:
- mediatek_mt8186_pm_domains (2 cores)
- mediatek_mt8183_pm_domains (3 cores)
- mediatek_mt8192_pm_domains (5 cores)
As they all are fixed arrays, starting with the same entries and the
platform data also has a power domains array length field
(num_pm_domains), they can be replaced by a single array, containing
all entries, if the num_pm_domains field of the platform data is also
set to the matching core number.
So, create a generic power domain array (mediatek_pm_domains) and use
it in the mt8183(b), mt8186, mt8188 and mt8192 platform data instead.
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250509-mt8370-enable-gpu-v6-3-2833888cb1d3@collabora.com
In the panfrost driver, the platform data of several Mediatek SoC
declares and uses custom supplies array definitions
(mediatek_mt8192_supplies, mediatek_mt8183_b_supplies), that are the
same as default_supplies (used by default platform data).
So drop these duplicated definitions and use default_supplies instead.
Also, rename mediatek_mt8183_supplies to a more generic name too
(legacy_supplies).
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250509-mt8370-enable-gpu-v6-2-2833888cb1d3@collabora.com
Commit 64111a0e22 ("drm/panfrost: Fix incorrect updating of current
device frequency") was a Panfrost port of a similar fix in Panthor.
Fix the Panfrost device pointer variable name so that it follows
Panfrost naming conventions.
Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Fixes: 64111a0e22 ("drm/panfrost: Fix incorrect updating of current device frequency")
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250520174634.353267-6-adrian.larumbe@collabora.com
This change is essentially a Panfrost port of commit a3707f53eb
("drm/panthor: show device-wide list of DRM GEM objects over DebugFS").
The DebugFS file is almost the same as in Panthor, minus the GEM object
usage flags, since Panfrost has no kernel-only BO's.
Two additional GEM state flags which are displayed but aren't relevant
to Panthor are 'Purged' and 'Purgeable', since Panfrost implements an
explicit shrinker and a madvise ioctl to flag objects as reclaimable.
Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250520174634.353267-5-adrian.larumbe@collabora.com
Allow UM to label a BO for which it possesses a DRM handle.
Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250520174634.353267-4-adrian.larumbe@collabora.com
Perfcnt samples buffer is not exposed to UM, but we would like to keep
a tag on it as a potential debug aid.
PRIME imported GEM buffers are UM exposed, but since the usual Panfrost
UM driver code path is not followed in their creation, they might remain
unlabelled for their entire lifetime, so a generic tag was deemed
preferable. The tag is assigned before a UM handle is created so it
doesn't contradict the logic about labelling internal BOs.
Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250520174634.353267-3-adrian.larumbe@collabora.com
Functions for labelling UM-exposed an internal BOs are provided. An
example of the latter would be the Perfcnt sample buffer.
This commit is done in preparation of a following one that will allow
UM to set BO labels through a new ioctl().
Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250520174634.353267-2-adrian.larumbe@collabora.com
This will be used in a later commit to trace the drm client_id in
some of the gpu_scheduler trace events.
This requires changing all the users of drm_sched_job_init to
add an extra parameter.
The newly added drm_client_id field in the drm_sched_fence is a bit
of a duplicate of the owner one. One suggestion I received was to
merge those 2 fields - this can't be done right now as amdgpu uses
some special values (AMDGPU_FENCE_OWNER_*) that can't really be
translated into a client id. Christian is working on getting rid of
those; when it's done we should be able to squash owner/drm_client_id
together.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Link: https://lore.kernel.org/r/20250526125505.2360-3-pierre-eric.pelloux-prayer@amd.com
According to Mali manuals, the powerup sequence should be
enable pd, asserting the reset then enabling the clock and
the reverse for powerdown.
Reviewed-by: Steven Price <steven.price@arm.com>
Tested-by: John Williams <porschemad911@gmail.com>
Signed-off-by: Philippe Simons <simons.philippe@gmail.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250403055210.54486-4-simons.philippe@gmail.com
Tie the Allwinner compatible string to the GPU_PM_RT feature bits that will
toggle the clocks and the reset line whenever the power domain is changing
state.
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Philippe Simons <simons.philippe@gmail.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250403055210.54486-3-simons.philippe@gmail.com
When the GPU is the only device attached to a single power domain,
core genpd disable and enable it when gpu enter and leave runtime suspend.
Some power-domain requires a sequence before disabled,
and the reverse when enabled.
Add GPU_PM_RT flag, and implement in
panfrost_device_runtime_suspend/resume.
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Philippe Simons <simons.philippe@gmail.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250403055210.54486-2-simons.philippe@gmail.com
Instead of testing import_attach for imported GEM buffers, invoke
drm_gem_is_imported() to do the test. The helper tests the dma_buf
itself while import_attach is just an artifact of the import. Prepares
to make import_attach optional.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Steven Price <steven.price@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250317131923.238374-9-tzimmermann@suse.de
MediaTek MT8192 SoC has an ARM Mali-G57 MC5 GPU (Valhall-JM). Now that
Panfrost supports AARCH64_4K page table format, let's enable it on this
SoC.
Running glmark2-es2-drm [0] benchmark, reported the same performance
score on both modes Mali LPAE (LEGACY) vs. AARCH64_4K, before and after
this commit. Tested on a Mediatek (MT8395) Genio 1200 EVK board.
[0] https://github.com/glmark2/glmark2
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250324185801.168664-7-ariel.dalessandro@collabora.com
MediaTek MT8188 SoC has an ARM Mali-G57 MC3 GPU (Valhall-JM), which
constantly faults with the current panfrost support.
For instance, running `glmark2-es2-drm` benchmark test:
```
[ 79.617461] panfrost 13000000.gpu: js fault, js=1, status=JOB_BUS_FAULT, head=0xaadc380, tail=0xaadc380
[ 80.119811] panfrost 13000000.gpu: gpu sched timeout, js=0, config=0x7300, status=0x58, head=0xaaca180, tail=0xaaca180, sched_job=000000002fd03ccc
[ 80.129083] panfrost 13000000.gpu: Unhandled Page fault in AS0 at VA 0x0000000000000000
[ 80.129083] Reason: TODO
[ 80.129083] raw fault status: 0x1C2
[ 80.129083] decoded fault status: SLAVE FAULT
[ 80.129083] exception type 0xC2: TRANSLATION_FAULT_2
[ 80.129083] access type 0x1: EXECUTE
[ 80.129083] source id 0x0
```
Note that current panfrost mode (Mali LPAE - LEGACY) only allows to
specify write-cache or implementation-defined as the caching policy,
probably not matching the right configuration. As depicted in the source
code:
drivers/iommu/io-pgtable-arm.c:
```
* MEMATTR: Mali has no actual notion of a non-cacheable type, so the
* best we can do is mimic the out-of-tree driver and hope that the
* "implementation-defined caching policy" is good enough...
```
Now that Panfrost supports AARCH64_4K page table format, let's enable it
on Mediatek MT8188 and configure the cache/shareability policies
properly.
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250324185801.168664-6-ariel.dalessandro@collabora.com
Currently, Panfrost only supports MMU configuration in "LEGACY" (as
Bifrost calls it) mode, a (modified) version of LPAE "Large Physical
Address Extension", which in Linux we've called "mali_lpae".
This commit adds support for conditionally enabling AARCH64_4K page
table format. To achieve that, a "GPU optional quirks" field was added
to `struct panfrost_features` with the related flag.
Note that, in order to enable AARCH64_4K mode, the GPU variant must have
the HW_FEATURE_AARCH64_MMU feature flag present.
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250324185801.168664-5-ariel.dalessandro@collabora.com
Set this feature flag on all Mali Bifrost platforms as the MMU supports
AARCH64 4K page table format.
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250324185801.168664-4-ariel.dalessandro@collabora.com
As done in panthor, define and use these GPU_MMU_FEATURES_* macros,
which makes code easier to read and reuse.
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250324185801.168664-3-ariel.dalessandro@collabora.com
Panfrost does not support uncached mappings, so flag them properly. Also
flag the pages that are mapped as response to a page fault as cached.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250324185801.168664-2-ariel.dalessandro@collabora.com
Use atomic refcount_t helper for pages_use_count to optimize pin/unpin
functions by skipping reservation locking while GEM's pin refcount > 1.
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.d>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250322212608.40511-9-dmitry.osipenko@collabora.com
Add locked and remove unlocked postfixes from drm-shmem function names,
making names consistent with the drm/gem core code.
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.d>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250322212608.40511-6-dmitry.osipenko@collabora.com
Make drm/gem API function names consistent by having locked function
use the _locked postfix in the name, while the unlocked variants don't
use the _unlocked postfix. Rename drm_gem_v/unmap() function names to
make them consistent with the rest of the API functions.
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.d>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250322212608.40511-2-dmitry.osipenko@collabora.com
drm_sched_init() has a great many parameters and upcoming new
functionality for the scheduler might add even more. Generally, the
great number of parameters reduces readability and has already caused
one missnaming, addressed in:
commit 6f1cacf4eb ("drm/nouveau: Improve variable name in
nouveau_sched_init()").
Introduce a new struct for the scheduler init parameters and port all
users.
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Matthew Brost <matthew.brost@intel.com> # for Xe
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> # for Panfrost and Panthor
Reviewed-by: Christian Gmeiner <cgmeiner@igalia.com> # for Etnaviv
Reviewed-by: Frank Binns <frank.binns@imgtec.com> # for Imagination
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com> # for Sched
Reviewed-by: Maíra Canal <mcanal@igalia.com> # for v3d
Reviewed-by: Danilo Krummrich <dakr@kernel.org>
Reviewed-by: Lizhi Hou <lizhi.hou@amd.com> # for amdxdna
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250211111422.21235-2-phasta@kernel.org
The v6.13-rc2 release included a bunch of breaking changes,
specifically the MODULE_IMPORT_NS commit.
Backmerge in order to fix them before the next pull-request.
Include the fix from Stephen Roswell.
Caused by commit
25c3fd1183 ("drm/virtio: Add a helper to map and note the dma addrs and lengths")
Interacting with commit
cdd30ebb1b ("module: Convert symbol namespace to string literal")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://patchwork.freedesktop.org/patch/msgid/20241209121717.2abe8026@canb.auug.org.au
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
We stopped using the driver initialized date in commit 7fb8af6798
("drm: deprecate driver date") and (eventually) started returning "0"
for drm_version ioctl instead.
Finish the job, and remove the unused date member from struct
drm_driver, its initialization from drivers, along with the common
DRIVER_DATE macros.
v2: Also update drivers/accel (kernel test robot)
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Simon Ser <contact@emersion.fr>
Acked-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # msm
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1f2bf2543aed270a06f6c707fd6ed1b78bf16712.1733322525.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The continual trickle of small conversion patches is grating on me, and
is really not helping. Just get rid of the 'remove_new' member
function, which is just an alias for the plain 'remove', and had a
comment to that effect:
/*
* .remove_new() is a relic from a prototype conversion of .remove().
* New drivers are supposed to implement .remove(). Once all drivers are
* converted to not use .remove_new any more, it will be dropped.
*/
This was just a tree-wide 'sed' script that replaced '.remove_new' with
'.remove', with some care taken to turn a subsequent tab into two tabs
to make things line up.
I did do some minimal manual whitespace adjustment for places that used
spaces to line things up.
Then I just removed the old (sic) .remove_new member function, and this
is the end result. No more unnecessary conversion noise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MediaTek MT8188 SoC has a Mali-G57 MC3 GPU and, similarly to
MT8192, it has yet another special GPU ID.
Add the GPU ID to the list and treat it as a standard Mali-G57.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241113112622.123044-1-angelogioacchino.delregno@collabora.com
Commit f11b0417ee ("drm/panfrost: Add fdinfo support GPU load metrics")
retrieves the OPP for the maximum device clock frequency, but forgets to
keep the reference count balanced by putting the returned OPP object. This
eventually leads to an OPP core warning when removing the device.
Fix it by putting OPP objects as many times as they're retrieved.
Also remove an unnecessary whitespace.
Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Fixes: f11b0417ee ("drm/panfrost: Add fdinfo support GPU load metrics")
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241105205458.1318989-1-adrian.larumbe@collabora.com
The current implementation of drm_sched_start uses a hardcoded
-ECANCELED to dispose of a job when the parent/hw fence is NULL.
This results in drm_sched_job_done being called with -ECANCELED for
each job with a NULL parent in the pending list, making it difficult
to distinguish between recovery methods, whether a queue reset or a
full GPU reset was used.
To improve this, we first try a soft recovery for timeout jobs and
use the error code -ENODATA. If soft recovery fails, we proceed with
a queue reset, where the error code remains -ENODATA for the job.
Finally, for a full GPU reset, we use error codes -ECANCELED or
-ETIME. This patch adds an error code parameter to drm_sched_start,
allowing us to differentiate between queue reset and GPU reset
failures. This enables user mode and test applications to validate
the expected correctness of the requested operation. After a
successful queue reset, the only way to continue normal operation is
to call drm_sched_job_done with the specific error code -ENODATA.
v1: Initial implementation by Jesse utilized amdgpu_device_lock_reset_domain
and amdgpu_device_unlock_reset_domain to allow user mode to track
the queue reset status and distinguish between queue reset and
GPU reset.
v2: Christian suggested using the error codes -ENODATA for queue reset
and -ECANCELED or -ETIME for GPU reset, returned to
amdgpu_cs_wait_ioctl.
v3: To meet the requirements, we introduce a new function
drm_sched_start_ex with an additional parameter to set
dma_fence_set_error, allowing us to handle the specific error
codes appropriately and dispose of bad jobs with the selected
error code depending on whether it was a queue reset or GPU reset.
v4: Alex suggested using a new name, drm_sched_start_with_recovery_error,
which more accurately describes the function's purpose.
Additionally, it was recommended to add documentation details
about the new method.
v5: Fixed declaration of new function drm_sched_start_with_recovery_error.(Alex)
v6 (chk): rebase on upstream changes, cleanup the commit message,
drop the new function again and update all callers,
apply the errno also to scheduler fences with hw fences
v7 (chk): rebased
Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com>
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240826122541.85663-1-christian.koenig@amd.com
Extend the uAPI with a new job requirement flag for cycle
counters. This requirement is used by userland to indicate that a job
requires cycle counters or system timestamp to be propagated. (for use
with write value timestamp jobs)
We cannot enable cycle counters unconditionally as this would result in
an increase of GPU power consumption. As a result, they should be left
off unless required by the application.
If a job requires cycle counters or system timestamps propagation, we
must enable cycle counting before issuing a job and disable it right
after the job completes.
Since this extends the uAPI and because userland needs a way to advertise
features like VK_KHR_shader_clock conditionally, we bumps the driver
minor version.
v2:
- Rework commit message
- Squash uAPI changes and implementation in this commit
- Simplify changes based on Steven Price comments
v3:
- Add Steven Price r-b
- Fix a codestyle issue
Signed-off-by: Mary Guillemard <mary.guillemard@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240819080224.24914-3-mary.guillemard@collabora.com
Expose system timestamp and frequency supported by the GPU.
Mali uses an external timer as GPU system time. On ARM, this is wired to
the generic arch timer so we wire cntfrq_el0 as device frequency.
This new uAPI will be used in Mesa to implement timestamp queries and
VK_KHR_calibrated_timestamps.
v2:
- Rewrote to use GPU timestamp register
- Add missing include for arch_timer_get_cntfrq
- Rework commit message
v3:
- Move panfrost_cycle_counter_get and panfrost_cycle_counter_put to
panfrost_ioctl_query_timestamp
- Handle possible overflow in panfrost_timestamp_read
Signed-off-by: Mary Guillemard <mary.guillemard@collabora.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240819080224.24914-2-mary.guillemard@collabora.com
This was basically just another one of amdgpus hacks. The parameter
allowed to restart the scheduler without turning fence signaling on
again.
That this is absolutely not a good idea should be obvious by now since
the fences will then just sit there and never signal.
While at it cleanup the code a bit.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722083816.99685-1-christian.koenig@amd.com
Panfrost DRM driver uses devfreq to perform DVFS, while using simple_ondemand
devfreq governor by default. This causes driver initialization to fail on
boot when simple_ondemand governor isn't built into the kernel statically,
as a result of the missing module dependency and, consequently, the required
governor module not being included in the initial ramdisk. Thus, let's mark
simple_ondemand governor as a softdep for Panfrost, to have its kernel module
included in the initial ramdisk.
This is a rather longstanding issue that has forced distributions to build
devfreq governors statically into their kernels, [1][2] or has forced users
to introduce some unnecessary workarounds. [3]
For future reference, not having support for the simple_ondemand governor in
the initial ramdisk produces errors in the kernel log similar to these below,
which were taken from a Pine64 RockPro64:
panfrost ff9a0000.gpu: [drm:panfrost_devfreq_init [panfrost]] *ERROR* Couldn't initialize GPU devfreq
panfrost ff9a0000.gpu: Fatal error during GPU init
panfrost: probe of ff9a0000.gpu failed with error -22
Having simple_ondemand marked as a softdep for Panfrost may not resolve this
issue for all Linux distributions. In particular, it will remain unresolved
for the distributions whose utilities for the initial ramdisk generation do
not handle the available softdep information [4] properly yet. However, some
Linux distributions already handle softdeps properly while generating their
initial ramdisks, [5] and this is a prerequisite step in the right direction
for the distributions that don't handle them properly yet.
[1] https://gitlab.manjaro.org/manjaro-arm/packages/core/linux/-/blob/linux61/config?ref_type=heads#L8180
[2] https://salsa.debian.org/kernel-team/linux/-/merge_requests/1066
[3] https://forum.pine64.org/showthread.php?tid=15458
[4] https://git.kernel.org/pub/scm/utils/kernel/kmod/kmod.git/commit/?id=49d8e0b59052999de577ab732b719cfbeb89504d
[5] 97ac4d37aa
Cc: Diederik de Haas <didi.debian@cknow.org>
Cc: Furkan Kardame <f.kardame@manjaro.org>
Cc: stable@vger.kernel.org
Fixes: f3ba91228e ("drm/panfrost: Add initial panfrost driver")
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/4e1e00422a14db4e2a80870afb704405da16fd1b.1718655077.git.dsimic@manjaro.org
MediaTek MT8188 has a Mali-G57 MC3 (Valhall-JM): add a new
compatible and platform data using the same supplies and the
same power domain lists as MT8183 (one regulator, three power
domains).
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240611085602.491324-3-angelogioacchino.delregno@collabora.com
When Panfrost must pin an object that is being prepared a dma-buf
attachment for on behalf of another driver, the core drm gem object pinning
code already takes a lock on the object's dma reservation.
However, Panfrost GEM object's pinning callback would eventually try taking
the lock on the same dma reservation when delegating pinning of the object
onto the shmem subsystem, which led to a deadlock.
This can be shown by enabling CONFIG_DEBUG_WW_MUTEX_SLOWPATH, which throws
the following recursive locking situation:
weston/3440 is trying to acquire lock:
ffff000000e235a0 (reservation_ww_class_mutex){+.+.}-{3:3}, at: drm_gem_shmem_pin+0x34/0xb8 [drm_shmem_helper]
but task is already holding lock:
ffff000000e235a0 (reservation_ww_class_mutex){+.+.}-{3:3}, at: drm_gem_pin+0x2c/0x80 [drm]
Fix it by replacing drm_gem_shmem_pin with its locked version, as the lock
had already been taken by drm_gem_pin().
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Steven Price <steven.price@arm.com>
Fixes: a780278472 ("drm/gem: Acquire reservation lock in drm_gem_{pin/unpin}()")
Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240523113236.432585-2-adrian.larumbe@collabora.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmYlapoeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGJLgH/RFrsXefpxAWACJv
wRmIx/YFjI3Z4nypBZPXysX/JOuf/cf4bR22jMHC1vhQDtxVgB7eUpEYx0C0Y5RD
ll7cunAZCpP+PB725/bOWbaF94eigl8xC4RrKPon4tG1CS9NAvCJFDyNgWpqh48s
sSKKae68a16zMtIX5Za8nvmsBQOeD67ZFBgI4m7wIDDhTXY3XlG84r8Rz/ZwcdE/
rExFkDMUqjpoJVAMBtETQNk4pvKZVMrW2B0f/xZSR+IKXw5l2FO0raXkIG/6TERs
CxJvCuUjKIosqFLIK2O/cU9G+5V2axZ/WD8YRwDr2vlnnOPht+dFQzyPcuSqezbG
ShIhQo8=
=GI5F
-----END PGP SIGNATURE-----
Backmerge tag 'v6.9-rc5' into drm-next
Linux 6.9-rc5
I've had a persistent msm failure on clang, and the fix is in fixes
so just pull it back to fix that.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Subject: [PATCH] drm/panfrost: Fix the error path in
panfrost_mmu_map_fault_addr()
If some the pages or sgt allocation failed, we shouldn't release the
pages ref we got earlier, otherwise we will end up with unbalanced
get/put_pages() calls. We should instead leave everything in place
and let the BO release function deal with extra cleanup when the object
is destroyed, or let the fault handler try again next time it's called.
Fixes: 187d292920 ("drm/panfrost: Add support for GPU heap allocations")
Cc: <stable@vger.kernel.org>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Co-developed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240105184624.508603-18-dmitry.osipenko@collabora.com
Increase the timeout value to prevent system logs on Amlogic boards flooding
with power transition warnings:
[ 13.047638] panfrost ffe40000.gpu: shader power transition timeout
[ 13.048674] panfrost ffe40000.gpu: l2 power transition timeout
[ 13.937324] panfrost ffe40000.gpu: shader power transition timeout
[ 13.938351] panfrost ffe40000.gpu: l2 power transition timeout
...
[39829.506904] panfrost ffe40000.gpu: shader power transition timeout
[39829.507938] panfrost ffe40000.gpu: l2 power transition timeout
[39949.508369] panfrost ffe40000.gpu: shader power transition timeout
[39949.509405] panfrost ffe40000.gpu: l2 power transition timeout
The 2000 value has been found through trial and error testing with devices
using G52 and G31 GPUs.
Fixes: 22aa1a2090 ("drm/panfrost: Really power off GPU cores in panfrost_gpu_power_off()")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240322164525.2617508-1-christianshewitt@gmail.com
If job accounting is disabled, then both fdinfo's drm-engine and drm-cycle
key values will remain immutable. In that case, it makes more sense not to
display them at all to avoid confusing user space profiling tools.
Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240316231306.293817-1-adrian.larumbe@collabora.com
Debugfs isn't always available in production builds that try to squeeze
every single byte out of the kernel image, but we still need a way to
toggle the timestamp and cycle counter registers so that jobs can be
profiled for fdinfo's drm engine and cycle calculations.
Drop the debugfs knob and replace it with a sysfs file that accomplishes
the same functionality, and document its ABI in a separate file.
Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240306015819.822128-2-adrian.larumbe@collabora.com
