This driver uses the enable-gpios property and it is confusing that the
error message refers to reset-gpios. Use the correct name when the
enable GPIO is not found.
Fixes: e2450d32e5 ("drm/panel: ili9882t: Break out as separate driver")
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250217120428.3779197-1-jkeeping@inmusicbrands.com
Consensus on the mailing lists is that panels shouldn't use a table of
init commands but should instead use init functions. With the recently
introduced mipi_dsi_dcs_write_seq_multi() this is not only clean/easy
but also saves space. Measuring before/after this change:
$ scripts/bloat-o-meter \
.../before/panel-ilitek-ili9882t.ko \
.../after/panel-ilitek-ili9882t.ko
add/remove: 3/2 grow/shrink: 0/2 up/down: 6834/-8177 (-1343)
Function old new delta
starry_ili9882t_init - 6152 +6152
starry_ili9882t_init.d - 678 +678
ili9882t_disable.d - 4 +4
ili9882t_disable 260 228 -32
ili9882t_prepare 540 396 -144
.compoundliteral 681 - -681
starry_ili9882t_init_cmd 7320 - -7320
Total: Before=11928, After=10585, chg -11.26%
Let's do the conversion.
Since we're touching all the tables, let's also convert hex numbers to
lower case as per kernel conventions.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20240514102056.v5.8.I407b977f9508573103491df549dfaffc3688db13@changeid
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240514102056.v5.8.I407b977f9508573103491df549dfaffc3688db13@changeid
At present, we have found that there may be a problem of blurred
screen during fast sleep/resume. The direct cause of the blurred
screen is that the IC does not receive 0x28/0x10. Because of the
particularity of the IC, before the panel enters sleep hid must
stop scanning, as i2c_hid_core_suspend before ili9882t_disable.
If move the ili9882t_enter_sleep_mode function to ili9882t_unprepare,
touch reset will pull low before panel entersleep, which does not meet
the timing requirements.. So in order to solve this problem, the IC
can handle it through the exception mechanism when it cannot receive
0x28/0x10 command. Handling exceptions requires a reset 50ms delay.
Refer to vendor detailed analysis [1].
Ilitek vendor also suggested switching the page before entering sleep to
avoid panel IC not receiving 0x28/0x10 command.
Note: 0x28 is display off, 0x10 is sleep in.
[1]: https://github.com/ILITEK-LoganLin/Document/tree/main/ILITEK_Power_Sequence
Signed-off-by: Cong Yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231013091844.804310-3-yangcong5@huaqin.corp-partner.google.com
The Starry ILI9882t-based panel should never have been part of the boe
tv101wum driver, it is clearly based on the Ilitek ILI9882t display
controller and if you look at the custom command sequences for the
panel these clearly contain the signature Ilitek page switch (0xff)
commands. The hardware has nothing in common with the other panels
supported by this driver.
Break this out into a separate driver and config symbol instead.
If the placement here is out of convenience for using similar code,
we should consider creating a helper library instead.
Co-developed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Cong Yang <yangcong5@huaqin.corp-partner.google.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231013091844.804310-2-yangcong5@huaqin.corp-partner.google.com
