Hook up drm_panel support in the omapdrm driver. The change is
relatively simply as the way has been paved by drm_bridge support
already. In addition to looking up, attaching to and detaching from the
panel, we only need to add panel support in the connector .get_modes()
handler, take connector bus flags (set by the panel) into account, and
enable/disable the panel in the encoder enable/disable operations
handlers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Hook up drm_bridge support in the omapdrm driver. Despite the recent
extensive preparation work, this is a rather intrusive change, as the
management of outputs needs to be adapted through the driver to handle
both omap_dss_device and drm_bridge.
Connector creation is skipped when using a drm_bridge, as the bridge
creates the connector internally. This creates issues with systems that
split connector operations (such as modes retrieval and hot-plug
detection) across different bridges. These systems can't be supported
using drm_bridge for now (their support through the omap_dss_device
infrastructure is not affected), this will be fixed in subsequent
changes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DRM_BUS_FLAG_PIXDATA_(POS|NEG)EDGE and
DRM_BUS_FLAG_SYNC_(POS|NEG)EDGE flags are deprecated in favour of the
new DRM_BUS_FLAG_PIXDATA_(DRIVE|SAMPLE)_(POS|NEG)EDGE and
new DRM_BUS_FLAG_SYNC_(DRIVE|SAMPLE)_(POS|NEG)EDGE flags. Replace them
through the code.
This effectively changes the value of the .sampling_edge bridge timings
field in the dumb-vga-dac driver. This is safe to do as no driver
consumes these values yet.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_dss_device type and output_type fields differ mostly for
historical reasons. The output_type field is required for all devices
but the display at the end of the pipeline, and must be set to
OMAP_DISPLAY_TYPE_NONE for the latter. The type field is required for
all devices but the internal encoder, for which it is ignored.
The only reason why the output_type field must be set to
OMAP_DISPLAY_TYPE_NONE for the display at the end of the pipeline is to
identify omap_dss_device instances corresponding to displays. This is
not documented and confusing.
Clean the code by adding a new display field to the omap_dss_device
structure to identify displays, and merge the type and output_type
fields.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that the direction of OF graph walk has been reversed, there's no
need to lookup devices by port as we have no sink device connected
through multiple sink ports. Simplify OF lookup of the DSS devices to
look them up by node only.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DPI and SDI encoders store the full videomode upon mode set, to only
use the value of the pixel clock when enabling the encoder. This wastes
memory. Store the pixel clock value only.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Replace internal usage of struct videomode with struct drm_display_mode
in order to avoid converting needlessly between the data structures.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_dss_device .check_timings() and .set_timings() operations
operate on struct videomode, while the DRM API operates on struct
drm_display_mode. This forces conversion from to videomode in the
callers. While that's not a problem per se, it creates a difference with
the drm_bridge API.
Replace the videomode parameter to the .check_timings() and
.set_timings() operations with a drm_display_mode. This pushed the
conversion to videomode down to the DSS devices in some cases. If needed
they will be converted to operate on drm_display_mode natively.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The mode setting handler of the VENC stores the video mode internally,
to then convert it to a configuration when programming the hardware. The
stored mode is otherwise unused. Cache the configuration directly
instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The field is only used to check whether the device is connected, and we
can do so by checking the dss field instead. Remove the src field.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DT bindings for the OMAP DSS allow assigning numerical IDs to
display outputs through display entries in the alias node. The driver
uses this information to sort pipelines according to the order specified
in DT, making it possible for a system to give a priority order to
outputs.
Retrieval of the alias ID is done when initializing display dss devices.
That code will be removed when moving to drm_bridge and drm_panel. Move
retrieval of the alias ID to display pipeline connection time and store
it in the pipeline structure instead to keep the feature.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The TV encoder supports both PAL and NTSC modes, but when queried for
the list of modes it supports, only the currently selected mode is
reported. Fix it and report the two modes unconditionally.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of manually iterating over the dss devices in the pipeline to
find the first one that implements the .get_modes() operation, add a new
operation flag for .get_modes() and use the omap_connector_find_device()
helper function to locate the right dss device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that the .get_modes() operations takes a drm_connector and fills it
with modes, it becomes easy to fill display information in the same
operation without requiring a separate .get_size() opearation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_dss_device operations expose fixed video timings through a
.get_timings() operation that return a single timing for the device. To
prepare for the move to drm_bridge, modify the API to instead add DRM
modes directly to the connector.
As this puts more burden on display devices, we also create a helper
function for panels to add a single DRM mode from the panel video
timings.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
All the internal encoders share common init and cleanup code. Factor it
out to separate functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The field is only used in a safety check during device
connection/disconnection, where the src field can be easily used
instead. Remove it and use src.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdrm and omapdss drivers are architectured based on display
pipelines made of multiple components handled from sink (display) to
source (DSS output). This is incompatible with the DRM bridge and panel
APIs that handle components from source to sink.
Reconcile the omapdrm and omapdss drivers with the DRM bridge and panel
model by reversing the direction of the DSS device .enable() and
.disable() operations. This completes the move to the DRM bridge model,
with the notable exception of the DSI pipelines that will require more
work.
We also adapt the omapdss shutdown handler dss_shutdown() to shut down
all active pipelines starting from the pipeline output device instead of
the display device.
As a consequence the for_each_dss_display() macro isn't used and can be
removed, and the omapdss_device_get_next() function underlying the macro
can be simplified to search for output devices only.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The displays (connectors, panels and encoders) return an error from
their .enable() handler when the dss device is not connected. They also
disconnect the dss device explicitly from their .remove() handler if it
is still connected.
Those safety checks are not needed:
- The .enable() handler is called from code paths that access the dss
devices chain from the display device, which is set to NULL when the
device isn't connected.
- The .remove() handler can only be called when unloading the module as
the driver has the suppress_bind_attrs attribute set, and a reference
to the module is taken when constructing the dss devices chain, so the
module can only be unloaded when the dss device is disconnected.
Remove the safety checks.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The internal encoders return an error from their .enable() handler when
their are not connected to a dss manager. As the flag used is set and
cleared in the connect and disconnect handlers, this effectively checks
whether the omap_dss_device is connected.
The .enable() handler is called from code paths that access the dss
devices chain from the display device, which is set to NULL when the
device isn't connected, making it impossible to access the device in
that case.
The safety check is thus not needed, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of rolling out custom suspend/resume implementations based on
state information stored in the driver's data structures, use the atomic
suspend/resume helpers that rely on a DRM atomic state object.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The venc_device structure wss_data field is set to 0 and never otherwise
modified, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The kobj field from struct omap_dss_device is not used. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Since commit b4935e3a3c ("drm/omap: Store bus flags in the
omap_dss_device structure") video mode flags are managed by the omapdss
(and later omapdrm) core based on bus flags stored in omap_dss_device.
This works fine for all devices whose video modes are set by the omapdss
and omapdrm core, but breaks DSI operation as the DSI still uses legacy
code paths and sets the DISPC timings manually.
To fix the problem properly we should move the DSI encoder to the new
encoder model. This will however require a considerable amount of work.
Restore DSI operation by adding back video mode flags handling in the
DSI encoder driver as a hack in the meantime.
Fixes: b4935e3a3c ("drm/omap: Store bus flags in the omap_dss_device structure")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190111035120.20668-5-laurent.pinchart@ideasonboard.com
Commit edb715dffd ("drm/omap: dss: dsi: Move initialization code from
bind to probe") moved the of_platform_populate() call from dsi_bind() to
dsi_probe(), but failed to move the corresponding
of_platform_depopulate() from dsi_unbind() to dsi_remove(). This results
in OF child devices being potentially removed multiple times. Fix it by
placing the of_platform_depopulate() call where it belongs.
Fixes: edb715dffd ("drm/omap: dss: dsi: Move initialization code from bind to probe")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190111035120.20668-4-laurent.pinchart@ideasonboard.com
Reading any of the DSI debugfs files results in a crash, as wrong
pointer is passed to the dump functions, and the dump functions use a
wrong pointer. This patch fixes DSI debug dumps.
Fixes: f3ed97f9ae ("drm/omap: dsi: Simplify debugfs implementation")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190111035120.20668-3-laurent.pinchart@ideasonboard.com
After the changes from 4.20 the DSI encoder tries to find the
attached panel before populating the DSI bus. If the panel is
not found -EPROBE_DEFER is returned, so the DSI bus is never
populated and the panel never added.
Fix this by populating the DSI bus before searching for the
video sink in dsi_init_output().
Fixes: 27d624527d ("drm/omap: dss: Acquire next dssdev at probe time")
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121160916.22017-3-sebastian.reichel@collabora.com
panel-dpi used to convey the bus-flags via the videomode, but recent
changes changed the use of videomode to DRM's drm_display_mode which
does not contain bus-flags. This broke panel-dpi, which didn't
explicitly store the bus-flags into dssdev->bus_flags.
Fix this by setting dssdev->bus_flags. Also change the bus_flags type to
u32, as that is the type used in the DRM framework, and we would get a
warning with drm_bus_flags_from_videomode() otherwise.
Fixes: 3fbda31e81 ("drm/omap: Split mode fixup and mode set from encoder enable")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181126092447.11864-1-tomi.valkeinen@ti.com
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We're missing a call to of_platform_depopulate() on errors for dsi.
Looks like dss is already doing this.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106152802.38599-1-tony@atomide.com
The internal encoders (DSI, HDMI4, HDMI5 and VENC) runtime PM handlers
attempt to manage the runtime PM state of the connected DISPC, based on
the rationale that the DISPC providing data to the encoders requires
ensuring that the display is active whenever the encoders are active.
While the DISPC provides data to the encoders, it doesn't as such
constitute a resource that encoders require in order to be taken out
of suspend, contrary to for instance a functional clock or a power
supply. Encoders registers can be accessed without the DISPC being
active, and while the encoders will not output any video stream without
being fed by the DISPC, the DISPC PM state doesn't influence the
encoders PM state.
For this reason the DISPC PM state is better managed from the omapdrm
driver, in the CRTC enable and disable operations. This allows the
encoders PM state to be handled separately from the DISPC, and in
particular at times when the DISPC may not be available (for instance at
probe due to the DSS probe being deferred, or at remove time du to the
DISPC being already removed).
Fixes: edb715dffd ("drm/omap: dss: dsi: Move initialization code from bind to probe")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181110111654.4387-5-laurent.pinchart@ideasonboard.com
The probe function performs hardware access to read the number of
supported data lanes from a configuration register and thus requires the
device to be active. Ensure this by surrounding the access with
dsi_runtime_get() and dsi_runtime_put() calls.
Fixes: edb715dffd ("drm/omap: dss: dsi: Move initialization code from bind to probe")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181110111654.4387-4-laurent.pinchart@ideasonboard.com
The bind function performs hardware access (in hdmi4_cec_init()) and
thus requires the device to be active. Ensure this by surrounding the
bind function by hdmi_runtime_get() and hdmi_runtime_put() calls.
Fixes: 27d624527d ("drm/omap: dss: Acquire next dssdev at probe time")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181110111654.4387-3-laurent.pinchart@ideasonboard.com
The DSS DT node contains children that describe the DSS components
(DISPC and internal encoders). Each of those components is handled by a
platform driver, and thus needs to be backed by a platform device.
The corresponding platform devices are created in mach-omap2 code by a
call to of_platform_populate(). While this approach has worked so far,
it doesn't model the hardware architecture very well, as it creates
child devices before the parent is ready to handle them. This would be
akin to creating I2C slaves before the I2C master is available.
The task can be easily performed in the omapdss driver code instead,
simplifying mach-omap2 code. We however can't remove the mach-omap2 code
completely as the omap2fb driver still depends on it, but we can move it
to the omap2fb-specific section, where it can stay until the omap2fb
driver gets removed.
This has the added benefit of not allowing DSS components to probe
before the DSS itself, which led to runtime PM issues when the DSS probe
is deferred.
Fixes: 27d624527d ("drm/omap: dss: Acquire next dssdev at probe time")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181110111654.4387-2-laurent.pinchart@ideasonboard.com
drm_format_info table has a field 'is_yuv' to denote if the format
is yuv or not. The driver is expected to use this instead of
having a function for the same purpose.
Signed-off-by: Ayan Kumar halder <ayan.halder@arm.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/omapdrm/dss/dispc.c: In function 'dispc_ovl_setup_common':
drivers/gpu/drm/omapdrm/dss/dispc.c:2627:19: warning:
variable 'frame_height' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We prefer to use ERR_CAST to do so.
The issue is detected with the help of Coccinelle.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of calling the .set_timings() operation recursively from the
display device backwards, iterate over the devices manually in the DRM
encoder code. This moves the complexity to a single central location and
simplifies the logic in omap_dss_device drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The video timings are stored in the CRTC structure by the
omap_crtc_dss_set_timings() function, called by dss_mgr_set_timings()
from the .enable() operation of the internal encoders. This instead
belongs to the .set_timings() code paths. Move the
omap_crtc_dss_set_timings() calls accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The VENC encoder modifies the requested video mode to match the NTSC or
PAL timings (or reject the video mode completely) in the .set_timings()
operation. This should be performed in the .check_timings() operation
instead. Move the fixup.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The SDI encoder modifies the pixel clock of the requested video mode to
take the limitations of the PLL into account in the .enable() operation.
This should be performed in the .check_timings() operation instead. Move
the fixup.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Constify many pointers to struct videomode, as well as pointers to
container structures, to ensure the video mode isn't modified after
the .check_timings() operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSI encoder modifies the passed videomode to take the requirements
of the internal DISPC-DSI bus into account in the .enable_video_output()
operation. This should be performed in the .check_timings() operation
instead. There is however no .check_timings() operation as the DSI
encoder uses a custom API, so move it to the closest match which is the
.set_config() operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The video mode is aleady fixed up by the .check_timings() operation,
there's no need to repeat that when enabling the DPI output.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of call the dispc timings check function dispc_mgr_timings_ok()
from the internal encoders .check_timings() operation, expose it through
the dispc ops (after renaming it to check_timings) and call it directly
from omapdrm. This allows removal of now empty omap_dss_device
.check_timings() operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Timings for the TV output are currently reported by the analog TV
connector. This has the disadvantage of having to handle timing-related
operations in a connector omap_dss_device that has, at the hardware
level, no knowledge of any timing information.
Implement the .get_timings() operation in the venc driver, and get
timings from the first component in the pipeline that implements the
operatation. This switches the duty of reporting analog TV timings from
the connector to the encoder.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Source components in the display pipeline need to configure their output
signals polarities and clock driving edge based on the requirements of
the sink component.
Those requirements are currently shared across the whole pipeline in the
flags of a videomode structure, instead of being local to each bus. This
both prevents multiple buses from having different configurations (when
the hardware supports it), and makes it difficult to move from videomode
to drm_display_mode as the latter doesn't contain bus polarities and
clock edge flags.
Add a bus_flags field to the omap_dss_device structure and move the
DISPLAY_FLAGS_DE_(LOW|HIGH), DISPLAY_FLAGS_PIXDATA_(POS|NEG)EDGE and
DISPLAY_FLAGS_SYNC_(POS|NEG)EDGE videomode flags to bus_flags in all
external encoders, connectors and panels. The videomode flags are still
used internally for internal encoders, this will be addressed in a
second step.
The related videomode flags in the default mode of the DVI connector can
simply be dropped, as they are always overridden by the TFP410 driver.
Note that this results in both the DISPLAY_FLAGS_SYNC_POSEDGE and
DISPLAY_FLAGS_SYNC_NEGEDGE flags being set, which is invalid, but only
the former is tested for when programming the DISPC, so the DVI
connector flags are effectively overridden by the TFP410 flags.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The .set_timings() operations of the omap_dss_device instances don't
need to modify the passed timings. Make the pointer const.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The two functions implement the .set_timings() and .check_timings()
operations. Rename them to hdmi_disply_set_timings() and
hdmi_display_check_timings() respectively to match the operations names
and make searching the source code easier.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of calling the EDID read operation (.read_edid()) recursively
from the display device back to the first device that provides EDID read
support, iterate over the devices manually in the DRM connector code.
This moves the complexity to a single central location and simplifies
the logic in omap_dss_device drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_dss_device .enable_hpd() and .disable_hpd() are used to enable
and disable hot-plug detection at omapdrm probe and remove time. This is
required to avoid reporting hot-plug detection events before the DRM
infrastructure is ready to accept them, as that could result in crashes
or other malfunction.
Hot-plug event reporting is conditioned by both HPD being enabled
through the .enable_hpd() operation and by the HPD callback being
registered though the .register_hpd_cb() operation. We thus don't need a
separate enable operation if we can guarantee that callbacks won't be
registered too early.
HPD callbacks are registered at connector initialization time, which is
too early to start reporting HPD events. There's however nothing
blocking a move of callback registration to a later time when the
omapdrm driver calls the HPD enable operations. Do so, and remove the
HPD enable operation completely from omap_dss_device drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The HPD-related omap_dss_device operations are now only called when the
device supports HPD. There's no need to duplicate that check in the
omap_dss_device drivers. The .register_hpd_cb() operation can as a
result be turned into a void operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When an omap_dss_device operation can be implemented in multiple places
in a chain of devices, it is important to find out which device to
address to perfom the operation. This is currently done by calling the
operation on the display device at the end of the chain, and recursively
delagating the operation to the previous device if it can't be performed
locally. The drawback of this approach is an increased complexity in
omap_dss_device drivers.
In order to simplify the drivers, we will switch from a recursive model
to an interative model, centralizing the complexity in a single
location. This requires knowing which operations an omap_dss_device
supports at runtime. We can already test which operations are
implemented by checking the operation pointer, but implemented
operations can require resources whose availability varies between
systems. For instance a hot-plug signal from a connector can be wired to
a GPIO or to a bridge chip.
Add operation flags that can be set in the omap_dss_device structure by
drivers to signal support for operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_dss_device instances have two ops structures, omap_dss_driver and
omap_dss_device_ops. The former is used for devices at the end of the
pipeline (a.k.a. display devices), and the latter for intermediate
devices.
Having two sets of operations isn't convenient as code that iterates
over omap_dss_device instances need to take them both into account.
There's currently a reasonably small amount of such code, but more will
be introduced to move the driver away from recursive operations. To
simplify current and future code, move all operations that are not
specific to the display device to the omap_dss_device_ops.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Various functions that need to differentiate between omap_dss_device
instances corresponding to displays and to internal encoders use the
omap_dss_device.driver field, which is only set for display instances.
This gets in the way of the omap_dss_device operations refactoring.
Replace that with a check based on the output_type field which is set
for all omap_dss_device instances but displays.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdrm driver checks at suspend and resume time whether the
displays it operates on have their driver operations set. This check is
unneeded, as all display drivers set the driver operations field at
probe time and never touch it afterwards. This is furthermore proven by
the dereferencing of the driver field without checking it first in
several locations.
The omapdss driver performs a similar check at shutdown time. This is
unneeded as well, as the for_each_dss_display() macro it uses to iterate
over displays locates the displays by checking the driver field
internally.
As those checks are unnecessary, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The .get_mirror() and .set_mirror() omap_dss_driver operations are
implemented by the panel-tpo-td043mtea1 driver but are never used.
Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The .probe(), .remove(), .run_test(), .get_rotate() and .set_rotate()
omap_dss_driver operations are not used. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The dss_mgr .connect() and .disconnect() are implemented as no-op in
omapdrm. The operations are unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_dss_device.dispc_channel_connect field is used by DSS outputs
to fail the .enable() operation if they're not connected. Set the field
directly from the (dis)connect handlers of the DSS outputs instead of
going through the CRTC dss_mgr operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The CRTC connect handler checks whether the DSS output supports the
DISPC channel assigned to it. As the channel is assigned to the output
by the output driver a failure there could only result from a driver
bug. All the output drivers have been verified and they are always
assigned a DISPC channel that is supported on the SoC they run on. The
check can thus be removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Replace the dss display device pointer by a pipe pointer that will allow
the omap_crtc_init() function to access both the display and the DSS
output. As a result we can remove the omapdss_device_get_dispc_channel()
function that is now unneeded.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
To simplify the pipeline disconnection handling merge the
omapdss_device_disconnect() and omapdss_output_unset_device() functions.
The device state check is now called for every device in the pipeline,
extending this sanity check coverage.
There is no need to return an error from omapdss_device_disconnect()
when the check fails, as omapdss_output_unset_device() used to do, given
that we can't prevent disconnection due to device unbinding (the return
value of omapdss_output_unset_device() is never checked in the current
code for that reason).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The display type is validated when the display is connected to the DSS
output. We already have all the information we need for validation when
initializing the outputs. Move validation to output initialization to
simplify pipeline connection handling.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When a DSS output is (dis)connected the omapdss_output_(un)set_device()
function performs a sanity check to ensure that the output isn't already
(dis)connected. The check is unnecessary as those situations should
never happen, but can nonetheless be useful to catch driver bugs. To
prepare for removal of the omapdss_output_(un)set_device() functions
move the connection check to the omapdss_device_connect() function. The
omapdss_device_disconnect() already contains a corresponding check.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdrm and omapdss drivers are architectured based on display
pipelines made of multiple components handled from sink (display) to
source (DSS output). This is incompatible with the DRM bridge and panel
APIs that handle components from source to sink.
To reconcile the omapdrm and omapdss drivers with the DRM bridge and
panel model, we need to reverse the direction of the DSS device
operations. Start with the connect and disconnect operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Regulators for the DPI, DSI, HDMI, SDI and VENC outputs are all looked
up when connecting the output omap_dss_device. There's no need to delay
regulator handling to that time, get the regulators at probe time.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The dss_mgr_connect() and dss_mgr_disconnect() functions take two
omap_dss_device pointers as parameters, which are always set to the same
value by all callers. Remove the duplicated pointer.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add a new omapdss_display_get() function to retrieve the omap_dss_device
for a given DSS output. This will be used when reversing the direction
of the DSS pipeline handling logic.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Similarly to for_each_dss_display(), the for_each_dss_output() macro
iterates over all the DSS connected outputs.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Look up the next dssdev at probe time based on device tree links for all
DSS outputs and encoders. This will be used to reverse the order of the
dssdev connect and disconnect call chains.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There's no reason to delay initialization of most of the driver (such as
mapping memory I/O or enabling runtime PM) to the component bind
handler. Perform as much of the initialization as possible at probe
time, initializing at bind time only the parts that depends on the DSS.
The cleanup code is moved from unbind to remove in a similar way.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There's no reason to delay initialization of most of the driver (such as
mapping memory I/O or enabling runtime PM) to the component bind
handler. Perform as much of the initialization as possible at probe
time, initializing at bind time only the parts that depends on the DSS.
The cleanup code is moved from unbind to remove in a similar way.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There's no reason to delay initialization of most of the driver (such as
mapping memory I/O or enabling runtime PM) to the component bind
handler. Perform as much of the initialization as possible at probe
time, initializing at bind time only the parts that depends on the DSS.
The cleanup code is moved from unbind to remove in a similar way.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There's no reason to delay initialization of most of the driver (such as
mapping memory I/O or enabling runtime PM) to the component bind
handler. Perform as much of the initialization as possible at probe
time, initializing at bind time only the parts that depends on the DSS.
The cleanup code is moved from unbind to remove in a similar way.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Rename the jump labels according to the cleanup they perform, not the
location they're accessed from, and move functions from error checks to
cleanup paths, and move reference handling to simplify cleanup.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdss_of_find_source_for_first_ep() function locates the source
corresponding to the first endpoint of the first port of a device node.
We can easily extend it to locate sinks as well by passing the port
number as a parameter. This will be useful to find sinks in encoders
drivers.
Extend the function and rename it to omapdss_of_find_connected_device()
to reflect its new extended purpose.
Additionally, it is useful to differentiate between failures to return
the connected device because no link exists in the device tree for the
requested port, or because the connected device as described in the
device tree is invalid or not probed yet. Return NULL in the first case
and an error code in the second case, and update the callers
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_dss_device port_num field stores the DT port number associated
with the device. The field is used in different ways depending on the
device type:
- For DPI outputs, the port number is used as an identifier of the DPI
instance
- For sources, the port number is used to look up the omap_dss_device by
DT port node
As omap_dss_device instances are only looked up as sources by sinks,
setting the field to the number of the source port works for both use
cases.
However, to enable looking up sinks, we need to record all the ports
associated with an omap_dss_device. Do so by turning the port_num field
into an of_ports bitmask. For DPI outputs the port number is
additionally stored in the dpi_data structure as the output ID.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdss_find_output_from_display() function is only used to retrieve
the dispc channel corresponding to the display. Return the dispc channel
directly, and rename the function to omapdss_device_get_dispc_channel()
to match its new purpose.
The dssdev->id check is removed as the dssdev is guaranteed to be an
output and have a non-zero id, as proved by the lack of crash despite
the caller never checking the returned pointer before dereferencing it.
As the function is not specific to outputs anymore, move it from
output.c to base.c.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSS manager ops and private data pointer are specific to a DSS
instance. Store them in the dss_device structure instead of global
variable.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Storing the dss_device pointer in the omap_dss_device structure will
allow accessing the dss_device from the dss_mgr API functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The functions operate on any omap_dss_device, move them from display.c
to base.c. While at it rename them to match the naming of the other
functions operating on struct omap_dss_device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The panel devices list isn't used anymore, all panel devices are
accessed through the global devices list. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Split the function into omapdss_display_init() to perform
display-specific initialization of the omap_dss_device, and
omapdss_register_display() to register the device. The latter will then
be replaced by more generic registration.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Despite its name, the omap_dss_get_next_device() function operates on
display devices only. Make it more generic by allowing operation on all
devices, with a parameter to specify the device type.
While at it rename the function to omapdss_device_get_next() to match
the naming of the other functions operating on struct omap_dss_device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The macro iterates over displays only, rename it accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The output devices list isn't used anymore, all output devices are
accessed through the global devices list. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSI clocks are dumped in the DSS-level debugfs clocks file. This
complicates the implementation as the DSI private data has to be looked
up through the outputs list. Simplify it by creating two debugfs files,
dsi1_clks and dsi2_clks, to dump the DSI clocks.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSI debugfs regs and irqs show handlers received a pointer to the
DSI private data. There's no need to look it up from the list of DSS
outputs. Use the pointer directly, this allows simplifying the
implementation of the handlers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The encoders duplicate the same omap_dss_device src and dst fields set
and checks in their connect and disconnect handlers. Move the code to
the connect and disconnect wrappers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The connectors, encoders and display duplicate the same debug messages
and connection checks in their omap_dss_device connect and disconnect
handlers. Move the code to the connect and disconnect wrappers.
To simplify the code the connect function returns -EBUSY unconditionally
if the device is already connected. This doesn't cause any change in
practice: the connect handler of displays is never called on a connected
device as it is only invoked during omapdrm initialization.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_dss_device objects model display components and are connected
at runtime to create display pipelines. The connect and disconnect
operations implemented by each component contain lots of duplicate code.
As a first step towards fixing this, create new functions to wrap the
direct calls to those operations and use them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The various types of omapdss_*_ops structures define multiple operations
that are not specific to a bus type. To simplify the code and remove
dependencies on specific bus types move those operations to a common
structure. Operations that are specific to a bus type are kept in the
specialized ops structures.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_dss_find_output_by_port() function looks up an omap_dss_device
by port from the list of devices registered as outputs. In preparation
for looking up sinks in addition to sources, allow the function to look
up any registered device. Rename it to omap_dss_find_device_by_port() to
match its new purpose.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_dss_find_output_by_port_node() function defined in output.c
looks up an output from its port node. To do so it needs to call helper
functions from dss-of.c to lookup the port parent and the port number.
As omap_dss_find_output_by_port_node() is only called by
omapdss_of_find_source_for_first_ep() from dss-of.c this goes back and
forth between the to source files and isn't very clear.
Simplify the code by passing both the parent and the port number to
omap_dss_find_output_by_port_node() instead of the port node, and rename
the function to omap_dss_find_output_by_port().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdss_component_is_loaded() function test whether a component is
loaded by checking whether it is present in the displays list or the
outputs list. Simplify the implementation by checking for the component
in the global omap_dss_device list.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_dss_device instances are stored in two separate lists,
depending on whether they are panels or outputs. Create a third list
that stores all omap_dss_device instances to allow generic code to
operate on all instances.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
For coherency with the panel_list field, rename list to output_list.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_dss_device panel.dsi_pix_fmt and panel.dsi_mode fields are
unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_dss_device structure stores a videomode. All the connector and
panel drivers that use omap_dss_device also store the videomode in their
own panel_drv_data structures. There's no need to duplicate, remove the
videomode field from omap_dss_device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The structure contains function pointers that don't need to be modified.
Make all its instances const to improve security.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
All omap_dss_driver instances provide the get_timings operation. Remove
the default function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The get_timings operation from DSS encoders (not to be confused with the
identically named operation in omap_dss_driver) is never called. Remove
it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The operations are never used, remove them. If the need to set wide
screen signaling data arises later, it should be implemented by
extending the DRM bridge API.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The dpi_init_port() and sdi_init_port() functions can return errors but
their return value is ignored. This prevents both probe failures and
probe deferral from working correctly. Propagate the errors up the call
stack.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Register the omapdrm device when we know that dss device probe going
to succeed. This avoids DSS6 and DSS2 omapdrm device registration from
colliding with each other.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdss_gather_components() function walks the OF graph to create a
list of all components part of the display device. There's no need to
delay this operation until DSS bind time as we have all the information
we need at probe time.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As ordering of the dss_devices based on DT aliases is now implemented in
omap_drm.c, there is no need to do the ordering in dss/display.c
anymore.
At the same time remove the alias member of the omap_dss_device struct
since it is no longer needed. The only place it was used is in the
omapdss_register_display() function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Sort the dssdev array based on DT aliases.
With this change we can remove the panel ordering from dss/display.c and
have all sorting related to dssdevs in one place.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Description of DRA7 Errata i932:
In rare circumstances DPLL_VIDEO1 and DPLL_VIDEO2 PLL's may not lock on
the first attempt during DSS initialization. When this occurs, a
subsequent attempt to relock the PLL will result in PLL successfully
locking.
This patch does the following as per the errata recommendation:
- retries locking the PLL upto 20 times.
- The time to wait for a PLL lock set to 1000 REFCLK cycles. We use
usleep_range to wait for 1000 REFCLK cycles in the us range. This tight
constraint is imposed as a lock later than 1000 REFCLK cycles may have
high jitter.
- Criteria for PLL lock is extended from check on just the PLL_LOCK bit
to check on 6 PLL_STATUS bits.
Silicon Versions Impacted:
DRA71, DRA72, DRA74, DRA76 - All silicon revisions
AM57x - All silicon revisions
OMAP4/5 are not impacted by this errata
Signed-off-by: Venkateswara Rao Mandela <venkat.mandela@ti.com>
[tomi.valkeinen@ti.com: ported to v4.14]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
A bunch of debug and error prints are missing linefeeds. Add those.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180502091159.7071-4-tomi.valkeinen@ti.com
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
If get_scale_coef functions fail, they return NULL, but we never check
the return value and could do a NULL deref. This should not happen as we
ought to validate the amount of scaling already earlier, but to be safe,
add the necessary check.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180502091159.7071-3-tomi.valkeinen@ti.com
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
soc_device_match() can return NULL, so add a check and fail if
soc_device_match() fails.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180502091159.7071-2-tomi.valkeinen@ti.com
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
audio_config function for both HDMI4 and HDMI5 return uninitialized
value as the error code if the display is not currently enabled. For
some reason this has not caused any issues.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180329104038.29154-1-tomi.valkeinen@ti.com
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Commit 8a7eda7686 ("drm: omapdrm: dispc:
Pass DISPC pointer to remaining dispc API functions") made dpi.c use
ctx->pll even when there's no PLL, causing a crash at modeset on AM4
EVM, and presumably all OMAP2/3 boards.
Fix this by having struct dpi_data pointer in the ctx instead, giving
access to dispc without going through the pll.
Fixes: 8a7eda7686 ("drm: omapdrm: dispc: Pass DISPC pointer to remaining dispc API functions")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Keerthy <j-keerthy@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405065537.29818-1-tomi.valkeinen@ti.com
When CONFIG_OMAP2_DSS_DPI is disabled, compilation fails due to:
drivers/gpu/drm/omapdrm/dss/dss.h:388:25: error: conflicting types for ‘port’
struct device_node *port,
^~~~
Fix this by renaming the first parameter correctly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When compiling with CONFIG_OMAP2_DSS_DEBUGFS disabled, build fails due
to:
drivers/gpu/drm/omapdrm/dss/dss.c:1474:10: error: ‘dss_debug_dump_clocks’ undeclared (first use in this function); did you mean ‘dispc_dump_clocks’?
dss_debug_dump_clocks, dss);
^~~~~~~~~~~~~~~~~~~~~
dispc_dump_clocks
Fix this by moving the required functions outside #if
defined(CONFIG_OMAP2_DSS_DEBUGFS).
In the long term, we perhaps want to try to get all the debugfs support
left out if debugfs is not enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The setup code for color space conversion is a bit messy. This patch
cleans it up.
For some reason the TRM uses values in YCrCb order, which is also used
in the current driver, whereas everywhere else it's YCbCr (which also
matches YUV order). This patch changes the tables to use the common
order to avoid confusion.
The tables are split into separate lines, and comments added for
clarity.
WB color conversion registers are similar but different than non-WB, but
the same function was used to write both. It worked fine because the
coef table was adjusted accordingly, but that was rather confusing. This
patch adds a separate function to write the WB values so that the coef
table can be written in an understandable way.
Recalculation also showed that 'bcb' value in yuv-to-rgb conversion had
been rounded wrongly, and it should be 516 instead of 517.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Allow HDMI audio setup even if we do not have video configured. Audio
will get configured at the same time with video if the video is
configured soon enough. If it is not the audio DMA will timeout in
couple of seconds and audio playback will be aborted.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add writeback specific dispc functions to dispc_ops so that omapdrm can
use them. Also move 'enum dss_writeback_channel' to the public
omapdss.h for omapdrm.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
WB has additional scaling limits when the output color format is one of
the YUV formats. These limits are not handled at the moment, causing
bad scaling and/or NULL dereference crash.
This patchs adds the check so that dispc returns an error for bad
scaling request.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When using WB capture from interlaced source, we need to halve the
picture heights correctly.
Unfortunately the current dispc_ovl_setup_common() doesn't deal with
interlace very neatly, so the end result is a bit messy.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Benoit Parrot <bparrot@ti.com>
Vertical blanking needs to be halved on interlace modes. WBDELAYCOUNT
was calculated without such halving, resulting in WBUNCOMPLETE errors.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Benoit Parrot <bparrot@ti.com>
For HDMI, WBDELAYCOUNT starts counting at the start of vsync, not at the
start of vfp.
This patch adjusts the wbdelay for HDMI accordingly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We need to know the WB channel-in in wb_setup() to be able to configure
WB properly for capture mode. At the moment channel-in is set
separately.
This patch moves channel-in to wb_setup().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In dispc_set_ovl_common() we need to initialize pclk to a valid
value when we use WB in capture mode (i.e. mem_2_mem is false).
Otherwise dispc_ovl_calc_scaling() fails.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When dispc_wb_setup() calls dispc_ovl_setup_common() it does not
check for failure but instead keeps on partially setting up WB.
This causes the WB H/W to be partially initialized and yield
unexpected behavior.
Make sure return code is successful before proceeding.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
A few enums are not used anywhere, so remove them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Fix sparse warning:
drivers/gpu/drm/omapdrm/dss/dispc.c:387:9: warning: context imbalance in 'mgr_fld_write' - different lock contexts for basic block
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The venc private data structure is currently stored as a global
variable. While no platform with multiple VENC encoders currently exists
nor is planned, this doesn't comply with the kernel device model and
should thus be fixed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The sdi private data structure is currently stored as a global
variable. While no platform with multiple SDI encoders currently exists
nor is planned, this doesn't comply with the kernel device model and
should thus be fixed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The omap_hdmi private data structure is currently stored as a global
variable. While no platform with multiple HDMI5 encoders currently
exists nor is planned, this doesn't comply with the kernel device model
and should thus be fixed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The omap_hdmi private data structure is currently stored as a global
variable. While no platform with multiple HDMI4 encoders currently
exists nor is planned, this doesn't comply with the kernel device model
and should thus be fixed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The dispc private data structure is currently stored as a global
variable. While no platform with multiple DISPC currently exists
nor is planned, this doesn't comply with the kernel device model and
should thus be fixed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This removes the need to access the global DISPC private data in those
functions (both for the current accesses and the future ones that will
be introduced when allocating the DISPC private data dynamically).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This removes the need to access the global DISPC private data in those
functions (both for the current accesses and the future ones that will
be introduced when allocating the DISPC private data dynamically).
In order to allow the omapdrm side to call the dispc_ops with a DISPC
pointer, we also introduce a new function dss_get_dispc() to retrieve
the DISPC corresponding to the DSS.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Remove the global dispc ops variable by storing it in the dss_device
structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The dss_device is the top-level component in the omapdss driver. Give
the omapdrm driver access to the dss_device pointer in order to obtain
pointers to all other components from it. This requires a new global
variable in the omapdss driver that will be removed when merging the
omapdrm and omapdss drivers, but will already allow removal of several
other global variables.
As this partly duplicates the omapdss_is_initialized() API, reimplement
it as an inline function wrapping omapdss_get_dss().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The dss_mgr_ops operations implemented by the omapdrm side have to look
up the omap_crtc objects from global variables as they are only passed a
channel number. In order to remove global variables in the omapdrm
driver pass the omap_drm_private pointer to the dss_mgr_ops. This
requires storing a pointer to the omap_drm_private in a global variable
on the DSS side as a temporary measure until the omapdrm and omapdss
drivers get merged.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The dss_mgr_*() functions take a channel argument to identify the
channel they operate on. This prevents the functions from accessing
driver data structures without resorting to global variables. In an
effort to remove global variables, pass the omap_dss_device pointer
associated with the channel instead. This will be used to look up the
omap_drm_private data structure to pass to the dss_mgr_ops.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The dsi_display_init_dispc() and dsi_display_uninit_dispc() functions
take a channel argument that is reduntant as it is always identical to
the dsi->output.dispc_channel. Remove the argument and use the field
directly in the functions to avoid misuse.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The dsi_data structure stores a pointer to a struct platform_device. The
driver only uses the dev member of the platform device structure. Store
the struct device pointer instead and use it directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The dsi_bind() function receives a pointer to a struct device that it
casts to a struct platform_device, only to use the platform device's dev
field through the code. Use the dev pointer directly.
While at it rename the struct platform_device pointer dsidev to pdev to
make it more explicit.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The dsi_get_dsidrv_data() and dsi_get_dsidev_from_dssdev() inline
functions convert a struct omap_dss_device pointer to the corresponding
struct platform_device, and a struct platform_device pointer to the
corresponding struct dsi_data. They are nearly always called together
without any use of the intermediate platform_device, so combine them
into a single function.
In the three locations where only dsi_get_dsidrv_data() is used, call
dev_get_drvdata() directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Internal dsi functions take a pointer to the DSI platform_device and
then cast it to a dsi_data pointer. That's pointless as the caller
already has the dsi_data pointer. Pass it directly instead of the
platform_device pointer.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The dss_unbind() function casts the struct device pointer to a struct
platform_device, only to later use the struct device pointer from
platform_device. Don't cast at all.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
As part of an effort to remove the usage of global variables in the
driver, store the debugfs root directory in the dss_device structure
instead of a global variable.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
As part of an effort to remove the usage of global variables in the
driver, store the registered plls array in the dss_device structure
instead of a global variable.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
To simplify implementation of debugfs seq_file show handlers, the driver
passes the pointer to the show function through the debugfs_create_file
data pointer. This prevents using the pointer to pass driver private
data to the show handler, and requires all handlers to use global
variables to access private data.
To prepare for the removal of global private data in the driver, rework
the debugfs infrastructure to allow passing a private data pointer to
show handlers.
The price to pay is explicit removal of debugfs files to free the
internally allocated memory. This is desirable anyway as debugfs entries
should be removed when a component driver is unbound, otherwise crashes
will occur due to access to freed memory when the components will be
dynamically allocated instead of stored in global variables.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The DSS private data structure is currently stored as a global variable.
While no platform with multiple DSS devices currently exists nor is
planned, this doesn't comply with the kernel device model and should
thus be fixed.
Allocate the DSS private data structure dynamically for each DSS
instance and remove the global variable. All code that need access to
the structure now retrieves it dynamically so we can remove the global
variable.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This removes the need to access the global DSS private data in those
functions (both for the current accesses and the future ones that will
be introduced when allocating the DSS device dynamically).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This removes the need to access the global DSS private data in those
functions (both for the current accesses and the future ones that will
be introduced when allocating the DSS device dynamically).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This removes the need to access the global DSS private data in those
functions (both for the current accesses and the future ones that will
be introduced when allocating the DSS device dynamically).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This removes the need to access the global DSS private data in those
functions (both for the current accesses and the future ones that will
be introduced when allocating the DSS device dynamically).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This removes the need to access the global DSS private data in those
functions (both for the current accesses and the future ones that will
be introduced when allocating the DSS device dynamically).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This will allow accessing the PLL data to get the DSS device pointer,
removing the need to access the global DSS private data.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
To prepare for the removal of the global variable storing DSS private
data, pass its pointer to the dss_runtime_{get,put}() functions.
As this requires getting hold of the dss_device structure in the
callers, we add a new dss_get_device() function to retrieve it. The
function currently returns a pointer to the global data structure, and
will later be updated to get the pointer from device driver data when
the DSS private structure will be allocated dynamically.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The anoonymous dss structure in dss.c is the top-level component in the
omapdss driver. As such it should store all internal instance-specific
data that is currently stored in global variables. This however requires
both naming the structure to pass it around functions, and accessing it
from various locations in the omapdss driver. While we could implement
get and set functions for every field that needs to be accessed outside
of dss.c, that would introduce overhead and complexity that we could
avoid by exposing the structure to internal components of the omapdss
driver. Do so to prepare for removal of global variables.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The wait_for_bit_change() function returns the value of the bit it
polls. This requires the caller to compare the return value to the
expected bit value. As all the existing callers need is to check whether
the bit has reached the expected value, it's easier to return a boolean
status from the function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_dss_register_driver(), omap_dss_unregister_driver() and
dispc_enable_gamma_table() functions don't exist anymore, remove their
prototypes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The function is unused, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There's no reason to delay initialization of most of the driver (such as
mapping memory I/O, getting clocks or enabling runtime PM) to the
component master bind handler.
This additionally fixes a real PM issue caused enabling runtime PM in
the bind handler.
The bind handler performs the following sequence of PM operations:
pm_runtime_enable(dev);
pm_runtime_get_sync(dev);
... (access the hardware to read the device revision) ...
pm_runtime_put_sync(dev);
If a failure occurs at this point, the error path calls
pm_runtime_disable() to balance the pm_runtime_enable() call.
To understand the problem, it should be noted that the bind handler is
called when one of the component registers itself, which happens in the
component's probe handler. Furthermore, as the components are children
of the DSS, the device core calls pm_runtime_get_sync() on the DSS
platform device before calling the component's probe handler. This
increases the DSS power usage count but doesn't runtime resume the
device, as runtime PM is disabled at that point.
The bind handler is thus called with runtime PM disabled, with the
device runtime suspended, but with the power usage count larger than 0.
The pm_runtime_get_sync() call will thus further increase the power
usage count and runtime resume the device. The pm_runtime_put_sync()
handler will decrease the power usage count to a non-zero value and will
thus not suspend the device. Finally, the pm_runtime_disable() call will
disable runtime PM, preventing the pm_runtime_put() call in the device
core from runtime suspending the device. The DSS device is thus left
powered on.
To fix this, move the initialization code from the bind handler to the
probe handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
A few functions defined in omapdss-base are internal to the module.
Don't export them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The function isn't used outside of its compilation unit, make it static.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The kernel favours 'unsigned int' over plain 'unsigned'. Replace all
occurences of the latter by the former. This avoid lots of checkpatch
complaints in patches that touch lines where a plain 'unsigned' is used.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaW+iVAAoJEHm+PkMAQRiGCDsIAJALNpX7odTx/8y+yCSWbpBH
E57iwr4rmnI6tXJY6gqBUWTYnjAcf4b8IsHGCO6q3WIE3l/kt+m3eA21a32mF2Db
/bfPGTOWu5LoOnFqzgH2kiFuC3Y474toxpld2YtkQWYxi5W7SUtIHi/jGgkUprth
g15yPfwYgotJd/gpmPfBDMPlYDYvLlnPYbTG6ZWdMbg39m2RF2m0BdQ6aBFLHvbJ
IN0tjCM6hrLFBP0+6Zn60pevUW9/AFYotZn2ankNTk5QVCQm14rgQIP+Pfoa5WpE
I25r0DbkG2jKJCq+tlgIJjxHKD37GEDMc4T8/5Y8CNNeT9Q8si9EWvznjaAPazw=
=o5gx
-----END PGP SIGNATURE-----
BackMerge tag 'v4.15-rc8' into drm-next
Linux 4.15-rc8
Daniel requested this for so the intel CI won't fall over on drm-next
so often.
The omap4 CEC hardware cannot tell a Nack from a Low Drive from an
Arbitration Lost error, so just report a Nack, which is almost
certainly the reason for the error anyway.
This also simplifies the implementation. The only three interrupts
that need to be enabled are:
Transmit Buffer Full/Empty Change event: triggered when the
transmit finished successfully and cleared the buffer.
Receiver FIFO Not Empty event: triggered when a message was received.
Frame Retransmit Count Exceeded event: triggered when a transmit
failed repeatedly, usually due to the message being Nacked. Other
reasons are possible (Low Drive, Arbitration Lost) but there is no
way to know. If this happens the TX buffer needs to be cleared
manually.
While testing various error conditions I noticed that the hardware
can receive messages up to 18 bytes in total, which exceeds the legal
maximum of 16. This could cause a buffer overflow, so we check for
this and constrain the size to 16 bytes.
The old incorrect interrupt handler could cause the CEC framework to
enter into a bad state because it mis-detected the "Start Bit Irregularity
event" as an ARB_LOST transmit error when it actually is a receive error
which should be ignored.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Henrik Austad <haustad@cisco.com>
Tested-by: Henrik Austad <haustad@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, calls into each file are used to register the various
platform drivers. Change this to a table of pointers to platform_driver
structs to allow using platform_register_drivers.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Having the filename in the header serves little purpose and is
often wrong after renames as it is here in several places, just
drop it from all omapdrm files.
While we are here unify the copyright tags to the TI recommended style.
Signed-off-by: Andrew F. Davis <afd@ti.com>
The venc_probe_of() function has an error cleanup path that returns
success instead of an error code. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The dpi_data structure port_initialized field is used to check in the
cleanup path whether the DPI has been initialized. This can be performed
through the associated device_node data field instead. Remove the
port_initialized field.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The function isn't used outside of its compilation unit, make it static.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When merging the omapdrm and omapdss drivers the omapdrm virtual
platform device will disappear, and the omapdss platform device will be
used for DMA memory allocation. To prepare for that, set the DMA
coherent mask for the device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_dss_find_device() function is unused. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
While physical size information is automatically parsed for EDID
based displays, we need to provide it manually for displays providing
one fixed mode.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove driver (un)register API defines. They do not even exist
anymore.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The get_memory_bandwidth_limit() in dispc_ops can be used to query the
memory bandwidth limit of dispc by upper layers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
"ret" needs to be signed for the error handling to work.
Fixes: 8d7f934df8 ("omapdrm: hdmi4_cec: add OMAP4 HDMI CEC support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit d178e034d5 ("drm: omapdrm: Move FEAT_DPI_USES_VDDS_DSI feature
to dpi code") replaced usage of platform data version with SoC matching
to configure DPI VDDS. The SoC match entries were incorrect, they should
have matched on the machine name instead of the SoC family. Fix it.
The result was observed on OpenPandora with OMAP3530 where the panel only
had the Blue channel and Red&Green were missing. It was not observed on
GTA04 with DM3730.
Fixes: d178e034d5 ("drm: omapdrm: Move FEAT_DPI_USES_VDDS_DSI feature to dpi code")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: stable@vger.kernel.org # 4.14
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
I believe the intention of the commit 2c9fc9bf45
("drm: omapdrm: Move FEAT_HDMI_* features to hdmi4 driver")
was to identify omap4430 ES1.x, omap4430 ES2.x and other OMAP4 revisions,
like omap4460.
By using family=OMAP4 in the match the code will treat omap4460 ES1.x in a
same way as it would treat omap4430 ES1.x
This breaks HDMI audio on OMAP4460 devices (PandaES for example).
Correct the match rule so we are not going to get false positive match.
Fixes: 2c9fc9bf45 ("drm: omapdrm: Move FEAT_HDMI_* features to hdmi4 driver")
Cc: stable@vger.kernel.org # 4.14
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This mechanically converts all remaining cases of ancient open-coded timer
setup with the old setup_timer() API, which is the first step in timer
conversions. This has no behavioral changes, since it ultimately just
changes the order of assignment to fields of struct timer_list when
finding variations of:
init_timer(&t);
f.function = timer_callback;
t.data = timer_callback_arg;
to be converted into:
setup_timer(&t, timer_callback, timer_callback_arg);
The conversion is done with the following Coccinelle script, which
is an improved version of scripts/cocci/api/setup_timer.cocci, in the
following ways:
- assignments-before-init_timer() cases
- limit the .data case removal to the specific struct timer_list instance
- handling calls by dereference (timer->field vs timer.field)
spatch --very-quiet --all-includes --include-headers \
-I ./arch/x86/include -I ./arch/x86/include/generated \
-I ./include -I ./arch/x86/include/uapi \
-I ./arch/x86/include/generated/uapi -I ./include/uapi \
-I ./include/generated/uapi --include ./include/linux/kconfig.h \
--dir . \
--cocci-file ~/src/data/setup_timer.cocci
@fix_address_of@
expression e;
@@
init_timer(
-&(e)
+&e
, ...)
// Match the common cases first to avoid Coccinelle parsing loops with
// "... when" clauses.
@match_immediate_function_data_after_init_timer@
expression e, func, da;
@@
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
(
-\(e.function\|e->function\) = func;
-\(e.data\|e->data\) = da;
|
-\(e.data\|e->data\) = da;
-\(e.function\|e->function\) = func;
)
@match_immediate_function_data_before_init_timer@
expression e, func, da;
@@
(
-\(e.function\|e->function\) = func;
-\(e.data\|e->data\) = da;
|
-\(e.data\|e->data\) = da;
-\(e.function\|e->function\) = func;
)
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
@match_function_and_data_after_init_timer@
expression e, e2, e3, e4, e5, func, da;
@@
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
... when != func = e2
when != da = e3
(
-e.function = func;
... when != da = e4
-e.data = da;
|
-e->function = func;
... when != da = e4
-e->data = da;
|
-e.data = da;
... when != func = e5
-e.function = func;
|
-e->data = da;
... when != func = e5
-e->function = func;
)
@match_function_and_data_before_init_timer@
expression e, e2, e3, e4, e5, func, da;
@@
(
-e.function = func;
... when != da = e4
-e.data = da;
|
-e->function = func;
... when != da = e4
-e->data = da;
|
-e.data = da;
... when != func = e5
-e.function = func;
|
-e->data = da;
... when != func = e5
-e->function = func;
)
... when != func = e2
when != da = e3
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
@r1 exists@
expression t;
identifier f;
position p;
@@
f(...) { ... when any
init_timer@p(\(&t\|t\))
... when any
}
@r2 exists@
expression r1.t;
identifier g != r1.f;
expression e8;
@@
g(...) { ... when any
\(t.data\|t->data\) = e8
... when any
}
// It is dangerous to use setup_timer if data field is initialized
// in another function.
@script:python depends on r2@
p << r1.p;
@@
cocci.include_match(False)
@r3@
expression r1.t, func, e7;
position r1.p;
@@
(
-init_timer@p(&t);
+setup_timer(&t, func, 0UL);
... when != func = e7
-t.function = func;
|
-t.function = func;
... when != func = e7
-init_timer@p(&t);
+setup_timer(&t, func, 0UL);
|
-init_timer@p(t);
+setup_timer(t, func, 0UL);
... when != func = e7
-t->function = func;
|
-t->function = func;
... when != func = e7
-init_timer@p(t);
+setup_timer(t, func, 0UL);
)
Signed-off-by: Kees Cook <keescook@chromium.org>
-----BEGIN PGP SIGNATURE-----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=xVV2
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.15.
Core:
- Atomic object lifetime fixes
- Atomic iterator improvements
- Sparse/smatch fixes
- Legacy kms ioctls to be interruptible
- EDID override improvements
- fb/gem helper cleanups
- Simple outreachy patches
- Documentation improvements
- Fix dma-buf rcu races
- DRM mode object leasing for improving VR use cases.
- vgaarb improvements for non-x86 platforms.
New driver:
- tve200: Faraday Technology TVE200 block.
This "TV Encoder" encodes a ITU-T BT.656 stream and can be found in
the StorLink SL3516 (later Cortina Systems CS3516) as well as the
Grain Media GM8180.
New bridges:
- SiI9234 support
New panels:
- S6E63J0X03, OTM8009A, Seiko 43WVF1G, 7" rpi touch panel, Toshiba
LT089AC19000, Innolux AT043TN24
i915:
- Remove Coffeelake from alpha support
- Cannonlake workarounds
- Infoframe refactoring for DisplayPort
- VBT updates
- DisplayPort vswing/emph/buffer translation refactoring
- CCS fixes
- Restore GPU clock boost on missed vblanks
- Scatter list updates for userptr allocations
- Gen9+ transition watermarks
- Display IPC (Isochronous Priority Control)
- Private PAT management
- GVT: improved error handling and pci config sanitizing
- Execlist refactoring
- Transparent Huge Page support
- User defined priorities support
- HuC/GuC firmware refactoring
- DP MST fixes
- eDP power sequencing fixes
- Use RCU instead of stop_machine
- PSR state tracking support
- Eviction fixes
- BDW DP aux channel timeout fixes
- LSPCON fixes
- Cannonlake PLL fixes
amdgpu:
- Per VM BO support
- Powerplay cleanups
- CI powerplay support
- PASID mgr for kfd
- SR-IOV fixes
- initial GPU reset for vega10
- Prime mmap support
- TTM updates
- Clock query interface for Raven
- Fence to handle ioctl
- UVD encode ring support on Polaris
- Transparent huge page DMA support
- Compute LRU pipe tweaks
- BO flag to allow buffers to opt out of implicit sync
- CTX priority setting API
- VRAM lost infrastructure plumbing
qxl:
- fix flicker since atomic rework
amdkfd:
- Further improvements from internal AMD tree
- Usermode events
- Drop radeon support
nouveau:
- Pascal temperature sensor support
- Improved BAR2 handling
- MMU rework to support Pascal MMU
exynos:
- Improved HDMI/mixer support
- HDMI audio interface support
tegra:
- Prep work for tegra186
- Cleanup/fixes
msm:
- Preemption support for a5xx
- Display fixes for 8x96 (snapdragon 820)
- Async cursor plane fixes
- FW loading rework
- GPU debugging improvements
vc4:
- Prep for DSI panels
- fix T-format tiling scanout
- New madvise ioctl
Rockchip:
- LVDS support
omapdrm:
- omap4 HDMI CEC support
etnaviv:
- GPU performance counters groundwork
sun4i:
- refactor driver load + TCON backend
- HDMI improvements
- A31 support
- Misc fixes
udl:
- Probe/EDID read fixes.
tilcdc:
- Misc fixes.
pl111:
- Support more variants
adv7511:
- Improve EDID handling.
- HDMI CEC support
sii8620:
- Add remote control support"
* tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux: (1480 commits)
drm/rockchip: analogix_dp: Use mutex rather than spinlock
drm/mode_object: fix documentation for object lookups.
drm/i915: Reorder context-close to avoid calling i915_vma_close() under RCU
drm/i915: Move init_clock_gating() back to where it was
drm/i915: Prune the reservation shared fence array
drm/i915: Idle the GPU before shinking everything
drm/i915: Lock llist_del_first() vs llist_del_all()
drm/i915: Calculate ironlake intermediate watermarks correctly, v2.
drm/i915: Disable lazy PPGTT page table optimization for vGPU
drm/i915/execlists: Remove the priority "optimisation"
drm/i915: Filter out spurious execlists context-switch interrupts
drm/amdgpu: use irq-safe lock for kiq->ring_lock
drm/amdgpu: bypass lru touch for KIQ ring submission
drm/amdgpu: Potential uninitialized variable in amdgpu_vm_update_directories()
drm/amdgpu: potential uninitialized variable in amdgpu_vce_ring_parse_cs()
drm/amd/powerplay: initialize a variable before using it
drm/amd/powerplay: suppress KASAN out of bounds warning in vega10_populate_all_memory_levels
drm/amd/amdgpu: fix evicted VRAM bo adjudgement condition
drm/vblank: Tune drm_crtc_accurate_vblank_count() WARN down to a debug
drm/rockchip: add CONFIG_OF dependency for lvds
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CEC framework needs to know when the hotplug detect signal
disappears, since that means the CEC physical address has to be
invalidated (i.e. set to f.f.f.f).
Add a lost_hotplug op that is called when the HPD signal goes away.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Hook up the HDMI CEC support in the hdmi4 driver.
It add the CEC irq handler, the CEC (un)init calls and tells the CEC
implementation when the physical address changes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add the source and header for the OMAP4 HDMI CEC support.
This code is not yet hooked up, that will happen in the next patch.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The hdmi_power_on/off_core functions can be called multiple times:
when the HPD changes and when the HDMI CEC support needs to power
the HDMI core.
So use a counter to know when to really power on or off the HDMI core.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Call hdmi4_core_powerdown_disable() in hdmi_power_on_core() to
power up the HDMI core (needed for CEC). The same call can now be dropped
in hdmi4_configure().
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Pass struct omap_hdmi to the irq handler since it will need access
to hdmi.core.
Do not clear the IRQ_HDMI_CORE bit: that will be controlled by the
HDMI CEC code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Three low-level functions in hdmi4.c and hdmi4_core.c are
made available for use by the OMAP4 CEC support.
Renamed the prefix to hdmi4 since these are OMAP4 specific.
These function deal with the HDMI core and are needed to
power it up for use with CEC, even when the HPD is low.
Background: even if the HPD is low it should still be possible
to use CEC. Some displays will set the HPD low when they go into standby or
when they switch to another input, but CEC is still available and able
to wake up/change input for such a display.
This is explicitly allowed by the CEC standard.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Extend the hdmi_core_data struct with the additional fields needed
for CEC.
Also fix a simple typo in a comment.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
7d267f068a ("drm/omap: work-around for
errata i886") changed how the PLL dividers and multipliers are
calculated. While the new way should work fine for all the PLLs, it
breaks omap5 PLLs. The issues seen are rather odd: seemed that the
output clock rate is half of what we asked. It is unclear what's causing
there issues.
As a work-around this patch adds a "errata_i886" flag, which is set only
for DRA7's PLLs, and the PLL setup is done according to that flag.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
omapdrm rejects all venc (analog tv-out) videomodes, due to somewhat
strict checking of the values, making tv-out unusable.
We only support two videomodes, one for PAL and one for NTSC, so instead
of trying to check every field in the videomode struct, this patch makes
the driver check only the pixel clock and the size of the display.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that creating the omapdrm device from the platform code has been
removed, we can rename the omapdrm device back to "omapdrm".
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdss driver (not to be confused with the omapdss_dss driver) is
now a dummy driver with empty probe and remove functions. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdrm platform device is a virtual device created for the sole
purpose of handling the omapdss/omapdrm driver split. It should
eventually be removed. As a first step to ease refactoring move its
registration from platform code to driver code.
The omapdrm driver name must be changed internally to avoid probing both
the device registered in platform code and the device registered in the
omapdss driver, as that would otherwise break bisection.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There's no need to allocate memory dynamically to duplicate the contents
of a const structure, only to store the memory pointer in a const
pointer field. Just use the original structures directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The OMAP4 and OMAP5 HDMI PHYs have different properties that require
specific handling in the HDMI PHY driver. This needs knowledge of the
PHY version, which is currently inferred from the DSS version. As part
of the effort to remove usage of the DSS version, use the HDMI
controller version instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The OMAP4 and OMAP5 PLLs have different properties that require specific
handling in the HDMI PLL driver. This needs knowledge of the PLL
version, which is currently inferred from the DSS version. AS part of
the effort to remove usage of the DSS version, use the HDMI controller
version instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The HDMI audio driver only needs to know which generation of HDMI
transmitter it deals with, not the detailed SoC model. Pass the version
number as an integer to prepare for removal of the OMAP SoC version from
the omapdrm driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The HDMI wrapper code only needs to differentiate between major OMAP
revisions, which can be obtained from the HDMI transmitter compatible
string. Replace the OMAP SoC model checks to prepare for removal of the
OMAP SoC version platform data.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The dsi_pll_ops structure and dsi_init_pll_data() function incorrectly
use a dsi_ prefix, likely due to copy & paste. Fix it by using the
correct hdmi_ prefix.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are missing OMAP5 DSIPHY lane-enable support, which has prevented
OMAP5 DSI working in mainline. This patch adds the lane-enable similarly
to the recently added OMAP4 version.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Use regmap_update_bits instead of regmap_read/write, which simplifies
the code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The header file only contains four macros, two of which are never used.
Move the other two to dss.h and remove dss_features.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The supported outputs feature is specific to the DSS, move it from the
omap_dss_features structure to the dss driver.
The omap_dss_features structure is now empty and can be removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The FEAT_PARAM_DSS_FCK feature is specific to the DSS, move it from the
omap_dss_features structure to the dss driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The FEAT_PARAM_DSS_PCD, FEAT_PARAM_LINEWIDTH and FEAT_PARAM_DOWNSCALE
features are specific to the DISPC, move them from the omap_dss_features
structure to the dispc driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The FEAT_PARAM_DSI* features are specific to the DSI, move them from the
omap_dss_features structure to the dsi driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
All the remaining FEAT_* features are specific to the DISPC, move them
from the omap_dss_features structure to the dispc driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The FEAT_LCD_CLK_SRC feature is specific to the DSS, move it from the
omap_dss_features structure to the dss_features structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The FEAT_DPI_USES_VDDS_DSI feature is specific to the DPI, move it from
the omap_dss_features structure to the dpi code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The FEAT_HDMI_* features are specific to the HDMI4, move them from the
omap_dss_features structure to the hdmi4 driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The FEAT_DSI_* features are specific to the DSI, move them from the
omap_dss_features structure to the dsi driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The FEAT_VENC_REQUIRES_TV_DAC_CLK is specific to the VENC, move it from
the omap_dss_features structure to the venc driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The reg_fields feature describes DISPC registers only. Move it from the
omap_dss_features structure to the dispc_features structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The register belongs to the DSS, move the feature to the dss_features
structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The num_ovls and num_mgrs are dispc features. Move them from the
omap_dss_features structure to the dispc_features structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The overlay_caps is a dispc feature. Move it from the omap_dss_features
structure to the dispc_features structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The supported_color_modes is a dispc feature. Move it from the
omap_dss_features structure to the dispc_features structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The buffer_size_unit and burst_size_unit are dispc features. Move them
from the omap_dss_features structure to the dispc_features structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation for removal of the core module, move the shutdown()
handler from core to dss.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
debugfs code is spread between the core and dss drivers. In preparation
for removal of the core driver, move it all to the dss driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSS internal features are derived from the platform device
compatible string which is available at probe time. Don't delay
initialization until bind time. This prepares for the merge of the two
DSS features structures that will be needed before the DSS is bound.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The dss driver uses the supported display types to check whether the DSS
has SDI, VENC or HDMI outputs. We can instead use the supported outputs
the provide the same information. This removes the last use of the
supported display types, that we can then remove as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the compatible string instead of the OMAP SoC revision to determine
device features. The various OMAP3-based SoCs can't be told apart using
the compatible string, use soc_device_match() to tell them apart.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DPI code only needs to differentiate between major OMAP revisions,
which can be obtained from the DSS compatible string. Replace the OMAP
SoC model checks to prepare for removal of the OMAP SoC version platform
data.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the compatible string instead of the OMAP SoC revision to determine
device features. On OMAP34xx the features depend on the ES revision that
can not be determined from the compatible string. Use soc_device_match()
in that case.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The OMAP implementation of the set_min_bus_tput() API is a no-op.
There's no point in forwarding the driver calls to the platform code.
Remove the use of the related platform data callback, but keep the
internal function as a reminder that the feature will need to be
implemented when the OMAP platform will provide support.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Don't rely on callback functions provided by the platform, but access
the syscon internally to mux the DSI pins.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSI PLL hardware data and DSS channels are selected based on the
OMAP SoC model. There's no need for fine-grained model information, as
the driver only needs to differentiate between OMAP3, OMAP4 and OMAP5.
As this can be done through the DSI compatible string, store the
corresponding information in OF match data instead to avoid accessing
the OMAP SoC model.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move the two function pointers to a new dss_ops structure. This will
allow merging the dss_features and omap_dss_features structures without
having to expose the DPI source selection and LCD clock muxing functions
in header files.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
PHY features are stored in a global variable, while they should be
properties of the PHY object. As existing OMAP platforms have a single
HDMI PHY this doesn't cause any issue, but doesn't follow the driver
model.
Move the PHY features to the HDMI PHY data structure to follow the
driver model and pave the road for multiple HDMI PHYs support.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The two variables are never used outside of their compilation unit, make
them static.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The dpi_display_enable() function ensures that a VDDS_DSI regulator is
available if the DSI uses the VDDS_DSI supply. This is not needed, as a
failure to get the VDDS_DSI supply will result in a probe failure,
dpi_display_enable() will thus never be called in that case.
Remove the check, and replace tests for the FEAT_DPI_USES_VDDS_DSI
feature with a test for the regulator object.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The HPD signal can be used for detecting HDMI cable plug and unplug event
without the need for polling the status of the line.
This will speed up detecting such event because we do not need to wait for
the next poll event to notice the state change.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When rotating 90/270 + mirroring with YUV422, the end result will have
adjacent pixels swapped. The problem is that
dispc_ovl_set_rotation_attrs() has wrong rotation values for these
cases.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
TILER rotation with YUV422 pixelformats does not work at the moment. All
other pixel formats work, because the pixelformat's pixel size is equal
to tiler unit size (e.g. XR24's pixel size is 32 bits, and the TILER
unit size that has to be used is 32 bits).
For YUV422 formats this is not the case, as the TILER unit size has to
be 32 bits, but the pixel size is 16 bits. The end result is OCP errors
and sync losts.
This patch adds the code to adjust the variables for YUV422 formats.
We could make the code more generic by passing around the pixel format,
rotation type, angle and the tiler unit size, which would allow us to do
calculations without special case for YUV422. However, this would make
the code more complex, and at least for now this is much more easier to
handle with these two special cases for YUV422.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Change dispc driver to use the DRM_MODE_REFLECT flags instead of a mirror
boolean.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
At the moment the dispc driver uses a custom enum for rotation. Change
it to use the DRM's DRM_MODE_ROTATE_*.
Note that mirroring is at the moment handled as a separate boolean in
the dispc driver, so we only use the DRM_MODE_ROTATE_* values.
Note, DSS HW uses clockwise rotation, DRM counter-clockwise.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Now that we use fourccs, we can also rename the 'color_mode' variables
to 'fourcc'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
This patch changes omapdrm to use DRM_FORMAT_* values instead of
OMAP_DSS_COLOR_* enum.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
In this step we drop 'enum omap_color_mode', and use u32 instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
enum omap_color_mode is a bitmask, so at the moment we present the
supported color modes as mask. To be able to move to fourccs, we need to
use an array to present the supported color modes.
As a first step towards fourccs, this patch changes the code to use an
array to store the enums.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omapdss.h contains prototypes for three functions, which are also
defined in dss_features.h. Remove the extra prototypes from omapdss.h.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
In a few places the dispc driver needs to know whether the pixel format
is an YUV format. Add a helper to figure that out.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The code to calculate offset in dispc's calc_offset() is overly complex.
Simplify it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We have three rotation methods supported by the SoCs with DSS: DMA,
VRFB and TILER.
DMA rotation works in theory on all DSS platforms, but in practice it's
unusable due to the huge amount of memory bandwidth it uses, and has
never really been used.
VRFB is available on OMAP3, but is not supported by omapdrm, even though
we have some code for it in the dispc driver.
TILER is supported on OMAP4/OMAP5/DRA7/AM5 platforms, but has some
driver bugs.
To clean up the driver to help fixing the TILER issues, this patch drops
the DMA and VRFB rotation support, leaving only TILER rotation.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
