Since the commit 8b03ad30e3 ("drm/msm/dsi: Use one connector for dual
DSI mode"), the second DSI host in the bonded pair will not be
associated with the encoder and will not get the bridges, thus making
condition in msm_dsi_manager_set_split_display() always false.
Technically that change broke bonded DSI support in the MDP5 driver. But
since nobody complained in the last 5.5 years, it seems that nobody
cares enough.
Drop the msm_dsi_manager_set_split_display() completely and stop calling
the set_split_display() KMS callback. Also remove the
msm_dsi::external_bridge field which was only used by the mentioned
function.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/561695/
Link: https://lore.kernel.org/r/20231009205727.2781802-4-dmitry.baryshkov@linaro.org
Since the commit 8f59ee9a57 ("drm/msm/dsi: Adjust probe order") the
DSI hosts are not bound through the component framework if the DSI
driver wasn't attached to the DSI device connected to this host.
Afterwards, if there is no bridge (including the panel bridge) created
for the DSI device then devm_drm_of_get_bridge() will return an error,
also making msm_dsi_manager_ext_bridge_init() and thus DSI modesetting
init fail.
This way there can be no 'unconnected' MSM DSI bridges. Remove the
msm_dsi_device_connected() function.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/561692/
Link: https://lore.kernel.org/r/20231009205727.2781802-3-dmitry.baryshkov@linaro.org
This helper has been introduced to avoid programmer errors (missing
_put calls leading to dangling refcnt) when using pm_runtime_get, use it.
While at it, start checking the return value.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 5c82902844 ("drm/msm/dsi: Split PHY drivers to separate files")
Patchwork: https://patchwork.freedesktop.org/patch/543350/
Link: https://lore.kernel.org/r/20230620-topic-dsiphy_rpm-v2-1-a11a751f34f0@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes for v6.7-rc3:
- Fix the VREG_CTRL_1 for 4nm CPHY to match downstream
- Remove duplicate call to drm_kms_helper_poll_init() in msm_drm_init()
- Fix the safe_lut_tbl[] for sc8280xp to match downstream
- Don't attach the drm_dp_set_subconnector_property() for eDP
- Fix to attach drm_dp_set_subconnector_property() for DP. Otherwise
there is a bootup crash on multiple targets
- Remove unnecessary NULL check left behind during cleanup
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGtkna3P3mvaF53n2ARJACaXQU+OFfShayTrsUVmqCOmNQ@mail.gmail.com
Updates for v6.7
DP:
- use existing helpers for DPCD handling instead of open-coded functions
- set the subconnector type according to the plugged cable / dongle
skip validity check for DP CTS EDID checksum
DPU:
- continued migration of feature flags to use core revision checks
- reworked interrupts code to use '0' as NO_IRQ, removed raw IRQ indices
from log / trace output
gpu:
- a7xx support (a730, a740)
- fixes and additional speedbins for a635, a643
core:
- decouple msm_drv from kms to more cleanly support headless devices (like
imx5+a2xx)
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvzkBL2_OgyOeP_b6rVEjrNdfm8jcKzaB04HqHyT5jYwA@mail.gmail.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmU1ngkeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGrsIH/0k/+gdBBYFFdEym
foRhKir9WV3ZX4oIozJjA1f7T+qVYclKs6kaYm3gNepRBb6AoG8pdgv4MMAqhYsf
QMe2XHi0MrO/qKBgfNfivxEa9jq+0QK5uvTbqCRqCAB8LfwVyDqapCmg3EuiZcPW
UbMITmnwLIfXgPxvp9rabmCsTqO6FLbf0GDOVIkNSAIDBXMpcO1iffjrWUbhRa7n
oIoiJmWJLcXLxPWDsRKbpJwzw2cIG08YhfQYAiQnC3YaeRm1FKLDIICRBsmfYzja
rWv9r4dn4TDfV4/AnjggQnsZvz2yPCxNaFSQIT88nIeiLvyuUTJ9j8aidsSfMZQf
xZAbzbA=
=NoQv
-----END PGP SIGNATURE-----
BackMerge tag 'v6.6-rc7' into drm-next
This is needed to add the msm pr which is based on a higher base.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the drm/msm init code gets an error during output modeset
initialisation, the kernel will report an error regarding DRM memory
manager not being clean during shutdown. This is because
msm_dsi_modeset_init() allocates a piece of GEM memory for the TX
buffer, but destruction of the buffer happens only at
msm_dsi_host_destroy(), which is called during DSI driver's remove()
time, much later than the DRM MM shutdown.
To solve this issue, move the TX buffer destruction to dsi_unbind(), so
that the buffer is destructed at the correct time. Note, we also have to
store a reference to the address space, because priv->kms->aspace is
cleared before components are unbound.
Reported-by: Bjorn Andersson <andersson@kernel.org>
Fixes: 8f59ee9a57 ("drm/msm/dsi: Adjust probe order")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/562238/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Use exiting function to free the allocated GEM object instead of
open-coding it. This has a bonus of internally calling
msm_gem_put_vaddr() to compensate for msm_gem_get_vaddr() in
msm_get_kernel_new().
Fixes: 1e29dff004 ("drm/msm: Add a common function to free kernel buffer objects")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/562239/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Make MSM DSI driver use devm_drm_bridge_add() instead of plain
drm_bridge_add(). As the driver doesn't require any additional cleanup,
stop adding created bridge to the priv->bridges array.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/561636/
Signed-off-by: Rob Clark <robdclark@chromium.org>
drm-misc-next for v6.7-rc1:
UAPI Changes:
- Nouveau changed to not set NO_PREFETCH flag explicitly.
Cross-subsystem Changes:
- Update documentation of dma-buf intro and uapi.
- fbdev/sbus fixes.
- Use initializer macros in a lot of fbdev drivers.
- Add Boris Brezillon as Panfrost driver maintainer.
- Add Jessica Zhang as drm/panel reviewer.
- Make more fbdev drivers use fb_ops helpers for deferred io.
- Small hid trailing whitespace fix.
- Use fb_ops in hid/picolcd
Core Changes:
- Assorted small fixes to ttm tests, drm/mst.
- Documentation updates to bridge.
- Add kunit tests for some drm_fb functions.
- Rework drm_debugfs implementation.
- Update xe documentation to mark todos as completed.
Driver Changes:
- Add support to rockchip for rv1126 mipi-dsi and vop.
- Assorted small fixes to nouveau, bridge/samsung-dsim,
bridge/lvds-codec, loongson, rockchip, panfrost, gma500, repaper,
komeda, virtio, ssd130x.
- Add support for simple panels Mitsubishi AA084XE01,
JDI LPM102A188A,
- Documentation updates to accel/ivpu.
- Some nouveau scheduling/fence fixes.
- Power management related fixes and other fixes to ivpu.
- Assorted bridge/it66121 fixes.
- Make platform drivers return void in remove() callback.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3da6554b-3b47-fe7d-c4ea-21f4f819dbb6@linux.intel.com
The irq_of_parse_and_map() function returns zero on error. It
never returns negative error codes. Fix the check.
Fixes: a689554ba6 ("drm/msm: Initial add DSI connector support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/557715/
Link: https://lore.kernel.org/r/4f3c5c98-04f7-43f7-900f-5d7482c83eef@moroto.mountain
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
dsi_wait4video_done() API waits for the DSI video mode engine to
become idle so that we can transmit the DCS commands in the
beginning of BLLP. However, with the current sequence, the MDP
timing engine is turned on after the panel's pre_enable() callback
which can send out the DCS commands needed to power up the panel.
During those cases, this API will always timeout and print out the
error spam leading to long bootup times and log flooding.
Fix this by checking if the DSI video engine was actually busy before
waiting for it to become idle otherwise this is a redundant wait.
changes in v2:
- move the reg read below the video mode check
- minor fixes in commit text
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/34
Fixes: a689554ba6 ("drm/msm: Initial add DSI connector support")
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/557853/
Link: https://lore.kernel.org/r/20230915204426.19011-1-quic_abhinavk@quicinc.com
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert the msm drm drivers from always returning zero in the
remove callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230507162616.1368908-32-u.kleine-koenig@pengutronix.de
Updates for v6.6, which includes a backmerge of msm-fixes to avoid conficts.
Core:
- SM6125 MDSS support
DPU:
- SM6125 DPU support
- Added subblocks to display snapshot
- Use UBWC data from MDSS driver rather than duplicating it
- dpu_core_perf cleanup
DSI:
- Enabled burst mode to fix CMD mode panels
- Runtime PM support
- refgen regulator support
DSI PHY:
- SM6125 support in 14nm DSI PHY driver
GPU:
- Rework GPU identification to prepare for a7xx, and other a7xx prep
- Cleanups and fixes
- Disallow legacy relocs on a6xx and newer
- a690: switch to using a660_gmu.bin fw as this is what we have in
linux-firmware and we see no evidence that it should be different
from other a660 family (a6xx subgen 4) devices
- Submit overhead opts, 1.6x faster for NO_IMPLICIT_SYNC commits with
100 BOs to 2.5x faster for 1000 BOs
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGv_01g-edjdfKLWWcb-rO5aSyLsv5FpbKrTkXVL9+ngTQ@mail.gmail.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmTiDvweHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG7doH/2Poj73npPKPVfT3
RF8AsgvAj2pLby67rdvwTdFX+exS63SsuwtGGRfAHfGabiwmNN+oT2dLb0aY15bp
nskHnFpcqQ/pfZ2i2rUCenzBX8S9QULvPidLKRaf1FcSdOzqd97Bw5oDPMtzqy/R
Pm+Dzs//7fYvtm69nt6hKW4d6wXxNcg7Fk/QgoJ5Ax9vGvDuZmWXH0ZgBf/5kH04
TTPQNtVX57lf+FHugkhFEn4JbYXvN168b+LuX2PHwOeG/8AIS69Hc0vgvhHNAycT
mmpUI1gWA2jfrJ2RCyyezF/6wy9Ocsp+CbPjfwjuRUxOk0XIm1+cp9Mlz/cRbMsZ
f0tOTpk=
=xrJp
-----END PGP SIGNATURE-----
BackMerge tag 'v6.5-rc7' into drm-next
Linux 6.5-rc7
This is needed for the CI stuff and the msm pull has fixes in it.
Signed-off-by: Dave Airlie <airlied@redhat.com>
SM6125 features only a single PHY (despite a secondary PHY PLL source
being available to the disp_cc_mdss_pclk0_clk_src clock), and downstream
sources for this "trinket" SoC do not define the typical "vcca"
regulator to be available nor used. This, including the register offset
is identical to QCM2290, whose config struct can trivially be reused.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/548980/
Link: https://lore.kernel.org/r/20230723-sm6125-dpu-v4-13-a3f287dd6c07@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The regulator setup was likely copied from other SoCs by mistake. Just
like SM6125 the DSI PHY on this platform is not getting power from a
regulator but from the MX power domain.
Fixes: 572e9fd6d1 ("drm/msm/dsi: Add phy configuration for QCM2290")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/548959/
Link: https://lore.kernel.org/r/20230723-sm6125-dpu-v4-1-a3f287dd6c07@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
During a frame transfer in command mode, there could be frequent
LP11 <-> HS transitions when multiple DCS commands are sent mid-frame or
if the DSI controller is running on slow clock and is throttled. To
minimize frame latency due to these transitions, it is recommended to
send the frame in a single burst.
This feature is supported for DSI 6G 1.3 and above, thus enable burst
mode if supported.
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/544551/
Link: https://lore.kernel.org/r/20230608-b4-add-burst-mode-v2-1-2ff468457d46@quicinc.com
[DB: fixed indentation]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714174545.4056287-1-robh@kernel.org
The regulator setup was likely copied from other SoCs by mistake. Just
like SM6125 the DSI PHY on this platform is not getting power from a
regulator but from the MX power domain.
Fixes: 572e9fd6d1 ("drm/msm/dsi: Add phy configuration for QCM2290")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/544536/
Link: https://lore.kernel.org/r/20230627-sm6125-dpu-v2-1-03e430a2078c@somainline.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Currently, slice_count is being used to calculate word count and
pkt_per_line. Instead, these values should be calculated using slice per
packet, which is not the same as slice_count.
Slice count represents the number of slices per interface, and its value
will not always match that of slice per packet. For example, it is possible
to have cases where there are multiple slices per interface but the panel
specifies only one slice per packet.
Thus, use the default value of one slice per packet and remove slice_count
from the aforementioned calculations.
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Fixes: bc6b6ff813 ("drm/msm/dsi: Use DSC slice(s) packet size to compute word count")
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/541965/
Link: https://lore.kernel.org/r/20230405-add-dsc-support-v6-5-95eab864d1b6@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Currently, when compression is enabled, hdisplay is reduced via integer
division. This causes issues for modes where the original hdisplay is
not a multiple of 3.
To fix this, use DIV_ROUND_UP to divide hdisplay.
Suggested-by: Marijn Suijten <marijn.suijten@somainline.org>
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/541970/
Link: https://lore.kernel.org/r/20230405-add-dsc-support-v6-1-95eab864d1b6@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Currently, hdisplay is being divided by 3 for DSC. However, this
calculation only works for cases where BPP = 8.
Update hdisplay calculation to be bytes_per_line / 3, so that it
accounts for cases where BPP != 8.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/539271/
Link: https://lore.kernel.org/r/20230329-rfc-msm-dsc-helper-v14-9-bafc7be95691@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Use new DRM DSC helpers to setup DSI DSC configuration. The
initial_scale_value needs to be adjusted according to the standard, but
this is a separate change.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/539276/
Link: https://lore.kernel.org/r/20230329-rfc-msm-dsc-helper-v14-4-bafc7be95691@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
MSM8226 uses a modified PLL lock sequence compared to MSM8974, which is
based on the function dsi_pll_enable_seq_m in the msm-3.10 kernel.
Worth noting that the msm-3.10 downstream kernel also will try other
sequences in case this one doesn't work, but during testing it has shown
that the _m sequence succeeds first time also:
.pll_enable_seqs[0] = dsi_pll_enable_seq_m,
.pll_enable_seqs[1] = dsi_pll_enable_seq_m,
.pll_enable_seqs[2] = dsi_pll_enable_seq_d,
.pll_enable_seqs[3] = dsi_pll_enable_seq_d,
.pll_enable_seqs[4] = dsi_pll_enable_seq_f1,
.pll_enable_seqs[5] = dsi_pll_enable_seq_c,
.pll_enable_seqs[6] = dsi_pll_enable_seq_e,
We may need to expand this in the future.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/540618/
Link: https://lore.kernel.org/r/20230308-msm8226-mdp-v3-6-b6284145d67a@z3ntu.xyz
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Add the config for the v1.0.2 DSI found on MSM8226. We can reuse
existing bits from other revisions that are identical for v1.0.2.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Patchwork: https://patchwork.freedesktop.org/patch/540616/
Link: https://lore.kernel.org/r/20230308-msm8226-mdp-v3-5-b6284145d67a@z3ntu.xyz
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
In dsi_calc_clk_rate_v2() there is no need to call dsi_get_pclk_rate().
This function has just been called (from dsi_calc_pclk()) and its
result is stored at msm_host->pixel_clk_rate. Use this variable
directly.
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/538272/
Link: https://lore.kernel.org/r/20230520200103.4019607-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
If the dispcc uses CLK_OPS_PARENT_ENABLE (e.g. on QCM2290), CCF can try
enabling VCO before the rate has been programmed. This can cause clock
lockups and/or other boot issues. Program the VCO to the minimal PLL
rate if the read rate is 0 Hz.
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reported-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reported-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Fixes: f079f6d999 ("drm/msm/dsi: Add PHY/PLL for 8x96")
Patchwork: https://patchwork.freedesktop.org/patch/534813/
Link: https://lore.kernel.org/r/20230501011257.3460103-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
In commit 7d8e9a9050 ("drm/msm/dsi: move DSI host powerup to modeset
time") the error handling with regards to dsi_mgr_bridge_power_on()
got a bit worse. Specifically if we failed to power the bridge on then
nothing would really notice. The modeset function couldn't return an
error and thus we'd blindly go forward and try to do the pre-enable.
In commit ec7981e6c6 ("drm/msm/dsi: don't powerup at modeset time
for parade-ps8640") we added a special case to move the powerup back
to pre-enable time for ps8640. When we did that, we didn't try to
recover the old/better error handling just for ps8640.
In the patch ("drm/msm/dsi: Stop unconditionally powering up DSI hosts
at modeset") we've now moved the powering up back to exclusively being
during pre-enable. That means we can add the better error handling
back in, so let's do it. To do so we'll add a new function
dsi_mgr_bridge_power_off() that's matches how errors were handled
prior to commit 7d8e9a9050 ("drm/msm/dsi: move DSI host powerup to
modeset time").
NOTE: Now that we have dsi_mgr_bridge_power_off(), it feels as if we
should be calling it in dsi_mgr_bridge_post_disable(). That would make
some sense, but doing so would change the current behavior and thus
should be a separate patch. Specifically:
* dsi_mgr_bridge_post_disable() always calls dsi_mgr_phy_disable()
even in the slave-DSI case of bonded DSI. We'd need to add special
handling for this if it's truly needed.
* dsi_mgr_bridge_post_disable() calls msm_dsi_phy_pll_save_state()
midway through the poweroff.
* dsi_mgr_bridge_post_disable() has a different order of some of the
poweroffs / IRQ disables.
For now we'll leave dsi_mgr_bridge_post_disable() alone.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/521059/
Link: https://lore.kernel.org/r/20230131141756.RFT.v2.3.I3c87b53c4ab61a7d5e05f601a4eb44c7e3809a01@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
In commit 7d8e9a9050 ("drm/msm/dsi: move DSI host powerup to modeset
time"), we moved powering up DSI hosts to modeset time. This wasn't
because it was an elegant design, but there were no better options.
That commit actually ended up breaking ps8640, and thus was born
commit ec7981e6c6 ("drm/msm/dsi: don't powerup at modeset time for
parade-ps8640") as a temporary hack to un-break ps8640 by moving it to
the old way of doing things. It turns out that ps8640 _really_ doesn't
like its pre_enable() function to be called after
dsi_mgr_bridge_power_on(). Specifically (from experimentation, not
because I have any inside knowledge), it looks like the assertion of
"RST#" in the ps8640 runtime resume handler seems like it's not
allowed to happen after dsi_mgr_bridge_power_on()
Recently, Dave Stevenson's series landed allowing bridges some control
over pre_enable ordering. The meaty commit for our purposes is
commit 4fb912e5e1 ("drm/bridge: Introduce pre_enable_prev_first to
alter bridge init order"). As documented by that series, if a bridge
doesn't set "pre_enable_prev_first" then we should use the old ordering.
Now that we have the commit ("drm/bridge: tc358762: Set
pre_enable_prev_first") we can go back to the old ordering, which also
allows us to remove the ps8640 special case.
One last note is that even without reverting commit 7d8e9a9050
("drm/msm/dsi: move DSI host powerup to modeset time"), if you _just_
revert the ps8640 special case and try it out then it doesn't seem to
fail anymore. I spent time bisecting / debugging this and it turns out
to be mostly luck, so we still want this patch to make sure it's
solid. Specifically the reason it sorta works these days is because
we implemented wait_hpd_asserted() in ps8640 now, plus the magic of
"pm_runtime" autosuspend. The fact that we have wait_hpd_asserted()
implemented means that we actually power the bridge chip up just a wee
bit earlier and then the bridge happens to stay on because of
autosuspend and thus ends up powered before dsi_mgr_bridge_power_on().
Cc: Dave Stevenson <dave.stevenson@raspberrypi.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/521058/
Link: https://lore.kernel.org/r/20230131141756.RFT.v2.2.I4cfeab9d0e07e98ead23dd0736ab4461e6c69002@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Now that the only user is handled by common code, remove the option to
specify custom handlers through match data.
This is effectively a revert of commit:
5ae15e76271 ("drm/msm/dsi: Allow to specify dsi config as pdata")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/527662/
Link: https://lore.kernel.org/r/20230307-topic-dsi_qcm-v6-7-70e13b1214fa@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Now that the logic can handle multiple sets of registers, move
the QCM2290 to the common logic and mark it deprecated. This allows us
to remove a couple of structs, saving some memory.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/527656/
Link: https://lore.kernel.org/r/20230307-topic-dsi_qcm-v6-6-70e13b1214fa@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The configs are identical, other than the number of *maximum* DSI
hosts allowed. This isn't an issue, unless somebody deliberately
tries to access the inexistent host by adding a dt node for it.
Remove the SC7180 struct and point the hw revision match to the
SDM845's one. On a note, this could have been done back when
7180 support was introduced.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/527654/
Link: https://lore.kernel.org/r/20230307-topic-dsi_qcm-v6-5-70e13b1214fa@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Currently, we allow for MAX_DSI entries in io_start to facilitate for
MAX_DSI number of DSI hosts at different addresses. The configuration
is matched against the DSI CTRL hardware revision read back from the
component. We need a way to resolve situations where multiple SoCs
with different register maps may use the same version of DSI CTRL. In
preparation to do so, make msm_dsi_config a 2d array where each entry
represents a set of configurations adequate for a given SoC.
This is totally fine to do, as the only differentiating factors
between same-version-different-SoCs configurations are the number of
DSI hosts (1 or 2, at least as of today) and the set of base registers.
The regulator setup is the same, because the DSI hardware is the same,
regardless of the SoC it was implemented in.
In addition to that, update the matching logic such that it will loop
over VARIANTS_MAX variants, making sure they are all taken into account.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/527652/
Link: https://lore.kernel.org/r/20230307-topic-dsi_qcm-v6-3-70e13b1214fa@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
In preparation for supporting multiple sets of possible base registers,
remove the num_dsi variable. We're comparing the io_start array contents
with the reg value from the DTS, so it will either match one of the
expected values or don't match against a zero (which we get from partial
array initialization).
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/527658/
Link: https://lore.kernel.org/r/20230307-topic-dsi_qcm-v6-2-70e13b1214fa@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
It was left unnoticed during the review that even if there is no OPP
table in device tree, one will be created by a call to the function
devm_pm_opp_set_clkname(). This leads to dsi_mgr_bridge_mode_valid()
rejecting all modes if DT contains no OPP table for the DSI host.
Rework dsi_mgr_bridge_mode_valid() to handle this case by actually
checking that the table is populated with frequency entries before
returning an error.
Fixes: 8328041b8c ("drm/msm/dsi: implement opp table based check for dsi_mgr_bridge_mode_valid()")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/520076/
Link: https://lore.kernel.org/r/20230124203600.3488766-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
DPU, DSI, MDSS:
- Support for SM8350, SM8450 SM8550 and SC8280XP platform
Core:
- Added bindings for SM8150 (driver support already present)
DPU:
- Partial support for DSC on SM8150 and SM8250
- Fixed color transformation matrix being lost on suspend/resume
DP:
- Support for DP on SDM845 and SC8280XP platforms
- HPD fixes
- Support for limiting DP link rate via DT property, this enables
support for HBR3 rates.
DSI:
- Validate display modes according to the DSI OPP table
- DSI PHY support for the SM6375 platform
- Fixed byte intf clock selection for 14nm PHYs
MDP5:
- Schema conversion to YAML
Misc fixes as usual
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
v2.5.0 support was originally added for SC7280, but this hw is also
present on SM8350, which has one more DSI host. Bump up the dsi count
and fill in the register of the secondary host to allow it to probe.
This should not have any adverse effects on SC7280, as the secondary
CTRL will only be touched if it's defined, anyway.
Fixes: 65c391b319 ("drm/msm/dsi: Add DSI support for SC7280")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/519513/
Link: https://lore.kernel.org/r/20230120210101.2146852-1-konrad.dybcio@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
According to the vendor kernel, byte intf clock rate should be a half of
the byte clock only when DSI PHY version is above 2.0 (in other words,
10nm PHYs and later) and only if PHY is used in D-PHY mode. Currently
MSM DSI code handles only the second part of the clause (C-PHY vs
D-PHY), skipping DSI PHY version check, which causes issues on some of
14nm DSI PHY platforms (e.g. qcm2290).
Move divisor selection to DSI PHY code, pass selected divisor through
shared timings and set byte intf clock rate accordingly.
Cc: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org> # SM6115P J606F
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/519006/
Link: https://lore.kernel.org/r/20230118130027.2345719-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Currently there is no protection against a user trying to set
an unsupported mode on DSI. Implement a check based on the opp
table whether the byte clock for the mode can be supported by
validating whether an opp table entry exists.
For devices which have not added opp table support yet, skip
this check otherwise it will break bootup on those devices.
changes in v3:
- make the comment shorter
- handle all errors except ENODEV
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/15
Reported-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/518008/
Link: https://lore.kernel.org/r/20230112001600.12791-2-quic_abhinavk@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Re-arrange the dsi_calc_pclk method to two helpers, one to
compute the DSI byte clk and the other to compute the pclk.
This makes the separation of the two clean and also allows
clients to compute and use the dsi byte clk separately.
changes in v2:
- move the assignments to definition lines
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/518005/
Link: https://lore.kernel.org/r/20230112001600.12791-1-quic_abhinavk@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
According to downstream /and the comment copied from it/ this comparison
should be the other way around. In other words, when the panel driver
requests to use more slices per packet than what could be sent over this
interface, it is bumped down to only use a single slice per packet (and
strangely not the number of slices that could fit on the interface).
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/515686/
Link: https://lore.kernel.org/r/20221221231943.1961117-4-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
According to downstream the value to use for WORD_COUNT is
bytes_per_pkt, which denotes the number of bytes in a packet based on
how many slices have been configured by the panel driver times the
width of a slice times the number of bytes per pixel.
The DSC panels seen thus far use one byte per pixel, only one slice
per packet, and a slice width of half the panel width leading to the
desired bytes_per_pkt+1 value to be equal to hdisplay/2+1. This however
isn't the case anymore for panels that configure two slices per packet,
where the value should now be hdisplay+1.
Note that the aforementioned panel (on a Sony Xperia XZ3, sdm845) with
slice_count=1 has also been tested to successfully accept slice_count=2,
which would have shown corrupted output previously.
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/515694/
Link: https://lore.kernel.org/r/20221221231943.1961117-3-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
In preparation to adding the sm8350 and sm8450 PHYs support, rearrange
register values calculations in dsi_7nm_phy_enable(). This change bears
no functional changes itself, it is merely a preparation for the next
patch.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/514232/
Link: https://lore.kernel.org/r/20221207012231.112059-6-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The bpg_offset array contains negative BPG offsets which fill the full 8
bits of a char thanks to two's complement: this however results in those
bits bleeding into the next field when the value is packed into DSC PPS
by the drm_dsc_helper function, which only expects range_bpg_offset to
contain 6-bit wide values. As a consequence random slices appear
corrupted on-screen (tested on a Sony Tama Akatsuki device with sdm845).
Use AND operators to limit these two's complement values to 6 bits,
similar to the AMD and i915 drivers.
Fixes: b9080324d6 ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508941/
Link: https://lore.kernel.org/r/20221026182824.876933-11-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
drm_dsc_config's bits_per_pixel field holds a fractional value with 4
bits, which all panel drivers should adhere to for
drm_dsc_pps_payload_pack() to generate a valid payload. All code in the
DSI driver here seems to assume that this field doesn't contain any
fractional bits, hence resulting in the wrong values being computed.
Since none of the calculations leave any room for fractional bits or
seem to indicate any possible area of support, disallow such values
altogether. calculate_rc_params() in intel_vdsc.c performs an identical
bitshift to get at this integer value.
Fixes: b9080324d6 ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508938/
Link: https://lore.kernel.org/r/20221026182824.876933-8-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
As per the FIXME this code is entirely duplicate with what is already
provided inside drm_dsc_compute_rc_parameters(), supposedly because that
function was yielding "incorrect" results while in reality the panel
driver(s?) used for testing were providing incorrect parameters.
For example, this code from downstream assumed dsc->bits_per_pixel to
contain an integer value, whereas the upstream drm_dsc_config struct
stores it with 4 fractional bits. drm_dsc_compute_rc_parameters()
already accounts for this feat while the panel driver used for testing
[1] wasn't, hence making drm_dsc_compute_rc_parameters() seem like it
was returning an incorrect result.
Other users of dsc->bits_per_pixel inside dsi_populate_dsc_params() also
treat it in the same erroneous way, and will be addressed in a separate
patch.
In the end, using drm_dsc_compute_rc_parameters() spares both a lot of
duplicate code and erratic behaviour.
[1]: https://git.linaro.org/people/vinod.koul/kernel.git/commit/?h=topic/pixel3_5.18-rc1&id=1d7d98ad564f1ec69e7525e07418918d90f247a1
Fixes: b9080324d6 ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/508939/
Link: https://lore.kernel.org/r/20221026182824.876933-7-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
This field is currently unread but will come into effect when duplicated
code below is migrated to call drm_dsc_compute_rc_parameters(), which
uses the bpc-dependent value of the local variable mux_words_size in
much the same way.
The hardcoded constant seems to be a remnant from the `/* bpc 8 */`
comment right above, indicating that this group of field assignments is
applicable to bpc = 8 exclusively and should probably bail out on
different bpc values, until constants for other bpc values are added (or
the current ones are confirmed to be correct across multiple bpc's).
Fixes: b9080324d6 ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508943/
Link: https://lore.kernel.org/r/20221026182824.876933-6-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
dsi_populate_dsc_params() is called prior to dsi_update_dsc_timing() and
already computes a value for slice_chunk_size, whose value doesn't need
to be recomputed and re-set here.
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508934/
Link: https://lore.kernel.org/r/20221026182824.876933-5-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
This exact same math is used to compute bytes_in_slice above in
dsi_update_dsc_timing(), also used to fill slice_chunk_size.
Fixes: b9080324d6 ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508935/
Link: https://lore.kernel.org/r/20221026182824.876933-4-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Multiplying a value by 2 and adding 1 to it always results in a value
that is uneven, and that 1 gets truncated immediately when performing
integer division by 2 again. There is no "rounding" possible here.
After that target_bpp_x16 is used to store a multiplication of
bits_per_pixel by 16 which is only ever read to immediately be divided
by 16 again, and is elided in much the same way.
Fixes: b9080324d6 ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508932/
Link: https://lore.kernel.org/r/20221026182824.876933-2-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The QCM2290 SoC a the 14nm (V2.0) single DSI phy. The platform is not
fully compatible with the standard 14nm PHY, so it requires a separate
compatible and config entry.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
[DB: rebased and updated commit msg]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/504578/
Link: https://lore.kernel.org/r/20220924121900.222711-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Drop the overly defensive modeset sanity checks of function parameters
which have already been checked or used by the callers.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/502678/
Link: https://lore.kernel.org/r/20220913085320.8577-11-johan+linaro@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Add the missing sanity check on the bridge counter to avoid corrupting
data beyond the fixed-sized bridge array in case there are ever more
than eight bridges.
Fixes: a689554ba6 ("drm/msm: Initial add DSI connector support")
Cc: stable@vger.kernel.org # 4.1
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/502668/
Link: https://lore.kernel.org/r/20220913085320.8577-4-johan+linaro@kernel.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Clang warns:
drivers/gpu/drm/msm/dsi/dsi_host.c:1903:14: error: variable 'device_node' is uninitialized when used here [-Werror,-Wuninitialized]
of_node_put(device_node);
^~~~~~~~~~~
drivers/gpu/drm/msm/dsi/dsi_host.c:1870:44: note: initialize the variable 'device_node' to silence this warning
struct device_node *endpoint, *device_node;
^
= NULL
1 error generated.
device_node's assignment was removed but not all of its uses. Remove the
call to of_node_put() and the variable declaration to clean up the
warning.
Fixes: 36246dd50225 ("drm/msm/dsi: switch to DRM_PANEL_BRIDGE")
Link: https://github.com/ClangBuiltLinux/linux/issues/1700
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/500182/
Link: https://lore.kernel.org/r/20220829165450.217628-1-nathan@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Currently the DSI driver has two separate paths: one if the next device
in a chain is a bridge and another one if the panel is connected
directly to the DSI host. Simplify the code path by using panel-bridge
driver (already selected in Kconfig) and dropping support for
handling the panel directly.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/493608/
Link: https://lore.kernel.org/r/20220712132258.671263-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Now that struct mipi_dsi_device provides DSC data, fetch it from the
mentioned struct rather than from the struct drm_panel itself. This
would allow supporting MIPI DSI bridges handling DSC on their input
side.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/493307/
Link: https://lore.kernel.org/r/20220711094320.368062-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Return the value msm_dsi_phy_enable() directly instead of storing it in
another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/499621/
Link: https://lore.kernel.org/r/20220826072821.253150-1-ye.xingchen@zte.com.cn
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
It makes no sense to have the HPD worker in the MSM DSI driver anymore.
It is only queued from the dsi_host_attach/detach() callbacks, where
it plays no useful role. Either way the panel or next bridge will be
present and will report it's status directly.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/498740/
Link: https://lore.kernel.org/r/20220822174417.292926-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The dsi_phy_driver_probe() function has a "goto fail" for no
reason. Change it to just always return directly when it sees an
error. Make this simpler by leveraging dev_err_probe() which is
designed to make code like this shorter / simpler.
NOTE: as part of this, we now pass through error codes directly from
msm_ioremap_size() rather than translating to -ENOMEM. This changed
mostly because it's much more convenient when using dev_err_probe()
and also it's usually encouraged not to hide error codes like the old
code was doing unless there is a good reason. I can't see any reason
why we'd need to return -ENOMEM instead of -EINVAL from the probe
function.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/496324/
Link: https://lore.kernel.org/r/20220804073608.v4.6.I969118a35934a0e5007fe4f80e3e28e9c0b7602a@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
As of the commit 1de452a0ed ("regulator: core: Allow drivers to
define their init data as const") we no longer need to do copying of
regulator bulk data from initdata to something dynamic. Let's take
advantage of that.
In addition to saving some code, this also moves us to using
ARRAY_SIZE() to specify how many regulators we have which is less
error prone.
This gets rid of some layers of wrappers which makes it obvious that
we can get rid of an extra error print.
devm_regulator_bulk_get_const() prints errors for you so you don't
need an extra layer of printing.
In all cases here I have preserved the old settings without any
investigation about whether the loads being set are sensible. In the
cases of some of the PHYs if several PHYs in the same file used
exactly the same settings I had them point to the same data structure.
NOTE: Though I haven't done the math, this is likely an overall
savings in terms of "static const" data. We previously always
allocated space for 8 supplies. Each of these supplies took up 36
bytes of data (32 for name, 4 for an int).
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/496325/
Link: https://lore.kernel.org/r/20220804073608.v4.5.I55a9e65cb1c22221316629e98768ff473f47a067@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
As of commit 6eabfc018e ("regulator: core: Allow specifying an
initial load w/ the bulk API") we can now specify the initial load in
the bulk data rather than having to manually call regulator_set_load()
on each regulator. Let's use it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/496319/
Link: https://lore.kernel.org/r/20220804073608.v4.4.I7b3c72949883846badb073cfeae985c55239da1d@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
As of commit 5451781dad ("regulator: core: Only count load for
enabled consumers"), a load isn't counted for a disabled
regulator. That means all the code in the DSI driver to specify and
set loads before disabling a regulator is not actually doing anything
useful. Let's remove it.
It should be noted that all of the loads set that were being specified
were pointless noise anyway. The only use for this number is to pick
between low power and high power modes of regulators. Regulators
appear to do this changeover at loads on the order of 10000 uA. You
would need a lot of clients of the same rail for that 100 uA number to
count for anything.
Note that now that we get rid of the setting of the load at disable
time, we can just set the load once when we first get the regulator
and then forget it.
It should also be noted that the regulator functions
regulator_bulk_enable() and regulator_set_load() already print error
messages when they encounter problems so while moving things around we
get rid of some extra error prints.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/496320/
Link: https://lore.kernel.org/r/20220804073608.v4.3.If1f94fbbdb7c1d0fb3961de61483a851ad1971a7@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
parent_hw pointers are easier to manage and cheaper to use than
repeatedly formatting the parent name and subsequently leaving the clk
framework to perform lookups based on that name.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/491927/
Link: https://lore.kernel.org/r/20220629225331.357308-12-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
parent_hw pointers are easier to manage and cheaper to use than
repeatedly formatting the parent name and subsequently leaving the clk
framework to perform lookups based on that name.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/491923/
Link: https://lore.kernel.org/r/20220629225331.357308-11-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
parent_hw pointers are easier to manage and cheaper to use than
repeatedly formatting the parent name and subsequently leaving the clk
framework to perform lookups based on that name.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/491921/
Link: https://lore.kernel.org/r/20220629225331.357308-10-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
parent_hw pointers are easier to manage and cheaper to use than
repeatedly formatting the parent name and subsequently leaving the clk
framework to perform lookups based on that name.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/491925/
Link: https://lore.kernel.org/r/20220629225331.357308-9-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
parent_hw pointers are easier to manage and cheaper to use than
repeatedly formatting the parent name and subsequently leaving the clk
framework to perform lookups based on that name.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/491929/
Link: https://lore.kernel.org/r/20220629225331.357308-8-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Now that the last DSI PHY PLL driver (dsi_phy_28nm_8960) has been
converted to use a simple stack-local char-array instead of a
devm_kzalloc heap allocation we can safely call sizeof() on every string
variable (that's now a sized array instead of a pointer) passed into
snprintf instead of hardcoding the size.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/491920/
Link: https://lore.kernel.org/r/20220629225331.357308-7-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
