The fb only deals with kms->vm, so make that explicit. This will start
letting us refcount the # of times the fb is pinned, so we can only
unpin the vma after last user of the fb is done. Having a single
reference count really only works if there is only a single vm.
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Tested-by: Antonino Maniscalco <antomani103@gmail.com>
Reviewed-by: Antonino Maniscalco <antomani103@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/661476/
Re-aligning naming to better match drm_gpuvm terminology will make
things less confusing at the end of the drm_gpuvm conversion.
This is just rename churn, no functional change.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Tested-by: Antonino Maniscalco <antomani103@gmail.com>
Reviewed-by: Antonino Maniscalco <antomani103@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/661466/
Only several SSPP blocks support such features as YUV output or scaling,
thus different DRM planes have different features. Properly utilizing
all planes requires the attention of the compositor, who should
prefer simpler planes to YUV-supporting ones. Otherwise it is very easy
to end up in a situation when all featureful planes are already
allocated for simple windows, leaving no spare plane for YUV playback.
To solve this problem make all planes virtual. Each plane is registered
as if it supports all possible features, but then at the runtime during
the atomic_check phase the driver selects backing SSPP block for each
plane.
As the planes are attached to the CRTC and not the encoder, the SSPP
blocks are also allocated per CRTC ID (all other resources are currently
allocated per encoder ID). This also matches the hardware requirement,
where both rectangles of a single SSPP can only be used with the LM
pair.
Note, this does not provide support for using two different SSPP blocks
for a single plane or using two rectangles of an SSPP to drive two
planes. Each plane still gets its own SSPP and can utilize either a solo
rectangle or both multirect rectangles depending on the resolution.
Note #2: By default support for virtual planes is turned off and the
driver still uses old code path with preallocated SSPP block for each
plane. To enable virtual planes, pass 'msm.dpu_use_virtual_planes=1'
kernel parameter.
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/629022/
Link: https://lore.kernel.org/r/20241215-dpu-virtual-wide-v8-1-65221f213ce1@linaro.org
Unfortunately the tooling doesn't check documents placed before funciton
prototypes. Such comments frequently become outdated, miss several
params, etc. Move documentation for the functions to be placed before
the actual function body, allowing 'make W=1' to actually check these
comments and report an error.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/622690/
Link: https://lore.kernel.org/r/20241102-dpu-docs-rework-v1-1-d735853fd6db@linaro.org
After cleaning up the older multirect support the function
dpu_plane_validate_multirect_v2() is unused. Lets remove it.
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
[DB: also drop struct dpu_multirect_plane_states and R0/R1/R_MAX]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/527348/
Link: https://lore.kernel.org/r/20230316161653.4106395-33-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
It is possible to use multirect feature and split source to use the SSPP
to output two consecutive rectangles. This commit brings in this
capability to support wider screen resolutions.
Tested-by: Abhinav Kumar <quic_abhinavk@quicinc.com> # sc7280
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/527358/
Link: https://lore.kernel.org/r/20230316161653.4106395-28-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Now as all accesses to pipe_cfg and pstate have been cleaned, add
struct dpu_hw_sspp_cfg to struct dpu_plane_state, so that
dpu_plane_atomic_check() and dpu_plane_atomic_update() do not have a
chance to disagree about src/dst rectangles (currently
dpu_plane_atomic_check() uses unclipped rectangles, while
dpu_plane_atomic_update() uses clipped rectangles calculated by
drm_atomic_helper_check_plane_state()).
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Tested-by: Abhinav Kumar <quic_abhinavk@quicinc.com> # sc7280
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/527352/
Link: https://lore.kernel.org/r/20230316161653.4106395-21-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
In preparation to adding fully virtualized planes, move struct
dpu_hw_sspp instance from struct dpu_plane to struct dpu_plane_state, as
it will become a part of state (variable, changes during runtime) rather
than part of a plane (ideally should be statically allocated during boot).
The sspp pointer is set at the dpu_plane_reset(), since this is the
function which allocates the state. Once we have fully virtual
plane<->SSPP relationship, the SSPP will be allocated dynamically in the
dpu_plane_atomic_check() function.
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Tested-by: Abhinav Kumar <quic_abhinavk@quicinc.com> # sc7280
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/527322/
Link: https://lore.kernel.org/r/20230316161653.4106395-6-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
There is no need to keep a separate function for calling into the ctl if
we already know all the details. Inline this function in the dpu_crtc.c
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/473152/
Link: https://lore.kernel.org/r/20220209172520.3719906-7-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Master/virtual planes were used for multirect support. In preparation to
reworking DPU planes, drop support for master planes (which was not used
anyway).
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/473146/
Link: https://lore.kernel.org/r/20220209172520.3719906-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
- Some DPU versions support inline rot90. It is supported only for
limited amount of UBWC formats.
- There are two versions of inline rotators, v1 (present on sm8250 and
sm7250) and v2 (sc7280). These versions differ in the list of supported
formats and in the scaler possibilities.
Co-developed-by: Kalyan Thota <quic_kalyant@quicinc.com>
Signed-off-by: Kalyan Thota <quic_kalyant@quicinc.com>
Signed-off-by: Vinod Polimera <quic_vpolimer@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/481672/
Link: https://lore.kernel.org/r/1649695021-19132-3-git-send-email-quic_vpolimer@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Someone on IRC once asked an innocent enough sounding question: Why
with xf86-video-modesetting is es2gears limited at 120fps.
So I broke out the perfetto tracing mesa MR and took a look. It turns
out the problem was drm_atomic_helper_dirtyfb(), which would end up
waiting for vblank.. es2gears would rapidly push two frames to Xorg,
which would blit them to screen and in idle hook (I assume) call the
DIRTYFB ioctl. Which in turn would do an atomic update to flush the
dirty rects, which would stall until the next vblank. And then the
whole process would repeat.
But this is a bit silly, we only need dirtyfb for command mode DSI
panels. So track in plane state whether dirtyfb is required, and
track in the fb how many attached planes require dirtyfb so that we
can skip it when not required. (Note, mdp4 does not actually have
cmd mode support.)
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220223191118.881321-1-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
The disable_danger debugfs file is not related to a single plane.
Instead it is used by all registered planes. Move it from plane subtree
to the global subtree next to danger_status and safe_status files,
so that the new file supplements them.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/20211201222633.2476780-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Scaler and pixel_ext configuration does not contain a long living state,
it is used only during plane update, so remove these two fields from
dpu_plane_state and allocate them on stack.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/20211201225140.2481577-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Remove struct dpu_hw_pipe_cdp_cfg instance from dpu_plane, it is an
interim configuration structure. Allocate it on stack instead.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210930140002.308628-9-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
dpu_crtc_atomic_flush() was directly poking it's attached planes in a
code path that ended up in dpu_plane_atomic_update(), even if the plane
was not involved in the current atomic update. While a bit dubious,
this worked before because plane->state would always point to something
valid. But now using drm_atomic_get_new_plane_state() we could get a
NULL state pointer instead, leading to:
[ 20.873273] Call trace:
[ 20.875740] dpu_plane_atomic_update+0x5c/0xed0
[ 20.880311] dpu_plane_restore+0x40/0x88
[ 20.884266] dpu_crtc_atomic_flush+0xf4/0x208
[ 20.888660] drm_atomic_helper_commit_planes+0x150/0x238
[ 20.894014] msm_atomic_commit_tail+0x1d4/0x7a0
[ 20.898579] commit_tail+0xa4/0x168
[ 20.902102] drm_atomic_helper_commit+0x164/0x178
[ 20.906841] drm_atomic_commit+0x54/0x60
[ 20.910798] drm_atomic_connector_commit_dpms+0x10c/0x118
[ 20.916236] drm_mode_obj_set_property_ioctl+0x1e4/0x440
[ 20.921588] drm_connector_property_set_ioctl+0x60/0x88
[ 20.926852] drm_ioctl_kernel+0xd0/0x120
[ 20.930807] drm_ioctl+0x21c/0x478
[ 20.934235] __arm64_sys_ioctl+0xa8/0xe0
[ 20.938193] invoke_syscall+0x64/0x130
[ 20.941977] el0_svc_common.constprop.3+0x5c/0xe0
[ 20.946716] do_el0_svc+0x80/0xa0
[ 20.950058] el0_svc+0x20/0x30
[ 20.953145] el0_sync_handler+0x88/0xb0
[ 20.957014] el0_sync+0x13c/0x140
The reason for the codepath seems dubious, the atomic suspend/resume
heplers should handle the power-collapse case. If not, the CRTC's
atomic_check() should be adding the planes to the atomic update.
Reported-by: Stephen Boyd <swboyd@chromium.org>
Reported-by: John Stultz <john.stultz@linaro.org>
Fixes: 37418bf14c ("drm: Use state helper instead of the plane state pointer")
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430171744.1721408-1-robdclark@gmail.com
Update the qos remap only if the client type changes for the plane.
This will avoid unnecessary register programming and also avoid log
spam from the dpu_vbif_set_qos_remap() function.
changes in v2:
- get rid of the dirty flag and simplify the logic to call
_dpu_plane_set_qos_remap()
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This change adds support to scale src clk and bandwidth as
per composition requirements.
Interconnect registration for bw has been moved to mdp
device node from mdss to facilitate the scaling.
Changes in v1:
- Address armv7 compilation issues with the patch (Rob)
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unused functions from dpu plane interface
and unused variables from dpu plane state structure.
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Jayant Shekhar <jshekhar@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reserve DMA pipe for cursor plane and attach it to the
crtc during the initialization.
Changes in V2:
None
Signed-off-by: Sravanthi Kollukuduru <skolluku@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
SDM845 SoC includes the Mobile Display Sub System (MDSS) which is a
top level wrapper consisting of Display Processing Unit (DPU) and
display peripheral modules such as Display Serial Interface (DSI)
and DisplayPort (DP).
MDSS functions essentially as a back-end composition engine. It blends
video and graphic images stored in the frame buffers and scans out the
composed image to a display sink (over DSI/DP).
The following diagram represents hardware blocks for a simple pipeline
(two planes are present on a given crtc which is connected to a DSI
connector):
MDSS
+---------------------------------+
| +-----------------------------+ |
| | DPU | |
| | +--------+ +--------+ | |
| | | SSPP | | SSPP | | |
| | +----+---+ +----+---+ | |
| | | | | |
| | +----v-----------v---+ | |
| | | Layer Mixer (LM) | | |
| | +--------------------+ | |
| | +--------------------+ | |
| | | PingPong (PP) | | |
| | +--------------------+ | |
| | +--------------------+ | |
| | | INTERFACE (VIDEO) | | |
| | +---+----------------+ | |
| +------|----------------------+ |
| | |
| +------|---------------------+ |
| | | DISPLAY PERIPHERALS | |
| | +---v-+ +-----+ | |
| | | DSI | | DP | | |
| | +-----+ +-----+ | |
| +----------------------------+ |
+---------------------------------+
The number of DPU sub-blocks (i.e. SSPPs, LMs, PP blocks and INTFs)
depends on SoC capabilities.
Overview of DPU sub-blocks:
---------------------------
* Source Surface Processor (SSPP):
Refers to any of hardware pipes like ViG, DMA etc. Only ViG pipes are
capable of performing format conversion, scaling and quality improvement
for source surfaces.
* Layer Mixer (LM):
Blend source surfaces together (in requested zorder)
* PingPong (PP):
This block controls frame done interrupt output, EOL and EOF generation,
overflow/underflow control.
* Display interface (INTF):
Timing generator and interface connecting the display peripherals.
DRM components mapping to DPU architecture:
------------------------------------------
PLANEs maps to SSPPs
CRTC maps to LMs
Encoder maps to PPs, INTFs
Data flow setup:
---------------
MDSS hardware can support various data flows (e.g.):
- Dual pipe: Output from two LMs combined to single display.
- Split display: Output from two LMs connected to two separate
interfaces.
The hardware capabilities determine the number of concurrent data paths
possible. Any control path (i.e. pipeline w/i DPU) can be routed to any
of the hardware data paths. A given control path can be triggered,
flushed and controlled independently.
Changes in v3:
- Move msm_media_info.h from uapi to dpu/ subdir
- Remove preclose callback dpu (it's handled in core)
- Fix kbuild warnings with parent_ops
- Remove unused functions from dpu_core_irq
- Rename mdss_phys to mdss
- Rename mdp_phys address space to mdp
- Drop _phys from vbif and regdma binding names
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rajesh Yadav <ryadav@codeaurora.org>
Signed-off-by: Sravanthi Kollukuduru <skolluku@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
[robclark minor rebase]
Signed-off-by: Rob Clark <robdclark@gmail.com>
