The BIOS can leave the AUX power well enabled on an output, even if this
isn't required (on platforms where the AUX power is only needed for an
AUX access). This was observed at least on PTL. To avoid the WARN which
would be triggered by this during the HW readout, convert the WARN to a
debug message.
Cc: stable@vger.kernel.org # v6.8+
Reported-by: Charlton Lin <charlton.lin@intel.com>
Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250811080152.906216-6-imre.deak@intel.com
(cherry picked from commit 6cb52cba474b2bec1a3018d3dbf75292059a29a1)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
Use the cached max lane count value on LNL+, to account for scenarios
where this value is queried after the HW cleared the corresponding pin
assignment value in the TCSS_DDI_STATUS register after the sink got
disconnected.
For consistency, follow-up changes will use the cached max lane count
value on other platforms as well and will also cache the pin assignment
value in a similar way.
Cc: stable@vger.kernel.org # v6.8+
Reported-by: Charlton Lin <charlton.lin@intel.com>
Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250811080152.906216-5-imre.deak@intel.com
(cherry picked from commit afc4e84388079f4d5ba05271632b7a4d8d85165c)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
On LNL+ for a disconnected sink the pin assignment value gets cleared by
the HW/FW as soon as the sink gets disconnected, even if the PHY
ownership got acquired already by the BIOS/driver (and hence the PHY
itself is still connected and used by the display). During HW readout
this can result in detecting the PHY's max lane count as 0 - matching
the above cleared aka NONE pin assignment HW state. For a connected PHY
the driver in general (outside of intel_tc.c) expects the max lane count
value to be valid for the video mode enabled on the corresponding output
(1, 2 or 4). Ensure this by setting the max lane count to 4 in this
case. Note, that it doesn't matter if this lane count happened to be
more than the max lane count with which the PHY got connected and
enabled, since the only thing the driver can do with such an output -
where the DP-alt sink is disconnected - is to disable the output.
v2: Rebased on change reading out the pin configuration only if the PHY
is connected.
Cc: stable@vger.kernel.org # v6.8+
Reported-by: Charlton Lin <charlton.lin@intel.com>
Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250811080152.906216-4-imre.deak@intel.com
(cherry picked from commit 33cf70bc0fe760224f892bc1854a33665f27d482)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
The PHY's pin assignment value in the TCSS_DDI_STATUS register - as set
by the HW/FW based on the connected DP-alt sink's TypeC/PD pin
assignment negotiation - gets cleared by the HW/FW on LNL+ as soon as
the sink gets disconnected, even if the PHY ownership got acquired
already by the driver (and hence the PHY itself is still connected and
used by the display). This is similar to how the PHY Ready flag gets
cleared on LNL+ in the same register.
To be able to query the max lane count value on LNL+ - which is based on
the above pin assignment - at all times even after the sink gets
disconnected, the max lane count must be determined and cached during
the PHY's HW readout and connect sequences. Do that here, leaving the
actual use of the cached value to a follow-up change.
v2: Don't read out the pin configuration if the PHY is disconnected.
Cc: stable@vger.kernel.org # v6.8+
Reported-by: Charlton Lin <charlton.lin@intel.com>
Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250811080152.906216-3-imre.deak@intel.com
(cherry picked from commit 3e32438fc406761f81b1928d210b3d2a5e7501a0)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
The TypeC PHY HW readout during driver loading and system resume
determines which TypeC mode the PHY is in (legacy/DP-alt/TBT-alt) and
whether the PHY is connected, based on the PHY's Owned and Ready flags.
For the PHY to be in DP-alt or legacy mode and for the PHY to be in the
connected state in these modes, both the Owned (set by the BIOS/driver)
and the Ready (set by the HW) flags should be set.
On ICL-MTL the HW kept the PHY's Ready flag set after the driver
connected the PHY by acquiring the PHY ownership (by setting the Owned
flag), until the driver disconnected the PHY by releasing the PHY
ownership (by clearing the Owned flag). On LNL+ this has changed, in
that the HW clears the Ready flag as soon as the sink gets disconnected,
even if the PHY ownership was acquired already and hence the PHY is
being used by the display.
When inheriting the HW state from BIOS for a PHY connected in DP-alt
mode on which the sink got disconnected - i.e. in a case where the sink
was connected while BIOS/GOP was running and so the sink got enabled
connecting the PHY, but the user disconnected the sink by the time the
driver loaded - the PHY Owned but not Ready state must be accounted for
on LNL+ according to the above. Do that by assuming on LNL+ that the PHY
is connected in DP-alt mode whenever the PHY Owned flag is set,
regardless of the PHY Ready flag.
This fixes a problem on LNL+, where the PHY TypeC mode / connected state
was detected incorrectly for a DP-alt sink, which got connected and then
disconnected by the user in the above way.
v2: Rename tc_phy_in_legacy_or_dp_alt_mode() to tc_phy_owned_by_display().
(Luca, Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org # v6.8+
Reported-by: Charlton Lin <charlton.lin@intel.com>
Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
[Imre: Add one-liner function documentation for tc_phy_owned_by_display()]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250811080152.906216-2-imre.deak@intel.com
(cherry picked from commit 89f4b196ee4b056e0e8c179b247b29d4a71a4e7e)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
This is a scripted split of the display related register macros from
i915_reg.h to display/intel_display_regs.h. As a starting point, move
all the macros that are only used in display code (or GVT). If there are
users in core i915 code or soc/, or no users anywhere, keep the macros
in i915_reg.h. This is done in groups of macros separated by blank
lines, moving the comments along with the groups.
Some manually picked macro groups are kept/moved regardless of the
heuristics above.
This is obviously a very crude approach. It's not perfect. But there are
4.2k lines in i915_reg.h, and its refactoring has ground to a halt. This
is the big hammer that splits the file to two, and enables further
cleanup.
Cc: Suraj Kandpal <suraj.kandpal@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com> # v2
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250606102256.2080073-1-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
It's not clear which encoder intel_dp_mst_encoder_active_links() refers
to (primary/stream), but there is also no reason to call the queried
property an encoder property; remove encoder from the name. Also it's
the number of MST streams being queried, vs. the number of MST links
(there is one MST link carrying one or more MST streams), so rename link
to stream as well.
While at it pass intel_dp to the function, which is more logical and
makes it easier to re-use the function later (without the need to get
the digital port pointer).
Also move the function earlier, next to the related ones.
Suggested-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250404150310.1156696-5-imre.deak@intel.com
Forward declare struct drm_printer instead of including drm/drm_print.h,
as we only need the pointer. Turns out quite a few places depend on this
include implicitly. Make them explicit.
Some of the includes are just stale and unnecessary. Group the forward
declarations together while at it.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://lore.kernel.org/r/20250326115452.2090275-1-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Convert the remaining intel_display_power.h interfaces to
take struct intel_display instead of struct drm_i915_private.
intel_display_power.c still has some internal uses due to
i915->runtime_pm.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250211000135.6096-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Pass intel_display to the display power stuff. These are spread
all over the place so tend to hinder clean conversions of whole
files.
TODO: The gt part/unpark power domain shenanigans need some
kind of more abstract interface...
v2: Deal with cmtg
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250206185533.32306-7-ville.syrjala@linux.intel.com
Let's start using struct intel_display instead of struct drm_i915_private
when introducing new code. No functional changes.
v2: Drop tc_to_intel_display() helper function (Jani)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241127073200.124907-3-mika.kahola@intel.com
There is a HW issue that arises when there are race conditions
between TCSS entering/exiting TC7 or TC10 states while the
driver is asserting/deasserting TCSS power request. As a
workaround, Display driver will implement a mailbox sequence
to ensure that the TCSS is in TC0 when TCSS power request is
asserted/deasserted.
The sequence is the following
1. Read mailbox command status and wait until run/busy bit is
clear
2. Write mailbox data value '1' for power request asserting
and '0' for power request deasserting
3. Write mailbox command run/busy bit and command value with 0x1
4. Read mailbox command and wait until run/busy bit is clear
before continuing power request.
v2: Rename WA function (Gustavo)
Limit WA only for PTL platform with a TODO note (Gustavo)
Add TCSS_DISP_MAILBOX_IN_CMD_RUN_BUSY for clarity when writing
register data (Gustavo)
Move register defs from i915_reg.h to intel_cx0_phy_regs.h (Gustavo)
v3: Use "struct intel_display" instead of "struct drm_i915_private" (Jani)
Move defs above C10 definitions in the
intel_cx0_phy_regs.h file (Gustavo)
Move drm_WARN_ON() inside WA function (Gustavo)
Rename workaround function as wa_14020908590() (Gustvo)
Use boolean enable instead of if-else structure (Raag)
v4: Drop drm_WARN_ON() (Raag)
Fix function definition to fit into a single line (Raag)
v5: Drop TCSS_DISP_MAILBOX_IN_CMD_RUN_BUSY from TCSS_DISP_MAILBOX_IN_CMD_DATA(val)
macro (Jani)
Rename WA function with some meaningful name and add comment
on WA number (Jani)
Use struct intel_display on WA calling function (Jani)
Reviewed-by: Raag Jadav <raag.jadav@intel.com> (v4)
Acked-by: Jani Nikula <jani.nikula@intel.com> (v5)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241127073200.124907-2-mika.kahola@intel.com
dig_port->saved_port_bits is used to permanently store two DDI_BUF_CTL
bits, DDI_BUF_PORT_REVERSAL and DDI_A_4_LANES. Store them separately as
bools to make their use more logical and less about storing state as
register bits.
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241129102503.452272-1-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Replace the last few remaining instances of string enable(d)/disable(d)
choices with the linux string choice helpers to avoid further
cocci warnings.
Signed-off-by: Sai Teja Pottumuttu <sai.teja.pottumuttu@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241023054655.4017489-1-sai.teja.pottumuttu@intel.com
Starting with Xe_LPD+, although FIA is still used to readout Type-C pin
assignment, part of Type-C support is moved to PICA and programming
PORT_TX_DFLEXDPMLE1(*) registers is not applicable anymore like it was
for previous display IPs (e.g. see BSpec 49190).
v2:
- Mention Bspec 49190 as a reference of instructions for previous
IPs. (Shekhar Chauhan)
- s/Xe_LPDP/Xe_LPD+/ in the commit message. (Matt Roper)
- Update commit message to be more accurate to the changes in the IP.
(Imre Deak)
Bspec: 65750, 65448
Reviewed-by: Shekhar Chauhan <shekhar.chauhan@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240625202652.315936-1-gustavo.sousa@intel.com
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Some registers for DDI A/B moved to PICA and now follow the same format
as the ones for the PORT_TC ports. The wrapper here deals with 2 issues:
- Share the implementation between xe2lpd and previous
platforms: there are minor layout changes, it's mostly the
register location that changed
- Handle offsets after TC ports
v2:
- Explain better the trick to use just the second range (Matt Roper)
- Add missing conversions after rebase (Matt Roper)
- Use macro instead of inline function, avoiding includes in the
header (Jani)
- Prefix old macros with underscore so they don't get used by mistake,
and name the new ones using the previous names
v3: Use the same logic for the recently-introduced XELPDP_PORT_MSGBUS_TIMER
(Gustavo)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240126224638.4132016-3-lucas.demarchi@intel.com
Glitches deasserting the connector HPD line can lead to incorrectly
detecting a disconnect event (a glitch asserting the line will only
cause a redundant connect->disconnect transition). The source of such a
glitch can be noise on the line or a 0.5ms-1ms MST IRQ_HPD pulse. TypeC
ports in the DP-alt or TBT-alt mode filter out these glitches inernally,
but for others the driver has to do this. Make it so by polling the HPD
line on these connectors for 4 ms.
Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-12-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Add hooks to intel_digital_port to lock and unlock the port and add a
helper to check the connector's detect status while the port is locked
already. This simplifies checking the connector detect status in
intel_dp_aux_xfer() and intel_digital_port_connected() in the next two
patches aborting AUX transfers on all DP connectors (except eDP) and
filtering HPD glitches.
Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-11-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
When going through the disconnection flow we don't need to wait for PHY
readiness and hence we can skip the wait part. For disabling the function
returns false as an indicator that the power is not enabled. After all,
we are not even using the return value when Type-C is disconnecting.
v2: Cleanup for increased readibility (Imre)
BSpec: 65380
For VLK-53734
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231212115130.485911-1-mika.kahola@intel.com
Fix below compiler warning:
intel_tc.c:1879:11: error: ‘%d’ directive output may be truncated
writing between 1 and 11 bytes into a region of size 3
[-Werror=format-truncation=]
"%c/TC#%d", port_name(port), tc_port + 1);
^~
intel_tc.c:1878:2: note: ‘snprintf’ output between 7 and 17 bytes
into a destination of size 8
snprintf(tc->port_name, sizeof(tc->port_name),
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%c/TC#%d", port_name(port), tc_port + 1);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
v2: use kasprintf(Imre)
v3: use const for port_name, and fix tc mem leak(Imre)
Fixes: 3eafcddf76 ("drm/i915/tc: Move TC port fields to a new intel_tc_port struct")
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Nirmoy Das <nirmoy.das@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231026125636.5080-1-nirmoy.das@intel.com
Starting from display version 20, we need to read the pin assignment
from the IOM TCSS_DDI_STATUS register instead of reading it from the
FIA.
We use the pin assignment to decide the maximum lane count. So, to
support this change, add a new lnl_tc_port_get_max_lane_count() function
that reads from the TCSS_DDI_STATUS register and decides the maximum
lane count based on that.
BSpec: 69594
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230919192128.2045154-14-lucas.demarchi@intel.com
It is irrelevant for the caller that the max lane count is being
derived from a FIA register, so having "fia" in the function name is
irrelevant. Rename the function accordingly.
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230825081638.275795-5-luciano.coelho@intel.com
This makes the code a bit more symmetric and readable, especially when
we start adding more display version-specific alternatives.
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230825081638.275795-4-luciano.coelho@intel.com
This function doesn't really return the pin assignment mask, but the
max lane count derived from that. So rename the function to
mtl_tc_port_get_max_lane_count() to better reflect what it really does.
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230825081638.275795-2-luciano.coelho@intel.com
If the output on a DP-alt link with its sink disconnected is kept
enabled for too long (about 20 sec), then some IOM/TCSS firmware timeout
will cause havoc on the PCI bus, at least for other GFX devices on it
which will stop powering up. Since user space is not guaranteed to do a
disabling modeset in time, switch such disconnected but active links to
TBT mode - which is without such shortcomings - with a 2 second delay.
If the above condition is detected already during the driver load/system
resume sanitization step disable the output instead, as at that point no
user space or kernel client depends on a consistent output state yet and
because subsequent atomic modeset on such connectors - without the
actual sink capabilities available - can fail.
An active/disconnected port as above will also block the HPD status of
other active/disconnected ports to get updated (stuck in the connected
state), until the former port is disabled, its PHY is disconnected and
a ~10 ms delay has elapsed. This means the link state for all TypeC
ports/CRTCs must be rechecked after a CRTC is disabled due to the above
reason. For this disconnect the PHY synchronously after the CRTC/port is
disabled and recheck all CRTCs for the above condition whenever such a
port is disabled.
To account for a race condition during driver loading where the sink is
disconnected after the above sanitization step and before the HPD
interrupts get enabled, do an explicit check/link reset if needed from
the encoder's late_register hook, which is called after the HPD
interrupts are enabled already.
v2:
- Handle an active/disconnected port blocking the HPD state update of
another active/disconnected port.
- Cancel the delayed work resetting the link also from the encoder
enable/suspend/shutdown hooks.
- Rebase on the earlier intel_modeset_lock_ctx_retry() addition,
fixing here the missed atomic state reset in case of a retry.
- Fix handling of an error return from intel_atomic_get_crtc_state().
- Recheck if the port needs to be reset after all the atomic state
is locked and async commits are waited on.
v3:
- Add intel_crtc_needs_link_reset(), instead of open-coding it,
keep intel_crtc_has_encoders(). (Ville)
- Fix state dumping and use a bitmask to track disabled CRTCs in
intel_sanitize_all_crtcs(). (Ville)
- Set internal in intel_atomic_state right after allocating it.
(Ville)
- Recheck all CRTCs (not yet force-disabled) after a CRTC is
force-disabled for any reason (not only due to a link state)
in intel_sanitize_all_crtcs().
- Reduce delay after CRTC disabling to 20ms, and use the simpler
msleep().
- Clarify code comment about HPD behaviour in
intel_sanitize_all_crtcs().
- Move all the TC link reset logic to intel_tc.c .
- Cancel the link reset work synchronously during system suspend,
driver unload and shutdown.
v4:
- Rebased on previous patch, which allows calling the TC port
suspend/cleanup handlers without modeset locks held; remove the
display driver suspended assert from the link reset work
accordingly.
v5: (Ville)
- Remove reset work canceling from intel_ddi_pre_pll_enable().
- Track a crtc vs. pipe mask in intel_sanitize_all_crtcs().
- Add reset_link_commit() to clarify the
intel_modeset_lock_ctx_retry loop.
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5860
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512195513.2699-2-imre.deak@intel.com
Unlike previous platforms that used PORT_TX_DFLEXDPSP
for max_lane calculation, MTL uses only PORT_TX_DFLEXPA1
from which the max_lanes has to be calculated.
Bspec: 50235, 65380
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Jose Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-13-mika.kahola@intel.com
The HPD live status for MTL has to be read from different set of
registers. MTL deserves a new function for this purpose
and cannot reuse the existing HPD live status detection
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-12-mika.kahola@intel.com
Add register writes to enable powering up Type-C subsystem i.e. TCSS.
For MeteorLake we need to request TCSS to power up and check the TCSS
power state after 500 us.
In addition, for PICA we need to set/clear the Type-C PHY ownnership
bit when Type-C device is connected/disconnected.
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-11-mika.kahola@intel.com
There's not much point in a static work function having a kernel-doc
comment. Just clean it up and make it a regular comment.
This fixes the kernel-doc warnings:
drivers/gpu/drm/i915/display/intel_tc.c:1370: warning: Function
parameter or member 'work' not described in
'intel_tc_port_disconnect_phy_work'
drivers/gpu/drm/i915/display/intel_tc.c:1370: warning: Excess function
parameter 'dig_port' description in 'intel_tc_port_disconnect_phy_work'
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230405104142.766598-1-jani.nikula@intel.com
Bspec has updated the TC connect/disconnect sequences, add the required
platform hooks for these.
The difference wrt. the old sequence is the order of taking the PHY
ownership - while holding a port power reference this requires - and
blocking the TC-cold power state.
Bspec: 49294
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-26-imre.deak@intel.com
Enable the power required for the HPD live status register access
instead of depending on the caller blocking the TC-cold power state
(during HW readout and connector probing).
A follow up patch will remove connecting/disconnecting the PHY around
connector probing, so querying the HPD status can happen in this case
without TC-cold being blocked.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-24-imre.deak@intel.com
The spec says to use the CPU ISR registers for DP-alt/TBT HPD detection
on ADLP, so do that instead of using the related IOM/TCSS registers.
Bspec: 55480, 55482, 49212, 49305
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-23-imre.deak@intel.com
Add a hook for platform specific PHY initialization. Move the detection
of modular FIAs to the TGL handler, skipping this on ADLP+ where the
FIAs are always modular, not requiring a detection.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-22-imre.deak@intel.com
Add an assert to each TC PHY hook that their required power domain is
enabled.
While at it add a comment describing the domains used on each platform
and TC mode.
v2: Fix non kernel-doc multiline comments. (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-21-imre.deak@intel.com
Simplify tc_cold_block()/unblock() by dropping their power domain
parameter. The power domain depends on the current TC mode, which -
after the previous patch - can't change while the PHY is connected,
holding a TC-cold-off power domain reference. Based on this the domain
can be deducted from the current TC mode instead of having to pass this
as a parameter.
Blocking TC-cold for the PHY HW readout happens before the current TC
mode is determined, so here the initial power domain must be still
manually passed.
For debugging still keep track of the domain used for tc_cold_block()
and verify that it remained the same until tc_cold_unblock().
While at it rename tc_cold_get_power_domain() to
tc_phy_cold_off_domain(), reflecting the name of platform specific hook
added in the next patch.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-19-imre.deak@intel.com
Move blocking/unblocking the TC-cold power state to the platform
specific PHY connect / disconnect hooks. This allows for adjusting the
connect/disconnect sequence as required for each platform.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-17-imre.deak@intel.com
After the previous patch the TC mode in the connect/disconnect functions
is always in sync with the VBT legacy port flag, so for consistency with
the rest of the function check the TC mode instead of the VBT flag.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-16-imre.deak@intel.com
A follow-up patch simplifies the tc_cold_block()/unblock() functions,
dropping the power domain parameter. For this it must be ensured that
the power domain - which depends on the actual TC mode and so the VBT
legacy port flag - can't change while the PHY is in a connected state
and accordingly TC-cold is blocked. Make this so, by fixing up the VBT
legacy flag only in the disconnected TC mode, instead of whenever the
HPD state is retrieved.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-15-imre.deak@intel.com
Factor out a function verifying the PHY connected state in legacy or
DP-alt mode. This is common to all platforms, which can be reused in
platform specific connect hooks added in follow-up patches.
No functional changes.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-13-imre.deak@intel.com
Add generic handlers to connect/disconnect a PHY.
Setting the TC mode to the target mode deducted from the HPD state and -
if connecting to this mode fails - falling back to connecting to the
default (TBT) mode are common to all platforms; move the logic for this
from the ICL specific connect / disconnect handlers to the generic ones.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-12-imre.deak@intel.com
