The current comment fails to clarify why we only accept
the "range limits only" variant of the range descriptor.
Reword it to make some actual sense.
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220927170006.27855-2-ville.syrjala@linux.intel.com
Replace multiple log lines with a single log line at the end of
parsing HF-VSDB. Also use drm_dbg_kms instead of DRM_DBG_KMS, and
add log for DSC1.2 support.
v2: Fixed the formatting issues in the logging (Jani).
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916100551.2531750-5-ankit.k.nautiyal@intel.com
DSC capabilities are given in bytes 11-13 of VSDB (i.e. bytes 8-10 of
SCDS). Since minimum length of Data block is 7, all bytes greater than 7
must be read only after checking the length of the data block.
This patch adds check for data block length before reading relavant DSC
bytes.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916100551.2531750-4-ankit.k.nautiyal@intel.com
HF-VSDB/SCDB has bits to advertise support for 16, 12 and 10 bpc.
If none of the bits are set, the minimum bpc supported with DSC is 8.
This patch corrects the min bpc supported to be 8, instead of 0.
Fixes: 76ee7b9056 ("drm/edid: Parse DSC1.2 cap fields from HFVSDB block")
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
v2: s/DSC1.2/DSC 1.2
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916100551.2531750-2-ankit.k.nautiyal@intel.com
EDID 1.4 introduced some extra flags in the range
descriptor to support min/max h/vfreq >= 255. Consult them
to correctly parse the vfreq limits.
Note that some combinations of the flags are documented
as "reserved" (as are some other values in the descriptor)
but explicitly checking for those doesn't seem particularly
worthwile since we end up with bogus results whether we
decode them or not.
v2: Increase the storage to u16 to make it work (Jani)
Note the "reserved" values situation (Jani)
v3: Document the EDID version number in the defines
Drop some bogus (u8) casts
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/6519
References: https://gitlab.freedesktop.org/drm/intel/-/issues/6484
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220826213501.31490-2-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Split luminance min/max calculation using static hdr metadata from
drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c:update_connector_ext_caps
into drm/drm_edid.c and use it during edid parsing. Calculated range is
stored into connector->display_info->luminance_range.
Add new data structure (drm_luminance_range_inf) to store luminance range
calculated using data from EDID's static hdr metadata block. Add this new
struct as a part of drm_display_info struct.
v3: Squashed adding drm_luminance_range_info patch here
v2: Calculate range during edid parsing
Cc: Roman Li <roman.li@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220719095700.14923-2-jouni.hogander@intel.com
HDMI 2.1 section 10.3.6 defines an HDMI Forum EDID Extension Override
Data Block, which may contain a different extension count than the base
block claims. Add support for reading more EDID data if available. The
extra blocks aren't parsed yet, though.
Hard-coding the EEODB parsing instead of using the iterators we have is
a bit of a bummer, but we have to be able to do this on a partially
allocated EDID while reading it.
v2:
- Check for CEA Data Block Collection size (Ville)
- Amend commit message and comment about hard-coded parsing
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/57b57a355d62eb91ad1e3cf555978576f2bd9fdd.1656494768.git.jani.nikula@intel.com
Unfortunately, there are still plenty of interfaces around that require
a struct edid pointer, and it's impossible to change them all at
once. Add an accessor to the raw EDID data to help the transition.
While there are no such cases now, be defensive against raw EDID
extension count indicating bigger EDID than is actually allocated.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/fb55d0b580d556bf2b8e58070239657ac9cb4b2f.1656494768.git.jani.nikula@intel.com
Add a new function drm_edid_connector_update() to replace the
combination of calls drm_connector_update_edid_property() and
drm_add_edid_modes(). Usually they are called in the drivers in this
order, however the former needs information from the latter.
Since the new drm_edid_read*() functions no longer call the connector
updates directly, and the read and update are separated, we'll need this
new function for the connector update.
This is all in drm_edid.c simply to keep struct drm_edid opaque.
v2:
- Share code with drm_connector_update_edid_property() (Ville)
- Add comment about override EDID handling
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/75aa3dbc8c9aa26ebbcdeacd98a466ef8d8827f4.1656494768.git.jani.nikula@intel.com
Add functions drm_edid_override_set() and drm_edid_override_reset() to
support "edid_override" connector debugfs, and to hide the details about
it in drm_edid.c. No functional changes at this time.
Also note in the connector.override_edid flag kernel-doc that this is
only supposed to be modified by the code doing debugfs EDID override
handling. Currently, it is still being modified by amdgpu in
create_eml_sink() and handle_edid_mgmt() for reasons unknown. This was
added in commit 4562236b3b ("drm/amd/dc: Add dc display driver (v2)")
and later moved to amdgpu_dm.c in commit e7b07ceef2 ("drm/amd/display:
Merge amdgpu_dm_types and amdgpu_dm").
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8f6b4001630cafac5f44aa5913429ac9979743d2.1656494768.git.jani.nikula@intel.com
Add new functions drm_edid_read(), drm_edid_read_ddc(), and
drm_edid_read_custom() to replace drm_get_edid() and drm_do_get_edid()
for reading the EDID. The transition is expected to happen over a fairly
long time.
Note that the new drm_edid_read*() functions do not do any of the
connector updates anymore. The reading and parsing will be completely
separated from each other.
Add new functions drm_edid_alloc(), drm_edid_dup(), and drm_edid_free()
for allocating and freeing drm_edid containers.
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/5a6532a94cad6a79424f6d1918dbe7b7d607ac03.1654674560.git.jani.nikula@intel.com
The CTA Data Block Collection is valid only for CTA extension version
3. In versions 1 and 2, it is a reserved block, which we ignore.
The DTD start offset (byte 2, or d in CTA-861 spec), which determines
the CTA Data Block Collection size, is specified slightly differently
for different versions:
Version 1:
d = offset for the byte following the reserved data block. If no
data is provided in the reserved data block, then d=4. If no DTDs
are provided, then d=0
Version 2:
d = offset for the byte following the reserved data block. If no
data is provided in the reserved data block, then d=4. If d=0, then
no detailed timing descriptors are provided, and no data is provided
in the reserved data block.
Version 3:
d = offset for the byte following the data block collection. If no
data is provided in the data block collection, then d=4. If d=0,
then no detailed timing descriptors are provided, and no data is
provided in the data block collection.
Ever since commit 9e50b9d55e ("drm: edid: Add some bounds checking"),
we've interpreted 0 to mean there are no DTDs but it's all Data
Blocks. Per the spec, Data Blocks are only valid for version 3, where we
should interpret 0 to mean there are no data blocks.
Follow the spec (and hope the EDIDs follow it too).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2a4c94417f024cbafc5d4ca0a74e4617fc4325d1.1654674560.git.jani.nikula@intel.com
We'll need to propagate drm_edid everywhere. This is a clunky start, but
a start nonetheless. We'll eventually convert all of the EDID parsing to
struct drm_edid.
Initially, we'll just create the struct drm_edid in stack. This will be
the compat layer for legacy struct edid code. In the future, we'll have
EDID read return drm_edid objects.
v2: Add legacy init helper.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/000452fddedbaf7f473ac25d4dde2502e60b8e39.1652097712.git.jani.nikula@intel.com
Introduce new opaque type struct drm_edid to encapsulate the EDID data
and the size allocated for it. The contents will be private to
drm_edid.c.
There are a number of reasons for adding a container around struct edid:
* struct edid is a raw blob pointer to data that usually originates
outside of the kernel. Its size is contained within the structure.
* There's no way to attach meta information (such as allocated memory
size) to struct edid.
* Validation of the EDID blob and its size become crucial, and it's
spread all over the subsystem, with varying levels of accuracy.
* HDMI Forum has introduced an HF-EEODB extension that defines an
override EDID size within an EDID extension. The size allocated for an
EDID depends on whether the allocator understands the HF-EEODB
extension. Given a struct edid *, it's impossible to know how much
memory was actually allocated for it.
There are also some reasons for making the container type struct
drm_edid opaque and private to drm_edid.c:
* Have only one place for creating and parsing the EDID, to avoid
duplicating bugs.
* Prepare for reading a pure DisplayID 2.0 from its own DDC address, and
adding it within the same struct drm_edid container, transparently,
and for all drivers.
* With the idea that the drm_edid objects are immutable during their
lifetimes, it will be possible to refcount them and reduce EDID
copying everywhere (this is left for future work).
Initially, just add the type. In follow-up, we'll start converting the
guts of drm_edid.c to use it, and finally add interfaces around it.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f3ecabd8a219aea678ad00f7bcdecf77b27b3c78.1652097712.git.jani.nikula@intel.com
Convert drm_find_cea_extension() to a predicate function to check if the
EDID has a CTA extension or a DisplayID CTA data block. This is mainly
to avoid adding new users that only find the first CTA extension.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a5bf228942e6bd0fc70d5cf7a14c249a14a7afcd.1651569697.git.jani.nikula@intel.com
The DisplayID CTA data block version does not necessarily match the CTA
revision. Simplify by postponing drm_edid_to_eld() slightly, and reusing
the CTA revision extracted by drm_parse_cea_ext().
By not bailing out early in drm_edid_to_eld() we may end up filling
meaningless data to the ELD. However, the main decision for audio is not
the ELD, but rather drm_detect_monitor_audio() called by drivers.
(Arguably a future cleanup could do that in drm_add_edid_modes() and
cache the result in the connector.)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/163ebbfd765066acbfc267256fb3b67fc711a78d.1651569697.git.jani.nikula@intel.com
Convert drm_find_cea_extension() to EDID block iterator in color format
and CTA revision detection. Detect them in all CTA extensions.
Also parse CTA Data Blocks in DisplayID even if there's no CTA EDID
extension.
v2:
- Don't assume DRM_COLOR_FORMAT_RGB444 support if there's only DisplayID
CTA Data Blocks (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220505105242.1198521-1-jani.nikula@intel.com
Iterate through all CTA data blocks across all CTA extensions and
DisplayID data blocks. This may gather more data than before, and if
there's duplicated data, some is overwritten by whichever comes last.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8bdc67aa731857111eddd08a9c192d41d40b5f5a.1651569697.git.jani.nikula@intel.com
Abstract helpers for matching vendor data blocks and extended tags, and
use them to simplify all the cea_db_is_*() functions.
Take void pointer as parameter to allow transitional use for both u8 *
and struct cea_db *.
v2: Remove superfluous parens (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b6bb813afc35c763e744c6cdb4a787da3adf910b.1651569697.git.jani.nikula@intel.com
Find HF-SCDB information in CEA extensions block. And retrieve
Max_TMDS_Character_Rate that support by sink device.
v2: HF-SCDB and HF-VSDBS carry the same SCDS data. Reuse
drm_parse_hdmi_forum_vsdb() to parse this packet.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: intel-gfx <intel-gfx@lists.freedesktop.org>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2bf7110cdb56d5dda311480787faf472c9802de4.1651569697.git.jani.nikula@intel.com
Fix the below drm/edid kernel-doc warnings:
drivers/gpu/drm/drm_edid.c:1589: warning: Function parameter or member '_edid' not described in 'drm_edid_header_is_valid'
drivers/gpu/drm/drm_edid.c:1589: warning: Excess function parameter 'raw_edid' description in 'drm_edid_header_is_valid'
drivers/gpu/drm/drm_edid.c:1737: warning: Function parameter or member '_block' not described in 'drm_edid_block_valid'
drivers/gpu/drm/drm_edid.c:1737: warning: Excess function parameter 'raw_edid' description in 'drm_edid_block_valid'
drivers/gpu/drm/drm_edid.c:2136: warning: Function parameter or member 'read_block' not described in 'drm_do_get_edid'
drivers/gpu/drm/drm_edid.c:2136: warning: Function parameter or member 'context' not described in 'drm_do_get_edid'
drivers/gpu/drm/drm_edid.c:2136: warning: Excess function parameter 'get_edid_block' description in 'drm_do_get_edid'
drivers/gpu/drm/drm_edid.c:2136: warning: Excess function parameter 'data' description in 'drm_do_get_edid'
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
References: https://lore.kernel.org/r/20220406154431.567414c3@canb.auug.org.au
References: https://lore.kernel.org/r/20220420162431.2b28ddea@canb.auug.org.au
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Simon Ser <contact@emersion.fr>
Link: https://patchwork.freedesktop.org/patch/msgid/20220426091913.1339941-1-jani.nikula@intel.com
SCDC is the Status and Control Data Channel for HDMI. Move the SCDC
helpers into display/ and split the header into files for core and
helpers. Update all affected drivers. No functional changes.
To avoid the proliferation of Kconfig options, SCDC is part of DRM's
support for HDMI. If necessary, a new option could make SCDC an
independent feature.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-9-tzimmermann@suse.de
Move DRM's HMDI helpers into the display/ subdirectoy and add it
to DRM's display helpers. Update all affected drivers. No functional
changes.
The HDMI helpers were implemented in the EDID and connector code, but
are actually unrelated. With the move to the display-helper library, we
can remove the dependency on drm_edid.{c,h} in some driver's HDMI source
files.
Several of the HDMI helpers remain in EDID code because both share parts
of their implementation internally. With better refractoring of the EDID
code, those HDMI helpers could be moved into the display-helper library
as well.
v3:
* fix Kconfig dependencies (Javier)
v2:
* reduce HDMI helpers to avoid exporting functions (Jani)
* fix include statements (Jani, Javier)
* update Kconfig symbols
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-8-tzimmermann@suse.de
Add some helpers to figure out the EDID extension block count, block
count, size, pointers to blocks.
Unfortunately, we'll need to cast away the const in a few places where
we actually need to access the data.
v3: fix (!edid_extension_block_count(edid) == 0) (kernel test robot)
v2: fix s/j/i/ introduced in a rebase
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/dc7b0850293d837439fb3914c8a9d81e39018b4b.1649685475.git.jani.nikula@intel.com
Convert drm_do_get_edit() from the base block read helper to the generic
block read helper. There's quite a bit going on here, as the corrupt and
null EDID information is moved back to the caller. As we see, they were
not all that clear to begin with, and this change underlines that.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3bcf98453770757ee93386da0cfbc6552d42a312.1649685475.git.jani.nikula@intel.com
We have an abstraction for the EDID base block read, yet duplicating the
retries and error handling for extension block reads. Introduce a more
generic EDID block read helper.
Switch to the helper piecemeal, starting with drm_edid_get_panel_id(),
which doesn't need or have access to the connector anyway.
The subtle change is switching from drm_edid_block_valid() to
edid_block_check(). We also status print once, not for every attempt.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/47560f7530e4a7b32b56cb9038178244fe30a4af.1649685475.git.jani.nikula@intel.com
Split out a function to log EDID block status. The printouts get changed
slightly.
Unfortunately, not all users will have struct drm_device available, so
we convert to pr_* debug logging instead of drm device based logging.
v2: Complain more loudly about unknown status codes (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/98d12db95e55e2e18548822078ec3b16ae006732.1649685475.git.jani.nikula@intel.com
Initialize on-stack modes with drm_mode_init() to guarantee
no stack garbage in the list head, or that we aren't copying
over another mode's list head.
Based on the following cocci script, with manual fixups:
@decl@
identifier M;
expression E;
@@
- struct drm_display_mode M = E;
+ struct drm_display_mode M;
@@
identifier decl.M;
expression decl.E;
statement S, S1;
@@
struct drm_display_mode M;
... when != S
+ drm_mode_init(&M, &E);
+
S1
@@
expression decl.E;
@@
- &*E
+ E
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218100403.7028-22-ville.syrjala@linux.intel.com
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
There's no need to handle complicated scenarios or debug log when
filtering blocks that have already been identified as invalid. Simplify
by adding an edid_block_valid() helper that operates on const data and
prints nothing.
(Finally, here's the justification for the previously added separate
edid_block_status_valid() function!)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/aa25131c3454c7dbc1e8fdb46549f3787bdf6354.1648752228.git.jani.nikula@intel.com
Add edid_block_check() that only checks the EDID block validity, without
any actions. Turns out it's simple and crystal clear.
Rewrite drm_edid_block_valid() around it, keeping all the functionality
fairly closely the same, warts and all. Turns out it's incredibly
complicated for a function you'd expect to be simple, with all the
fixing and printing and special casing. (Maybe we'll want to simplify it
in the future.)
To slightly simplify, drop the warning for EDID minor revisions > 4.
v2:
- Fix edid_fixup clamp (Ville)
- s/base/is_base_block/ (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b7d108b69acccb7dccbdecc0ca06c2b3ca2e33ca.1648752228.git.jani.nikula@intel.com
Have two clear functions, one to compute the checksum over the EDID, and
another to get the checksum from the EDID. Throw away the diff function.
Ditch the drm_ prefix for static functions, and accept const void * to
help transition to struct edid * usage.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/36641401c8eb0e403c0e33365ff4ad9a28f9fd4a.1648752228.git.jani.nikula@intel.com
The invalid EDID block filtering uses the number of valid EDID
extensions instead of all EDID extensions for looping the extensions in
the copy. This is fine, by coincidence, if all the invalid blocks are at
the end of the EDID. However, it's completely broken if there are
invalid extensions in the middle; the invalid blocks are included and
valid blocks are excluded.
Fix it by modifying the base block after, not before, the copy.
Fixes: 14544d0937 ("drm/edid: Only print the bad edid when aborting")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220330170426.349248-1-jani.nikula@intel.com
We'll want to keep the EDID immutable while parsing. Stop modifying the
EDID because of the quirks.
In theory, this does have userspace implications, but the userspace is
supposed to use the modes exposed via KMS API, not by parsing the EDID
directly.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/45d5cf067eaad49b321ac82836090d9de524374e.1648477901.git.jani.nikula@intel.com
Only an EDID CEA extension has byte #3, while the CTA DisplayID Data
Block does not. Don't interpret bogus data for color formats.
For most displays it's probably an unlikely scenario you'd have a CTA
DisplayID Data Block without a CEA extension, but they do exist.
Fixes: e28ad544f4 ("drm/edid: parse CEA blocks embedded in DisplayID")
Cc: <stable@vger.kernel.org>
Cc: Shawn C Lee <shawn.c.lee@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220323100438.1757295-1-jani.nikula@intel.com
Tag code stored in bit7:5 for CTA block byte[3] is not the same as
CEA extension block definition. Only check CEA block has
basic audio support.
v3: update commit message.
Cc: stable@vger.kernel.org
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Shawn C Lee <shawn.c.lee@intel.com>
Cc: intel-gfx <intel-gfx@lists.freedesktop.org>
Signed-off-by: Cooper Chiou <cooper.chiou@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Fixes: e28ad544f4 ("drm/edid: parse CEA blocks embedded in DisplayID")
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220324061218.32739-1-shawn.c.lee@intel.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmIb/PEeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGugMH/R8icwG5gOjAuxBr
fuz9032ECVFS36Cy3ps9Eqgf5EdS4G6yz3joM4aNtp4B7e5FzI9lzBaHS8OAguNL
y7puFtBr9CywsnniJumZzciB9pEHmF/yyEKfMlRZA3JsRfLDacFstETp+duJnXoA
+s49IWsy1ot5zoherhDXcFLqDoFhLVU4hYwE1xpLpW/cllqmSnW8SDZMtWW1Ui/B
Of7zqINR4zBMmRjP4ymGq/ZrPWlFyWLdtOo0xxVoAQkeMgm33kfaaeGzfyK25FqR
JDGUZ7lkKvwz3PYh2hqJ7dc5K+vhJ18I+F1UmOiL6QAAUF/k8jq7i3Qaf6MKqh2Z
2v+A5k0=
=Hiar
-----END PGP SIGNATURE-----
Backmerge tag 'v5.17-rc6' into drm-next
This backmerges v5.17-rc6 so I can merge some amdgpu and some tegra changes on top.
Signed-off-by: Dave Airlie <airlied@redhat.com>
In order to fill the drm_display_info structure each time an EDID is
read, the code currently will call drm_add_display_info with the parsed
EDID.
drm_add_display_info will then call drm_reset_display_info to reset all
the fields to 0, and then set them to the proper value depending on the
EDID.
In the color_formats case, we will thus report that we don't support any
color format, and then fill it back with RGB444 plus the additional
formats described in the EDID Feature Support byte.
However, since that byte only contains format-related bits since the 1.4
specification, this doesn't happen if the EDID is following an earlier
specification. In turn, it means that for one of these EDID, we end up
with color_formats set to 0.
The EDID 1.3 specification never really specifies what it means by RGB
exactly, but since both HDMI and DVI will use RGB444, it's fairly safe
to assume it's supposed to be RGB444.
Let's move the addition of RGB444 to color_formats earlier in
drm_add_display_info() so that it's always set for a digital display.
Fixes: da05a5a71a ("drm: parse color format support for digital displays")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220203115416.1137308-1-maxime@cerno.tech
Even though we have the other drm_display_info fields reset, the DC
modes are missing.
This shouldn't be an issue since it's explicitly reset every time a new
EDID is parsed.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220125093251.594772-1-maxime@cerno.tech
Per VESA DisplayID Standard v2.0: Type VII Timing – Detailed Timing Data
Definitions were already provided as type I, but not used
Signed-off-by: Yaroslav Bolyukin <iam@lach.pw>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220123191955.57994-1-iam@lach.pw
The current code assumes that the RGB444 and YUV444 formats are the
same, but the HDMI 2.0 specification states that:
The three DC_XXbit bits above only indicate support for RGB 4:4:4 at
that pixel size. Support for YCBCR 4:4:4 in Deep Color modes is
indicated with the DC_Y444 bit. If DC_Y444 is set, then YCBCR 4:4:4
is supported for all modes indicated by the DC_XXbit flags.
So if we have YUV444 support and any DC_XXbit flag set but the DC_Y444
flag isn't, we'll assume that we support that deep colour mode for
YUV444 which breaks the specification.
In order to fix this, let's split the edid_hdmi_dc_modes field in struct
drm_display_info into two fields, one for RGB444 and one for YUV444.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: d0c94692e0 ("drm/edid: Parse and handle HDMI deep color modes.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-4-maxime@cerno.tech
The current code, when parsing the EDID Deep Color depths, that the
YUV422 cannot be used, referring to the HDMI 1.3 Specification.
This specification, in its section 6.2.4, indeed states:
For each supported Deep Color mode, RGB 4:4:4 shall be supported and
optionally YCBCR 4:4:4 may be supported.
YCBCR 4:2:2 is not permitted for any Deep Color mode.
This indeed can be interpreted like the code does, but the HDMI 1.4
specification further clarifies that statement in its section 6.2.4:
For each supported Deep Color mode, RGB 4:4:4 shall be supported and
optionally YCBCR 4:4:4 may be supported.
YCBCR 4:2:2 is also 36-bit mode but does not require the further use
of the Deep Color modes described in section 6.5.2 and 6.5.3.
This means that, even though YUV422 can be used with 12 bit per color,
it shouldn't be treated as a deep color mode.
This is also broken with YUV444 if it's supported by the display, but
DRM_EDID_HDMI_DC_Y444 isn't set. In such a case, the code will clear
color_formats of the YUV444 support set previously in
drm_parse_cea_ext(), but will not set it back.
Since the formats supported are already setup properly in
drm_parse_cea_ext(), let's just remove the code modifying the formats in
drm_parse_hdmi_deep_color_info()
Fixes: d0c94692e0 ("drm/edid: Parse and handle HDMI deep color modes.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-3-maxime@cerno.tech
The drm_hdmi_avi_infoframe_colorspace() function actually sets the
colorimetry and extended_colorimetry fields in the hdmi_avi_infoframe
structure with DRM_MODE_COLORIMETRY_* values.
To make things worse, the hdmi_avi_infoframe structure also has a
colorspace field used to signal whether an RGB or YUV output is being
used.
Let's remove the inconsistency and allow for the colorspace usage by
renaming the function.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-2-maxime@cerno.tech
Improve non-desktop quirk logging if the EDID indicates non-desktop. If
both are set, note about redundant quirk. If there's no quirk but the
EDID indicates non-desktop, don't log non-desktop is set to 0.
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Philipp Zabel <philipp.zabel@gmail.com>
Tested-by: Philipp Zabel <philipp.zabel@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211228101051.317989-1-jani.nikula@intel.com
Now that there is support for the Microsoft VSDB for HMDs, remove the
non-desktop quirk for two devices that are verified to contain it in
their EDID: HPN-3515 and LEN-B800.
Presumably most of the other Windows Mixed Reality headsets contain it
as well, but there are ACR-7FCE and SEC-5194 devices without it.
Tested with LEN-B800.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220123101653.147333-2-philipp.zabel@gmail.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmF298ceHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGIJYH/1rsEFQQ6caeQdy1
z9eFIe48DNM4l7bFk+qEj2UAbzPdahVJ299Mg5fW0n2CDemOc9/n0b9TxQ37YObi
mOzu0xwJVupIxkyFMPQSSc2q8aLm67NSpJy08DsmaNses5hSvu8x15RPHLQTybjt
SwtKns+jpCq79P1GWbrB5e5UkLb0VNoxNp4L1U4pMrYGcEkJUXbaxNY2V/JcXdM7
Vtn+qN0T/J6V6QVftv0t8Ecj3bjEnmL3kZHaTaNg3dGeKRpCGyHc5lcBQ0cNFG6t
vjZ9VbuhBzGI3TN2tHH5hpA1UXo7HPBBCwQqxF1jeGLGHULikYwZ3TAPWqL3QZqC
9cxr9SY=
=p75d
-----END PGP SIGNATURE-----
BackMerge tag 'v5.15-rc7' into drm-next
The msm next tree is based on rc3, so let's just backmerge rc7 before pulling it in.
Signed-off-by: Dave Airlie <airlied@redhat.com>
In commit e11f5bd822 ("drm: Add support for DP 1.4 Compliance edid
corruption test") the function connector_bad_edid() started assuming
that the memory for the EDID passed to it was big enough to hold
`edid[0x7e] + 1` blocks of data (1 extra for the base block). It
completely ignored the fact that the function was passed `num_blocks`
which indicated how much memory had been allocated for the EDID.
Let's fix this by adding a bounds check.
This is important for handling the case where there's an error in the
first block of the EDID. In that case we will call
connector_bad_edid() without having re-allocated memory based on
`edid[0x7e]`.
Fixes: e11f5bd822 ("drm: Add support for DP 1.4 Compliance edid corruption test")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211005192905.v2.1.Ib059f9c23c2611cb5a9d760e7d0a700c1295928d@changeid
Signed-off-by: Dave Airlie <airlied@redhat.com>
- fbdev/efifb: Release PCI device's runtime PM ref during FB destr\
oy (Imre)
i915 Core Driver Changes:
- Only access SFC_DONE in media when not fused off for graphics 12 and newer.
- Double Memory latency values from pcode for DG2 (Matt Roper)
- ADL-S PCI ID update (Tejas)
- New DG1 PCI ID (Jose)
- Fix regression with uncore refactoring (Dave)
i915 Display Changes:
- ADL-P display (XE_LPD) fixes and updates (Ankit, Jani, Matt Roper, Anusham, Jose, Imre, Vandita)
- DG2 display fixes (Ankit, Jani)
- Expand PCH_CNP tweaked display workaround to all newer displays (Anshuman)
- General display simplifications and clean-ups (Jani, Swati, Jose, Ville)
- PSR Clean-ups, dropping support for BDW/HSD and enable PSR2 selective fetch by default (Jose, Gwan-gyeong)
- Nuke ORIGIN_GTT (Jose)
- Return proper DPRX link training result (Lee)
- FBC related refactor and fixes (Ville)
- Yet another attempt to solve the fast+narrow vs slow+wide eDP link training (Kai-Heng)
- DP 2.0 preparation work (Jani)
- Silence __iomem sparse warn (Ville)
- Clean up DPLL stuff (Ville)
- Fix various dp/edp max rates (Matt Atwood, Animesh, Jani)
- Remove VBT ddi_port_info caching (Jani)
- DSI driver improvements (Lee)
- HDCP fixes (Juston)
- Associate ACPI connector nodes with connector entries (Heikki)
- Add support for out-of-bound hotplug events (Hans)
- VESA vendor block and drm/i915 MSO use of it (Jani)
- Fixes for bigjoiner (Ville)
- Update memory bandwidth parameters (RK)
- DMC related fixes (Chris, Jose)
- HDR related fixes and improvements (Tejas)
- g4x/vlv/chv CxSR/wm fixes/cleanups (Ville)
- Use BIOS provided value for RKL Audio's HDA link (Kai-Heng)
- Fix the dsc check while selecting min_cdclk (Vandita)
- Split and constify vtable (Dave)
- Add ww context to intel_dpt_pin (Maarten)
- Fix bdb version check (Lukasz)
- DP per-lane drive settings prep work and other DP fixes (Ville)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEbSBwaO7dZQkcLOKj+mJfZA7rE8oFAmFbTsgACgkQ+mJfZA7r
E8onwQf/QLOtlY0Al7oVEQrWu7I6vzajyQz6oGbj3rTNMG6m/sDNCgKZaNmxRnQo
O+YjccMW/dnsFhSqckm8JzQUrHPSmDExBu+HGSkxNTod7UYVEEd0MYETnBShF4hv
vwoPgRuzny5+jEDuBv9GBD/6d2su9Hl/OWTQ/YPjdJKyIWLjKhbxET7FExlV6MtG
I80OyJSaV2L4EAgPT5TBSAXvzeUFAevw2O9aOSI+rTtAOfXI7TkB7E38Tjzc7uSd
YN9/43NXoJYVB9yhVXKJgK90COMSREFv/lUupSXqN/W5lOD4xLg0W6vD6kKX5Z4T
IrfvR6T5Cz+OfwSLUlzmWeO+l9VcqQ==
=9tCx
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-next-2021-10-04' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
Cross-subsystem Changes:
- fbdev/efifb: Release PCI device's runtime PM ref during FB destr\
oy (Imre)
i915 Core Driver Changes:
- Only access SFC_DONE in media when not fused off for graphics 12 and newer.
- Double Memory latency values from pcode for DG2 (Matt Roper)
- ADL-S PCI ID update (Tejas)
- New DG1 PCI ID (Jose)
- Fix regression with uncore refactoring (Dave)
i915 Display Changes:
- ADL-P display (XE_LPD) fixes and updates (Ankit, Jani, Matt Roper, Anusham, Jose, Imre, Vandita)
- DG2 display fixes (Ankit, Jani)
- Expand PCH_CNP tweaked display workaround to all newer displays (Anshuman)
- General display simplifications and clean-ups (Jani, Swati, Jose, Ville)
- PSR Clean-ups, dropping support for BDW/HSD and enable PSR2 selective fetch by default (Jose, Gwan-gyeong)
- Nuke ORIGIN_GTT (Jose)
- Return proper DPRX link training result (Lee)
- FBC related refactor and fixes (Ville)
- Yet another attempt to solve the fast+narrow vs slow+wide eDP link training (Kai-Heng)
- DP 2.0 preparation work (Jani)
- Silence __iomem sparse warn (Ville)
- Clean up DPLL stuff (Ville)
- Fix various dp/edp max rates (Matt Atwood, Animesh, Jani)
- Remove VBT ddi_port_info caching (Jani)
- DSI driver improvements (Lee)
- HDCP fixes (Juston)
- Associate ACPI connector nodes with connector entries (Heikki)
- Add support for out-of-bound hotplug events (Hans)
- VESA vendor block and drm/i915 MSO use of it (Jani)
- Fixes for bigjoiner (Ville)
- Update memory bandwidth parameters (RK)
- DMC related fixes (Chris, Jose)
- HDR related fixes and improvements (Tejas)
- g4x/vlv/chv CxSR/wm fixes/cleanups (Ville)
- Use BIOS provided value for RKL Audio's HDA link (Kai-Heng)
- Fix the dsc check while selecting min_cdclk (Vandita)
- Split and constify vtable (Dave)
- Add ww context to intel_dpt_pin (Maarten)
- Fix bdb version check (Lukasz)
- DP per-lane drive settings prep work and other DP fixes (Ville)
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Tue 05 Oct 2021 04:58:16 AEST
# gpg: using RSA key 6D207068EEDD65091C2CE2A3FA625F640EEB13CA
# gpg: Good signature from "Rodrigo Vivi <rodrigo.vivi@intel.com>" [unknown]
# gpg: aka "Rodrigo Vivi <rodrigo.vivi@gmail.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6D20 7068 EEDD 6509 1C2C E2A3 FA62 5F64 0EEB 13CA
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YVtPk6llsxBFiw7W@intel.com
In the commit bac9c29482 ("drm/edid: Break out reading block 0 of
the EDID") I broke out reading the base block of the EDID to its own
function. Unfortunately, when I did that I messed up the handling when
drm_edid_is_zero() indicated that we had an EDID that was all 0x00 or
when we went through 4 loops and didn't get a valid EDID. Specifically
I needed to pass the broken EDID to connector_bad_edid() but now I was
passing an error-pointer.
Let's re-jigger things so we can pass the bad EDID in properly.
Fixes: bac9c29482 ("drm/edid: Break out reading block 0 of the EDID")
Reported-by: kernel test robot <oliver.sang@intel.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patchwork.freedesktop.org/patch/msgid/20211004092100.1.Ic90a5ebd44c75db963112be167a03cc96f9fb249@changeid
In the patch ("drm/edid: Allow the querying/working with the panel ID
from the EDID") we introduced a different way of working with the
panel ID stored in the EDID. Let's use this new way for the quirks
code.
Advantages of the new style:
* Smaller data structure size. Saves 4 bytes per panel.
* Iterate through quirks structure with just "==" instead of strncmp()
* In-kernel storage is more similar to what's stored in the EDID
itself making it easier to grok that they are referring to the same
value.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.4.I6103ce2b16e5e5a842b14c7022a034712b434609@changeid
EDIDs have 32-bits worth of data which is intended to be used to
uniquely identify the make/model of a panel. This has historically
been used only internally in the EDID processing code to identify
quirks with panels.
We'd like to use this panel ID in panel drivers to identify which
panel is hooked up and from that information figure out power sequence
timings. Let's expose this information from the EDID code and also
allow it to be accessed early, before a connector has been created.
To make matching in the panel drivers code easier, we'll return the
panel ID as a 32-bit value. We'll provide some functions for
converting this value back and forth to something more human readable.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.3.I4a672175ba1894294d91d3dbd51da11a8239cf4a@changeid
A future change wants to be able to read just block 0 of the EDID, so
break it out of drm_do_get_edid() into a sub-function.
This is intended to be a no-op change--just code movement.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.2.I62e76a034ac78c994d40a23cd4ec5aeee56fa77c@changeid
The VESA Organization Vendor-Specific Data Block, defined in VESA
DisplayID Standard v2.0, specifies the eDP Multi-SST Operation (MSO)
stream count and segment pixel overlap.
DisplayID v1.3 has Appendix B: DisplayID as an EDID Extension,
describing how DisplayID sections may be embedded in EDID extension
blocks. DisplayID v2.0 does not have such a section, perhaps implying
that DisplayID v2.0 data should not be included in EDID extensions, but
rather in a "pure" DisplayID structure at its own DDC address pair
A4h/A5h, as described in VESA E-DDC Standard v1.3 chapter 3.
However, in practice, displays out in the field have embedded DisplayID
v2.0 data blocks in EDID extensions, including, in particular, some eDP
MSO displays, where a pure DisplayID structure is not available at all.
Parse the MSO data from the DisplayID data block. Do it as part of
drm_add_display_info(), extending it to parse also DisplayID data to
avoid requiring extra calls to update the information.
v2: Check for VESA OUI (Ville)
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/73ca2887e7b37880690f5c9ba4594c9cd1170669.1630419362.git.jani.nikula@intel.com
We'll be adding more DisplayID specific functions going forward, so
start off by splitting out a few functions to a separate file.
We don't bother with exporting the functions; at least for now they
should be needed solely within drm.ko.
No functional changes.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/07942d5011891b8e8f77245c78b34f4af97a9315.1617024940.git.jani.nikula@intel.com
We have DRM drivers based on USB, SPI and platform devices. All of them
are fine with storing their device reference in struct drm_device.dev.
PCI devices should be no exception. Therefore struct drm_device.pdev is
deprecated.
Instead upcast from struct drm_device.dev with to_pci_dev(). PCI-specific
code can use dev_is_pci() to test for a PCI device. This patch changes
the DRM core code and documentation accordingly.
v4:
* split-off pdev deprecation into separate patch
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Andy Lavr <andy.lavr@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210118131420.15874-2-tzimmermann@suse.de
Add support for DP-HDMI2.1 PCON
From the series cover letter:
This patch series attempts to add support for a DP-HDMI2.1 Protocol
Convertor. The VESA spec for the HDMI2.1 PCON are proposed in Errata
E5 to DisplayPort_v2.0:
https://vesa.org/join-vesamemberships/member-downloads/?action=stamp&fileid=42299
The details are mentioned in:
VESA DP-to-HDMI PCON Specification Standalone Document
https://groups.vesa.org/wg/DP/document/15651
This series starts with adding support for FRL (Fixed Rate Link)
Training between the PCON and HDMI2.1 sink.
As per HDMI2.1 specification, a new data-channel or lane is added in
FRL mode, by repurposing the TMDS clock Channel. Through FRL, higher
bit-rate can be supported, ie. up to 12 Gbps/lane (48 Gbps over 4
lanes).
With these patches, the HDMI2.1 PCON can be configured to achieve FRL
training based on the maximum FRL rate supported by the panel, source
and the PCON.
The approach is to add the support for FRL training between PCON and
HDMI2.1 sink and gradually add other blocks for supporting higher
resolutions and other HDMI2.1 features, that can be supported by pcon
for the sources that do not natively support HDMI2.1.
This is done before the DP Link training between the source and PCON
is started. In case of FRL training is not achieved, the PCON will
work in the regular TMDS mode, without HDMI2.1 feature support.
Any interruption in FRL training between the PCON and HDMI2.1 sink is
notified through IRQ_HPD. On receiving the IRQ_HPD the concerned DPCD
registers are read and FRL training is re-attempted.
Currently, we have tested the FRL training and are able to enable 4K
display with TGL Platform + Realtek PCON RTD2173 with HDMI2.1 supporting
panel.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87lfdpndkt.fsf@intel.com
This patch parses HFVSDB fields for DSC1.2 capabilities of an
HDMI2.1 sink. These fields are required by a source to understand the
DSC capability of the sink, to set appropriate PPS parameters,
before transmitting compressed data stream.
v2: Addressed following issues as suggested by Uma Shankar:
-Added a new struct for hdmi dsc cap
-Fixed bugs in macros usage.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
[Jani: Fixed checkpatch PARENTHESIS_ALIGNMENT.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-4-ankit.k.nautiyal@intel.com
This patch parses MAX_FRL field to get the MAX rate in Gbps that
the HDMI 2.1 panel can support in FRL mode. Source need this
field to determine the optimal rate between the source and sink
during FRL training.
v2: Fixed minor bugs, and removed extra wrapper function (Uma Shankar)
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
[Jani: Fixed checkpatch FROM_SIGN_OFF_MISMATCH, PARENTHESIS_ALIGNMENT.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-3-ankit.k.nautiyal@intel.com
Commit 991fcb77f4 ("drm/edid: Fix uninitialized variable in
drm_cvt_modes()") just replaced one warning with another.
The original warning about a possibly uninitialized variable was due to
the compiler not being smart enough to see that the case statement
actually enumerated all possible cases. And the initial fix was just to
add a "default" case that had a single "unreachable()", just to tell the
compiler that that situation cannot happen.
However, that doesn't actually fix the fundamental reason for the
problem: the compiler still doesn't see that the existing case
statements enumerate all possibilities, so the compiler will still
generate code to jump to that unreachable case statement. It just won't
complain about an uninitialized variable any more.
So now the compiler generates code to our inline asm marker that we told
it would not fall through, and end end result is basically random. We
have created a bridge to nowhere.
And then, depending on the random details of just exactly what the
compiler ends up doing, 'objtool' might end up complaining about the
conditional branches (for conditions that cannot happen, and that thus
will never be taken - but if the compiler was not smart enough to figure
that out, we can't expect objtool to do so) going off in the weeds.
So depending on how the compiler has laid out the result, you might see
something like this:
drivers/gpu/drm/drm_edid.o: warning: objtool: do_cvt_mode() falls through to next function drm_mode_detailed.isra.0()
and now you have a truly inscrutable warning that makes no sense at all
unless you start looking at whatever random code the compiler happened
to generate for our bare "unreachable()" statement.
IOW, don't use "unreachable()" unless you have an _active_ operation
that generates code that actually makes it obvious that something is not
reachable (ie an UD instruction or similar).
Solve the "compiler isn't smart enough" problem by just marking one of
the cases as "default", so that even when the compiler doesn't otherwise
see that we've enumerated all cases, the compiler will feel happy and
safe about there always being a valid case that initializes the 'width'
variable.
This also generates better code, since now the compiler doesn't generate
comparisons for five different possibilities (the four real ones and the
one that can't happen), but just for the three real ones and "the rest"
(which is that last one).
A smart enough compiler that sees that we cover all the cases won't care.
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Noticed this when trying to compile with -Wall on a kernel fork. We
potentially don't set width here, which causes the compiler to complain
about width potentially being uninitialized in drm_cvt_modes(). So, let's
fix that.
Changes since v1:
* Don't emit an error as this code isn't reachable, just mark it as such
Changes since v2:
* Remove now unused variable
Fixes: 3f649ab728 ("treewide: Remove uninitialized_var() usage")
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ilia Mirkin <imirkin@alum.mit.edu>
Link: https://patchwork.freedesktop.org/patch/msgid/20201105235703.1328115-1-lyude@redhat.com
We have a few displays in CI that always report their EDID as a bunch of
zeroes. This is consistent behaviour, so one assumes intentional
indication of an "absent" EDID. Flagging these consistent warnings
detracts from CI.
One option would be to ignore the zero EDIDs as intentional behaviour,
but Ville would like to keep the information available for debugging.
The simple alternative then is to reduce the loglevel for all the EDID
dumping from WARN to DEBUG so the information is present but not annoy
CI. Note that the bad EDID dumping is already only shown if
drm.debug=KMS, it's just the loglevel chosen was set to be caught by CI
if it ever occurred as it was expected to be an internal error not
external.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2203
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201029213042.11672-1-chris@chris-wilson.co.uk
The name of the argument is different, causing those warnings:
./drivers/gpu/drm/drm_edid.c:3754: warning: Function parameter or member 'video_code' not described in 'drm_display_mode_from_cea_vic'
./drivers/gpu/drm/drm_edid.c:3754: warning: Excess function parameter 'vic' description in 'drm_display_mode_from_cea_vic'
Fixes: 7af655bce2 ("drm/dp: Add drm_dp_downstream_mode()")
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/7f4d6c3ff6df63ebd006eb90a5108006c23e2168.1603791716.git.mchehab+huawei@kernel.org
The name of the argument is different, causing those warnings:
./drivers/gpu/drm/drm_edid.c:3754: warning: Function parameter or member 'video_code' not described in 'drm_display_mode_from_cea_vic'
./drivers/gpu/drm/drm_edid.c:3754: warning: Excess function parameter 'vic' description in 'drm_display_mode_from_cea_vic'
Fixes: 7af655bce2 ("drm/dp: Add drm_dp_downstream_mode()")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200922175357.42998-3-lyude@redhat.com
The downstream facing port caps in the DPCD can give us a hint
as to what kind of display mode the sink can use if it doesn't
have an EDID. Use that information to pick a suitable mode.
v2: Use Returns: for kdoc (Lyude)
Add kdocs for drm_display_mode_from_cea_vic() (Lyude)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-14-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
