Introduce ->get_input_bus_fmts() callback to struct dw_mipi_dsi_plat_data
so that vendor drivers can implement specific methods to get input bus
formats for Synopsys DW MIPI DSI.
While at it, implement a generic callback for ->atomic_get_input_bus_fmts(),
where we try to get the input bus formats through pdata->get_input_bus_fmts()
first. If it's unavailable, fall back to the only format - MEDIA_BUS_FMT_FIXED,
which matches the default behavior if ->atomic_get_input_bus_fmts() is not
implemented as ->atomic_get_input_bus_fmts()'s kerneldoc indicates.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-3-victor.liu@nxp.com
Add dw_mipi_dsi_get_bridge() helper so that it can be used by vendor
drivers which implement vendor specific extensions to Synopsys DW MIPI DSI.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-2-victor.liu@nxp.com
Having conditional around the of_node pointers turns out to make driver
code use ugly #ifdef and #if blocks. So drop the conditionals.
Suggested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230831080938.47454-4-biju.das.jz@bp.renesas.com
The ELD (EDID-Like Data) is not updated when the HDMI cable
is plugged into different HDMI monitors.
This is because the EDID is not updated in the HDMI HPD function.
As a result, the ELD data remains unchanged and may not reflect
the capabilities of the newly connected HDMI sink device.
To address this issue, the handle_plugged_change function should move to
the bridge_atomic_enable and bridge_atomic_disable functions.
Make sure the EDID is properly updated before updating ELD.
Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230804061145.2824843-1-Sandor.yu@nxp.com
CEC interrupt status/mask and logical address registers
will be reset when device enter suspend.
It will cause cec fail to work after device resume.
Add CEC suspend/resume functions, reinitialize logical address registers
and restore interrupt status/mask registers after resume.
Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230721124415.1513223-1-Sandor.yu@nxp.com
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714174545.4056287-1-robh@kernel.org
UAPI Changes:
* fbdev:
* Make fbdev userspace interfaces optional; only leaves the
framebuffer console active
* prime:
* Support dma-buf self-import for all drivers automatically: improves
support for many userspace compositors
Cross-subsystem Changes:
* backlight:
* Fix interaction with fbdev in several drivers
* base: Convert struct platform.remove to return void; part of a larger,
tree-wide effort
* dma-buf: Acquire reservation lock for mmap() in exporters; part
of an on-going effort to simplify locking around dma-bufs
* fbdev:
* Use Linux device instead of fbdev device in many places
* Use deferred-I/O helper macros in various drivers
* i2c: Convert struct i2c from .probe_new to .probe; part of a larger,
tree-wide effort
* video:
* Avoid including <linux/screen_info.h>
Core Changes:
* atomic:
* Improve logging
* prime:
* Remove struct drm_driver.gem_prime_mmap plus driver updates: all
drivers now implement this callback with drm_gem_prime_mmap()
* gem:
* Support execution contexts: provides locking over multiple GEM
objects
* ttm:
* Support init_on_free
* Swapout fixes
Driver Changes:
* accel:
* ivpu: MMU updates; Support debugfs
* ast:
* Improve device-model detection
* Cleanups
* bridge:
* dw-hdmi: Improve support for YUV420 bus format
* dw-mipi-dsi: Fix enable/disable of DSI controller
* lt9611uxc: Use MODULE_FIRMWARE()
* ps8640: Remove broken EDID code
* samsung-dsim: Fix command transfer
* tc358764: Handle HS/VS polarity; Use BIT() macro; Various cleanups
* Cleanups
* ingenic:
* Kconfig REGMAP fixes
* loongson:
* Support display controller
* mgag200:
* Minor fixes
* mxsfb:
* Support disabling overlay planes
* nouveau:
* Improve VRAM detection
* Various fixes and cleanups
* panel:
* panel-edp: Support AUO B116XAB01.4
* Support Visionox R66451 plus DT bindings
* Cleanups
* ssd130x:
* Support per-controller default resolution plus DT bindings
* Reduce memory-allocation overhead
* Cleanups
* tidss:
* Support TI AM625 plus DT bindings
* Implement new connector model plus driver updates
* vkms
* Improve write-back support
* Documentation fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAmSvvRAACgkQaA3BHVML
eiNpGQgAs8jq1XjN9t8jZsdgXnoCbkZyVUI2NO0HwoVwpRCLgbXp5AX5qq2oRciE
TBhe4Fceh/ZsYqHTZQahnguxgRKM5JgXwbI4Z0iiOVcqasNbycaKAqipxJJ7kdo1
qPhGCbgQFVX7oIq2xjfXehh6O0SYX+R9r88X8dMJxMYv/pcLwOHG74kS040WOcQq
uATgcnobOf/D8ZmlqvfKGAeTUoFo/RSR2Uhlauka58qgeUbicrTELZT2barY9d+k
as6U5vv4wx2zMklTkjrlkMpAT1ZpbB9d3jGHwL27VEnjlfd3wV2bdH7Dzn9qZRf/
gn0ALg/b3u5yBWk/k7YBvijXyNcH6Q==
=bBuG
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2023-07-13' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v6.6:
UAPI Changes:
* fbdev:
* Make fbdev userspace interfaces optional; only leaves the
framebuffer console active
* prime:
* Support dma-buf self-import for all drivers automatically: improves
support for many userspace compositors
Cross-subsystem Changes:
* backlight:
* Fix interaction with fbdev in several drivers
* base: Convert struct platform.remove to return void; part of a larger,
tree-wide effort
* dma-buf: Acquire reservation lock for mmap() in exporters; part
of an on-going effort to simplify locking around dma-bufs
* fbdev:
* Use Linux device instead of fbdev device in many places
* Use deferred-I/O helper macros in various drivers
* i2c: Convert struct i2c from .probe_new to .probe; part of a larger,
tree-wide effort
* video:
* Avoid including <linux/screen_info.h>
Core Changes:
* atomic:
* Improve logging
* prime:
* Remove struct drm_driver.gem_prime_mmap plus driver updates: all
drivers now implement this callback with drm_gem_prime_mmap()
* gem:
* Support execution contexts: provides locking over multiple GEM
objects
* ttm:
* Support init_on_free
* Swapout fixes
Driver Changes:
* accel:
* ivpu: MMU updates; Support debugfs
* ast:
* Improve device-model detection
* Cleanups
* bridge:
* dw-hdmi: Improve support for YUV420 bus format
* dw-mipi-dsi: Fix enable/disable of DSI controller
* lt9611uxc: Use MODULE_FIRMWARE()
* ps8640: Remove broken EDID code
* samsung-dsim: Fix command transfer
* tc358764: Handle HS/VS polarity; Use BIT() macro; Various cleanups
* Cleanups
* ingenic:
* Kconfig REGMAP fixes
* loongson:
* Support display controller
* mgag200:
* Minor fixes
* mxsfb:
* Support disabling overlay planes
* nouveau:
* Improve VRAM detection
* Various fixes and cleanups
* panel:
* panel-edp: Support AUO B116XAB01.4
* Support Visionox R66451 plus DT bindings
* Cleanups
* ssd130x:
* Support per-controller default resolution plus DT bindings
* Reduce memory-allocation overhead
* Cleanups
* tidss:
* Support TI AM625 plus DT bindings
* Implement new connector model plus driver updates
* vkms
* Improve write-back support
* Documentation fixes
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230713090830.GA23281@linux-uq9g
Right now clocking value selection code is prioritising RGB, YUV444 modes
over YUV420 for HDMI2 sinks. However, because of the bus format selection
procedure in dw-hdmi, for HDMI2 sinks YUV420 is the format that will always
be picked during the drm bridge chain check stage.
Later on dw_hdmi_setup will configure a colour space based on the bus
format that doesn't match the pixel value we had calculated as described
above.
Fix it by bringing back dw-hdmi bus format check when picking the right
pixel clock.
Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/6230bfae2cd97cf6527fc62ba5c850464919ccf8.1687702042.git.adrian.larumbe@collabora.com
Commit 5d844091f2 ("drm/scdc-helper: Pimp SCDC debugs") changed the scdc
interface to pick up an i2c adapter from a connector instead. However, in
the case of dw-hdmi, the wrong connector was being used to pass i2c adapter
information, since dw-hdmi's embedded connector structure is only populated
when the bridge attachment callback explicitly asks for it.
drm-meson is handling connector creation, so this won't happen, leading to
a NULL pointer dereference.
Fix it by having scdc functions access dw-hdmi's current connector pointer
instead, which is assigned during the bridge enablement stage.
Fixes: 5d844091f2 ("drm/scdc-helper: Pimp SCDC debugs")
Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Reported-by: Lukas F. Hartmann <lukas@mntre.com>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
[narmstrong: moved Fixes tag before first S-o-b and added Reported-by tag]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230601123153.196867-1-adrian.larumbe@collabora.com
Before this patch, booting to Linux VT and doing a simple:
echo 2 > /sys/class/graphics/fb0/blank
echo 0 > /sys/class/graphics/fb0/blank
would result in failures to re-enable the panel. Mode set callback is
called only once during boot in this scenario, while calls to
enable/disable callbacks are balanced afterwards. The driver doesn't
work unless userspace calls modeset before enabling the CRTC/connector.
This patch moves enabling of the DSI host from mode_set into pre_enable
callback, and removes some old hacks where this bridge driver is
directly calling into other bridge driver's callbacks.
pre_enable_prev_first flag is set on the panel's bridge so that panel
drivers will get their prepare function called between DSI host's
pre_enable and enable callbacks, so that they get a chance to
perform panel setup while DSI host is already enabled in command
mode. Otherwise panel's prepare would be called before DSI host
is enabled, and any DSI communication used in prepare callback
would fail.
With all these changes, the enable/disable sequence is now well
balanced, and host's and panel's callbacks are called in proper order
documented in the drm_panel API documentation without needing the old
hacks. (Mainly that panel->prepare is called when DSI host is ready to
allow the panel driver to send DSI commands and vice versa during
disable.)
Tested on Pinephone Pro. Trace of the callbacks follows.
Before:
[ 1.253882] dw-mipi-dsi-rockchip ff960000.dsi: mode_set
[ 1.290732] panel-himax-hx8394 ff960000.dsi.0: prepare
[ 1.475576] dw-mipi-dsi-rockchip ff960000.dsi: enable
[ 1.475593] panel-himax-hx8394 ff960000.dsi.0: enable
echo 2 > /sys/class/graphics/fb0/blank
[ 13.722799] panel-himax-hx8394 ff960000.dsi.0: disable
[ 13.774502] dw-mipi-dsi-rockchip ff960000.dsi: post_disable
[ 13.774526] panel-himax-hx8394 ff960000.dsi.0: unprepare
echo 0 > /sys/class/graphics/fb0/blank
[ 17.735796] panel-himax-hx8394 ff960000.dsi.0: prepare
[ 17.923522] dw-mipi-dsi-rockchip ff960000.dsi: enable
[ 17.923540] panel-himax-hx8394 ff960000.dsi.0: enable
[ 17.944330] dw-mipi-dsi-rockchip ff960000.dsi: failed to write command FIFO
[ 17.944335] panel-himax-hx8394 ff960000.dsi.0: sending command 0xb9 failed: -110
[ 17.944340] panel-himax-hx8394 ff960000.dsi.0: Panel init sequence failed: -110
echo 2 > /sys/class/graphics/fb0/blank
[ 431.148583] panel-himax-hx8394 ff960000.dsi.0: disable
[ 431.169259] dw-mipi-dsi-rockchip ff960000.dsi: failed to write command FIFO
[ 431.169268] panel-himax-hx8394 ff960000.dsi.0: Failed to enter sleep mode: -110
[ 431.169282] dw-mipi-dsi-rockchip ff960000.dsi: post_disable
[ 431.169316] panel-himax-hx8394 ff960000.dsi.0: unprepare
[ 431.169357] pclk_mipi_dsi0 already disabled
echo 0 > /sys/class/graphics/fb0/blank
[ 432.796851] panel-himax-hx8394 ff960000.dsi.0: prepare
[ 432.981537] dw-mipi-dsi-rockchip ff960000.dsi: enable
[ 432.981568] panel-himax-hx8394 ff960000.dsi.0: enable
[ 433.002290] dw-mipi-dsi-rockchip ff960000.dsi: failed to write command FIFO
[ 433.002299] panel-himax-hx8394 ff960000.dsi.0: sending command 0xb9 failed: -110
[ 433.002312] panel-himax-hx8394 ff960000.dsi.0: Panel init sequence failed: -110
-----------------------------------------------------------------------
After:
[ 1.248372] dw-mipi-dsi-rockchip ff960000.dsi: mode_set
[ 1.248704] dw-mipi-dsi-rockchip ff960000.dsi: pre_enable
[ 1.285377] panel-himax-hx8394 ff960000.dsi.0: prepare
[ 1.468392] dw-mipi-dsi-rockchip ff960000.dsi: enable
[ 1.468421] panel-himax-hx8394 ff960000.dsi.0: enable
echo 2 > /sys/class/graphics/fb0/blank
[ 16.210357] panel-himax-hx8394 ff960000.dsi.0: disable
[ 16.261315] dw-mipi-dsi-rockchip ff960000.dsi: post_disable
[ 16.261339] panel-himax-hx8394 ff960000.dsi.0: unprepare
echo 0 > /sys/class/graphics/fb0/blank
[ 19.161453] dw-mipi-dsi-rockchip ff960000.dsi: pre_enable
[ 19.197869] panel-himax-hx8394 ff960000.dsi.0: prepare
[ 19.382141] dw-mipi-dsi-rockchip ff960000.dsi: enable
[ 19.382158] panel-himax-hx8394 ff960000.dsi.0: enable
(But depends on functionality intorduced in Linux 6.3, so this patch will
not build on older kernels when applied to older stable branches.)
Fixes: 46fc51546d ("drm/bridge/synopsys: Add MIPI DSI host controller bridge")
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230617224915.1923630-1-megi@xff.cz
Include the device and connector information in the SCDC
debugs. Makes it easier to figure out who did what.
v2: Rely on connector->ddc (Maxime)
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Robert Foss <rfoss@kernel.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Emma Anholt <emma@anholt.net>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230403223652.18848-1-ville.syrjala@linux.intel.com
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318190804.234610-18-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318190804.234610-17-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318190804.234610-16-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318190804.234610-15-u.kleine-koenig@pengutronix.de
commit f77a066f4e ("ASoC: hdmi-codec: Allow playback and capture
to be disabled") added new no_i2s_playback/capture.
We need to zero clear HDMI pdata first, otherwise unexpected flag
will be added.
Fixes: f77a066f4e ("ASoC: hdmi-codec: Allow playback and capture to be disabled")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87k01hlnqj.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cheap monitors sometimes advertise YUV modes they don't really have
(HDMI specification mandates YUV support so even monitors without actual
support will often wrongfully advertise it) which results in YUV matches
and user forum complaints of a red tint to light colour display areas in
common desktop environments.
Moving the default RGB fall-back before YUV selection results in RGB
mode matching in most cases, reducing complaints.
Fixes: 6c3c719936 ("drm/bridge: synopsys: dw-hdmi: add bus format negociation")
Signed-off-by: Guillaume BRUN <the.cheaterman@gmail.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221116143523.2126-1-the.cheaterman@gmail.com
The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL terminated strings.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220919030401.211331-1-chi.minghao@zte.com.cn
drm-misc-next for v6.1-rc1:
[airlied - fix sun4i_tv build]
UAPI Changes:
- Hide unregistered connectors from GETCONNECTOR ioctl.
- drm/virtio no longer advertises LINEAR modifier, as it doesn't work.
-
Cross-subsystem Changes:
- Fix GPF in udmabuf failure path.
Core Changes:
- Rework TTM placement to use intersect/compatible functions.
- Drop legacy DP-MST support.
- More DP-MST related fixes, and move all state into atomic.
- Make DRM_MIPI_DBI select DRM_KMS_HELPER.
- Add audio_infoframe packing for DP.
- Add logging when some atomic check functions fail.
- Assorted documentation updates and fixes.
Driver Changes:
- Assorted cleanups and fixes in msm, lcdif, nouveau, virtio,
panel/ilitek, bridge/icn6211, tve200, gma500, bridge/*, panfrost, via,
bochs, qxl, sun4i.
- Add add AUO B133UAN02.1, IVO M133NW4J-R3, Innolux N120ACA-EA1 eDP panels.
- Improve DP-MST modeset state handling in amdgpu, nouveau, i915.
- Drop DP-MST from radeon driver, it was broken and only user of legacy
DP-MST.
- Handle unplugging better in vc4.
- Simplify drm cmdparser tests.
- Add DP support to ti-sn65dsi86.
- Add MT8195 DP support to mediatek.
- Support RGB565, XRGB64, and ARGB64 formats in vkms.
- Convert sun4i tv support to atomic.
- Refactor vc4/vec TV Modesetting, and fix timings.
- Use atomic helpers instead of simple display helpers in ssd130x.
Maintainer changes:
- Add Douglas Anderson as reviewer for panel-edp.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a489485b-3ebc-c734-0f80-aed963d89efe@linux.intel.com
There are two events that signal a real change of the link state: HPD going
high means the sink is newly connected or wants the source to re-read the
EDID, RX sense going low is a indication that the link has been disconnected.
Ignore the other two events that also trigger interrupts, but don't need
immediate attention: HPD going low does not necessarily mean the link has
been lost and should not trigger a immediate read of the status. RX sense
going high also does not require a detect cycle, as HPD going high is the
right point in time to read the EDID.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> (v1)
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220826185733.3213248-1-l.stach@pengutronix.de
As diffstat shows, we've had lots of developments in a wide range
at this time; the majority of changes are about ASoC, including
subsystem-wide cleanups, continued SOF / Intel updates and a
bunch of new drivers (as usual), while there have been some
significant (but almost invisible) improvements in ALSA core
side, too. Below are some highlights:
Core:
- Faster lookups of control elements with Xarray; normal user
won't notice, but on the devices with tons of control elements,
it can be visibly faster
- Support for input validation for controls; this will harden
for badly written drivers in general with a slight overhead
- Deferred async signal handling for working around the potential
deadlocks
- Cleanup / refactoring raw MIDI locking code
ASoC:
- Restructing of the set_fmt() callbacks for making things clearer
in situations like CODEC to CODEC links
- Clean up and modernizing the DAI naming scheme setups
- Merge of more of the Intel AVS driver stack, including some
board integrations
- New version 4 mechanism for communication with SOF DSPs
- Suppoort for dynamically selecting the PLL to use at runtime on
i.MX platforms
- Improvements for CODEC to CODEC support in the generic cards
- Support for AMD Jadeite and various machines, AMD RPL, Intel
MetorLake DSPs, Mediatek MT8186 DSPs and MT6366, nVidia Tegra
MDDRC, OPE and PEQ, NXP TFA9890, Qualcomm SDM845, WCD9335 and
WAS883x, and Texas Instruments TAS2780
HD- and USB-audio:
- Continued improvement for CS35L41 (sub)codec support
- More quirks for various devices (HP, Lenovo, Dell, Clevo)
-----BEGIN PGP SIGNATURE-----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=1n0/
-----END PGP SIGNATURE-----
Merge tag 'sound-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"As the diffstat shows, we've had lots of developments in a wide range
at this time; the majority of changes are about ASoC, including
subsystem-wide cleanups, continued SOF / Intel updates and a bunch of
new drivers (as usual), while there have been some significant (but
almost invisible) improvements in ALSA core side, too.
Below are some highlights:
Core:
- Faster lookups of control elements with Xarray; normal user won't
notice, but on the devices with tons of control elements, it can be
visibly faster
- Support for input validation for controls; this will harden for
badly written drivers in general with a slight overhead
- Deferred async signal handling for working around the potential
deadlocks
- Cleanup / refactoring raw MIDI locking code
ASoC:
- Restructing of the set_fmt() callbacks for making things clearer in
situations like CODEC to CODEC links
- Clean up and modernizing the DAI naming scheme setups
- Merge of more of the Intel AVS driver stack, including some board
integrations
- New version 4 mechanism for communication with SOF DSPs
- Suppoort for dynamically selecting the PLL to use at runtime on
i.MX platforms
- Improvements for CODEC to CODEC support in the generic cards
- Support for AMD Jadeite and various machines, AMD RPL, Intel
MetorLake DSPs, Mediatek MT8186 DSPs and MT6366, nVidia Tegra
MDDRC, OPE and PEQ, NXP TFA9890, Qualcomm SDM845, WCD9335 and
WAS883x, and Texas Instruments TAS2780
HD- and USB-audio:
- Continued improvement for CS35L41 (sub)codec support
- More quirks for various devices (HP, Lenovo, Dell, Clevo)"
* tag 'sound-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (778 commits)
ALSA: hda/realtek: Add quirk for HP Spectre x360 15-eb0xxx
ALSA: line6: Replace sprintf() with sysfs_emit()
ALSA: hda: Replace sprintf() with sysfs_emit()
ALSA: pcm: Replace sprintf() with sysfs_emit()
ALSA: core: Replace scnprintf() with sysfs_emit()
ALSA: control-led: Replace sprintf() with sysfs_emit()
ALSA: aoa: Replace sprintf() with sysfs_emit()
ALSA: ac97: Replace sprintf() with sysfs_emit()
ALSA: hda/realtek: Add quirk for Clevo NV45PZ
ALSA: hda/realtek: Add quirk for Lenovo Yoga9 14IAP7
ALSA: control: Use deferred fasync helper
ALSA: pcm: Use deferred fasync helper
ALSA: timer: Use deferred fasync helper
ALSA: core: Add async signal helpers
ASoC: q6asm: use kcalloc() instead of kzalloc()
ACPI: scan: Add CLSA0101 Laptop Support
ALSA: hda: cs35l41: Support CLSA0101
ALSA: hda: cs35l41: Use the CS35L41 HDA internal define
ASoC: dt-bindings: use spi-peripheral-props.yaml
ASoC: codecs: va-macro: use fsgen as clock
...
drm_crtc.h has no need for linux/i2c.h, so don't include it.
Avoids useless rebuilds of the entire universe when
touching linux/i2c.h.
Quite a few placs do currently depend on linux/i2c.h without
actually including it directly. All of those need to be
fixed up.
v2: imx and mcde need linux/io.h for readl()/etc.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220630195114.17407-5-ville.syrjala@linux.intel.com
As part of retiring the old defines used to specify DAI formats update the
hdmi_codec driver to use the modern names, including the variables in the
struct hdmi_codec_daifmt exported to the DRM drivers.
In updating this I did note that the only use of this information in DRM
drivers is to reject clock provider settings, thinking about what this
hardware is doing I rather suspect that there might not be any hardware
out there which needs the configuration so it may be worth considering
just having hdmi-codec support only clock consumer.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220602103029.3498791-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
SCDC is the Status and Control Data Channel for HDMI. Move the SCDC
helpers into display/ and split the header into files for core and
helpers. Update all affected drivers. No functional changes.
To avoid the proliferation of Kconfig options, SCDC is part of DRM's
support for HDMI. If necessary, a new option could make SCDC an
independent feature.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-9-tzimmermann@suse.de
Move DRM's HMDI helpers into the display/ subdirectoy and add it
to DRM's display helpers. Update all affected drivers. No functional
changes.
The HDMI helpers were implemented in the EDID and connector code, but
are actually unrelated. With the move to the display-helper library, we
can remove the dependency on drm_edid.{c,h} in some driver's HDMI source
files.
Several of the HDMI helpers remain in EDID code because both share parts
of their implementation internally. With better refractoring of the EDID
code, those HDMI helpers could be moved into the display-helper library
as well.
v3:
* fix Kconfig dependencies (Javier)
v2:
* reduce HDMI helpers to avoid exporting functions (Jani)
* fix include statements (Jani, Javier)
* update Kconfig symbols
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-8-tzimmermann@suse.de
General Parallel Audio (GPA) interface is one of the supported
audio interface for synopsys HDMI module, which has verified for
i.MX8MPlus platform.
This is initial version for GPA.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/f21ba3e8c4d9d028ac74c6f3c588ddbffe739399.1649989179.git.Sandor.yu@nxp.com
PHY reset register(MC_PHYRSTZ) active high reset control for PHY GEN2,
and active low reset control for PHY GEN1.
Rename function dw_hdmi_phy_reset to dw_hdmi_phy_gen2_reset.
Add dw_hdmi_phy_gen1_reset function for PHY GEN1.
Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/e0b3be2d63fe3e95246fb8b8b0dcd57415b29e04.1649989179.git.Sandor.yu@nxp.com
HDMI1.4b specification section 6.5.3:
Source shall only send GCPs with non-zero CD to sinks
that indicate support for Deep Color.
DW HDMI GCP default enabled, but only transmit CD
and do not handle AVMUTE, PP norDefault_Phase (yet).
Disable Auto GCP when 24-bit color for sinks that not support Deep Color.
Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/78fa41e4fb3d3d53354034bc221fcf870dbac617.1649989179.git.Sandor.yu@nxp.com
i.MX8MPlus (v2.13a) has verified need the workaround to clear the
overflow with one iteration.
Only i.MX6Q(v1.30a) need the workaround with 4 iterations,
the others versions later than v1.3a have been identified as needing
the workaround with a single iteration.
Default enable the workaround with one iteration for all versions
later than v1.30a.
Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/561951005a85574dcdd108e5d6a3a87df930ea3d.1649989179.git.Sandor.yu@nxp.com
devm_drm_of_get_bridge is capable of looking up the downstream
bridge and panel and trying to add a panel bridge if the panel
is found.
Replace explicit finding calls with devm_drm_of_get_bridge.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331154503.66054-4-jagan@amarulasolutions.com
This reverts commit c206c7faeb.
In order to avoid any probe ordering issues, the I2C based downstream
bridge drivers now register and attach the DSI devices at the probe
instead of doing it on drm_bridge_function.attach().
Examples of those commits are:
commit <6ef7ee48765f> ("drm/bridge: sn65dsi83: Register and attach our
DSI device at probe")
commit <d89078c37b10> ("drm/bridge: lt8912b: Register and attach our DSI
device at probe")
commit <864c49a31d6b> ("drm/bridge: adv7511: Register and attach our DSI
device at probe")
dw-mipi-dsi has panel or bridge finding code based on previous downstream
bridges, so revert the same and make the panel or bridge funding in host
attach as before.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331154503.66054-1-jagan@amarulasolutions.com
struct drm_display_mode embeds a list head, so overwriting
the full struct with another one will corrupt the list
(if the destination mode is on a list). Use drm_mode_copy()
instead which explicitly preserves the list head of
the destination mode.
Even if we know the destination mode is not on any list
using drm_mode_copy() seems decent as it sets a good
example. Bad examples of not using it might eventually
get copied into code where preserving the list head
actually matters.
Obviously one case not covered here is when the mode
itself is embedded in a larger structure and the whole
structure is copied. But if we are careful when copying
into modes embedded in structures I think we can be a
little more reassured that bogus list heads haven't been
propagated in.
@is_mode_copy@
@@
drm_mode_copy(...)
{
...
}
@depends on !is_mode_copy@
struct drm_display_mode *mode;
expression E, S;
@@
(
- *mode = E
+ drm_mode_copy(mode, &E)
|
- memcpy(mode, E, S)
+ drm_mode_copy(mode, E)
)
@depends on !is_mode_copy@
struct drm_display_mode mode;
expression E;
@@
(
- mode = E
+ drm_mode_copy(&mode, &E)
|
- memcpy(&mode, E, S)
+ drm_mode_copy(&mode, E)
)
@@
struct drm_display_mode *mode;
@@
- &*mode
+ mode
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218100403.7028-7-ville.syrjala@linux.intel.com
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
When the dw-hdmi bridge is in first place of the bridge chain, this
means there is no way to select an input format of the dw-hdmi HW
component.
Since introduction of display-connector, negotiation was broken since
the dw-hdmi negotiation code only worked when the dw-hdmi bridge was
in last position of the bridge chain or behind another bridge also
supporting input & output format negotiation.
Commit 7cd70656d1 ("drm/bridge: display-connector: implement bus fmts callbacks")
was introduced to make negotiation work again by making display-connector
act as a pass-through concerning input & output format negotiation.
But in the case where the dw-hdmi is single in the bridge chain, for
example on Renesas SoCs, with the display-connector bridge the dw-hdmi
is no more single, breaking output format.
Reported-by: Biju Das <biju.das.jz@bp.renesas.com>
Bisected-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Fixes: 6c3c719936 ("drm/bridge: synopsys: dw-hdmi: add bus format negociation")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: add proper fixes commit]
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204143337.89221-1-narmstrong@baylibre.com
Replace atomic version of the enable/disable operations to
continue the transition to the atomic API.
Also added default drm atomic operations for duplicate, destroy
and reset state API's in order to have smooth transition on
atomic API's.
Tested on Engicam i.Core STM32MP1 SoM.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211112061741.120898-1-jagan@amarulasolutions.com
Reviewed-by: Robert Foss <robert.foss@linaro.org>
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable().
Add missing pm_runtime_disable() for __dw_mipi_dsi_probe.
Fixes: 46fc51546d ("drm/bridge/synopsys: Add MIPI DSI host controller bridge")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220105104113.31415-1-linmq006@gmail.com
Reviewed-by: Robert Foss <robert.foss@linaro.org>
To evaluate the validity of a video mode, some additional internal
value has to be passed to the platform implementation.
Extend the prototype of mode_valid().
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@foss.st.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211218215055.212421-2-antonio.borneo@foss.st.com
The current ELD handling takes the internal connector ELD buffer and
shares it to the I2S and AHB sub-driver.
But with DRM_BRIDGE_ATTACH_NO_CONNECTOR, the connector is created
elsewhere (or not), and an eventual connector is known only
if the bridge chain up to a connector is enabled.
The current dw-hdmi code gets the current connector from
atomic_enable() so use the already stored connector pointer and
replace the buffer pointer with a callback returning the current
connector ELD buffer.
Since a connector is not always available, either pass an empty
ELD to the alsa HDMI driver or don't call snd_pcm_hw_constraint_eld()
in AHB driver.
Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: fixed typo in commit log]
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211029135947.3022875-1-narmstrong@baylibre.com
The helper function devm_add_action_or_reset() will internally
call devm_add_action(), and if devm_add_action() fails then it will
execute the action mentioned and return the error code. So
use devm_add_action_or_reset() instead of devm_add_action()
to simplify the error handling, reduce the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922125909.215-1-caihuoqing@baidu.com
UAPI Changes:
- Add modifiers for arm fixed rate compression.
Cross-subsystem Changes:
- Assorted dt binding fixes.
- Convert ssd1307fb to json-schema.
- Update a lot of irc channels to point to OFTC, as everyone moved there.
- Fix the same divide by zero for asilantfb, kyro, rivafb.
Core Changes:
- Document requirements for new atomic properties.
- Add drm_gem_fb_(begin/end)_cpu_access helpers, and use them in some drivers.
- Document drm_property_enum.value for bitfields.
- Add explicit _NO_ for MIPI_DSI flags that disable features.
- Assorted documentation fixes.
- Update fb_damage handling, and move drm_plane_enable_fb_damage_clips to core.
- Add logging and docs to RMFB ioctl.
- Assorted small fixes to dp_mst, master handling.
- Clarify drm lease usage.
Driver Changes:
- Assorted small fixes to panfrost, hibmc, bridge/nwl-dsi, rockchip, vc4.
- More drm -> linux irq conversions.
- Add support for some Logic Technologies and Multi-Inno panels.
- Expose phy-functionality for drm/rockchip, to allow controlling from the media subsystem.
- Add support for 2 AUO panels.
- Add damage handling to ssd1307fb.
- Improve FIFO handling on mxsfb.
- Assorted small fixes to vmwgfx, and bump version to 2.19 for the new ioctls.
- Improve sony acx424akp backlight handling.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEuXvWqAysSYEJGuVH/lWMcqZwE8MFAmEDFiUACgkQ/lWMcqZw
E8NSbA//aw/TgTpwGNnJNHDJPwXS8WSC+1ouUJ6IKmFUkxZhpK++bJYaCZ5cj//I
pf9078qC4hXXmCCzTtQ3JawLhaZ2G33qfKod0JiB+4jrdQ4W5vYaZ3uFxiws0iu9
6KoPL1k8wO8L8CntXi3akSM/KFFrYQzjtt0MDZspIxVdd2AKBFAdwdLDqVvk1Ix6
xBpnpC7uXBVev4kTL8W7SN7HxnKHaPTwE4pUUNrR56rvjYIRd9rgdsJKNaR9oTeO
I6ARYRKSjeVsguVV6Eqy2hEBOG2v0Zy/T54z/2ksjw64A6uerenv92nwO34FXthx
59tuBYYsfKlEsKTQVHCys2+8RwcFVZIk+k1tr1h7LM7My6ynFVIOMDV+Upuv77+p
q2YiM0r6c3TgmZiqAuTdkvs8dbTgSb2j7Enq04ee3QnXnNek9hvdCyIsLQvkqrGT
m9I6F/2Rl9X2IFbVv+ia4hLk0IlBPAgZrNMP363AodQAjq54ED8baO26qKY9Y+aG
AIS4DEJ0odNE/G+MKhz84Lpdyq+kOK4tgaORBOQTeDlZLzHyxrYgl8wV+E/RNTKN
YU5cLOJaVedd/onHgq51XVio5djWCRfwCHM9HKAgDONcW8LvHXFidvscg2Mw4f1g
1rfnSOJyV8CARjjiigjBfnxweWvEK6J13lt8tl0z7OYpuVOQkxU=
=ZSMl
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2021-07-29' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.15:
UAPI Changes:
- Add modifiers for arm fixed rate compression.
Cross-subsystem Changes:
- Assorted dt binding fixes.
- Convert ssd1307fb to json-schema.
- Update a lot of irc channels to point to OFTC, as everyone moved there.
- Fix the same divide by zero for asilantfb, kyro, rivafb.
Core Changes:
- Document requirements for new atomic properties.
- Add drm_gem_fb_(begin/end)_cpu_access helpers, and use them in some drivers.
- Document drm_property_enum.value for bitfields.
- Add explicit _NO_ for MIPI_DSI flags that disable features.
- Assorted documentation fixes.
- Update fb_damage handling, and move drm_plane_enable_fb_damage_clips to core.
- Add logging and docs to RMFB ioctl.
- Assorted small fixes to dp_mst, master handling.
- Clarify drm lease usage.
Driver Changes:
- Assorted small fixes to panfrost, hibmc, bridge/nwl-dsi, rockchip, vc4.
- More drm -> linux irq conversions.
- Add support for some Logic Technologies and Multi-Inno panels.
- Expose phy-functionality for drm/rockchip, to allow controlling from the media subsystem.
- Add support for 2 AUO panels.
- Add damage handling to ssd1307fb.
- Improve FIFO handling on mxsfb.
- Assorted small fixes to vmwgfx, and bump version to 2.19 for the new ioctls.
- Improve sony acx424akp backlight handling.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a753221a-e23e-0dc4-7ca6-8c1b179738d0@linux.intel.com
On all platforms except i.MX and Rockchip, the dw-hdmi DT bindings
require a video output port connected to an HDMI sink (most likely an
HDMI connector, in rare cases another bridges converting HDMI to another
protocol). For those platforms, retrieve the next bridge and attach it
from the dw-hdmi bridge attach handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com> # On V3U
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Being informed of a failure to attach a bridge is useful, and many
drivers prints an error message in that case. Move the message to
drm_bridge_attach() to avoid code duplication.
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Finding panel_or_bridge might vary based on associated
DSI devices like DSI panel, bridge, and I2C based DSI
bridge.
1. DSI panels and bridges will invoke the host attach
from probe in order to find the panel_or_bridge.
chipone_probe()
dw_mipi_dsi_host_attach().start
dw_mipi_dsi_panel_or_bridge()
...found the panel_or_bridge...
ltdc_encoder_init().start
dw_mipi_dsi_bridge_attach().start
dw_mipi_dsi_host_attach().start
chipone_attach(). start
chipone_attach(). done
dw_mipi_dsi_host_attach().done
dw_mipi_dsi_bridge_attach(). done
ltdc_encoder_init().done
2. I2C based DSI bridge will invoke the drm_bridge_attach
from bridge attach in order to find the panel_or_bridge.
ltdc_encoder_init().start
dw_mipi_dsi_bridge_attach().start
dw_mipi_dsi_panel_or_bridge()
...found the panel_or_bridge...
dw_mipi_dsi_host_attach().start
sn65dsi83_attach(). start
sn65dsi83_attach(). done
dw_mipi_dsi_host_attach().done
dw_mipi_dsi_bridge_attach(). done
ltdc_encoder_init().done
So, invoke the panel_or_bridge from host attach and
bridge attach in order to find all possible DSI devices.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Yannick Fertre <yannick.fertre@foss.st.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210704140309.268469-1-jagan@amarulasolutions.com
All the drivers that support the HDR metadata property have a similar
function to compare the metadata from one connector state to the next,
and force a mode change if they differ.
All these functions run pretty much the same code, so let's turn it into
an helper that can be shared across those drivers.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430094451.2145002-2-maxime@cerno.tech
All the drivers that implement HDR output call pretty much the same
function to initialise the hdr_output_metadata property, and while the
creation of that property is in a helper, every driver uses the same
code to attach it.
Provide a helper for it as well
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430094451.2145002-1-maxime@cerno.tech
This adds DW-HDMI driver a glue option to disable loading of the CEC sub-driver.
On some SoCs, the CEC functionality is enabled in the IP config bits, but the
CEC bus is non-functional like on Amlogic SoCs, where the CEC config bit is set
but the DW-HDMI CEC signal is not connected to a physical pin, leading to some
confusion when the DW-HDMI CEC controller can't communicate on the bus.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210416092737.1971876-2-narmstrong@baylibre.com
Because clk_disable_unprepare() already checked NULL clock parameter,
so the additional check is unnecessary, just remove them.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
core:
- documentation updates
- deprecate DRM_FORMAT_MOD_NONE
- atomic crtc enable/disable rework
- GEM convert drivers to gem object functions
- remove SCATTER_LIST_MAX_SEGMENT
sched:
- avoid infinite waits
ttm:
- remove AGP support
- don't modify caching for swapout
- ttm pinning rework
- major TTM reworks
- new backend allocator
- multihop support
vram-helper:
- top down BO placement fix
- TTM changes
- GEM object support
displayport:
- DP 2.0 DPCD prep work
- DP MST extended DPCD caps
fbdev:
- mark as orphaned
amdgpu:
- Initial Vangogh support
- Green Sardine support
- Dimgrey Cavefish support
- SG display support for renoir
- SMU7 improvements
- gfx9+ modiifier support
- CI BACO fixes
radeon:
- expose voltage via hwmon on SUMO
amdkfd:
- fix unique id handling
i915:
- more DG1 enablement
- bigjoiner support
- integer scaling filter support
- async flip support
- ICL+ DSI command mode
- Improve display shutdown
- Display refactoring
- eLLC machine fbdev loading fix
- dma scatterlist fixes
- TGL hang fixes
- eLLC display buffer caching on SKL+
- MOCS PTE seeting for gen9+
msm:
- Shutdown hook
- GPU cooling device support
- DSI 7nm and 10nm phy/pll updates
- sm8150/sm2850 DPU support
- GEM locking re-work
- LLCC system cache support
aspeed:
- sysfs output config support
ast:
- LUT fix
- new display mode
gma500:
- remove 2d framebuffer accel
panfrost:
- move gpu reset to a worker
exynos:
- new HDMI mode support
mediatek:
- MT8167 support
- yaml bindings
- MIPI DSI phy code moved
etnaviv:
- new perf counter
- more lockdep annotation
hibmc:
- i2c DDC support
ingenic:
- pixel clock reset fix
- reserved memory support
- allow both DMA channels at once
- different pixel format support
- 30/24/8-bit palette modes
tilcdc:
- don't keep vblank irq enabled
vc4:
- new maintainer added
- DSI registration fix
virtio:
- blob resource support
- host visible and cross-device support
- uuid api support
-----BEGIN PGP SIGNATURE-----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=c9rl
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-12-11' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Not a huge amount of big things here, AMD has support for a few new HW
variants (vangogh, green sardine, dimgrey cavefish), Intel has some
more DG1 enablement. We have a few big reworks of the TTM layers and
interfaces, GEM and atomic internal API reworks cross tree. fbdev is
marked orphaned in here as well to reflect the current reality.
core:
- documentation updates
- deprecate DRM_FORMAT_MOD_NONE
- atomic crtc enable/disable rework
- GEM convert drivers to gem object functions
- remove SCATTER_LIST_MAX_SEGMENT
sched:
- avoid infinite waits
ttm:
- remove AGP support
- don't modify caching for swapout
- ttm pinning rework
- major TTM reworks
- new backend allocator
- multihop support
vram-helper:
- top down BO placement fix
- TTM changes
- GEM object support
displayport:
- DP 2.0 DPCD prep work
- DP MST extended DPCD caps
fbdev:
- mark as orphaned
amdgpu:
- Initial Vangogh support
- Green Sardine support
- Dimgrey Cavefish support
- SG display support for renoir
- SMU7 improvements
- gfx9+ modiifier support
- CI BACO fixes
radeon:
- expose voltage via hwmon on SUMO
amdkfd:
- fix unique id handling
i915:
- more DG1 enablement
- bigjoiner support
- integer scaling filter support
- async flip support
- ICL+ DSI command mode
- Improve display shutdown
- Display refactoring
- eLLC machine fbdev loading fix
- dma scatterlist fixes
- TGL hang fixes
- eLLC display buffer caching on SKL+
- MOCS PTE seeting for gen9+
msm:
- Shutdown hook
- GPU cooling device support
- DSI 7nm and 10nm phy/pll updates
- sm8150/sm2850 DPU support
- GEM locking re-work
- LLCC system cache support
aspeed:
- sysfs output config support
ast:
- LUT fix
- new display mode
gma500:
- remove 2d framebuffer accel
panfrost:
- move gpu reset to a worker
exynos:
- new HDMI mode support
mediatek:
- MT8167 support
- yaml bindings
- MIPI DSI phy code moved
etnaviv:
- new perf counter
- more lockdep annotation
hibmc:
- i2c DDC support
ingenic:
- pixel clock reset fix
- reserved memory support
- allow both DMA channels at once
- different pixel format support
- 30/24/8-bit palette modes
tilcdc:
- don't keep vblank irq enabled
vc4:
- new maintainer added
- DSI registration fix
virtio:
- blob resource support
- host visible and cross-device support
- uuid api support"
* tag 'drm-next-2020-12-11' of git://anongit.freedesktop.org/drm/drm: (1754 commits)
drm/amdgpu: Initialise drm_gem_object_funcs for imported BOs
drm/amdgpu: fix size calculation with stolen vga memory
drm/amdgpu: remove amdgpu_ttm_late_init and amdgpu_bo_late_init
drm/amdgpu: free the pre-OS console framebuffer after the first modeset
drm/amdgpu: enable runtime pm using BACO on CI dGPUs
drm/amdgpu/cik: enable BACO reset on Bonaire
drm/amd/pm: update smu10.h WORKLOAD_PPLIB setting for raven
drm/amd/pm: remove one unsupported smu function for vangogh
drm/amd/display: setup system context for APUs
drm/amd/display: add S/G support for Vangogh
drm/amdkfd: Fix leak in dmabuf import
drm/amdgpu: use AMDGPU_NUM_VMID when possible
drm/amdgpu: fix sdma instance fw version and feature version init
drm/amd/pm: update driver if version for dimgrey_cavefish
drm/amd/display: 3.2.115
drm/amd/display: [FW Promotion] Release 0.0.45
drm/amd/display: Revert DCN2.1 dram_clock_change_latency update
drm/amd/display: Enable gpu_vm_support for dcn3.01
drm/amd/display: Fixed the audio noise during mode switching with HDCP mode on
drm/amd/display: Add wm table for Renoir
...
It has been observed that resetting force in the detect function can
result in the PHY being powered down in response to hot-plug detect
being asserted, even when the HDMI connector is forced on.
Enabling debug messages and adding a call to dump_stack() in
dw_hdmi_phy_power_off() shows the following in dmesg:
[ 160.637413] dwhdmi-rockchip ff940000.hdmi: EVENT=plugin
[ 160.637433] dwhdmi-rockchip ff940000.hdmi: PHY powered down in 0 iterations
Call trace:
dw_hdmi_phy_power_off
dw_hdmi_phy_disable
dw_hdmi_update_power
dw_hdmi_detect
dw_hdmi_connector_detect
drm_helper_probe_detect_ctx
drm_helper_hpd_irq_event
dw_hdmi_irq
irq_thread_fn
irq_thread
kthread
ret_from_fork
Fixes: 381f05a7a8 ("drm: bridge/dw_hdmi: add connector mode forcing")
Signed-off-by: Jonathan Liu <net147@gmail.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201031081747.372599-1-net147@gmail.com
The only usage of dw_hdmi_i2s_ops is to assign its address to the ops
field in the hdmi_codec_pdata struct, which is a const pointer. Make it
const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201004200653.14702-1-rikard.falkeborn@gmail.com
kmemdup can be used instead of kmalloc+memcpy. Replace an occurrence of
this pattern.
Issue identified with Coccinelle.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200909190213.156302-1-alex.dewar90@gmail.com
This fixes the following warnings while building in W=1 :
dw-mipi-dsi.c:1002:5: warning: no previous prototype for 'dw_mipi_dsi_debugfs_write' [-Wmissing-prototypes]
dw-mipi-dsi.c:1027:5: warning: no previous prototype for 'dw_mipi_dsi_debugfs_show' [-Wmissing-prototypes]
Fixes: e2435d6920 ("drm/bridge: dw-mipi-dsi.c: Add VPG runtime config through debugfs")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Angelo Ribeiro <angelo.ribeiro@synopsys.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200907102711.23748-1-narmstrong@baylibre.com
Add support for the video pattern generator (VPG) BER pattern mode and
configuration in runtime.
This enables using the debugfs interface to manipulate the VPG after
the pipeline is set.
Also, enables the usage of the VPG BER pattern.
Changes in v2:
- Added VID_MODE_VPG_MODE
- Solved incompatible return type on __get and __set
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Adrian Pop <pop.adrian61@gmail.com>
Signed-off-by: Angelo Ribeiro <angelo.ribeiro@synopsys.com>
Tested-by: Yannick Fertre <yannick.fertre@st.com>
Tested-by: Adrian Pop <pop.adrian61@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Jose Abreu <jose.abreu@synopsys.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a809feb7d7153a92e323416f744f1565e995da01.1586180592.git.angelo.ribeiro@synopsys.com
Current code enables the HS clock when video mode is started or to
send out a HS command, and disables the HS clock to send out a LP
command. This is not what DSI spec specify.
Enable HS clock either in command and in video mode.
Set automatic HS clock management for panels and devices that
support non-continuous HS clock.
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701194234.18123-1-yannick.fertre@st.com
Current code does not properly computes the max length of LP
commands that can be send during H or V sync, and rely on static
values.
Limiting the max LP length to 4 byte during the V-sync is overly
conservative.
Relax the limit and allows longer LP commands (16 bytes) to be
sent during V-sync.
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701143131.841-1-yannick.fertre@st.com
Current code only sends LP commands in command mode.
Allows sending LP commands also in video mode by setting the
proper flag in DSI_VID_MODE_CFG.
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200708140836.32418-1-yannick.fertre@st.com
It doesn't hurt to add the bridge in the global bridge list also for
platform specific dw-hdmi drivers which are based on the component
framework. This can be achieved by moving the drm_bridge_add() function
call from dw_hdmi_probe() to __dw_hdmi_probe(). A counterpart movement
for drm_bridge_remove() is also needed then. Moreover, since drm_bridge_add()
initializes &bridge->hpd_mutex, this may help those platform specific
dw-hdmi drivers(based on the component framework) avoid accessing the
uninitialized mutex in drm_bridge_hpd_notify() which is called in
dw_hdmi_irq(). Putting drm_bridge_add() in __dw_hdmi_probe() just before
it returns successfully should bring no logic change for platforms based
on the DRM bridge API, which is a good choice from safety point of view.
Also, __dw_hdmi_probe() is renamed to dw_hdmi_probe() since dw_hdmi_probe()
does nothing else but calling __dw_hdmi_probe(). Similar renaming applies
to the __dw_hdmi_remove()/dw_hdmi_remove() pair.
Fixes: ec971aaa67 ("drm: bridge: dw-hdmi: Make connector creation optional")
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Cheng-Yi Chiang <cychiang@chromium.org>
Cc: Dariusz Marcinkiewicz <darekm@google.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: dri-devel@lists.freedesktop.org
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1594260156-8316-2-git-send-email-victor.liu@nxp.com
It's unnecessary to cleanup the i2c adapter and the ddc pointer in
the bailout path of __dw_hdmi_probe(), since the adapter is not
added and the ddc pointer is not set.
Fixes: a23d6265f0 ("drm: bridge: dw-hdmi: Extract PHY interrupt setup to a function")
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Cheng-Yi Chiang <cychiang@chromium.org>
Cc: Dariusz Marcinkiewicz <darekm@google.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: dri-devel@lists.freedesktop.org
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1594260156-8316-1-git-send-email-victor.liu@nxp.com
Some conflicts with ttm_bo->offset removal, but drm-misc-next needs updating to v5.8.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
dw-mipi-dsi does not use any definition from drm_probe_helper.
Coverity output:
Event unnecessary_header:
Including .../include/drm/drm_probe_helper.h does not provide any
needed symbols.
Reviewed-by: Yannick Fertre <yannick.fertre@st.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Jose Abreu <jose.abreu@synopsys.com>
Signed-off-by: Angelo Ribeiro <angelo.ribeiro@synopsys.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/171ff1fb3918664a570dc8f2f34b446612505f76.1585832665.git.angelo.ribeiro@synopsys.com
Implement the drm_bridge_funcs .detect() and .get_edid() operations, and
call drm_bridge_hpd_notify() notify to report HPD. This provides the
necessary API to support disabling connector creation, do so by
accepting DRM_BRIDGE_ATTACH_NO_CONNECTOR in dw_hdmi_bridge_attach().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-23-laurent.pinchart+renesas@ideasonboard.com
To prepare for making connector creation optional in the driver, pass
the drm_connector explicitly to the internal functions that require it.
The functions that still access the connector from the dw_hdmi structure
are dw_hdmi_connector_create() and __dw_hdmi_probe(). The former access
is expected, as that's where the internal connector is created. The
latter will be addressed separately.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-22-laurent.pinchart+renesas@ideasonboard.com
Store the connector that the bridge is currently wired to in the dw_hdmi
structure. This is currently identical to the connector field, but will
differ once the driver supports disabling connector creation.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-21-laurent.pinchart+renesas@ideasonboard.com
To prepare for making connector creation optional in the driver, pass
the drm_display_info explicitly to dw_hdmi_support_scdc(). The pointer
is passed to the callers where required, particularly to the
dw_hdmi_phy_ops .init() function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-19-laurent.pinchart+renesas@ideasonboard.com
Several internal functions take a drm_display_mode argument to configure
the HDMI encoder or the HDMI PHY. They must not modify the mode, make
the pointer const to enforce that.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-18-laurent.pinchart+renesas@ideasonboard.com
Replace the drm_connector pointer passed to the .mode_valid() function
with a const drm_display_info pointer, as that's all the function should
need. Use the display info passed to the bridge .mode_valid() operation
instead of retrieving it from the connector, to prepare for make
connector creation optional.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-16-laurent.pinchart+renesas@ideasonboard.com
The .configure_phy() operation takes a dw_hdmi_plat_data pointer as a
context argument. This differs from .mode_valid() that takes a custom
private context pointer, causing possible confusion. Make the
dw_hdmi_plat_data operations more consistent by passing the private
context pointer to .configure_phy() as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-13-laurent.pinchart+renesas@ideasonboard.com
Platform glue drivers for dw_hdmi may need to access device-specific
data from their .mode_valid() implementation. They currently have no
clean way to do so, and one driver hacks around it by accessing the
dev_private data of the drm_device retrieved from the connector.
Add a priv_data void pointer to the dw_hdmi_plat_data structure, and
pass it to the .mode_valid() function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-12-laurent.pinchart+renesas@ideasonboard.com
When validating a mode, bridges may need to do so in the context of a
display, as specified by drm_display_info. An example is the meson
dw-hdmi bridge that needs to consider the YUV 4:2:0 output format to
perform clock calculations.
Bridges that need the display info currently retrieve it from the
drm_connector created by the bridge. This gets in the way of moving
connector creation out of bridge drivers. To make this possible, pass
the drm_display_info to drm_bridge_funcs .mode_valid().
Changes to the bridge drivers have been performed with the following
coccinelle semantic patch and have been compile-tested.
@ rule1 @
identifier funcs;
identifier fn;
@@
struct drm_bridge_funcs funcs = {
...,
.mode_valid = fn
};
@ depends on rule1 @
identifier rule1.fn;
identifier bridge;
identifier mode;
@@
enum drm_mode_status fn(
struct drm_bridge *bridge,
+ const struct drm_display_info *info,
const struct drm_display_mode *mode
)
{
...
}
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org> # for the nwl-dsi part:
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-11-laurent.pinchart+renesas@ideasonboard.com
Globally update my email address in six files scattered through the
tree.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl6BIG4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGlHUH/RCFve2sfHRPjRW+
xR5SaLVAw6XKvtKBq7yvKmHEwqNJnL79IHyqqtSrtfFr2FfaH/KvYiCbbAezvSrM
np0udGu7STKGd21CWuyEZJudyhXkOwMRNiFiCXWp7rs35oh8T0TpJxMzo2Nc1nLk
JFQPqAP6OSvq4IkWEywKQI+Au3Z1IBf83xVjZ1s+MKPQHYD49x2hc4cQntL5/cnm
a3DoR2iBkYiGZCZ9dDqAqJTnMQIiCbACdZXgGjNRUpdyA/dtAjsMl11NPYHm8TA2
3AHBupAK50WBZGad6xv2qKQyScsmoJG2mv92QjlOFz0Tpiu6rLnDlLYREDVB6YH6
qbLDsc8=
=XEIU
-----END PGP SIGNATURE-----
Merge v5.6 into drm-next
msm needed rc6, so I just went and merged release
(msm has been in drm-next outside of this tree)
Signed-off-by: Dave Airlie <airlied@redhat.com>
is_color_space_conversion() is a misnomer. It checks not only if color
space conversion is needed, but also if format conversion is needed.
This is actually desired behaviour because result of this function
determines if CSC block should be enabled or not (CSC block can also do
format conversion).
In order to clear misunderstandings, let's rework
is_color_space_conversion() to do exactly what is supposed to do and add
another function which will determine if CSC block must be enabled or
not.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304232512.51616-5-jernej.skrabec@siol.net
CEA 861 standard requestis that RGB quantization range is "limited" for
CEA modes. Support that by adding CSC matrix which downscales values.
This allows proper color reproduction on TV and PC monitor at the same
time. In future, override property can be added, like "Broadcast RGB"
in i915 driver.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304232512.51616-4-jernej.skrabec@siol.net
Setting scan mode to "none" confuses some TVs like LG B8, which randomly
change overscan percentage over time. Digital outputs like HDMI and DVI,
handled by this controller, don't really need overscan, so we can always
set scan mode to underscan. Actually, this is exactly what
drm_hdmi_avi_infoframe_from_display_mode() already does, so we can just
remove offending line.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
[updated commit message]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304232512.51616-3-jernej.skrabec@siol.net
Now the DW-HDMI Controller supports the HDMI2.0 modes, enable support
for these modes in the connector if the platform supports them.
We limit these modes to DW-HDMI IP version >= 0x200a which
are designed to support HDMI2.0 display modes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-6-narmstrong@baylibre.com
Add the atomic_get_output_bus_fmts, atomic_get_input_bus_fmts to negociate
the possible output and input formats for the current mode and monitor,
and use the negotiated formats in a basic atomic_check callback.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-5-narmstrong@baylibre.com
Add the max_bpc property to the dw-hdmi connector to prepare support
for 10, 12 & 16bit output support.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-3-narmstrong@baylibre.com
Most bridge drivers create a DRM connector to model the connector at the
output of the bridge. This model is historical and has worked pretty
well so far, but causes several issues:
- It prevents supporting more complex display pipelines where DRM
connector operations are split over multiple components. For instance a
pipeline with a bridge connected to the DDC signals to read EDID data,
and another one connected to the HPD signal to detect connection and
disconnection, will not be possible to support through this model.
- It requires every bridge driver to implement similar connector
handling code, resulting in code duplication.
- It assumes that a bridge will either be wired to a connector or to
another bridge, but doesn't support bridges that can be used in both
positions very well (although there is some ad-hoc support for this in
the analogix_dp bridge driver).
In order to solve these issues, ownership of the connector should be
moved to the display controller driver (where it can be implemented
using helpers provided by the core).
Extend the bridge API to allow disabling connector creation in bridge
drivers as a first step towards the new model. The new flags argument to
the bridge .attach() operation allows instructing the bridge driver to
skip creating a connector. Unconditionally set the new flags argument to
0 for now to keep the existing behaviour, and modify all existing bridge
drivers to return an error when connector creation is not requested as
they don't support this feature yet.
The change is based on the following semantic patch, with manual review
and edits.
@ rule1 @
identifier funcs;
identifier fn;
@@
struct drm_bridge_funcs funcs = {
...,
.attach = fn
};
@ depends on rule1 @
identifier rule1.fn;
identifier bridge;
statement S, S1;
@@
int fn(
struct drm_bridge *bridge
+ , enum drm_bridge_attach_flags flags
)
{
... when != S
+ if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) {
+ DRM_ERROR("Fix bridge driver to make connector optional!");
+ return -EINVAL;
+ }
+
S1
...
}
@ depends on rule1 @
identifier rule1.fn;
identifier bridge, flags;
expression E1, E2, E3;
@@
int fn(
struct drm_bridge *bridge,
enum drm_bridge_attach_flags flags
) {
<...
drm_bridge_attach(E1, E2, E3
+ , flags
)
...>
}
@@
expression E1, E2, E3;
@@
drm_bridge_attach(E1, E2, E3
+ , 0
)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-10-laurent.pinchart@ideasonboard.com
The dw_hdmi_hw structure is only copied into another structure,
so make it const.
The opportunity for this change was found using Coccinelle.
Fixes: 7ed6c665e1 ("drm: bridge/dw_hdmi-ahb-audio: add audio driver")
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1577864614-5543-16-git-send-email-Julia.Lawall@inria.fr
