Make sure the controller is in a basic working state after runtime
resume. Keep the analog function enable in the mode set path as this
enables parts of the PHY that are only required to be powered when
there is a data stream being sent out.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-8-l.stach@pengutronix.de
Platform and PHY power isn't only required when the actual display data
stream is active, but may be required earlier to support AUX channel
transactions. Move them into the runtime PM calls, so they are properly
managed whenever various other parts of the driver need them to be active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-7-l.stach@pengutronix.de
The clock is already managed by runtime PM, which is properly invoked
from the analogix_dp_set_bridge function, so there is no need for an
additional reference.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-6-l.stach@pengutronix.de
Now that the clock is handled dynamically through
analogix_dp_resume/suspend and it isn't statically enabled in the
driver probe routine, there is no need for the remove function anymore.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-5-l.stach@pengutronix.de
There is no reason to enable the controller clock in driver probe, as
there is no HW initialization done in this function. Instead rely on
either runtime PM to handle the controller clock or statically enable
it in the driver bind routine, after which real hardware access is
required to work.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-4-l.stach@pengutronix.de
AUX transactions require the controller to be in working state and
take a runtime PM reference. To avoid potential races beween the
first transactions on the bus and runtime PM being set up, move the
AUX registration behind the runtime PM setup.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-3-l.stach@pengutronix.de
This isn't used, but gives the impression of the power on and power off
platform calls being non-symmetrical. Remove the unused callback and
rename the power_on_start to simply power_on.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-1-l.stach@pengutronix.de
Take a early return from the clock recovery training when the sink reports
CR_DONE for all lanes. There is no point in trying to adjust the link
parameters further.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240318203925.2837689-3-l.stach@pengutronix.de
There is no need for separate functions for each lane, as we can deduct the
register offset to read/write from the lane index.
Signed-off-by: Wyon Bi <bivvy.bi@rock-chips.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240318203925.2837689-2-l.stach@pengutronix.de
The checks on the existence of bridge->encoder in the implementation of
drm_bridge_funcs::attach() is not necessary, as it has already been checked
in the drm_bridge_attach() function call by previous bridge or KMS driver.
The drm_bridge_attach() will quit with a negative error code returned if
it fails for some reasons, hence, it is guaranteed that the .encoder member
of the drm_bridge instance is not NULL when various bridge attach functions
are called.
Remove the redundant checking codes "if (!bridge->encoder) { ... }".
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240513153109.46786-13-sui.jingfeng@linux.dev
This reverts commit e075e496f5, as helper
code should always be selected by the driver that needs it, for the
convenience of the final user configuring a kernel.
The user who configures a kernel should not need to know which helpers
are needed for the driver he is interested in. Making a driver depend
on helper code means that the user needs to know which helpers to enable
first, which is very user-unfriendly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1ba76cc4d96a8afefff5d1bc42fb1e1329c5da68.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <mripard@kernel.org>
This reverts commit 4d15125d7f, as helper
code should always be selected by the driver that needs it, for the
convenience of the final user configuring a kernel.
The user who configures a kernel should not need to know which helpers
are needed for the driver he is interested in. Making a driver depend
on helper code means that the user needs to know which helpers to enable
first, which is very user-unfriendly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patchwork.freedesktop.org/patch/msgid/79824fec01eb9ab0673b9409f9b39cc8b5cc338d.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <mripard@kernel.org>
This reverts commit 0323287de8, as helper
code should always be selected by the driver that needs it, for the
convenience of the final user configuring a kernel.
The user who configures a kernel should not need to know which helpers
are needed for the driver he is interested in. Making a driver depend
on helper code means that the user needs to know which helpers to enable
first, which is very user-unfriendly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patchwork.freedesktop.org/patch/msgid/89ac456805746b6d0c888f10c5120b11aacd3319.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <mripard@kernel.org>
This reverts commit 3166e7e6d9, as helper
code should always be selected by the driver that needs it, for the
convenience of the final user configuring a kernel.
The user who configures a kernel should not need to know which helpers
are needed for the driver he is interested in. Making a driver depend
on helper code means that the user needs to know which helpers to enable
first, which is very user-unfriendly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patchwork.freedesktop.org/patch/msgid/a40e70a0abd3d841c23c107d452a43fdd70ef37a.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Previously, the audio status was not updated during detection, leading
to a persistent audio despite hot plugging events. To resolve this
issue, update the audio status during detection.
Fixes: 566fef1226 ("drm/bridge: anx7625: add HDMI audio function")
Signed-off-by: Hsin-Te Yuan <yuanhsinte@chromium.org>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240416-anx7625-v3-1-f916ae31bdd7@chromium.org
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: 269332997a ("drm/bridge: anx7625: Return -EPROBE_DEFER if the dsi host was not found")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-1-619a28148e5c@collabora.com
After my fix yesterday, I ran into another problem of the same kind:
aarch64-linux-ld: drivers/gpu/drm/bridge/analogix/analogix_dp_core.o: in function `drm_dp_dpcd_readb':
analogix_dp_core.c:(.text+0x194): undefined reference to `drm_dp_dpcd_read'
aarch64-linux-ld: drivers/gpu/drm/bridge/analogix/analogix_dp_core.o: in function `drm_dp_dpcd_writeb':
analogix_dp_core.c:(.text+0x214): undefined reference to `drm_dp_dpcd_write'
aarch64-linux-ld: drivers/gpu/drm/bridge/analogix/analogix_dp_core.o: in function `analogix_dp_stop_crc':
analogix_dp_core.c:(.text+0x4b0): undefined reference to `drm_dp_stop_crc'
aarch64-linux-ld: drivers/gpu/drm/bridge/analogix/analogix_dp_core.o: in function `analogix_dp_start_crc':
analogix_dp_core.c:(.text+0xbe8): undefined reference to `drm_dp_start_crc'
Add the same dependency again to ROCKCHIP_ANALOGIX_DP after checking that
nothing else selects the analogix driver. Also add a dependency to
DRM_ANALOGIX_DP to make it easier to identifier future problems of
this type when they get introduced.
Fixes: 0323287de8 ("drm: Switch DRM_DISPLAY_DP_HELPER to depends on")
Fixes: d1ef8fc18b ("drm: fix DRM_DISPLAY_DP_HELPER dependencies")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240405143531.925589-1-arnd@kernel.org
Most of our helpers have relied on being selected so far through
Kconfig, but that creates issues when we have multiple layers of helpers
with some depending on others.
Indeed, select doesn't select a dependency's dependencies, and thus
isn't super intuitive. Depends on however doesn't have that limitation,
so we can just switch all the drivers that were selecting
DRM_DISPLAY_HDCP_HELPER to depend on it.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-11-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Most of our helpers have relied on being selected so far through
Kconfig, but that creates issues when we have multiple layers of helpers
with some depending on others.
Indeed, select doesn't select a dependency's dependencies, and thus
isn't super intuitive. Depends on however doesn't have that limitation,
so we can just switch all the drivers that were selecting
DRM_DISPLAY_DP_HELPER to depend on it.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-10-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Most of our helpers have relied on being selected so far through
Kconfig, but that creates issues when we have multiple layers of helpers
with some depending on others.
Indeed, select doesn't select a dependency's dependencies, and thus
isn't super intuitive. Depends on however doesn't have that limitation,
so we can just switch all the drivers that were selecting
DRM_DISPLAY_DP_AUX_BUS to depend on it.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-9-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Most of our helpers have relied on being selected so far through
Kconfig, but that creates issues when we have multiple layers of helpers
with some depending on others.
Indeed, select doesn't select a dependency's dependencies, and thus
isn't super intuitive. Depends on however doesn't have that limitation,
so we can just switch all the drivers that were selecting
DRM_DISPLAY_HELPER to depend on it.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-8-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
While most display helpers Kconfig symbols have the DRM_DISPLAY prefix,
the DisplayPort AUX bus implementation uses DRM_DP_AUX_BUS.
Since the number of users is limited and it's a selected symbol, we can
easily rename it to make it consistent.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-1-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Similar to commit 26db46bc9c ("drm/bridge: parade-ps8640: Ensure bridge
is suspended in .post_disable()"). Add a mutex to ensure that aux transfer
won't race with atomic_disable by holding the PM reference and prevent
the bridge from suspend.
Also we need to use pm_runtime_put_sync_suspend() to suspend the bridge
instead of idle with pm_runtime_put_sync().
Fixes: 3203e497eb ("drm/bridge: anx7625: Synchronously run runtime suspend.")
Fixes: adca62ec37 ("drm/bridge: anx7625: Support reading edid through aux channel")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Tested-by: Xuxin Xiong <xuxinxiong@huaqin.corp-partner.google.com>
Reviewed-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240118015916.2296741-1-hsinyi@chromium.org
For the no-interrupt design (sink device is panel, polling HPD
status when chip power on), anx7625 FW has more than 200ms HPD
de-bounce time in FW, for the safety to get HPD status, driver
better to wait 200ms before HPD detection after OS resume back.
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230922093450.3574349-1-xji@analogixsemi.com
Analogix ANX78XX driver is missing definitions for anx7816.
It uses the same I2C register set as anx7818.
Signed-off-by: Alicja Michalska <ahplka19@gmail.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/ZPvagaXnQ/TlNEkJ@tora
Having conditional around the of_node pointers turns out to make driver
code use ugly #ifdef and #if blocks. So drop the conditionals.
Suggested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230831080938.47454-4-biju.das.jz@bp.renesas.com
The driver has an ID table, but it uses the wrong API for retrieving match
data and that will lead to a crash, if it is instantiated by user space or
using ID. From this, there is no user for the ID table and let's drop it
from the driver as it saves some memory.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230831080938.47454-2-biju.das.jz@bp.renesas.com
When building with W=1, the following warning occurs.
drivers/gpu/drm/bridge/analogix/analogix-anx78xx.c:48:17: warning: ‘anx781x_i2c_addresses’ defined but not used [-Wunused-const-variable=] static const u8 anx781x_i2c_addresses[] = {
^~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/bridge/analogix/analogix-anx78xx.c:40:17: warning: ‘anx7808_i2c_addresses’ defined but not used [-Wunused-const-variable=] static const u8 anx7808_i2c_addresses[] = {
When CONFIG_IO is disabled, above two variables are not used,
since the place where it is used is inclueded in the macro
CONFIG_OF.
Even for drivers that do not depend on CONFIG_OF, it's almost
always better to leave out the of_match_ptr(), since the only
thing it can possibly do is to save a few bytes of .text if a
driver can be used both with and without it. Hence we remove
all of_match_ptr() used in other places.
Fixes: 0647e7dd3f ("drm/bridge: Add Analogix anx78xx support")
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230731021345.219588-1-wangzhu9@huawei.com
These two drivers embed a i2c_client in their private driver data, but
only strict device is actually needed. Replace the i2c_client reference
with a struct device one.
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230718110407.1005200-1-wenst@chromium.org
The device lock is used to serialize the low level power sequencing
operations. Since drm_helper_hpd_irq_event() could end up calling
.atomic_enable, which also calls power sequencing functions through
runtime PM, this results in a real deadlock. This was observed on an
MT8192-based Chromebook's external display (with appropriate patches [1]
and DT changes applied).
Move the drm_helper_hpd_irq_event() call outside of the lock range. The
lock only needs to be held so that the device status can be read back.
This is the bare minimum change to avoid the deadlock. The lock could
be dropped completely and have pm_runtime_get_if_in_use() increase the
reference count, but this is not the same as pm_runtime_suspended().
Dropping the lock completely also causes the internal display of the
same device to not function correctly if the internal bridge's
interrupt line is added in the device tree. Both the internal and
external display of said device each use one anx7625 bridge.
[1] https://lore.kernel.org/dri-devel/20230112042104.4107253-1-treapking@chromium.org/
Fixes: 60487584a7 ("drm/bridge: anx7625: refactor power control to use runtime PM framework")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230710085922.1871465-1-wenst@chromium.org
The DRM DP code has macros for the DP HDCP capabilities. Use them in the
anx7625 driver instead of raw numbers.
Fixes: cd1637c7e4 ("drm/bridge: anx7625: add HDCP support")
Suggested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230710091203.1874317-1-wenst@chromium.org
The DRM DP code has macros for the DP power sequencing commands. Use
them in the anx7625 driver instead of raw numbers.
Fixes: 548b512e14 ("drm/bridge: anx7625: send DPCD command to downstream")
Fixes: 27f26359de ("drm/bridge: anx7625: Set downstream sink into normal status")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230710090929.1873646-1-wenst@chromium.org
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230526090709.1517297-1-u.kleine-koenig@pengutronix.de
During probe, the driver registers i2c dummy devices and populates the
aux bus, which registers a device for the panel. After doing that, the
driver can still defer probe if needed. This ordering of operations is
troublesome however, because the deferred probe work will retry probing
all pending devices every time a new device is registered. Therefore, if
modules need to be loaded in order to satisfy the dependencies for this
driver to complete probe, the kernel will stall, since it'll keep trying
to probe the anx7625 driver, but never succeed, given that modules would
only be loaded after the deferred probe work completes.
Two changes are required to avoid this issue:
* Move of_find_mipi_dsi_host_by_node(), which can defer probe, to before
anx7625_register_i2c_dummy_clients() and
devm_of_dp_aux_populate_ep_devices(), which register devices.
* Make use of the done_probing callback when populating the aux bus,
so that the bridge registration is only done after the panel is
probed. This is required because the panel might need to defer probe,
but the aux bus population needs the i2c dummy devices working, so
this call couldn't just be moved to an earlier point in probe.
One caveat is that if the panel is described outside the aux bus, the
probe loop issue can still happen, but we don't have a way to avoid
it in that case since there's no callback available.
With this patch applied, it's possible to boot on
mt8192-asurada-spherion with
CONFIG_DRM_ANALOGIX_ANX7625=y
CONFIG_MTK_MMSYS=m
CONFIG_BACKLIGHT_PWM=y
and also with
CONFIG_DRM_ANALOGIX_ANX7625=y
CONFIG_MTK_MMSYS=y
CONFIG_BACKLIGHT_PWM=m
Fixes: adca62ec37 ("drm/bridge: anx7625: Support reading edid through aux channel")
Fixes: 269332997a ("drm/bridge: anx7625: Return -EPROBE_DEFER if the dsi host was not found")
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230518193902.891121-1-nfraprado@collabora.com
This driver includes the deprecated OF GPIO header <linux/of_gpio.h>
yet fail to use symbols from it, so drop the include.
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220812205746.609107-2-mairacanal@riseup.net
Several source files include drm_crtc_helper.h without needing it or
only to get its transitive include statements; leading to unnecessary
compile-time dependencies.
Drop drm_crtc_helper.h where possible.
v2:
* update commit message (Sam)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230116131235.18917-8-tzimmermann@suse.de
Sometimes kernel may resume back quickly after suspend,
and DRM not call .mode_set() to re-config
display timing before calling .atomic_enable(), bridge
driver with this patch to keep last configure timing.
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Acked-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221209030418.713935-1-xji@analogixsemi.com
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20221118224540.619276-18-uwe@kleine-koenig.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20221118224540.619276-17-uwe@kleine-koenig.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20221118224540.619276-16-uwe@kleine-koenig.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
core:
- convert selftests to kunit
- managed init for more objects
- move to idr_init_base
- rename fb and gem cma helpers to dma
- hide unregistered connectors from getconnector ioctl
- DSC passthrough aux support
- backlight handling improvements
- add dma_resv_assert_held to vmap/vunmap
edid:
- move luminance calculation to core
fbdev:
- fix aperture helper usage
fourcc:
- add more format helpers
- add DRM_FORMAT_Cxx, DRM_FORMAT_Rxx, DRM_FORMAT_Dxx
- add packed AYUV8888, XYUV8888
- add some kunit tests
ttm:
- allow bos without backing store
- rewrite placement to use intersect/compatible functions
dma-buf:
- docs update
- improve signalling when debugging
udmabuf:
- fix failure path GPF
dp:
- drop dp/mst legacy code
- atomic mst state support
- audio infoframe packing
panel:
- Samsung LTL101AL01
- B120XAN01.0
- R140NWF5 RH
- DMT028VGHMCMI-1A T
- AUO B133UAN02.1
- IVO M133NW4J-R3
- Innolux N120ACA-EA1
amdgpu:
- Gang submit support
- Mode2 reset for RDNA2
- New IP support:
DCN 3.1.4, 3.2
SMU 13.x
NBIO 7.7
GC 11.x
PSP 13.x
SDMA 6.x
GMC 11.x
- DSC passthrough support
- PSP fixes for TA support
- vangogh GFXOFF stats
- clang fixes
- gang submit CS cleanup prep work
- fix VRAM eviction issues
amdkfd:
- GC 10.3 IP ISA fixes
- fix CRIU regression
- CPU fault on COW mapping fixes
i915:
- align fw versioning with kernel practices
- add display substruct to i915 private
- add initial runtime info to driver info
- split out HDCP and backlight registers
- MEI XeHP SDV GSC support
- add per-gt sysfs defaults
- TLB invalidation improvements
- Disable PCI BAR resize on 32-bit
- GuC firmware updates and compat changes
- GuC log timestamp translation
- DG2 preemption workaround changes
- DG2 improved HDMI pixel clocks support
- PCI BAR sanity checks
- Enable DC5 on DG2
- DG2 DMC fw bumped
- ADL-S PCI ID added
- Meteorlake enablement
- Rename ggtt_view to gtt_view
- host RPS fixes
- release mmaps on rpm suspend on discrete
- clocking and dpll refactoring
- VBT definitions and parsing updates
- SKL watermark code extracted to separate file
- allow seamless M/N changes on eDP panels
- BUG_ON removal and cleanups
msm:
- DPU: simplified VBIF configuration
- cleanup CTL interfaces
- DSI: removed unused msm_display_dsc_config struct
- switch regulator calls to new API
- switched to PANEL_BRIDGE for direct attached panels
- DSI_PHY: convert drivers to parent_hws
- DP: cleanup pixel_rate handling
- HDMI: turned hdmi-phy-8996 into OF clk provider
- misc dt-bindings fixes
- choose eDP as primary display if it's available
- support getting interconnects from either the mdss or the mdp5/dpu
device nodes
- gem: Shrinker + LRU re-work:
- adds a shared GEM LRU+shrinker helper and moves msm over to that
- reduces lock contention between retire and submit by avoiding the
need to acquire obj lock in retire path (and instead using resv
seeing obj's busyness in the shrinker
- fix reclaim vs submit issues
- GEM fault injection for triggering userspace error paths
- Map/unmap optimization
- Improved robustness for a6xx GPU recovery
virtio:
- Improve error and edge conditions handling
- Convert to use managed helpers
- stop exposing LINEAR modifier
mgag200:
- split modeset handling per model
udl:
- suspend/disconnect handling improvements
vc4:
- rework HDMI power up
- depend on PM
- better unplugging support
ast:
- resolution handling improvements
ingenic:
- Add JZ4760(B) support
- avoid a modeset when sharpness property is unchanged
- use the new PM ops
it6505:
- power seq and clock updates
ssd130x:
- regmap bulk write
- use atomic helpers instead of simple helpers
via:
- rename via_drv to via_dri1, consolidate all code.
radeon:
- drop DP MST experimental support
- delayed work flush fix
- use time_after
ti-sn65dsi86:
- DP support
mediatek:
- MT8195 DP support
- drop of_gpio header
- remove unneeded result
- small DP code improvements
vkms:
- RGB565, XRGB64 and ARGB64 support
sun4i:
- tv: convert to atomic
rcar-du:
- Synopsys DW HDMI bridge DT bindings update
exynos:
- use drm_display_info.is_hdmi
- correct return of mixer_mode_valid and hdmi_mode_valid
omap:
- refcounting fix
rockchip:
- RK3568 support
- RK3399 gamma support
-----BEGIN PGP SIGNATURE-----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=u/MJ
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2022-10-05' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Lots of stuff all over, some new AMD IP support and gang submit
support. i915 has further DG2 and Meteorlake pieces, and a bunch of
i915 display refactoring. msm has a shrinker rework. There are also a
bunch of conversions to use kunit.
This has two external pieces, some MEI changes needed for future Intel
discrete GPUs. These should be acked by Greg. There is also a cross
maintainer shared tree with some backlight rework from Hans in here.
Core:
- convert selftests to kunit
- managed init for more objects
- move to idr_init_base
- rename fb and gem cma helpers to dma
- hide unregistered connectors from getconnector ioctl
- DSC passthrough aux support
- backlight handling improvements
- add dma_resv_assert_held to vmap/vunmap
edid:
- move luminance calculation to core
fbdev:
- fix aperture helper usage
fourcc:
- add more format helpers
- add DRM_FORMAT_Cxx, DRM_FORMAT_Rxx, DRM_FORMAT_Dxx
- add packed AYUV8888, XYUV8888
- add some kunit tests
ttm:
- allow bos without backing store
- rewrite placement to use intersect/compatible functions
dma-buf:
- docs update
- improve signalling when debugging
udmabuf:
- fix failure path GPF
dp:
- drop dp/mst legacy code
- atomic mst state support
- audio infoframe packing
panel:
- Samsung LTL101AL01
- B120XAN01.0
- R140NWF5 RH
- DMT028VGHMCMI-1A T
- AUO B133UAN02.1
- IVO M133NW4J-R3
- Innolux N120ACA-EA1
amdgpu:
- Gang submit support
- Mode2 reset for RDNA2
- New IP support:
DCN 3.1.4, 3.2
SMU 13.x
NBIO 7.7
GC 11.x
PSP 13.x
SDMA 6.x
GMC 11.x
- DSC passthrough support
- PSP fixes for TA support
- vangogh GFXOFF stats
- clang fixes
- gang submit CS cleanup prep work
- fix VRAM eviction issues
amdkfd:
- GC 10.3 IP ISA fixes
- fix CRIU regression
- CPU fault on COW mapping fixes
i915:
- align fw versioning with kernel practices
- add display substruct to i915 private
- add initial runtime info to driver info
- split out HDCP and backlight registers
- MEI XeHP SDV GSC support
- add per-gt sysfs defaults
- TLB invalidation improvements
- Disable PCI BAR resize on 32-bit
- GuC firmware updates and compat changes
- GuC log timestamp translation
- DG2 preemption workaround changes
- DG2 improved HDMI pixel clocks support
- PCI BAR sanity checks
- Enable DC5 on DG2
- DG2 DMC fw bumped
- ADL-S PCI ID added
- Meteorlake enablement
- Rename ggtt_view to gtt_view
- host RPS fixes
- release mmaps on rpm suspend on discrete
- clocking and dpll refactoring
- VBT definitions and parsing updates
- SKL watermark code extracted to separate file
- allow seamless M/N changes on eDP panels
- BUG_ON removal and cleanups
msm:
- DPU:
simplified VBIF configuration
cleanup CTL interfaces
- DSI:
removed unused msm_display_dsc_config struct
switch regulator calls to new API
switched to PANEL_BRIDGE for direct attached panels
- DSI_PHY: convert drivers to parent_hws
- DP: cleanup pixel_rate handling
- HDMI: turned hdmi-phy-8996 into OF clk provider
- misc dt-bindings fixes
- choose eDP as primary display if it's available
- support getting interconnects from either the mdss or the mdp5/dpu
device nodes
- gem: Shrinker + LRU re-work:
- adds a shared GEM LRU+shrinker helper and moves msm over to that
- reduce lock contention between retire and submit by avoiding the
need to acquire obj lock in retire path (and instead using resv
seeing obj's busyness in the shrinker
- fix reclaim vs submit issues
- GEM fault injection for triggering userspace error paths
- Map/unmap optimization
- Improved robustness for a6xx GPU recovery
virtio:
- improve error and edge conditions handling
- convert to use managed helpers
- stop exposing LINEAR modifier
mgag200:
- split modeset handling per model
udl:
- suspend/disconnect handling improvements
vc4:
- rework HDMI power up
- depend on PM
- better unplugging support
ast:
- resolution handling improvements
ingenic:
- add JZ4760(B) support
- avoid a modeset when sharpness property is unchanged
- use the new PM ops
it6505:
- power seq and clock updates
ssd130x:
- regmap bulk write
- use atomic helpers instead of simple helpers
via:
- rename via_drv to via_dri1, consolidate all code.
radeon:
- drop DP MST experimental support
- delayed work flush fix
- use time_after
ti-sn65dsi86:
- DP support
mediatek:
- MT8195 DP support
- drop of_gpio header
- remove unneeded result
- small DP code improvements
vkms:
- RGB565, XRGB64 and ARGB64 support
sun4i:
- tv: convert to atomic
rcar-du:
- Synopsys DW HDMI bridge DT bindings update
exynos:
- use drm_display_info.is_hdmi
- correct return of mixer_mode_valid and hdmi_mode_valid
omap:
- refcounting fix
rockchip:
- RK3568 support
- RK3399 gamma support"
* tag 'drm-next-2022-10-05' of git://anongit.freedesktop.org/drm/drm: (1374 commits)
drm/amdkfd: Fix UBSAN shift-out-of-bounds warning
drm/amdkfd: Track unified memory when switching xnack mode
drm/amdgpu: Enable sram on vcn_4_0_2
drm/amdgpu: Enable VCN DPG for GC11_0_1
drm/msm: Fix build break with recent mm tree
drm/panel: simple: Use dev_err_probe() to simplify code
drm/panel: panel-edp: Use dev_err_probe() to simplify code
drm/panel: simple: Add Multi-Inno Technology MI0800FT-9
dt-bindings: display: simple: Add Multi-Inno Technology MI0800FT-9 panel
drm/amdgpu: correct the memcpy size for ip discovery firmware
drm/amdgpu: Skip put_reset_domain if it doesn't exist
drm/amdgpu: remove switch from amdgpu_gmc_noretry_set
drm/amdgpu: Fix mc_umc_status used uninitialized warning
drm/amd/display: Prevent OTG shutdown during PSR SU
drm/amdgpu: add page retirement handling for CPU RAS
drm/amdgpu: use RAS error address convert api in mca notifier
drm/amdgpu: support to convert dedicated umc mca address
drm/amdgpu: export umc error address convert interface
drm/amdgpu: fix sdma v4 init microcode error
drm/amd/display: fix array-bounds error in dc_stream_remove_writeback()
...
fixes all over the tree. Other subsystems depending on this change
have been asked to pull an immutable topic branch for this.
* new driver for Microchip PCI1xxxx switch
* heavy refactoring of the Mellanox BlueField driver
* we prefer async probe in the i801 driver now
* the rest is usual driver updates (support for more SoCs, some
refactoring, some feature additions)
-----BEGIN PGP SIGNATURE-----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=arni
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- 'remove' callback converted to return void. Big change with trivial
fixes all over the tree. Other subsystems depending on this change
have been asked to pull an immutable topic branch for this.
- new driver for Microchip PCI1xxxx switch
- heavy refactoring of the Mellanox BlueField driver
- we prefer async probe in the i801 driver now
- the rest is usual driver updates (support for more SoCs, some
refactoring, some feature additions)
* tag 'i2c-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (37 commits)
i2c: pci1xxxx: prevent signed integer overflow
i2c: acpi: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
i2c: i801: Prefer async probe
i2c: designware-pci: Use standard pattern for memory allocation
i2c: designware-pci: Group AMD NAVI quirk parts together
i2c: microchip: pci1xxxx: Add driver for I2C host controller in multifunction endpoint of pci1xxxx switch
docs: i2c: slave-interface: return errno when handle I2C_SLAVE_WRITE_REQUESTED
i2c: mlxbf: remove device tree support
i2c: mlxbf: support BlueField-3 SoC
i2c: cadence: Add standard bus recovery support
i2c: mlxbf: add multi slave functionality
i2c: mlxbf: support lock mechanism
macintosh/ams: Adapt declaration of ams_i2c_remove() to earlier change
i2c: riic: Use devm_platform_ioremap_resource()
i2c: mlxbf: remove IRQF_ONESHOT
dt-bindings: i2c: rockchip: add rockchip,rk3128-i2c
dt-bindings: i2c: renesas,rcar-i2c: Add r8a779g0 support
i2c: tegra: Add GPCDMA support
i2c: scmi: Convert to be a platform driver
i2c: rk3x: Add rv1126 support
...
This reverts commit 211f276ed3.
For quite some time, core DRM helpers already ensure that any relevant
connectors/CRTCs/etc. are disabled, as well as their associated
components (e.g., bridges) when suspending the system. Thus,
analogix_dp_bridge_{enable,disable}() already get called, which in turn
call drm_panel_{prepare,unprepare}(). This makes these drm_panel_*()
calls redundant.
Besides redundancy, there are a few problems with this handling:
(1) drm_panel_{prepare,unprepare}() are *not* reference-counted APIs and
are not in general designed to be handled by multiple callers --
although some panel drivers have a coarse 'prepared' flag that mitigates
some damage, at least. So at a minimum this is redundant and confusing,
but in some cases, this could be actively harmful.
(2) The error-handling is a bit non-standard. We ignored errors in
suspend(), but handled errors in resume(). And recently, people noticed
that the clk handling is unbalanced in error paths, and getting *that*
right is not actually trivial, given the current way errors are mostly
ignored.
(3) In the particular way analogix_dp_{suspend,resume}() get used (e.g.,
in rockchip_dp_*(), as a late/early callback), we don't necessarily have
a proper PM relationship between the DP/bridge device and the panel
device. So while the DP bridge gets resumed, the panel's parent device
(e.g., platform_device) may still be suspended, and so any prepare()
calls may fail.
So remove the superfluous, possibly-harmful suspend()/resume() handling
of panel state.
Fixes: 211f276ed3 ("drm: bridge: analogix/dp: add panel prepare/unprepare in suspend/resume time")
Link: https://lore.kernel.org/all/Yv2CPBD3Picg%2FgVe@google.com/
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220822180729.1.I8ac5abe3a4c1c6fd5c061686c6e883c22f69022c@changeid
Some panels trigger HPD irq due to noise, the HPD debounce
may be 1.8ms, exceeding the default irq detect window, ~1.4ms.
This patch set HPD irq detection window to 2ms to
tolerate the HPD noise.
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220903130833.541463-1-xji@analogixsemi.com
1. Support HDMI_I2S audio format.
2. Return 0 if there is no sink connection in .hw_param callback.
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Acked-by: Hsin-Yi Wang <hsinyi@chromium.org>
Acked-by: Jiaxin Yu<jiaxin.yu@mediatek.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220726033058.403715-1-xji@analogixsemi.com
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In anx7625_parse_dt(), 'pdata->mipi_host_node' will be assigned a
new reference with of_graph_get_remote_node() which will increase
the refcount of the object, correspondingly, we should call
of_node_put() for the old reference stored in the 'pdata->mipi_host_node'.
Fixes: 8bdfc5dae4 ("drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP")
Signed-off-by: Liang He <windhl@126.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220719065447.1080817-1-windhl@126.com
Move hpd polling check into wait_hpd_asserted() callback. For the cases
that aux transfer function wasn't used, do hpd polling check after pm
runtime resume, which will power on the bridge.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220706125254.2474095-5-hsinyi@chromium.org
Move devm_of_dp_aux_populate_ep_devices() after pm runtime and i2c setup
to avoid NULL pointer crash.
edp-panel probe (generic_edp_panel_probe) calls pm_runtime_get_sync() to
read EDID. At this time, bridge should have pm runtime enabled and i2c
clients ready.
Fixes: adca62ec37 ("drm/bridge: anx7625: Support reading edid through aux channel")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220706125254.2474095-4-hsinyi@chromium.org
There's no need to check for IRQ or disable it in suspend.
Use pm_runtime_force_suspend(resume) to make sure anx7625 is powered off
correctly. Make the system suspend/resume and pm runtime suspend/resume
more consistent.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220706125254.2474095-3-hsinyi@chromium.org
drm_crtc.h has no need for drm_edid.h, so don't include it.
Avoids useless rebuilds of the entire universe when
touching drm_edid.h.
Quite a few placs do currently depend on drm_edid.h without
actually including it directly. All of those need to be fixed
up.
v2: Fix up i915 and msm some more
v3: Fix alphabetical ordering (Sam)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220614090245.30283-1-ville.syrjala@linux.intel.com
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
As V4L2_FWNODE_BUS_TYPE_PARALLEL not properly descript for DPI
interface, this patch use new defined V4L2_FWNODE_BUS_TYPE_DPI for it.
Fixes: fd0310b6fe ("drm/bridge: anx7625: add MIPI DPI input feature")
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220422084720.959271-4-xji@analogixsemi.com
While parsing the DT, the anx7625 driver checks for the presence of a
panel bridge on endpoint 1. If it is missing, pdata->panel_bridge stores
the error pointer and the function returns successfully without first
cleaning that variable. This is an issue since other functions later
check for the presence of a panel bridge by testing the trueness of that
variable.
In order to ensure proper behavior, zero out pdata->panel_bridge before
returning when no panel bridge is found.
Fixes: 9e82ea0fb1 ("drm/bridge: anx7625: switch to devm_drm_of_get_bridge")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220613163705.1531721-1-nfraprado@collabora.com
Convert driver to use this new helper to standardize
OF "data-lanes" parsing.
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Xin Ji <xji@analogixsemi.com>
To: dri-devel@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20220524010522.528569-2-marex@denx.de
Most eDP panel functions only work correctly when the panel is not in
self-refresh. In particular, analogix_dp_bridge_disable() tends to hit
AUX channel errors if the panel is in self-refresh.
Given the above, it appears that so far, this driver assumes that we are
never in self-refresh when it comes time to fully disable the bridge.
Prior to commit 846c7dfc11 ("drm/atomic: Try to preserve the crtc
enabled state in drm_atomic_remove_fb, v2."), this tended to be true,
because we would automatically disable the pipe when framebuffers were
removed, and so we'd typically disable the bridge shortly after the last
display activity.
However, that is not guaranteed: an idle (self-refresh) display pipe may
be disabled, e.g., when switching CRTCs. We need to exit PSR first.
Stable notes: this is definitely a bugfix, and the bug has likely
existed in some form for quite a while. It may predate the "PSR helpers"
refactor, but the code looked very different before that, and it's
probably not worth rewriting the fix.
Cc: <stable@vger.kernel.org>
Fixes: 6c836d965b ("drm/rockchip: Use the helpers for PSR")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228122522.v2.1.I161904be17ba14526f78536ccd78b85818449b51@changeid
This reverts commit a77c2af099.
This patch depends on the patches just aplied to the media tree, and will
not build without them, which leaves drm-misc-next in a broken state.
Let's revert the two latter patches until rc1 has been branched,
and rc1 has been backmerged into drm-misc-next.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220523161520.354687-1-robert.foss@linaro.org
Add of_node_put call on the endpoint node after it is not needed.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Xin Ji <xji@analogixsemi.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220519112337.62198-1-marex@denx.de
As V4L2_FWNODE_BUS_TYPE_PARALLEL not properly descript for DPI
interface, this patch use new defined V4L2_FWNODE_BUS_TYPE_DPI for it.
Fixes: fd0310b6fe ("drm/bridge: anx7625: add MIPI DPI input feature")
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220422084720.959271-4-xji@analogixsemi.com
Move DRM's HDCP helper library into the display/ subdirectory and add
it to DRM's display helpers. Split the header file into core and helpers.
Update all affected drivers. No functional changes.
v3:
* fix Kconfig dependencies
v2:
* fix include statements (Jani, Javier)
* update Kconfig symbols
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-7-tzimmermann@suse.de
Replace the DP-helper module with a display-helper module. The
support for DisplayPort becomes an internal option that drivers
have to select. Update all related Kconfig and Makefile rules.
Besides the existing code for DisplayPort, the new module will
contain helpers for other video-output standards, such as HDMI.
Drivers will have to select their required video-output helpers.
Linking all display-related code into a single module avoids the
proliferation of small kernel modules.
The module parameters drm_dp_cec_unregister_delay, dp_aux_i2c_speed_khz,
and dp_aux_i2c_transfer_size are moving from the drm_dp_helper namespace
to drm_display_helper.
v2:
* mention module parameters in commit message (Javier)
* distiguish between display module and DP support in Kconfig
* update Makefile rules for DP helpers
* move Kconfig rules into separate file under display/
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-4-tzimmermann@suse.de
Rename dp/ to display/ to account for additional display-related
helpers, such as HDMI. Update all related include statements. No
functional changes.
Various drivers, such as i915 and amdgpu, use similar naming scheme
by putting code for video-output standards into a local display/
directory. The new directory's name is aligned with this convention.
v2:
* update commit message (Javier)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-3-tzimmermann@suse.de
In the error handling path, the clk_prepare_enable() function
call should be balanced by a corresponding 'clk_disable_unprepare()'
call, as already done in the remove function.
Fixes: 3424e3a4f8 ("drm: bridge: analogix/dp: split exynos dp driver to bridge directory")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220420011644.25730-1-linmq006@gmail.com
As defined in the anx7625 dt-binding, the analogix,lane0-swing and
analogix,lane1-swing properties are uint8 arrays. Yet, the driver was
reading the array as if it were of uint32 and masking to 8-bit before
writing to the registers. This means that a devicetree written in
accordance to the dt-binding would have its values incorrectly parsed.
Fix the issue by reading the array as uint8 and storing them as uint8
internally, so that we can also drop the masking when writing the
registers.
Fixes: fd0310b6fe ("drm/bridge: anx7625: add MIPI DPI input feature")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220408013034.673418-1-nfraprado@collabora.com
Speaker may share I2S with DP and .get_eld callback will be called when
speaker is playing. When HDMI wans't connected, the connector will be
null. Instead of return an error, fill in empty ELD.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414090003.1806535-1-hsinyi@chromium.org
Add the missing destroy_workqueue() before return from
anx7625_i2c_probe() in the error handling case.
Fixes: adca62ec37 ("drm/bridge: anx7625: Support reading edid through aux channel")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220326073326.3389347-1-yangyingliang@huawei.com
As downstream sink was set into standby mode while bridge disabled,
this patch used for setting downstream sink into normal status
while enable bridge.
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Reviewed-by: Pin-Yen Lin <treapking@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220322080213.1487134-1-xji@analogixsemi.com
DP AUX transactions can consist of many short operations. There's no
need to power things up/down in short intervals.
I pick an arbitrary 100ms; for the systems I'm testing (Rockchip
RK3399), runtime-PM transitions only take a few microseconds.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220301181107.v4.2.I48b18ab197c9b649d376cf8cfd934e59d338f86d@changeid
If the display is not enable()d, then we aren't holding a runtime PM
reference here. Thus, it's easy to accidentally cause a hang, if user
space is poking around at /dev/drm_dp_aux0 at the "wrong" time.
Let's get a runtime PM reference, and check that we "see" the panel.
Don't force any panel power-up, etc., because that can be intrusive, and
that's not what other drivers do (see
drivers/gpu/drm/bridge/ti-sn65dsi86.c and
drivers/gpu/drm/bridge/parade-ps8640.c.)
Fixes: 0d97ad03f4 ("drm/bridge: analogix_dp: Remove duplicated code")
Cc: <stable@vger.kernel.org>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220301181107.v4.1.I773a08785666ebb236917b0c8e6c05e3de471e75@changeid
The function "drm_of_find_panel_or_bridge" has been deprecated in
favor of "devm_drm_of_get_bridge".
Switch to the new function and reduce boilerplate.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221072835.10032-1-jose.exposito89@gmail.com
Clang static analysis reports this issue
anx7625.c:876:13: warning: The left operand of '&' is
a garbage value
if (!(bcap & 0xOA01)) {
~~~~ ^
bcap is only set by a successful call to
anx7625_aux_trans(). So check.
Fixes: cd1637c7e4 ("drm/bridge: anx7625: add HDCP support")
Signed-off-by: Tom Rix <trix@redhat.com>
Fixes: adca62ec37 ("drm/bridge: anx7625: Support reading edid through aux channel")
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220303201943.501746-1-trix@redhat.com
Reviewed-by: Robert Foss <robert.foss@linaro.org>
This device requires the packets on lanes aligned at the end to fix
screen shift or scroll.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220309073637.3591-4-rex-bc.chen@mediatek.com
If the previous transfer didn't end with a command without DP_AUX_I2C_MOT,
the next read trasnfer will miss the first byte. But if the command in
previous transfer is requested with length 0, it's a no-op to anx7625
since it can't process this command. anx7625 requires the last command
to be read command with length > 0.
It's observed that if we clear the DP_AUX_I2C_MOT in read transfer, we
can still get correct data. Clear the read commands with DP_AUX_I2C_MOT
bit to fix this issue.
Fixes: adca62ec37 ("drm/bridge: anx7625: Support reading edid through aux channel")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220217082224.1823916-1-hsinyi@chromium.org
The length of EDID block can be longer than 256 bytes, so we should use
`int` instead of `u8` for the `edid_pos` variable.
Fixes: 8bdfc5dae4 ("drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP")
Signed-off-by: Pin-Yen Lin <treapking@chromium.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220210103827.402436-1-treapking@chromium.org
Support reading edid through aux channel if panel is connected to aux
bus. Extend anx7625_aux_dpcd_trans() to implement aux transfer function:
1. panel is populated in devm_of_dp_aux_populate_ep_devices(), so move
anx7625_parse_dt() after.
2. Use pm runtime autosuspend since aux transfer function is called
multiple times when reading edid.
3. No-op if aux transfer length is 0.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220213103437.3363848-3-hsinyi@chromium.org
Send DPCD command to downstream before anx7625 power down,
let downstream monitor enter into standby mode.
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220213103437.3363848-1-hsinyi@chromium.org
It will connect to the mipi dsi host and find the corresponding
mipi dsi host node, but the node registered by the mipi dsi host
has not been loaded yet. of_find_mipi_dsi_host_by_node() returns -EINVAL
which causes the calling driver to fail.
If the anx7625 driver is loaded afterwards the driver requesting
the mipi dsi host will not notice this.
Better approach is to return -EPROBE_DEFER in such case.
Then when the anx7625 driver appears the driver requesting
the mipi dsi host will be probed again.
Signed-off-by: owen <qwt9588@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220117100949.9542-1-qwt9588@gamil.com
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Move DisplayPort functions into a separate module to reduce the size
of the KMS helpers. Select DRM_DP_HELPER for all users of the code. To
avoid naming conflicts, rename drm_dp_helper.c to drm_dp.c
This change can help to reduce the size of the kernel binary. Some
numbers from a x86-64 test build:
Before:
drm_kms_helper.ko: 447480 bytes
After:
drm_dp_helper.ko: 216632 bytes
drm_kms_helper.ko: 239424 bytes
For early-boot graphics, generic DRM drivers, such as simpledrm,
require DRM KMS helpers to be built into the kernel. Generic helper
functions for DisplayPort take up a significant portion of DRM KMS
helper library. These functions are not used by generic drivers and
can be loaded as a module.
v3:
* fix include statement in DRM selftests
v2:
* move DP helper code into dp/ (Jani)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220114114535.29157-4-tzimmermann@suse.de
This patch provides HDCP setting interface for userspace to dynamic
enable/disable HDCP function.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220106100127.1862702-2-xji@analogixsemi.com
Since i2c_new_client_device() function return error pointers.
The i2c_new_dummy_device() function does not return NULL, It returns error
pointers too. Using IS_ERR() to check the return value to fix this.
Fixes: 8bdfc5dae4e3("drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211222083350.18514-1-linmq006@gmail.com
Reviewed-by: Robert Foss <robert.foss@linaro.org>
As GPIO probe function "devm_gpiod_get_optional()" may return error
code, driver should identify GPIO desc as NULL to avoid crash.
Acked-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211119015804.3824027-1-xji@analogixsemi.com
Reviewed-by: Robert Foss <robert.foss@linaro.org>
