[WHY]
DSC block level should only be responsible for reporting single DSC
instance capabilities. Factoring in ODM combine requirements should be
handled in dc_dsc.c. Both components should acquire clocks from clk_mgr
to determine throughput capabilities instead of relying on hard coded
values as these can differ by SoC and SKU.
[HOW]
1) Add dsc_get_single_enc_caps to acquire single DSC instance
capabilities (replacing dsc_get_enc_caps), factoring in DSCCLK
2) add build_dsc_enc_caps to combine single DSC instance capabilities
3) account for max pixel rate per pipe (DISPCLK) when calculating
minimum slice count
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Expose dcn401_initialize_min_clocks() for future use and add additional
check for IP register.
Reviewed-by: Nevenko Stupar <nevenko.stupar@amd.com>
Signed-off-by: Karthi Kandasamy <karthi.kandasamy@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When booting without an HDMI display connected, the I2C registers
are not initialized correctly, leading to DC_I2C_ARBITRATION register
getting stuck with DC_I2C_REG_RW_CNTL_STATUS == USED_BY_SW.
[How]
* Correct TOCTOU race condition in engine acquire logic which did not
check against DMUB trying to acquire it at the same time.
* Deassert SOFT_RESET before acquire, as it can block access to other
I2C registers.
* Add a workaround in release, checking that after triggerring
DC_I2C_SW_DONE_USING_I2C_REG, DC_I2C_REG_RW_CNTL_STATUS != USED_BY_SW.
If necessary, trigger DC_I2C_SW_DONE_USING_I2C_REG again.
* Remove unnecessary clear of DC_I2C_SW_USE_I2C_REG_REQ, which engine
ignores according to specification.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Dominik Kaszewski <dominik.kaszewski@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Common resolutions are added to supported modes to enable compatibility
scenarios that compositors may use to do things like clone displays. There
is no guarantee however that the panel will natively support these modes.
[How]
If the compositor hasn't enabled scaling but a non-native resolution has
been picked for an LVDS panel turn the scaler on anyway. This will ensure
compatibility.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Common modes are added to LVDS for compatibility in clone mode, but
not all panels support them. Non-native modes were disabled in the past
but this caused problems because compositors didn't use scaling for non
native modes. Now non-native modes on LVDS will enable the scaler by
default.
[How]
Check the connector type. If the connector is LVDS avoid adding common
modes.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
OLED panels can be fully off, but this behavior is unexpected.
[How]
Ensure that minimum luminance is at least 1.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4338
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 51496c7737)
[WHY]
Rounding error sometimes occurs when the refresh rate is equal to a panel's
max refresh rate, causing HDMI compliance failures.
[HOW]
Added a case so that we round up to avoid v_total_min to be below a panel's
minimum bound.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Harold Sun <Harold.Sun@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit fe7645d22b)
[WHY]
On DCN314, using full screen application with enabled scaling like 150%,
175%, with overlay cursor, causes a second cursor to appear when changing
planes. Dpp cache is used to track the HW cursor enable. Since power gate
is disabled for hubp & dpp in DCN314, dpp_reset() zero'ed the dpp struct,
while the dpp hardware was not power gated.
So, when plane is changed in a full screen app, and the overlay cursor is
enabled, the cache is cleared, so the cache does not represent the actual
cursor state.
[HOW]
Added conditionals for dpp & hubp reset and their pg_control functions
only if according power_gate flags are enabled.
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Signed-off-by: Ivan Lipski <ivlipski@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When performing certain link maintenance compliance tests or forcing link
settings, changing between 128b/132b and 8b/10b rates no longer works on
some ASICs. Some rate divider updates only occur when we set
timings or validate state, which is not performed currently when toggling
DPMS to change rates.
[HOW]
Re-calculate dividers and reprogram audio when switching between DIO
and HPO through DP compliance/escape code path.
Add OTG disable/re-enable so we don't touch the clock while OTG is active.
Acquire dcLock before forcing link settings to avoid thread synchronization
errors due to added programming in escape code path and potential HPD
interrupts.
Reviewed-by: George Shen <george.shen@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Mike Katsnelson <mike.katsnelson@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
OLED panels can be fully off, but this behavior is unexpected.
[How]
Ensure that minimum luminance is at least 1.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4338
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Rounding error sometimes occurs when the refresh rate is equal to a panel's
max refresh rate, causing HDMI compliance failures.
[HOW]
Added a case so that we round up to avoid v_total_min to be below a panel's
minimum bound.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Harold Sun <Harold.Sun@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
Separate the checks for set_gsl and set_gsl_source_select, since
source_select may not be implemented/necessary.
Reviewed-by: Nevenko Stupar <nevenko.stupar@amd.com>
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
- Consolidated the initialization of DML21 parameters into a single
function `dml21_populate_dml_init_params` to streamline the process
and improve code readability.
- Updated the function signatures in the header files to reflect changes
in parameter passing for DML context.
- Removed redundant debug option handling and integrated it into the new
configuration population function.
- Adjusted the DML21 initialization logic in the wrapper to accommodate
the new structure, ensuring compatibility with different DCN versions.
- Enhanced the handling of clock parameters and bounding box configurations
from various sources, including hardware defaults and software policies.
- Improved the clarity of the code by renaming functions and variables for
better understanding of their purposes.
Reviewed-by: Austin Zheng <austin.zheng@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Expose some function for new platform use
Reviewed-by: Nevenko Stupar <nevenko.stupar@amd.com>
Signed-off-by: Karthi Kandasamy <karthi.kandasamy@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The tunnel BW validation code has changed to the new one.
Remove the unused code.
The DP tunneling overhead is not updated in SST.
Move updating DP tunneling overhead for both SST and MST.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Prevents null pointer dereferences to enhance function robustness
[HOW]
Adds early null check and return false if invalid.
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When EDID is retrieved via drm_edid_raw(), it doesn't guarantee to
return proper EDID bytes the caller wants: it may be either NULL (that
leads to an Oops) or with too long bytes over the fixed size raw_edid
array (that may lead to memory corruption). The latter was reported
actually when connected with a bad adapter.
Add sanity checks for drm_edid_raw() to address the above corner
cases, and return EDID_BAD_INPUT accordingly.
Fixes: 48edb2a425 ("drm/amd/display: switch amdgpu_dm_connector to use struct drm_edid")
Link: https://bugzilla.suse.com/show_bug.cgi?id=1236415
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 648d3f4d20)
Cc: stable@vger.kernel.org
[Why]
commit 16dc8bc27c ("drm/amd/display: Export full brightness range to
userspace") adjusted the brightness range to scale to larger values, but
missed updating AMDGPU_MAX_BL_LEVEL which is needed to make sure that
scaling works properly with custom brightness curves.
[How]
As the change for max brightness of 0xFFFF only applies to devices
supporting DC, use existing DC define MAX_BACKLIGHT_LEVEL.
Fixes: 16dc8bc27c ("drm/amd/display: Export full brightness range to userspace")
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20250623171114.1156451-1-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 5b852044eb)
Cc: stable@vger.kernel.org
When EDID is retrieved via drm_edid_raw(), it doesn't guarantee to
return proper EDID bytes the caller wants: it may be either NULL (that
leads to an Oops) or with too long bytes over the fixed size raw_edid
array (that may lead to memory corruption). The latter was reported
actually when connected with a bad adapter.
Add sanity checks for drm_edid_raw() to address the above corner
cases, and return EDID_BAD_INPUT accordingly.
Fixes: 48edb2a425 ("drm/amd/display: switch amdgpu_dm_connector to use struct drm_edid")
Link: https://bugzilla.suse.com/show_bug.cgi?id=1236415
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Brightness programming may involve a conversion of a user requested
brightness against what was in a custom brightness curve. The values
might not match what a user programmed.
[How]
Add a new trace event to show specific converted brightness values.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Link: https://lore.kernel.org/r/20250623171114.1156451-2-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
commit 16dc8bc27c ("drm/amd/display: Export full brightness range to
userspace") adjusted the brightness range to scale to larger values, but
missed updating AMDGPU_MAX_BL_LEVEL which is needed to make sure that
scaling works properly with custom brightness curves.
[How]
As the change for max brightness of 0xFFFF only applies to devices
supporting DC, use existing DC define MAX_BACKLIGHT_LEVEL.
Fixes: 16dc8bc27c ("drm/amd/display: Export full brightness range to userspace")
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20250623171114.1156451-1-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add the number of horizontal slices argument to allow configuring clock
based on slice number.
Reviewed-by: Nevenko Stupar <nevenko.stupar@amd.com>
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update logging macros for detailed debugging
Update structs to contain more detailed information
Add HDMI 16 and 20 Gbps rates
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It is normal to prune resolutions that exceed hw or bw limitation.
Use error oriented wordings could cause misunderstanding.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver should be able to send LSDMA commands to DMCUB
[How]
Driver can now send LSDMA commands to DMCUB.
DMCUB should process them and send to LSDMA controller.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Ostrowski Rafal <rostrows@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Found that we add redundant macro on refresh rate when calculating vtotal,
so we remove it.
Reviewed-by: Robin Chen <robin.chen@amd.com>
Signed-off-by: Weiguang Li <wei-guang.li@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DCN35 is having “DC: failed to blank crtc!” when running HPO
test cases. It's caused by not having sufficient udelay time.
[how]
Replace the old wait_for_blank_complete function with fsleep function to
sleep just until the next frame should come up. This way it doesn't poll
in case the pixel clock or other clock was bugged or until vactive and
the vblank are hit again.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Wen Chen <Wen.Chen3@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
mode_select was supposed to be initialized in mpc_read_gamut_remap but
is not set in default case. This can cause indeterminate
behaviors.
This is reported as an UNINIT error by Coverity.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add new function for DP tunnel bandwidth validation.
It uses the estimated BW and allocated BW to validate the timings.
Reviewed-by: PeiChen Huang <peichen.huang@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Pixel data bandwidth required in mode programming (MP) ends up being
higher than what was calculated in mode support (MS) even though
the prefetch bandwidths calculated in MP are lower than the MS ones.
MP used a different equ prefetch schedule than MS which lead a
slight difference in parameters. This resulted in the pixel data
bandwidth in MP to be higher than MS.
[How]
Rename the RequiredPrefetchBWOTO term so it can be applied generically.
Update the value with the EQU bandwidth if the EQU schedule is used.
Get the max prefetch bandwidth that MS calculated and use it
as part of the calculations for required bandwidth.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need the driver-core fixes that are in 6.16-rc3 into here as well
to build on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[WHAT]
hws was checked for null earlier in dce110_blank_stream, indicating hws
can be null, and should be checked whenever it is used.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 79db43611f)
Cc: stable@vger.kernel.org
[WHY]
Userspace currently is offered a range from 0-0xFF but the PWM is
programmed from 0-0xFFFF. This can be limiting to some software
that wants to apply greater granularity.
[HOW]
Convert internally to firmware values only when mapping custom
brightness curves because these are in 0-0xFF range. Advertise full
PWM range to userspace.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 8dbd72cb79)
Cc: stable@vger.kernel.org
[WHY]
Backlight caps are read already in amdgpu_dm_update_backlight_caps().
They may be updated by update_connector_ext_caps(). Reading again when
registering backlight device may cause wrong values to be used.
[HOW]
Use backlight caps already registered to the dm.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 148144f6d2)
Cc: stable@vger.kernel.org
[WHAT]
Severe video playback corruption is observed in the following setup:
weston 14.0.90 (built from source) + mpv v0.40.0 with command:
mpv bbb_sunflower_1080p_60fps_normal.mp4 --vo=gpu
[HOW]
ABGR16161616 needs to be included in dml2/2.1 translation.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Austin Zheng <austin.zheng@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit d023de809f)
Cc: stable@vger.kernel.org
[WHY]
For non-zero DSC instances it's possible that the HUBP domain required
to drive it for sequential ONO ASICs isn't met, potentially causing
the logic to the tile to enter an undefined state leading to a system
hang.
[HOW]
Add more checks to ensure that the HUBP domain matching the DSC instance
is appropriately powered.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit da63df0711)
Cc: stable@vger.kernel.org
[WHY]
These fields are read for the explicit purpose of detecting embedded LTTPRs
(i.e. between host ASIC and the user-facing port), and thus need to
calculate the correct DPCD address offset based on LTTPR count to target
the appropriate LTTPR's DPCD register space with these queries.
[HOW]
Cascaded LTTPRs in a link each snoop and increment LTTPR count when queried
via DPCD read, so an LTTPR embedded in a source device (e.g. USB4 port on a
laptop) will always be addressible using the max LTTPR count seen by the
host. Therefore we simply need to use a recently added helper function to
calculate the correct DPCD address to target potentially embedded LTTPRs
based on the received LTTPR count.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 791897f5c7)
Cc: stable@vger.kernel.org
[WHAT]
1. add dc cap for dp tunneling
2. add function to get index of host router
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 29e178d139)
Cc: stable@vger.kernel.org
DC v3.2.338 summary:
* DML bug fixes
* Add pwait to DMCUB hang reporting
* New definitions / changes to prep for new platforms.
* Misc cleanups
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The functions in this commit are defined for dpp401 but never used.
Removing them as they are not necessary.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Ryan Seto <ryanseto@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
some new asics will have an APG instance taking over certain functions.
Reviewed-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Expose some functions for new platform use
Reviewed-by: Nevenko Stupar <nevenko.stupar@amd.com>
Signed-off-by: Karthi Kandasamy <karthi.kandasamy@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To know if the firmware is idle when logging.
[How]
Add the pwait status to the DMCUB diagnostics.
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
hws was checked for null earlier in dce110_blank_stream, indicating hws
can be null, and should be checked whenever it is used.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Common modes are added to eDP for compatibility in clone mode, but
not all panels support them. Non-native modes were disabled in the past
but this caused problems because compositors didn't use scaling for non
native modes. Now non-native modes on eDP will enable the scaler by
default.
[How]
Check the connector type. If the connector is eDP avoid adding common
modes.
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Common resolutions are added to supported modes to enable compatibility
scenarios that compositors may use to do things like clone displays. There
is no guarantee however that the panel will natively support these modes.
[How]
If the compositor hasn't enabled scaling but a non-native resolution has
been picked for an eDP panel turn the scaler on anyway. This will ensure
compatibility.
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DML2 (not DML2.1), DCN35 and DCN351 have the
default value for use_native_pstate_optimization
set to true. The code path where this bit is
false is not used.
[How]
Remove the bit and the corresponding code path
when it is set to false.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Yan Li <yan.li@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DML2, the current method to determine a
mode is supported involves checking the
voltage levels sequentially from the lowest,
until one is found that can support the
mode. It causes cursor lag due to low
performance.
[How]
We apply two methods for mode validation.
1) DC_VALIDATE_MODE_ONLY: only the
maximum voltage level is checked to
determine whether the mode is supported, which
improves performance and eliminate cursor lag.
2) DC_VALIDATE_MODE_AND_STATE_INDEX: when
the optimal voltage level is required, check
the voltage level from the lowest until
a suitable one is found found and returns
its index.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Yan Li <yan.li@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch addresses inconsistencies in the annotations for the
following functions:
- **dc_get_power_profile_for_dc_state**: Standardized parameter and
return value annotations.
- **dc_get_det_buffer_size_from_state**: Clarified parameter
documentation for better understanding.
- **dc_get_host_router_index**: Corrected parameter descriptions to
follow documentation conventions.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:6386: warning: Cannot understand ***************
Cc: Tom Chung <chiahsuan.chung@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Alex Hung <alex.hung@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When the suspend sequence has been aborted after prepare() but
before suspend() the resume() callback never gets called. The PM core
will call complete() when this happens. As the state has been cached
in prepare() it needs to be destroyed in complete() if it's still around.
[How]
Create a helper for destroying cached state and call it both in resume()
and complete() callbacks. If resume has been called the state will be
destroyed and it's a no-op for complete(). If resume hasn't been called
(such as an aborted suspend) then destroy the state in complete().
Fixes: 50e0bae34f ("drm/amd/display: Add and use new dm_prepare_suspend() callback")
Reviewed-by: Alex Hung <alex.hung@amd.com>
Link: https://lore.kernel.org/r/20250602014432.3538345-4-superm1@kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If drm_atomic_helper_suspend() has failed for any reason, it's stored
in adev->dm.cached_state. This isn't expected because the resume
(or complete()) sequence will attempt to use the stored state to
resume.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Link: https://lore.kernel.org/r/20250602014432.3538345-3-superm1@kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Fix kernel docs for new struct members
- Export full brightness range to userspace
- Only read ACPI backlight caps once
- Fix RMCM programming seq errors
- Add RMCM debug logging
- DML2.1 changes
- Fix mpv playback corruption on weston
- Adjust dto fix coverage
- Add option to disable PHY SSC reduction on transmitter enable
- Don't disable dtb as dto src during dpms off
- Add custom segmentation support
- Deprecate Loading Bounding Box From DMUB On DCN4
- Update tmz_surface type to match register
- Clear DPP 3DLUT Cap
- Add more checks for DSC / HUBP ONO guarantees
- Refactor DML2 DC power instance
- Remove dml/dcn401 files and references
- Get LTTPR IEEE OUI/Device ID From Closest LTTPR To Host
- Add HW change required mpc gamut remap
- Add DPIA debug option for zero allocation patch
- Add dc cap for dp tunneling
- Remove dpia debug bits
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
Add kernel-doc for new struct members for lut3d_caps and mpc_funcs.
This fixes the follow warnings from "make htmldocs".
./drivers/gpu/drm/amd/display/dc/inc/hw/mpc.h:1106: warning: Function
parameter or struct member 'mcm' not described in 'mpc_funcs'
./drivers/gpu/drm/amd/display/dc/inc/hw/mpc.h:1106: warning: Function
parameter or struct member 'rmcm' not described in 'mpc_funcs'
./drivers/gpu/drm/amd/display/dc/dc.h:249: warning: Function parameter
or struct member 'mcm_3d_lut_caps' not described in 'mpc_color_caps'
./drivers/gpu/drm/amd/display/dc/dc.h:249: warning: Function parameter
or struct member 'rmcm_3d_lut_caps' not described in 'mpc_color_caps'
./drivers/gpu/drm/amd/display/dc/dc.h:249: warning: Function parameter
or struct member 'preblend' not described in 'mpc_color_caps'
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Userspace currently is offered a range from 0-0xFF but the PWM is
programmed from 0-0xFFFF. This can be limiting to some software
that wants to apply greater granularity.
[HOW]
Convert internally to firmware values only when mapping custom
brightness curves because these are in 0-0xFF range. Advertise full
PWM range to userspace.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Backlight caps are read already in amdgpu_dm_update_backlight_caps().
They may be updated by update_connector_ext_caps(). Reading again when
registering backlight device may cause wrong values to be used.
[HOW]
Use backlight caps already registered to the dm.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
* Add a missing compilation unit
* Missing CFLAGS for certain units
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Severe video playback corruption is observed in the following setup:
weston 14.0.90 (built from source) + mpv v0.40.0 with command:
mpv bbb_sunflower_1080p_60fps_normal.mp4 --vo=gpu
[HOW]
ABGR16161616 needs to be included in dml2/2.1 translation.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Austin Zheng <austin.zheng@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Unnecessary to affect legacy APU's dto src sel during dpms behaviour
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Ausef Yousof <Ausef.Yousof@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
On some 8k display models flickering or black screens may occur at reduced
PHY SSC.
[HOW]
Add an option to set a workaround bit for these displays to keep the old
SSC value.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Muhammad Ahmed <Muhammad.Ahmed@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Adjusting otg dto programming in this path is unsafe otg may be en at
this time, swapping its src sel for example was discovered to cause
visual artifacts and was moved to dcn31_program_pix_clk (where otg is
guaranteed off) but dto functional clk enable bit is not cleared.
dcn31_program_pix_clk is called during dpms on, so until that point
we will have a otg with functional src sel set (Sel DTBclk) and that
functional clk dto en is unset (i.e DTB DTO EN), which is invalid and tg
will not function and system will hang on something such as flip
incoming from OS during dpms off. will scope out dcn315 as it was
affecting diags tests on certain CI machines (not crbs)
Reviewed-by: Leo Chen <leo.chen@amd.com>
Signed-off-by: Ausef Yousof <Ausef.Yousof@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Add support for uneven segmentation size
[HOW]
Currently width + x_start is automatically calculated using
slice index + dividing stream into equally sized segments.
Add override variables for dst_rect width and x
Reviewed-by: Samson Tam <samson.tam@amd.com>
Signed-off-by: Brendan Steve Leder <BrendanSteve.Leder@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
dml2_soc_bb struct can continuously receive updates for future ASICs.
Alignment issues may arise since VBIOS DMCUB contains an older version of
the SOC BB.
Populating the bounding box with values from DMCUB is no longer necessary
since values such as UCLK will be overridden by values acquired by PMFW
anyways.
[HOW]
Use bb_from_dmub to store DCN specific bounding box parameters in DMCUB.
Add helpers to translate DCN specific struct to the corresponding
dml2_soc_bb field.
To avoid alignment issues:
Deprecate applying DMCUB SoC BB for DCN4
For future projects:
Create a flattened struct containing all sensitive parameters in the
bounding box. New parameters can be added to the bottom of the new struct
as needed.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Update tmz_surface's type to match register size
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Clear DPP 3DLUT Cap flag on ASICs that do not use it
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Ryan Seto <ryanseto@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
For non-zero DSC instances it's possible that the HUBP domain required
to drive it for sequential ONO ASICs isn't met, potentially causing
the logic to the tile to enter an undefined state leading to a system
hang.
[HOW]
Add more checks to ensure that the HUBP domain matching the DSC instance
is appropriately powered.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Use a dedicated DC power option and instance pair.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
DCN401 is only supported using DML2.1, so remove unused code and files.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
These fields are read for the explicit purpose of detecting embedded LTTPRs
(i.e. between host ASIC and the user-facing port), and thus need to
calculate the correct DPCD address offset based on LTTPR count to target
the appropriate LTTPR's DPCD register space with these queries.
[HOW]
Cascaded LTTPRs in a link each snoop and increment LTTPR count when queried
via DPCD read, so an LTTPR embedded in a source device (e.g. USB4 port on a
laptop) will always be addressible using the max LTTPR count seen by the
host. Therefore we simply need to use a recently added helper function to
calculate the correct DPCD address to target potentially embedded LTTPRs
based on the received LTTPR count.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
The BW zero allocation patch is no longer required.
Add a debug option to enable it in case we encounter an issue.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
1. add dc cap for dp tunneling
2. add function to get index of host router
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Fix brightness relevant settings
- Fix calling blanking stream twice
- Extend dc mode validation types to support more scenarios
- Update DMCUB loading sequence for DCN3.5
Acked-by: ChiaHsuan Chung <chiahsuan.chung@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The boolean fast_validate is used as an
input parameter in multiple functions. To
support more scenarios, we are
replacing it with enum dc_validate_mode.
[How]
The enum dc_validate_mode introduces three
possible values:
1) DC_VALIDATE_MODE_AND_PROGRAMMING:
Apply the mode to hardware
2) DC_VALIDATE_MODE_ONLY:
Check whether the mode can be supported
3) DC_VALIDATE_MODE_AND_STATE_INDEX:
Check if the mode can be supported, and
determine the optimal voltage level
needed to support it.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Yan Li <yan.li@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
New sequence from HW for reset and firmware reloading has been
provided that aims to stabilize the reload sequence in the case the
firmware is hung or has outstanding requests.
[How]
Update the sequence to remove the DMUIF reset and the redundant
writes in the release.
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Fixes for DML21
- Support OLED SDR with AMD ABC
- Indirect buffer transport for FAMS2 commands
- Correct non-OLED pre_T11_delay
- Optime boot-up consuming time
- Add support for 2nd sharpening range
- Fix on chroma planes scaling
Acked-by: ChiaHsuan Chung <chiahsuan.chung@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add dmub command to support LSDMA
Acked-by: ChiaHsuan Chung <chiahsuan.chung@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Move vmalloc.h include code to header file.
Reviewed-by: ChiaHsuan Chung <chiahsuan.chung@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add support for 2nd sharpening range for cases where we want
override existing DCN sharpening range
Reviewed-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When doing 2:1 downscaling on a YUV sub-sampled format, the chroma
scaling ratio is 1:1. Since chroma has cositing, it is needed to do
scaling on the chroma plane(s) and not to bypass chroma scaling.
[How]
Do not set the chroma taps to one when the chroma ratio is identity
and the input format is a sub-sampled YUV format.
Reviewed-by: Samson Tam <samson.tam@amd.com>
Signed-off-by: Navid Assadian <Navid.Assadian@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DML needs a path for FAMS methods.
[How]
Apply instance of fams2_stream_sub_params_v2 structure with
a FAMS placeholder for DML.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Oleh Kuzhylnyi <okuzhyln@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In the case of an external monitor disconnection,
the kernel mode will attempt to post new timing
validation with two path counts (eDP + external
monitor removed to virtual).
[how]
Skip validating color depth and pixel encoding in the
scenario involving a DP to HDMI active converter dongle.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Jingwen Zhu <Jingwen.Zhu@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Observe that we try to access DPCD 0x600h of disconnected DP ports.
In order not to wasting time on retrying these ports, call
dpcd_write_rx_power_ctrl() after checking its connection status.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The `drm_*()` print macros will handle including the driver in the print
already. The extra print of the word `amdgpu` is unnecessary.
[How]
Modify all prints to drop `amdgpu: `.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The quantity and duration of FAMS2 commands are set to increase
in future products. This necessitates the implementation of a new
mechanism for chaining commands together, allowing all commands
to be processed within a single transaction.
[How]
The indirect buffer acts as a shared buffer on the driver side,
mapped to DMUB's internal CW7 address. Its source address and
size are sent through mailbox command to DMUB, triggering the
transaction.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Oleh Kuzhylnyi <okuzhyln@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Move only RMCM programming outside of dcn401. Extended HW
definition in dc for memory layout to extend support.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Yihan Zhu <Yihan.Zhu@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Nits programming for SDR panel is only supported by VESA ABC.
[How]
1. Loose nits programming for OLED SDR panel with AMD ABC.
2. We support two ABC methods. Disable one before we program the other
in case panel freaks out.
3. Update HDR judgement in setBR with a solider condition.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Signed-off-by: Camille Cho <Camille.Cho@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Store state related info inside mode_lib.
- Fix bad DCFCLK deep sleep
- Update FAMS structure in DMUB header
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
New enums need to be added to the end to avoid
back compat issues.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
