[Why]
SEC_CNTL isn't readable by x86 and can block Z8 entry if read.
[How]
Remove the read.
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add some scruct for secure display.
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Spread on DPREFCLK by 0.3 percent can have a negative effect on sink
when PHY SSC is also spread by 0.3 percent
[How]
Add boot option for DMU to lower PHY SSC
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Hansen Dsouza <Hansen.Dsouza@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A race condition occurs between cursor movement and vertical interrupt control
thread from OS, with both threads trying to exit IPS2.
Vertical interrupt control thread clears the prev driver allow signal while not fully
finishing the IPS2 exit process.
[How]
We want to detect all the allow signals have been cleared before we perform the full exit.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Leo Chen <leo.chen@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This enables starting and stopping IPS residency measurements
and querying the IPS residency information consisting of residency
percent, entry counter, total time active & inactive, and histograms
for the specified IPS mode.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Ovidiu Bunea <Ovidiu.Bunea@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We intend to consolidate dp tunneling and conventional dp link training.
[HOW]
1. Use the same link training entry for both dp and dpia
2. Move SET_CONFIG of non-transparent mode to dmub side
3. Add set_tps_notification dmub_cmd to notify tps request for
non-transparent dpia link training
4. Check dpcd request result and abort link training early if dpia
aux tunneling fails
5. Add option to avoid affect old product
6. Separately handle wait_time_microsec for dpia
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Reviewed-by: George Shen <george.shen@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to avoid arming the HPD timer in firmware when preparing for
S0i3 entry when DC is considered in D3.
[How]
Notify DMCUB of the power state transitions so it can decide to arm
the HPD timer for idle in DCN35 only in D0.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Ovidiu Bunea <Ovidiu.Bunea@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Drop coasting_vtotal_high and pad from dmub_cmd_update_dirty_rect_data,
since it is not used.
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The DP tunnel AUX reply is received through Outbox1. Print the Outbox1
status if an issue occurs.
Signed-off-by: Cruise <Cruise.Hung@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Visual Confirm would tell us if it ever
entered idle state.
[How]
Add debug option for IPS visual confirm
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DM can hook this up to disable SLDO optimizations in firmware during
DMCUB initialization for debug purposes.
[How]
Add the option and pass it through dmub_srv.
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add new Replay states 2A (initial Replay entry) and 4E (frame update)
to check is there is new frame update before sending
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add new condition for PSR exit due to ESD recovery
- Add new VB scaling feature for ABM by interpolating between
existing VB parameters, allowing driver to have fine grain
scaled VB levels between 0 - 250
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Create a general command and fix Replay desync error with general cmd
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
Add additional delay factor when considering a safe time to flip for HWFQ
to be passed in by the driver.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
These registers should not be read from driver and triggering the
security violation when DMCUB work times out and diagnostics are
collected blocks Z8 entry.
[How]
Remove the register read from DCN35.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Define debug interface to dmub for reading back abm data.
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Josip Pavic <josip.pavic@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Change ordering of structs to put enums together
- Add new define DMUB_TRACE_ENTRY_DEFINED to guard
the trace code enum
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The original coasting vtotal is 2 bytes, and it need to be amended to 4
bytes because low hz case.
[How]
Amend coasting vtotal from 2 bytes to 4 bytes.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: ChunTao Tso <ChunTao.Tso@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For some panel, it cannot handle pseudo vblank set by otg resync
when leave psr
[How]
The monitor patch will keep otg_on during enter IPS1.
And then we don't need to do otg resync when wake up.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Lewis Huang <lewis.huang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
Add 5ms timeout to trigger recovery and force allow P-State in DMUB.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. To support multiple PSRSU residency measurement mode
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Jack Chang <jack.chang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPD sense changes can occur during low power states and need to be
notified from firmware to driver. Upon notification the hotplug
redetection routines should execute.
[How]
Add Support in DMUB srv and DMUB srv stat for receiving these
notifications. DM can hook them up and process the HPD redetection
once received.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Add parameters for set_abm_event to enable varibright scaling.
VariBright Scaling is a feature to refer to system states like
1. Power mode
2. Battery Life percent
3. FullScreen video
4. Backlight slider
to adjust variBright strength to get low power or user experience.
[How]
Add parameters of set_abm_event for VB Scaling
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Chun-LiangChang <chuchang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
New commands for enabling copy of DC bounding box values from VBIOS DMUB
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DPIA boot option is set by VBIOS. It gets
overwritten when driver loads DMU.
[HOW]
Read PreOS boot options and determine if
dpia is enabled.
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Implement command interface to query ABM SW algorithm and
HW caps. This is primarily intended as a debugging interface
- Add new definitions for max number of histogram bins and ABM
curve segments available in hardware
- Add structures to retrieve caps to describe ABM HW caps
since not all ASICs have the same number of cure segments and
bins
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We can hang in IPS2 checking DMCUB_SCRATCH0 for link detection state.
[How]
Replace the HW access with a check on the shared state bit. This will
work the same way as the SCRATCH0 but won't require a wake in the case
where link detection isn't required.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Adjust the dmub_fw_boot_options reserved bits to be correct
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update dmub_cmd to manipulate SDP control in replay FSM, add command
for panel_cntl, expand link rate enum, and increase the reserve byte.
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
IPS ono sequence ordering differs based on the ASIC.
[How]
Detect the ASIC ID revision and set the boot option accordingly. Feed
it through the DCN35 DMUB functions.
Reviewed-by: Sung joon Kim <sungjoon.kim@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add boot option to change the ONO powerup flow, impacting
the order of power domains to power up or down first
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- Add logging for first DMUB inbox message that timed out to diagnostic
data
- It is useful to track the first failed message for debug purposes
because once DMUB becomes hung (typically on a message), it will
remain hung and all subsequent messages. In these cases we're
interested in knowing which is the first message that failed.
Reviewed-by: Josip Pavic <josip.pavic@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
Update dmub and driver interface for future FAMS revisions.
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We don't have a way to specify IPS2 for display off but RCG only for
static screen and local video playback.
[How]
Add a new setting that allows RCG only when displays are active but
IPS2 when all displays are off.
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
To enable a new interface so alternate scrambling can be done via
security module.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Sung Joon Kim <sungjoon.kim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It's possible to skip parts of the eval and exit sequencing if we know
whether DCN is in IPS2 already or if it's committed to going to idle
and not in IPS2.
[How]
Skip IPS2 entry/exit if DMCUB is idle but the IPS2 commit is not set.
Skip the eval delay if DMCUB is already in IPS2 since we know we need
to exit.
These are turned off by default.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add a Replay residency mode which only calcuates the
entry time based on replay state 0/1 switch.
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
- Update replay residency tracing design to support more types
including tracking PHY and ALPM residency types
- Add commands for Replay frame update count profiling
- Enhance HWFQ with additional flags to allow for more
optimized IPS low power state residencies
- Add new flag to indicate if a new frame update needed for
ABM to ramp up into steady state
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Add new counters in the shared IPS firmware state.
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The original coasting vtotal is 2 bytes, and it need to
be amended to 4 bytes because low hz case.
[HOW]
Amend coasting vtotal from 2 bytes to 4 bytes.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: ChunTao Tso <chuntao.tso@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DMUB support is required to light-up displays.
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VBIOS DMCUB firmware doesn't set the dal_fw bit and we end up hanging
waiting for HW power up done because of it.
[How]
Simplify the path and allow mailbox_rdy to be a functional check when
we detect VBIOS firmware.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Read modify write hazards can occur when using a single shared scratch
register between driver and firmware leading to driver accessing DCN
in IPS2 and a system hang.
[How]
Add infrastructure for using REGION6 as a shared firmware state between
driver and firmware. This region is uncachable.
Replace the existing get/set idle calls with reads/writes to the
(volatile) shared firmware state blocks that a separated by at least
a cache line between firmware and driver.
Remove the workarounds that required rewriting/checking read modify
write hazards.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Display code keeps getting improvements, and because of that, some
legacy code is left behind. This commit drops some of those unused
codes.
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add control flag for IPS residency profiling
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. To watch dmcub inbox1 ring buffer cmd type without tools
2. dmub_cmd_PLAT_54186_wa 66 bytes
[How]
Added dmcub cmd type enum: unsigned char for debug use only,
also fixed 66 bytes issue by using unsigned int in bit
define instead of unsigned char.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Fudongwang <fudong.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Otherwise we can send commands too early and they don't execute until
the next command is sent.
[How]
Check the extra status bit when polling for HW powered up.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add debug flag for Replay IPS visual confirm
- Remove unused debug flags that should not
be controlled inside Replay FSM
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Because ABM will wait VStart to start getting histogram data,
it will cause we can't enter IPS while full screnn video playing.
[How]
Modify the panel refresh rate to the maximun multiple of current
refresh rate.
Reviewed-by: Dennis Chan <dennis.chan@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: ChunTao Tso <chuntao.tso@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In dump file, GART memory can be accessed while frame buffer cannot.
[How]
Add GART memory support for dmcub.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Fudongwang <fudong.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Introduce a new Replay mode for DMUB version 0.0.199.0
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Remove unused dmub_fw_boot_options flag
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On resume from S3, while DMUB is inactive, DMUB queue and execute
calls will not work. Skip reporting errors in these scenarios
[How]
Add new return code during DMUB queue and execute calls when DMUB
is in S3 state. Skip logging errors in these scenarios
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On resume from S3, may get apply_idle_optimizations call while DMUB
is inactive which will just time out.
[How]
Set and track power state in dmub_srv and check power state before
sending commands to DMUB. Add interface in both dmub_srv and
dc_dmub_srv
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Larger data blocks are expected to be transferred between driver and FW
in the future.
[How]
Embiggen the scratch buffer to a cromulent size.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Josip Pavic <josip.pavic@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
OTG inst and pwrseq inst mapping is not align therefore we cannot use
otg_inst as pwrseq inst to get DCIO register.
[How]
1. Pass the correct pwrseq instance to dmub when set abm pipe.
2. LVTMA control index change from panel_inst to pwrseq_inst.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Phil Hsieh <phil.hsieh@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Lewis Huang <lewis.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add a new dmub command in enum dmub_cmd_cab_type
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add a tracing framework, to measure duration, execution count and
longest duration of main loop/vsync interrupt work
GPINT command is used to start/stop the measurements.
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
If Panel max link off frame count is low, it will cause low residency
for Replay, then Disabled timing sync check in Full screen Video Case.
Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Dennis Chan <dennis.chan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Sending certain Frameupdate number for Replay Power Evaluation
Reviewed-by: Dennis Chan <dennis.chan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Max Tseng <max.tseng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Augment the function to allow send different format data in different
use case.
Reviewed-by: Dennis Chan <dennis.chan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Max Tseng <max.tseng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When waiting for the ACK for INBOX0 message,
we have to ensure to include the udelay
for proper wait time
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Add new command to disable replay timing resync
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For features that are implemented primarily in DMUB (e.g. PSR), it is
useful to be able to trace them at a DMUB level from the kernel,
especially when debugging issues. So, introduce a debugfs interface that
is able to read and set the DMUB trace mask dynamically at runtime and
document how to use it.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Flush command sent to DMCUB spends more time for execution on
a dGPU than on an APU. This causes cursor lag when using high
refresh rate mouses.
[HOW]
1. Change the DMCUB mailbox memory location from FB to inbox.
2. Only change windows memory to inbox.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Lewis Huang <lewis.huang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
HW can return invalid values on register read, guard against these being
set and causing us to access memory out of range and page fault.
[HOW]
Guard at sync_inbox1 and guard at pushing commands.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Increase number of bits for IPS boot option
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
To help isolate static screen and
video playback tests, we want to enable
an IPS option to allow IPS only on D3 cycle.
[how]
Add DISABLE_DYNAMIC and DISABLE_ALL
IPS disable flags for user control.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Minor formatting changes
- Update defines to match the bit width of the field it is used for
- Add new boot up bits to control HW sub block regions power
down
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need a helper function to check idle power is allowed
so that dc doesn't access any registers that are power-gated.
[how]
Implement helper function to check idle power optimization.
Enable a hook to check if detection is allowed.
V2:
Add function hooks for set and get idle states.
Check if function hook was properly initialized.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Choi <nicholas.choi@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Rename hw_sequencer to hwseq.
Move all hwseq files to unique
folder hwss.
[how]
creating hwss repo in dc, and moved the dcnxx_hwseq.c
and .h files into corresponding new folders inside the hwss
and cleared the linkage errors by adding relative paths
in the Makefile.template.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Mounika Adhuri <moadhuri@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Revert commit 434cf7af49 ("drm/amd/display: Add a check for idle power optimization")
Because it cause Freesync and S4 regression
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Make some formatting changes and rearranging of definitions for consistency.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
* Add hints about the bits used in the packed struct.
* Update new bitfields for ABM and IPS
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need a helper function to check idle power is allowed
so that dc doesn't access any registers that are power-gated.
[how]
Implement helper function to check idle power optimization.
Enable a hook to check if detection is allowed.
Signed-off-by: Sung Joon Kim <Sungjoon.Kim@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add new IPS ALLOW masks
- Add new Replay power configuration options
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some panels request main link off before specific vertical line.
If source turn off main link after specific vertical line then
panel defect will be exposed.
[How]
Add interface to support turn off main link before specific
vertical line
Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add new params to dmub_feature_caps for checking replay
support in FW
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drivers/gpu/drm/amd/amdgpu/../display/dmub/src/dmub_srv.c:355 dmub_srv_hw_setup() warn: inconsistent indenting
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
Readback is only necessary when loaded via CPU.
Reviewed-by: Chris Park <chris.park@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Remove unused flag otg_powered_down
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
SubVP needs to "calculate" the earliest in use META address
by using the current primary / meta addresses, but this leads
to a race condition where FW and driver can read/write the
address at the same time and intermittently produce inconsistent
address offsets. To mitigate this issue without locking (too slow),
save each surface flip addr into scratch registers and use this
to keep track of the earliest in use META addres.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
DMUB subsystem was continuing to use compile time offset calculation for
register access. Switch this to runtime calculation to stay consistent
with rest of DC code.
To enable this, an additional interface init_reg_offsets() are added to
DMUB's hw_funcs struct. Asics with runtime register offset calculation
enabled shall populate this hook with a fn pointer that will invoke the
necessary macros to calculate the offset.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add defines to specify new PHY power states
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DPIA traces from DMUB is not enabled by default, which is
less convenient to debug DPIA related issues because we have
to resort to other debug tools to enable DPIA trace.
[How]
Exposes interfaces to update trace mask from the DMUB GPINT commands.
Also provides DC implementations to enable DPIA trace.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In some instances, the GPU is transmitting repeated frame to the sink
without any updates or changes in the content. These repeat transmission
are wasteful, resulting in power draw in different aspects of the system
1. DCN is fetching the frame of data from DF/UMC/DRAM. This memory traffic
prevents power down of parts of this HW path.
2. GPU is transmitting pixel data to the display through the main link of
the DisplayPort interface. This prevents power down of both the Source
transmitter (TX) and the Sink receiver (RX)
The concepts of utilizing replay is similar to PSR, but there is a benefit of:
Source and Sink remaining synchronized which allows for
- lower latency when switching from replay to live frames
- enable the possibility of more use cases
- easy control of the sink's refresh rate during replay
Due to Source and Sink remaining timing synchronized, Replay can be activated
in more UI scenarios.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This option can vary depending on the panel and may be required to be
called during sink detection phase before transmitter control.
[How]
Allow modify the bit depending on the eDP panel connected with a new
interface.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Rearranged defs order
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are grammer mistakes in comments
[How]
Correct grammar mistakes
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Reza Amini <reza.amini@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
