[Why]
It makes DSC enable when we commit the stream which need
keep power off.And then it will skip to disable DSC if
pipe reset at this situation as power has been off. It may
cause the DSC unexpected enable on the pipe with the
next new stream which doesn't support DSC.
[HOW]
Check the DSC used on current pipe status when update stream.
Skip to enable if it has been off. The operation enable
DSC should happen when set power on.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Paul Hsieh <Paul.Hsieh@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Introduce the DCC and Tiling reset callback to all DCN versions that can
call it.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Seamless boot skips MPC init for the active pipe, resulting in stale MPC
rate control state being retained. This will cause issues since other
logic assumes it is disabled (as DCN30 and newer does not need it).
[How]
Disable MPC rate control on ODM pipe update to cover the seamless boot
case.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Older Asics were changed to target new DCN while still needing older
support causing brightness adjustments to fail.
[How]
Reverted the DCN targets on required DCNs
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Iswara Nagulendran <iswara.nagulendran@amd.com>
Signed-off-by: Harry VanZyllDeJong <hvanzyll@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
mmhubbub_warmup is a field that was only read by the just removed
dc_stream_warmup_writeback() function.
Remove the field and it's initialisers.
It was only ever initialised to a single function value
(dcn30_mmhubbub_warmup) which is called explicitly elsewhere.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Implement the new backlight_level_params structure as part of the VBAC
framework, the information in this structure is needed to be passed down
to the DMCUB to identify the backlight control type, to adjust the
backlight of the panel and to perform any required conversions from PWM
to nits or vice versa.
[How]
Modified existing functions to include the new backlight_level_params
structure.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Kaitlyn Tse <Kaitlyn.Tse@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For some EDP to MIPI panel, disabling OTG when link is alive like boot
case, the converter might output garbage or show no display because our
GPU is not sending required pixel data.
Alos Dig fifo underflow was found which might cause garbage, when
resetting otg for other types of EDP panels.
[How]
Skipping resetting OTG if the dig fifo is on. Make sure that the otg for
the pipe is the one that the dig fifo is selecting via the FE mask.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Zhongwei <Zhongwei.Zhang@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Resync FIFO is a workaround to write the same value to
DENTIST_DISPCLK_CNTL register after programming OTG_PIXEL_RATE_DIV
register, in case seemless boot, there is no OTG_PIXEL_RATE_DIV register
update, so skip CRTC disable when resync FIFO to avoid random FIFO error
and garbage.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Fudongwang <Fudong.Wang@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix several copypaste mistakes in *_disable_link_output() functions where
an improper function pointer is checked before dereference.
Found by Linux Verification Center (linuxtesting.org) with Svace.
Signed-off-by: Vitaliy Shevtsov <v.shevtsov@maxima.ru>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Previous multi-display HPO fix moved where HPO I/O enable/disable is performed.
The codepath now taken to enable/disable HPO I/O is not used for compliance
test automation, meaning that if a compliance box being driven at a DP1 rate
requests retrain at UHBR, HPO I/O will remain off if it was previously off.
[HOW]
Explicitly update HPO I/O after allocating encoders for test request.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some interface functions are defined in both the public and private HWSS
interfaces, which can lead to confusion and runtime issues, therefore
the duplicates should be eliminated.
[How]
- power_down should only be private, because it's only used within HWSS.
- update_plane_addr should only be public, as it's used outside HWSS.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We resync the FIFO after each pipe update in apply_ctx_to_hw.
However, this means that some pipes (in hardware) are based on the
new context and some are based on the current_state (since the pipes
are updated on at a time). In this case we must ensure to use the
pipe_ctx that's currently still configured in hardware when turning
off / on OTG's and reconfiguring ODM during the resync.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to reconfigure ODM when resyncing FIFO because on OTG disable we
clear all ODM programming
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Vbios & Driver have difference pixel rate div policy.
When enabling fast boot & performing blank & unblank w/o timing setting,
pixel clock & pixel rate dividor are not match.
It would cause too high pixel reate and eDP would be black screen.
[How]
We would keep pixel rate div setting by Vbios until next timing setting.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: yi-lchen <yi-lchen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently 3-tap chroma subsampling is used for YCbCr422/420. When ODM
pipesplit is used, pixels on the left edge of ODM slices need one extra
pixel from the right edge of the previous slice to calculate the correct
chroma value.
Without this change, the chroma value is slightly different than
expected. This is usually imperceptible visually, but it impacts test
pattern CRCs for compliance test automation.
[HOW]
Update logic to use the register for adding extra left edge pixel for
YCbCr422/420 ODM cases.
Reviewed-by: George Shen <george.shen@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Input mode for the DIG FIFO should be programmed as part of stream
encoder setup.
[HOW]
Pre-calculate the pixels per cycle as part of the pixel clock params,
and program as part of stream encoder setup.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When optc uses two pixel per container, each ODM slice width must be an
even number.
[how]
If ODM slice width is odd number increase it by 1.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 4d4d3ff16d ("drm/amd/display: Keep VBios pixel rate div
setting util next mode set") which causes issue.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Webb Chen <yi-lchen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set up to enable log color state for multiple DCNs.
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
VBios & Driver may have differnet pixel rate div policy.
If the policy is not same and fast boot is enabled,
it would cause the pixel rate is too high
after driver only performs stream blank & unblank.
[how]
We would keep pixel rate div setting by VBios until next mode set.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Webb Chen <yi-lchen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes 29 UNINIT issues reported by Coverity.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
MPC flow rate control is not needed for DCN30 and above. Current logic
that uses it can result in underflow for certain edge cases (such as
DSC N422 + ODM combine + 422 left edge pixel).
[How]
Remove MPC flow rate control logic and programming for DCN30 and above.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The static screen event mask definition is different
betwnn DCN31 after and before.
[how]
Rename DCN30_set_static_screen_control to DCN31.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Yiling Chen <yi-ling.chen2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Move all init files to hwss folder.
[how]
moved the dcnxx_init.c and .h files into inside the hwss and cleared the
linkage errors.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Revalla <hrevalla@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Rename hw_sequencer to hwseq.
Move all hwseq files to unique
folder hwss.
[how]
creating hwss repo in dc, and moved the dcnxx_hwseq.c
and .h files into corresponding new folders inside the hwss
and cleared the linkage errors by adding relative paths
in the Makefile.template.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Mounika Adhuri <moadhuri@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
