[WHY]
These are left required changes for dio encoder refactor.
[HOW]
1. original logic is separated by config option
2. new link encoder dp enable/disable code for dcn35
3. process fec only for DP 8b10b encoding
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
Refactor existing code related to DCN4x for better code sharing with
other modules.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Swapnil Patel <Swapnil.Patel@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
BT2020 YCbCr input is not handled properly when full range
quantization is used and limited range is not supported at all.
[How]
- Add enums for BT2020 YCbCr limited/full range
- Add limited range CSC matrix
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Robert Mader <robert.mader@collabora.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove the static qualifier to make it available for code sharing
with other components.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Dmytro <dmytro.laktyushkin@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We see unstable DP LL 4.2.1.3 test result with dpia pre-train. It is
because the outbox interrupt mechanism can not handle HPD
immediately and require some improvement.
[HOW]
1. not enable link if hpd_pending is true.
2. abort pre-train if training failed and hpd_pending is true.
3. check if 2 lane supported when it is alt mode
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We like to have pretrain for dpia link so that dp and dp tunneling
have aligned behavior. The Main difficult for dpia pretrain is that
encoder can not get corresponded dpia port when link detection
in current implementation.
[HOW]
1. create enable/disable dpia output functions for dcn35 encoder
and have dpia_id and other necessary info as inputs.
2. dcn35 dpia use the new functions to enable/disable output.
3. have a option to enable/disable the change.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
misc0, temp and split_pipe are assigned but immediately re-assigned
to other values. The early assignments are useless and are removed.
Unused variables are removed as well.
This fixes 5 UNUSED_VALUE issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For some EDP to MIPI panel, disabling OTG when link is alive like boot
case, the converter might output garbage or show no display because our
GPU is not sending required pixel data.
Alos Dig fifo underflow was found which might cause garbage, when
resetting otg for other types of EDP panels.
[How]
Skipping resetting OTG if the dig fifo is on. Make sure that the otg for
the pipe is the one that the dig fifo is selecting via the FE mask.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Zhongwei <Zhongwei.Zhang@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When pre-OS firmware enables display support for displays that operate
the DIG in 2 pixels per cycle processing modes the inferred pixel rate
from get_pixel_clk_frequency_100hz does not account for the true pixel
rate since we're outputting 2 per cycle past the stream encoder.
This causes seamless boot validation to abort early.
[How]
Add a new stream encoder function for getting pixels per cycle from the
stream encoder. If the pixels per cycle is greater than 1 and the driver
policy is to enable 2 pixels per cycle for post-OS then allow seamless
boot to continue.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Moved files to respective folders to improve DIO code.
Signed-off-by: Bhuvanachandra Pinninti <bpinnint@amd.com>
Reviewed-by: Martin Leung <martin.leung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This is a workaround for an dcn3.1 hang that happens if otg dispclk
is ramped while otg is on and stream enc is off.
But this w/a should not trigger when we have a dig active.
[How]
Avoid disable otg when dig FE/BE FIFO was not switched.
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Jingwen Zhu <jingwen.zhu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Refactor the code of dio to unit test.
[how]
Moved files to respective folders and changed cMakeLists and makefiles.
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Bhuvanachandra Pinninti <bpinnint@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Move DCN3X files to unique component folder.
[how]
Create respective component folder in dc, move the DCN3X files into
corresponding new folders and made appropriate changes for compilation
in Makefiles.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Mounika Adhuri <moadhuri@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
