[why]
DPP CLK enable needs to disable DPPCLK RCG first.
The DPPCLK_en in dccg should always be enabled when the corresponding
pipe is enabled.
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
when dscclk rcg disabled from usr reg option,
dsc clock will remain enabled because driver was doing two things
both dscclk and dsc rcg in the same routine.
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are cases where an OTG is remapped from driving a regular HDMI
display to a DP/eDP display. There are also cases where DTBCLK needs to
be enabled for HPO, but DTBCLK DTO programming may be done while OTG is
still enabled which is dangerous as the PIPE_DTO_SRC_SEL programming may
change the pixel clock generator source for a mapped and running OTG and
cause it to hang.
Remove the PIPE_DTO_SRC_SEL programming from this sequence since it is
already done in program_pixel_clk(). Additionally, make sure that
program_pixel_clk sets DTBCLK DTO as source for special HDMI cases.
Cc: stable@vger.kernel.org # 6.11+
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Ovidiu Bunea <Ovidiu.Bunea@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
enable dpp rcg before we disable dppclk in hw_init cause system
hang/reboot
[How]
we remove dccg rcg related code from init into a separate function and
call it after we init pipe
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Qili Lu <qili.lu@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Function used to check the number of FEs connected to the current BE.
This was then used to determine if the symclk could be disabled, if
all FEs were disconnected. However, the function would skip over the
primary FE and return 0 when the primary FE was still connected. This
caused black screens on driver disable with an MST daisy chain hooked
up.
[How]
Refactor the function to correctly return the number of FEs connected
to the input BE. Also, rename it for clarity.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Nicholas Susanto <Nicholas.Susanto@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
post_divider_value should not be 0.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Ahmed, Muhammad <Ahmed.Ahmed@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Revert updated DCCG wrappers due to regression
[How]
This reverts commit 680458d41a.
Reviewed-by: Chris Park <chris.park@amd.com>
Signed-off-by: Hansen Dsouza <Hansen.Dsouza@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why and how]
Update to using new dccg callbacks
Reviewed-by: Chris Park <chris.park@amd.com>
Signed-off-by: Hansen Dsouza <Hansen.Dsouza@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
Add clock source selection control functions based on spec
Reviewed-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Signed-off-by: Hansen Dsouza <Hansen.Dsouza@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
Add clock source selection an control functions based on spec
Reviewed-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Signed-off-by: Hansen Dsouza <Hansen.Dsouza@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
Add new stream and char control functions based on DCCG spec
Reviewed-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Signed-off-by: Hansen Dsouza <Hansen.Dsouza@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add new enable and disable functions based on DCCG spec.
Signed-off-by: Hansen Dsouza <Hansen.Dsouza@amd.com>
Reviewed-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add new enable and disable functions based on DCCG spec.
Signed-off-by: Hansen Dsouza <Hansen.Dsouza@amd.com>
Reviewed-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
Add standard RCG helpers based on DCCG spec
Reviewed-by: Daniel Miess <daniel.miess@amd.com>
Reviewed-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Signed-off-by: Hansen Dsouza <hansen.dsouza@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Vbios & Driver have difference pixel rate div policy.
When enabling fast boot & performing blank & unblank w/o timing setting,
pixel clock & pixel rate dividor are not match.
It would cause too high pixel reate and eDP would be black screen.
[How]
We would keep pixel rate div setting by Vbios until next timing setting.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: yi-lchen <yi-lchen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit c49e44ede5.
This causes regression on DP link layer test.
Reported-by: Mark Broadworth <Mark.Broadworth@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Enable root clock optimization for SYMCLK and only
disable it when it's actively used.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
fe_clk_en has size of 5 but sizeof(fe_clk_en) has byte size 20 which is
lager than the array size.
[HOW]
Divide byte size 20 by its element size.
This fixes 2 OVERRUN issues reported by Coverity.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
cleaning up the code refactor requires dccg to be in its own component.
[how]
move all files under newly created dccg folder and fixing the
makefiles.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Revalla Hari Krishna <harikrishna.revalla@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
