The conversion of all GPIO drivers to using the .set_rv() and
.set_multiple_rv() callbacks from struct gpio_chip (which - unlike their
predecessors - return an integer and allow the controller drivers to
indicate failures to users) is now complete and the legacy ones have
been removed. Rename the new callbacks back to their original names in
one sweeping change.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
struct gpio_chip now has additional variants of the set(_multiple)
driver callbacks that return an integer to indicate success or failure.
Convert the driver to using them.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20250220-gpio-set-retval-v2-13-bc4cfd38dae3@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Use lock guards from linux/cleanup.h. This will make the subsequent
commit that switches to using value returning GPIO line setters much
simpler as we'll be able to return values without caring about releasing
the locks.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20250220-gpio-set-retval-v2-12-bc4cfd38dae3@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Change the in-kernel consumer interface for GPIOs: make all variants of
value setters that don't have a return value, return a signed integer
instead. That will allow these routines to indicate failures to callers.
This doesn't change the implementation just yet, we'll do it in
subsequent commits.
We need to update the gpio-latch module as it passes the address of
value setters as a function pointer argument and thus cares about its
type.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20250220-gpio-set-retval-v2-2-bc4cfd38dae3@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Make the code a bit more readable by using a helper variable to store
the address of pdev->dev in probe().
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20250211120847.42437-2-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Replace calls to OF-specific interface with generic device property
getters. This is good practice and also drops implicit run-time
dependency on CONFIG_OF.
Link: https://lore.kernel.org/r/20250211120847.42437-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This driver implements a GPIO multiplexer based on latches connected to
other GPIOs. A set of data GPIOs is connected to the data input of
multiple latches. The clock input of each latch is driven by another
set of GPIOs. With two 8-bit latches 10 GPIOs can be multiplexed into
16 GPIOs. GPOs might be a better term as in fact the multiplexed pins
are output only.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[Bartosz: fixed the strange of_device_id formatting]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
