Enumerate all available DPLL channels and registers a DPLL device for
each of them. Check all input references and outputs and register
DPLL pins for them.
Number of registered DPLL pins depends on configuration of references
and outputs. If the reference or output is configured as differential
one then only one DPLL pin is registered. Both references and outputs
can be also disabled from firmware configuration and in this case
no DPLL pins are registered.
All registrable references are registered to all available DPLL devices
with exception of DPLLs that are configured in NCO (numerically
controlled oscillator) mode. In this mode DPLL channel acts as PHC and
cannot be locked to any reference.
Device outputs are connected to one of synthesizers and each synthesizer
is driven by some DPLL channel. So output pins belonging to given output
are registered to DPLL device that drives associated synthesizer.
Finally add kworker task to monitor async changes on all DPLL channels
and input pins and to notify about them DPLL core. Output pins are not
monitored as their parameters are not changed asynchronously by the
device.
Co-developed-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250704182202.1641943-9-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for reading of DPLL types and optional pin properties from
the system firmware (DT, ACPI...).
The DPLL types are stored in property 'dpll-types' as string array and
possible values 'pps' and 'eec' are mapped to DPLL enums DPLL_TYPE_PPS
and DPLL_TYPE_EEC.
The pin properties are stored under 'input-pins' and 'output-pins'
sub-nodes and the following ones are supported:
* reg
integer that specifies pin index
* label
string that is used by driver as board label
* connection-type
string that indicates pin connection type
* supported-frequencies-hz
array of u64 values what frequencies are supported / allowed for
given pin with respect to hardware wiring
Do not blindly trust system firmware and filter out frequencies that
cannot be configured/represented in device (input frequencies have to
be factorized by one of the base frequencies and output frequencies have
to divide configured synthesizer frequency).
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250704182202.1641943-8-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Microchip Azurite ZL3073x represents chip family providing DPLL
and optionally PHC (PTP) functionality. The chips can be connected
be connected over I2C or SPI bus.
They have the following characteristics:
* up to 5 separate DPLL units (channels)
* 5 synthesizers
* 10 input pins (references)
* 10 outputs
* 20 output pins (output pin pair shares one output)
* Each reference and output can operate in either differential or
single-ended mode (differential mode uses 2 pins)
* Each output is connected to one of the synthesizers
* Each synthesizer is driven by one of the DPLL unit
The device uses 7-bit addresses and 8-bits values. It exposes 8-, 16-,
32- and 48-bits registers in address range <0x000,0x77F>. Due to 7bit
addressing, the range is organized into pages of 128 bytes, with each
page containing a page selector register at address 0x7F.
For reading/writing multi-byte registers, the device supports bulk
transfers.
Add basic functionality to access device registers, probe functionality
both I2C and SPI cases and add devlink support to provide info and
to set clock ID parameter.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250704182202.1641943-6-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
