When making ZL3073X invisible, it was overlooked that ZL3073X depends on
NET, while ZL3073X_I2C and ZL3073X_SPI do not, causing:
WARNING: unmet direct dependencies detected for ZL3073X when selected by ZL3073X_I2C
WARNING: unmet direct dependencies detected for ZL3073X when selected by ZL3073X_SPI
WARNING: unmet direct dependencies detected for ZL3073X
Depends on [n]: NET [=n]
Selected by [y]:
- ZL3073X_I2C [=y] && I2C [=y]
Selected by [y]:
- ZL3073X_SPI [=y] && SPI [=y]
Fix this by adding the missing dependencies to ZL3073X_I2C and
ZL3073X_SPI.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202508022110.nTqZ5Ylu-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202508022351.NHIxPF8j-lkp@intel.com/
Fixes: a4f0866e3d ("dpll: Make ZL3073X invisible")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20250802155302.3673457-1-geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the user is always asked about the Microchip Azurite
DPLL/PTP/SyncE core driver, even when I2C and SPI are disabled, and thus
the driver cannot be used at all.
Fix this by making the Kconfig symbol for the core driver invisible
(unless compile-testing), and selecting it by the bus glue sub-drivers.
Drop the modular defaults, as drivers should not default to enabled.
Fixes: 2df8e64e01 ("dpll: Add basic Microchip ZL3073x support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/97804163aeb262f0e0706d00c29d9bb751844454.1753874405.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If CONFIG_ZL3073X is enabled but both CONFIG_ZL3073X_I2C and
CONFIG_ZL3073X_SPI are disabled, the compilation may fail because
CONFIG_REGMAP is not enabled.
Fix the issue by selecting CONFIG_REGMAP when CONFIG_ZL3073X is enabled.
Fixes: 2df8e64e01 ("dpll: Add basic Microchip ZL3073x support")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20250726184145.25769-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Adds support to get fractional frequency offset for input pins. Implement
the appropriate callback and function that periodicaly performs reference
frequency measurement and notifies DPLL core about changes.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Tested-by: Prathosh Satish <prathosh.satish@microchip.com>
Co-developed-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20250715144633.149156-6-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support to get/set phase adjustment for both input and output pins.
The phase adjustment is implemented using reference and output phase
offset compensation registers. For input pins the adjustment value can
be arbitrary number but for outputs the value has to be a multiple
of half synthesizer clock cycles.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Tested-by: Prathosh Satish <prathosh.satish@microchip.com>
Co-developed-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20250715144633.149156-5-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Implement phase offset monitor feature to allow a user to monitor
phase offsets across all available inputs.
The device firmware periodically performs phase offsets measurements for
all available DPLL channels and input references. The driver can ask
the firmware to fill appropriate latch registers with measured values.
There are 2 sets of latch registers for phase offsets reporting:
1) DPLL-to-connected-ref: up to 5 registers that contain values for
phase offset between particular DPLL channel and its connected input
reference.
2) selected-DPLL-to-ref: 10 registers that contain values for phase
offsets between selected DPLL channel and all available input
references.
Both are filled with single read request so the driver can read
DPLL-to-connected-ref phase offset for all DPLL channels at once.
This was implemented in the previous patch.
To read selected-DPLL-to-ref registers for all DPLLs a separate read
request has to be sent to device firmware for each DPLL channel.
To implement phase offset monitor feature:
* Extend zl3073x_ref_phase_offsets_update() to select given DPLL channel
in phase offset read request. The caller can set channel==-1 if it
will not read Type2 registers.
* Use this extended function to update phase offset latch registers
during zl3073x_dpll_changes_check() call if phase monitor is enabled
* Extend zl3073x_dpll_pin_phase_offset_check() to check phase offset
changes for all available input references
* Extend zl3073x_dpll_input_pin_phase_offset_get() to report phase
offset values for all available input references
* Implement phase offset monitor callbacks to enable/disable this
feature
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Tested-by: Prathosh Satish <prathosh.satish@microchip.com>
Co-developed-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20250715144633.149156-4-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support to get phase offset for the connected input pin. Implement
the appropriate callback and function that performs DPLL to connected
reference phase error measurement and notifies DPLL core about changes.
The measurement is performed internally by device on background 40 times
per second but the measured value is read each second and compared with
previous value.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Tested-by: Prathosh Satish <prathosh.satish@microchip.com>
Co-developed-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20250715144633.149156-3-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support to get/set embedded sync for both input and output pins.
The DPLL is able to lock on input reference when the embedded sync
frequency is 1 PPS and pulse width 25%. The esync on outputs are more
versatille and theoretically supports any esync frequency that divides
current output frequency but for now support the same that supported on
input pins (1 PPS & 25% pulse).
Note that for the output pins the esync divisor shares the same register
used for N-divided signal formats. Due to this the esync cannot be
enabled on outputs configured with one of the N-divided signal formats.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Tested-by: Prathosh Satish <prathosh.satish@microchip.com>
Co-developed-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20250715144633.149156-2-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support to get/set frequency on pins. The frequency for input
pins (references) is computed in the device according this formula:
freq = base_freq * multiplier * (nominator / denominator)
where the base_freq comes from the list of supported base frequencies
and other parameters are arbitrary numbers. All these parameters are
16-bit unsigned integers.
The frequency for output pin is determined by the frequency of
synthesizer the output pin is connected to and divisor of the output
to which is the given pin belongs. The resulting frequency of the
P-pin and the N-pin from this output pair depends on the signal
format of this output pair.
The device supports so-called N-divided signal formats where for the
N-pin there is an additional divisor. The frequencies for both pins
from such output pair are computed:
P-pin-freq = synth_freq / output_div
N-pin-freq = synth_freq / output_div / n_div
For other signal-format types both P and N pin have the same frequency
based only synth frequency and output divisor.
Implement output pin callbacks to get and set frequency. The frequency
setting for the output non-N-divided signal format is simple as we have
to compute just new output divisor. For N-divided formats it is more
complex because by changing of output divisor we change frequency for
both P and N pins. In this case if we are changing frequency for P-pin
we have to compute also new N-divisor for N-pin to keep its current
frequency. From this and the above it follows that the frequency of
the N-pin cannot be higher than the frequency of the P-pin and the
callback must take this limitation into account.
Co-developed-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250704182202.1641943-13-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement input pin state setting when the DPLL is running in automatic
mode. Unlike manual mode, the DPLL mode switching is not used here and
the implementation uses special priority value (15) to make the given
pin non-selectable.
When the user sets state of the pin as disconnected the driver
internally sets its priority in HW to 15 that prevents the DPLL to
choose this input pin. Conversely, if the pin status is set to
selectable, the driver sets the pin priority in HW to the original saved
value.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250704182202.1641943-12-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for getting and setting input pin priority. Implement
required callbacks and set appropriate capability for input pins.
Although the pin priority make sense only if the DPLL is running in
automatic mode we have to expose this capability unconditionally because
input pins (references) are shared between all DPLLs where one of them
can run in automatic mode while the other one not.
Co-developed-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250704182202.1641943-11-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement input pin state setting if the DPLL is running in manual mode.
The driver indicates manual mode if the DPLL mode is one of ref-lock,
forced-holdover, freerun.
Use these modes to implement input pin state change between connected
and disconnected states. When the user set the particular pin as
connected the driver marks this input pin as forced reference and
switches the DPLL mode to ref-lock. When the use set the pin as
disconnected the driver switches the DPLL to freerun or forced holdover
mode. The switch to holdover mode is done if the DPLL has holdover
capability (e.g is currently locked with holdover acquired).
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250704182202.1641943-10-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enumerate all available DPLL channels and registers a DPLL device for
each of them. Check all input references and outputs and register
DPLL pins for them.
Number of registered DPLL pins depends on configuration of references
and outputs. If the reference or output is configured as differential
one then only one DPLL pin is registered. Both references and outputs
can be also disabled from firmware configuration and in this case
no DPLL pins are registered.
All registrable references are registered to all available DPLL devices
with exception of DPLLs that are configured in NCO (numerically
controlled oscillator) mode. In this mode DPLL channel acts as PHC and
cannot be locked to any reference.
Device outputs are connected to one of synthesizers and each synthesizer
is driven by some DPLL channel. So output pins belonging to given output
are registered to DPLL device that drives associated synthesizer.
Finally add kworker task to monitor async changes on all DPLL channels
and input pins and to notify about them DPLL core. Output pins are not
monitored as their parameters are not changed asynchronously by the
device.
Co-developed-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250704182202.1641943-9-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for reading of DPLL types and optional pin properties from
the system firmware (DT, ACPI...).
The DPLL types are stored in property 'dpll-types' as string array and
possible values 'pps' and 'eec' are mapped to DPLL enums DPLL_TYPE_PPS
and DPLL_TYPE_EEC.
The pin properties are stored under 'input-pins' and 'output-pins'
sub-nodes and the following ones are supported:
* reg
integer that specifies pin index
* label
string that is used by driver as board label
* connection-type
string that indicates pin connection type
* supported-frequencies-hz
array of u64 values what frequencies are supported / allowed for
given pin with respect to hardware wiring
Do not blindly trust system firmware and filter out frequencies that
cannot be configured/represented in device (input frequencies have to
be factorized by one of the base frequencies and output frequencies have
to divide configured synthesizer frequency).
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250704182202.1641943-8-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Several configuration parameters will remain constant at runtime,
so we can load them during probe to avoid excessive reads from
the hardware.
Read the following parameters from the device during probe and store
them for later use:
* enablement status and frequencies of the synthesizers and their
associated DPLL channels
* enablement status and type (single-ended or differential) of input pins
* associated synthesizers, signal format, and enablement status of
outputs
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250704182202.1641943-7-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Microchip Azurite ZL3073x represents chip family providing DPLL
and optionally PHC (PTP) functionality. The chips can be connected
be connected over I2C or SPI bus.
They have the following characteristics:
* up to 5 separate DPLL units (channels)
* 5 synthesizers
* 10 input pins (references)
* 10 outputs
* 20 output pins (output pin pair shares one output)
* Each reference and output can operate in either differential or
single-ended mode (differential mode uses 2 pins)
* Each output is connected to one of the synthesizers
* Each synthesizer is driven by one of the DPLL unit
The device uses 7-bit addresses and 8-bits values. It exposes 8-, 16-,
32- and 48-bits registers in address range <0x000,0x77F>. Due to 7bit
addressing, the range is organized into pages of 128 bytes, with each
page containing a page selector register at address 0x7F.
For reading/writing multi-byte registers, the device supports bulk
transfers.
Add basic functionality to access device registers, probe functionality
both I2C and SPI cases and add devlink support to provide info and
to set clock ID parameter.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250704182202.1641943-6-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
