Remove double initialization of the reg variable.
This is to fix the following warning when compiling the QAT driver
using clang scan-build:
drivers/crypto/intel/qat/qat_common/adf_gen4_ras.c:1010:6: warning: Value stored to 'reg' during its initialization is never read [deadcode.DeadStores]
1010 | u32 reg = ADF_CSR_RD(csr, ADF_GEN4_SSMCPPERR);
| ^~~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/crypto/intel/qat/qat_common/adf_gen4_ras.c:1109:6: warning: Value stored to 'reg' during its initialization is never read [deadcode.DeadStores]
1109 | u32 reg = ADF_CSR_RD(csr, ADF_GEN4_SER_ERR_SSMSH);
| ^~~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 99b1c9826e ("crypto: qat - count QAT GEN4 errors")
Signed-off-by: Adam Guerin <adam.guerin@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Check if delta_us is not zero and return -EINVAL if it is.
delta_us is unlikely to be zero as there is a sleep between the reads of
the two timestamps.
This is to fix the following warning when compiling the QAT driver
using clang scan-build:
drivers/crypto/intel/qat/qat_common/adf_clock.c:87:9: warning: Division by zero [core.DivideZero]
87 | temp = DIV_ROUND_CLOSEST_ULL(temp, delta_us);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: e2980ba57e ("crypto: qat - add measure clock frequency")
Signed-off-by: Adam Guerin <adam.guerin@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This macro was added but never used, remove it.
This is to fix the following warning when compiling the QAT driver
using the clang compiler with CC=clang W=2:
drivers/crypto/intel/qat/qat_common/adf_cnv_dbgfs.c:19:9: warning: macro is not used [-Wunused-macros]
19 | #define CNV_SLICE_ERR_MASK GENMASK(7, 0)
| ^
Fixes: d807f0240c ("crypto: qat - add cnv_errors debugfs file")
Signed-off-by: Adam Guerin <adam.guerin@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As a result of the removal of qat_zlib_deflate, some defines where not
removed. Remove them.
This is to fix the following warning when compiling the QAT driver
using the clang compiler with CC=clang W=2:
drivers/crypto/intel/qat/qat_common/qat_comp_algs.c:21:9: warning: macro is not used [-Wunused-macros]
21 | #define QAT_RFC_1950_CM_OFFSET 4
| ^
drivers/crypto/intel/qat/qat_common/qat_comp_algs.c:16:9: warning: macro is not used [-Wunused-macros]
16 | #define QAT_RFC_1950_HDR_SIZE 2
| ^
drivers/crypto/intel/qat/qat_common/qat_comp_algs.c:17:9: warning: macro is not used [-Wunused-macros]
17 | #define QAT_RFC_1950_FOOTER_SIZE 4
| ^
drivers/crypto/intel/qat/qat_common/qat_comp_algs.c:22:9: warning: macro is not used [-Wunused-macros]
22 | #define QAT_RFC_1950_DICT_MASK 0x20
| ^
drivers/crypto/intel/qat/qat_common/qat_comp_algs.c:18:9: warning: macro is not used [-Wunused-macros]
18 | #define QAT_RFC_1950_CM_DEFLATE 8
| ^
drivers/crypto/intel/qat/qat_common/qat_comp_algs.c:20:9: warning: macro is not used [-Wunused-macros]
20 | #define QAT_RFC_1950_CM_MASK 0x0f
| ^
drivers/crypto/intel/qat/qat_common/qat_comp_algs.c:23:9: warning: macro is not used [-Wunused-macros]
23 | #define QAT_RFC_1950_COMP_HDR 0x785e
| ^
drivers/crypto/intel/qat/qat_common/qat_comp_algs.c:19:9: warning: macro is not used [-Wunused-macros]
19 | #define QAT_RFC_1950_CM_DEFLATE_CINFO_32K 7
| ^
Fixes: e9dd20e0e5 ("crypto: qat - Remove zlib-deflate")
Signed-off-by: Adam Guerin <adam.guerin@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There are a few issues in this code. If *ppos is non-zero then the
first part of the buffer is not initialized. We never initialize the
last character of the buffer. The return is not checked so it's
possible that none of the buffer is initialized.
This is debugfs code which is root only and the impact of these bugs is
very small. However, it's still worth fixing. To fix this:
1) Check that *ppos is zero.
2) Use copy_from_user() instead of simple_write_to_buffer().
3) Explicitly add a NUL terminator.
Fixes: e2b67859ab ("crypto: qat - add heartbeat error simulator")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
During the PCI AER system's error recovery process, the kernel driver
may encounter a race condition with freeing the reset_data structure's
memory. If the device restart will take more than 10 seconds the function
scheduling that restart will exit due to a timeout, and the reset_data
structure will be freed. However, this data structure is used for
completion notification after the restart is completed, which leads
to a UAF bug.
This results in a KFENCE bug notice.
BUG: KFENCE: use-after-free read in adf_device_reset_worker+0x38/0xa0 [intel_qat]
Use-after-free read at 0x00000000bc56fddf (in kfence-#142):
adf_device_reset_worker+0x38/0xa0 [intel_qat]
process_one_work+0x173/0x340
To resolve this race condition, the memory associated to the container
of the work_struct is freed on the worker if the timeout expired,
otherwise on the function that schedules the worker.
The timeout detection can be done by checking if the caller is
still waiting for completion or not by using completion_done() function.
Fixes: d8cba25d2c ("crypto: qat - Intel(R) QAT driver framework")
Cc: <stable@vger.kernel.org>
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The implementation of the Rate Limiting (RL) feature includes the cleanup
of all SLAs during device shutdown. For each SLA, the firmware is notified
of the removal through an admin message, the data structures that take
into account the budgets are updated and the memory is freed.
However, this explicit cleanup is not necessary as (1) the device is
reset, and the firmware state is lost and (2) all RL data structures
are freed anyway.
In addition, if the device is unresponsive, for example after a PCI
AER error is detected, the admin interface might not be available.
This might slow down the shutdown sequence and cause a timeout in
the recovery flows which in turn makes the driver believe that the
device is not recoverable.
Fix by replacing the explicit SLAs removal with just a free of the
SLA data structures.
Fixes: d9fb840837 ("crypto: qat - add rate limiting feature to qat_4xxx")
Cc: <stable@vger.kernel.org>
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Rework the AER reset and recovery flow to take into account root port
integrated devices that gets reset between the error detected and the
slot reset callbacks.
In adf_error_detected() the devices is gracefully shut down. The worker
threads are disabled, the error conditions are notified to listeners and
through PFVF comms and finally the device is reset as part of
adf_dev_down().
In adf_slot_reset(), the device is brought up again. If SRIOV VFs were
enabled before reset, these are re-enabled and VFs are notified of
restarting through PFVF comms.
Signed-off-by: Mun Chun Yep <mun.chun.yep@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Markas Rapoportas <markas.rapoportas@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When the driver detects an heartbeat failure, it starts the recovery
flow. Set a limit so that the number of events is limited in case the
heartbeat status is read too frequently.
Signed-off-by: Furong Zhou <furong.zhou@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Markas Rapoportas <markas.rapoportas@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Mun Chun Yep <mun.chun.yep@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Expose the `auto_reset` sysfs attribute to configure the driver to reset
the device when a fatal error is detected.
When auto reset is enabled, the driver resets the device when it detects
either an heartbeat failure or a fatal error through an interrupt.
This patch is based on earlier work done by Shashank Gupta.
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Markas Rapoportas <markas.rapoportas@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Mun Chun Yep <mun.chun.yep@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Notify a fatal error condition and optionally reset the device in
the following cases:
* if the device reports an uncorrectable fatal error through an
interrupt
* if the heartbeat feature detects that the device is not
responding
This patch is based on earlier work done by Shashank Gupta.
Signed-off-by: Mun Chun Yep <mun.chun.yep@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Markas Rapoportas <markas.rapoportas@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When a Physical Function (PF) is reset, SR-IOV gets disabled, making the
associated Virtual Functions (VFs) unavailable. Even after reset and
using pci_restore_state, VFs remain uncreated because the numvfs still
at 0. Therefore, it's necessary to reconfigure SR-IOV to re-enable VFs.
This commit introduces the ADF_SRIOV_ENABLED configuration flag to cache
the SR-IOV enablement state. SR-IOV is only re-enabled if it was
previously configured.
This commit also introduces a dedicated workqueue without
`WQ_MEM_RECLAIM` flag for enabling SR-IOV during Heartbeat and CPM error
resets, preventing workqueue flushing warning.
This patch is based on earlier work done by Shashank Gupta.
Signed-off-by: Mun Chun Yep <mun.chun.yep@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Markas Rapoportas <markas.rapoportas@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Update the PFVF logic to handle restart and recovery. This adds the
following functions:
* adf_pf2vf_notify_fatal_error(): allows the PF to notify VFs that the
device detected a fatal error and requires a reset. This sends to
VF the event `ADF_PF2VF_MSGTYPE_FATAL_ERROR`.
* adf_pf2vf_wait_for_restarting_complete(): allows the PF to wait for
`ADF_VF2PF_MSGTYPE_RESTARTING_COMPLETE` events from active VFs
before proceeding with a reset.
* adf_pf2vf_notify_restarted(): enables the PF to notify VFs with
an `ADF_PF2VF_MSGTYPE_RESTARTED` event after recovery, indicating that
the device is back to normal. This prompts VF drivers switch back to
use the accelerator for workload processing.
These changes improve the communication and synchronization between PF
and VF drivers during system restart and recovery processes.
Signed-off-by: Mun Chun Yep <mun.chun.yep@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Markas Rapoportas <markas.rapoportas@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Disable arbitration to avoid new requests to be processed before
resetting a device.
This is needed so that new requests are not fetched when an error is
detected.
Signed-off-by: Furong Zhou <furong.zhou@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Markas Rapoportas <markas.rapoportas@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Mun Chun Yep <mun.chun.yep@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add error notify method to report a fatal error event to all the
subsystems registered. In addition expose an API,
adf_notify_fatal_error(), that allows to trigger a fatal error
notification asynchronously in the context of a workqueue.
This will be invoked when a fatal error is detected by the ISR or
through Heartbeat.
Signed-off-by: Furong Zhou <furong.zhou@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Markas Rapoportas <markas.rapoportas@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Mun Chun Yep <mun.chun.yep@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a mechanism that allows to inject a heartbeat error for testing
purposes.
A new attribute `inject_error` is added to debugfs for each QAT device.
Upon a write on this attribute, the driver will inject an error on the
device which can then be detected by the heartbeat feature.
Errors are breaking the device functionality thus they require a
device reset in order to be recovered.
This functionality is not compiled by default, to enable it
CRYPTO_DEV_QAT_ERROR_INJECTION must be set.
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Markas Rapoportas <markas.rapoportas@intel.com>
Signed-off-by: Mun Chun Yep <mun.chun.yep@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
So, use the purpose specific kcalloc_node() function instead of the
argument count * size in the kzalloc_node() function.
Link: https://www.kernel.org/doc/html/next/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments [1]
Link: https://github.com/KSPP/linux/issues/162
Signed-off-by: Erick Archer <erick.archer@gmx.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The use of array_size() leads gcc to assume the memcpy() can have a larger
limit than actually possible, which triggers a string fortification warning:
In file included from include/linux/string.h:296,
from include/linux/bitmap.h:12,
from include/linux/cpumask.h:12,
from include/linux/sched.h:16,
from include/linux/delay.h:23,
from include/linux/iopoll.h:12,
from drivers/crypto/intel/qat/qat_common/adf_gen4_hw_data.c:3:
In function 'fortify_memcpy_chk',
inlined from 'adf_gen4_init_thd2arb_map' at drivers/crypto/intel/qat/qat_common/adf_gen4_hw_data.c:401:3:
include/linux/fortify-string.h:579:4: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
579 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/fortify-string.h:588:4: error: call to '__read_overflow2_field' declared with attribute warning: detected read beyond size of field (2nd parameter); maybe use struct_group()? [-Werror=attribute-warning]
588 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Add an explicit range check to avoid this.
Fixes: 5da6a2d535 ("crypto: qat - generate dynamically arbiter mappings")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The thread-to-arbiter mapping describes which arbiter can assign jobs
to an acceleration engine thread.
The existing mappings are functionally correct, but hardcoded and not
optimized.
Replace the static mappings with an algorithm that generates optimal
mappings, based on the loaded configuration.
The logic has been made common so that it can be shared between all
QAT GEN4 devices.
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Expose through debugfs ring pair telemetry data for QAT GEN4 devices.
This allows to gather metrics about the PCIe channel and device TLB for
a selected ring pair. It is possible to monitor maximum 4 ring pairs at
the time per device.
For details, refer to debugfs-driver-qat_telemetry in Documentation/ABI.
This patch is based on earlier work done by Wojciech Ziemba.
Signed-off-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Expose through debugfs device telemetry data for QAT GEN4 devices.
This allows to gather metrics about the performance and the utilization
of a device. In particular, statistics on (1) the utilization of the
PCIe channel, (2) address translation, when SVA is enabled and (3) the
internal engines for crypto and data compression.
If telemetry is supported by the firmware, the driver allocates a DMA
region and a circular buffer. When telemetry is enabled, through the
`control` attribute in debugfs, the driver sends to the firmware, via
the admin interface, the `TL_START` command. This triggers the device to
periodically gather telemetry data from hardware registers and write it
into the DMA memory region. The device writes into the shared region
every second.
The driver, every 500ms, snapshots the DMA shared region into the
circular buffer. This is then used to compute basic metric
(min/max/average) on each counter, every time the `device_data` attribute
is queried.
Telemetry counters are exposed through debugfs in the folder
/sys/kernel/debug/qat_<device>_<BDF>/telemetry.
For details, refer to debugfs-driver-qat_telemetry in Documentation/ABI.
This patch is based on earlier work done by Wojciech Ziemba.
Signed-off-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Extend the admin interface with two new public APIs to enable
and disable the telemetry feature: adf_send_admin_tl_start() and
adf_send_admin_tl_stop().
The first, sends to the firmware, through the ICP_QAT_FW_TL_START
message, the IO address where the firmware will write telemetry
metrics and a list of ring pairs (maximum 4) to be monitored.
It returns the number of accelerators of each type supported by
this hardware. After this message is sent, the firmware starts
periodically reporting telemetry data using by writing into the
dma buffer specified as input.
The second, sends the admin message ICP_QAT_FW_TL_STOP
which stops the reporting of telemetry data.
This patch is based on earlier work done by Wojciech Ziemba.
Signed-off-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
GET_DEV() macro expansion relies on struct pci_dev being defined.
Include <linux/pci.h> at adf_accel_devices.h.
Signed-off-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for 420xx devices by including a new device driver that
supports such devices, updates to the firmware loader and capabilities.
Compared to 4xxx devices, 420xx devices have more acceleration engines
(16 service engines and 1 admin) and support the wireless cipher
algorithms ZUC and Snow 3G.
Signed-off-by: Jie Wang <jie.wang@intel.com>
Co-developed-by: Dong Xie <dong.xie@intel.com>
Signed-off-by: Dong Xie <dong.xie@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Relocate the structures adf_fw_objs and adf_fw_config from the file
adf_4xxx_hw_data.c to the newly created adf_fw_config.h.
These structures will be used by new device drivers.
This does not introduce any functional change.
Signed-off-by: Jie Wang <jie.wang@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move logic that is common between QAT GEN4 accelerators to the
qat_common folder. This includes addresses of CSRs, setters and
configuration logic.
When moved, functions and defines have been renamed from 4XXX to GEN4.
Code specific to the device is moved to the file adf_gen4_hw_data.c.
Code related to configuration is moved to the newly created
adf_gen4_config.c.
This does not introduce any functional change.
Signed-off-by: Jie Wang <jie.wang@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add accel_dev as parameter of the function uof_get_num_objs().
This is in preparation for the introduction of the QAT 420xx driver as
it will allow to reconfigure the ae_mask when a configuration that does
not require all AEs is loaded on the device.
This does not introduce any functional change.
Signed-off-by: Jie Wang <jie.wang@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move the function get_service_enabled() from adf_4xxx_hw_data.c to
adf_cfg_services.c and rename it as adf_get_service_enabled().
This function is not specific to the 4xxx and will be used by
other QAT drivers.
This does not introduce any functional change.
Signed-off-by: Jie Wang <jie.wang@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is a possibility that the function adf_devmgr_pci_to_accel_dev()
might return a NULL pointer.
Add a NULL pointer check in the function rp2srv_show().
Fixes: dbc8876dd8 ("crypto: qat - add rp2svc sysfs attribute")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: David Guckian <david.guckian@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If the function validate_user_input() returns an error, the error path
attempts to unlock an unacquired mutex.
Acquire the mutex before calling validate_user_input(). This is not
strictly necessary but simplifies the code.
Fixes: d9fb840837 ("crypto: qat - add rate limiting feature to qat_4xxx")
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The input argument `sla_in` is a pointer to a structure that contains
the parameters of the SLA which is being added or updated.
If this pointer is NULL, the function should return an error as
the data required for the algorithm is not available.
By mistake, the logic jumps to the error path which dereferences
the pointer.
This results in a warnings reported by the static analyzer Smatch when
executed without a database:
drivers/crypto/intel/qat/qat_common/adf_rl.c:871 add_update_sla()
error: we previously assumed 'sla_in' could be null (see line 812)
This issue was not found in internal testing as the pointer cannot be
NULL. The function add_update_sla() is only called (indirectly) by
the rate limiting sysfs interface implementation in adf_sysfs_rl.c
which ensures that the data structure is allocated and valid. This is
also proven by the fact that Smatch executed with a database does not
report such error.
Fix it by returning with error if the pointer `sla_in` is NULL.
Fixes: d9fb840837 ("crypto: qat - add rate limiting feature to qat_4xxx")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The qat_rl sysfs attribute group is registered within the adf_dev_start()
function, alongside other driver components.
If any of the functions preceding the group registration fails,
the adf_dev_start() function returns, and the caller, to undo the
operation, invokes adf_dev_stop() followed by adf_dev_shutdown().
However, the current flow lacks information about whether the
registration of the qat_rl attribute group was successful or not.
In cases where this condition is encountered, an error similar to
the following might be reported:
4xxx 0000:6b:00.0: Starting device qat_dev0
4xxx 0000:6b:00.0: qat_dev0 started 9 acceleration engines
4xxx 0000:6b:00.0: Failed to send init message
4xxx 0000:6b:00.0: Failed to start device qat_dev0
sysfs group 'qat_rl' not found for kobject '0000:6b:00.0'
...
sysfs_remove_groups+0x2d/0x50
adf_sysfs_rl_rm+0x44/0x70 [intel_qat]
adf_rl_stop+0x2d/0xb0 [intel_qat]
adf_dev_stop+0x33/0x1d0 [intel_qat]
adf_dev_down+0xf1/0x150 [intel_qat]
...
4xxx 0000:6b:00.0: qat_dev0 stopped 9 acceleration engines
4xxx 0000:6b:00.0: Resetting device qat_dev0
To prevent attempting to remove attributes from a group that has not
been added yet, a flag named 'sysfs_added' is introduced. This flag
is set to true upon the successful registration of the attribute group.
Fixes: d9fb840837 ("crypto: qat - add rate limiting feature to qat_4xxx")
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The qat_ras sysfs attribute group is registered within the
adf_dev_start() function, alongside other driver components.
If any of the functions preceding the group registration fails,
the adf_dev_start() function returns, and the caller, to undo the
operation, invokes adf_dev_stop() followed by adf_dev_shutdown().
However, the current flow lacks information about whether the
registration of the qat_ras attribute group was successful or not.
In cases where this condition is encountered, an error similar to
the following might be reported:
4xxx 0000:6b:00.0: Starting device qat_dev0
4xxx 0000:6b:00.0: qat_dev0 started 9 acceleration engines
4xxx 0000:6b:00.0: Failed to send init message
4xxx 0000:6b:00.0: Failed to start device qat_dev0
sysfs group 'qat_ras' not found for kobject '0000:6b:00.0'
...
sysfs_remove_groups+0x29/0x50
adf_sysfs_stop_ras+0x4b/0x80 [intel_qat]
adf_dev_stop+0x43/0x1d0 [intel_qat]
adf_dev_down+0x4b/0x150 [intel_qat]
...
4xxx 0000:6b:00.0: qat_dev0 stopped 9 acceleration engines
4xxx 0000:6b:00.0: Resetting device qat_dev0
To prevent attempting to remove attributes from a group that has not
been added yet, a flag named 'sysfs_added' is introduced. This flag
is set to true upon the successful registration of the attribute group.
Fixes: 532d7f6bc4 ("crypto: qat - add error counters")
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The "ring" variable has an upper bounds check but nothing checks for
negatives. This code uses kstrtouint() already and it was obviously
intended to be declared as unsigned int. Make it so.
Fixes: dbc8876dd8 ("crypto: qat - add rp2svc sysfs attribute")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If a request has the flag CRYPTO_TFM_REQ_MAY_BACKLOG set, the function
qat_alg_send_message_maybacklog(), enqueues it in a backlog list if
either (1) there is already at least one request in the backlog list, or
(2) the HW ring is nearly full or (3) the enqueue to the HW ring fails.
If an interrupt occurs right before the lock in qat_alg_backlog_req() is
taken and the backlog queue is being emptied, then there is no request
in the HW queues that can trigger a subsequent interrupt that can clear
the backlog queue. In addition subsequent requests are enqueued to the
backlog list and not sent to the hardware.
Fix it by holding the lock while taking the decision if the request
needs to be included in the backlog queue or not. This synchronizes the
flow with the interrupt handler that drains the backlog queue.
For performance reasons, the logic has been changed to try to enqueue
first without holding the lock.
Fixes: 3868238397 ("crypto: qat - add backlog mechanism")
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Closes: https://lore.kernel.org/all/af9581e2-58f9-cc19-428f-6f18f1f83d54@redhat.com/T/
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The file adf_cfg_services.h cannot be included in header files since it
instantiates the structure adf_cfg_services. Move that structure to its
own file and export the symbol.
This does not introduce any functional change.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add the attribute `num_rps` to the `qat` attribute group. This returns
the number of ring pairs that a single device has. This allows to know
the maximum value that can be set to the attribute `rp2svc`.
Signed-off-by: Ciunas Bennett <ciunas.bennett@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add the attribute `rp2svc` to the `qat` attribute group. This provides a
way for a user to query a specific ring pair for the type of service
that is currently configured for.
When read, the service will be returned for the defined ring pair.
When written to this value will be stored as the ring pair to return
the service of.
Signed-off-by: Ciunas Bennett <ciunas.bennett@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add an interface for the rate limiting feature which allows to add,
remove and modify a QAT SLA (Service Level Agreement).
This adds a new sysfs attribute group, `qat_rl`, which can be accessed
from /sys/bus/pci/devices/<BUS:DEV:FUNCTION> with the following
hierarchy:
|-+ qat_rl
|---- id (RW) # SLA identifier
|---- cir (RW) # Committed Information Rate
|---- pir (RW) # Peak Information Rate
|---- srv (RW) # Service to be rate limited
|---- rp (RW) (HEX) # Ring pairs to be rate limited
|---- cap_rem (RW) # Remaining capability for a service
|---- sla_op (WO) # Allows to perform an operation on an SLA
The API works by setting the appropriate RW attributes and then
issuing a command through the `sla_op`. For example, to create an SLA, a
user needs to input the necessary data into the attributes cir, pir, srv
and rp and then write into `sla_op` the command `add` to execute the
operation.
The API also provides `cap_rem` attribute to get information about
the remaining device capability within a certain service which is
required when setting an SLA.
Signed-off-by: Ciunas Bennett <ciunas.bennett@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The Rate Limiting (RL) feature allows to control the rate of requests
that can be submitted on a ring pair (RP). This allows sharing a QAT
device among multiple users while ensuring a guaranteed throughput.
The driver provides a mechanism that allows users to set policies, that
are programmed to the device. The device is then enforcing those policies.
Configuration of RL is accomplished through entities called SLAs
(Service Level Agreement). Each SLA object gets a unique identifier
and defines the limitations for a single service across up to four
ring pairs (RPs count allocated to a single VF).
The rate is determined using two fields:
* CIR (Committed Information Rate), i.e., the guaranteed rate.
* PIR (Peak Information Rate), i.e., the maximum rate achievable
when the device has available resources.
The rate values are expressed in permille scale i.e. 0-1000.
Ring pair selection is achieved by providing a 64-bit mask, where
each bit corresponds to one of the ring pairs.
This adds an interface and logic that allow to add, update, retrieve
and remove an SLA.
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The QAT firmware provides a mechanism to retrieve its capabilities
through the init admin interface.
Add logic to retrieve the firmware capability mask from the firmware
through the init/admin channel. This mask reports if the
power management, telemetry and rate limiting features are supported.
The fw capabilities are stored in the accel_dev structure and are used
to detect if a certain feature is supported by the firmware loaded
in the device.
This is supported only by devices which have an admin AE.
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Some enums use the macro BIT. Include bits.h as it is missing.
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The admin API is growing and deserves its own include.
Move it from adf_common_drv.h to adf_admin.h.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The 4xxx drivers hardcode the ring to service mapping. However, when
additional configurations where added to the driver, the mappings were
not updated. This implies that an incorrect mapping might be reported
through pfvf for certain configurations.
Add an algorithm that computes the correct ring to service mapping based
on the firmware loaded on the device.
Fixes: 0cec19c761 ("crypto: qat - add support for compression for 4xxx")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add logic to count correctable, non fatal and fatal error for QAT GEN4
devices.
These counters are reported through sysfs attributes in the group
qat_ras.
Signed-off-by: Shashank Gupta <shashank.gupta@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Introduce ras counters interface for counting QAT specific device
errors and expose them through the newly created qat_ras sysfs
group attribute.
This adds the following attributes:
- errors_correctable: number of correctable errors
- errors_nonfatal: number of uncorrectable non fatal errors
- errors_fatal: number of uncorrectable fatal errors
- reset_error_counters: resets all counters
These counters are initialized during device bring up and cleared
during device shutdown and are applicable only to QAT GEN4 devices.
Signed-off-by: Shashank Gupta <shashank.gupta@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add logic to detect, report and handle uncorrectable errors reported
through the ERRSOU3 register in QAT GEN4 devices.
Signed-off-by: Shashank Gupta <shashank.gupta@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add the function adf_get_aram_base() which allows to return the
base address of the aram bar.
Signed-off-by: Shashank Gupta <shashank.gupta@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add logic to detect, report and handle correctable and uncorrectable
errors related to the compression hardware.
These are detected through the EXPRPSSMXLT, EXPRPSSMCPR and EXPRPSSMDCPR
registers.
Signed-off-by: Shashank Gupta <shashank.gupta@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add logic to detect, report and handle uncorrectable errors reported
through the ERRSOU2 register in QAT GEN4 devices.
Signed-off-by: Shashank Gupta <shashank.gupta@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add logic to detect and report uncorrectable errors reported through
the ERRSOU1 register in QAT GEN4 devices.
This also introduces the adf_dev_err_mask structure as part of
adf_hw_device_data which will allow to provide different error masks
per device generation.
Signed-off-by: Shashank Gupta <shashank.gupta@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add logic to detect and report correctable errors in QAT GEN4
devices.
This includes (1) enabling, disabling and handling error reported
through the ERRSOU0 register and (2) logic to log the errors
in the system log.
Signed-off-by: Shashank Gupta <shashank.gupta@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add infrastructure for enabling, disabling and reporting errors in the QAT
driver. This adds a new structure, adf_ras_ops, to adf_hw_device_data that
contains the following methods:
- enable_ras_errors(): allows to enable RAS errors at device
initialization.
- disable_ras_errors(): allows to disable RAS errors at device shutdown.
- handle_interrupt(): allows to detect if there is an error and report if
a reset is required. This is executed immediately after the error is
reported, in the context of an ISR.
An initial, empty, implementation of the methods above is provided
for QAT GEN4.
Signed-off-by: Shashank Gupta <shashank.gupta@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is no need to free the reset_data structure if the recovery is
unsuccessful and the reset is synchronous. The function
adf_dev_aer_schedule_reset() handles the cleanup properly. Only
asynchronous resets require such structure to be freed inside the reset
worker.
Fixes: d8cba25d2c ("crypto: qat - Intel(R) QAT driver framework")
Signed-off-by: Svyatoslav Pankratov <svyatoslav.pankratov@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The Compress and Verify (CnV) feature check and ensures data integrity
in the compression operation. The implementation of CnV keeps a record
of the CnV errors that have occurred since the driver was loaded.
Expose CnV error stats by providing the "cnv_errors" file under
debugfs. This includes the number of errors detected up to now and
the type of the last error. The error count is provided on a per
Acceleration Engine basis and it is reset every time the driver is loaded.
Signed-off-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
QAT devices implement a mechanism that allows them to go autonomously
to a low power state depending on the load.
Expose power management info by providing the "pm_status" file under
debugfs. This includes PM state, PM event log, PM event counters, PM HW
CSRs, per-resource type constrain counters and per-domain power gating
status specific to the QAT device.
This information is retrieved from (1) the FW by means of
ICP_QAT_FW_PM_INFO command, (2) CSRs and (3) counters collected by the
device driver.
In addition, add logic to keep track and report power management event
interrupts and acks/nacks sent to FW to allow/prevent state transitions.
Signed-off-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Include kernel.h for GENMASK(), kstrtobool() and types.
Add forward declaration for struct adf_accel_dev. Remove unneeded
include.
This change doesn't introduce any function change.
Signed-off-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Create CRYPTO_QAT namespace for symbols exported by the qat_common
module and import those in the QAT drivers. It will reduce the global
namespace crowdedness and potential misuse or the API.
This does not introduce any functional change.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove the implementation of zlib-deflate because it is completely
unused in the kernel.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct adf_fw_counters.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Tom Rix <trix@redhat.com>
Cc: Adam Guerin <adam.guerin@intel.com>
Cc: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: qat-linux@intel.com
Cc: linux-crypto@vger.kernel.org
Cc: llvm@lists.linux.dev
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Increase the size of the buffers used for composing the names used for
the transport debugfs entries and the vector name to avoid a potential
truncation.
This resolves the following errors when compiling the driver with W=1
and KCFLAGS=-Werror on GCC 12.3.1:
drivers/crypto/intel/qat/qat_common/adf_transport_debug.c: In function ‘adf_ring_debugfs_add’:
drivers/crypto/intel/qat/qat_common/adf_transport_debug.c💯60: error: ‘snprintf’ output may be truncated before the last format character [-Werror=format-truncation=]
drivers/crypto/intel/qat/qat_common/adf_isr.c: In function ‘adf_isr_resource_alloc’:
drivers/crypto/intel/qat/qat_common/adf_isr.c:197:47: error: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size between 0 and 5 [-Werror=format-truncation=]
Fixes: a672a9dc87 ("crypto: qat - Intel(R) QAT transport code")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
QAT GEN4 devices support chained compression operations. These
allow, with a single request to firmware, to hash then compress
data.
Extend the configuration to enable such mode. The cfg_services
operations in sysfs are extended to allow the string "dcc". When
selected, the driver downloads to the device both the symmetric
crypto and the compression firmware images and sends an admin message
to firmware which enables `chained` operations.
In addition, it sets the device's capabilities as the combination
of compression and symmetric crypto capabilities, while excluding
the ICP_ACCEL_CAPABILITIES_CRYPTO_SYMMETRIC bit to indicate
that in this mode, symmetric crypto instances are not supported.
When "dcc" is enabled, the device will handle compression requests
as if the "dc" configuration is loaded ("dcc" is a variation of "dc")
and the driver will register the acomp algorithms.
As for the other extended configurations, "dcc" is only available for
qat_4xxx devices and the chaining service will be only accessible from
user space.
Signed-off-by: Adam Guerin <adam.guerin@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The data structure that associates a service id with its name is
replicated across the driver.
Remove duplication by moving this data structure to a new include file,
adf_cfg_services.h in order to have consistency across the drivers.
Note that the data structure is re-instantiated every time the new
include is added to a compilation unit.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The function adf_dev_init(), through the subsystem qat_compression,
populates the list of list of compression instances
accel_dev->compression_list. If the list of instances is not empty,
the function adf_dev_start() will then call qat_compression_registers()
register the compression algorithms into the crypto framework.
If any of the functions in adf_dev_start() fail, the caller of such
function, in the error path calls adf_dev_down() which in turn call
adf_dev_stop() and adf_dev_shutdown(), see for example the function
state_store in adf_sriov.c.
However, if the registration of compression algorithms is not done,
adf_dev_stop() will try to unregister the algorithms regardless.
This might cause the counter active_devs in qat_compression.c to get
to a negative value.
Add a new state, ADF_STATUS_COMPRESSION_ALGS_REGISTERED, which tracks
if the compression algorithms are registered into the crypto framework.
Then use this to unregister the algorithms if such flag is set. This
ensures that the compression algorithms are only unregistered if
previously registered.
Fixes: 1198ae56c9 ("crypto: qat - expose deflate through acomp api for QAT GEN2")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The function adf_dev_init(), through the subsystem qat_crypto, populates
the list of list of crypto instances accel_dev->crypto_list.
If the list of instances is not empty, the function adf_dev_start() will
then call qat_algs_registers() and qat_asym_algs_register() to register
the crypto algorithms into the crypto framework.
If any of the functions in adf_dev_start() fail, the caller of such
function, in the error path calls adf_dev_down() which in turn call
adf_dev_stop() and adf_dev_shutdown(), see for example the function
state_store in adf_sriov.c.
However, if the registration of crypto algorithms is not done,
adf_dev_stop() will try to unregister the algorithms regardless.
This might cause the counter active_devs in qat_algs.c and
qat_asym_algs.c to get to a negative value.
Add a new state, ADF_STATUS_CRYPTO_ALGS_REGISTERED, which tracks if the
crypto algorithms are registered into the crypto framework. Then use
this to unregister the algorithms if such flag is set. This ensures that
the crypto algorithms are only unregistered if previously registered.
Fixes: d8cba25d2c ("crypto: qat - Intel(R) QAT driver framework")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If the device is already in the up state, a subsequent write of `up` to
the sysfs attribute /sys/bus/pci/devices/<BDF>/qat/state brings the
device down.
Fix this behaviour by ignoring subsequent `up` commands if the device is
already in the up state.
Fixes: 1bdc85550a ("crypto: qat - fix concurrency issue when device state changes")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Do not shadow the return code from adf_dev_down() in the error path of
the DEV_DOWN command.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit 1bdc85550a ("crypto: qat - fix concurrency issue when device
state changes") introduced the function adf_dev_down() which wraps the
functions adf_dev_stop() and adf_dev_shutdown().
In a subsequent change, the sequence adf_dev_stop() followed by
adf_dev_shutdown() was then replaced across the driver with just a call
to the function adf_dev_down().
The functions adf_dev_stop() and adf_dev_shutdown() are called in error
paths to stop the accelerator and free up resources and can be called
even if the counterparts adf_dev_init() and adf_dev_start() did not
complete successfully.
However, the implementation of adf_dev_down() prevents the stop/shutdown
sequence if the device is found already down.
For example, if adf_dev_init() fails, the device status is not set as
started and therefore a call to adf_dev_down() won't be calling
adf_dev_shutdown() to undo what adf_dev_init() did.
Do not check if a device is started in adf_dev_down() but do the
equivalent check in adf_sysfs.c when handling a DEV_DOWN command from
the user.
Fixes: 2b60f79c7b ("crypto: qat - replace state machine calls")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Convert list_for_each() to list_for_each_entry() so that the list_itr
list_head pointer and list_entry() call are no longer needed, which
can reduce a few lines of code. No functional changed.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When extending the capability detection logic for 4xxx devices the
SMx algorithms were accidentally missed.
Enable these SMx capabilities by default for QAT GEN4 devices.
Check for device variants where the SMx algorithms are explicitly
disabled by the GEN4 hardware. This is indicated in fusectl1
register.
Mask out SM3 and SM4 based on a bit specific to those algorithms.
Mask out SM2 if the PKE slice is not present.
Fixes: 4b44d28c71 ("crypto: qat - extend crypto capability detection for 4xxx")
Signed-off-by: Adam Guerin <adam.guerin@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use kfree_sensitive() instead of memset() and kfree().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Mark UWORD_CPYBUF_SIZE with U suffix to make its type the same
with words_num. Then replace the if statement with min() in
qat_uclo_wr_uimage_raw_page() to make code shorter.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: You Kangren <youkangren@vivo.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
A firmware update for QAT GEN2 changed the format of a data
structure used to report the heartbeat counters.
To support all firmware versions, extend the heartbeat logic
with an algorithm that detects the number of counters returned
by firmware. The algorithm detects the number of counters to
be used (and size of the corresponding data structure) by the
comparison the expected size of the data in memory, with the data
which was written by the firmware.
Firmware detection is done one time during the first read of heartbeat
debugfs file to avoid increasing the time needed to load the module.
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Under some circumstances, firmware in the QAT devices could become
unresponsive. The Heartbeat feature provides a mechanism to detect
unresponsive devices.
The QAT FW periodically writes to memory a set of counters that allow
to detect the liveness of a device. This patch adds logic to enable
the reporting of those counters, analyze them and report if a device
is alive or not.
In particular this adds
(1) heartbeat enabling, reading and detection logic
(2) reporting of heartbeat status and configuration via debugfs
(3) documentation for the newly created sysfs entries
(4) configuration of FW settings related to heartbeat, e.g. tick period
(5) logic to convert time in ms (provided by the user) to clock ticks
This patch introduces a new folder in debugfs called heartbeat with the
following attributes:
- status
- queries_sent
- queries_failed
- config
All attributes except config are reading only. In particular:
- `status` file returns 0 when device is operational and -1 otherwise.
- `queries_sent` returns the total number of heartbeat queries sent.
- `queries_failed` returns the total number of heartbeat queries failed.
- `config` allows to adjust the frequency at which the firmware writes
counters to memory. This period is given in milliseconds and it is
fixed for GEN4 devices.
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The QAT hardware does not expose a mechanism to report its clock
frequency. This is required to implement the Heartbeat feature.
Add a clock measuring algorithm that estimates the frequency by
comparing the internal timestamp counter incremented by the firmware
with the time measured by the kernel.
The frequency value is only used internally and not exposed to
the user.
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Drop legacy heartbeat interface from FW API as it is no longer used.
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The power management feature in QAT 4xxx devices can disable clock
sources used to implement timers. Because of that, the firmware needs to
get an external reliable source of time.
Add a kernel delayed work that periodically sends an event to the
firmware. This is triggered every 200ms. At each execution, the driver
sends a sync request to the firmware reporting the current timestamp
counter value.
This is a pre-requisite for enabling the heartbeat, telemetry and
rate limiting features.
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Expose FW counters statistics by providing the "fw_counters" file
under debugfs. Currently the statistics include the number of
requests sent to the FW and the number of responses received
from the FW for each Acceleration Engine, for all the QAT product
line.
This patch is based on earlier work done by Marco Chiappero.
Co-developed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The power management configuration of 4xxx devices is too aggressive
and in some conditions the device might be prematurely put to a low
power state.
Increase the idle filter value to prevent that.
In future, this will be set by firmware.
Fixes: e5745f3411 ("crypto: qat - enable power management for QAT GEN4")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The function adf_init_admin_pm() is not used outside of the intel_qat
module.
Do not export it.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Expose 'pm_idle_enabled' sysfs attribute. This attribute controls how
idle conditions are handled. If it is set to 1 (idle support enabled)
when the device detects an idle condition, the driver will transition
the device to the 'MIN' power configuration.
In order to set the value of this attribute for a device, the device
must be in the 'down' state.
This only applies to qat_4xxx generation.
Signed-off-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
A QAT GEN4 device can be currently configured for crypto (sym;asym) or
compression (dc).
This patch extends the configuration to support more variations of these
services, download the correct FW images on the device and report the
correct capabilities on the device based on the configured service.
The device can now be configured with the following services:
"sym", "asym", "dc", "sym;asym", "asym;sym", "sym;dc", "dc;sym",
"asym;dc", "dc;asym".
With this change, the configuration "sym", "asym", "sym;dc", "dc;sym",
"asym;dc", "dc;asym" will be accessible only via userspace, i.e. the driver
for those configurations will not register into the crypto framework.
Support for such configurations in kernel will be enabled in a later
patch.
The pairs "sym;asym" and "asym;sym" result in identical device config.
As do "sym;dc", "dc;sym", and "asym;dc", "dc;asym".
Signed-off-by: Adam Guerin <adam.guerin@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Update fw image names to be constant throughout the driver.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Make use of the default statements by changing the pattern:
switch(condition) {
case COND_A:
...
break;
case COND_b:
...
break;
}
return ret;
in
switch(condition) {
case COND_A:
...
break;
case COND_b:
...
break;
default:
return ret;
}
Signed-off-by: Adam Guerin <adam.guerin@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The callback function for RSA frees the memory allocated for the source
and destination buffers before unmapping them.
This sequence is wrong.
Change the cleanup sequence to unmap the buffers before freeing them.
Fixes: 3dfaf0071e ("crypto: qat - remove dma_free_coherent() for RSA")
Signed-off-by: Hareshx Sankar Raj <hareshx.sankar.raj@intel.com>
Co-developed-by: Bolemx Sivanagaleela <bolemx.sivanagaleela@intel.com>
Signed-off-by: Bolemx Sivanagaleela <bolemx.sivanagaleela@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The callback function for DH frees the memory allocated for the
destination buffer before unmapping it.
This sequence is wrong.
Change the cleanup sequence to unmap the buffer before freeing it.
Fixes: 029aa4624a ("crypto: qat - remove dma_free_coherent() for DH")
Signed-off-by: Hareshx Sankar Raj <hareshx.sankar.raj@intel.com>
Co-developed-by: Bolemx Sivanagaleela <bolemx.sivanagaleela@intel.com>
Signed-off-by: Bolemx Sivanagaleela <bolemx.sivanagaleela@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The LZS and RAND features are no longer available on QAT.
Remove the definition of bit 6 (LZS) and bit 7 (RAND) in the enum that
represents the capabilities and replace them with a comment mentioning
that those bits are reserved.
Those bits shall not be used in future.
Signed-off-by: Karthikeyan Gopal <karthikeyan.gopal@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The function adf_dbgfs_exit() was improperly named causing the build to
fail when CONFIG_DEBUG_FS=n.
Rename adf_dbgfs_cleanup() as adf_dbgfs_exit().
This fixes the following build error:
CC [M] drivers/crypto/intel/qat/qat_c62x/adf_drv.o
drivers/crypto/intel/qat/qat_c62x/adf_drv.c: In function ‘adf_cleanup_accel’:
drivers/crypto/intel/qat/qat_c62x/adf_drv.c:69:9: error: implicit declaration of function ‘adf_dbgfs_exit’; did you mean ‘adf_dbgfs_init’? [-Werror=implicit-function-declaration]
69 | adf_dbgfs_exit(accel_dev);
| ^~~~~~~~~~~~~~
| adf_dbgfs_init
cc1: all warnings being treated as errors
make[2]: *** [scripts/Makefile.build:252: drivers/crypto/intel/qat/qat_c62x/adf_drv.o] Error 1
make[1]: *** [scripts/Makefile.build:494: drivers/crypto/intel/qat/qat_c62x] Error 2
make: *** [Makefile:2026: drivers/crypto/intel/qat] Error 2
Fixes: 9260db6640 ("crypto: qat - move dbgfs init to separate file")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202306030654.5t4qkyN1-lkp@intel.com/
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move initialization of debugfs entries to a separate file.
This simplifies the exclusion of the debugfs logic in the QAT driver
when the kernel is built with CONFIG_DEBUG_FS=n.
In addition, it will allow to consolidate the addition of debugfs
entries to a single location in the code.
This implementation adds infrastructure to create (and remove) debugfs
entries at two different stages. The first, done when a device is probed,
allows to keep debugfs entries persistent between a transition in device
state (up to down or vice versa). The second, done after the initialization
phase, allows to have debugfs entries that are accessible only when
the device is up.
In addition, move the creation of debugfs entries for configuration
to the newly created function adf_dbgfs_init() and replace symbolic
permissions with octal permissions when creating the debugfs files.
This is to resolve the following warning reported by checkpatch:
WARNING: Symbolic permissions 'S_IRUSR' are not preferred. Consider using octal permissions '0400'.
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening in
the driver core in the quest to be able to move "struct bus" and "struct
class" into read-only memory, a task now complete with these changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules for
all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most of
them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp7Sw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykitQCfamUHpxGcKOAGuLXMotXNakTEsxgAoIquENm5
LEGadNS38k5fs+73UaxV
=7K4B
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening
in the driver core in the quest to be able to move "struct bus" and
"struct class" into read-only memory, a task now complete with these
changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules
for all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most
of them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (120 commits)
device property: make device_property functions take const device *
driver core: update comments in device_rename()
driver core: Don't require dynamic_debug for initcall_debug probe timing
firmware_loader: rework crypto dependencies
firmware_loader: Strip off \n from customized path
zram: fix up permission for the hot_add sysfs file
cacheinfo: Add use_arch[|_cache]_info field/function
arch_topology: Remove early cacheinfo error message if -ENOENT
cacheinfo: Check cache properties are present in DT
cacheinfo: Check sib_leaf in cache_leaves_are_shared()
cacheinfo: Allow early level detection when DT/ACPI info is missing/broken
cacheinfo: Add arm64 early level initializer implementation
cacheinfo: Add arch specific early level initializer
tty: make tty_class a static const structure
driver core: class: remove struct class_interface * from callbacks
driver core: class: mark the struct class in struct class_interface constant
driver core: class: make class_register() take a const *
driver core: class: mark class_release() as taking a const *
driver core: remove incorrect comment for device_create*
MIPS: vpe-cmp: remove module owner pointer from struct class usage.
...
With the growing number of Intel crypto drivers, it makes sense to
group them all into a single drivers/crypto/intel/ directory.
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
