Because the permission on the VF debugfs file is "0444". So
the VF function checking is redundant in qos writing api.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The pci bdf number check is added for qos written by using the pci api.
Directly get the devfn by pci_dev, so delete some redundant code.
And use the kstrtoul instead of sscanf to simplify code.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Increase the buffer to prevent stack overflow by fuzz test. The maximum
length of the qos configuration buffer is 256 bytes. Currently, the value
of the 'val buffer' is only 32 bytes. The sscanf does not check the dest
memory length. So the 'val buffer' may stack overflow.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
After the device is reset, the VF needs to re-enable communication
interrupt before the VF sends restart complete message to the PF.
If the interrupt is re-enabled after the VF notifies the PF, the PF
may fail to send messages to the VF after receiving VF's restart
complete message.
Fixes: 760fe22cf5 ("crypto: hisilicon/qm - update reset flow")
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In qm_get_xqc_depth(), parameters low_bits and high_bits save
the values of the corresponding bits. However, the values saved by the
two parameters are opposite. As a result, the values returned to the
callers are incorrect.
Fixes: 129a9f3401 ("crypto: hisilicon/qm - get qp num and depth from hardware registers")
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
dev_to_node() can handle the case when CONFIG_NUMA is not set, so the
check of CONFIG_NUMA is redundant and can be removed.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The default qos value is not initialized when sriov is repeatedly enabled
and disabled. So add the vf qos value initialized in the sriov enable
process.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The value of qm algorithm can change dynamically according to the
value of the capability register.
Add xxx_set_qm_algs() function to obtain the algs that the
hardware device supported from the capability register and set
them into usr mode attribute files.
Signed-off-by: Zhiqi Song <songzhiqi1@huawei.com>
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Support get device irq information from hardware registers
instead of fixed macros.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Hardware V3 and later versions support get error type from
registers. To be compatible with later hardware versions,
get error type from registers instead of fixed marco.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
To be compatible with accelerator devices of different
versions, 'UACCE_CMD_QM_SET_QP_INFO' ioctl is added to obtain
queue information in userspace, including queue depth and buffer
description size.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Hardware V3 and later versions can obtain qp num and depth supported
by the hardware from registers. To be compatible with later hardware
versions, get qp num and depth from registers instead of fixed marcos.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Before hardware V3, hardwares do not provide the feature registers,
driver resolves hardware differences based on the hardware version.
As a result, the driver does not support the new hardware.
Hardware V3 and later versions support to obtain hardware features,
such as power-gating management and doorbell isolation, through
the hardware registers. To be compatible with later hardware versions,
the features of the current device is obtained by reading the
hardware registers instead of the hardware version.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The accelerator drivers supports users to enable VFs through the
module parameter 'vfs_num'. If the number of VFs to be enabled
exceeds the total VFs, all VFs are enabled. Change it to the same
as enabling VF through the 'sriov_numvfs' file. Returns -ERANGE
if the number of VFs to be enabled exceeds total VFs.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In function qm_cmd_write(), if function returns from
branch 'atomic_read(&qm->status.flags) == QM_STOP',
the got dfx access is forgotten to put.
Fixes: 607c191b37 ("crypto: hisilicon - support runtime PM for accelerator device")
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
After the mailbox operation is complete, the result may be unsuccessful.
It needs to check the status bits of the mailbox register,
if it fails, -EIO is returned.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Judgment should not be added in the back process. So clean it.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Data in the hardware cache needs to be written back to the memory
before the queue memory is released. Currently, the queue memory is
applied for when the driver is loaded and released when the driver is
removed. Therefore, the hardware cache does not need to be written back
when process puts queue.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The dump_show() is used to output hardware information for error locating.
It is not need to apply for memory to temporarily store the converted data.
It can directly output the data. Therefore, remove some unnecessary code.
Signed-off-by: Junchong Pan <panjunchong@hisilicon.com>
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In the function hisi_qm_memory_init(), if resource alloc fails after
idr_init, the initialized qp_idr needs to be destroyed.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Calls to pci_cleanup_aer_uncorrect_error_status() have already been
removed after commit 62b36c3ea6 ("PCI/AER: Remove
pci_cleanup_aer_uncorrect_error_status() calls"). But in commit
6c6dd5802c ("crypto: hisilicon/qm - add controller reset interface")
pci_aer_clear_nonfatal_status() was used again, so remove it in
this patch.
note: pci_cleanup_aer_uncorrect_error_status() was renamed to
pci_aer_clear_nonfatal_status() in commit 894020fdd8
("PCI/AER: Rationalize error status register clearing")
Signed-off-by: Zhuo Chen <chenzhuo.1@bytedance.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When the driver receives an event interrupt, the driver will enable
the event interrupt after handling all completed tasks on the function,
tasks on the function are parsed through only one thread. If the task's
user callback takes time, other tasks on the function will be blocked.
Therefore, the event irq processing is modified as follows:
1. Obtain the ID of the queue that completes the task.
2. Enable event interrupt.
3. Parse the completed tasks in the queue and call the user callback.
Enabling event interrupt in advance can quickly report pending event
interrupts and process tasks in multiple threads.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Before stopping the function, the driver needs to flush all the remaining
work about event irq. Therefore, accelerator drivers use a private
workqueue(qm->wq) to handle event irq instead of the system workqueue.
This patch moves alloc workqueue from sec_main.c and zip_main.c to qm.c.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The resources allocated by hisi_qm_memory_init() are released by
hisi_qm_uninit(). Add hisi_qm_memory_uninit() to release resources,
no functional change.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
hisi_qm_get_free_qp_num() is to get the free queue number on the function.
It is a simple function and is only called by
hisi_qm_get_available_instances().
This patch modifies to get the free queue directly in
hisi_qm_get_available_instances(), and remove hisi_qm_get_free_qp_num().
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
hisi_qm_free_qps() can release multiple queues in one call, and it is
already exported. So, replace hisi_qm_release_qp() with hisi_qm_free_qps()
in zip_crypto.c, and do not export hisi_qm_release_qp() outside qm.c.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
These functions 'hisi_qm_create_qp' and 'hisi_qm_set_vft' are not
used outside qm.c, so they are marked as static.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add last word dumping function during acc engines controller reset.
The last words are reported to the printed information during the
reset. The dmesg information included qm debugging registers and
engine debugging registers. It can help to improve debugging
capability.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add register detection function to accelerator. Provided a tool that
user can checking differential register through Debugfs.
e.g.
cd /sys/kernel/debug/hisi_zip/<bdf>/zip_dfx
cat diff_regs
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
A 'dma_wmb' barrier is enough to guarantee previous writes
before accessing by acc device in the outer shareable domain.
A 'smp_wmb' barrier is enough to guarantee previous writes
before accessing by other cpus in the inner shareble domain.
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
- Introduce new device migration uAPI and implement device specific
mlx5 vfio-pci variant driver supporting new protocol (Jason Gunthorpe,
Yishai Hadas, Leon Romanovsky)
- New HiSilicon acc vfio-pci variant driver, also supporting migration
interface (Shameer Kolothum, Longfang Liu)
- D3hot fixes for vfio-pci-core (Abhishek Sahu)
- Document new vfio-pci variant driver acceptance criteria
(Alex Williamson)
- Fix UML build unresolved ioport_{un}map() functions
(Alex Williamson)
- Fix MAINTAINERS due to header movement (Lukas Bulwahn)
-----BEGIN PGP SIGNATURE-----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=Sv96
-----END PGP SIGNATURE-----
Merge tag 'vfio-v5.18-rc1' of https://github.com/awilliam/linux-vfio
Pull VFIO updates from Alex Williamson:
- Introduce new device migration uAPI and implement device specific
mlx5 vfio-pci variant driver supporting new protocol (Jason
Gunthorpe, Yishai Hadas, Leon Romanovsky)
- New HiSilicon acc vfio-pci variant driver, also supporting migration
interface (Shameer Kolothum, Longfang Liu)
- D3hot fixes for vfio-pci-core (Abhishek Sahu)
- Document new vfio-pci variant driver acceptance criteria
(Alex Williamson)
- Fix UML build unresolved ioport_{un}map() functions
(Alex Williamson)
- Fix MAINTAINERS due to header movement (Lukas Bulwahn)
* tag 'vfio-v5.18-rc1' of https://github.com/awilliam/linux-vfio: (31 commits)
vfio-pci: Provide reviewers and acceptance criteria for variant drivers
MAINTAINERS: adjust entry for header movement in hisilicon qm driver
hisi_acc_vfio_pci: Use its own PCI reset_done error handler
hisi_acc_vfio_pci: Add support for VFIO live migration
crypto: hisilicon/qm: Set the VF QM state register
hisi_acc_vfio_pci: Add helper to retrieve the struct pci_driver
hisi_acc_vfio_pci: Restrict access to VF dev BAR2 migration region
hisi_acc_vfio_pci: add new vfio_pci driver for HiSilicon ACC devices
hisi_acc_qm: Move VF PCI device IDs to common header
crypto: hisilicon/qm: Move few definitions to common header
crypto: hisilicon/qm: Move the QM header to include/linux
vfio/mlx5: Fix to not use 0 as NULL pointer
PCI/IOV: Fix wrong kernel-doc identifier
vfio/mlx5: Use its own PCI reset_done error handler
vfio/pci: Expose vfio_pci_core_aer_err_detected()
vfio/mlx5: Implement vfio_pci driver for mlx5 devices
vfio/mlx5: Expose migration commands over mlx5 device
vfio: Remove migration protocol v1 documentation
vfio: Extend the device migration protocol with RUNNING_P2P
vfio: Define device migration protocol v2
...
We use VF QM state register to record the status of the QM configuration
state. This will be used in the ACC migration driver to determine whether
we can safely save and restore the QM data.
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Acked-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Link: https://lore.kernel.org/r/20220308184902.2242-8-shameerali.kolothum.thodi@huawei.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Move Doorbell and Mailbox definitions to common header file.
Also export QM mailbox functions.
This will be useful when we introduce VFIO PCI HiSilicon ACC live
migration driver.
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Acked-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Link: https://lore.kernel.org/r/20220308184902.2242-3-shameerali.kolothum.thodi@huawei.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Since we are going to introduce VFIO PCI HiSilicon ACC driver for live
migration in subsequent patches, move the ACC QM header file to a
common include dir.
Acked-by: Zhou Wang <wangzhou1@hisilicon.com>
Acked-by: Longfang Liu <liulongfang@huawei.com>
Acked-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Link: https://lore.kernel.org/r/20220308184902.2242-2-shameerali.kolothum.thodi@huawei.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Due to that extra page addr is used as a qp error flag when the device
resetting. So it not should to clear this qp flag in userspace.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The kernel test rebot report this warning: Uninitialized variable: ret.
The code flow may return value of ret directly. This value is an
uninitialized variable, here is fix it.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Building with clang static analysis returns this warning:
qm.c:4382:11: warning: The left operand of '==' is a garbage value
if (*val == 0 || *val > QM_QOS_MAX_VAL || ret) {
~~~~ ^
The call to qm_qos_value_init() can return an error without setting
*val. So check ret before checking *val.
Fixes: 72b010dc33 ("crypto: hisilicon/qm - supports writing QoS int the host")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For Kunpeng930, if qm clock-gating is enabled, rate limiter
will be inaccurate. Therefore, disable clock-gating before doing task.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If the hardware reports the 'CQ' overflow or 'CQE' error by the abnormal
interrupt, disable the queue and stop tasks send to hardware.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If the hardware reports the event queue overflow by the abnormal interrupt,
the driver needs to reset the function and re-enable the event queue
interrupt and abnormal interrupt.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The abnormal interrupt method needs to be changed, and the changed method
needs to be locked in order to maintain atomicity. Therefore,
replace request_irq() with request_threaded_irq().
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
After processing an interrupt event and the interrupt function is
enabled by writing the QM_DOORBELL_CMD_AEQ register, the hardware
may generate new interrupt events due to processing other user's task
when the subsequent interrupt events have not been processed. The new
interrupt event will disrupt the current normal processing flow and
cause other problems.
Therefore, the operation of writing the QM_DOORBELL_CMD_AEQ doorbell
register needs to be placed after all interrupt events processing
are completed.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch does not change any code, just code movement. Preparing for
next patch.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The internal memory of the device needs to be reset only when
the device is globally initialized. Other scenarios, such as
function reset, do not need to perform reset.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When remove the driver and executing the task occur at the same time,
the following deadlock will be triggered:
Chain exists of:
sva_lock --> uacce_mutex --> &qm->qps_lock
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&qm->qps_lock);
lock(uacce_mutex);
lock(&qm->qps_lock);
lock(sva_lock);
And the lock 'qps_lock' is used to protect qp. Therefore, it's reasonable
cycle is to continue until the qp memory is released. So move the release
lock infront of 'uacce_remove'.
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When hisi_qm_resume() returns 0, it indicates that the device has started
successfully. If the device fails to start, hisi_qm_resume() needs to
return the actual error code to the caller instead of 0.
Fixes: d7ea53395b ("crypto: hisilicon - add runtime PM ops")
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Some optimize for the calculation of qos shaper parameters.
and modify the comments.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
1. Optimize overly long functions.
2. Fix the format symbol does not match the actual type.
3. Use the PCI_DEVFN to get the function id.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The value of qos should be reset after flr resetting or device
resetting. So set the max of qos value for every function. Then
update the value of qos when user writing the alg_qos.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
-----BEGIN PGP SIGNATURE-----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=nsMh
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Conserve IRQs by setting up portdrv IRQs only when there are users
(Jan Kiszka)
- Rework and simplify _OSC negotiation for control of PCIe features
(Joerg Roedel)
- Remove struct pci_dev.driver pointer since it's redundant with the
struct device.driver pointer (Uwe Kleine-König)
Resource management:
- Coalesce contiguous host bridge apertures from _CRS to accommodate
BARs that cover more than one aperture (Kai-Heng Feng)
Sysfs:
- Check CAP_SYS_ADMIN before parsing user input (Krzysztof
Wilczyński)
- Return -EINVAL consistently from "store" functions (Krzysztof
Wilczyński)
- Use sysfs_emit() in endpoint "show" functions to avoid buffer
overruns (Kunihiko Hayashi)
PCIe native device hotplug:
- Ignore Link Down/Up caused by resets during error recovery so
endpoint drivers can remain bound to the device (Lukas Wunner)
Virtualization:
- Avoid bus resets on Atheros QCA6174, where they hang the device
(Ingmar Klein)
- Work around Pericom PI7C9X2G switch packet drop erratum by using
store and forward mode instead of cut-through (Nathan Rossi)
- Avoid trying to enable AtomicOps on VFs; the PF setting applies to
all VFs (Selvin Xavier)
MSI:
- Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
Song)
VPD:
- Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
in the possible VPD space; use these to simplify the cxgb3 driver
(Heiner Kallweit)
Peer-to-peer DMA:
- Add (not subtract) the bus offset when calculating DMA address
(Wang Lu)
ASPM:
- Re-enable LTR at Downstream Ports so they don't report Unsupported
Requests when reset or hot-added devices send LTR messages
(Mingchuang Qiao)
Apple PCIe controller driver:
- Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
Zyngier)
Cadence PCIe controller driver:
- Return success when probe succeeds instead of falling into error
path (Li Chen)
HiSilicon Kirin PCIe controller driver:
- Reorganize PHY logic and add support for external PHY drivers
(Mauro Carvalho Chehab)
- Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
Carvalho Chehab)
- Add Kirin 970 support (Mauro Carvalho Chehab)
- Make driver removable (Mauro Carvalho Chehab)
Intel VMD host bridge driver:
- If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
enabled (Adrian Huang)
- Number each controller so we can tell them apart in
/proc/interrupts (Chunguang Xu)
- Avoid building on UML because VMD depends on x86 bare metal APIs
(Johannes Berg)
Marvell Aardvark PCIe controller driver:
- Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
- Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
- Downgrade PIO Response Status messages to debug level (Marek Behún)
- Preserve CRS SV (Config Request Retry Software Visibility) bit in
emulated Root Control register (Pali Rohár)
- Fix issue in configuring reference clock (Pali Rohár)
- Don't clear status bits for masked interrupts (Pali Rohár)
- Don't mask unused interrupts (Pali Rohár)
- Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
- Retry config accesses on CRS response (Pali Rohár)
- Simplify emulated Root Capabilities initialization (Pali Rohár)
- Fix several link training issues (Pali Rohár)
- Fix link-up checking via LTSSM (Pali Rohár)
- Fix reporting of Data Link Layer Link Active (Pali Rohár)
- Fix emulation of W1C bits (Marek Behún)
- Fix MSI domain .alloc() method to return zero on success (Marek
Behún)
- Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
(Marek Behún)
- Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
at startup; PCI core will set those as necessary (Pali Rohár)
- When operating as a Root Port, set class code to "PCI Bridge"
instead of the default "Mass Storage Controller" (Pali Rohár)
- Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
implement this per spec (Pali Rohár)
- Add emulation of option ROM BAR since aardvark doesn't implement
this per spec (Pali Rohár)
MediaTek MT7621 PCIe controller driver:
- Add MediaTek MT7621 PCIe host controller driver and DT binding
(Sergio Paracuellos)
Qualcomm PCIe controller driver:
- Add SC8180x compatible string (Bjorn Andersson)
- Add endpoint controller driver and DT binding (Manivannan
Sadhasivam)
- Restructure to use of_device_get_match_data() (Prasad Malisetty)
- Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)
Renesas R-Car PCIe controller driver:
- Remove unnecessary includes (Geert Uytterhoeven)
Rockchip DesignWare PCIe controller driver:
- Add DT binding (Simon Xue)
Socionext UniPhier Pro5 controller driver:
- Serialize INTx masking/unmasking (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Run dwc .host_init() method before registering MSI interrupt
handler so we can deal with pending interrupts left by bootloader
(Bjorn Andersson)
- Clean up Kconfig dependencies (Andy Shevchenko)
- Export symbols to allow more modular drivers (Luca Ceresoli)
TI DRA7xx PCIe controller driver:
- Allow host and endpoint drivers to be modules (Luca Ceresoli)
- Enable external clock if present (Luca Ceresoli)
TI J721E PCIe driver:
- Disable PHY when probe fails after initializing it (Christophe
JAILLET)
MicroSemi Switchtec management driver:
- Return error to application when command execution fails because an
out-of-band reset has cleared the device BARs, Memory Space Enable,
etc (Kelvin Cao)
- Fix MRPC error status handling issue (Kelvin Cao)
- Mask out other bits when reading of management VEP instance ID
(Kelvin Cao)
- Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
(Kelvin Cao)
- Add check of event support (Logan Gunthorpe)
Miscellaneous:
- Remove unused pci_pool wrappers, which have been replaced by
dma_pool (Cai Huoqing)
- Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
Wilczyński)
- Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
Wilczyński)
- Fix some sscanf(), sprintf() format mismatches (Krzysztof
Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof
Wilczyński)
- Correct some misspellings (Krzysztof Wilczyński)"
* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
PCI: Add ACS quirk for Pericom PI7C9X2G switches
PCI: apple: Configure RID to SID mapper on device addition
iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
PCI: apple: Implement MSI support
PCI: apple: Add INTx and per-port interrupt support
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: apple: Set up reference clocks when probing
PCI: apple: Add initial hardware bring-up
PCI: of: Allow matching of an interrupt-map local to a PCI device
of/irq: Allow matching of an interrupt-map local to an interrupt controller
irqdomain: Make of_phandle_args_to_fwspec() generally available
PCI: Do not enable AtomicOps on VFs
...
Replace dev->driver_name() by dev_driver_string() for the corresponding
struct device. This is a step toward removing pci_dev->driver.
[bhelgaas: split to separate patch]
Link: https://lore.kernel.org/r/20211004125935.2300113-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
As qm should register to uacce in UACCE_DEV_SVA mode,
this patch modifies to checks uacce mode before doing uacce
registration.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Allocate an extra memory page for qp in the qp memory initialization.
Set a qp error flag in the extra page addr when device resetting.
This error flag can be seen in the userspace. This flag can helps
users to stop tasks when device resetting. After resetting, this error
flag will be reset when this qp is created again. So app should release
the old qp and request a new one, and do the task on the new queue
again.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Allocate an extra memory page for qp. This extra page is
used to set the device or qp status. But this page not
be used currently. Meanwhile it leads to dus size not equal
to mmap size as using uacce sva mode, and cause the app task
broken.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The function qm_qos_value_init expects an unsigned integer but
is incorrectly supplying a signed format to sscanf. This patch
fixes it.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
To support runtime PM, use the function 'pci_set_power_state' to change
the power state. Therefore, method _PS0 or _PR0 needs to be filled by
platform. So check whether the method is supported, if not, print a
prompt information.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
To avoid repeatedly obtaining 'qm' from 'filp', parameter passing of
debugfs function directly use 'qm' instead of 'filp'.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Accelerator devices support runtime PM to reduce power consumption.
This patch adds the runtime PM suspend/resume callbacks to the
accelerator devices.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The accelerator devices support runtime PM, when device is in suspended, an
exception will occur if reading registers. Therefore, this patch uses
'debugfs_create_file' instead of 'debugfs_create_regset32' to create
debugfs file, and then the driver can get the device status before
reading the register.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds a function hisi_qm_is_q_updated to
check if the task is ready in hardware queue when
user polls an UACCE queue.This prevents users from
repeatedly querying whether the accelerator has
completed tasks, which wastes CPU resources.
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
1. The ACC driver supports to inquiry each function's QoS in the Host
and VM. The driver supports reading QoS by the device debug SysFS
attribute file "alg_qos", like "cat alg_qos".
2. Modify the communication process between pf and vf as needed.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
According to the function communication, add pf ping single
vf function to be used in the vf read QoS.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Merges the work initialization process into a single function from
qm initialization.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
1. Just move the code as needed.
2. Add the "alg_qos" file node in the qm debug sysfs.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Based on the Token bucket algorithm. The HAC driver supports to configure
each function's QoS in the host. The driver supports writing QoS by the
debugfs node that named "alg_qos". The qos value is 1~1000.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch updates the reset flow based on PF/VF communications. VFs
will be stopped after receiving reset message from PF, and wait for
reset finish to restart VFs.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds 'ping_all_vfs' callback that supports pf send message to
all vfs and 'ping_pf' callback that supports vf send message to pf. After
receiving the interrupt, the communication destination gets the message
by sending mailbox.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Kunpeng930 hardware supports the communication between PF and VFs.
This patch enables communication between PF and VFs by writing hardware
registers, and requests an irq for communication.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Kunpeng930 hardware supports PF/VF communications. When the device is
reset, PF can send message to VF to stop function and restart function.
This patch adjusts the reset interface to support sending message through
PF/VF communication.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use memdup_user_nul() helper instead of open-coding to
simplify the code.
v1-->v2:
fixed patch title error
v2-->v3:
return the actual error
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Kunpeng930 hardware supports address prefetching to improve performance
before doing tasks in SVA scenario.
This patch enables this function in device initialization by writing
hardware registers. In the process of reset, address prefetching is
disabled to avoid the failure of interaction between accelerator device
and SMMU.
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Compared with Kunpeng920, Kunpeng930 adds MSI configuration steps to wait
for the interrupt to be emptied. In order to be compatible with the
kunpeng920 driver, 'set_msi' callback is added in 'hisi_qm_hw_ops' to
configure hardware register. Call 'set_msi' to disable or enable MSI
during reset.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If Kunpeng 920 enabled the sva mode, the "qm alg register" process will
return directly. So the list of VF wasn't added to QM list.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add print information necessary if not use hardware crypto algs.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Kunpeng930 could be able to close master ooo when NFE occurs, which will
disable memory accessing from device and execute tasks. This ensures that
errors do not spread.
This patch enables the hardware to close master ooo when an error occurs
by writing hardware registers, and ensures that the driver will not drain
qp because the hardware will empty the tasks automatically.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In order to avoid reporting an exception but the error type is not
configured, the driver needs to configure the error type first, and then
enable the error interrupt. Before executing the task, hardware error
initialization is needed so that the hardware can detect the error in time.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Before device reset, the driver sets 'QM_RESETTING' flag, but after reset,
the wrong flag is cleared. This patch modifies the problem of inconsistent
flags.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The device needs to be initialized first, and then restart the queue to
execute tasks after PF reset.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
QM adds 'qm_mailbox_timeout' and 'qm_flr_timeout' hardware error types on
Kunpeng930. This patch enables the new error types and configures the error
types as NFE.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
'err_info' does not support dynamic configuration since it is const type.
Therefore, in order to support new error type later, 'err_info' is changed
to dynamic configuration.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Kunpeng930 could be able to stop queue by writing hardware registers,
which will trigger tasks in device to be flushed out.
In order to be compatible with the kunpeng920 driver, add 'qm_hw_ops_v3' to
adapt Kunpeng930. And 'stop_qp' callback is added in 'qm_hw_ops_v3' to
write hardware registers. Call 'stop_qp' to drain the tasks in device
before releasing queue.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Reviewed-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The "qdma" is a structure variable instead of actual data. This
structure doesn't need to be zerod, The memset is useless and redundant.
So delete it.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Kunpeng930 supports doorbell isolation to ensure that each queue
has an independent doorbell address space.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Kunpeng930 supports queue doorbell isolation.
When doorbell isolation is enabled, it supports to obtain the
maximum number of queues of one function from hardware register.
Otherwise, the 'max_qp_num' is the total number of queues.
When assigning queues to VF, it is necessary to ensure that the number
of VF queues does not exceed 'max_qp_num'.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since the code related to 'CURRENT_QM' debugfs is exactly same in
sec/hpre/zip driver, move 'CURRENT_QM' to qm.c to reduce duplicate code.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move the configuration of the total number of queues 'ctrl_qp_num'
from sec2/hpre/zip to qm.c. And get the total number of queues
from the hardware register for Kunpeng930.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
System may be able to get physical address of zero if not reserved by
firmware.
The dma address obtained by 'dma_alloc_coherent' is valid, since already
checking cpu va before, so do not check again.
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
A new generation of accelerator Kunpeng930 has appeared, and the
corresponding driver needs to be updated to support some new
algorithms of Kunpeng930. To be compatible with Kunpeng920, we
add parameter 'struct hisi_qm *qm' to sec_algs_(un)register to
identify the chip's version.
Signed-off-by: Meng Yu <yumeng18@huawei.com>
Reviewed-by: Zaibo Xu <xuzaibo@huawei.com>
Reviewed-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch fixes inconsistent of printing format with argument type.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Reviewed-by: Zaibo Xu <xuzaibo@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is no need to reset hardware when Corrected Error(CE) happens.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Reviewed-by: Zaibo Xu <xuzaibo@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is no need to share IRQ among several devices,
and set 'irqflag' as 0.
Signed-off-by: Sihang Chen <chensihang1@hisilicon.com>
Signed-off-by: Weili Qian <qianweili@huawei.com>
Reviewed-by: Zaibo Xu <xuzaibo@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since the size of base number is 16 bits, update the value of
'QM_SQC_VFT_BASE_MASK_V2' as 'GENMASK(15, 0)'.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Reviewed-by: Zaibo Xu <xuzaibo@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add 'qp_stop_fail_cb' to ensure it is called as device is resetting.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Reviewed-by: Zaibo Xu <xuzaibo@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add waiting logic for resetting as removing driver,
otherwise call trace will occur due to releasing resource.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Reviewed-by: Zaibo Xu <xuzaibo@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Enable PASID by setting 'sqc' and 'cqc' pasid bits
per queue in Kunpeng 930.
For Kunpeng 920, PASID is effective for all queues once set
in SVA scenarios.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Calling 'dma_map_single' after the data is written to
ensure that the cpu cache and dma cache are consistent.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add 'uacce_mode' parameter for ZIP, which can be set as 0(default) or 1.
'0' means ZIP is only registered to kernel crypto, and '1' means it's
registered to both kernel crypto and UACCE.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Reviewed-by: Zaibo Xu <xuzaibo@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Kunpeng920 SEC/HPRE/ZIP cannot support running user space SVA and kernel
Crypto at the same time. Therefore, the algorithms should not be registered
to Crypto as user space SVA is enabled.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Reviewed-by: Zaibo Xu <xuzaibo@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
'hisi_qm_init' initializes configuration of QM.
To improve code readability, split it into two pieces.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
