epp_policy uses the same values as cpufreq_policy.policy and resets
to CPUFREQ_POLICY_UNKNOWN during offlining. Be consistent about
it and initialize to CPUFREQ_POLICY_UNKNOWN instead of 0, too.
No functional change intended.
Signed-off-by: Christian Loehle <christian.loehle@arm.com>
Link: https://patch.msgid.link/20241211122605.3048503-3-christian.loehle@arm.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently boost_state is cached for every processor in cpudata structure
and driver boost state is set for every processor.
Both of these aren't necessary as the driver only needs to set once and
the policy stores whether boost is enabled.
Move the driver boost setting to registration and adjust all references
to cached value to pull from the policy instead.
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/20241209185248.16301-16-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
For Ryzen systems the EPP policy set by the BIOS is generally configured
to performance as this is the default register value for the CPPC request
MSR.
If a user doesn't use additional software to configure EPP then the system
will default biased towards performance and consume extra battery. Instead
configure the default to "balanced_performance" for this case.
Suggested-by: Artem S. Tashkinov <aros@gmx.com>
Reviewed-by: Dhananjay Ugwekar <dhananjay.ugwekar@amd.com>
Tested-by: Dhananjay Ugwekar <dhananjay.ugwekar@amd.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219526
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/20241209185248.16301-15-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
The ret variable is not necessary.
Reviewed-and-tested-by: Dhananjay Ugwekar <dhananjay.ugwekar@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/20241209185248.16301-14-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
For MSR systems the EPP value is in the same register as perf targets
and so divding them into two separate MSR writes is wasteful.
In msr_update_perf(), update both EPP and perf values in one write to
MSR_AMD_CPPC_REQ, and cache them if successful.
To accomplish this plumb the EPP value into the update_perf call and
modify all its callers to check the return value.
As this unifies calls, ensure that the MSR write is necessary before
flushing a write out. Also drop the comparison from the passive flow
tracing.
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/20241209185248.16301-13-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Cache the value in cpudata->epp_cached, and use that for all callers.
As all callers use cached value merge amd_pstate_get_energy_pref_index()
into show_energy_performance_preference().
Check if the EPP value is changed before writing it to MSR or
shared memory region.
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/20241209185248.16301-12-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
The limit updating code in amd_pstate_epp_update_limit() should not
only apply to EPP updates. Move it to amd_pstate_update_min_max_limit()
so other callers can benefit as well.
With this move it's not necessary to have clamp_t calls anymore because
the verify callback is called when setting limits.
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/20241209185248.16301-11-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
As msr_update_perf() calls an MSR it's possible that it fails. Pass
this return code up to the caller.
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/20241209185248.16301-10-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Storing values in the cpudata structure in different units leads
to confusion and hardcoded conversions elsewhere. After ratios are
calculated store everything in khz for any future use. Adjust all
relevant consumers for this change as well.
Suggested-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/20241209185248.16301-9-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
If writing the MSR MSR_AMD_CPPC_REQ fails then the cached value in the
amd_cpudata structure should not be updated.
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/20241209185248.16301-8-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
In "active" mode the most important thing for debugging whether
an issue is hardware or software based is to look at what was the
last thing written to the CPPC request MSR or shared memory region.
The 'amd_pstate_epp_perf' trace event shows the values being written
for all CPUs.
Reviewed-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/20241209185248.16301-4-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
amd_pstate_epp_offline() is only called from within
amd_pstate_epp_cpu_offline() and doesn't make much sense to have it at all.
Hence, remove it.
Also remove the unncessary debug print in the offline path while at it.
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241204144842.164178-6-Dhananjay.Ugwekar@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Only amd_pstate_epp driver (i.e. cppc_state = ACTIVE) enters the
amd_pstate_epp_offline() and amd_pstate_epp_cpu_online() functions,
so remove the unnecessary if condition checking if cppc_state is
equal to AMD_PSTATE_ACTIVE.
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/20241204144842.164178-5-Dhananjay.Ugwekar@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Replace similar code chunks with amd_pstate_update_perf() and
amd_pstate_set_epp() function calls.
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/20241204144842.164178-4-Dhananjay.Ugwekar@amd.com
[ML: Fix LKP reported error about unused variable]
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
amd_pstate_update_perf() should not be a part of shmem_set_epp() function,
so move it to the amd_pstate_epp_update_limit() function, where it is needed.
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/20241204144842.164178-3-Dhananjay.Ugwekar@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
MSR and shared memory based systems have different mechanisms to get and
set the epp value. Split those mechanisms into different functions and
assign them appropriately to the static calls at boot time. This eliminates
the need for the "if(cpu_feature_enabled(X86_FEATURE_CPPC))" checks at
runtime.
Also, propagate the error code from rdmsrl_on_cpu() and cppc_get_epp_perf()
to *_get_epp()'s caller, instead of returning -EIO unconditionally.
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/20241204144842.164178-2-Dhananjay.Ugwekar@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Since HYBRID_SCALING_FACTOR_MTL is not going to be suitable for Arrow
Lake in general, drop it from the "known hybrid scaling factors" list of
platforms, so the scaling factor for it will be determined with the
help of information provided by the platform firmware via CPPC.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/2307515.iZASKD2KPV@rjwysocki.net
The perf-to-frequency scaling factors are used by intel_pstate on hybrid
platforms to cast performance levels to frequency on different types of
CPUs which is needed because the generic cpufreq sysfs interface works
in the frequency domain.
For some hybrid platforms already in the field, the scaling factors are
known, but for others (including some upcoming ones) they most likely
will be different and the only way to get them that scales is to use
information provided by the platform firmware. In this particular case,
the requisite information can be obtained via CPPC.
If the P-core hybrid scaling factor for the given processor model is not
known, use CPPC to compute hybrid scaling factors for all CPUs.
Since the current default hybrid scaling factor is only suitable for a
few early hybrid platforms, add intel_hybrid_scaling_factor[] entries
for them and initialize the scaling factor to zero ("unknown") by
default.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/8476313.T7Z3S40VBb@rjwysocki.net
commit 18d9b52271 ("cpufreq/amd-pstate: Use nominal perf for limits
when boost is disabled") introduced different semantics for min/max limits
based upon whether the user turned off boost from sysfs.
This however is not necessary when the highest perf value is the boost
numerator.
Suggested-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Fixes: 18d9b52271 ("cpufreq/amd-pstate: Use nominal perf for limits when boost is disabled")
Link: https://lore.kernel.org/r/20241209185248.16301-3-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
commit ad4caad58d ("cpufreq: amd-pstate: Merge
amd_pstate_highest_perf_set() into amd_get_boost_ratio_numerator()")
changed the semantics for highest perf and commit 18d9b52271
("cpufreq/amd-pstate: Use nominal perf for limits when boost is disabled")
worked around those semantic changes.
This however is a confusing result and furthermore makes it awkward to
change frequency limits and boost due to the scaling differences. Restore
the boost numerator to highest perf again.
Suggested-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Fixes: ad4caad58d ("cpufreq: amd-pstate: Merge amd_pstate_highest_perf_set() into amd_get_boost_ratio_numerator()")
Link: https://lore.kernel.org/r/20241209185248.16301-2-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Booting with amd-pstate on 3rd Generation EPYC system incorrectly
enabled ITMT support despite the system not supporting Preferred Core
ranking. amd_pstate_init_prefcore() called during amd_pstate*_cpu_init()
requires "amd_pstate_prefcore" to be set correctly however the preferred
core support is detected only after driver registration which is too
late.
Swap the function calls around to detect preferred core support before
registring the driver via amd_pstate_register_driver(). This ensures
amd_pstate*_cpu_init() sees the correct value of "amd_pstate_prefcore"
considering the platform support.
Fixes: 279f838a61 ("x86/amd: Detect preferred cores in amd_get_boost_ratio_numerator()")
Fixes: ff2653ded4 ("cpufreq/amd-pstate: Move registration after static function call update")
Signed-off-by: K Prateek Nayak <kprateek.nayak@amd.com>
Acked-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241210032557.754-1-kprateek.nayak@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
- Rework kfence support for the HPT MMU to work on systems with >= 16TB of RAM.
- Remove the powerpc "maple" platform, used by the "Yellow Dog Powerstation".
- Add support for DYNAMIC_FTRACE_WITH_CALL_OPS,
DYNAMIC_FTRACE_WITH_DIRECT_CALLS & BPF Trampolines.
- Add support for running KVM nested guests on Power11.
- Other small features, cleanups and fixes.
Thanks to: Amit Machhiwal, Arnd Bergmann, Christophe Leroy, Costa Shulyupin,
David Hunter, David Wang, Disha Goel, Gautam Menghani, Geert Uytterhoeven,
Hari Bathini, Julia Lawall, Kajol Jain, Keith Packard, Lukas Bulwahn, Madhavan
Srinivasan, Markus Elfring, Michal Suchanek, Ming Lei, Mukesh Kumar Chaurasiya,
Nathan Chancellor, Naveen N Rao, Nicholas Piggin, Nysal Jan K.A, Paulo Miguel
Almeida, Pavithra Prakash, Ritesh Harjani (IBM), Rob Herring (Arm), Sachin P
Bappalige, Shen Lichuan, Simon Horman, Sourabh Jain, Thomas Weißschuh, Thorsten
Blum, Thorsten Leemhuis, Venkat Rao Bagalkote, Zhang Zekun,
zhang jiao.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRjvi15rv0TSTaE+SIF0oADX8seIQUCZ0Fi5AAKCRAF0oADX8se
IeI0AQCAkNWRYzGNzPM6aMwDpq5qdeZzvp0rZxuNsRSnIKJlxAD+PAOxOietgjbQ
Lxt3oizg+UcH/304Y/iyT8IrwI4n+gE=
=xNtu
-----END PGP SIGNATURE-----
Merge tag 'powerpc-6.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Rework kfence support for the HPT MMU to work on systems with >= 16TB
of RAM.
- Remove the powerpc "maple" platform, used by the "Yellow Dog
Powerstation".
- Add support for DYNAMIC_FTRACE_WITH_CALL_OPS,
DYNAMIC_FTRACE_WITH_DIRECT_CALLS & BPF Trampolines.
- Add support for running KVM nested guests on Power11.
- Other small features, cleanups and fixes.
Thanks to Amit Machhiwal, Arnd Bergmann, Christophe Leroy, Costa
Shulyupin, David Hunter, David Wang, Disha Goel, Gautam Menghani, Geert
Uytterhoeven, Hari Bathini, Julia Lawall, Kajol Jain, Keith Packard,
Lukas Bulwahn, Madhavan Srinivasan, Markus Elfring, Michal Suchanek,
Ming Lei, Mukesh Kumar Chaurasiya, Nathan Chancellor, Naveen N Rao,
Nicholas Piggin, Nysal Jan K.A, Paulo Miguel Almeida, Pavithra Prakash,
Ritesh Harjani (IBM), Rob Herring (Arm), Sachin P Bappalige, Shen
Lichuan, Simon Horman, Sourabh Jain, Thomas Weißschuh, Thorsten Blum,
Thorsten Leemhuis, Venkat Rao Bagalkote, Zhang Zekun, and zhang jiao.
* tag 'powerpc-6.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (89 commits)
EDAC/powerpc: Remove PPC_MAPLE drivers
powerpc/perf: Add per-task/process monitoring to vpa_pmu driver
powerpc/kvm: Add vpa latency counters to kvm_vcpu_arch
docs: ABI: sysfs-bus-event_source-devices-vpa-pmu: Document sysfs event format entries for vpa_pmu
powerpc/perf: Add perf interface to expose vpa counters
MAINTAINERS: powerpc: Mark Maddy as "M"
powerpc/Makefile: Allow overriding CPP
powerpc-km82xx.c: replace of_node_put() with __free
ps3: Correct some typos in comments
powerpc/kexec: Fix return of uninitialized variable
macintosh: Use common error handling code in via_pmu_led_init()
powerpc/powermac: Use of_property_match_string() in pmac_has_backlight_type()
powerpc: remove dead config options for MPC85xx platform support
powerpc/xive: Use cpumask_intersects()
selftests/powerpc: Remove the path after initialization.
powerpc/xmon: symbol lookup length fixed
powerpc/ep8248e: Use %pa to format resource_size_t
powerpc/ps3: Reorganize kerneldoc parameter names
KVM: PPC: Book3S HV: Fix kmv -> kvm typo
powerpc/sstep: make emulate_vsx_load and emulate_vsx_store static
...
- Add virtual cpufreq driver for guest kernels (David Dai).
- Minor cleanup to various cpufreq drivers (Andy Shevchenko, Dhruva
Gole, Jie Zhan, Jinjie Ruan, Shuosheng Huang, Sibi Sankar, and Yuan
Can).
- Revert "cpufreq: brcmstb-avs-cpufreq: Fix initial command check" (Colin
Ian King).
- Improve DT bindings for qcom-hw driver (Dmitry Baryshkov, Konrad
Dybcio, and Nikunj Kela).
- Make cpuidle_play_dead() try all idle states with :enter_dead()
callbacks and change their return type to void (Rafael Wysocki).
-----BEGIN PGP SIGNATURE-----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=aB0d
-----END PGP SIGNATURE-----
Merge tag 'pm-6.13-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These mostly are updates of cpufreq drivers used on ARM platforms plus
one new DT-based cpufreq driver for virtualized guests and two cpuidle
changes that should not make any difference on systems currently in
the field, but will be needed for future development:
- Add virtual cpufreq driver for guest kernels (David Dai)
- Minor cleanup to various cpufreq drivers (Andy Shevchenko, Dhruva
Gole, Jie Zhan, Jinjie Ruan, Shuosheng Huang, Sibi Sankar, and Yuan
Can)
- Revert "cpufreq: brcmstb-avs-cpufreq: Fix initial command check"
(Colin Ian King)
- Improve DT bindings for qcom-hw driver (Dmitry Baryshkov, Konrad
Dybcio, and Nikunj Kela)
- Make cpuidle_play_dead() try all idle states with :enter_dead()
callbacks and change their return type to void (Rafael Wysocki)"
* tag 'pm-6.13-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (22 commits)
cpuidle: Change :enter_dead() driver callback return type to void
cpuidle: Do not return from cpuidle_play_dead() on callback failures
arm64: dts: qcom: sc8180x: Add a SoC-specific compatible to cpufreq-hw
dt-bindings: cpufreq: cpufreq-qcom-hw: Add SC8180X compatible
cpufreq: sun50i: add a100 cpufreq support
cpufreq: mediatek-hw: Fix wrong return value in mtk_cpufreq_get_cpu_power()
cpufreq: CPPC: Fix wrong return value in cppc_get_cpu_power()
cpufreq: CPPC: Fix wrong return value in cppc_get_cpu_cost()
cpufreq: loongson3: Check for error code from devm_mutex_init() call
cpufreq: scmi: Fix cleanup path when boost enablement fails
cpufreq: CPPC: Fix possible null-ptr-deref for cppc_get_cpu_cost()
cpufreq: CPPC: Fix possible null-ptr-deref for cpufreq_cpu_get_raw()
Revert "cpufreq: brcmstb-avs-cpufreq: Fix initial command check"
dt-bindings: cpufreq: cpufreq-qcom-hw: Add SAR2130P compatible
cpufreq: add virtual-cpufreq driver
dt-bindings: cpufreq: add virtual cpufreq device
cpufreq: loongson2: Unregister platform_driver on failure
cpufreq: ti-cpufreq: Remove revision offsets in AM62 family
cpufreq: ti-cpufreq: Allow backward compatibility for efuse syscon
cppc_cpufreq: Remove HiSilicon CPPC workaround
...
- Set the required dev for a required OPP during genpd attach
- Add support for required OPPs to dev_pm_domain_attach_list()
pmdomain providers:
- ti: Enable GENPD_FLAG_ACTIVE_WAKEUP flag for ti_sci PM domains
- mediatek: Add support for MT6735 PM domains
- mediatek: Use OF-specific regulator API to get power domain supply
- qcom: Add support for the SM8750/SAR2130P/qcs615/qcs8300 rpmhpds
pmdomain consumers:
- Convert a couple of consumer drivers to *_pm_domain_attach|detach_list()
opp core:
- Rework and cleanup some code that manages required OPPs
- Remove *_opp_attach|detach_genpd()
-----BEGIN PGP SIGNATURE-----
iQJLBAABCgA1FiEEugLDXPmKSktSkQsV/iaEJXNYjCkFAmc7Y+QXHHVsZi5oYW5z
c29uQGxpbmFyby5vcmcACgkQ/iaEJXNYjCmbrw/9FVdo3+mo6EZne+Zsxc0+3N9G
bRwkgyCB8WSFy6MHD1TRyP9u8bFgFDitSxcUGuBW0l9t1le3IcsYwfbTEEZpUkU4
iasPoZoFKA3Akfr7tvQpIpSNh8MIBMFy7CfxWpsfiHlmwrIH6oT6HmlwWwFsbVxh
Fv8xA5SOE1KRHq0Aos23h7MizPsav/PYSh/4Ga5l6ZBlm40c16cE0i0M4RRUnoNY
FmUBe57HoumDd05ToFR9wrqMEVWbAJHV4xZpZwnfYUhwGrgbxUWI/1FIfwxtob12
OExPr9kiV8/f8Kfp3E3ul0R8q8XYaYZaT3R7nF5QOngLZCCpD5H9aWEcAihUryBh
Ol9Wao0Ku1JqLc776bjwf92ozFDtx0yUN/8LXmQgUu+e+MC3eAOrsls+U4731p+Y
V80mvBpqn8AbX7LOjJvmbOhK6Qnm0cHo2cs0afBSS5c9RBcCWuEy9d7n8dks6JX2
7H6ySDaKoEEK06V6VzEKdHQoRFkmw95w4n7Ei3OL0cxNLcT1ILGA1+O7PPw+6h4T
3UnSik6szZCBXFFaDsw4J53HZACVZWbkyrk5Dbsigte8lh6e2VI+qd9whd46nuCY
Sn4vJ399FJvXBuEIu+8yymGwn/NSpgd6ybpkwdDNJ+fItbes7DQhtxM6k74ANAhf
0irf1o4Yv0S5W+pXBAM=
=SpyF
-----END PGP SIGNATURE-----
Merge tag 'pmdomain-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull pmdomain updates from Ulf Hansson:
"pmdomain core:
- Set the required dev for a required OPP during genpd attach
- Add support for required OPPs to dev_pm_domain_attach_list()
pmdomain providers:
- ti: Enable GENPD_FLAG_ACTIVE_WAKEUP flag for ti_sci PM domains
- mediatek: Add support for MT6735 PM domains
- mediatek: Use OF-specific regulator API to get power domain supply
- qcom: Add support for the SM8750/SAR2130P/qcs615/qcs8300 rpmhpds
pmdomain consumers:
- Convert a couple of consumer drivers to
*_pm_domain_attach|detach_list()
opp core:
- Rework and cleanup some code that manages required OPPs
- Remove *_opp_attach|detach_genpd()"
* tag 'pmdomain-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm: (25 commits)
pmdomain: qcom: rpmhpd: Add rpmhpd support for SM8750
dt-bindings: power: qcom,rpmpd: document the SM8750 RPMh Power Domains
pmdomain: imx: Use of_property_present() for non-boolean properties
pmdomain: imx: gpcv2: replace dev_err() with dev_err_probe()
pmdomain: ti-sci: Use scope based of_node_put() to simplify code.
pmdomain: ti-sci: Add missing of_node_put() for args.np
pmdomain: ti-sci: set the GENPD_FLAG_ACTIVE_WAKEUP flag for all PM domains
pmdomain: mediatek: Add support for MT6735
pmdomain: qcom: rpmhpd: add support for SAR2130P
dt-bindings: power: Add binding for MediaTek MT6735 power controller
dt-bindings: power: rpmpd: Add SAR2130P compatible
OPP: Drop redundant *_opp_attach|detach_genpd()
cpufreq: qcom-nvmem: Convert to dev_pm_domain_attach|detach_list()
media: venus: Convert into devm_pm_domain_attach_list() for OPP PM domain
drm/tegra: gr3d: Convert into devm_pm_domain_attach_list()
OPP: Drop redundant code in _link_required_opps()
pmdomain: core: Set the required dev for a required OPP during genpd attach
pmdomain: core: Manage the default required OPP from a separate function
PM: domains: Support required OPPs in dev_pm_domain_attach_list()
OPP: Rework _set_required_devs() to manage a single device per call
...
with the purpose of using such hints when making scheduling decisions
- Determine the boost enumerator for each AMD core based on its type: efficiency
or performance, in the cppc driver
- Add the type of a CPU to the topology CPU descriptor with the goal of
supporting and making decisions based on the type of the respective core
- Add a feature flag to denote AMD cores which have heterogeneous topology and
enable SD_ASYM_PACKING for those
- Check microcode revisions before disabling PCID on Intel
- Cleanups and fixlets
-----BEGIN PGP SIGNATURE-----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=420r
-----END PGP SIGNATURE-----
Merge tag 'x86_cpu_for_v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cpuid updates from Borislav Petkov:
- Add a feature flag which denotes AMD CPUs supporting workload
classification with the purpose of using such hints when making
scheduling decisions
- Determine the boost enumerator for each AMD core based on its type:
efficiency or performance, in the cppc driver
- Add the type of a CPU to the topology CPU descriptor with the goal of
supporting and making decisions based on the type of the respective
core
- Add a feature flag to denote AMD cores which have heterogeneous
topology and enable SD_ASYM_PACKING for those
- Check microcode revisions before disabling PCID on Intel
- Cleanups and fixlets
* tag 'x86_cpu_for_v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Remove redundant CONFIG_NUMA guard around numa_add_cpu()
x86/cpu: Fix FAM5_QUARK_X1000 to use X86_MATCH_VFM()
x86/cpu: Fix formatting of cpuid_bits[] in scattered.c
x86/cpufeatures: Add X86_FEATURE_AMD_WORKLOAD_CLASS feature bit
x86/amd: Use heterogeneous core topology for identifying boost numerator
x86/cpu: Add CPU type to struct cpuinfo_topology
x86/cpu: Enable SD_ASYM_PACKING for PKG domain on AMD
x86/cpufeatures: Add X86_FEATURE_AMD_HETEROGENEOUS_CORES
x86/cpufeatures: Rename X86_FEATURE_FAST_CPPC to have AMD prefix
x86/mm: Don't disable PCID when INVLPG has been fixed by microcode
Update EPP default for balance_performance to 32.
This will give better performance out of the box using Intel P-State
powersave governor while still offering power savings compared to
performance governor.
This is in line with what has already been done for Emerald Rapids and
Sapphire Rapids.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20241112235946.368082-1-srinivas.pandruvada@linux.intel.com
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This driver is no longer buildable since the PPC_MAPLE platform was
removed, see commit 62f8f307c8 ("powerpc/64: Remove maple platform").
Remove the driver.
Note that the comment in the driver says it supports "SMU & 970FX
based G5 Macs", but that's not true, that comment was copied from
pmac64-cpufreq.c, which still exists and continues to support those
machines.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://patch.msgid.link/20241112085148.415574-1-mpe@ellerman.id.au
Replace the 32-bit MSR access function with a 64-bit variant to simplify
the call site, eliminating unnecessary 32-bit value manipulations.
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Link: https://patch.msgid.link/20241106182313.165297-1-chang.seok.bae@intel.com
[ rjw: Subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Notice that hybrid_init_cpu_capacity_scaling() only needs to hold
hybrid_capacity_lock around __hybrid_init_cpu_capacity_scaling()
calls, so introduce a "locked" wrapper around the latter and call
it from the former. This allows to drop a local variable and a
label that are not needed any more.
Also, rename __hybrid_init_cpu_capacity_scaling() to
__hybrid_refresh_cpu_capacity_scaling() for consistency.
Interestingly enough, this fixes a locking issue introduced by commit
929ebc93cc ("cpufreq: intel_pstate: Set asymmetric CPU capacity on
hybrid systems") that put an arch_enable_hybrid_capacity_scale() call
under hybrid_capacity_lock, which was a mistake because the latter is
acquired in CPU hotplug paths and so it cannot be held around
cpus_read_lock() calls.
Link: https://lore.kernel.org/linux-pm/SJ1PR11MB6129EDBF22F8A90FC3A3EDC8B9582@SJ1PR11MB6129.namprd11.prod.outlook.com/
Fixes: 929ebc93cc ("cpufreq: intel_pstate: Set asymmetric CPU capacity on hybrid systems")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reported-by: "Borah, Chaitanya Kumar" <chaitanya.kumar.borah@intel.com>
Link: https://patch.msgid.link/12554508.O9o76ZdvQC@rjwysocki.net
[ rjw: Changelog update ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Let's add cpufreq nvmem based for allwinner a100 soc. It's similar to h6,
let us use efuse_xlate to extract the differentiated part.
Signed-off-by: Shuosheng Huang <huangshuosheng@allwinnertech.com>
[masterr3c0rd@epochal.quest: add A100 to opp_match_list]
Signed-off-by: Cody Eksal <masterr3c0rd@epochal.quest>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Parthiban Nallathambi <parthiban@linumiz.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
mtk_cpufreq_get_cpu_power() return 0 if the policy is NULL. Then in
em_create_perf_table(), the later zero check for power is not invalid
as power is uninitialized. As Lukasz suggested, it must return -EINVAL when
the 'policy' is not found. So return -EINVAL to fix it.
Cc: stable@vger.kernel.org
Fixes: 4855e26bcf ("cpufreq: mediatek-hw: Add support for CPUFREQ HW")
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Suggested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
cppc_get_cpu_power() return 0 if the policy is NULL. Then in
em_create_perf_table(), the later zero check for power is not valid
as power is uninitialized. As Quentin pointed out, kernel energy model
core check the return value of active_power() first, so if the callback
failed it should tell the core. So return -EINVAL to fix it.
Fixes: a78e720756 ("cpufreq: CPPC: Fix possible null-ptr-deref for cpufreq_cpu_get_raw()")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Suggested-by: Quentin Perret <qperret@google.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
cppc_get_cpu_cost() return 0 if the policy is NULL. Then in
em_compute_costs(), the later zero check for cost is not valid
as cost is uninitialized. As Quentin pointed out, kernel energy model
core check the return value of get_cost() first, so if the callback
failed it should tell the core. Return -EINVAL to fix it.
Fixes: 1a1374bb8c ("cpufreq: CPPC: Fix possible null-ptr-deref for cppc_get_cpu_cost()")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/c4765377-7830-44c2-84fa-706b6e304e10@stanley.mountain/
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Suggested-by: Quentin Perret <qperret@google.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Even if it's not critical, the avoidance of checking the error code
from devm_mutex_init() call today diminishes the point of using devm
variant of it. Tomorrow it may even leak something. Add the missed
check.
Fixes: ccf5145414 ("cpufreq: Add Loongson-3 CPUFreq driver support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Commit 929ebc93cc ("cpufreq: intel_pstate: Set asymmetric CPU
capacity on hybrid systems") overlooked a corner case in which some
CPUs may be offline to start with and brought back online later,
after the intel_pstate driver has been registered, so their asymmetric
capacity will not be set.
Address this by calling hybrid_update_capacity() in the CPU
initialization path that is executed instead of the online path
for those CPUs.
Note that this asymmetric capacity update will be skipped during
driver initialization and mode switches because hybrid_max_perf_cpu
is NULL in those cases.
Fixes: 929ebc93cc ("cpufreq: intel_pstate: Set asymmetric CPU capacity on hybrid systems")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/1913414.tdWV9SEqCh@rjwysocki.net
Modify intel_pstate_register_driver() to clear hybrid_max_perf_cpu
before calling cpufreq_register_driver(), so that asymmetric CPU
capacity scaling is not updated until hybrid_init_cpu_capacity_scaling()
runs down the road. This is done in preparation for a subsequent
change adding asymmetric CPU capacity computation to the CPU init path
to handle CPUs that are initially offline.
The information on whether or not hybrid_max_perf_cpu was NULL before
it has been cleared is passed to hybrid_init_cpu_capacity_scaling(),
so full initialization of CPU capacity scaling can be skipped if it
has been carried out already.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/4616631.LvFx2qVVIh@rjwysocki.net
cpufreq_cpu_get_raw() may return NULL if the cpu is not in
policy->cpus cpu mask and it will cause null pointer dereference,
so check NULL for cppc_get_cpu_cost().
Fixes: 740fcdc2c2 ("cpufreq: CPPC: Register EM based on efficiency class information")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
cpufreq_cpu_get_raw() may return NULL if the cpu is not in
policy->cpus cpu mask and it will cause null pointer dereference.
Fixes: 740fcdc2c2 ("cpufreq: CPPC: Register EM based on efficiency class information")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Currently the condition ((rc != -ENOTSUPP) || (rc != -EINVAL)) is always
true because rc cannot be equal to two different values at the same time,
so it must be not equal to at least one of them. Fix the original commit
that introduced the issue.
This reverts commit 22a26cc6a5.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
On shared memory designs the static functions need to work before
registration is done or the system can hang at bootup.
Move the registration later in amd_pstate_init() to solve this.
Fixes: b427ac4084 ("cpufreq/amd-pstate: Remove the redundant amd_pstate_set_driver() call")
Reported-by: Klara Modin <klarasmodin@gmail.com>
Closes: https://lore.kernel.org/linux-pm/cf9c146d-bacf-444e-92e2-15ebf513af96@gmail.com/#t
Tested-by: Klara Modin <klarasmodin@gmail.com>
Tested-by: Dhananjay Ugwekar <dhananjay.ugwekar@amd.com>
Link: https://lore.kernel.org/r/20241028145542.1739160-2-superm1@kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
As the driver can be changed in and out of different modes it's possible
that adjust_perf is assigned when it shouldn't be.
This could happen if an MSR design is started up in passive mode and then
switches to active mode.
To solve this explicitly clear `adjust_perf` in amd_pstate_epp_cpu_init().
Tested-by: Klara Modin <klarasmodin@gmail.com>
Tested-by: Dhananjay Ugwekar <dhananjay.ugwekar@amd.com>
Link: https://lore.kernel.org/r/20241028145542.1739160-1-superm1@kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Introduce a virtualized cpufreq driver for guest kernels to improve
performance and power of workloads within VMs.
This driver does two main things:
1. Sends the frequency of vCPUs as a hint to the host. The host uses the
hint to schedule the vCPU threads and decide physical CPU frequency.
2. If a VM does not support a virtualized FIE(like AMUs), it queries the
host CPU frequency by reading a MMIO region of a virtual cpufreq device
to update the guest's frequency scaling factor periodically. This enables
accurate Per-Entity Load Tracking for tasks running in the guest.
Co-developed-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: David Dai <davidai@google.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Set min_perf to lowest_perf for shared memory systems, similar to the MSR
based systems.
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/20241023102108.5980-5-Dhananjay.Ugwekar@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
The EPP value being set in perf_ctrls.energy_perf is not being propagated
to the shared memory, fix that.
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/20241023102108.5980-4-Dhananjay.Ugwekar@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
MSR_AMD_CPPC_ENABLE is a write once register, i.e. attempting to clear
it is futile, it will not take effect. Hence, return if disable (0)
argument is passed to the msr_cppc_enable()
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/20241023102108.5980-3-Dhananjay.Ugwekar@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
commit 642aff3964b0f ("cpufreq/amd-pstate: Set the initial min_freq to
lowest_nonlinear_freq") changed the initial minimum frequency to lowest
nonlinear frequency, but the unit tests weren't updated and now fail.
Update them to match this same change.
Fixes: 642aff3964b0f ("cpufreq/amd-pstate: Set the initial min_freq to lowest_nonlinear_freq")
Link: https://lore.kernel.org/r/20241017173439.4924-1-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Currently the default cpufreq driver for all the AMD EPYC servers is
acpi-cpufreq. Going forward, switch to amd-pstate as the default
driver on the AMD EPYC server platforms with CPU family 0x1A or
higher. The default mode will be active mode.
Testing shows that amd-pstate with active mode and performance
governor provides comparable or better performance per-watt against
acpi-cpufreq + performance governor.
Likewise, amd-pstate with active mode and powersave governor with the
energy_performance_preference=power (EPP=255) provides comparable or
better performance per-watt against acpi-cpufreq + schedutil governor
for a wide range of workloads.
Users can still revert to using acpi-cpufreq driver on these platforms
with the "amd_pstate=disable" kernel commandline parameter.
Signed-off-by: Swapnil Sapkal <swapnil.sapkal@amd.com>
Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241021101836.9047-3-gautham.shenoy@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
The amd-pstate driver sets CPPC_REQ.min_perf to CPPC_REQ.max_perf when
in active mode with performance governor. Typically CPPC_REQ.max_perf
is set to CPPC.highest_perf. This causes frequency throttling on
power-limited platforms which causes performance regressions on
certain classes of workloads.
Hence, set the CPPC_REQ.min_perf to the CPPC.nominal_perf or
CPPC_REQ.max_perf, whichever is lower of the two.
Fixes: ffa5096a7c ("cpufreq: amd-pstate: implement Pstate EPP support for the AMD processors")
Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241021101836.9047-2-gautham.shenoy@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
amd_pstate_set_driver() is called twice, once in amd_pstate_init() and once
as part of amd_pstate_register_driver(). Move around code and eliminate
the redundancy.
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241017100528.300143-5-Dhananjay.Ugwekar@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Replace the switch case with a more readable if condition.
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241017100528.300143-4-Dhananjay.Ugwekar@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Replace a similar chunk of code in amd_pstate_register_driver() with
amd_pstate_set_driver() call.
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241017100528.300143-3-Dhananjay.Ugwekar@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Replace a similar chunk of code in amd_pstate_init() with
amd_pstate_register() call.
Suggested-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241017100528.300143-2-Dhananjay.Ugwekar@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
According to the AMD architectural programmer's manual volume 2 [1], in
section "17.6.4.1 CPPC_CAPABILITY_1" lowest_nonlinear_perf is described
as "Reports the most energy efficient performance level (in terms of
performance per watt). Above this threshold, lower performance levels
generally result in increased energy efficiency. Reducing performance
below this threshold does not result in total energy savings for a given
computation, although it reduces instantaneous power consumption". So
lowest_nonlinear_perf is the most power efficient performance level, and
going below that would lead to a worse performance/watt.
Also, setting the minimum frequency to lowest_nonlinear_freq (instead of
lowest_freq) allows the CPU to idle at a higher frequency which leads
to more time being spent in a deeper idle state (as trivial idle tasks
are completed sooner). This has shown a power benefit in some systems,
in other systems, power consumption has increased but so has the
throughput/watt.
Modify the initial policy_data->min set by cpufreq-core to
lowest_nonlinear_freq, in the ->verify() callback. Also set the
cpudata->req[0] to FREQ_QOS_MIN_DEFAULT_VALUE (i.e. 0), so that it also
gets overriden by the check in verify function.
Link: https://www.amd.com/content/dam/amd/en/documents/processor-tech-docs/programmer-references/24593.pdf [1]
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241017053927.25285-3-Dhananjay.Ugwekar@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Merge the two verify() callback functions and rename the
cpufreq_policy_data argument for better readability.
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/20241017053927.25285-2-Dhananjay.Ugwekar@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
The EPP value doesn't need to be cached to the CPPC request in
amd_pstate_epp_update_limit() because it's passed as an argument
at the end to amd_pstate_set_epp() and stored at that time.
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Reviewed-by: Perry Yuan <perry.yuan@amd.com>
Tested-by: Dhananjay Ugwekar <dhananjay.ugwekar@amd.com>
Link: https://lore.kernel.org/r/20241012174519.897-4-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
When the EPP updates are set the maximum capable frequency for the
CPU is used to set the upper limit instead of that of the policy.
Adjust amd_pstate_epp_update_limit() to reuse policy calculation code
from amd_pstate_update_min_max_limit().
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Reviewed-by: Perry Yuan <perry.yuan@amd.com>
Tested-by: Dhananjay Ugwekar <dhananjay.ugwekar@amd.com>
Link: https://lore.kernel.org/r/20241012174519.897-3-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
When boost is changed the CPPC value is changed in amd_pstate_cpu_boost_update()
but then changed again when refresh_frequency_limits() and all it's callbacks
occur. The first is a pointless write, so instead just update the limits for
the policy and let the policy refresh anchor everything properly.
Fixes: c8c68c38b5 ("cpufreq: amd-pstate: initialize core precision boost state")
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Reviewed-by: Perry Yuan <perry.yuan@amd.com>
Tested-by: Dhananjay Ugwekar <dhananjay.ugwekar@amd.com>
Link: https://lore.kernel.org/r/20241012174519.897-2-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Existing function names "cppc_*" and "pstate_*" for shared memory and
MSR based systems are not intuitive enough, replace them with "shmem_*" and
"msr_*" respectively.
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20240917091434.10685-1-Dhananjay.Ugwekar@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/cpufreq to use .remove(),
with the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://patch.msgid.link/20241020153910.324096-2-u.kleine-koenig@baylibre.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When I booted my RK3588 based system I noticed that cpufreq complained
about system clock:
[ +0.007211] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 816000 KHz, changing to: 1008000 KHz
Then I realized that unit is displayed wrong: "KHz" instead of "kHz".
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://patch.msgid.link/20240909095529.2325103-1-marcin.juszkiewicz@linaro.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When cpufreq_register_driver() returns error, the cpufreq_init() returns
without unregister platform_driver, fix by add missing
platform_driver_unregister() when cpufreq_register_driver() failed.
Fixes: f8ede0f700 ("MIPS: Loongson 2F: Add CPU frequency scaling support")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
When boost has been disabled the limit for perf should be nominal perf not
the highest perf. Using the latter to do calculations will lead to
incorrect values that are still above nominal.
Fixes: ad4caad58d ("cpufreq: amd-pstate: Merge amd_pstate_highest_perf_set() into amd_get_boost_ratio_numerator()")
Reported-by: Peter Jung <ptr1337@cachyos.org>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219348
Reviewed-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Tested-by: Dhananjay Ugwekar <dhananjay.ugwekar@amd.com>
Link: https://lore.kernel.org/r/20241012174519.897-1-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Rather than hooking up the PM domains through _opp_attach_genpd() and
manually manage runtime PM for the corresponding virtual devices created by
genpd during attach, let's avoid the boilerplate-code by converting into
dev_pm_domain_attach|detach_list.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20241002122232.194245-11-ulf.hansson@linaro.org
With the Silicon revision being taken directly from socinfo, there's no
longer any need for reading any SOC register for revision from this driver.
Hence, we do not require any rev_offset for AM62 family of devices.
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The AM625 syscon for efuse was being taken earlier from the wkup_conf node
where the entire wkup_conf was marked as "syscon". This is wrong and will
be fixed in the devicetree. However, whenever that does happen will end up
breaking this driver for that device because of the change in efuse offset.
Hence, to avoid breaking any sort of backward compatibility of devicetrees
use a quirk to distinguish and accordingly use 0x0 offset for the new
syscon node.
Suggested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
While switching the driver mode between active and passive, Collaborative
Processor Performance Control (CPPC) is disabled in
amd_pstate_unregister_driver(). But, it is not enabled back while registering
the new driver (passive or active). This leads to the new driver mode not
working correctly, so enable it back in amd_pstate_register_driver().
Fixes: 3ca7bc818d ("cpufreq: amd-pstate: Add guided mode control support via sysfs")
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241004122303.94283-1-Dhananjay.Ugwekar@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
- Fix CPU device node reference counting in the cpufreq core (Miquel
Sabaté Solà).
- Turn the spinlock used by the intel_pstate driver in hard IRQ
context into a raw one to prevent the driver from crashing when
PREEMPT_RT is enabled (Uwe Kleine-König).
-----BEGIN PGP SIGNATURE-----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=mgVf
-----END PGP SIGNATURE-----
Merge tag 'pm-6.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix two cpufreq issues, one in the core and one in the
intel_pstate driver:
- Fix CPU device node reference counting in the cpufreq core (Miquel
Sabaté Solà)
- Turn the spinlock used by the intel_pstate driver in hard IRQ
context into a raw one to prevent the driver from crashing when
PREEMPT_RT is enabled (Uwe Kleine-König)"
* tag 'pm-6.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: Avoid a bad reference count on CPU node
cpufreq: intel_pstate: Make hwp_notify_lock a raw spinlock
Since commit 6c8d750f97 ("cpufreq / cppc: Work around for Hisilicon CPPC
cpufreq"), we introduce a workround for HiSilicon platforms that do not
support performance feedback counters, whereas they can get the actual
frequency from the desired perf register. Later on, FIE is disabled in
that workaround as well.
Now the workround can be handled by the common code. Desired perf would be
read and converted to frequency if feedback counters don't change. FIE
would be disabled if the CPPC regs are in PCC region.
Hence, the workaround is no longer needed and can be safely removed, in an
effort to consolidate the driver procedure.
Signed-off-by: Jie Zhan <zhanjie9@hisilicon.com>
Reviewed-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Reviewed-by: Huisong Li <lihuisong@huawei.com>
[ Viresh: Move fie_disabled withing CONFIG option to fix warning ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The CPPC performance feedback counters could be 0 or unchanged when the
target cpu is in a low-power idle state, e.g. power-gated or clock-gated.
When the counters are 0, cppc_cpufreq_get_rate() returns 0 KHz, which makes
cpufreq_online() get a false error and fail to generate a cpufreq policy.
When the counters are unchanged, the existing cppc_perf_from_fbctrs()
returns a cached desired perf, but some platforms may update the real
frequency back to the desired perf reg.
For the above cases in cppc_cpufreq_get_rate(), get the latest desired perf
from the CPPC reg to reflect the frequency because some platforms may
update the actual frequency back there; if failed, use the cached desired
perf.
Fixes: 6a4fec4f6d ("cpufreq: cppc: cppc_cpufreq_get_rate() returns zero in all error cases.")
Signed-off-by: Jie Zhan <zhanjie9@hisilicon.com>
Reviewed-by: Zeng Heng <zengheng4@huawei.com>
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Reviewed-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
notify_hwp_interrupt() is called via sysvec_thermal() ->
smp_thermal_vector() -> intel_thermal_interrupt() in hard irq context.
For this reason it must not use a simple spin_lock that sleeps with
PREEMPT_RT enabled. So convert it to a raw spinlock.
Reported-by: xiao sheng wen <atzlinux@sina.com>
Link: https://bugs.debian.org/1076483
Signed-off-by: Uwe Kleine-König <ukleinek@debian.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: xiao sheng wen <atzlinux@sina.com>
Link: https://patch.msgid.link/20240919081121.10784-2-ukleinek@debian.org
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Implement the SCHED_DEADLINE server infrastructure - Daniel Bristot de Oliveira's
last major contribution to the kernel:
"SCHED_DEADLINE servers can help fixing starvation issues of low priority
tasks (e.g., SCHED_OTHER) when higher priority tasks monopolize CPU
cycles. Today we have RT Throttling; DEADLINE servers should be able to
replace and improve that."
(Daniel Bristot de Oliveira, Peter Zijlstra, Joel Fernandes,
Youssef Esmat, Huang Shijie)
- Preparatory changes for sched_ext integration:
- Use set_next_task(.first) where required
- Fix up set_next_task() implementations
- Clean up DL server vs. core sched
- Split up put_prev_task_balance()
- Rework pick_next_task()
- Combine the last put_prev_task() and the first set_next_task()
- Rework dl_server
- Add put_prev_task(.next)
(Peter Zijlstra, with a fix by Tejun Heo)
- Complete the EEVDF transition and refine EEVDF scheduling:
- Implement delayed dequeue
- Allow shorter slices to wakeup-preempt
- Use sched_attr::sched_runtime to set request/slice suggestion
- Document the new feature flags
- Remove unused and duplicate-functionality fields
- Simplify & unify pick_next_task_fair()
- Misc debuggability enhancements
(Peter Zijlstra, with fixes/cleanups by Dietmar Eggemann,
Valentin Schneider and Chuyi Zhou)
- Initialize the vruntime of a new task when it is first enqueued,
resulting in significant decrease in latency of newly woken tasks.
(Zhang Qiao)
- Introduce SM_IDLE and an idle re-entry fast-path in __schedule()
(K Prateek Nayak, Peter Zijlstra)
- Clean up and clarify the usage of Clean up usage of rt_task()
(Qais Yousef)
- Preempt SCHED_IDLE entities in strict cgroup hierarchies
(Tianchen Ding)
- Clarify the documentation of time units for deadline scheduler
parameters. (Christian Loehle)
- Remove the HZ_BW chicken-bit feature flag introduced a year ago,
the original change seems to be working fine.
(Phil Auld)
- Misc fixes and cleanups (Chen Yu, Dan Carpenter, Huang Shijie,
Peilin He, Qais Yousefm and Vincent Guittot)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=TEC6
-----END PGP SIGNATURE-----
Merge tag 'sched-core-2024-09-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
- Implement the SCHED_DEADLINE server infrastructure - Daniel Bristot
de Oliveira's last major contribution to the kernel:
"SCHED_DEADLINE servers can help fixing starvation issues of low
priority tasks (e.g., SCHED_OTHER) when higher priority tasks
monopolize CPU cycles. Today we have RT Throttling; DEADLINE
servers should be able to replace and improve that."
(Daniel Bristot de Oliveira, Peter Zijlstra, Joel Fernandes, Youssef
Esmat, Huang Shijie)
- Preparatory changes for sched_ext integration:
- Use set_next_task(.first) where required
- Fix up set_next_task() implementations
- Clean up DL server vs. core sched
- Split up put_prev_task_balance()
- Rework pick_next_task()
- Combine the last put_prev_task() and the first set_next_task()
- Rework dl_server
- Add put_prev_task(.next)
(Peter Zijlstra, with a fix by Tejun Heo)
- Complete the EEVDF transition and refine EEVDF scheduling:
- Implement delayed dequeue
- Allow shorter slices to wakeup-preempt
- Use sched_attr::sched_runtime to set request/slice suggestion
- Document the new feature flags
- Remove unused and duplicate-functionality fields
- Simplify & unify pick_next_task_fair()
- Misc debuggability enhancements
(Peter Zijlstra, with fixes/cleanups by Dietmar Eggemann, Valentin
Schneider and Chuyi Zhou)
- Initialize the vruntime of a new task when it is first enqueued,
resulting in significant decrease in latency of newly woken tasks
(Zhang Qiao)
- Introduce SM_IDLE and an idle re-entry fast-path in __schedule()
(K Prateek Nayak, Peter Zijlstra)
- Clean up and clarify the usage of Clean up usage of rt_task()
(Qais Yousef)
- Preempt SCHED_IDLE entities in strict cgroup hierarchies
(Tianchen Ding)
- Clarify the documentation of time units for deadline scheduler
parameters (Christian Loehle)
- Remove the HZ_BW chicken-bit feature flag introduced a year ago,
the original change seems to be working fine (Phil Auld)
- Misc fixes and cleanups (Chen Yu, Dan Carpenter, Huang Shijie,
Peilin He, Qais Yousefm and Vincent Guittot)
* tag 'sched-core-2024-09-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (64 commits)
sched/cpufreq: Use NSEC_PER_MSEC for deadline task
cpufreq/cppc: Use NSEC_PER_MSEC for deadline task
sched/deadline: Clarify nanoseconds in uapi
sched/deadline: Convert schedtool example to chrt
sched/debug: Fix the runnable tasks output
sched: Fix sched_delayed vs sched_core
kernel/sched: Fix util_est accounting for DELAY_DEQUEUE
kthread: Fix task state in kthread worker if being frozen
sched/pelt: Use rq_clock_task() for hw_pressure
sched/fair: Move effective_cpu_util() and effective_cpu_util() in fair.c
sched/core: Introduce SM_IDLE and an idle re-entry fast-path in __schedule()
sched: Add put_prev_task(.next)
sched: Rework dl_server
sched: Combine the last put_prev_task() and the first set_next_task()
sched: Rework pick_next_task()
sched: Split up put_prev_task_balance()
sched: Clean up DL server vs core sched
sched: Fixup set_next_task() implementations
sched: Use set_next_task(.first) where required
sched/fair: Properly deactivate sched_delayed task upon class change
...
* Move the calculation of the AMD boost numerator outside of
amd-pstate, correcting acpi-cpufreq on systems with preferred cores
* Harden preferred core detection to avoid potential false positives
* Add extra unit test coverage for mode state machine
-----BEGIN PGP SIGNATURE-----
iQJOBAABCgA4FiEECwtuSU6dXvs5GA2aLRkspiR3AnYFAmbhviEaHG1hcmlvLmxp
bW9uY2llbGxvQGFtZC5jb20ACgkQLRkspiR3AnYqDA//TrvmXcpk1mnVJw3Y7MG0
/n8dsLpxqVtEf+USnlGR+iRhgSQ/W/Kr7b5a+jmdCwpHChuWHt2FnNgcHLIxDnZC
vmEJ02/2BCRoPKvcvV4VTh0ATu3O9nqwQiBVWBdNjDy+Dzr0pzA+SQopt1hCIsO2
mzUodhpiBqYKlMf/i6+aM1gZCGGqoRC40aGqnJsgegb61vl7zIc2ZcbTxUQlyTfv
t6J73IXLx8+YtrjejBYc7mRHhMQ2hCKy92C/8cNoGocj5faSKsAA3OUDcWq8qX0U
zK3GGGdW8MLHSbt3VyntstnfiLL7TnzowcjvrMudIWpjC1987GlE9BApbN9VRZ8e
ARN3Y7/ltjut/1fRB97BwjI9aDpzA0122Qzy4UOcK8o+be1eIr+ihV3Z9EN/snWg
0L/oq5+rGHvvIzf1BwGhoPSvgBIu7eMIYDcRxKPlEiKsbXrL4DdJC/nXgaZ/HiGO
eHx1dNy7LFrdnEwVI1frZWC6ZuZcpmOBdhnfU+leVxzB3Z++Qc266rsxKBsc5taZ
PPV18pxfbbl3iL85KDIbuBUCmA0aY8WEdCKtfXpl7zlB5g0fZQLyYeUbvahK08Sk
vyQAnPECbX/4v1Vx54Z70GPk0XD2+TXdg8yApnXrmRc36z/SLdprk5hPKbKhZu/r
iPxFUnvd0HCtjsLrsq/qUiQ=
=R4HZ
-----END PGP SIGNATURE-----
Merge tag 'amd-pstate-v6.12-2024-09-11' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/superm1/linux
Merge the second round of amd-pstate changes for 6.12 from Mario
Limonciello:
"* Move the calculation of the AMD boost numerator outside of
amd-pstate, correcting acpi-cpufreq on systems with preferred cores
* Harden preferred core detection to avoid potential false positives
* Add extra unit test coverage for mode state machine"
* tag 'amd-pstate-v6.12-2024-09-11' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/superm1/linux:
cpufreq/amd-pstate-ut: Fix an "Uninitialized variables" issue
cpufreq/amd-pstate-ut: Add test case for mode switches
cpufreq/amd-pstate: Export symbols for changing modes
amd-pstate: Add missing documentation for `amd_pstate_prefcore_ranking`
cpufreq: amd-pstate: Add documentation for `amd_pstate_hw_prefcore`
cpufreq: amd-pstate: Optimize amd_pstate_update_limits()
cpufreq: amd-pstate: Merge amd_pstate_highest_perf_set() into amd_get_boost_ratio_numerator()
x86/amd: Detect preferred cores in amd_get_boost_ratio_numerator()
x86/amd: Move amd_get_highest_perf() out of amd-pstate
ACPI: CPPC: Adjust debug messages in amd_set_max_freq_ratio() to warn
ACPI: CPPC: Drop check for non zero perf ratio
x86/amd: Rename amd_get_highest_perf() to amd_get_boost_ratio_numerator()
ACPI: CPPC: Adjust return code for inline functions in !CONFIG_ACPI_CPPC_LIB
x86/amd: Move amd_get_highest_perf() from amd.c to cppc.c
Using uninitialized value "mode2" when calling "amd_pstate_get_mode_string".
Set "mode2" to "AMD_PSTATE_DISABLE" by default.
Signed-off-by: Qianqiang Liu <qianqiang.liu@163.com>
Link: https://lore.kernel.org/r/20240910233923.46470-1-qianqiang.liu@163.com
Acked-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
There is a state machine in the amd-pstate driver utilized for
switches for all modes. To make sure that cleanup and setup works
properly for each mode add a unit test case that tries all
combinations.
Reviewed-by: Perry Yuan <perry.yuan@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
In order to effectively test all mode switch combinations export
everything necessarily for amd-pstate-ut to trigger a mode switch.
Reviewed-by: Perry Yuan <Perry.Yuan@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Don't take and release the mutex when prefcore isn't present and
avoid initialization of variables that will be initially set
in the function.
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Reviewed-by: Perry Yuan <perry.yuan@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
The special case in amd_pstate_highest_perf_set() is the value used
for calculating the boost numerator. Merge this into
amd_get_boost_ratio_numerator() and then use that to calculate boost
ratio.
This allows dropping more special casing of the highest perf value.
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
AMD systems that support preferred cores will use "166" as their
numerator for max frequency calculations instead of "255".
Add a function for detecting preferred cores by looking at the
highest perf value on all cores.
If preferred cores are enabled return 166 and if disabled the
value in the highest perf register. As the function will be called
multiple times, cache the values for the boost numerator and if
preferred cores will be enabled in global variables.
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
amd_pstate_get_highest_perf() is a helper used to get the highest perf
value on AMD systems. It's used in amd-pstate as part of preferred
core handling, but applicable for acpi-cpufreq as well.
Move it out to cppc handling code as amd_get_highest_perf().
Reviewed-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
The function name is ambiguous because it returns an intermediate value
for calculating maximum frequency rather than the CPPC 'Highest Perf'
register.
Rename the function to clarify its use and allow the function to return
errors. Adjust the consumer in acpi-cpufreq to catch errors.
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Convert the cppc deadline task attributes to use the available
definitions to make them more readable.
No functional change.
Signed-off-by: Christian Loehle <christian.loehle@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Juri Lelli <juri.lelli@redhat.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Link: https://lore.kernel.org/r/20240813144348.1180344-4-christian.loehle@arm.com
- Several OF related cleanups in cpufreq drivers (Rob Herring).
- Enable COMPILE_TEST for ARM drivers (Rob Herrring).
- Introduce quirks for syscon failures and use socinfo to get revision
for TI cpufreq driver (Dhruva Gole and Nishanth Menon).
- Minor cleanups in amd-pstate driver (Anastasia Belova and Dhananjay
Ugwekar).
- Minor cleanups for loongson, cpufreq-dt and powernv cpufreq drivers
(Danila Tikhonov, Huacai Chen, and Liu Jing).
-----BEGIN PGP SIGNATURE-----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=BlNP
-----END PGP SIGNATURE-----
Merge tag 'cpufreq-arm-updates-6.12' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Merge ARM cpufreq updates for 6.12 from Viresh Kumar:
"- Several OF related cleanups in cpufreq drivers (Rob Herring).
- Enable COMPILE_TEST for ARM drivers (Rob Herrring).
- Introduce quirks for syscon failures and use socinfo to get revision
for TI cpufreq driver (Dhruva Gole and Nishanth Menon).
- Minor cleanups in amd-pstate driver (Anastasia Belova and Dhananjay
Ugwekar).
- Minor cleanups for loongson, cpufreq-dt and powernv cpufreq drivers
(Danila Tikhonov, Huacai Chen, and Liu Jing)."
* tag 'cpufreq-arm-updates-6.12' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: ti-cpufreq: Use socinfo to get revision in AM62 family
cpufreq: Fix the cacography in powernv-cpufreq.c
cpufreq: ti-cpufreq: Introduce quirks to handle syscon fails appropriately
cpufreq: loongson3: Use raw_smp_processor_id() in do_service_request()
cpufreq: amd-pstate: add check for cpufreq_cpu_get's return value
cpufreq: Add SM7325 to cpufreq-dt-platdev blocklist
cpufreq: Fix warning on unused of_device_id tables for !CONFIG_OF
cpufreq/amd-pstate: Add the missing cpufreq_cpu_put()
cpufreq: Drop CONFIG_ARM and CONFIG_ARM64 dependency on Arm drivers
cpufreq: Enable COMPILE_TEST on Arm drivers
cpufreq: armada-8k: Avoid excessive stack usage
cpufreq: omap: Drop asm includes
cpufreq: qcom: Add explicit io.h include for readl/writel_relaxed
cpufreq: spear: Use of_property_for_each_u32() instead of open coding
cpufreq: Use of_property_present()
* Validate return of any attempt to update EPP limits, which fixes
the masking hardware problems.
-----BEGIN PGP SIGNATURE-----
iQJOBAABCgA4FiEECwtuSU6dXvs5GA2aLRkspiR3AnYFAmbYvoIaHG1hcmlvLmxp
bW9uY2llbGxvQGFtZC5jb20ACgkQLRkspiR3AnY6ZxAAw0vB5p/mC8QfS5VuDm0O
Up+dMtjVf9VcIOx4OoqSPNTY4HmNUnBSmACfeY/LzUa22BhM+7SJ74y8UoXGYGc8
GKzuVDRsbqnuMrGqbOd8u+eJhcc8fln7zJVa1xBOM8V5yHqvnxjAsnwVieVhjmKa
7m5K8ht/tJsCpaY/BjF7iHMgq950UGjO+pUXzrYP5ARV1O367DMWVQ91X9NBKwvN
w/mapWmH+mpp0//2hL7wzrtGIfYjdndFP3xM0+7v5MoEd9KuSl7xCVObGidDOEaz
oxfMCfPPpHMJLwD/L6VOwq/AIomJQVUZS8111ucnbdkIVW5QOlSaFwKJG/KmFvUQ
98lfX2xAaGB26tvWQ3l+vFQ7Qces0NrJfCLbpS2NdQ2oSq1+1ab3Yeh1wDXYph7o
hF+Xa/qJHzIFwzeQ2EmdXwthpoXbF5mmIiBZCTE/v1WpBVkYj+lJGtU+WsyAwFJT
qPASAqrRo8KoCfhdxYT47Rc3AowUWtHoJQlZNzTdbmc7KXrk+7NfDUZ5ifLq3puI
FAPWg76NM8aefoattsC57+6/V2bygbe1wIQaXRrybZiO9cMtY0eQ9bE4ysIm0ZQ8
bSPEHg1iYl3OrMzwRYnBHmev8E4jmKdKSnBBPSqD3ObeR3fNZQs1pxWc3CtHP8LA
p+AEE66CGAzsed5wudcEoOc=
=nPcu
-----END PGP SIGNATURE-----
Merge tag 'amd-pstate-v6.12-2024-09-04' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/superm1/linux
Merge an amd-pstate driver update for 6.12 from Mario Limonciello:
"amd-pstate development for 6.12:
* Validate return of any attempt to update EPP limits, which fixes
the masking hardware problems."
* tag 'amd-pstate-v6.12-2024-09-04' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/superm1/linux:
cpufreq/amd-pstate: Catch failures for amd_pstate_epp_update_limit()
amd_pstate_set_epp() calls cppc_set_epp_perf() which can fail for
a variety of reasons but this is ignored. Change the return flow
to allow failures.
Reviewed-by: Perry Yuan <perry.yuan@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
In the AM62x, AM62Ax, and AM62Px devices, we already have the revision
info within the k3-socinfo driver. Hence, re-use this information from
there instead of re using the offset for 2 drivers trying to get the
same information ie. revision.
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Commit b4bc9f9e27 ("cpufreq: ti-cpufreq: add support for omap34xx
and omap36xx") introduced special handling for OMAP3 class devices
where syscon node may not be present. However, this also creates a bug
where the syscon node is present, however the offset used to read
is beyond the syscon defined range.
Fix this by providing a quirk option that is populated when such
special handling is required. This allows proper failure for all other
platforms when the syscon node and efuse offsets are mismatched.
Fixes: b4bc9f9e27 ("cpufreq: ti-cpufreq: add support for omap34xx and omap36xx")
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Use raw_smp_processor_id() instead of plain smp_processor_id() in
do_service_request(), otherwise we may get some errors with the driver
enabled:
BUG: using smp_processor_id() in preemptible [00000000] code: (udev-worker)/208
caller is loongson3_cpufreq_probe+0x5c/0x250 [loongson3_cpufreq]
Reported-by: Xi Ruoyao <xry111@xry111.site>
Tested-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
cpufreq_cpu_get may return NULL. To avoid NULL-dereference check it
and return in case of error.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Anastasia Belova <abelova@astralinux.ru>
Reviewed-by: Perry Yuan <perry.yuan@amd.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The Qualcomm SM7325 platform uses the qcom-cpufreq-hw driver, so add
it to the cpufreq-dt-platdev driver's blocklist.
Signed-off-by: Danila Tikhonov <danila@jiaxyga.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
!CONFIG_OF builds cause warnings on unused of_device_id tables. This is
due to of_match_node() being a macro rather than static inline function.
Add a __maybe_unused annotation to the of_device_id tables.
Fixes: c7582ec85342 ("cpufreq: Drop CONFIG_ARM and CONFIG_ARM64 dependency on Arm drivers")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202408090714.wcrqU6Pk-lkp@intel.com/
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Fix the reference counting of cpufreq_policy object in amd_pstate_update()
function by adding the missing cpufreq_cpu_put().
Fixes: e8f555daac ("cpufreq/amd-pstate: fix setting policy current frequency value")
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Perry Yuan <perry.yuan@amd.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The CONFIG_ARM and CONFIG_ARM64 dependency is redundant as all the
drivers have necessary sub-arch dependency and don't depend on the
architecture support.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
COMPILE_TEST is useful for build testing without requiring a specific
architecture's compiler. Enable it for most of the Arm CPUFreq drivers.
As Kconfig.arm is only included on ARM and ARM64, COMPILE_TEST is only
enabled for those architectures until that is dropped.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Make intel_pstate use the HWP_HIGHEST_PERF values from
MSR_HWP_CAPABILITIES to set asymmetric CPU capacity information
via the previously introduced arch_set_cpu_capacity() on hybrid
systems without SMT.
Setting asymmetric CPU capacity is generally necessary to allow the
scheduler to compute task sizes in a consistent way across all CPUs
in a system where they differ by capacity. That, in turn, should help
to improve scheduling decisions. It is also necessary for the schedutil
cpufreq governor to operate as expected on hybrid systems where tasks
migrate between CPUs of different capacities.
The underlying observation is that intel_pstate already uses
MSR_HWP_CAPABILITIES to get CPU performance information which is
exposed by it via sysfs and CPU performance scaling is based on it.
Thus using this information for setting asymmetric CPU capacity is
consistent with what the driver has been doing already. Moreover,
HWP_HIGHEST_PERF reflects the maximum capacity of a given CPU including
both the instructions-per-cycle (IPC) factor and the maximum turbo
frequency and the units in which that value is expressed are the same
for all CPUs in the system, so the maximum capacity ratio between two
CPUs can be obtained by computing the ratio of their HWP_HIGHEST_PERF
values. Of course, in principle that capacity ratio need not be
directly applicable at lower frequencies, so using it for providing the
asymmetric CPU capacity information to the scheduler is a rough
approximation, but it is as good as it gets. Also, measurements
indicate that this approximation is not too bad in practice.
If the given system is hybrid and non-SMT, the new code disables ITMT
support in the scheduler (because it may get in the way of asymmetric CPU
capacity code in the scheduler that automatically gets enabled by setting
asymmetric CPU capacity) after initializing all online CPUs and finds
the one with the maximum HWP_HIGHEST_PERF value. Next, it computes the
capacity number for each (online) CPU by dividing the product of its
HWP_HIGHEST_PERF and SCHED_CAPACITY_SCALE by the maximum HWP_HIGHEST_PERF.
When a CPU goes offline, its capacity is reset to SCHED_CAPACITY_SCALE
and if it is the one with the maximum HWP_HIGHEST_PERF value, the
capacity numbers for all of the other online CPUs are recomputed. This
also takes care of a cleanup during driver operation mode changes.
Analogously, when a new CPU goes online, its capacity number is updated
and if its HWP_HIGHEST_PERF value is greater than the current maximum
one, the capacity numbers for all of the other online CPUs are
recomputed.
The case when the driver is notified of a CPU capacity change, either
through the HWP interrupt or through an ACPI notification, is handled
similarly to the CPU online case above, except that if the target CPU
is the current highest-capacity one and its capacity is reduced, the
capacity numbers for all of the other online CPUs need to be recomputed
either.
If the driver's "no_trubo" sysfs attribute is updated, all of the CPU
capacity information is computed from scratch to reflect the new turbo
status.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Tested-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com> # scale invariance
Link: https://patch.msgid.link/1979653.PYKUYFuaPT@rjwysocki.net
[ rjw: Fixed a typo in the changelog ]
[ rjw: Renamed 3 new functions and added a comment ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
commit bff7d13c19 ("cpufreq: amd-pstate: add debug message while
CPPC is supported and disabled by SBIOS") issues a warning on plaforms
where the X86_FEATURE_CPPC is expected to be enabled, but is not due
to it being disabled in the BIOS.
This feature bit corresponds to CPUID 0x80000008.ebx[27] which is a
reserved bit on the Zen1 processors and a reserved bit on Zen2 based
models 0x70-0x7F, and is expected to be cleared on these
platforms. Thus printing the warning message for these models when
X86_FEATURE_CPPC is unavailable is incorrect. Fix this.
Modify some of the comments, and use switch-case for model range
checking for improved readability while at it.
Fixes: bff7d13c19 ("cpufreq: amd-pstate: add debug message while CPPC is supported and disabled by SBIOS")
Cc: Xiaojian Du <xiaojian.du@amd.com>
Reported-by: David Wang <00107082@163.com>
Closes: https://lore.kernel.org/lkml/20240730140111.4491-1-00107082@163.com/
Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Acked-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
If a system is using preferred cores the highest perf will be inconsistent
as it can change from system events.
Skip the checks for it.
Fixes: e571a5e206 ("cpufreq: amd-pstate: Update amd-pstate preferred core ranking dynamically")
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
After the commit 63edbaa48a ("x86/cpu/topology: Add support for the
AMD 0x80000026 leaf"), the topolgy_logical_die_id() function returns
the logical Core Chiplet Die (CCD) ID instead of the logical socket
ID.
Since this is currently used to set MSR_AMD_CPPC_ENABLE, which needs
to be set on any one of the threads of the socket, it is prudent to
use topology_logical_package_id() in place of
topology_logical_die_id().
Fixes: 63edbaa48a ("x86/cpu/topology: Add support for the AMD 0x80000026 leaf")
cc: stable@vger.kernel.org # 6.10
Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Tested-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Link: https://lore.kernel.org/lkml/20240801124509.3650-1-Dhananjay.Ugwekar@amd.com/
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Smatch complains that "ret" could be uninitialized:
drivers/cpufreq/amd-pstate.c:734 amd_pstate_cpu_boost_update()
error: uninitialized symbol 'ret'.
This seems like it probably is a real issue. Initialize "ret" to zero to
be safe.
Fixes: c8c68c38b5 ("cpufreq: amd-pstate: initialize core precision boost state")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Perry Yuan <perry.yuan@amd.com>
Acked-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/lkml/7ff53543-6c04-48a0-8d99-7dc010b93b3a@stanley.mountain/T/
Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Prevent intel_pstate from loading when OOB (Out Of Band) P-states mode is
enabled.
The OOB identifying bits are same as for the prior generation CPUs like
Emerald Rapids servers. Add Granite Rapids and Sierra Forest CPU models to
intel_pstate_cpu_oob_ids[].
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20240802184839.1909091-1-srinivas.pandruvada@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In some build configurations (e.g. x86 allmodconfig), 2 cpu_mask
variables exceeds the max stack frame size:
drivers/cpufreq/armada-8k-cpufreq.c:203:1: error: the frame size of 2128 bytes is larger than 2048 bytes
Fix it by making "cpus" static which is fine given that module init is
only called once.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The omap driver doesn't actually need asm/smp_plat.h, so drop it.
asm/cpu.h is not needed either as linux/cpu.h is already included.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The qcom-cpufreq-hw driver is relying on an implicit include of io.h
which doesn't get included on some architectures.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Use of_property_count_u32_elems() and of_property_for_each_u32() instead
of of_find_property() and open coding the property parsing.
This is part of a larger effort to remove callers of of_find_property()
and similar functions. of_find_property() leaks the DT struct property
and data pointers which is a problem for dynamically allocated nodes
which may be freed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
[Viresh: Fixed build failure and initialize / increment 'i']
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Use of_property_present() to test for property presence rather than
of_(find|get)_property(). This is part of a larger effort to remove
callers of of_find_property() and similar functions. of_find_property()
leaks the DT struct property and data pointers which is a problem for
dynamically allocated nodes which may be freed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The current LATENCY_MULTIPLIER which has been around for nearly 20 years
causes rate_limit_us to be always in ms range.
On M1 mac mini I get 50 and 56us transition latency, but due to the 1000
multiplier we end up setting rate_limit_us to 50 and 56ms, which gets
capped into 2ms and was 10ms before e13aa799c2 ("cpufreq: Change
default transition delay to 2ms")
On Intel I5 system transition latency is 20us but due to the multiplier
we end up with 20ms that again is capped to 2ms.
Given how good modern hardware and how modern workloads require systems
to be more responsive to cater for sudden changes in workload (tasks
sleeping/wakeup/migrating, uclamp causing a sudden boost or cap) and
that 2ms is quarter of the time of 120Hz refresh rate system, drop the
old logic in favour of providing 50% headroom.
rate_limit_us = 1.5 * latency.
I considered not adding any headroom which could mean that we can end up
with infinite back-to-back requests.
I also considered providing a constant headroom (e.g: 100us) assuming
that any h/w or f/w dealing with the request shouldn't require a large
headroom when transition_latency is actually high.
But for both cases I wasn't sure if h/w or f/w can end up being
overwhelmed dealing with the freq requests in a potentially busy system.
So I opted for providing 50% breathing room.
This is expected to impact schedutil only as the other user,
dbs_governor, takes the max(2*tick, transition_delay_us) and the former
was at least 2ms on 1ms TICK, which is equivalent to the max_delay_us
before applying this patch. For systems with TICK of 4ms, this value
would have almost always ended up with 8ms sampling rate.
For systems that report 0 transition latency, we still default to
returning 1ms as transition delay.
This helps in eliminating a source of latency for applying requests as
mentioned in [1]. For example if we have a 1ms tick, most systems will
miss sending an update at tick when updating the util_avg for a task/CPU
(rate_limit_us will be 2ms for most systems).
Link: https://lore.kernel.org/lkml/20240724212255.mfr2ybiv2j2uqek7@airbuntu/ # [1]
Link: https://lore.kernel.org/lkml/20240205022500.2232124-1-qyousef@layalina.io/
Signed-off-by: Qais Yousef <qyousef@layalina.io>
Link: https://patch.msgid.link/20240728192659.58115-1-qyousef@layalina.io
[ rjw: Subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With ARCH=powerpc, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/cpufreq/ppc-cbe-cpufreq.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/cpufreq/powernv-cpufreq.o
Add the missing invocation of the MODULE_DESCRIPTION() macro to all
files which have a MODULE_LICENSE().
This includes three additional files which, although they did not
produce a warning with the powerpc allmodconfig configuration, may
cause this warning with specific options enabled in the kernel
configuration.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://patch.msgid.link/20240722-md-powerpc-drivers-cpufreq-v2-1-bb84d715eb3d@quicinc.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On Intel Emerald Rapids machines, we ship the Energy Performance Preference
(EPP) default for balance_performance as 128. However, during an internal
investigation together with Intel, we have determined that 32 is a more
suitable value. This leads to significant improvements in both performance
and energy:
POV-Ray: 32% faster | 12% less energy
OpenSSL: 12% faster | energy within 1%
Build Linux Kernel: 29% faster | 18% less energy
Therefore, we should move the default EPP for balance_performance to 32.
This is in line with what has already been done for Sapphire Rapids.
Signed-off-by: Pedro Henrique Kopper <pedro.kopper@canonical.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/Zqu6zjVMoiXwROBI@capivara
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Add Loongson-3 CPUFreq driver support (Huacai Chen).
- Add support for the Arrow Lake and Lunar Lake platforms and
the out-of-band (OOB) mode on Emerald Rapids to the intel_pstate
cpufreq driver, make it support the highest performance change
interrupt and clean it up (Srinivas Pandruvada).
- Switch cpufreq to new Intel CPU model defines (Tony Luck).
- Simplify the cpufreq driver interface by switching the .exit() driver
callback to the void return data type (Lizhe, Viresh Kumar).
- Make cpufreq_boost_enabled() return bool (Dhruva Gole).
- Add fast CPPC support to the amd-pstate cpufreq driver, address
multiple assorted issues in it and clean it up (Perry Yuan, Mario
Limonciello, Dhananjay Ugwekar, Meng Li, Xiaojian Du).
- Add Allwinner H700 speed bin to the sun50i cpufreq driver (Ryan
Walklin).
- Fix memory leaks and of_node_put() usage in the sun50i and qcom-nvmem
cpufreq drivers (Javier Carrasco).
- Clean up the sti and dt-platdev cpufreq drivers (Jeff Johnson,
Raphael Gallais-Pou).
- Fix deferred probe handling in the TI cpufreq driver and wrong return
values of ti_opp_supply_probe(), and add OPP tables for the AM62Ax and
AM62Px SoCs to it (Bryan Brattlof, Primoz Fiser).
- Avoid overflow of target_freq in .fast_switch() in the SCMI cpufreq
driver (Jagadeesh Kona).
- Use dev_err_probe() in every error path in probe in the Mediatek
cpufreq driver (Nícolas Prado).
- Fix kernel-doc param for longhaul_setstate in the longhaul cpufreq
driver (Yang Li).
- Fix system resume handling in the CPPC cpufreq driver (Riwen Lu).
- Improve the teo cpuidle governor and clean up leftover comments from
the menu cpuidle governor (Christian Loehle).
- Clean up a comment typo in the teo cpuidle governor (Atul Kumar
Pant).
- Add missing MODULE_DESCRIPTION() macro to cpuidle haltpoll (Jeff
Johnson).
- Switch the intel_idle driver to new Intel CPU model defines (Tony
Luck).
- Switch the Intel RAPL driver new Intel CPU model defines (Tony Luck).
- Simplify if condition in the idle_inject driver (Thorsten Blum).
- Fix missing cleanup on error in _opp_attach_genpd() (Viresh Kumar).
- Introduce an OF helper function to inform if required-opps is used
and drop a redundant in-parameter to _set_opp_level() (Ulf Hansson).
- Update pm-graph to v5.12 which includes fixes and major code revamp
for python3.12 (Todd Brandt).
- Address several assorted issues in the cpupower utility (Roman
Storozhenko).
-----BEGIN PGP SIGNATURE-----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=imBx
-----END PGP SIGNATURE-----
Merge tag 'pm-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These add a new cpufreq driver for Loongson-3, add support for new
features in the intel_pstate (Lunar Lake and Arrow Lake platforms, OOB
mode for Emerald Rapids, highest performance change interrupt),
amd-pstate (fast CPPC) and sun50i (Allwinner H700 speed bin) cpufreq
drivers, simplify the cpufreq driver interface, simplify the teo
cpuidle governor, adjust the pm-graph utility for a new version of
Python, address issues and clean up code.
Specifics:
- Add Loongson-3 CPUFreq driver support (Huacai Chen)
- Add support for the Arrow Lake and Lunar Lake platforms and the
out-of-band (OOB) mode on Emerald Rapids to the intel_pstate
cpufreq driver, make it support the highest performance change
interrupt and clean it up (Srinivas Pandruvada)
- Switch cpufreq to new Intel CPU model defines (Tony Luck)
- Simplify the cpufreq driver interface by switching the .exit()
driver callback to the void return data type (Lizhe, Viresh Kumar)
- Make cpufreq_boost_enabled() return bool (Dhruva Gole)
- Add fast CPPC support to the amd-pstate cpufreq driver, address
multiple assorted issues in it and clean it up (Perry Yuan, Mario
Limonciello, Dhananjay Ugwekar, Meng Li, Xiaojian Du)
- Add Allwinner H700 speed bin to the sun50i cpufreq driver (Ryan
Walklin)
- Fix memory leaks and of_node_put() usage in the sun50i and
qcom-nvmem cpufreq drivers (Javier Carrasco)
- Clean up the sti and dt-platdev cpufreq drivers (Jeff Johnson,
Raphael Gallais-Pou)
- Fix deferred probe handling in the TI cpufreq driver and wrong
return values of ti_opp_supply_probe(), and add OPP tables for the
AM62Ax and AM62Px SoCs to it (Bryan Brattlof, Primoz Fiser)
- Avoid overflow of target_freq in .fast_switch() in the SCMI cpufreq
driver (Jagadeesh Kona)
- Use dev_err_probe() in every error path in probe in the Mediatek
cpufreq driver (Nícolas Prado)
- Fix kernel-doc param for longhaul_setstate in the longhaul cpufreq
driver (Yang Li)
- Fix system resume handling in the CPPC cpufreq driver (Riwen Lu)
- Improve the teo cpuidle governor and clean up leftover comments
from the menu cpuidle governor (Christian Loehle)
- Clean up a comment typo in the teo cpuidle governor (Atul Kumar
Pant)
- Add missing MODULE_DESCRIPTION() macro to cpuidle haltpoll (Jeff
Johnson)
- Switch the intel_idle driver to new Intel CPU model defines (Tony
Luck)
- Switch the Intel RAPL driver new Intel CPU model defines (Tony
Luck)
- Simplify if condition in the idle_inject driver (Thorsten Blum)
- Fix missing cleanup on error in _opp_attach_genpd() (Viresh Kumar)
- Introduce an OF helper function to inform if required-opps is used
and drop a redundant in-parameter to _set_opp_level() (Ulf Hansson)
- Update pm-graph to v5.12 which includes fixes and major code revamp
for python3.12 (Todd Brandt)
- Address several assorted issues in the cpupower utility (Roman
Storozhenko)"
* tag 'pm-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (77 commits)
cpufreq: sti: fix build warning
cpufreq: mediatek: Use dev_err_probe in every error path in probe
cpufreq: Add Loongson-3 CPUFreq driver support
cpufreq: Make cpufreq_driver->exit() return void
cpufreq/amd-pstate: Fix the scaling_max_freq setting on shared memory CPPC systems
cpufreq/amd-pstate-ut: Convert nominal_freq to khz during comparisons
cpufreq: pcc: Remove empty exit() callback
cpufreq: loongson2: Remove empty exit() callback
cpufreq: nforce2: Remove empty exit() callback
cpupower: fix lib default installation path
cpufreq: docs: Add missing scaling_available_frequencies description
cpuidle: teo: Don't count non-existent intercepts
cpupower: Disable direct build of the 'bench' subproject
cpuidle: teo: Remove recent intercepts metric
Revert: "cpuidle: teo: Introduce util-awareness"
cpufreq: make cpufreq_boost_enabled() return bool
cpufreq: intel_pstate: Support highest performance change interrupt
x86/cpufeatures: Add HWP highest perf change feature flag
Documentation: cpufreq: amd-pstate: update doc for Per CPU boost control method
cpufreq: amd-pstate: Cap the CPPC.max_perf to nominal_perf if CPB is off
...
The updates to the mediatek, allwinner, ti, tegra, microchip, stm32,
samsung, imx, zynq and amlogic platoforms are farily small maintenance
changes, either addressing minor mistakes or enabling additional hardware.
The qualcomm platform changes add a number of features and are larger
than the other ones combined, introducing the use of linux/cleanup.h
across several drivers, adding support for Snapdragon X1E and other
SoCs in platform drivers, a new "protection domain mapper" driver, and a
"shared memory bridge" driver.
The cznic "turris omnia" router based on Marvell Armada gets a platform
driver that talks to the board specific microcontroller.
The reset and cache subsystems get a few minor updates to SoC specific
drivers, while the ff-a, scmi and optee firmware drivers get some
code refactoring and new features.
-----BEGIN PGP SIGNATURE-----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=ChcR
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"The updates to the mediatek, allwinner, ti, tegra, microchip, stm32,
samsung, imx, zynq and amlogic platoforms are fairly small maintenance
changes, either addressing minor mistakes or enabling additional
hardware.
The qualcomm platform changes add a number of features and are larger
than the other ones combined, introducing the use of linux/cleanup.h
across several drivers, adding support for Snapdragon X1E and other
SoCs in platform drivers, a new "protection domain mapper" driver, and
a "shared memory bridge" driver.
The cznic "turris omnia" router based on Marvell Armada gets a
platform driver that talks to the board specific microcontroller.
The reset and cache subsystems get a few minor updates to SoC specific
drivers, while the ff-a, scmi and optee firmware drivers get some code
refactoring and new features"
* tag 'soc-drivers-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (122 commits)
firmware: turris-mox-rwtm: Initialize completion before mailbox
firmware: turris-mox-rwtm: Fix checking return value of wait_for_completion_timeout()
firmware: turris-mox-rwtm: Do not complete if there are no waiters
MAINTAINERS: drop riscv list from cache controllers
platform: cznic: turris-omnia-mcu: fix Kconfig dependencies
bus: sunxi-rsb: Constify struct regmap_bus
soc: sunxi: sram: Constify struct regmap_config
platform: cznic: turris-omnia-mcu: Depend on WATCHDOG
platform: cznic: turris-omnia-mcu: Depend on OF
soc: samsung: exynos-pmu: add support for PMU_ALIVE non atomic registers
arm64: stm32: enable scmi regulator for stm32
firmware: qcom: tzmem: blacklist more platforms for SHM Bridge
soc: qcom: wcnss: simplify with cleanup.h
soc: qcom: pdr: simplify with cleanup.h
soc: qcom: ocmem: simplify with cleanup.h
soc: qcom: mdt_loader: simplify with cleanup.h
soc: qcom: llcc: simplify with cleanup.h
firmware: qcom: tzmem: simplify returning pointer without cleanup
soc: qcom: socinfo: Add PM6350 PMIC
arm64: dts: renesas: rz-smarc: Replace fixed regulator for USB VBUS
...
Support for Shared Memory (shm) Bridge is added, which provides a
stricter interface for handling of buffers passed to TrustZone.
The X1Elite platform is added to uefisecapp allow list, to instantiate
the efivars implementation.
A new in-kernel implementation of the pd-mapper (or servreg) service is
introduced, to replace the userspace dependency for USB Type-C and
battery management.
Support for sharing interrupts across multiple bwmon instances is added,
and a refcount imbalance issue is corrected.
The LLCC support for recent platforms is corrected, and SA8775P support
is added.
A new interface is added to SMEM, to expose "feature codes". One example
of the usecase for this is to indicate to the GPU driver which
frequencies are available on the given device.
The interrupt consumer and provider side of SMP2P is updated to provide
more useful names in interrupt stats.
Support for using the mailbox binding and driver for outgoing IPC
interrupt in the SMSM driver is introduced.
socinfo driver learns about SDM670 and IPQ5321, as well as get some
updates to the X1E PMICs.
pmic_glink is bumped to now support managing 3 USB Type-C ports.
-----BEGIN PGP SIGNATURE-----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=Eknv
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=lPdX
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/drivers
Qualcomm driver updates for v6.11
Support for Shared Memory (shm) Bridge is added, which provides a
stricter interface for handling of buffers passed to TrustZone.
The X1Elite platform is added to uefisecapp allow list, to instantiate
the efivars implementation.
A new in-kernel implementation of the pd-mapper (or servreg) service is
introduced, to replace the userspace dependency for USB Type-C and
battery management.
Support for sharing interrupts across multiple bwmon instances is added,
and a refcount imbalance issue is corrected.
The LLCC support for recent platforms is corrected, and SA8775P support
is added.
A new interface is added to SMEM, to expose "feature codes". One example
of the usecase for this is to indicate to the GPU driver which
frequencies are available on the given device.
The interrupt consumer and provider side of SMP2P is updated to provide
more useful names in interrupt stats.
Support for using the mailbox binding and driver for outgoing IPC
interrupt in the SMSM driver is introduced.
socinfo driver learns about SDM670 and IPQ5321, as well as get some
updates to the X1E PMICs.
pmic_glink is bumped to now support managing 3 USB Type-C ports.
* tag 'qcom-drivers-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (48 commits)
soc: qcom: smp2p: Use devname for interrupt descriptions
soc: qcom: smsm: Add missing mailbox dependency to Kconfig
soc: qcom: add missing pd-mapper dependencies
soc: qcom: icc-bwmon: Allow for interrupts to be shared across instances
dt-bindings: interconnect: qcom,msm8998-bwmon: Add X1E80100 BWMON instances
dt-bindings: interconnect: qcom,msm8998-bwmon: Remove opp-table from the required list
firmware: qcom: tzmem: export devm_qcom_tzmem_pool_new()
soc: qcom: add pd-mapper implementation
soc: qcom: pdr: extract PDR message marshalling data
soc: qcom: pdr: fix parsing of domains lists
soc: qcom: pdr: protect locator_addr with the main mutex
firmware: qcom: scm: clarify the comment in qcom_scm_pas_init_image()
firmware: qcom: scm: add support for SHM bridge memory carveout
firmware: qcom: tzmem: enable SHM Bridge support
firmware: qcom: scm: add support for SHM bridge operations
firmware: qcom: qseecom: convert to using the TZ allocator
firmware: qcom: scm: make qcom_scm_qseecom_app_get_id() use the TZ allocator
firmware: qcom: scm: make qcom_scm_lmh_dcvsh() use the TZ allocator
firmware: qcom: scm: make qcom_scm_ice_set_key() use the TZ allocator
firmware: qcom: scm: make qcom_scm_assign_mem() use the TZ allocator
...
Link: https://lore.kernel.org/r/20240705034410.13968-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Building this driver yields the following:
.../drivers/cpufreq/sti-cpufreq.c:215:50: warning: ‘%d’ directive output may be truncated writing between 1 and 10 bytes into a region of size 2 [-Wformat-truncation=]
215 | snprintf(name, MAX_PCODE_NAME_LEN, pcode%d, pcode);
| ^~
.../drivers/cpufreq/sti-cpufreq.c:215:44: note: directive argument in the range [0, 2147483647]
215 | snprintf(name, MAX_PCODE_NAME_LEN, pcode%d, pcode);
| ^~~~~~~~~
.../drivers/cpufreq/sti-cpufreq.c:215:9: note: ‘snprintf’ output between 7 and 16 bytes into a destination of size 7
215 | snprintf(name, MAX_PCODE_NAME_LEN, pcode%d, pcode);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix the buffer size to avoid the warning at build time.
Signed-off-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Use the dev_err_probe() helper to log the errors on every error path in
the probe function and its sub-functions. This includes
* adding error messages where there was none
* converting over dev_err/dev_warn
* removing the top-level error message after mtk_cpu_dvfs_info_init() is
called, since every error path inside that function already logs the
error reason. This gets rid of the misleading error message when probe
is deferred:
mtk-cpufreq mtk-cpufreq: failed to initialize dvfs info for cpu0
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Some of LoongArch processors (Loongson-3 series) support DVFS, their
IOCSR.FEATURES has IOCSRF_FREQSCALE set. And they has a micro-core in
the package called SMC (System Management Controller), which can be
used to detect temperature, control fans, scale frequency and voltage,
etc.
The Loongson-3 CPUFreq driver is very simple now, it communicate with
SMC, get DVFS info, set target frequency from CPUFreq core, and so on.
There is a command list to interact with SMC, widely-used commands in
the CPUFreq driver include:
CMD_GET_VERSION: Get SMC firmware version.
CMD_GET_FEATURE: Get enabled SMC features.
CMD_SET_FEATURE: Enable SMC features, such as basic DVFS, BOOST.
CMD_GET_FREQ_LEVEL_NUM: Get the number of all frequency levels.
CMD_GET_FREQ_BOOST_LEVEL: Get the first boost frequency level.
CMD_GET_FREQ_LEVEL_INFO: Get the detail info of a frequency level.
CMD_GET_FREQ_INFO: Get the current frequency.
CMD_SET_FREQ_INFO: Set the target frequency.
In future we will add automatic frequency scaling, which is similar to
Intel's HWP (HardWare P-State).
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
[ Viresh: Minor formatting cleanups, change return type of exit() to
void and use devm_mutex_init() ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The cpufreq core doesn't check the return type of the exit() callback
and there is not much the core can do on failures at that point. Just
drop the returned value and make it return void.
Signed-off-by: Lizhe <sensor1010@163.com>
[ Viresh: Reworked the patches to fix all missing changes together. ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> # Mediatek
Acked-by: Sudeep Holla <sudeep.holla@arm.com> # scpi, scmi, vexpress
Acked-by: Mario Limonciello <mario.limonciello@amd.com> # amd
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> # bmips
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com> # omap
This adds fixes for setting scaling max frequency on systems
without a dedicated MSR for setting CPPC requests.
-----BEGIN PGP SIGNATURE-----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=KOPt
-----END PGP SIGNATURE-----
Merge tag 'amd-pstate-v6.11-2024-07-07' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/superm1/linux
Merge more amd-pstate changes for 6.11 from Mario Liminciello:
"This adds fixes for setting scaling max frequency on systems
without a dedicated MSR for setting CPPC requests."
* tag 'amd-pstate-v6.11-2024-07-07' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/superm1/linux:
cpufreq/amd-pstate: Fix the scaling_max_freq setting on shared memory CPPC systems
cpufreq/amd-pstate-ut: Convert nominal_freq to khz during comparisons
On shared memory CPPC systems, with amd_pstate=active mode, the change
in scaling_max_freq doesn't get written to the shared memory
region. Due to this, the writes to the scaling_max_freq sysfs file
don't take effect. Fix this by propagating the scaling_max_freq
changes to the shared memory region.
Fixes: ffa5096a7c ("cpufreq: amd-pstate: implement Pstate EPP support for the AMD processors")
Reported-by: David Arcari <darcari@redhat.com>
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20240702081413.5688-3-Dhananjay.Ugwekar@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
cpudata->nominal_freq being in MHz whereas other frequencies being in
KHz breaks the amd-pstate-ut frequency sanity check. This fixes it.
Fixes: e4731baaf2 ("cpufreq: amd-pstate: Fix the inconsistency in max frequency units")
Reported-by: David Arcari <darcari@redhat.com>
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/20240702081413.5688-2-Dhananjay.Ugwekar@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
The exit() callback is optional, remove the empty one.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
The exit() callback is optional, remove the empty one.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
The exit() callback is optional, remove the empty one.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
When boost is set for CPUs using acpi-cpufreq, the policy is not
updated which can cause boost to be incorrectly not reported.
Fixes: 218a06a79d ("cpufreq: Support per-policy performance boost")
Link: https://patch.msgid.link/20240626204723.6237-2-mario.limonciello@amd.com
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Suggested-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The behavior introduced in commit f37a4d6b4a ("cpufreq: Fix per-policy
boost behavior on SoCs using cpufreq_boost_set_sw()") sets up the boost
policy incorrectly when boost has been enabled by the platform firmware
initially even if a driver sets the policy up.
This is because policy_has_boost_freq() assumes that there is a frequency
table set up by the driver and that the boost frequencies are advertised
in that table. This assumption doesn't work for acpi-cpufreq or
amd-pstate. Only use this check to enable boost if it's not already
enabled instead of also disabling it if alreayd enabled.
Fixes: f37a4d6b4a ("cpufreq: Fix per-policy boost behavior on SoCs using cpufreq_boost_set_sw()")
Link: https://patch.msgid.link/20240626204723.6237-1-mario.limonciello@amd.com
Reviewed-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Suggested-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since this function is supposed to return boost_enabled which is anyway
a bool type make sure that it's return value is also marked as bool.
This helps maintain better consistency in data types being used.
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://patch.msgid.link/20240627060117.1809477-1-d-gole@ti.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On some systems, the HWP (Hardware P-states) highest performance level
can change from the value set at boot-up. This behavior can lead to two
issues:
- The 'cpuinfo_max_freq' within the 'cpufreq' sysfs will not reflect
the CPU's highest achievable performance.
- Even if the CPU's highest performance level is increased after booting,
the CPU may not reach the full expected performance.
The availability of this feature is indicated by the CPUID instruction:
if CPUID[6].EAX[15] is set to 1, the feature is supported. When supported,
setting bit 2 of the MSR_HWP_INTERRUPT register enables notifications of
the highest performance level changes. Therefore, as part of enabling the
HWP interrupt, bit 2 of the MSR_HWP_INTERRUPT should also be set when this
feature is supported.
Upon a change in the highest performance level, a new HWP interrupt is
generated, with bit 3 of the MSR_HWP_STATUS register set, and the
MSR_HWP_CAPABILITIES register is updated with the new highest performance
limit.
The processing of the interrupt is the same as the guaranteed performance
change. Notify change to cpufreq core and update MSR_HWP_REQUEST with new
performance limits.
The current driver implementation already takes care of the highest
performance change as part of:
commit dfeeedc1bf ("cpufreq: intel_pstate: Update cpuinfo.max_freq
on HWP_CAP changes")
For example:
Before highest performance change interrupt:
cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
3700000
cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_max_freq
3700000
After highest performance changes interrupt:
cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_max_freq
3900000
cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
3900000
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20240624161109.1427640-3-srinivas.pandruvada@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
allows controlling which CPU cores can operate above nominal
frequencies for short periods of time.
-----BEGIN PGP SIGNATURE-----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=EZq/
-----END PGP SIGNATURE-----
Merge tag 'amd-pstate-v6.11-2024-06-26' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/superm1/linux
Merge more amd-pstate driver updates for 6.11 from Mario Limonciello:
"Add support for amd-pstate core performance boost support which
allows controlling which CPU cores can operate above nominal
frequencies for short periods of time."
* tag 'amd-pstate-v6.11-2024-06-26' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/superm1/linux:
Documentation: cpufreq: amd-pstate: update doc for Per CPU boost control method
cpufreq: amd-pstate: Cap the CPPC.max_perf to nominal_perf if CPB is off
cpufreq: amd-pstate: initialize core precision boost state
cpufreq: acpi: move MSR_K7_HWCR_CPB_DIS_BIT into msr-index.h
When Core Performance Boost is disabled by the user, the
CPPC_REQ.max_perf should not exceed the nominal_perf since by definition
the frequencies between nominal_perf and the highest_perf are in the
boost range. Fix this in amd_pstate_update()
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Perry Yuan <Perry.Yuan@amd.com>
Link: https://lore.kernel.org/r/66f55232be01092c423f0523f68b82b80c293943.1718988436.git.perry.yuan@amd.com
Link: https://lore.kernel.org/r/20240626042733.3747-4-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
The "Core Performance Boost (CPB) feature, when enabled in the BIOS,
allows the OS to control the highest performance for each individual
core. The active, passive and the guided modes of the amd-pstate driver
do support controlling the core frequency boost when this BIOS feature
is enabled. Additionally, the amd-pstate driver provides a sysfs
interface allowing the user to activate/deactivate this core performance
boost feature at runtime.
Add support for the set_boost callback in the active mode driver to
enable boost control via the cpufreq core. This ensures a consistent
boost control interface across all pstate modes, including passive
mode, guided mode, and active mode.
With this addition, all three pstate modes can support the same boost
control interface with unique interface and global CPB control. Each
CPU also supports individual boost control, allowing global CPB to
change all cores' boost states simultaneously. Specific CPUs can
update their boost states separately, ensuring all cores' boost
states are synchronized.
Cc: Oleksandr Natalenko <oleksandr@natalenko.name>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217931
Signed-off-by: Perry Yuan <Perry.Yuan@amd.com>
Co-developed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/20240626042733.3747-3-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
'st,stih418' is missing in the compatible list.
Add it in order to use the driver with stih418 platform.
Signed-off-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
* Enables amd-pstate by default in "shared memory" designs without a dedicated MSR.
* Adds extra infrastructure for debugging problems.
* Bug fixes found for init/unload failure
-----BEGIN PGP SIGNATURE-----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=Eea8
-----END PGP SIGNATURE-----
Merge tag 'amd-pstate-v6.11-2024-06-24' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/superm1/linux
Merge the second round of changes for amd-pstate in 6.11 from Mario
Limonciello:
"* Enables amd-pstate by default in "shared memory" designs without
a dedicated MSR.
* Adds extra infrastructure for debugging problems.
* Bug fixes found for init/unload failure."
* tag 'amd-pstate-v6.11-2024-06-24' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/superm1/linux:
cpufreq: simplify boolean parsing with kstrtobool in store function
cpufreq: amd-pstate: Don't create attributes when registration fails
cpufreq: amd-pstate: Make amd-pstate unit tests depend on amd-pstate
cpufreq/amd-pstate: fix setting policy current frequency value
cpufreq: amd-pstate: auto-load pstate driver by default
cpufreq: amd-pstate: enable shared memory type CPPC by default
cpufreq: amd-pstate: switch boot_cpu_has() to cpu_feature_enabled()
Documentation: PM: amd-pstate: add guided mode to the Operation mode
cpufreq: amd-pstate: add debug message while CPPC is supported and disabled by SBIOS
cpufreq: amd-pstate: show CPPC debug message if CPPC is not supported
cpufreq: amd-pstate: remove unused variable nominal_freq
cpufreq: amd-pstate: optimize the initial frequency values verification
cpufreq: amd-pstate: Allow users to write 'default' EPP string
More speed grades for the AM62Px SoC family have been defined which
unfortunately no longer align with the AM62x table. So create a new
table with these new speed grades defined for the AM62Px
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
As the AM62Ax SoC family matures more speed grades are being defined.
These new grades unfortunately no longer align with the AM62x SoC
family. Define a new table with new OPP speed grade limits for the
AM62Ax
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Update the cpufreq store function to use kstrtobool for parsing boolean
values. This simplifies the code and improves readability by using a
standard kernel function for boolean string conversion.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Link: https://lore.kernel.org/r/d392eba3bad1231776124c321cef8c184ce1482d.1718988436.git.perry.yuan@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
It is reported that single-thread performance on some hybrid systems
dropped significantly after commit 7feec7430e ("ACPI: CPPC: Only probe
for _CPC if CPPC v2 is acked") which prevented _CPC from being used if
the support for it had not been confirmed by the platform firmware.
The problem is that if the platform firmware does not confirm CPPC v2
support, cppc_get_perf_caps() returns an error which prevents the
intel_pstate driver from enabling ITMT. Consequently, the scheduler
does not get any hints on CPU performance differences, so in a hybrid
system some tasks may run on CPUs with lower capacity even though they
should be running on high-capacity CPUs.
To address this, modify intel_pstate to use the information from
MSR_HWP_CAPABILITIES to enable ITMT if CPPC is not available (which is
done already if the highest performance number coming from CPPC is not
realistic).
Fixes: 7feec7430e ("ACPI: CPPC: Only probe for _CPC if CPPC v2 is acked")
Closes: https://lore.kernel.org/linux-acpi/d01b0a1f-bd33-47fe-ab41-43843d8a374f@kfocus.org
Link: https://lore.kernel.org/linux-acpi/ZnD22b3Br1ng7alf@kf-XE
Reported-by: Aaron Rainbolt <arainbolt@kfocus.org>
Tested-by: Aaron Rainbolt <arainbolt@kfocus.org>
Cc: 5.19+ <stable@vger.kernel.org> # 5.19+
Link: https://patch.msgid.link/12460110.O9o76ZdvQC@rjwysocki.net
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
If driver registration fails then immediately return the failure
instead of continuing to register attributes.
This fixes issues of falling back from amd-pstate to other drivers
when cpufreq init has failed for any reason.
Reported-by: alex.s.cochran@proton.me
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Reviewed-by: Perry Yuan <Perry.Yuan@amd.com>
Link: https://lore.kernel.org/r/20240623200918.52104-1-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
When scaling min/max freq values were being setted,
the value of policy->cur need to update.
Signed-off-by: Meng Li <li.meng@amd.com>
Acked-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20240227071133.3405003-1-li.meng@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
If the `amd-pstate` driver is not loaded automatically by default,
it is because the kernel command line parameter has not been added.
To resolve this issue, it is necessary to call the `amd_pstate_set_driver()`
function to enable the desired mode (passive/active/guided) before registering
the driver instance.
This ensures that the driver is loaded correctly without relying on the kernel
command line parameter.
When there is no parameter added to command line, Kernel config will
provide the default mode to load.
Meanwhile, user can add driver mode in command line which will override
the kernel config default option.
Reported-by: Andrei Amuraritei <andamu@posteo.net>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218705
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/83301c4cea4f92fb19e14b23f2bac7facfd8bdbb.1718811234.git.perry.yuan@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
The amd-pstate-epp driver has been implemented and resolves the
performance drop issue seen in passive mode for shared memory type
CPPC systems. Users who enable the active mode driver will not
experience a performance drop compared to the passive mode driver.
Therefore, the EPP driver should be loaded by default for shared
memory type CPPC system to get better performance.
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/c705507cf3ee790e544251cfd897ed11e8e57712.1718811234.git.perry.yuan@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
replace the usage of the deprecated boot_cpu_has() function with
the modern cpu_feature_enabled() function. The switch to cpu_feature_enabled()
ensures compatibility with the latest CPU feature detection mechanisms and
improves code maintainability.
Acked-by: Mario Limonciello <mario.limonciello@amd.com>
Suggested-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/f1567593ac5e1d38343067e9c681a8c4b0707038.1718811234.git.perry.yuan@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
If CPPC feature is supported by the CPU however the CPUID flag bit is not
set by SBIOS, the `amd_pstate` will be failed to load while system
booting.
So adding one more debug message to inform user to check the SBIOS setting,
The change also can help maintainers to debug why amd_pstate driver failed
to be loaded at system booting if the processor support CPPC.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218686
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Acked-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/42c953616ac121bd1e5c329e83d015a02e6b32c7.1718811234.git.perry.yuan@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
To enhance the debugging capability of the driver loading failure for
broken CPPC ACPI tables, it can optimize the expression by moving the
verification of `min_freq`, `nominal_freq`, and other dependency values
to the `amd_pstate_init_freq()` function where they are initialized.
If any of these values are incorrect, the `amd-pstate` driver will not be registered.
By ensuring that these values are correct before they are used, it will facilitate
the debugging process when encountering driver loading failures due to faulty CPPC
ACPI tables from BIOS
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Acked-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Acked-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/f9793f8451c1832e34cc9dc35f89c653b39cfe38.1718811234.git.perry.yuan@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
The EPP string for 'default' represents what the firmware had configured
as the default EPP value but once a user changes EPP to another string
they can't reset it back to 'default'.
Cache the firmware EPP value and allow the user to write 'default' using
this value.
Reported-by: Artem S. Tashkinov <aros@gmx.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217931#c61
Reviewed-by: Perry Yuan <perry.yuan@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Replace sprintf() and scnprintf() with sysfs_emit() and sysfs_emit_at()
in the cpufreq core.
This ensures safer buffer handling and consistency with sysfs interfaces.
Update show_scaling_available_governors() and related functions for
compliance with the new API.
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://patch.msgid.link/20240619081520.259971-1-perry.yuan@amd.com
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Support for the Allwinner H618, H618 and H700 was added to the sun50i
cpufreq-nvmem driver recently [1] however at the time some operating
points supported by the H700 (1.008, 1.032 and 1.512 GHz) and in use by
vendor BSPs were found to be unstable during testing, so the H700 speed
bin and the 1.032 GHz OPP were not included in the mainline driver.
Retesting with kernel 6.10rc2 (which carries additional fixes for the
driver) now shows stable operation with these points.
Add the H700 speed bin to the driver.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Ryan Walklin <ryan@testtoast.com>
--
[1] https://lore.kernel.org/linux-sunxi/20240418154408.1740047-1-andre.przywara@arm.com
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
loop for passive mode.
-----BEGIN PGP SIGNATURE-----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=6763
-----END PGP SIGNATURE-----
Merge tag 'amd-pstate-v6.11-2024-06-11' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/superm1/linux
Merge amd-pstate driver updates for v6.11 from Mario Mario Limonciello:
"Add support for "Fast CPPC" which allows some CPUs to operate a tighter
loop for passive mode."
* tag 'amd-pstate-v6.11-2024-06-11' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/superm1/linux:
cpufreq: amd-pstate: change cpu freq transition delay for some models
x86/cpufeatures: Add AMD FAST CPPC feature flag
There is a corner case where the desired_perf is exactly same as the old
perf, but the actual current freq is not.
This happens during S3 while the cpufreq governor is set to powersave.
During cpufreq resume process, the booting CPU's new_freq obtained via
.get() is the highest frequency, while the policy->cur and
cpu->perf_ctrls.desired_perf are set to the lowest level (powersave
governor). This causes the warning: "CPU frequency out of sync:", and
the cpufreq core sets policy->cur to new_freq.
Then the governor->limits() calls cppc_cpufreq_set_target() to
configures the CPU frequency and returns directly because the
desired_perf converted from target_freq is same as the
cpu->perf_ctrls.desired_perf and both are the lowest_perf.
Since target_freq and policy->cur have been already compared in
__cpufreq_driver_target(), there's no need to compare them again here.
Drop the comparison.
Signed-off-by: Riwen Lu <luriwen@kylinos.cn>
[ Viresh: Updated commit message / subject ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
After recent changes in intel_pstate, global.turbo_disabled is only set
at the initialization time and never changed. However, it turns out
that on some systems the "turbo disabled" bit in MSR_IA32_MISC_ENABLE,
the initial state of which is reflected by global.turbo_disabled, can be
flipped later and there should be a way to take that into account (other
than checking that MSR every time the driver runs which is costly and
useless overhead on the vast majority of systems).
For this purpose, notice that before the changes in question,
store_no_turbo() contained a turbo_is_disabled() check that was used
for updating global.turbo_disabled if the "turbo disabled" bit in
MSR_IA32_MISC_ENABLE had been flipped and that functionality can be
restored. Then, users will be able to reset global.turbo_disabled
by writing 0 to no_turbo which used to work before on systems with
flipping "turbo disabled" bit.
This guarantees the driver state to remain in sync, but READ_ONCE()
annotations need to be added in two places where global.turbo_disabled
is accessed locklessly, so modify the driver to make that happen.
Fixes: 0940f1a801 ("cpufreq: intel_pstate: Do not update global.turbo_disabled after initialization")
Closes: https://lore.kernel.org/linux-pm/bf3ebf1571a4788e97daf861eb493c12d42639a3.camel@xry111.site
Suggested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reported-by: Xi Ruoyao <xry111@xry111.site>
Tested-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Prevent intel_pstate from loading when OOB (Out Of Band) P-states mode is
enabled in Emerald Rapids.
The OOB identifying bits are same as for the prior generation CPUs
like Sapphire Rapids servers, so also add Emerald Rapids to the
intel_pstate_cpu_oob_ids[] list.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use the same default EPPs as Meteor Lake generation.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Update the default balance_performance EPP to 64. This gives better
performance and also perf/watt compared to current value of 115.
For example:
Speedometer 2.1
score: +19%
Perf/watt: +5.25%
Webxprt 4 score
score: +12%
Perf/watt: +6.12%
3DMark Wildlife extreme unlimited score
score: +3.2%
Perf/watt: +11.5%
Geekbench6 MT
score: +2.14%
Perf/watt: +0.32%
Also update balance_power EPP default to 179. With this change:
Video Playback power is reduced by 52%
Team video conference power is reduced by 35%
With Power profile daemon now sets balance_power EPP on DC instead of
balance_performance, updating balance_power EPP will help to extend
battery life.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
New CPU #defines encode vendor and family as well as model.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
New CPU #defines encode vendor and family as well as model.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Handle deferred probing gracefully by using dev_err_probe() to not
spam console with unnecessary error messages.
Fixes: f88d152dc7 ("cpufreq: ti: Migrate to dev_pm_opp_set_config()")
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Fix unchecked MSR access error for processors with no HWP support. On
such processors, maximum frequency can be changed by the system firmware
using ACPI event ACPI_PROCESSOR_NOTIFY_HIGEST_PERF_CHANGED. This results
in accessing HWP MSR 0x771.
Call Trace:
<TASK>
generic_exec_single+0x58/0x120
smp_call_function_single+0xbf/0x110
rdmsrl_on_cpu+0x46/0x60
intel_pstate_get_hwp_cap+0x1b/0x70
intel_pstate_update_limits+0x2a/0x60
acpi_processor_notify+0xb7/0x140
acpi_ev_notify_dispatch+0x3b/0x60
HWP MSR 0x771 can be only read on a CPU which supports HWP and enabled.
Hence intel_pstate_get_hwp_cap() can only be called when hwp_active is
true.
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Closes: https://lore.kernel.org/linux-pm/20240529155740.Hq2Hw7be@linutronix.de/
Fixes: e8217b4bec ("cpufreq: intel_pstate: Update the maximum CPU frequency consistently")
Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/cpufreq/cpufreq-dt-platdev.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The nominal frequency in cpudata is maintained in MHz whereas all other
frequencies are in KHz. This means we have to convert nominal frequency
value to KHz before we do any interaction with other frequency values.
In amd_pstate_set_boost(), this conversion from MHz to KHz is missed,
fix that.
Tested on a AMD Zen4 EPYC server
Before:
$ cat /sys/devices/system/cpu/cpufreq/policy*/scaling_max_freq | uniq
2151
$ cat /sys/devices/system/cpu/cpufreq/policy*/cpuinfo_min_freq | uniq
400000
$ cat /sys/devices/system/cpu/cpufreq/policy*/scaling_cur_freq | uniq
2151
409422
After:
$ cat /sys/devices/system/cpu/cpufreq/policy*/scaling_max_freq | uniq
2151000
$ cat /sys/devices/system/cpu/cpufreq/policy*/cpuinfo_min_freq | uniq
400000
$ cat /sys/devices/system/cpu/cpufreq/policy*/scaling_cur_freq | uniq
2151000
1799527
Fixes: ec437d71db ("cpufreq: amd-pstate: Introduce a new AMD P-State driver to support future processors")
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Acked-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Tested-by: Peter Jung <ptr1337@cachyos.org>
Cc: 5.17+ <stable@vger.kernel.org> # 5.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When extra warnings are enabled, gcc points out a global variable
definition in a header:
In file included from drivers/cpufreq/amd-pstate-ut.c:29:
include/linux/amd-pstate.h:123:27: error: 'amd_pstate_mode_string' defined but not used [-Werror=unused-const-variable=]
123 | static const char * const amd_pstate_mode_string[] = {
| ^~~~~~~~~~~~~~~~~~~~~~
This header is only included from two files in the same directory,
and one of them uses only a single definition from it, so clean it
up by moving most of the contents into the driver that uses them,
and making shared bits a local header file.
Fixes: 36c5014e54 ("cpufreq: amd-pstate: optimize driver working mode selection in amd_pstate_param()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The patch updates the function documentation comment for
longhaul_setstate to adhere to the kernel-doc specification.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Make use of the __free() macro to automate memory deallocation when
the existing device nodes get out of scope, removing the need for
of_node_put() and therefore increasing code safety if more error paths
are added to the driver, which could miss the required of_node_put()
as it already occurred with commit '57f2f8b4aa0c ("cpufreq: qcom:
Refactor the driver to make it easier to extend")'.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The code refactoring added new error paths between the np device node
allocation and the call to of_node_put(), which leads to memory leaks if
any of those errors occur.
Add the missing of_node_put() in the error paths that require it.
Cc: stable@vger.kernel.org
Fixes: 57f2f8b4aa ("cpufreq: qcom: Refactor the driver to make it easier to extend")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Conversion of target_freq to HZ in scmi_cpufreq_fast_switch()
can lead to overflow if the multiplied result is greater than
UINT_MAX, since type of target_freq is unsigned int. Avoid this
overflow by assigning target_freq to unsigned long variable for
converting it to HZ.
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Make use of the __free() cleanup handler to automatically free nodes
when they get out of scope.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The for_each_child_of_node() loop does not decrement the child node
refcount before the break instruction, even though the node is no
longer required.
This can be avoided with the new for_each_child_of_node_scoped() macro
that removes the need for any of_node_put().
Fixes: fa5aec9561 ("cpufreq: sun50i: Add support for opp_supported_hw")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Like all other SoCs in IPQ5332 family, cpufreq for IPQ5321 is also
determined by the eFuse, with the maximum limit of 1.1GHz. Add support
for the same.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Signed-off-by: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
Link: https://lore.kernel.org/r/20240325-ipq5321-sku-support-v2-3-f30ce244732f@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
- Fix a memory leak in the exit path of amd-pstate (Peng Ma).
- Fix required_opp_tables handling in the cases when multiple generic
PM domains share one OPP table (Viresh Kumar).
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAmZMYk8SHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRxdUIP/31SNqWSNni7aiUirnMIg60UbpM3jTMm
apkqHaSqdpL4ExM/Y8caSL9rIQD3P1GhWHy+0JVuK5tNiFH84oyMmKYd0v01QVy/
DLDs55XpPAgbkEjCcloe3QaR8mWgnQIXatjQkVoXZu3LAH6QLnDzT5w7C4HFXFEL
4gVlBvM/S69pf6FBG0SZhKLON3zryGHCBQMqOFcowJ8QGnfQsC+YzEWwvyncsDv4
nFV/lje/LwARlsxUfjc7EZmf8tRtfgkgSFm+3pI/EtQikKwI0ttheF8eE4MEtpxe
0A3xCV1aDq+tQEXgU7IIqVvsuu5xOcdfJ3rfYm5GmgZSh1RU1b80S7MJPWBJn0ip
PTjVZ3UyaW+YhGw5br2uXWK427PRhPHUyfCPO1UiSSDu0qZPNNHIjv5RQk336Sbt
NQUl7XO45Lv5XwGq8uqCXxnxN8LaNiOd+JZ6xm3R34Pc/vR6zEptOc/748WS2cxV
O2h1F6u0MiFqP9ieTcY23anrZqU//a61P8xz9e6oRfieUylOExG/aAsNrZ9Q2J6Z
T9mMj9OQlcbXIu7X2Ai6Fn3ppWR8/rVJu2i2WwrsGYkdnWuJ3BqdMOpnKw1438bb
2AC2Pc0hC22p8/tpqckcwSHJOOYCynOc7y/2/X7skcY+jkXg5zhPtBCx3GhCsEjV
RUj9L2CTorvS
=mGfT
-----END PGP SIGNATURE-----
Merge tag 'pm-6.10-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix the amd-pstate driver and the operating performance point
(OPP) handling related to generic PM domains.
Specifics:
- Fix a memory leak in the exit path of amd-pstate (Peng Ma)
- Fix required_opp_tables handling in the cases when multiple generic
PM domains share one OPP table (Viresh Kumar)"
* tag 'pm-6.10-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
OPP: Fix required_opp_tables for multiple genpds using same table
cpufreq: amd-pstate: fix memory leak on CPU EPP exit
- Enable BPF Kernel Functions (kfuncs) in the powerpc BPF JIT.
- Allow per-process DEXCR (Dynamic Execution Control Register) settings via
prctl, notably NPHIE which controls hashst/hashchk for ROP protection.
- Install powerpc selftests in sub-directories. Note this changes the way
run_kselftest.sh needs to be invoked for powerpc selftests.
- Change fadump (Firmware Assisted Dump) to better handle memory add/remove.
- Add support for passing additional parameters to the fadump kernel.
- Add support for updating the kdump image on CPU/memory add/remove events.
- Other small features, cleanups and fixes.
Thanks to: Andrew Donnellan, Andy Shevchenko, Aneesh Kumar K.V, Arnd Bergmann,
Benjamin Gray, Bjorn Helgaas, Christian Zigotzky, Christophe Jaillet, Christophe
Leroy, Colin Ian King, Cédric Le Goater, Dr. David Alan Gilbert, Erhard Furtner,
Frank Li, GUO Zihua, Ganesh Goudar, Geoff Levand, Ghanshyam Agrawal, Greg Kurz,
Hari Bathini, Joel Stanley, Justin Stitt, Kunwu Chan, Li Yang, Lidong Zhong,
Madhavan Srinivasan, Mahesh Salgaonkar, Masahiro Yamada, Matthias Schiffer,
Naresh Kamboju, Nathan Chancellor, Nathan Lynch, Naveen N Rao, Nicholas
Miehlbradt, Ran Wang, Randy Dunlap, Ritesh Harjani, Sachin Sant, Shirisha Ganta,
Shrikanth Hegde, Sourabh Jain, Stephen Rothwell, sundar, Thorsten Blum, Vaibhav
Jain, Xiaowei Bao, Yang Li, Zhao Chenhui.
-----BEGIN PGP SIGNATURE-----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=GoCV
-----END PGP SIGNATURE-----
Merge tag 'powerpc-6.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Enable BPF Kernel Functions (kfuncs) in the powerpc BPF JIT.
- Allow per-process DEXCR (Dynamic Execution Control Register) settings
via prctl, notably NPHIE which controls hashst/hashchk for ROP
protection.
- Install powerpc selftests in sub-directories. Note this changes the
way run_kselftest.sh needs to be invoked for powerpc selftests.
- Change fadump (Firmware Assisted Dump) to better handle memory
add/remove.
- Add support for passing additional parameters to the fadump kernel.
- Add support for updating the kdump image on CPU/memory add/remove
events.
- Other small features, cleanups and fixes.
Thanks to Andrew Donnellan, Andy Shevchenko, Aneesh Kumar K.V, Arnd
Bergmann, Benjamin Gray, Bjorn Helgaas, Christian Zigotzky, Christophe
Jaillet, Christophe Leroy, Colin Ian King, Cédric Le Goater, Dr. David
Alan Gilbert, Erhard Furtner, Frank Li, GUO Zihua, Ganesh Goudar, Geoff
Levand, Ghanshyam Agrawal, Greg Kurz, Hari Bathini, Joel Stanley, Justin
Stitt, Kunwu Chan, Li Yang, Lidong Zhong, Madhavan Srinivasan, Mahesh
Salgaonkar, Masahiro Yamada, Matthias Schiffer, Naresh Kamboju, Nathan
Chancellor, Nathan Lynch, Naveen N Rao, Nicholas Miehlbradt, Ran Wang,
Randy Dunlap, Ritesh Harjani, Sachin Sant, Shirisha Ganta, Shrikanth
Hegde, Sourabh Jain, Stephen Rothwell, sundar, Thorsten Blum, Vaibhav
Jain, Xiaowei Bao, Yang Li, and Zhao Chenhui.
* tag 'powerpc-6.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (85 commits)
powerpc/fadump: Fix section mismatch warning
powerpc/85xx: fix compile error without CONFIG_CRASH_DUMP
powerpc/fadump: update documentation about bootargs_append
powerpc/fadump: pass additional parameters when fadump is active
powerpc/fadump: setup additional parameters for dump capture kernel
powerpc/pseries/fadump: add support for multiple boot memory regions
selftests/powerpc/dexcr: Fix spelling mistake "predicition" -> "prediction"
KVM: PPC: Book3S HV nestedv2: Fix an error handling path in gs_msg_ops_kvmhv_nestedv2_config_fill_info()
KVM: PPC: Fix documentation for ppc mmu caps
KVM: PPC: code cleanup for kvmppc_book3s_irqprio_deliver
KVM: PPC: Book3S HV nestedv2: Cancel pending DEC exception
powerpc/xmon: Check cpu id in commands "c#", "dp#" and "dx#"
powerpc/code-patching: Use dedicated memory routines for patching
powerpc/code-patching: Test patch_instructions() during boot
powerpc64/kasan: Pass virtual addresses to kasan_init_phys_region()
powerpc: rename SPRN_HID2 define to SPRN_HID2_750FX
powerpc: Fix typos
powerpc/eeh: Fix spelling of the word "auxillary" and update comment
macintosh/ams: Fix unused variable warning
powerpc/Makefile: Remove bits related to the previous use of -mcmodel=large
...
The cpudata memory from kzalloc() in amd_pstate_epp_cpu_init() is
not freed in the analogous exit function, so fix that.
Signed-off-by: Peng Ma <andypma@tencent.com>
Acked-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Perry Yuan <Perry.Yuan@amd.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Rework the handling of disabled turbo in the intel_pstate driver and
make it update the maximum CPU frequency consistently regardless of
the reason on top of a number of cleanups (Rafael Wysocki).
- Add missing checks for NULL .exit() cpufreq driver callback to the
cpufreq core (Viresh Kumar).
- Prevent pulicy->max from going above the frequency QoS maximum value
when cpufreq_frequency_table_verify() is used (Xuewen Yan).
- Prevent a negative CPU number or frequency value from being printed
if they are really large (Joshua Yeong).
- Update MAINTAINERS entry for amd-pstate to add two new submaintainers
and a designated reviewer (Huang Rui).
- Clean up the amd-pstate driver and update its documentation (Gautham
Shenoy).
- Fix the highest frequency issue in the amd-pstate driver which limits
performance (Perry Yuan).
- Enable CPPC v2 for certain processors in the family 17H, as requested
by TR40 processor users who expect improved performance and lower
system temperature (Perry Yuan).
- Change latency and delay values to be read from platform firmware
firstly for more accurate timing (Perry Yuan).
- A new quirk is introduced for supporting amd-pstate on legacy
processors which either lack CPPC capability, or only only have CPPC
v2 capability (Perry Yuan).
- Sun50i cpufreq: Add support for opp_supported_hw, H616 platform and
general cleanups (Andre Przywara, Martin Botka, Brandon Cheo Fusi,
Dan Carpenter, Viresh Kumar).
- CPPC cpufreq: Fix possible null pointer dereference (Aleksandr
Mishin).
- Eliminate uses of of_node_put() from cpufreq (Javier Carrasco,
Shivani Gupta).
- brcmstb-avs: ISO C90 forbids mixed declarations (Portia Stephens).
- mediatek cpufreq: Add support for MT7988A (Sam Shih).
- cpufreq-qcom-hw: Add SM4450 compatibles in DT bindings (Tengfei Fan).
- Fix struct cpudata::epp_cached kernel-doc in the intel_pstate cpufreq
driver (Jeff Johnson).
- Fix kerneldoc description of ladder_do_selection() (Jeff Johnson).
- Convert the cpuidle kirkwood driver to platform remove callback
returning void (Yangtao Li).
- Replace deprecated strncpy() with strscpy() in the hibernation core
code (Justin Stitt).
- Use %ps to simplify debug output in the core system-wide suspend and
resume code (Len Brown).
- Remove unnecessary else from device_init_wakeup() and make
device_wakeup_disable() return void (Dhruva Gole).
- Enable PMU support in the Intel TPMI RAPL driver (Zhang Rui).
- Add support for ArrowLake-H platform to the Intel RAPL driver (Zhang
Rui).
- Avoid explicit cpumask allocation on stack in DTPM (Dawei Li).
- Make the Samsung exynos-asv driver update the Energy Model after
adjusting voltage on top of some preliminary changes of the OPP and
Enery Model generic code (Lukasz Luba).
- Remove a reference to a function that has been dropped from the power
management documentation (Bjorn Helgaas).
- Convert the platfrom remove callback to .remove_new for the
exyno-nocp, exynos-ppmu, mtk-cci-devfreq, sun8i-a33-mbus, and
rk3399_dmc devfreq drivers (Uwe Kleine-König).
- Use DEFINE_SIMPLE_PM_OPS for exyno-bus.c driver (Anand Moon).
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAmZCZrASHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRxH3cP/RwYN6V3H+XUlhxN0M1GXb8zkLGTLm9X
mGRKzDAoElGwYJVSpGPPtP0F+IaS3Sb7JnB719lSS7u7LmYIcqivTaBRdDIHWILJ
qWbTSy7+84Zakf0RZ5qRr3GIGcNHmY5QDZf3/jC0AX4VBnFqFCjpaW04zmUjmAqn
k13V3vfHl0J2/qKkm/JIvg2hubcAQzcP9UMgsjRE/S9QzNScEe7910v+0pv8XyUW
4kdjSItUG8CaJV5er/XarYl4bh39OqT8Lvuo4wbaCFvOyRsMHoXqStxZVLTb9iEI
j96vBXdy5Bfs503vc+Bu3TGcKPQTfjeRkEYDlwvpxwtJfMGnRQemgidSQwsbz208
oQaybFxU0UHMgsVh1R0VrbdrhUuMxUz1OrCPSg6rhYJTZ1UhTwISoDTdf+SstGCC
ODZgG59m6ez5udFAeavLA319jQEGL/oWPkHckVld4Gr10qrMu7SWseflx/+RY2dG
Rjvd/Kv9FYWVyrIttQf3YIFlc3SLhM5K4IxPhzvj94MDs4spbwAx3wk5lR1Nw2ct
HIVVjfBS+9I5dlRI7+VLM7VzD1JUxOOeZH84aTMDL080hiFZLEJaD+TkCc2QCa02
5fGSa1DM5wX87TCdltRtW+OP715Q+97OXdeRQtwgIewfM8zPi0m2ctODNj08+EO1
qmlFSJYTmFhR
=el5Y
-----END PGP SIGNATURE-----
Merge tag 'pm-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These are mostly cpufreq updates, including a significant intel-pstate
driver update and several amd-pstate improvements plus some updates of
ARM cpufreq drivers, general fixes and cleanups.
Also included are changes related to system sleep, power capping
updates adding support for a new platform and a new hardware feature
(among other things), a Samsung exynos-asv driver update allowing it
to change its Energy Model after adjusting voltage, minor cpuidle and
devfreq updates and a small documentation cleanup.
Specifics:
- Rework the handling of disabled turbo in the intel_pstate driver
and make it update the maximum CPU frequency consistently
regardless of the reason on top of a number of cleanups (Rafael
Wysocki)
- Add missing checks for NULL .exit() cpufreq driver callback to the
cpufreq core (Viresh Kumar)
- Prevent pulicy->max from going above the frequency QoS maximum
value when cpufreq_frequency_table_verify() is used (Xuewen Yan)
- Prevent a negative CPU number or frequency value from being printed
if they are really large (Joshua Yeong)
- Update MAINTAINERS entry for amd-pstate to add two new
submaintainers and a designated reviewer (Huang Rui)
- Clean up the amd-pstate driver and update its documentation
(Gautham Shenoy)
- Fix the highest frequency issue in the amd-pstate driver which
limits performance (Perry Yuan)
- Enable CPPC v2 for certain processors in the family 17H, as
requested by TR40 processor users who expect improved performance
and lower system temperature (Perry Yuan)
- Change latency and delay values to be read from platform firmware
firstly for more accurate timing (Perry Yuan)
- A new quirk is introduced for supporting amd-pstate on legacy
processors which either lack CPPC capability, or only only have
CPPC v2 capability (Perry Yuan)
- Sun50i cpufreq: Add support for opp_supported_hw, H616 platform and
general cleanups (Andre Przywara, Martin Botka, Brandon Cheo Fusi,
Dan Carpenter, Viresh Kumar)
- CPPC cpufreq: Fix possible null pointer dereference (Aleksandr
Mishin)
- Eliminate uses of of_node_put() from cpufreq (Javier Carrasco,
Shivani Gupta)
- brcmstb-avs: ISO C90 forbids mixed declarations (Portia Stephens)
- mediatek cpufreq: Add support for MT7988A (Sam Shih)
- cpufreq-qcom-hw: Add SM4450 compatibles in DT bindings (Tengfei
Fan)
- Fix struct cpudata::epp_cached kernel-doc in the intel_pstate
cpufreq driver (Jeff Johnson)
- Fix kerneldoc description of ladder_do_selection() (Jeff Johnson)
- Convert the cpuidle kirkwood driver to platform remove callback
returning void (Yangtao Li)
- Replace deprecated strncpy() with strscpy() in the hibernation core
code (Justin Stitt)
- Use %ps to simplify debug output in the core system-wide suspend
and resume code (Len Brown)
- Remove unnecessary else from device_init_wakeup() and make
device_wakeup_disable() return void (Dhruva Gole)
- Enable PMU support in the Intel TPMI RAPL driver (Zhang Rui)
- Add support for ArrowLake-H platform to the Intel RAPL driver
(Zhang Rui)
- Avoid explicit cpumask allocation on stack in DTPM (Dawei Li)
- Make the Samsung exynos-asv driver update the Energy Model after
adjusting voltage on top of some preliminary changes of the OPP and
Enery Model generic code (Lukasz Luba)
- Remove a reference to a function that has been dropped from the
power management documentation (Bjorn Helgaas)
- Convert the platfrom remove callback to .remove_new for the
exyno-nocp, exynos-ppmu, mtk-cci-devfreq, sun8i-a33-mbus, and
rk3399_dmc devfreq drivers (Uwe Kleine-König)
- Use DEFINE_SIMPLE_PM_OPS for exyno-bus.c driver (Anand Moon)"
* tag 'pm-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (68 commits)
PM / devfreq: exynos: Use DEFINE_SIMPLE_DEV_PM_OPS for PM functions
PM / devfreq: rk3399_dmc: Convert to platform remove callback returning void
PM / devfreq: sun8i-a33-mbus: Convert to platform remove callback returning void
PM / devfreq: mtk-cci: Convert to platform remove callback returning void
PM / devfreq: exynos-ppmu: Convert to platform remove callback returning void
PM / devfreq: exynos-nocp: Convert to platform remove callback returning void
cpufreq: amd-pstate: fix the highest frequency issue which limits performance
cpufreq: intel_pstate: fix struct cpudata::epp_cached kernel-doc
cpuidle: ladder: fix ladder_do_selection() kernel-doc
powercap: intel_rapl_tpmi: Enable PMU support
powercap: intel_rapl: Introduce APIs for PMU support
PM: hibernate: replace deprecated strncpy() with strscpy()
cpufreq: Fix up printing large CPU numbers and frequency values
MAINTAINERS: cpufreq: amd-pstate: Add co-maintainers and reviewer
cpufreq: amd-pstate: remove unused variable lowest_nonlinear_freq
cpufreq: amd-pstate: fix code format problems
cpufreq: amd-pstate: Add quirk for the pstate CPPC capabilities missing
cppc_acpi: print error message if CPPC is unsupported
cpufreq: amd-pstate: get transition delay and latency value from ACPI tables
cpufreq: amd-pstate: Bail out if min/max/nominal_freq is 0
...
To address the performance drop issue, an optimization has been
implemented. The incorrect highest performance value previously set by the
low-level power firmware for AMD CPUs with Family ID 0x19 and Model ID
ranging from 0x70 to 0x7F series has been identified as the cause.
To resolve this, a check has been implemented to accurately determine the
CPU family and model ID. The correct highest performance value is now set
and the performance drop caused by the incorrect highest performance value
are eliminated.
Before the fix, the highest frequency was set to 4200MHz, now it is set
to 4971MHz which is correct.
CPU NODE SOCKET CORE L1d:L1i:L2:L3 ONLINE MAXMHZ MINMHZ MHZ
0 0 0 0 0:0:0:0 yes 4971.0000 400.0000 400.0000
1 0 0 0 0:0:0:0 yes 4971.0000 400.0000 400.0000
2 0 0 1 1:1:1:0 yes 4971.0000 400.0000 4865.8140
3 0 0 1 1:1:1:0 yes 4971.0000 400.0000 400.0000
Fixes: f3a0523918 ("cpufreq: amd-pstate: Enable amd-pstate preferred core support")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218759
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Co-developed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Tested-by: Gaha Bana <gahabana@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This register number is hardware-specific, rename it for clarity.
FIXME comments are added in a few places where it seems like the wrong
register is used. As I can't test this, only the rename is done with no
functional change.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240124105031.45734-1-matthias.schiffer@ew.tq-group.com
make C=1 currently gives the following warning:
drivers/cpufreq/intel_pstate.c:262: warning: Function parameter or struct member 'epp_cached' not described in 'cpudata'
Add the missing ":" to fix the trivial kernel-doc syntax error.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge AMD P-state driver changes from Perry Yuan for v6.10:
"- Enable CPPC v2 for certain processors in the family 17H, as requested
by TR40 processor users who expect improved performance and lower
system temperature.
- Change latency and delay values to be read from platform firmware
firstly for more accurate timing.
- A new quirk is introduced for supporting amd-pstate on legacy
processors which either lack CPPC capability, or only only have CPPC
v2 capability."
* amd-pstate:
MAINTAINERS: cpufreq: amd-pstate: Add co-maintainers and reviewer
cpufreq: amd-pstate: remove unused variable lowest_nonlinear_freq
cpufreq: amd-pstate: fix code format problems
cpufreq: amd-pstate: Add quirk for the pstate CPPC capabilities missing
cppc_acpi: print error message if CPPC is unsupported
cpufreq: amd-pstate: get transition delay and latency value from ACPI tables
cpufreq: amd-pstate: Bail out if min/max/nominal_freq is 0
cpufreq: amd-pstate: Remove amd_get_{min,max,nominal,lowest_nonlinear}_freq()
cpufreq: amd-pstate: Unify computation of {max,min,nominal,lowest_nonlinear}_freq
cpufreq: amd-pstate: Document the units for freq variables in amd_cpudata
cpufreq: amd-pstate: Document *_limit_* fields in struct amd_cpudata
A negative CPU number or frequency value may be printed if they are
really large (which is unlikely, though).
Signed-off-by: Joshua Yeong <joshua.yeong@starfivetech.com>
Reviewed-by: Thorsten Blum <thorsten.blum@toblux.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Subject and changelog edits. ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
removed the unused variable `lowest_nonlinear_freq` for build warning.
This variable was defined and assigned a value in the previous code,
but it was not used in the subsequent code.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202404271038.em6nJjzy-lkp@intel.com/
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
get some code format problems fixed in the amd-pstate driver.
Changes Made:
- Fixed incorrect comment format in the functions.
- Removed unnecessary blank line.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202404271148.HK9yHBlB-lkp@intel.com/
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add quirks table to get CPPC capabilities issue fixed by providing
correct perf or frequency values while driver loading.
If CPPC capabilities are not defined in the ACPI tables or wrongly
defined by platform firmware, it needs to use quick to get those
issues fixed with correct workaround values to make pstate driver
can be loaded even though there are CPPC capabilities errors.
The workaround will match the broken BIOS which lack of CPPC capabilities
nominal_freq and lowest_freq definition in the ACPI table.
$ cat /sys/devices/system/cpu/cpu0/acpi_cppc/lowest_freq
0
$ cat /sys/devices/system/cpu/cpu0/acpi_cppc/nominal_freq
0
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Tested-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make pstate driver initially retrieve the P-state transition delay and
latency values from the BIOS ACPI tables which has more reasonable
delay and latency values according to the platform design and
requirements.
Previously there values were hardcoded at specific value which may
have conflicted with platform and it might not reflect the most
accurate or optimized setting for the processor.
[054h 0084 8] Preserve Mask : FFFFFFFF00000000
[05Ch 0092 8] Write Mask : 0000000000000001
[064h 0100 4] Command Latency : 00000FA0
[068h 0104 4] Maximum Access Rate : 0000EA60
[06Ch 0108 2] Minimum Turnaround Time : 0000
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Tested-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The amd-pstate driver cannot work when the min_freq, nominal_freq or
the max_freq is zero. When this happens it is prudent to error out
early on rather than waiting failing at the time of the governor
initialization.
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Tested-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
amd_get_{min,max,nominal,lowest_nonlinear}_freq() functions merely
return cpudata->{min,max,nominal,lowest_nonlinear}_freq values.
There is no loss in readability in replacing their invocations by
accesses to the corresponding members of cpudata.
Do so and remove these helper functions.
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Li Meng <li.meng@amd.com>
Tested-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently the amd_get_{min, max, nominal, lowest_nonlinear}_freq()
helpers computes the values of min_freq, max_freq, nominal_freq and
lowest_nominal_freq respectively afresh from
cppc_get_perf_caps(). This is not necessary as there are fields in
cpudata to cache these values.
To simplify this, add a single helper function named
amd_pstate_init_freq() which computes all these frequencies at once, and
caches it in cpudata.
Use the cached values everywhere else in the code.
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Li Meng <li.meng@amd.com>
Tested-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Co-developed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The dt_has_supported_hw() function returns type bool. That means these
negative error codes are cast to true but the function should return
false instead.
Fixes: fa5aec9561 ("cpufreq: sun50i: Add support for opp_supported_hw")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
There is a compile warning because a NULL pointer check was added before
a struct was declared. This moves the NULL pointer check to after the
struct is declared and moves the struct assignment to after the NULL
pointer check.
Fixes: f661017e6d ("cpufreq: brcmstb-avs-cpufreq: add check for cpufreq_cpu_get's return value")
Signed-off-by: Portia Stephens <portia.stephens@canonical.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Now that cpufreq provides a pressure value to the scheduler, rename
arch_update_thermal_pressure into HW pressure to reflect that it returns
a pressure applied by HW (i.e. with a high frequency change) and not
always related to thermal mitigation but also generated by max current
limitation as an example. Such high frequency signal needs filtering to be
smoothed and provide an value that reflects the average available capacity
into the scheduler time scale.
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Qais Yousef <qyousef@layalina.io>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20240326091616.3696851-5-vincent.guittot@linaro.org
Provide to the scheduler a feedback about the temporary max available
capacity. Unlike arch_update_thermal_pressure(), this doesn't need to be
filtered as the pressure will happen for dozens of ms or more.
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Qais Yousef <qyousef@layalina.io>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20240326091616.3696851-2-vincent.guittot@linaro.org
Make use of the __free() cleanup handler to automatically free nodes
when they get out of scope.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Make use of the __free() cleanup handler to automatically free nodes
when they get out of scope.
Only find_supply_name() is affected, and the new mechanism removes the
need for a 'goto' and the 'name' local variable.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Modify the ti_cpufreq_match_node() function to utilize the __free()
cleanup handler for automatically releasing the device node when it goes
out of scope.
By moving the declaration to the initialization, the patch ensures that
the device node is properly managed throughout the function's scope,
thus eliminating the need for manual invocation of of_node_put().
This approach reduces the potential for memory leaks.
Suggested-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Shivani Gupta <shivani07g@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
This add cpufreq support for mediatek MT7988A SoC.
The platform data of MT7988A is different from previous MediaTek SoCs,
so we add a new compatible and platform data for it.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The Sun50i driver generates a warning with W=1:
warning: '%d' directive output may be truncated writing between 1 and 10 bytes into a region of size 2 [-Wformat-truncation=]
Fix it by allocating a big enough array to print an integer.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202404191715.LDwMm2gP-lkp@intel.com/
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
The Allwinner H616/H618 SoCs have different OPP tables per SoC version
and die revision. The SoC version is stored in NVMEM, as before, though
encoded differently. The die revision is in a different register, in the
SRAM controller. Firmware already exports that value in a standardised
way, through the SMCCC SoCID mechanism. We need both values, as some chips
have the same SoC version, but they don't support the same frequencies and
they get differentiated by the die revision.
Add the new compatible string and tie the new translation function to
it. This mechanism not only covers the original H616 SoC, but also its
very close sibling SoCs H618 and H700, so add them to the list as well.
Signed-off-by: Martin Botka <martin.botka@somainline.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The opp_supported_hw DT property allows the DT to specify a mask of chip
revisions that a certain OPP is eligible for. This allows for easy
limiting of maximum frequencies, for instance.
Add support for that in the sun50i-cpufreq-nvmem driver. We support both
the existing opp-microvolt suffix properties as well as the
opp-supported-hw property, the generic code figures out which is needed
automatically.
However if none of the DT OPP nodes contain an opp-supported-hw
property, the core code will ignore all OPPs and the driver will fail
probing. So check the DT's eligibility first before using that feature.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Make converting the speed bin value into a speed grade generic and
determined by a platform specific callback. Also change the prototypes
involved to encode the speed bin directly in the return value.
This allows to extend the driver more easily to support more SoCs.
Signed-off-by: Brandon Cheo Fusi <fusibrandon13@gmail.com>
[Andre: merge output into return value]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The AllWinner H616 SoC will use the (extended) H6 OPP driver, so add
them to the cpufreq-dt blocklist, to not create the device twice.
This also affects the closely related sibling SoCs H618 and H700.
Signed-off-by: Martin Botka <martin.botka@somainline.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
cppc_cpufreq_get_rate() and hisi_cppc_cpufreq_get_rate() can be called from
different places with various parameters. So cpufreq_cpu_get() can return
null as 'policy' in some circumstances.
Fix this bug by adding null return check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: a28b2bfc09 ("cppc_cpufreq: replace per-cpu data array with a list")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Make use of the __free() cleanup handler to automatically free nodes
when they get out of scope. Only the probe function is affected by this
modification.
Given that this mechanism requires the node to be initialized, its
initialization and the value check have been moved to the top of the
function.
After removing uses of of_node_put(), the jump to out_put_np is no
longer necessary.
Suggested-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The exit() callback is optional and shouldn't be called without checking
a valid pointer first.
Also, we must clear freq_table pointer even if the exit() callback isn't
present.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Fixes: 91a12e91dc ("cpufreq: Allow light-weight tear down and bring up of CPUs")
Fixes: f339f35417 ("cpufreq: Rearrange locking in cpufreq_remove_dev()")
Reported-by: Lizhe <sensor1010@163.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The reference to this variable is hidden in an #ifdef:
drivers/cpufreq/intel_pstate.c:2440:32: error: 'intel_pstate_cpu_oob_ids' defined but not used [-Werror=unused-const-variable=]
Use the same check around the definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are 3 places at which the maximum CPU frequency may change,
store_no_turbo(), intel_pstate_update_limits() (when called by the
cpufreq core) and intel_pstate_notify_work() (when handling a HWP
change notification). Currently, cpuinfo.max_freq is only updated by
store_no_turbo() and intel_pstate_notify_work(), although it principle
it may be necessary to update it in intel_pstate_update_limits() either.
Make all of them mutually consistent.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Replace the global.turbo_disabled in __intel_pstate_update_max_freq() with
a global.no_turbo one to make store_no_turbo() actually update the maximum
CPU frequency on the trubo preference changes, which needs to be consistent
with arch_set_max_freq_ratio() called from there.
For more consistency, replace the global.turbo_disabled checks in
__intel_pstate_cpu_init() and intel_cpufreq_adjust_perf() with
global.no_turbo checks either.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Because global.no_turbo is generally not read under intel_pstate_driver_lock
make store_no_turbo() use WRITE_ONCE() for updating it (this is the only
place at which it is updated except for the initialization) and make the
majority of places reading it use READ_ONCE().
Also remove redundant global.turbo_disabled checks from places that
depend on the 'true' value of global.no_turbo because it can only be
'true' if global.turbo_disabled is also 'true'.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Now that global.turbo_disabled can only change at the cpufreq driver
registration time, initialize global.no_turbo at that time too so they
are in sync to start with (if the former is set, the latter cannot be
updated later anyway).
That allows show_no_turbo() to be simlified because it does not need
to check global.turbo_disabled and store_no_turbo() can be rearranged
to avoid doing anything if the new value of global.no_turbo is equal
to the current one and only return an error on attempts to clear
global.no_turbo when global.turbo_disabled.
While at it, eliminate the redundant ret variable from store_no_turbo().
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
The global.turbo_disabled is updated quite often, especially in the
passive mode in which case it is updated every time the scheduler calls
into the driver. However, this is generally not necessary and it adds
MSR read overhead to scheduler code paths (and that particular MSR is
slow to read).
For this reason, make the driver read MSR_IA32_MISC_ENABLE_TURBO_DISABLE
just once at the cpufreq driver registration time and remove all of the
in-flight updates of global.turbo_disabled.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Fold intel_pstate_max_within_limits() into its only caller.
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
There are at least 3 variables in intel_pstate that do not get updated
after they have been initialized, so annotate them with __ro_after_init.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Drop two redundant checks involving READ_ONCE() from notify_hwp_interrupt()
and make it check hwp_active without READ_ONCE() which is not necessary,
because that variable is only set once during the early initialization of
the driver.
In order to make that clear, annotate hwp_active with __ro_after_init.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make intel_pstate_disable_hwp_interrupt() wait for canceled delayed work
to complete to avoid leftover work items running when it returns which
may be during driver unregistration and may confuse things going forward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Because intel_pstate_enable/disable_hwp_interrupt() are only called from
thread context, they need not save the IRQ flags when using a spinlock
as interrupts are guaranteed to be enabled when they run, so make them
use spin_lock/unlock_irq().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove the spinlock locking from intel_pstate_driver_cleanup() as it is
not necessary because no other code accessing all_cpu_data[] can run in
parallel with that function.
Had the locking been necessary, though, it would have been incorrect
because the lock in question is acquired from a hardirq handler and
it cannot be acquired from thread context without disabling interrupts.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When driver use the cpufreq_frequency_table_verify() as the
cpufreq_driver->verify's callback. It may cause the policy->max
bigger than the freq_qos's max freq.
Just as follow:
unisoc:/sys/devices/system/cpu/cpufreq/policy0 # cat scaling_available_frequencies
614400 768000 988000 1228800 1469000 1586000 1690000 1833000 2002000 2093000
unisoc:/sys/devices/system/cpu/cpufreq/policy0 # echo 1900000 > scaling_max_freq
unisoc:/sys/devices/system/cpu/cpufreq/policy0 # echo 1900000 > scaling_min_freq
unisoc:/sys/devices/system/cpu/cpufreq/policy0 # cat scaling_max_freq
2002000
unisoc:/sys/devices/system/cpu/cpufreq/policy0 # cat scaling_min_freq
2002000
When user set the qos_min and qos_max as the same value, and the value
is not in the freq-table, the above scenario will occur.
This is because in cpufreq_frequency_table_verify() func, when it can not
find the freq in table, it will change the policy->max to be a bigger freq,
as above, because there is no 1.9G in the freq-table, the policy->max would
be set to 2.002G. As a result, the cpufreq_policy->max is bigger than the
user's qos_max. This is unreasonable.
So use a smaller freq when can not find the freq in fre-table, to prevent
the policy->max exceed the qos's max freq.
Signed-off-by: Xuewen Yan <xuewen.yan@unisoc.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* Support for various vector-accelerated crypto routines.
* Hibernation is now enabled for portable kernel builds.
* mmap_rnd_bits_max is larger on systems with larger VAs.
* Support for fast GUP.
* Support for membarrier-based instruction cache synchronization.
* Support for the Andes hart-level interrupt controller and PMU.
* Some cleanups around unaligned access speed probing and Kconfig
settings.
* Support for ACPI LPI and CPPC.
* Various cleanus related to barriers.
* A handful of fixes.
-----BEGIN PGP SIGNATURE-----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=3dL5
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-6.9-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
- Support for various vector-accelerated crypto routines
- Hibernation is now enabled for portable kernel builds
- mmap_rnd_bits_max is larger on systems with larger VAs
- Support for fast GUP
- Support for membarrier-based instruction cache synchronization
- Support for the Andes hart-level interrupt controller and PMU
- Some cleanups around unaligned access speed probing and Kconfig
settings
- Support for ACPI LPI and CPPC
- Various cleanus related to barriers
- A handful of fixes
* tag 'riscv-for-linus-6.9-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (66 commits)
riscv: Fix syscall wrapper for >word-size arguments
crypto: riscv - add vector crypto accelerated AES-CBC-CTS
crypto: riscv - parallelize AES-CBC decryption
riscv: Only flush the mm icache when setting an exec pte
riscv: Use kcalloc() instead of kzalloc()
riscv/barrier: Add missing space after ','
riscv/barrier: Consolidate fence definitions
riscv/barrier: Define RISCV_FULL_BARRIER
riscv/barrier: Define __{mb,rmb,wmb}
RISC-V: defconfig: Enable CONFIG_ACPI_CPPC_CPUFREQ
cpufreq: Move CPPC configs to common Kconfig and add RISC-V
ACPI: RISC-V: Add CPPC driver
ACPI: Enable ACPI_PROCESSOR for RISC-V
ACPI: RISC-V: Add LPI driver
cpuidle: RISC-V: Move few functions to arch/riscv
riscv: Introduce set_compat_task() in asm/compat.h
riscv: Introduce is_compat_thread() into compat.h
riscv: add compile-time test into is_compat_task()
riscv: Replace direct thread flag check with is_compat_task()
riscv: Improve arch_get_mmap_end() macro
...
CPPC related config options are currently defined only in ARM specific
file. However, they are required for RISC-V as well. Instead of creating
a new Kconfig.riscv file and duplicating them, move them to the common
Kconfig file and enable RISC-V too.
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Pierre Gondois <pierre.gondois@arm.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20240208034414.22579-3-sunilvl@ventanamicro.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
- zero initialize a cpumask (Marek Szyprowski).
- Boost support for scmi cpufreq driver (Sibi Sankar).
-----BEGIN PGP SIGNATURE-----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=miRv
-----END PGP SIGNATURE-----
Merge tag 'cpufreq-arm-updates-6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Merge more ARM cpufreq updates for 6.9 from Viresh Kumar:
"- zero initialize a cpumask (Marek Szyprowski).
- Boost support for scmi cpufreq driver (Sibi Sankar)."
* tag 'cpufreq-arm-updates-6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: scmi: Enable boost support
firmware: arm_scmi: Add support for marking certain frequencies as turbo
cpufreq: dt: always allocate zeroed cpumask
Certain platforms host a number of higher OPPs that are exclusive to
CPUs within specific CPUfreq policies and not all CPUs within that
CPUfreq policy are able to achieve those higher OPPs due to power
constraints. These OPPs are marked as turbo in the freq_table and in
the presence of such OPPs, let's enable boost by default.
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Commit 0499a78369 ("ARM64: Dynamically allocate cpumasks and increase
supported CPUs to 512") changed the handling of cpumasks on ARM 64bit,
what resulted in the strange issues and warnings during cpufreq-dt
initialization on some big.LITTLE platforms.
This was caused by mixing OPPs between big and LITTLE cores, because
OPP-sharing information between big and LITTLE cores is computed on
cpumask, which in turn was not zeroed on allocation. Fix this by
switching to zalloc_cpumask_var() call.
Fixes: dc279ac6e5 ("cpufreq: dt: Refactor initialization to handle probe deferral properly")
CC: stable@vger.kernel.org # v5.10+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Christoph Lameter (Ampere) <cl@linux.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
In the existing code, per-policy flags don't have any impact i.e.
if cpufreq_driver boost is enabled and boost is disabled for one or
more of the policies, the cpufreq driver will behave as if boost is
enabled.
Fix this by incorporating per-policy boost flag in the policy->max
computation used in cpufreq_frequency_table_cpuinfo and setting the
default per-policy boost to mirror the cpufreq_driver boost flag.
Fixes: 218a06a79d ("cpufreq: Support per-policy performance boost")
Reported-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Tested-by:Yipeng Zou <zouyipeng@huawei.com> <mailto:zouyipeng@huawei.com>
Reviewed-by: Yipeng Zou <zouyipeng@huawei.com> <mailto:zouyipeng@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- General enhancements / cleanups to cpufreq drivers (tianyu2, Nícolas
F. R. A. Prado, Erick Archer, Arnd Bergmann, Anastasia Belova).
- Update cpufreq-dt-platdev to block/approve devices (Richard Acayan).
- scmi: get transition delay from firmware (Pierre Gondois).
-----BEGIN PGP SIGNATURE-----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=Hu43
-----END PGP SIGNATURE-----
Merge tag 'cpufreq-arm-updates-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Merge ARM cpufreq updates for 6.9 from Viresh Kumar:
"- General enhancements / cleanups to cpufreq drivers (tianyu2, Nícolas
F. R. A. Prado, Erick Archer, Arnd Bergmann, Anastasia Belova).
- Update cpufreq-dt-platdev to block/approve devices (Richard Acayan).
- scmi: get transition delay from firmware (Pierre Gondois)."
* tag 'cpufreq-arm-updates-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: scmi: Set transition_delay_us
firmware: arm_scmi: Populate fast channel rate_limit
firmware: arm_scmi: Populate perf commands rate_limit
cpufreq: qcom-hw: add CONFIG_COMMON_CLK dependency
cpufreq: dt-platdev: block SDM670 in cpufreq-dt-platdev
cpufreq: mediatek-hw: Don't error out if supply is not found
Documentation: power: Use kcalloc() instead of kzalloc()
cpufreq: mediatek-hw: Wait for CPU supplies before probing
cpufreq: brcmstb-avs-cpufreq: add check for cpufreq_cpu_get's return value
cpufreq: imx6: use regmap to read ocotp register
Make use of the newly added callbacks:
- rate_limit_get()
- fast_switch_rate_limit()
to populate policies's `transition_delay_us`, defined as the
'Preferred average time interval between consecutive
invocations of the driver to set the frequency for this policy.'
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Offlining a CPU and bringing it back online is a common operation and it
happens frequently during system suspend/resume, where the non-boot CPUs
are hotplugged out during suspend and brought back at resume.
The cpufreq core already tries to make this path as fast as possible as
the changes are only temporary in nature and full cleanup of resources
isn't required in this case. For example the drivers can implement
online()/offline() callbacks to avoid a lot of tear down of resources.
On similar lines, there is no need to unregister the cpufreq cooling
device during suspend / resume, but only while the policy is getting
removed.
Moreover, unregistering the cpufreq cooling device is resulting in an
unwanted outcome, where the system suspend is eventually aborted in the
process. Currently, during system suspend the cpufreq core unregisters
the cooling device, which in turn removes a kobject using device_del()
and that generates a notification to the userspace via uevent broadcast.
This causes system suspend to abort in some setups.
This was also earlier reported (indirectly) by Roman [1]. Maybe there is
another way around to fixing that problem properly, but this change
makes sense anyways.
Move the registering and unregistering of the cooling device to policy
creation and removal times onlyy.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218521
Reported-by: Manaf Meethalavalappu Pallikunhi <quic_manafm@quicinc.com>
Reported-by: Roman Stratiienko <r.stratiienko@gmail.com>
Link: https://patchwork.kernel.org/project/linux-pm/patch/20220710164026.541466-1-r.stratiienko@gmail.com/ [1]
Tested-by: Manaf Meethalavalappu Pallikunhi <quic_manafm@quicinc.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some platforms like Arm's Juno can have a high transition latency that
can be larger than the 2ms cap introduced. If a driver reports
a transition_latency that is higher than the cap, then use it as-is.
Update comment s/10/2/ to reflect the new cap of 2ms.
Reported-by: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Qais Yousef <qyousef@layalina.io>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The min/max limit perf values calculated based on frequency
may exceed the reasonable range of perf(highest perf, lowest perf).
Signed-off-by: Meng Li <li.meng@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A minimum sampling rate value of 10ms was introduced in:
commit cef9615a85 ("[CPUFREQ] ondemand: Uncouple minimal sampling rate from HZ in NO_HZ case")
The use of this value was removed in:
commit ed4676e254 ("cpufreq: Replace "max_transition_latency" with "dynamic_switching"")
Remove:
- a comment referencing this value
- an unused macro associated to this value
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Update default balanced_performance EPP to 115 and performance EPP to 16.
Changing the balanced_performance EPP has better performance/watt
compared to default powerup EPP value of 128.
Changing the performance EPP to 0x10 shows reduced power for similar
performance as EPP 0. On small form factor devices this is beneficial
as lower power results in lower CPU and skin temperature. This
results in reduced thermal throttling and higher performance.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The current implementation allows model specific EPP override for
balanced_performance. Add feature to allow model specific EPP for all
predefined EPP strings. For example for some CPU models, even changing
performance EPP has benefits
Use a mask of EPPs as driver_data instead of just balanced_performance.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is a loophole in pstate limit clamping for the intel_cpufreq CPU
frequency scaling driver (intel_pstate in passive mode), schedutil CPU
frequency scaling governor, HWP (HardWare Pstate) control enabled, when
the adjust_perf call back path is used.
Fix it.
Fixes: a365ab6b9d cpufreq: intel_pstate: Implement the ->adjust_perf() callback
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is still possible to compile-test a kernel without CONFIG_COMMON_CLK
for some ancient ARM boards or other architectures, but this causes a
link failure in the qcom-cpufreq-hw driver:
ERROR: modpost: "devm_clk_hw_register" [drivers/cpufreq/qcom-cpufreq-hw.ko] undefined!
ERROR: modpost: "devm_of_clk_add_hw_provider" [drivers/cpufreq/qcom-cpufreq-hw.ko] undefined!
ERROR: modpost: "of_clk_hw_onecell_get" [drivers/cpufreq/qcom-cpufreq-hw.ko] undefined!
Add a Kconfig dependency here to make sure this always work. Apparently
this bug has been in the kernel for a while without me running into it
on randconfig builds as COMMON_CLK is almost always enabled.
I have cross-checked by building an allmodconfig kernel with COMMON_CLK
disabled, which showed no other driver having this problem.
Fixes: 4370232c72 ("cpufreq: qcom-hw: Add CPU clock provider support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The Snapdragon 670 uses the Qualcomm driver for CPU frequency scaling.
Block this driver from loading on it so the driver does not pollute
dmesg with an error.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Commit 09c448d3c6 ("cpufreq: intel_pstate: Use IOWAIT flag in Atom
algorithm") removed the last user of cpudata::prev_cummulative_iowait.
Remove the member too.
Found by https://github.com/jirislaby/clang-struct.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
10ms is too high for today's hardware, even low end ones. This default
end up being used a lot on Arm machines at least. Pine64, mac mini and
pixel 6 all end up with 10ms rate_limit_us when using schedutil, and
it's too high for all of them.
Change the default to 2ms which should be 'pessimistic' enough for worst
case scenario, but not too high for platforms with fast DVFS hardware.
Signed-off-by: Qais Yousef <qyousef@layalina.io>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the function amd_pstate_adjust_perf(), the 'min_perf' variable is set
to 'highest_perf' instead of 'lowest_perf'.
Fixes: 1d215f0319 ("cpufreq: amd-pstate: Add fast switch function for AMD P-State")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reviewed-by: Perry Yuan <Perry.Yuan@amd.com>
Signed-off-by: Tor Vic <torvic9@mailbox.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: 6.1+ <stable@vger.kernel.org> # 6.1+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Preferred core rankings can be changed dynamically by the
platform based on the workload and platform conditions and
accounting for thermals and aging.
When this occurs, cpu priority need to be set.
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Wyes Karny <wyes.karny@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Perry Yuan <perry.yuan@amd.com>
Signed-off-by: Meng Li <li.meng@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
amd-pstate driver utilizes the functions and data structures
provided by the ITMT architecture to enable the scheduler to
favor scheduling on cores which can be get a higher frequency
with lower voltage. We call it amd-pstate preferrred core.
Here sched_set_itmt_core_prio() is called to set priorities and
sched_set_itmt_support() is called to enable ITMT feature.
amd-pstate driver uses the highest performance value to indicate
the priority of CPU. The higher value has a higher priority.
The initial core rankings are set up by amd-pstate when the
system boots.
Add a variable hw_prefcore in cpudata structure. It will check
if the processor and power firmware support preferred core
feature.
Add one new early parameter `disable` to allow user to disable
the preferred core.
Only when hardware supports preferred core and user set `enabled`
in early parameter, amd pstate driver supports preferred core featue.
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Wyes Karny <wyes.karny@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Co-developed-by: Perry Yuan <Perry.Yuan@amd.com>
Signed-off-by: Perry Yuan <Perry.Yuan@amd.com>
Signed-off-by: Meng Li <li.meng@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
devm_regulator_get_optional() returns -ENODEV if no supply can be found.
By introducing its usage, commit 788715b5f2 ("cpufreq: mediatek-hw:
Wait for CPU supplies before probing") caused the driver to fail probe
if no supply was present in any of the CPU DT nodes.
Use devm_regulator_get() instead since the CPUs do require supplies
even if not described in the DT. It will gracefully return a dummy
regulator if none is found in the DT node, allowing probe to succeed.
Fixes: 788715b5f2 ("cpufreq: mediatek-hw: Wait for CPU supplies before probing")
Reported-by: kernelci.org bot <bot@kernelci.org>
Closes: https://linux.kernelci.org/test/case/id/65b0b169710edea22852a3fa/
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Before proceeding with the probe and enabling frequency scaling for the
CPUs, make sure that all supplies feeding the CPUs have probed.
This fixes an issue observed on MT8195-Tomato where if the
mediatek-cpufreq-hw driver enabled the hardware (by writing to
REG_FREQ_ENABLE) before the SPMI controller driver (spmi-mtk-pmif),
behind which lies the big CPU supply, probed the platform would hang
shortly after with "rcu: INFO: rcu_preempt detected stalls on
CPUs/tasks" being printed in the log.
Fixes: 4855e26bcf ("cpufreq: mediatek-hw: Add support for CPUFREQ HW")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
cpufreq_cpu_get may return NULL. To avoid NULL-dereference check it
and return 0 in case of error.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: de322e0859 ("cpufreq: brcmstb-avs-cpufreq: AVS CPUfreq driver for Broadcom STB SoCs")
Signed-off-by: Anastasia Belova <abelova@astralinux.ru>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reading the ocotp register directly is unsafe and will cause the system
to hang if its clock is not turned on in CCM. The regmap interface has
clk enabled, which can solve this problem.
Signed-off-by: tianyu2 <tianyu2@kernelsoft.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Scaling min/max freq values were being cached and lagging a setting
each time. Fix the ordering of the clamp call to ensure they work.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217931
Fixes: febab20cae ("cpufreq/amd-pstate: Fix scaling_min_freq and scaling_max_freq update")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Wyes Karny <wkarny@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On systems using HWP, if a given frequency is equal to the maximum turbo
frequency or the maximum non-turbo frequency, the HWP performance level
corresponding to it is already known and can be used directly without
any computation.
Accordingly, adjust the code to use the known HWP performance levels in
the cases mentioned above.
This also helps to avoid limiting CPU capacity artificially in some
cases when the BIOS produces the HWP_CAP numbers using a different
E-core-to-P-core performance scaling factor than expected by the kernel.
Fixes: f5c8cf2a49 ("cpufreq: intel_pstate: hybrid: Use known scaling factor for P-cores")
Cc: 6.1+ <stable@vger.kernel.org> # 6.1+
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On some Meteor Lake platforms, maximum one core turbo frequency is not
observed. During hybrid performance to frequency conversion, the maximum
frequency is 100 MHz less. This results in requesting maximum frequency
100 MHz less.
For example when the max one core turbo is 4.9 GHz:
MSR HWP_CAPABILITIES shows highest performance ratio for P-core is 0x3E.
With the current scaling factor of 78741 (1.27x for converting frequency
to performance) results in max frequency of 4.8 GHz. This results in
capping the max scaling frequency as 4.8 GHz, which is 100 MHz less than
the desired.
Add capability to define per CPU model specific scaling factor and define
scaling factor of 80000 (1.25x for converting frequency to performance for
P-cores) for Meteor Lake.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Debug message adjustment, subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Add support for the Sierra Forest, Grand Ridge and Meteorlake SoCs to
the intel_idle cpuidle driver (Artem Bityutskiy, Zhang Rui).
- Do not enable interrupts when entering idle in the haltpoll cpuidle
driver (Borislav Petkov).
- Add Emerald Rapids support in no-HWP mode to the intel_pstate cpufreq
driver (Zhenguo Yao).
- Use EPP values programmed by the platform firmware as balanced
performance ones by default in intel_pstate (Srinivas Pandruvada).
- Add a missing function return value check to the SCMI cpufreq driver
to avoid unexpected behavior (Alexandra Diupina).
- Fix parameter type warning in the armada-8k cpufreq driver (Gregory
CLEMENT).
- Rework trans_stat_show() in the devfreq core code to avoid buffer
overflows (Christian Marangi).
- Synchronize devfreq_monitor_[start/stop] so as to prevent a timer
list corruption from occurring when devfreq governors are switched
frequently (Mukesh Ojha).
- Fix possible deadlocks in the core system-wide PM code that occur if
device-handling functions cannot be executed asynchronously during
resume from system-wide suspend (Rafael J. Wysocki).
- Clean up unnecessary local variable initializations in multiple
places in the hibernation code (Wang chaodong, Li zeming).
- Adjust core hibernation code to avoid missing wakeup events that
occur after saving an image to persistent storage (Chris Feng).
- Update hibernation code to enforce correct ordering during image
compression and decompression (Hongchen Zhang).
- Use kmap_local_page() instead of kmap_atomic() in copy_data_page()
during hibernation and restore (Chen Haonan).
- Adjust documentation and code comments to reflect recent tasks freezer
changes (Kevin Hao).
- Repair excess function parameter description warning in the
hibernation image-saving code (Randy Dunlap).
- Fix _set_required_opps when opp is NULL (Bryan O'Donoghue).
- Use device_get_match_data() in the OPP code for TI (Rob Herring).
- Clean up OPP level and other parts and call dev_pm_opp_set_opp()
recursively for required OPPs (Viresh Kumar).
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAmWb8o8SHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRxbOQP/2D+YGyd9R1awYqxQoIQSGbpIr7a9oTR
BOIcOn2PvWLXH8w9wVbIUJsSL9Nx90D9T4S5QcyHrS2qHmR+1Gb0gX3D4QAmEBcG
+wFCLt2//5PwqShtPcJEUcGdL274aVEpmnEAmzKnk20MkLQM3twxe6FKSkwWMLYb
u9OKgdN8Vah0iSBUCpyT52O0x4d65MD/tka0QaGjLg64TtyqhTSKi+XgWtZkSZ7H
lRgn9qMoMXq/h1aeK4MKp5UtJKRxBWRdMijIFFXAfgO8dwbDbyXTo0d2LMR6DiEM
VsvRIjEePoRcGf7bwAbrUeSoNb5Ec32RW3v9GSNn2sWutW+vhD//frZq48zAR6lm
i8Xlf2Ar63Z+qNcFpCZjlNwAbfEuZ1vIr0Pu3oDd0GkOXjxiVMgAwtatTp1nSW7/
wWFuMA5G+wdzU/Z5KcV1p7S8CP1gC8S05LHGwtKKGm9pLbzhauF8GK6Xpa4711T8
oI3uDFIgxaxW8B/ymsM5cNa2QbfYUuQbOFTwXvBcy4gizrbZwwXRSpfaKoDIYAXZ
2kfwmFbu3IbrRypboY58lG3SzbnN94oEMANtsVYuxMimGz2x3ZmHBAFm2l9YPYRz
dBq/RUM7sMIvM1SwqR4tG8rt206L7KpPyW99pUa2AhEdof4iV2bpyujHFdkm83MK
nJ0OF/xcc98Z
=zh4c
-----END PGP SIGNATURE-----
Merge tag 'pm-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These add support for new processors (Sierra Forest, Grand Ridge and
Meteor Lake) to the intel_idle driver, make intel_pstate run on
Emerald Rapids without HWP support and adjust it to utilize EPP values
supplied by the platform firmware, fix issues, clean up code and
improve documentation.
The most significant fix addresses deadlocks in the core system-wide
resume code that occur if async_schedule_dev() attempts to run its
argument function synchronously (for example, due to a memory
allocation failure). It rearranges the code in question which may
increase the system resume time in some cases, but this basically is a
removal of a premature optimization. That optimization will be added
back later, but properly this time.
Specifics:
- Add support for the Sierra Forest, Grand Ridge and Meteorlake SoCs
to the intel_idle cpuidle driver (Artem Bityutskiy, Zhang Rui)
- Do not enable interrupts when entering idle in the haltpoll cpuidle
driver (Borislav Petkov)
- Add Emerald Rapids support in no-HWP mode to the intel_pstate
cpufreq driver (Zhenguo Yao)
- Use EPP values programmed by the platform firmware as balanced
performance ones by default in intel_pstate (Srinivas Pandruvada)
- Add a missing function return value check to the SCMI cpufreq
driver to avoid unexpected behavior (Alexandra Diupina)
- Fix parameter type warning in the armada-8k cpufreq driver (Gregory
CLEMENT)
- Rework trans_stat_show() in the devfreq core code to avoid buffer
overflows (Christian Marangi)
- Synchronize devfreq_monitor_[start/stop] so as to prevent a timer
list corruption from occurring when devfreq governors are switched
frequently (Mukesh Ojha)
- Fix possible deadlocks in the core system-wide PM code that occur
if device-handling functions cannot be executed asynchronously
during resume from system-wide suspend (Rafael J. Wysocki)
- Clean up unnecessary local variable initializations in multiple
places in the hibernation code (Wang chaodong, Li zeming)
- Adjust core hibernation code to avoid missing wakeup events that
occur after saving an image to persistent storage (Chris Feng)
- Update hibernation code to enforce correct ordering during image
compression and decompression (Hongchen Zhang)
- Use kmap_local_page() instead of kmap_atomic() in copy_data_page()
during hibernation and restore (Chen Haonan)
- Adjust documentation and code comments to reflect recent tasks
freezer changes (Kevin Hao)
- Repair excess function parameter description warning in the
hibernation image-saving code (Randy Dunlap)
- Fix _set_required_opps when opp is NULL (Bryan O'Donoghue)
- Use device_get_match_data() in the OPP code for TI (Rob Herring)
- Clean up OPP level and other parts and call dev_pm_opp_set_opp()
recursively for required OPPs (Viresh Kumar)"
* tag 'pm-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (35 commits)
OPP: Rename 'rate_clk_single'
OPP: Pass rounded rate to _set_opp()
OPP: Relocate dev_pm_opp_sync_regulators()
PM: sleep: Fix possible deadlocks in core system-wide PM code
OPP: Move dev_pm_opp_icc_bw to internal opp.h
async: Introduce async_schedule_dev_nocall()
async: Split async_schedule_node_domain()
cpuidle: haltpoll: Do not enable interrupts when entering idle
OPP: Fix _set_required_opps when opp is NULL
OPP: The level field is always of unsigned int type
PM: hibernate: Repair excess function parameter description warning
PM: sleep: Remove obsolete comment from unlock_system_sleep()
cpufreq: intel_pstate: Add Emerald Rapids support in no-HWP mode
Documentation: PM: Adjust freezing-of-tasks.rst to the freezer changes
PM: hibernate: Use kmap_local_page() in copy_data_page()
intel_idle: add Sierra Forest SoC support
intel_idle: add Grand Ridge SoC support
PM / devfreq: Synchronize devfreq_monitor_[start/stop]
cpufreq: armada-8k: Fix parameter type warning
PM: hibernate: Enforce ordering during image compression/decompression
...
- Check return value of a function in SCMI cpufreq driver (Alexandra Diupina).
- Use 'NULL' instead of '0' in Armada cpufreq driver (Gregory CLEMENT).
-----BEGIN PGP SIGNATURE-----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=NLsd
-----END PGP SIGNATURE-----
Merge tag 'cpufreq-arm-updates-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm into pm-cpufreq
Merge ARM cpufreq updates for 6.8 from Viresh Kumar:
"- Check return value of a function in SCMI cpufreq driver (Alexandra
Diupina).
- Use 'NULL' instead of '0' in Armada cpufreq driver (Gregory
CLEMENT)."
* tag 'cpufreq-arm-updates-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: armada-8k: Fix parameter type warning
cpufreq: scmi: process the result of devm_of_clk_add_hw_provider()
Move and rename cppc_cpufreq_perf_to_khz() and cppc_cpufreq_khz_to_perf() to
use them outside cppc_cpufreq in topology_init_cpu_capacity_cppc().
Modify the interface to use struct cppc_perf_caps *caps instead of
struct cppc_cpudata *cpu_data as we only use the fields of cppc_perf_caps.
cppc_cpufreq was converting the lowest and nominal freq from MHz to kHz
before using them. We move this conversion inside cppc_perf_to_khz and
cppc_khz_to_perf to make them generic and usable outside cppc_cpufreq.
No functional change
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Pierre Gondois <pierre.gondois@arm.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20231211104855.558096-6-vincent.guittot@linaro.org
cpuinfo.max_freq can change at runtime because of boost as an example. This
implies that the value could be different from the frequency that has been
used to compute the capacity of a CPU.
The new arch_scale_freq_ref() returns a fixed and coherent frequency
that can be used to compute the capacity for a given frequency.
[ Also fix a arch_set_freq_scale() newline style wart in <linux/cpufreq.h>. ]
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Link: https://lore.kernel.org/r/20231211104855.558096-3-vincent.guittot@linaro.org
Users may disable HWP in firmware, in which case intel_pstate will give up
unless the CPU model is explicitly supported.
See also the following past commits:
- commit df51f287b5 ("cpufreq: intel_pstate: Add Sapphire Rapids support
in no-HWP mode")
- commit d8de7a44e1 ("cpufreq: intel_pstate: Add Skylake servers support")
- commit 706c532885 ("cpufreq: intel_pstate: Add Cometlake support in
no-HWP mode")
- commit fbdc21e9b0 ("cpufreq: intel_pstate: Add Icelake servers support in
no-HWP mode")
- commit 71bb5c82aa ("cpufreq: intel_pstate: Add Tigerlake support in
no-HWP mode")
Signed-off-by: Zhenguo Yao <yaozhenguo1@gmail.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The second parameter of clk_get() is of type 'const char *', so use
NULL instead of the integer 0 to resolve a sparse warning:
drivers/cpufreq/armada-8k-cpufreq.c:60:40: warning: Using plain integer as NULL pointer
drivers/cpufreq/armada-8k-cpufreq.c:168:40: warning: Using plain integer as NULL pointer
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
devm_of_clk_add_hw_provider() may return an errno, so
add a return value check
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 8410e7f3b3 ("cpufreq: scmi: Fix OPP addition failure with a dummy clock provider")
Signed-off-by: Alexandra Diupina <adiupina@astralinux.ru>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The platform firmware can provide a balance performance EPP value by
enabling HWP and programming the EPP to the desired value.
However, currently this only takes effect for processors listed in
intel_epp_balance_perf[], so in order to enable a new processor model
to utilize this mechanism, that table needs to be updated. It arguably
should not be necessary to modify the kernel to work properly with
every new generation of processors, though, and distributions that don't
always ship the most recent kernels should be able to run reasonably well
on new hardware without code changes.
For this reason, move the check to avoid updating the EPP when the balance
performance EPP is unmodified from the power-up default of 0x80 after the
check that allows the firmware-provided balance performance EPP value to
be retrieved. This will cause the code to always look for the firmware-
provided value before consulting intel_epp_balance_perf[] and the handling
of new hardware will not depend on whether or not that thable has been
updated yet.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When amd_pstate is running, writing to scaling_min_freq and
scaling_max_freq has no effect. These values are only passed to the
policy level, but not to the platform level. This means that the
platform does not know about the frequency limits set by the user.
To fix this, update the min_perf and max_perf values at the platform
level whenever the user changes the scaling_min_freq and scaling_max_freq
values.
Fixes: ffa5096a7c ("cpufreq: amd-pstate: implement Pstate EPP support for the AMD processors")
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Wyes Karny <wyes.karny@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_driver->fast_switch() callback expects a frequency as a return
value. amd_pstate_fast_switch() was returning the return value of
amd_pstate_update_freq(), which only indicates a success or failure.
Fix this by making amd_pstate_fast_switch() return the target_freq
when the call to amd_pstate_update_freq() is successful, and return
the current frequency from policy->cur when the call to
amd_pstate_update_freq() is unsuccessful.
Fixes: 4badf2eb1e ("cpufreq: amd-pstate: Add ->fast_switch() callback")
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Wyes Karny <wyes.karny@amd.com>
Reviewed-by: Perry Yuan <perry.yuan@amd.com>
Cc: 6.4+ <stable@vger.kernel.org> # v6.4+
Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
>From the Linux point of view, the power domains used by the CPU must
stay always-on. This is because we still need the CPU to keep running
until the last instruction, which will typically be a firmware call that
shuts down the CPU cleanly.
At the moment the power domain votes (enable + performance state) are
dropped during system suspend, which means the CPU could potentially
malfunction while entering suspend.
We need to distinguish between two different setups used with
qcom-cpufreq-nvmem:
1. CPR power domain: The backing regulator used by CPR should stay
always-on in Linux; it is typically disabled automatically by
hardware when the CPU enters a deep idle state. However, we
should pause the CPR state machine during system suspend.
2. RPMPD: The power domains used by the CPU should stay always-on
in Linux (also across system suspend). The CPU typically only
uses the *_AO ("active-only") variants of the power domains in
RPMPD. For those, the RPM firmware will automatically drop
the votes internally when the CPU enters a deep idle state.
Make this work correctly by calling device_set_awake_path() on the
virtual genpd devices, so that the votes are maintained across system
suspend. The power domain drivers need to set GENPD_FLAG_ACTIVE_WAKEUP
to opt into staying on during system suspend.
For now we only set this for the RPMPD case. For CPR, not setting it
will ensure the state machine is still paused during system suspend,
while the backing regulator will stay on with "regulator-always-on".
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The genpd core caches performance state votes from devices that are
runtime suspended as of commit 3c5a272202 ("PM: domains: Improve
runtime PM performance state handling"). They get applied once the
device becomes active again.
To attach the power domains needed by qcom-cpufreq-nvmem the OPP core
calls genpd_dev_pm_attach_by_id(). This results in "virtual" dummy
devices that use runtime PM only to control the enable and performance
state for the attached power domain.
However, at the moment nothing ever resumes the virtual devices created
for qcom-cpufreq-nvmem. They remain permanently runtime suspended. This
means that performance state votes made during cpufreq scaling get
always cached and never applied to the hardware.
Fix this by enabling the devices after attaching them.
Without this fix performance states votes are silently ignored, and the
CPU/CPR voltage is never adjusted. This has been broken since 5.14 but
for some reason no one noticed this on QCS404 so far.
Fixes: 1cb8339ca2 ("cpufreq: qcom: Add support for qcs404 on nvmem driver")
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
For a 900MHz i.MX6ULL CPU the 792MHz OPP is disabled. There is no
convincing reason to disable this OPP. If a CPU can run at 900MHz,
it should also be able to cope with 792MHz. Looking at the voltage
level of 792MHz in [1] (page 24, table 10. "Operating Ranges") the
current defined OPP is above the minimum. So the voltage level
shouldn't be a problem. However in [2] (page 24, table 10.
"Operating Ranges"), it is not mentioned that 792MHz OPP isn't
allowed. Change it to only disable 792MHz OPP for i.MX6ULL types
below 792 MHz.
[1] https://www.nxp.com/docs/en/data-sheet/IMX6ULLIEC.pdf
[2] https://www.nxp.com/docs/en/data-sheet/IMX6ULLCEC.pdf
Fixes: 0aa9abd4c2 ("cpufreq: imx6q: check speed grades for i.MX6ULL")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
[ Viresh: Edited subject ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
- Add support for several Qualcomm SoC versions (Robert Marko and
Varadarajan Narayanan).
-----BEGIN PGP SIGNATURE-----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=yM+b
-----END PGP SIGNATURE-----
Merge tag 'cpufreq-arm-updates-6.7-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Merge ARM cpufreq updates for 6.7 (part 2) from Viresh kumar:
"- Add support for several Qualcomm SoC versions (Robert Marko and
Varadarajan Narayanan)."
* tag 'cpufreq-arm-updates-6.7-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: qcom-nvmem: Introduce cpufreq for ipq95xx
cpufreq: qcom-nvmem: Enable cpufreq for ipq53xx
cpufreq: qcom-nvmem: add support for IPQ8074
soc: qcom: socinfo: Add IDs for IPQ8174 family
dt-bindings: arm: qcom,ids: Add IDs for IPQ8174 family
dt-bindings: qcom: geni-se: Allow dma-coherent
soc: qcom: socinfo: Add SoC ID for QCM6490
dt-bindings: arm: qcom,ids: Add SoC ID for QCM6490
soc: qcom: socinfo: Add SM8550-adjacent PMICs
soc: qcom: wcnss_ctrl: Remove redundant initialization owner in wcnss_ctrl_driver
soc: qcom: socinfo: Add Soc ID for SM7150P
dt-bindings: arm: qcom,ids: Add Soc ID for SM7150P
firmware: Add support for Qualcomm UEFI Secure Application
firmware: qcom_scm: Add support for Qualcomm Secure Execution Environment SCM interface
lib/ucs2_string: Add UCS-2 strscpy function
IPQ95xx SoCs have different OPPs available for the CPU based on
the SoC variant. This can be determined from an eFuse register
present in the silicon.
Added support for ipq95xx on nvmem driver which helps to
determine OPPs at runtime based on the eFuse register which
has the CPU frequency limits. opp-supported-hw dt binding
can be used to indicate the available OPPs for each limit.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Praveenkumar I <ipkumar@codeaurora.org>
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
[ Viresh: Fixed subject ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
IPQ53xx have different OPPs available for the CPU based on
SoC variant. This can be determined through use of an eFuse
register present in the silicon.
Added support for ipq53xx on nvmem driver which helps to
determine OPPs at runtime based on the eFuse register which
has the CPU frequency limits. opp-supported-hw dt binding
can be used to indicate the available OPPs for each limit.
nvmem driver also creates the "cpufreq-dt" platform_device after
passing the version matching data to the OPP framework so that the
cpufreq-dt handles the actual cpufreq implementation.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
[ Viresh: Fixed subject ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
IPQ8074 comes in 3 families:
* IPQ8070A/IPQ8071A (Acorn) up to 1.4GHz
* IPQ8172/IPQ8173/IPQ8174 (Oak) up to 1.4GHz
* IPQ8072A/IPQ8074A/IPQ8076A/IPQ8078A (Hawkeye) up to 2.2GHz
So, in order to be able to share one OPP table lets add support for IPQ8074
family based of SMEM SoC ID-s as speedbin fuse is always 0 on IPQ8074.
IPQ8074 compatible is blacklisted from DT platdev as the cpufreq device
will get created by NVMEM CPUFreq driver.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
[ Viresh: Fixed rebase conflict. ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The ia64 architecture gets its well-earned retirement as planned,
now that there is one last (mostly) working release that will
be maintained as an LTS kernel.
The architecture specific system call tables are updated for
the added map_shadow_stack() syscall and to remove references
to the long-gone sys_lookup_dcookie() syscall.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmVC40IACgkQYKtH/8kJ
Uidhmw/9EX+aWSXGoObJ3fngaNSMw+PmrEuP8qEKBHxfKHcCdX3hc451Oh4GlhaQ
tru91pPwgNvN2/rfoKusxT+V4PemGIzfNni/04rp+P0kvmdw5otQ2yNhsQNsfVmq
XGWvkxF4P2GO6bkjjfR/1dDq7GtlyXtwwPDKeLbYb6TnJOZjtx+EAN27kkfSn1Ms
R4Sa3zJ+DfHUmHL5S9g+7UD/CZ5GfKNmIskI4Mz5GsfoUz/0iiU+Bge/9sdcdSJQ
kmbLy5YnVzfooLZ3TQmBFsO3iAMWb0s/mDdtyhqhTVmTUshLolkPYyKnPFvdupyv
shXcpEST2XJNeaDRnL2K4zSCdxdbnCZHDpjfl9wfioBg7I8NfhXKpf1jYZHH1de4
LXq8ndEFEOVQw/zSpYWfQq1sux8Jiqr+UK/ukbVeFWiGGIUs91gEWtPAf8T0AZo9
ujkJvaWGl98O1g5wmBu0/dAR6QcFJMDfVwbmlIFpU8O+MEaz6X8mM+O5/T0IyTcD
eMbAUjj4uYcU7ihKzHEv/0SS9Of38kzff67CLN5k8wOP/9NlaGZ78o1bVle9b52A
BdhrsAefFiWHp1jT6Y9Rg4HOO/TguQ9e6EWSKOYFulsiLH9LEFaB9RwZLeLytV0W
vlAgY9rUW77g1OJcb7DoNv33nRFuxsKqsnz3DEIXtgozo9CzbYI=
=H1vH
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull ia64 removal and asm-generic updates from Arnd Bergmann:
- The ia64 architecture gets its well-earned retirement as planned,
now that there is one last (mostly) working release that will be
maintained as an LTS kernel.
- The architecture specific system call tables are updated for the
added map_shadow_stack() syscall and to remove references to the
long-gone sys_lookup_dcookie() syscall.
* tag 'asm-generic-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
hexagon: Remove unusable symbols from the ptrace.h uapi
asm-generic: Fix spelling of architecture
arch: Reserve map_shadow_stack() syscall number for all architectures
syscalls: Cleanup references to sys_lookup_dcookie()
Documentation: Drop or replace remaining mentions of IA64
lib/raid6: Drop IA64 support
Documentation: Drop IA64 from feature descriptions
kernel: Drop IA64 support from sig_fault handlers
arch: Remove Itanium (IA-64) architecture
The highlights for the driver support this time are
- Qualcomm platforms gain support for the Qualcomm Secure Execution
Environment firmware interface to access EFI variables on certain
devices, and new features for multiple platform and firmware drivers.
- Arm FF-A firmware support gains support for v1.1 specification features,
in particular notification and memory transaction descriptor changes.
- SCMI firmware support now support v3.2 features for clock and DVFS
configuration and a new transport for Qualcomm platforms.
- Minor cleanups and bugfixes are added to pretty much all the active
platforms: qualcomm, broadcom, dove, ti-k3, rockchip, sifive, amlogic,
atmel, tegra, aspeed, vexpress, mediatek, samsung and more.
In particular, this contains portions of the treewide conversion to
use __counted_by annotations and the device_get_match_data helper.
-----BEGIN PGP SIGNATURE-----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=QIut
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"The highlights for the driver support this time are
- Qualcomm platforms gain support for the Qualcomm Secure Execution
Environment firmware interface to access EFI variables on certain
devices, and new features for multiple platform and firmware
drivers.
- Arm FF-A firmware support gains support for v1.1 specification
features, in particular notification and memory transaction
descriptor changes.
- SCMI firmware support now support v3.2 features for clock and DVFS
configuration and a new transport for Qualcomm platforms.
- Minor cleanups and bugfixes are added to pretty much all the active
platforms: qualcomm, broadcom, dove, ti-k3, rockchip, sifive,
amlogic, atmel, tegra, aspeed, vexpress, mediatek, samsung and
more.
In particular, this contains portions of the treewide conversion to
use __counted_by annotations and the device_get_match_data helper"
* tag 'soc-drivers-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (156 commits)
soc: qcom: pmic_glink_altmode: Print return value on error
firmware: qcom: scm: remove unneeded 'extern' specifiers
firmware: qcom: scm: add a missing forward declaration for struct device
firmware: qcom: move Qualcomm code into its own directory
soc: samsung: exynos-chipid: Convert to platform remove callback returning void
soc: qcom: apr: Add __counted_by for struct apr_rx_buf and use struct_size()
soc: qcom: pmic_glink: fix connector type to be DisplayPort
soc: ti: k3-socinfo: Avoid overriding return value
soc: ti: k3-socinfo: Fix typo in bitfield documentation
soc: ti: knav_qmss_queue: Use device_get_match_data()
firmware: ti_sci: Use device_get_match_data()
firmware: qcom: qseecom: add missing include guards
soc/pxa: ssp: Convert to platform remove callback returning void
soc/mediatek: mtk-mmsys: Convert to platform remove callback returning void
soc/mediatek: mtk-devapc: Convert to platform remove callback returning void
soc/loongson: loongson2_guts: Convert to platform remove callback returning void
soc/litex: litex_soc_ctrl: Convert to platform remove callback returning void
soc/ixp4xx: ixp4xx-qmgr: Convert to platform remove callback returning void
soc/ixp4xx: ixp4xx-npe: Convert to platform remove callback returning void
soc/hisilicon: kunpeng_hccs: Convert to platform remove callback returning void
...
- Add support for several Qualcomm SoC versions and other similar
changes (Christian Marangi, Dmitry Baryshkov, Luca Weiss, Neil
Armstrong, Richard Acayan, Robert Marko, Rohit Agarwal, Stephan
Gerhold and Varadarajan Narayanan).
- Clean up the tegra cpufreq driver (Sumit Gupta).
- Use of_property_read_reg() to parse "reg" in pmac32 driver (Rob
Herring).
- Add support for TI's am62p5 Soc (Bryan Brattlof).
- Make ARM_BRCMSTB_AVS_CPUFREQ depends on !ARM_SCMI_CPUFREQ (Florian
Fainelli).
- Update Kconfig to mention i.MX7 as well (Alexander Stein).
- Revise global turbo disable check in intel_pstate (Srinivas
Pandruvada).
- Carry out initialization of sg_cpu in the schedutil cpufreq governor
in one loop (Liao Chang).
- Simplify the condition for storing 'down_threshold' in the
conservative cpufreq governor (Liao Chang).
- Use fine-grained mutex in the userspace cpufreq governor (Liao
Chang).
- Move is_managed indicator in the userspace cpufreq governor into a
per-policy structure (Liao Chang).
- Rebuild sched-domains when removing cpufreq driver (Pierre Gondois).
- Fix buffer overflow detection in trans_stats() (Christian Marangi).
- Switch to dev_pm_opp_find_freq_(ceil/floor)_indexed() APIs to support
specific devices like UFS which handle multiple clocks through OPP
(Operating Performance Point) framework (Manivannan Sadhasivam).
- Add perf support to the Rockchip DFI (DDR Monitor Module) devfreq-
event driver:
* Generalize rockchip-dfi.c to support new RK3568/RK3588 using
different DDR type (Sascha Hauer).
* Convert DT binding document format to yaml (Sascha Hauer).
* Add perf support for DFI (a unit suitable for measuring DDR
utilization) to rockchip-dfi.c to extend DFI usage (Sascha Hauer).
- Add locking to the OPP handling code in the Mediatek CCI devfreq
driver, because the voltage of shared OPP might be changed by
multiple drivers (Mark Tseng, Dan Carpenter).
- Use device_get_match_data() in the Samsung Exynos PPMU devfreq-event
driver (Rob Herring).
- Extend support for the opp-level beyond required-opps (Ulf Hansson).
- Add dev_pm_opp_find_level_floor() (Krishna chaitanya chundru).
- dt-bindings: Allow opp-peak-kBpsfor kryo CPUs, support Qualcomm Krait
SoCs and document named opp-microvolt property (Bjorn Andersson,
Dmitry Baryshkov and Christian Marangi).
- Fix -Wunsequenced warning _of_add_opp_table_v1() (Nathan Chancellor).
- General cleanup of OPP code (Viresh Kumar).
- Use __get_safe_page() rather than touching the list in hibernation
snapshot code (Brian Geffon).
- Fix symbol export for _SIMPLE_ variants of _PM_OPS() (Raag Jadav).
- Clean up sync_read handling in snapshot_write_next() (Brian Geffon).
- Fix kerneldoc comments for swsusp_check() and swsusp_close() to
better match code (Christoph Hellwig).
- Downgrade BIOS locked limits pr_warn() in the Intel RAPL power
capping driver to pr_debug() (Ville Syrjälä).
- Change the minimum python version for the intel_pstate_tracer utility
from 2.7 to 3.6 (Doug Smythies).
-----BEGIN PGP SIGNATURE-----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=h8my
-----END PGP SIGNATURE-----
Merge tag 'pm-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These add new hardware support (new Qualcomm SoC versions in cpufreq,
RK3568/RK3588 in devfreq), extend the OPP (operating performance
points) framework, improve cpufreq governors, fix issues and clean up
code (most of the changes are in cpufreq and devfreq).
Specifics:
- Add support for several Qualcomm SoC versions and other similar
changes (Christian Marangi, Dmitry Baryshkov, Luca Weiss, Neil
Armstrong, Richard Acayan, Robert Marko, Rohit Agarwal, Stephan
Gerhold and Varadarajan Narayanan)
- Clean up the tegra cpufreq driver (Sumit Gupta)
- Use of_property_read_reg() to parse "reg" in pmac32 driver (Rob
Herring)
- Add support for TI's am62p5 Soc (Bryan Brattlof)
- Make ARM_BRCMSTB_AVS_CPUFREQ depends on !ARM_SCMI_CPUFREQ (Florian
Fainelli)
- Update Kconfig to mention i.MX7 as well (Alexander Stein)
- Revise global turbo disable check in intel_pstate (Srinivas
Pandruvada)
- Carry out initialization of sg_cpu in the schedutil cpufreq
governor in one loop (Liao Chang)
- Simplify the condition for storing 'down_threshold' in the
conservative cpufreq governor (Liao Chang)
- Use fine-grained mutex in the userspace cpufreq governor (Liao
Chang)
- Move is_managed indicator in the userspace cpufreq governor into a
per-policy structure (Liao Chang)
- Rebuild sched-domains when removing cpufreq driver (Pierre Gondois)
- Fix buffer overflow detection in trans_stats() (Christian Marangi)
- Switch to dev_pm_opp_find_freq_(ceil/floor)_indexed() APIs to
support specific devices like UFS which handle multiple clocks
through OPP (Operating Performance Point) framework (Manivannan
Sadhasivam)
- Add perf support to the Rockchip DFI (DDR Monitor Module) devfreq-
event driver:
* Generalize rockchip-dfi.c to support new RK3568/RK3588 using
different DDR type (Sascha Hauer).
* Convert DT binding document format to yaml (Sascha Hauer).
* Add perf support for DFI (a unit suitable for measuring DDR
utilization) to rockchip-dfi.c to extend DFI usage (Sascha
Hauer)
- Add locking to the OPP handling code in the Mediatek CCI devfreq
driver, because the voltage of shared OPP might be changed by
multiple drivers (Mark Tseng, Dan Carpenter)
- Use device_get_match_data() in the Samsung Exynos PPMU
devfreq-event driver (Rob Herring)
- Extend support for the opp-level beyond required-opps (Ulf Hansson)
- Add dev_pm_opp_find_level_floor() (Krishna chaitanya chundru)
- dt-bindings: Allow opp-peak-kBpsfor kryo CPUs, support Qualcomm
Krait SoCs and document named opp-microvolt property (Bjorn
Andersson, Dmitry Baryshkov and Christian Marangi)
- Fix -Wunsequenced warning _of_add_opp_table_v1() (Nathan
Chancellor)
- General cleanup of OPP code (Viresh Kumar)
- Use __get_safe_page() rather than touching the list in hibernation
snapshot code (Brian Geffon)
- Fix symbol export for _SIMPLE_ variants of _PM_OPS() (Raag Jadav)
- Clean up sync_read handling in snapshot_write_next() (Brian Geffon)
- Fix kerneldoc comments for swsusp_check() and swsusp_close() to
better match code (Christoph Hellwig)
- Downgrade BIOS locked limits pr_warn() in the Intel RAPL power
capping driver to pr_debug() (Ville Syrjälä)
- Change the minimum python version for the intel_pstate_tracer
utility from 2.7 to 3.6 (Doug Smythies)"
* tag 'pm-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (82 commits)
dt-bindings: cpufreq: qcom-hw: document SM8650 CPUFREQ Hardware
cpufreq: arm: Kconfig: Add i.MX7 to supported SoC for ARM_IMX_CPUFREQ_DT
cpufreq: qcom-nvmem: add support for IPQ8064
cpufreq: qcom-nvmem: also accept operating-points-v2-krait-cpu
cpufreq: qcom-nvmem: drop pvs_ver for format a fuses
dt-bindings: cpufreq: qcom-cpufreq-nvmem: Document krait-cpu
cpufreq: qcom-nvmem: add support for IPQ6018
dt-bindings: cpufreq: qcom-cpufreq-nvmem: document IPQ6018
cpufreq: qcom-nvmem: Add MSM8909
cpufreq: qcom-nvmem: Simplify driver data allocation
powercap: intel_rapl: Downgrade BIOS locked limits pr_warn() to pr_debug()
cpufreq: stats: Fix buffer overflow detection in trans_stats()
dt-bindings: devfreq: event: rockchip,dfi: Add rk3588 support
dt-bindings: devfreq: event: rockchip,dfi: Add rk3568 support
dt-bindings: devfreq: event: convert Rockchip DFI binding to yaml
PM / devfreq: rockchip-dfi: add support for RK3588
PM / devfreq: rockchip-dfi: account for multiple DDRMON_CTRL registers
PM / devfreq: rockchip-dfi: make register stride SoC specific
PM / devfreq: rockchip-dfi: Add perf support
PM / devfreq: rockchip-dfi: give variable a better name
...
- Add support for several Qualcomm SoC versions and other similar
changes (Christian Marangi, Dmitry Baryshkov, Luca Weiss, Neil
Armstrong, Richard Acayan, Robert Marko, Rohit Agarwal, Stephan
Gerhold and Varadarajan Narayanan).
- Cleanups to the tegra cpufreq driver (Sumit Gupta).
- Use of_property_read_reg() to parse "reg" in pmac32 driver (Rob Herring).
- Add support for TI's am62p5 Soc (Bryan Brattlof).
- Make ARM_BRCMSTB_AVS_CPUFREQ depends on !ARM_SCMI_CPUFREQ (Florian
Fainelli).
- Update Kconfig to mention i.MX7 as well (Alexander Stein).
-----BEGIN PGP SIGNATURE-----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=DwUn
-----END PGP SIGNATURE-----
Merge tag 'cpufreq-arm-updates-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Merge ARM cpufreq updates for 6.7 from Viresh Kumar:
"- Add support for several Qualcomm SoC versions and other similar
changes (Christian Marangi, Dmitry Baryshkov, Luca Weiss, Neil
Armstrong, Richard Acayan, Robert Marko, Rohit Agarwal, Stephan
Gerhold and Varadarajan Narayanan).
- Cleanups to the tegra cpufreq driver (Sumit Gupta).
- Use of_property_read_reg() to parse "reg" in pmac32 driver (Rob Herring).
- Add support for TI's am62p5 Soc (Bryan Brattlof).
- Make ARM_BRCMSTB_AVS_CPUFREQ depends on !ARM_SCMI_CPUFREQ (Florian
Fainelli).
- Update Kconfig to mention i.MX7 as well (Alexander Stein)."
* tag 'cpufreq-arm-updates-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm: (25 commits)
dt-bindings: cpufreq: qcom-hw: document SM8650 CPUFREQ Hardware
cpufreq: arm: Kconfig: Add i.MX7 to supported SoC for ARM_IMX_CPUFREQ_DT
cpufreq: qcom-nvmem: add support for IPQ8064
cpufreq: qcom-nvmem: also accept operating-points-v2-krait-cpu
cpufreq: qcom-nvmem: drop pvs_ver for format a fuses
dt-bindings: cpufreq: qcom-cpufreq-nvmem: Document krait-cpu
cpufreq: qcom-nvmem: add support for IPQ6018
dt-bindings: cpufreq: qcom-cpufreq-nvmem: document IPQ6018
cpufreq: qcom-nvmem: Add MSM8909
cpufreq: qcom-nvmem: Simplify driver data allocation
dt-bindings: cpufreq: cpufreq-qcom-hw: Add SDX75 compatible
cpufreq: ARM_BRCMSTB_AVS_CPUFREQ cannot be used with ARM_SCMI_CPUFREQ
cpufreq: ti-cpufreq: Add opp support for am62p5 SoCs
cpufreq: dt-platdev: add am62p5 to blocklist
cpufreq: tegra194: remove redundant AND with cpu_online_mask
cpufreq: tegra194: use refclk delta based loop instead of udelay
cpufreq: tegra194: save CPU data to avoid repeated SMP calls
dt-bindings: cpufreq: cpufreq-qcom-hw: add SDM670 compatible
dt-bindings: cpufreq: qcom-nvmem: Document MSM8909
cpufreq: dt: platdev: Add MSM8909 to blocklist
...
Since commit a5a9dffcc9 ("ARM: imx: Switch imx7d to imx-cpufreq-dt
for speed-grading") i.MX7 uses this driver as well. Add it to the
description text.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
IPQ8064 comes in 3 families:
* IPQ8062 up to 1.0GHz
* IPQ8064/IPQ8066/IPQ8068 up to 1.4GHz
* IPQ8065/IPQ8069 up to 1.7Ghz
So, in order to be able to support one OPP table, add support for
IPQ8064 family based of SMEM SoC ID-s and correctly set the version so
opp-supported-hw can be correctly used.
Bit are set with the following logic:
* IPQ8062 BIT 0
* IPQ8064/IPQ8066/IPQ8068 BIT 1
* IPQ8065/IPQ8069 BIT 2
speed is never fused, only pvs values are fused.
IPQ806x SoC doesn't have pvs_version so we drop and we use the new
pattern:
opp-microvolt-speed0-pvs<PSV_VALUE>
Example:
- for ipq8062 psv2
opp-microvolt-speed0-pvs2 = < 925000 878750 971250>
Fixes: a8811ec764 ("cpufreq: qcom: Add support for krait based socs")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
[ Viresh: Fixed rebase conflict. ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
the qcom-cpufreq-nvmem driver attempts to support both Qualcomm Kryo
(newer 64-bit ARMv8 cores) and Krait (older 32-bit ARMv7 cores). It
makes no sense to use 'operating-points-v2-kryo-cpu' compatibility node
for the Krait cores. Add support for 'operating-points-v2-krait-cpu'
compatibility string.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The fuses used on msm8960 / apq8064 / ipq806x families of devices do not
have the pvs version. Drop this argument from parsing function.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
IPQ6018 SoC series comes in multiple SKU-s, and not all of them support
high frequency OPP points.
SoC itself does however have a single bit in QFPROM to indicate the CPU
speed-bin.
That bit is used to indicate frequency limit of 1.5GHz, but that alone is
not enough as IPQ6000 only goes up to 1.2GHz, but SMEM ID can be used to
limit it further.
IPQ6018 compatible is blacklisted from DT platdev as the cpufreq device
will get created by NVMEM CPUFreq driver.
Signed-off-by: Robert Marko <robimarko@gmail.com>
[ Viresh: Fixed rebase conflict. ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
When the MSM8909 SoC is used together with the PM8909 PMIC the primary
power supply for the CPU (VDD_APC) is shared with other components to
the SoC, namely the VDD_CX power domain typically supplied by the PM8909
S1 regulator. This means that all votes for necessary performance states
go via the RPM firmware which collects the requirements from all the
processors in the SoC. The RPM firmware then chooses the actual voltage
based on the performance states ("corners"), depending on calibration
values in the NVMEM and other factors.
The MSM8909 SoC is also sometimes used with the PM8916 or PM660 PMIC.
In that case there is a dedicated regulator connected to VDD_APC and
Linux is responsible to do adaptive voltage scaling using CPR (similar
to the existing code for QCS404).
This difference can be described in the device tree, by either assigning
the CPU a power domain from RPMPD or from the CPR driver.
Describe this using "perf" as generic power domain name, which is also
used already for SCMI based platforms.
Also add a simple function that reads the speedbin from a NVMEM cell
and sets it as-is for opp-supported-hw. The actual bit position can be
described in the device tree without additional driver changes.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
[ Viresh: Fixed rebase conflict. ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Simplify the allocation and cleanup of driver data by using devm
together with a flexible array. Prepare for adding additional per-CPU
data by defining a struct qcom_cpufreq_drv_cpu instead of storing the
opp_tokens directly.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Commit 3c0897c180 ("cpufreq: Use scnprintf() for avoiding potential
buffer overflow") switched from snprintf to the more secure scnprintf
but never updated the exit condition for PAGE_SIZE.
As the commit say and as scnprintf document, what scnprintf returns what
is actually written not counting the '\0' end char. This results in the
case of len exceeding the size, len set to PAGE_SIZE - 1, as it can be
written at max PAGE_SIZE - 1 (as '\0' is not counted)
Because of len is never set to PAGE_SIZE, the function never break early,
never prints the warning and never return -EFBIG.
Fix this by changing the condition to PAGE_SIZE - 1 to correctly trigger
the error.
Cc: 5.10+ <stable@vger.kernel.org> # 5.10+
Fixes: 3c0897c180 ("cpufreq: Use scnprintf() for avoiding potential buffer overflow")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The brcmstb-avs-cpufreq driver is considered a legacy driver and since
2018, ARCH_BRCMSTB systems have been using scmi-cpufreq. As a matter of
fact, when SCMI is in use, brcmstb-avs-cpufreq is unusable since the
SCMI firmware takes over, this can result in various problems, including
external synchronous aborts.
Express those constraints such that the driver is not enabled by default
when SCMI CPU frequency scaling is in use.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The am62p5 is a variation of the am625 and the am62a7 SoC families. Add
the am62p5 to the list using the same cpufreq data as the rest of the
am62x extended family.
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
