Since the configuration order between the individual MSTOP and CLKON
bits cannot be preserved with the power domain abstraction, drop the
power domain core code.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/20250527112403.1254122-7-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RZ/{G2L,V2L,G3S} CPG versions support a feature called MSTOP. Each
module has one or more MSTOP bits associated with it, and these bits
need to be configured along with the module clocks. Setting the MSTOP
bits switches the module between normal and standby states.
Previously, MSTOP support was abstracted through power domains (struct
generic_pm_domain::{power_on, power_off} APIs). With this abstraction,
the order of setting the MSTOP and CLKON bits was as follows:
Previous Order:
A/ Switching to Normal State (e.g., during probe):
1/ Clear module MSTOP bit
2/ Set module CLKON bit
B/ Switching to Standby State (e.g., during remove):
1/ Clear CLKON bit
2/ Set MSTOP bit
However, in some cases (when the clock is disabled through devres), the
order may have been (due to the issue described in link section):
1/ Set MSTOP bit
2/ Clear CLKON bit
Recently, the hardware team has suggested that the correct order to set
the MSTOP and CLKON bits is:
Updated Order:
A/ Switching to Normal State (e.g., during probe):
1/ Set CLKON bit
2/ Clear MSTOP bit
B/ Switching to Standby State (e.g., during remove):
1/ Set MSTOP bit
2/ Clear CLKON bit
To prevent future issues due to incorrect ordering, the MSTOP setup has
now been implemented in rzg2l_mod_clock_endisable(), ensuring compliance
with the sequence suggested in Figure 41.5: Module Standby Mode
Procedure from the RZ/G3S HW manual, Rev1.10.
Additionally, since multiple clocks of a single module may be mapped to
a single MSTOP bit, MSTOP setup is reference-counted.
Furthermore, as all modules start in the normal state after reset, if
the module clocks are disabled, the module state is switched to standby.
This prevents keeping the module in an invalid state, as recommended by
the hardware team.
Link: https://lore.kernel.org/all/20250215130849.227812-1-claudiu.beznea.uj@bp.renesas.com/
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250527112403.1254122-5-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On the RZ/G3S SoC, the CPU PLL settings can be set and retrieved through
the CPG_PLL1_CLK1 and CPG_PLL1_CLK2 registers. However, these settings
are applied only when CPG_PLL1_SETTING.SEL_PLL1 is set to 0.
Otherwise, the CPU PLL operates at the default frequency of 1.1 GHz.
Hence add support to the PLL driver for returning the 1.1 GHz frequency
when the CPU PLL is configured with the default frequency.
Fixes: 01eabef547 ("clk: renesas: rzg2l: Add support for RZ/G3S PLL")
Fixes: de60a3ebe4 ("clk: renesas: Add minimal boot support for RZ/G3S SoC")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250115142059.1833063-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add clock and reset entries for the DRP-AI block, which is available only
on the Renesas RZ/V2L SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250106202853.262787-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
For watchdog PM domain it is necessary to provide GENPD_FLAG_IRQ_SAFE flag
to be able to power on the watchdog PM domain from atomic context. For
this, adjust the current infrastructure to be able to provide GENPD_FLAG_*
for individual PM domains.
With this, remove the always_on flag from rzg2l_cpg_add_pm_domains() as
it is not necessary anymore.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/20241015164732.4085249-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
RZ/{G2L, V2L, G3S}-based CPG versions have support for saving extra
power when clocks are disabled by activating module standby. This is
done through MSTOP-specific registers that are part of CPG. Each
individual module has one or more bits associated with one MSTOP
register (see table "Registers for Module Standby Mode" from HW
manuals). Hardware manual associates modules' clocks with one or more
MSTOP bits. There are 3 mappings available (identified by researching
RZ/G2L, RZ/G3S, RZ/V2L HW manuals):
case 1: N clocks mapped to N MSTOP bits (with N={0, ..., X})
case 2: N clocks mapped to 1 MSTOP bit (with N={0, ..., X})
case 3: N clocks mapped to M MSTOP bits (with N={0, ..., X}, M={0, ..., Y})
Case 3 has been currently identified on RZ/V2L for the VCPL4 module.
To cover all three cases, the individual platform drivers will provide
the clock driver with MSTOP register offsets and associated bits in this
register as a bitmask, and the clock driver will apply this bitmask to
the proper MSTOP register.
The MSTOP support was implemented through power domains.
Platform-specific clock drivers will register an array of type struct
rzg2l_cpg_pm_domain_init_data, which will be used to instantiate
properly the power domains.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20240422105355.1622177-7-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add minimal clock and reset support for the RZ/G3S SoC to be able to
boot Linux from SD Card/eMMC. This includes necessary core clocks for
booting and GIC, SCIF, GPIO, and SD0 module clocks and resets.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231006103959.197485-5-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a divider clock driver for RZ/G3S. This will be used on RZ/G3S for
the SDHI, SPI, OCTA, I, I2, I3, P0, P1, P2, and P3 core clocks.
The divider has some limitation for SDHI, OCTA and SPI clocks:
- SDHI div cannot be 1 if parent rate is 800MHz,
- OCTA, SPI div cannot be 1 if parent rate is 400MHz.
To handle these limitations, a notifier is registered from platform
specific clock driver, which makes sure proper actions are taken before
the clock rate is changed, when needed.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231006103959.197485-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Refactor SD MUX driver to be able to reuse the same code on RZ/G3S.
RZ/G2{L,UL} has a limitation with regards to switching the clock source
for SD MUX (MUX clock source has to be switched to 266MHz before
switching b/w 533MHz and 400MHz). Rework the handling of this limitation
to use a clock notifier that is registered according to platform based
initialization data, so the SD MUX code can be reused on RZ/G3S.
As RZ/G2{L,UL} and RZ/G3S use different bits in different registers to
check if the clock switching has been done, this configuration (register
offset, register bits and bitfield width) is now passed through struct
cpg_core_clk::sconf (status configuration) from platform specific
initialization code.
Along with struct cpg_core_clk::sconf the mux table indices are also
passed from platform specific initialization code.
Also, mux flags are now passed to DEF_SD_MUX() as they will be used
later by RZ/G3S.
CPG_WEN_BIT macro has been introduced to select properly the WEN bit
of various registers.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231006103959.197485-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Remove CPG_SDHI_DSEL and its bits from the generic header as RZ/G3S has
different offset registers and bits for this, thus avoid mixing them.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230929053915.1530607-10-claudiu.beznea@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for reading the frequency of PLL1/4/6 as available on
RZ/G3S. The computation formula for the PLL frequency is as follows:
Fout = (nir + nfr / 4096) * Fin / (mr * pr)
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230929053915.1530607-8-claudiu.beznea@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The SD MUX output (SD0) is further divided by 4 in G2{L,UL}. The
divided clock is SD0_DIV4. SD0_DIV4 is registered with
CLK_SET_RATE_PARENT which means a rate request for it is propagated to
the MUX and could reach rzg2l_cpg_sd_clk_mux_set_parent() concurrently
with the users of SD0.
Add proper locking to avoid concurrent accesses on SD MUX set rate
registers.
Fixes: eaff33646f ("clk: renesas: rzg2l: Add SDHI clk mux support")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230929053915.1530607-4-claudiu.beznea@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
flag and mux_flags are intended to keep bit masks. Use u32 type for it.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230912045157.177966-15-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As per the RZ/G2L HW(Rev.1.30 May2023) manual, there are no "write enable"
bits in the CPG_SIPLL5_CLK1 register. So fix the CPG_SIPLL5_CLK register
write by removing the "write enable" bits.
Fixes: 1561380ee7 ("clk: renesas: rzg2l: Add FOUTPOSTDIV clk support")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230518152334.514922-1-biju.das.jz@bp.renesas.com
[geert: Remove CPG_SIPLL5_CLK1_*_WEN bit definitions]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
There are cases where not all CPG_MOD clocks should be assumed to support
PM. For example on the CRU block there is a particular sequence that needs
to be followed to initialize the CSI-2 D-PHY in which individual clocks
need to be turned ON/OFF, due to which Runtime PM support wasn't used by
the CRU CSI-2 driver.
This patch adds support to allow indicating if PM is not supported by the
CPG_MOD clocks. Two new members no_pm_mod_clks and num_no_pm_mod_clks are
added to struct rzg2l_cpg_info so that MOD clocks which do not support PM
can be passed by no_pm_mod_clks[] array and when the driver uses Runtime
PM support the clk ID is matched against the no_pm_mod_clks[] array to see
if the clk is needed to be included as part of Runtime PM.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20221026014227.162121-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Renesas RZ/V2M SoC is very similar to RZ/G2L, though it doesn't have
any CLK_MON registers.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-11-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RZ/V2M doesn't have a matching set of reset monitor regs for each reset
reg like the RZ/G2L. Instead, it has a single CPG_RST_MON reg which has a
single bit per module.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-10-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RZ/V2M SoC doesn't use CLK_MON registers, so make them optional.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-9-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
All of the muxes and dividers that can be modified require the HIWORD
flags, so make the macros set them. It won't affect read only muxes and
dividers.
This will make the clock tables a little easier to read, particularly for
new SoCs coming.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-8-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
We only ever use ARRAY_SIZE() to populate the number of parents, so
move this into the macro to always detect it automatically. This
also makes the tables of clocks a little simpler.
Similarly for the DEF_SD_MUX macro.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-6-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
M3 clock is sourced from DSI Divider (DSIDIVA * DSIDIVB)
This patch add support for DSI divider clk by combining
DSIDIVA and DSIDIVB.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220430114156.6260-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
PLL5 generates FOUTPOSTDIV clk and is sourced by LCDC/DSI modules.
The FOUTPOSTDIV is connected to PLL5_4 MUX. Video clock is sourced
from DSI divider which is connected to PLL5_4 MUX.
This patch adds support for generating FOUTPOSTDIV clk.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220430114156.6260-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The clock structure for RZ/G2UL is almost identical to RZ/G2L SoC with
fewer IP blocks. The IP blocks such as WDT1, GPT, H264, GPU and POEG are
not present on RZ/G2UL.
This patch adds minimal clock and reset entries required to boot the
system on Renesas RZ/G2UL SMARC EVK and binds it with the RZ/G2L CPG core
driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220412161314.13800-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The clock structure for RZ/V2L is almost identical to the RZ/G2L SoC.
The only difference being that RZ/V2L has additional registers to
control clocks and resets for the DRP-AI block.
Reuse r9a07g044-cpg.c, as the clock IDs and reset IDs are the same
between RZ/G2L and RZ/V2L, and add a separate r9a07g054_cpg_info to take
care of the DRP-AI clocks/resets.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220205084006.7142-1-biju.das.jz@bp.renesas.com
Link: https://lore.kernel.org/r/20220209203411.22332-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
G clock is sourced from PLL3 and PLL6. The output of the mux is
connected to divider.
This patch adds a mux and divider for getting different rates from
this clock sources.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211203115154.31864-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Core clock "I" is sourced from CPG_PL1_DDIV which controls CPU
frequency. Define CPG_PL1_DDIV, so that we can register it as a
clock divider in later patch.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211112081003.15453-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
make W=1:
drivers/clk/renesas/rzg2l-cpg.c:95: warning: Function parameter or member 'num_resets' not described in 'rzg2l_cpg_priv'
Add the missing kerneldoc for fields in struct rzg2l_cpg_priv and struct
rzg2l_cpg_info related to Module Resets.
Fixes: c3e67ad6f5 ("dt-bindings: clock: r9a07g044-cpg: Update clock/reset definitions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/39c2c5fd4232b6620a4a56dba4e2b0d61476ee36.1634646869.git.geert+renesas@glider.be
Add SDHI clk mux support to select SDHI clock from different clock
sources.
As per HW manual, direct clock switching from 533MHz to 400MHz and
vice versa is not recommended. So added support for handling this
in mux.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211007111434.8665-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The AXI and CHI clocks use the same register bit for controlling clock
output. Add a new clock type for coupled clocks, which sets the
CPG_CLKON_ETH.CLK[01]_ON bit when at least one clock is enabled, and
clears the bit only when both clocks are disabled.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922155145.28156-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Ethernet reference clock can be sourced from PLL5_FOUT3 or PLL6. Add
support for ethernet source clock selection using SEL_PLL_6_2 mux.
This patch also renames the PLL5_DIV2 core clock to PLL5_250 to match
with the register description as mentioned in RZ/G2L HW manual (Rev.1.00).
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922155145.28156-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support to handle mux clocks in order to select a clock source
from multiple sources.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922155145.28156-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
