The RZ/{G2L,V2L,G3S} CPG versions support a feature called MSTOP. Each
module has one or more MSTOP bits associated with it, and these bits
need to be configured along with the module clocks. Setting the MSTOP
bits switches the module between normal and standby states.
Previously, MSTOP support was abstracted through power domains (struct
generic_pm_domain::{power_on, power_off} APIs). With this abstraction,
the order of setting the MSTOP and CLKON bits was as follows:
Previous Order:
A/ Switching to Normal State (e.g., during probe):
1/ Clear module MSTOP bit
2/ Set module CLKON bit
B/ Switching to Standby State (e.g., during remove):
1/ Clear CLKON bit
2/ Set MSTOP bit
However, in some cases (when the clock is disabled through devres), the
order may have been (due to the issue described in link section):
1/ Set MSTOP bit
2/ Clear CLKON bit
Recently, the hardware team has suggested that the correct order to set
the MSTOP and CLKON bits is:
Updated Order:
A/ Switching to Normal State (e.g., during probe):
1/ Set CLKON bit
2/ Clear MSTOP bit
B/ Switching to Standby State (e.g., during remove):
1/ Set MSTOP bit
2/ Clear CLKON bit
To prevent future issues due to incorrect ordering, the MSTOP setup has
now been implemented in rzg2l_mod_clock_endisable(), ensuring compliance
with the sequence suggested in Figure 41.5: Module Standby Mode
Procedure from the RZ/G3S HW manual, Rev1.10.
Additionally, since multiple clocks of a single module may be mapped to
a single MSTOP bit, MSTOP setup is reference-counted.
Furthermore, as all modules start in the normal state after reset, if
the module clocks are disabled, the module state is switched to standby.
This prevents keeping the module in an invalid state, as recommended by
the hardware team.
Link: https://lore.kernel.org/all/20250215130849.227812-1-claudiu.beznea.uj@bp.renesas.com/
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250527112403.1254122-5-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Renesas RZ/V2M SoC comes with 6 CSI IPs (CSI0, CSI1, CSI2
CSI3, CSI4, and CSI5), however Linux is only allowed control
of CSI0 and CSI4.
CSI0 shares its reset and PCLK lines with CSI1, CSI2, and CSI3.
CSI4 shares its reset and PCLK lines with CSI5.
This commit adds support for the relevant clocks.
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230622113341.657842-3-fabrizio.castro.jz@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add Compare-Match Timer (TIM) clock and reset entries to CPG
driver.
The TIM IP on the RZ/V2M comes with 32 channels, but the ISP has
full control of channels 0 to 7, and channels 24 to 31. Therefore
Linux is only allowed to use channels 8 to 23.
The TIM has shared peripheral clock with other modules, so mark it
as critical clock.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20221205145955.391526-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add PWM{8..14} clock and reset entries to CPG driver.
The PWM IP on the RZ/V2M comes with 16 channels, but the ISP has
full control of channels 0 to 7, and channel 15, therefore Linux
is only allowed to use channels 8 to 14.
The PWM channel 15 shares apb clock and reset with PWM{8..14}.
The reset is deasserted by the bootloader/ISP.
Add PWM{8..14} clocks to CPG driver and mark apb clock as
critical clock, so that the apb clock will be always on.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20221124191643.3193423-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IIC groups clock and reset entries to CPG driver.
IIC Group A consists of IIC0 and IIC1. IIC Group B consists of
IIC2 and IIC3. To confuse things, IIC_PCLK0 is used by group A
and IIC_PCLK1 is used by group B.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Link: https://lore.kernel.org/r/20220819193944.337599-2-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add ethernet clock/reset entries to CPG driver.
Note that the AXI and CHI clocks are both enabled and disabled using
the same register bit.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220504145454.71287-2-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Renesas RZ/V2M SoC is very similar to RZ/G2L, though it doesn't have
any CLK_MON registers.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-11-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
