The default PLL2/3/4/6 multiplier and divider configurations are no
longer used after the conversion to fixed or variable fractional PLL
clock types.
Note that the default configurations are still documented in the
comments above the individual rcar_gen4_cpg_pll_config instances.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/d13526a86066992d6afdf9bee7c1a18da72f914f.1721648548.git.geert+renesas@glider.be
Currently, all PLLs are modelled as fixed divider clocks, based on the
state of the mode pins. However, the boot loader stack may have changed
the actual PLL configuration from the default, leading to incorrect
clock frequencies.
Describe PLL1 as a fixed fractional PLL instead, and PLL2, PLL3, and
PLL6 as variable fractional PLLs. Note that the R-Car Gen4 clock driver
does not support variable 9.24 PLLs yet, so the driver will downgrade
them to fixed fractional PLLs, too.
Reformat nearby lines to retain a consistent layout.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/8544571f507e00ed6fc61617d27c9e19de5e9d11.1721648548.git.geert+renesas@glider.be
The RSwitch2 and EtherTSN-IF clocks were accidentally mixed up.
While at it, rename them to better match the (future) documentation.
Fixes: a3b4137a4d ("clk: renesas: r8a779f0: Add Ethernet Switch clocks")
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/99b8b41bd2c5043c9e457862ef4bc144869eca58.1668501212.git.geert+renesas@glider.be
As serial communication requires a clean clock signal, the Serial
Communication Interfaces with FIFO (SCIF) are clocked by a clock that is
not affected by Spread Spectrum or Fractional Multiplication.
Hence change the parent clocks for the SCIF modules from the S0D12_PER
clock to the SASYNCPERD4 clock (which has the same clock rate), cfr.
R-Car S4-8 Hardware User's Manual rev. 0.81.
Fixes: 24aaff6a6c ("clk: renesas: cpg-mssr: Add support for R-Car S4-8")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221103143440.46449-3-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As serial communication requires a clean clock signal, the High Speed
Serial Communication Interfaces with FIFO (HSCIF) are clocked by a clock
that is not affected by Spread Spectrum or Fractional Multiplication.
Hence change the parent clocks for the HSCIF modules from the S0D3_PER
clock to the SASYNCPERD1 clock (which has the same clock rate), cfr.
R-Car S4-8 Hardware User's Manual rev. 0.81.
Fixes: 080bcd8d59 ("clk: renesas: r8a779f0: Add HSCIF clocks")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221103143440.46449-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the SASYNCPER internal clock, which is the clock source of the
various SASYNCPERD[124] clocks, to match the clock tree diagram in the
documentation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/18e6765bfc3bf7c3ee5ce93a370d377c1d17728e.1665558014.git.geert+renesas@glider.be
The RPC and RPCD2 core clocks were added to the sections for internal
core clocks, while they are core clock outputs, visible from DT.
Move them to the correct sections.
Rename the ".rpc" clock on R-Car S4 to "rpc".
Fixup nearby whitespace to increase uniformity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/a938b938f00939b9206d7fbaba78e2ef09915f5f.1649681891.git.geert+renesas@glider.be
Add the module clock used by the RCLK Watchdog Timer (RWDT) on the
Renesas R-Car S4-8 (r8a779f0) SoC. Mark it as a critical clock, to
ensure uninterrupted watchdog operation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/8d9b280065a663f2cf31db7b21a010aa781a0af1.1642525158.git.geert+renesas@glider.be
According to Section 8.1.2 Figure 8.1.1 ("Block Diagram of CPG"), Note
22 ("RSW2 divider"), and Table 8.1.4d ("Lists of CPG clocks generated
from CPGMA1"), the RSwitch2 and PCI Express clock is generated from PLL5
by dividing by two, followed by the RSW2 divider. As PLL5 runs at 3200
MHz, and RSW2 is fixed to 320 MHz, the RSW2 divider must be 5.
Correct the parent and the fixed divider.
Fixes: 24aaff6a6c ("clk: renesas: cpg-mssr: Add support for R-Car S4-8")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/d6a406f31e6f02f892e0253f4e8a9a2f68fd652e.1641566003.git.geert+renesas@glider.be
