The alpha PLLs which slew to a new frequency at runtime would require
the PLL to calibrate at the mid point of the VCO. Add the new PLL ops
which can support the slewing of the PLL to a new frequency.
Reviewed-by: Imran Shaik <quic_imrashai@quicinc.com>
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250702-qcs615-mm-v10-clock-controllers-v11-1-9c216e1615ab@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
To properly configure the PLLs on recent chipsets, it often requires more
than one power domain to be kept ON. The support to enable multiple power
domains is being added in qcom_cc_really_probe() and PLLs should be
configured post all the required power domains are enabled.
Hence integrate PLL configuration into clk_alpha_pll structure and add
support for qcom_clk_alpha_pll_configure() function which can be called
from qcom_cc_really_probe() to configure the clock controller PLLs after
all required power domains are enabled.
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Link: https://lore.kernel.org/r/20250530-videocc-pll-multi-pd-voting-v5-4-02303b3a582d@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
If regmap_read() fails, random stack value was used in calculating new
frequency in recalc_rate() callbacks. Such failure is really not
expected as these are all MMIO reads, however code should be here
correct and bail out. This also avoids possible warning on
uninitialized value.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250212-b4-clk-qcom-clean-v3-1-499f37444f5d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add support for Pongo type of PLL clocks, used in Qualcomm SM8750 SoC.
Notable difference comparing to other PLLs is the need for calibration
for internally generated clock followed by wait_for_pll(). This is done
in configure call and at this time clocks are not yet registered, thus
wait_for_pll() cannot use clk_hw_get_name. Locking during this
calibration requires much more time, thus increase the timeout in
wait_for_pll().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250106-sm8750-dispcc-v2-2-6f42beda6317@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Commit c45ae598fc ("clk: qcom: support for alpha mode configuration")
added support for configuring alpha mode, but it seems that the feature
was never working in practice.
The value of the alpha_{en,mode}_mask members of the configuration gets
added to the value parameter passed to the regmap_update_bits() function,
however the same values are not getting applied to the bitmask. As the
result, the respective bits in the USER_CTL register are never modifed
which leads to improper configuration of several PLLs.
The following table shows the PLL configurations where the 'alpha_en_mask'
member is set and which are passed as a parameter for the
clk_alpha_pll_configure() function. In the table the 'expected rate' column
shows the rate the PLL should run at with the given configuration, and
the 'real rate' column shows the rate the PLL runs at actually. The real
rates has been verified on hardwareOn IPQ* platforms, on other platforms,
those are computed values only.
file pll expected rate real rate
dispcc-qcm2290.c disp_cc_pll0 768.0 MHz 768.0 MHz
dispcc-sm6115.c disp_cc_pll0 768.0 MHz 768.0 MHz
gcc-ipq5018.c ubi32_pll 1000.0 MHz != 984.0 MHz
gcc-ipq6018.c nss_crypto_pll 1200.0 MHz 1200.0 MHz
gcc-ipq6018.c ubi32_pll 1497.6 MHz != 1488.0 MHz
gcc-ipq8074.c nss_crypto_pll 1200.0 MHz != 1190.4 MHz
gcc-qcm2290.c gpll11 532.0 MHz != 518.4 MHz
gcc-qcm2290.c gpll8 533.2 MHz != 518.4 MHz
gcc-qcs404.c gpll3 921.6 MHz 921.6 MHz
gcc-sm6115.c gpll11 600.0 MHz != 595.2 MHz
gcc-sm6115.c gpll8 800.0 MHz != 787.2 MHz
gpucc-sdm660.c gpu_cc_pll0 800.0 MHz != 787.2 MHz
gpucc-sdm660.c gpu_cc_pll1 740.0 MHz != 729.6 MHz
gpucc-sm6115.c gpu_cc_pll0 1200.0 MHz != 1190.4 MHz
gpucc-sm6115.c gpu_cc_pll1 640.0 MHz != 633.6 MHz
gpucc-sm6125.c gpu_pll0 1020.0 MHz != 1017.6 MHz
gpucc-sm6125.c gpu_pll1 930.0 MHz != 921.6 MHz
mmcc-sdm660.c mmpll8 930.0 MHz != 921.6 MHz
mmcc-sdm660.c mmpll5 825.0 MHz != 806.4 MHz
As it can be seen from the above, there are several PLLs which are
configured incorrectly.
Change the code to apply both 'alpha_en_mask' and 'alpha_mode_mask'
values to the bitmask in order to configure the alpha mode correctly.
Applying the 'alpha_en_mask' fixes the initial rate of the PLLs showed
in the table above. Since the 'alpha_mode_mask' is not used by any driver
currently, that part of the change causes no functional changes.
Cc: stable@vger.kernel.org
Fixes: c45ae598fc ("clk: qcom: support for alpha mode configuration")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://lore.kernel.org/r/20241021-fix-alpha-mode-config-v1-1-f32c254e02bc@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
some unit tests for the assigned clk rates feature in DeviceTree. On the vendor
driver side, we gained a whole pile of SoC driver support detailed below. The
majority in the diffstat is Qualcomm, but there's also quite a few Samsung and
Mediatek clk driver additions in here as well. The top vendors is quite common,
but the sheer amount of new drivers is uncommon, so I'm anticipating a larger
number of fixes for clk drivers this cycle.
Core:
- devm_clk_bulk_get_all_enabled() to return number of clks acquired
- devm_clk_hw_register_gate_parent_hw() helper to modernize drivers
- KUnit tests for clk-assigned-rates{,-u64}
New Drivers:
- Marvell PXA1908 SoC clks
- Mobileye EyeQ5, EyeQ6L and EyeQ6H clk driver
- TWL6030 clk driver
- Nuvoton Arbel BMC NPCM8XX SoC clks
- MediaTek MT6735 SoC clks
- MediaTek MT7620, MT7628 and MT7688 MMC clks
- Add a driver for gated fixed rate clocks
- Global clock controllers for Qualcomm QCS8300 and IPQ5424 SoCs
- Camera, display and video clock controllers for Qualcomm SA8775P SoCs
- Global, display, GPU, TCSR, and RPMh clock controllers for Qualcomm SAR2130P
- Global, camera, display, GPU, and video clock controllers for Qualcomm
SM8475 SoCs
- RTC power domain and Battery Backup Function (VBATTB) clock support for the
Renesas RZ/G3S SoC
- Qualcomm IPQ9574 alpha PLLs
- Support for i.MX91 CCM in the i.MX93 driver
- Microchip LAN969X SoC clks
- Cortex-A55 core clocks and Interrupt Control Unit (ICU) clock and reset on
Renesas RZ/V2H(P)
- Samsung ExynosAutov920 clk drivers for PERIC1, MISC, HSI0 and HSI1
- Samsung Exynos8895 clk drivers for FSYS0/1, PERIC0/1, PERIS and TOP
Updates:
- Convert more clk bindings to YAML
- Various clk driver cleanups: NULL checks, add const, etc.
- Remove END/NUM #defines that count number of clks in various binding headers
- Continue moving reset drivers to drivers/reset via auxiliary bus
-----BEGIN PGP SIGNATURE-----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=FqLm
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The core framework gained a clk provider helper, a clk consumer
helper, and some unit tests for the assigned clk rates feature in
DeviceTree. On the vendor driver side, we gained a whole pile of SoC
driver support detailed below. The majority in the diffstat is
Qualcomm, but there's also quite a few Samsung and Mediatek clk driver
additions in here as well. The top vendors is quite common, but the
sheer amount of new drivers is uncommon, so I'm anticipating a larger
number of fixes for clk drivers this cycle.
Core:
- devm_clk_bulk_get_all_enabled() to return number of clks acquired
- devm_clk_hw_register_gate_parent_hw() helper to modernize drivers
- KUnit tests for clk-assigned-rates{,-u64}
New Drivers:
- Marvell PXA1908 SoC clks
- Mobileye EyeQ5, EyeQ6L and EyeQ6H clk driver
- TWL6030 clk driver
- Nuvoton Arbel BMC NPCM8XX SoC clks
- MediaTek MT6735 SoC clks
- MediaTek MT7620, MT7628 and MT7688 MMC clks
- Add a driver for gated fixed rate clocks
- Global clock controllers for Qualcomm QCS8300 and IPQ5424 SoCs
- Camera, display and video clock controllers for Qualcomm SA8775P
SoCs
- Global, display, GPU, TCSR, and RPMh clock controllers for Qualcomm
SAR2130P
- Global, camera, display, GPU, and video clock controllers for
Qualcomm SM8475 SoCs
- RTC power domain and Battery Backup Function (VBATTB) clock support
for the Renesas RZ/G3S SoC
- Qualcomm IPQ9574 alpha PLLs
- Support for i.MX91 CCM in the i.MX93 driver
- Microchip LAN969X SoC clks
- Cortex-A55 core clocks and Interrupt Control Unit (ICU) clock and
reset on Renesas RZ/V2H(P)
- Samsung ExynosAutov920 clk drivers for PERIC1, MISC, HSI0 and HSI1
- Samsung Exynos8895 clk drivers for FSYS0/1, PERIC0/1, PERIS and TOP
Updates:
- Convert more clk bindings to YAML
- Various clk driver cleanups: NULL checks, add const, etc.
- Remove END/NUM #defines that count number of clks in various
binding headers
- Continue moving reset drivers to drivers/reset via auxiliary bus"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (162 commits)
clk: clk-loongson2: Fix potential buffer overflow in flexible-array member access
clk: Fix invalid execution of clk_set_rate
clk: clk-loongson2: Fix memory corruption bug in struct loongson2_clk_provider
clk: lan966x: make it selectable for ARCH_LAN969X
clk: eyeq: add EyeQ6H west fixed factor clocks
clk: eyeq: add EyeQ6H central fixed factor clocks
clk: eyeq: add EyeQ5 fixed factor clocks
clk: eyeq: add fixed factor clocks infrastructure
clk: eyeq: require clock index with phandle in all cases
clk: fixed-factor: add clk_hw_register_fixed_factor_index() function
dt-bindings: clock: eyeq: add more Mobileye EyeQ5/EyeQ6H clocks
dt-bindings: soc: mobileye: set `#clock-cells = <1>` for all compatibles
clk: clk-axi-clkgen: make sure to enable the AXI bus clock
dt-bindings: clock: axi-clkgen: include AXI clk
clk: mmp: Add Marvell PXA1908 MPMU driver
clk: mmp: Add Marvell PXA1908 APMU driver
clk: mmp: Add Marvell PXA1908 APBCP driver
clk: mmp: Add Marvell PXA1908 APBC driver
dt-bindings: clock: Add Marvell PXA1908 clock bindings
clk: mmp: Switch to use struct u32_fract instead of custom one
...
Add support for NSS Huayra alpha pll found on ipq9574 SoCs.
Programming sequence is the same as that of Huayra type Alpha PLL,
so we can re-use the same.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
Link: https://lore.kernel.org/r/20241028060506.246606-2-quic_srichara@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The lucid 5lpe PLL enable check only checks for an impossible negative
return value and does not actually return as intended in case the PLL is
already enabled (e.g. has been left enabled by boot firmware).
Fixes: f4c7e27aa4 ("clk: qcom: clk-alpha-pll: Add support for Lucid 5LPE PLL")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241022080521.359-3-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The boot firmware may have left the display enabled and its PLL running,
which currently generates a warning on boot (e.g. on x1e80100):
disp_cc_pll0 PLL is already enabled
Drop the bogus warning and fix up the PLL enabled error handling
(trion_pll_is_enabled() only returns 0 or 1).
Fixes: d1b121d62b ("clk: qcom: Add LUCID_EVO PLL type for SDX65")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241022080521.359-2-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Many qcom clock drivers do not have .width set. In that case value of
(p)->width - 1 will be negative which breaks clock tree. Fix this
by checking if width is zero, and pass 3 to GENMASK if that's the case.
Fixes: 1c3541145c ("clk: qcom: support for 2 bit PLL post divider")
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Christopher Obbard <christopher.obbard@linaro.org>
Tested-by: Christopher Obbard <christopher.obbard@linaro.org>
Link: https://lore.kernel.org/r/20241006-fix-postdiv-mask-v3-1-160354980433@mainlining.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
support for the newly ratified DT property 'assigned-clock-rates-u64'. I'm much
more excited about the support for loading DT overlays from KUnit tests so that
we can test how the clk framework parses DT nodes during clk registration. The
clk framework has some places that are highly DeviceTree dependent so this
charts the path to extend the KUnit tests to cover even more framework code in
the future. I've got some more tests on the list that use the DT overlay
support, but they uncovered issues with clk unregistration that I'm still
working on fixing.
Outside the core, the clk driver update pile is dominated by Qualcomm and
Renesas SoCs, making it fairly usual. Looking closer, there are fixes for
things all over the place, like adding missing clk frequencies or moving
defines for the number of clks out of DT binding headers into the drivers.
There are even conversions of DT bindings to YAML and migration away from
strings to describe clk topology. Overall it doesn't look unusual so I expect
the new drivers to be where we'll have fixes in the coming weeks.
Core:
- KUnit tests for clk registration and fixed rate basic clk type
- A couple more devm helpers, one consumer and one provider
- Support for assigned-clock-rates-u64
New Drivers:
- Camera, display and GPU clocks on Qualcomm SM4450
- Camera clocks on Qualcomm SM8150
- Rockchip rk3576 clks
- Microchip SAM9X7 clks
- Renesas RZ/V2H(P) (R9A09G057) clks
Updates:
- Mark a bunch of struct freq_tbl const to reduce .data usage
- Add Qualcomm MSM8226 A7PLL and Regera PLL support
- Fix the Qualcomm Lucid 5LPE PLL configuration sequence to not reuse
Trion, as they do differ
- A number of fixes to the Qualcomm SM8550 display clock driver
- Fold Qualcomm SM8650 display clock driver into SM8550 one
- Add missing clocks and GDSCs needed for audio on Qualcomm MSM8998
- Add missing USB MP resets, GPLL9, and QUPv3 DFS to Qualcomm SC8180X
- Fix sdcc clk frequency tables on Qualcomm SC8180X
- Drop the Qualcomm SM8150 gcc_cpuss_ahb_clk_src
- Mark Qualcomm PCIe GDSCs as RET_ON on sm8250 and sm8540 to avoid them
turning off during suspend
- Use the HW_CTRL mechanism on Qualcomm SM8550 video clock controller
GDSCs
- Get rid of CLK_NR_CLKS defines in Rockchip DT binding headers
- Some fixes for Rockchip rk3228 and rk3588
- Exynos850: Add clock for Thermal Management Unit
- Exynos7885: Fix duplicated ID in the header, add missing TOP PLLs and
add clocks for USB block in the FSYS clock controller
- ExynosAutov9: Add DPUM clock controller
- ExynosAutov920: Add new (first) clock controllers: TOP and PERIC0
(and a bit more complete bindings)
- Use clk_hw pointer instead of fw_name for acm_aud_clk[0-1]_sel clocks
on i.MX8Q as parents in ACM provider
- Add i.MX95 NETCMIX support to the block control provider
- Fix parents for ENETx_REF_SEL clocks on i.MX6UL
- Add USB clocks, resets and power domains on Renesas RZ/G3S
- Add Generic Timer (GTM), I2C Bus Interface (RIIC), SD/MMC Host
Interface (SDHI) and Watchdog Timer (WDT) clocks and resets on
Renesas RZ/V2H
- Add PCIe, PWM, and CAN-FD clocks on Renesas R-Car V4M
- Add LCD controller clocks and resets on Renesas RZ/G2UL
- Add DMA clocks and resets on Renesas RZ/G3S
- Add fractional multiplication PLL support on Renesas R-Car Gen4
- Document support for the Renesas RZ/G2M v3.0 (r8a774a3) SoC
- Support for the Microchip SAM9X7 SoC as follows:
- Updates for the Microchip PLL drivers
- DT binding documentation updates (for the new clock driver and for
the slow clock controller that SAM9X7 is using)
- A fix for the Microchip SAMA7G5 clock driver to avoid allocating more
memory than necessary
- Constify some Amlogic structs
- Add SM1 eARC clocks for Amlogic
- Introduce a symbol namespace for Amlogic clock specific symbols
- Add reset controller support to audiomix block control on i.MX
- Add CLK_SET_RATE_PARENT flag to all audiomix clocks and to
i.MX7D lcdif_pixel_src clock
- Fix parent clocks for earc_phy and audpll on i.MX8MP
- Fix default parents for enet[12]_ref_sel on i.MX6UL
- Add ops in composite 8M and 93 that allow no-op on disable
- Add check for PCC present bit on composite 7ULP register
- Fix fractional part for fracn-gppll on prepare in i.MX
- Fix clock tree update for TF-A managed clocks on i.MX8M
- Drop CLK_SET_PARENT_GATE for DRAM mux on i.MX7D
- Add the SAI7 IPG clock for i.MX8MN
- Mark the 'nand_usdhc_bus' clock as non-critical on i.MX8MM
- Add LVDS bypass clocks on i.MX8QXP
- Add muxes for MIPI and PHY ref clocks on i.MX
- Reorder dc0_bypass0_clk, lcd_pxl and dc1_disp clocks on i.MX8QXP
- Add 1039.5MHz and 800MHz rates to fracn-gppll table on i.MX
- Add CLK_SET_RATE_PARENT for media_disp pixel clocks on i.MX8QXP
- Add some module descriptions to the i.MX generic and the
i.MXRT1050 driver
- Fix return value for bypass for composite i.MX7ULP
- Move Mediatek clk bindings to clock/
- Convert some more clk bindings to dt schema
-----BEGIN PGP SIGNATURE-----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=XmiQ
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The core clk framework is left largely untouched this time around
except for support for the newly ratified DT property
'assigned-clock-rates-u64'.
I'm much more excited about the support for loading DT overlays from
KUnit tests so that we can test how the clk framework parses DT nodes
during clk registration. The clk framework has some places that are
highly DeviceTree dependent so this charts the path to extend the
KUnit tests to cover even more framework code in the future. I've got
some more tests on the list that use the DT overlay support, but they
uncovered issues with clk unregistration that I'm still working on
fixing.
Outside the core, the clk driver update pile is dominated by Qualcomm
and Renesas SoCs, making it fairly usual. Looking closer, there are
fixes for things all over the place, like adding missing clk
frequencies or moving defines for the number of clks out of DT binding
headers into the drivers. There are even conversions of DT bindings to
YAML and migration away from strings to describe clk topology. Overall
it doesn't look unusual so I expect the new drivers to be where we'll
have fixes in the coming weeks.
Core:
- KUnit tests for clk registration and fixed rate basic clk type
- A couple more devm helpers, one consumer and one provider
- Support for assigned-clock-rates-u64
New Drivers:
- Camera, display and GPU clocks on Qualcomm SM4450
- Camera clocks on Qualcomm SM8150
- Rockchip rk3576 clks
- Microchip SAM9X7 clks
- Renesas RZ/V2H(P) (R9A09G057) clks
Updates:
- Mark a bunch of struct freq_tbl const to reduce .data usage
- Add Qualcomm MSM8226 A7PLL and Regera PLL support
- Fix the Qualcomm Lucid 5LPE PLL configuration sequence to not reuse
Trion, as they do differ
- A number of fixes to the Qualcomm SM8550 display clock driver
- Fold Qualcomm SM8650 display clock driver into SM8550 one
- Add missing clocks and GDSCs needed for audio on Qualcomm MSM8998
- Add missing USB MP resets, GPLL9, and QUPv3 DFS to Qualcomm SC8180X
- Fix sdcc clk frequency tables on Qualcomm SC8180X
- Drop the Qualcomm SM8150 gcc_cpuss_ahb_clk_src
- Mark Qualcomm PCIe GDSCs as RET_ON on sm8250 and sm8540 to avoid
them turning off during suspend
- Use the HW_CTRL mechanism on Qualcomm SM8550 video clock controller
GDSCs
- Get rid of CLK_NR_CLKS defines in Rockchip DT binding headers
- Some fixes for Rockchip rk3228 and rk3588
- Exynos850: Add clock for Thermal Management Unit
- Exynos7885: Fix duplicated ID in the header, add missing TOP PLLs
and add clocks for USB block in the FSYS clock controller
- ExynosAutov9: Add DPUM clock controller
- ExynosAutov920: Add new (first) clock controllers: TOP and PERIC0
(and a bit more complete bindings)
- Use clk_hw pointer instead of fw_name for acm_aud_clk[0-1]_sel
clocks on i.MX8Q as parents in ACM provider
- Add i.MX95 NETCMIX support to the block control provider
- Fix parents for ENETx_REF_SEL clocks on i.MX6UL
- Add USB clocks, resets and power domains on Renesas RZ/G3S
- Add Generic Timer (GTM), I2C Bus Interface (RIIC), SD/MMC Host
Interface (SDHI) and Watchdog Timer (WDT) clocks and resets on
Renesas RZ/V2H
- Add PCIe, PWM, and CAN-FD clocks on Renesas R-Car V4M
- Add LCD controller clocks and resets on Renesas RZ/G2UL
- Add DMA clocks and resets on Renesas RZ/G3S
- Add fractional multiplication PLL support on Renesas R-Car Gen4
- Document support for the Renesas RZ/G2M v3.0 (r8a774a3) SoC
- Support for the Microchip SAM9X7 SoC as follows:
- Updates for the Microchip PLL drivers
- DT binding documentation updates (for the new clock driver and for
the slow clock controller that SAM9X7 is using)
- A fix for the Microchip SAMA7G5 clock driver to avoid allocating
more memory than necessary
- Constify some Amlogic structs
- Add SM1 eARC clocks for Amlogic
- Introduce a symbol namespace for Amlogic clock specific symbols
- Add reset controller support to audiomix block control on i.MX
- Add CLK_SET_RATE_PARENT flag to all audiomix clocks and to i.MX7D
lcdif_pixel_src clock
- Fix parent clocks for earc_phy and audpll on i.MX8MP
- Fix default parents for enet[12]_ref_sel on i.MX6UL
- Add ops in composite 8M and 93 that allow no-op on disable
- Add check for PCC present bit on composite 7ULP register
- Fix fractional part for fracn-gppll on prepare in i.MX
- Fix clock tree update for TF-A managed clocks on i.MX8M
- Drop CLK_SET_PARENT_GATE for DRAM mux on i.MX7D
- Add the SAI7 IPG clock for i.MX8MN
- Mark the 'nand_usdhc_bus' clock as non-critical on i.MX8MM
- Add LVDS bypass clocks on i.MX8QXP
- Add muxes for MIPI and PHY ref clocks on i.MX
- Reorder dc0_bypass0_clk, lcd_pxl and dc1_disp clocks on i.MX8QXP
- Add 1039.5MHz and 800MHz rates to fracn-gppll table on i.MX
- Add CLK_SET_RATE_PARENT for media_disp pixel clocks on i.MX8QXP
- Add some module descriptions to the i.MX generic and the i.MXRT1050
driver
- Fix return value for bypass for composite i.MX7ULP
- Move Mediatek clk bindings to clock/
- Convert some more clk bindings to dt schema"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (180 commits)
clk: Switch back to struct platform_driver::remove()
dt-bindings: clock, reset: fix top-comment indentation rk3576 headers
clk: rockchip: remove unused mclk_pdm0_p/pdm0_p definitions
clk: provide devm_clk_get_optional_enabled_with_rate()
clk: fixed-rate: add devm_clk_hw_register_fixed_rate_parent_data()
clk: imx6ul: fix clock parent for IMX6UL_CLK_ENETx_REF_SEL
clk: renesas: r9a09g057: Add clock and reset entries for GTM/RIIC/SDHI/WDT
clk: renesas: rzv2h: Add support for dynamic switching divider clocks
clk: renesas: r9a08g045: Add clocks, resets and power domains for USB
clk: rockchip: fix error for unknown clocks
clk: rockchip: rk3588: drop unused code
clk: rockchip: Add clock controller for the RK3576
clk: rockchip: Add new pll type pll_rk3588_ddr
dt-bindings: clock, reset: Add support for rk3576
dt-bindings: clock: rockchip,rk3588-cru: drop unneeded assigned-clocks
clk: rockchip: rk3588: Fix 32k clock name for pmu_24m_32k_100m_src_p
clk: imx95: enable the clock of NETCMIX block control
dt-bindings: clock: add RMII clock selection
dt-bindings: clock: add i.MX95 NETCMIX block control
clk: imx: imx8: Use clk_hw pointer for self registered clock in clk_parent_data
...
According to msm-5.10 the lucid 5lpe PLLs have require slightly
different configuration that trion / lucid PLLs, it doesn't set
PLL_UPDATE_BYPASS bit. Add corresponding function and use it for the
display clock controller on Qualcomm SM8350 platform.
Fixes: 205737fe33 ("clk: qcom: add support for SM8350 DISPCC")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240804-sm8350-fixes-v1-2-1149dd8399fe@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
In LUCID EVO PLL CAL_L_VAL and L_VAL bitfields are part of single
PLL_L_VAL register. Update for L_VAL bitfield values in PLL_L_VAL
register using regmap_write() API in __alpha_pll_trion_set_rate
callback will override LUCID EVO PLL initial configuration related
to PLL_CAL_L_VAL bit fields in PLL_L_VAL register.
Observed random PLL lock failures during PLL enable due to such
override in PLL calibration value. Use regmap_update_bits() with
L_VAL bitfield mask instead of regmap_write() API to update only
PLL_L_VAL bitfields in __alpha_pll_trion_set_rate callback.
Fixes: 260e36606a ("clk: qcom: clk-alpha-pll: add Lucid EVO PLL configuration interfaces")
Cc: stable@vger.kernel.org
Signed-off-by: Ajit Pandey <quic_ajipan@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20240611133752.2192401-2-quic_ajipan@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The Zonda PLL has a 16 bit signed alpha and in the cases where the alpha
value is greater than 0.5, the L value needs to be adjusted accordingly.
Thus update the logic to handle the signed alpha val.
Fixes: f21b6bfecc ("clk: qcom: clk-alpha-pll: add support for zonda pll")
Cc: stable@vger.kernel.org
Signed-off-by: Satya Priya Kakitapalli <quic_skakitap@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240731062916.2680823-5-quic_skakitap@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Currently, clk_zonda_pll_set_rate polls for the PLL to lock even if the
PLL is disabled. However, if the PLL is disabled then LOCK_DET will
never assert and we'll return an error. There is no reason to poll
LOCK_DET if the PLL is already disabled, so skip polling in this case.
Fixes: f21b6bfecc ("clk: qcom: clk-alpha-pll: add support for zonda pll")
Cc: stable@vger.kernel.org
Signed-off-by: Satya Priya Kakitapalli <quic_skakitap@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240731062916.2680823-4-quic_skakitap@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Correct the pll postdiv shift used in clk_trion_pll_postdiv_set_rate
API. The shift value is not same for different types of plls and
should be taken from the pll's .post_div_shift member.
Fixes: 548a909597 ("clk: qcom: clk-alpha-pll: Add support for Trion PLLs")
Cc: stable@vger.kernel.org
Signed-off-by: Satya Priya Kakitapalli <quic_skakitap@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240731062916.2680823-3-quic_skakitap@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
clk driver support. We have the usual Qualcomm clk drivers, along with
clk drivers for the Sophgo and T-Head vendors, all to support some new
SoCs.
Nothing in particular stands out to me in the updates. There's the
interconnect clk driver which exposes clks as interconnects, crossing
subsystems. There's a bunch of janitorial things that are improving
drivers in general like kmemdup_array() or fixing error paths. But
overall the updates look normal to fix the description data which is
usually the stuff that's wrong and/or untested.
I really wanted to land a bunch of KUnit clk code that I've been working
on whenever I get some free time but it turned into a pumpkin at the
last minute so I dropped those patches. I'll let it soak in linux-next
after the merge window closes. I have a suspicion that we're going to
need to totally rework the clk framework to fix structural issues like
locking, clk rate setting, and runtime PM usage. Having a bunch of unit
tests for that will help make sure that all keeps working.
Core:
- Skip gate basic type KUnit tests on s390 due to lack of MMIO emulation
New Drivers:
- AP sub-system clock controller in the T-Head TH1520
- Sophgo Sophon sg2042 clk driver
- Qualcomm SM7150 camera, display and video clk drivers
- Qualcomm QCM2290 GPU clk driver
- Qualcomm QCS8386/QCS8084 NSS clk driver
- Qualcomm SM8650 camera and video drivers
Updates:
- Add reset support to Airoha EN7581 clk driver
- Add MODULE_DESCRIPTIONs to various clk drivers
- Introduce helper logic to expose clock controllers as simple
interconnect providers
- Use the interconnect helper above on Qualcomm ipq9574
- Add CLK_SET_RATE_PARENT to the remaining USB pipe clocks on Qualcomm
X1Elite
- Improve error handling in Qualcomm kpss-xcc driver
- Mark Qualcomm SC8280XP LPASS clock controller regmap_config const
- Export more clocks for Rockchip rk3128 peripherals
- Convert Rockchip clk drivers to use kmemdup_array()
- Drop CLK_NR_CLKS from Rockchip rk3128 and rk3188 binding headers
- Make qcom_cc_really_probe() take a struct device to allow reuse in
non-platform-drivers
- Introduce prepare-only branch clock ops in the qcom clk driver to
support clocks on buses that take locks
- Describe parent/child relationship for Qualcomm SC7280 camera GDSCs
- Support Qualcomm Huayra 2290 alpha PLL
- Adjust the highest SDCC clock frequency on Qualcomm IPQ6018 to match
HS200 support
- Add missing PCIe PIPE clocks on Qualcomm IPQ9574
- Fix various configurations and properties in the Qualcomm SA8775P,
X1E80100 and SM7280 drivers
- Park Qualcomm SM8350 GPU RCGs on XO while disabled
- Remove unused CONFIG_QCOM_RPMCC Kconfig symbol
- exynos-clkout: Remove usage of of_device_id table as .of_match_table,
because the driver is instantiated as MFD cell, not as standalone platform
driver. Populated .of_match_table confused people few times to convert the
code to device_get_match_data(), which broke the driver
- Mark one Samsung UFS clock as critical, because having it off stops the
system from shutdown
- Use kmemdup_array() when applicable
- Remove unused 'struct gates_data' from old sunxi driver library
- Add GPADC clock and reset for Allwinner H616
- Minor Amlogic S4 clock fixes
- DT bindings Yaml conversion of the Amlogic AXG audio controller
- Amlogic C3 clock controllers support
- Amlogic clk flag added to skip init of already enabled PLLs and avoid relocking
- Amlogic A1 DT bindings updates for system pll support
- Add missing MODULE_DESCRIPTION where necessary
- Remove obsolete clock DT binding header files
- Add Battery Backup (VBATTB) and I2C clocks, resets, and power
domains on Renesas RZ/G3S
- Add audio clocks on Renesas R-Car V4M
- Add video capture (ISPCS, CSI-2, VIN) clocks on Renesas R-Car V4M
-----BEGIN PGP SIGNATURE-----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=jEjn
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This a large collection of clk driver updates and a handful of new SoC
clk driver support.
We have the usual Qualcomm clk drivers, along with clk drivers for the
Sophgo and T-Head vendors, all to support some new SoCs.
Nothing in particular stands out to me in the updates. There's the
interconnect clk driver which exposes clks as interconnects, crossing
subsystems. There's a bunch of janitorial things that are improving
drivers in general like kmemdup_array() or fixing error paths. But
overall the updates look normal to fix the description data which is
usually the stuff that's wrong and/or untested.
Core:
- Skip gate basic type KUnit tests on s390 due to lack of MMIO
emulation
New Drivers:
- AP sub-system clock controller in the T-Head TH1520
- Sophgo Sophon sg2042 clk driver
- Qualcomm SM7150 camera, display and video clk drivers
- Qualcomm QCM2290 GPU clk driver
- Qualcomm QCS8386/QCS8084 NSS clk driver
- Qualcomm SM8650 camera and video drivers
Updates:
- Add reset support to Airoha EN7581 clk driver
- Add MODULE_DESCRIPTIONs to various clk drivers
- Introduce helper logic to expose clock controllers as simple
interconnect providers
- Use the interconnect helper above on Qualcomm ipq9574
- Add CLK_SET_RATE_PARENT to the remaining USB pipe clocks on
Qualcomm X1Elite
- Improve error handling in Qualcomm kpss-xcc driver
- Mark Qualcomm SC8280XP LPASS clock controller regmap_config const
- Export more clocks for Rockchip rk3128 peripherals
- Convert Rockchip clk drivers to use kmemdup_array()
- Drop CLK_NR_CLKS from Rockchip rk3128 and rk3188 binding headers
- Make qcom_cc_really_probe() take a struct device to allow reuse in
non-platform-drivers
- Introduce prepare-only branch clock ops in the qcom clk driver to
support clocks on buses that take locks
- Describe parent/child relationship for Qualcomm SC7280 camera GDSCs
- Support Qualcomm Huayra 2290 alpha PLL
- Adjust the highest SDCC clock frequency on Qualcomm IPQ6018 to
match HS200 support
- Add missing PCIe PIPE clocks on Qualcomm IPQ9574
- Fix various configurations and properties in the Qualcomm SA8775P,
X1E80100 and SM7280 drivers
- Park Qualcomm SM8350 GPU RCGs on XO while disabled
- Remove unused CONFIG_QCOM_RPMCC Kconfig symbol
- exynos-clkout: Remove usage of of_device_id table as
.of_match_table, because the driver is instantiated as MFD cell,
not as standalone platform driver. Populated .of_match_table
confused people few times to convert the code to
device_get_match_data(), which broke the driver
- Mark one Samsung UFS clock as critical, because having it off stops
the system from shutdown
- Use kmemdup_array() when applicable
- Remove unused 'struct gates_data' from old sunxi driver library
- Add GPADC clock and reset for Allwinner H616
- Minor Amlogic S4 clock fixes
- DT bindings Yaml conversion of the Amlogic AXG audio controller
- Amlogic C3 clock controllers support
- Amlogic clk flag added to skip init of already enabled PLLs and
avoid relocking
- Amlogic A1 DT bindings updates for system pll support
- Add missing MODULE_DESCRIPTION where necessary
- Remove obsolete clock DT binding header files
- Add Battery Backup (VBATTB) and I2C clocks, resets, and power
domains on Renesas RZ/G3S
- Add audio clocks on Renesas R-Car V4M
- Add video capture (ISPCS, CSI-2, VIN) clocks on Renesas R-Car V4M"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (135 commits)
clk: thead: Add support for T-Head TH1520 AP_SUBSYS clocks
dt-bindings: clock: Document T-Head TH1520 AP_SUBSYS controller
clk: sophgo: Avoid -Wsometimes-uninitialized in sg2042_clk_pll_set_rate()
clk/sophgo: Using BUG() instead of unreachable() in mmux_get_parent_id()
clk: mxs: Use clamp() in clk_ref_round_rate() and clk_ref_set_rate()
clk: sunxi-ng r40: Constify struct regmap_config
clk: en7523: fix rate divider for slic and spi clocks
clk: lpc32xx: Constify struct regmap_config
clk: xilinx: Constify struct regmap_config
clk: en7523: Remove PCIe reset open drain configuration for EN7581
clk: en7523: Remove pcie prepare/unpreare callbacks for EN7581 SoC
clk: en7523: Add reset-controller support for EN7581 SoC
dt-bindings: clock: airoha: Add reset support to EN7581 clock binding
dt-bindings: clock: mediatek: Document reset cells for MT8188 sys
clk: mediatek: mt8173-infracfg: Handle unallocated infracfg when module
dt-bindings: clock: mediatek: add syscon compatible for mt7622 pciesys
dt-bindings: clock: sprd,sc9860-clk: convert to YAML
dt-bindings: clock: qoriq-clock: convert to yaml format
clk: qcom: Park shared RCGs upon registration
clk: qcom: ipq9574: Use icc-clk for enabling NoC related clocks
...
Commit 134b55b7e1 ("clk: qcom: support Huayra type Alpha PLL")
introduced an entry to the alpha offsets array, but diving into QCM2290
downstream and some documentation, it turned out that the name Huayra
apparently has been used quite liberally across many chips, even with
noticeably different hardware.
Introduce another set of offsets and a new configure function for the
Huayra PLL found on QCM2290. This is required e.g. for the consumers
of GPUCC_PLL0 to properly start.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240606-topic-rb1_gpu-v4-2-4bc0c19da4af@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The clk_alpha_pll_stromer_plus_set_rate() function does not
sets the ALPHA_EN bit in the USER_CTL register, so setting
rates which requires using alpha mode works only if the bit
gets set already prior calling the function.
Extend the function to set the ALPHA_EN bit in order to allow
using fractional rates regardless whether the bit gets set
previously or not.
Fixes: 84da48921a ("clk: qcom: clk-alpha-pll: introduce stromer plus ops")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://lore.kernel.org/r/20240508-stromer-plus-alpha-en-v1-1-6639ce01ca5b@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The clk_alpha_pll_stromer_set_rate() function writes inproper
values into the ALPHA_VAL{,_U} registers which results in wrong
clock rates when the alpha value is used.
The broken behaviour can be seen on IPQ5018 for example, when
dynamic scaling sets the CPU frequency to 800000 KHz. In this
case the CPU cores are running only at 792031 KHz:
# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq
800000
# cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq
792031
This happens because the function ignores the fact that the alpha
value calculated by the alpha_pll_round_rate() function is only
32 bits wide which must be extended to 40 bits if it is used on
a hardware which supports 40 bits wide values.
Extend the clk_alpha_pll_stromer_set_rate() function to convert
the alpha value to 40 bits before wrinting that into the registers
in order to ensure that the hardware really uses the requested rate.
After the change the CPU frequency is correct:
# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq
800000
# cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq
800000
Cc: stable@vger.kernel.org
Fixes: e47a4f55f2 ("clk: qcom: clk-alpha-pll: Add support for Stromer PLLs")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://lore.kernel.org/r/20240328-alpha-pll-fix-stromer-set-rate-v3-1-1b79714c78bc@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Move the locally defined Huayra register map to 'clk_alpha_pll_regs'
in order to allow using that by other drivers, like the clk-cbf-8996.
No functional changes.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://lore.kernel.org/r/20240328-apss-ipq-pll-cleanup-v4-2-eddbf617f0c8@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The register offset arrays are ordered based on the register
offsets for all PLLs but the Stromer. For consistency, reorder
the Stromer specific array as well.
No functional changes.
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240311-alpha-pll-stromer-cleanup-v1-2-f7c0c5607cca@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The offset of the CONFIG_CTL_U register defined for the Stromer
PLL is wrong. It is not aligned on a 4 bytes boundary which might
causes errors in regmap operations.
Maybe the intention behind of using the 0xff value was to indicate
that the register is not implemented in the PLL, but this is not
verified anywhere in the code. Moreover, this value is not used
even in other register offset arrays despite that those PLLs also
have unimplemented registers.
Additionally, on the Stromer PLLs the current code only touches
the CONFIG_CTL_U register if the result of pll_has_64bit_config()
is true which condition is not affected by the change.
Due to the reasons above, simply remove the CONFIG_CTL_U entry
from the Stromer specific array.
Fixes: e47a4f55f2 ("clk: qcom: clk-alpha-pll: Add support for Stromer PLLs")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240311-alpha-pll-stromer-cleanup-v1-1-f7c0c5607cca@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The PLL0 is configured by the bootloader and is the parent of the
mdp_clk_src. The Trion implementation of the configure function is
already skipping this step if the PLL is enabled, so lets extend the
same behavior to Lucid Evo variant.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20240418-clk-qcom-lucid-evo-skip-configuring-enabled-v1-1-caede5f1c7a3@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Stromer plus APSS PLL does not support dynamic frequency scaling.
To switch between frequencies, we have to shut down the PLL,
configure the L and ALPHA values and turn on again. So introduce the
separate set of ops for Stromer Plus PLL.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Link: https://lore.kernel.org/r/2affa6c63ff0c4342230623a7d4eef02ec7c02d4.1697781921.git.quic_varada@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Lucid ole pll has as extra RINGOSC_CAL_L field in L register in
addition to the fields that are part of lucid evo pll, hence add
support for lucid ole pll configure function to configure the ole plls.
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230707035744.22245-3-quic_jkona@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The "vanilla" Alpha PLL configs are sometimes provided with an intention
to only update certain bits of th register.
Do so if a mask is found.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Iskren Chernev <me@iskren.info>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230601-topic-alpha_ctl-v1-1-b6a932dfcf68@linaro.org
The lucid ole pll reuses lucid evo ops but it has an additional test
control register which is required to be programmed, add support to
program the same.
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230524145203.13153-2-quic_jkona@quicinc.com
Add the support for stromer plus pll, which is found on the IPQ5332
SoCs. Programming sequence is same as the stromer pll, so we can re-use
the same.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230307062232.4889-3-quic_kathirav@quicinc.com
Add programming sequence support for managing the Stromer
PLLs.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Co-developed-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230307062232.4889-2-quic_kathirav@quicinc.com
Program PLL_TEST and PLL_TEST_U registers if required by the pll
configuration.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230113120544.59320-3-dmitry.baryshkov@linaro.org
Add a LUCID_OLE PLL type for SM8550 SoC from Qualcomm.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221130112852.2977816-5-abel.vesa@linaro.org
The qcom2260 and sm6115 GCC drivers use a common modified DEFAULT and
BRAMMO alpha pll offsets. Move these common offsets to the shared place
to avoid duplication. The new layouts have a suffix EVO similar to LUCID
and RIVIAN.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220830075620.974009-4-iskren.chernev@gmail.com
PLLs can be kept in standby (default configuration) or in off mode
when disabled during power collapse. Hence add support for pll
disable off mode for lucid evo PLL.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220908222850.3552050-3-dmitry.baryshkov@linaro.org
Add and export Rivian EVO PLL configuration and control functions to
clock controller drivers, the PLL is used by SM8450 camera clock
controller.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220701062739.2757912-1-vladimir.zapolskiy@linaro.org
Add controls for Lucid EVO PLL configuration and export control functions
to clock controller drivers, the PLL is used by Qualcomm SM8450 camera
and display clock controllers.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220701062729.2757893-1-vladimir.zapolskiy@linaro.org
After merging lucid and trion pll functions in commit 0b01489475
("clk: qcom: clk-alpha-pll: same regs and ops for trion and lucid")
the function clk_trion_pll_configure() is left with an old description
header, which results in a W=2 compile time warning, fix it.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220701062711.2757855-1-vladimir.zapolskiy@linaro.org
they're mostly minor cleanups and some debugfs stuff. The real work
that's in here is the typical pile of clk driver updates and new SoC
support. Per usual (or maybe just recent trends), Qualcomm gains a
handful of SoC drivers additions and has the largest diffstat. After
that there are quite a few updates to the Allwinner (sunxi) drivers to
support modular drivers and Renesas is heavily updated to add more
support for various clks. Overall it looks pretty normal.
New Drivers:
- Add MDMA and BDMA clks to Ingenic JZ4760 and JZ4770
- MediaTek mt7986 SoC basic support
- Clock and reset driver for Toshiba Visconti SoCs
- Initial clock driver for the Exynos7885 SoC (Samsung Galaxy A8)
- Allwinner D1 clks
- Lan966x Generic Clock Controller driver and associated DT bindings
- Qualcomm SDX65, SM8450, and MSM8976 GCC clks
- Qualcomm SDX65 and SM8450 RPMh clks
Updates:
- Set suppress_bind_attrs to true for i.MX8ULP driver
- Switch from do_div to div64_ul for throughout all i.MX drivers
- Fix imx8mn_clko1_sels for i.MX8MN
- Remove unused IPG_AUDIO_ROOT from i.MX8MP
- Switch parent for audio_root_clk to audio ahb in i.MX8MP driver
- Removal of all remaining uses of __clk_lookup() in drivers/clk/samsung
- Refactoring of the CPU clocks registration to use common interface
- An update of the Exynos850 driver (support for more clock domains)
required by the E850-96 development board
- Prep for runtime PM and generic power domains on Tegra
- Support modular Allwinner clk drivers via platform bus
- Lan966x clock driver extended to support clock gating
- Add serial (SCI1), watchdog (WDT), timer (OSTM), SPI (RSPI), and
thermal (TSU) clocks and resets on Renesas RZ/G2L
- Rework SDHI clock handling in the Renesas R-Car Gen3 and RZ/G2 clock
drivers, and in the Renesas SDHI driver
- Make the Cortex-A55 (I) clock on Renesas RZ/G2L programmable
- Document support for the new Renesas R-Car S4-8 (R8A779F0) SoC
- Add support for the new Renesas R-Car S4-8 (R8A779F0) SoC
- Add GPU clock and resets on Renesas RZ/G2L
- Add clk-provider.h to various Qualcomm clk drivers
- devm version of clk_hw_register_gate()
- kerneldoc fixes in a couple drivers
-----BEGIN PGP SIGNATURE-----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=jB+l
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have a couple patches in the framework core this time around but
they're mostly minor cleanups and some debugfs stuff. The real work
that's in here is the typical pile of clk driver updates and new SoC
support.
Per usual (or maybe just recent trends), Qualcomm gains a handful of
SoC drivers additions and has the largest diffstat. After that there
are quite a few updates to the Allwinner (sunxi) drivers to support
modular drivers and Renesas is heavily updated to add more support for
various clks.
Overall it looks pretty normal.
New Drivers:
- Add MDMA and BDMA clks to Ingenic JZ4760 and JZ4770
- MediaTek mt7986 SoC basic support
- Clock and reset driver for Toshiba Visconti SoCs
- Initial clock driver for the Exynos7885 SoC (Samsung Galaxy A8)
- Allwinner D1 clks
- Lan966x Generic Clock Controller driver and associated DT bindings
- Qualcomm SDX65, SM8450, and MSM8976 GCC clks
- Qualcomm SDX65 and SM8450 RPMh clks
Updates:
- Set suppress_bind_attrs to true for i.MX8ULP driver
- Switch from do_div to div64_ul for throughout all i.MX drivers
- Fix imx8mn_clko1_sels for i.MX8MN
- Remove unused IPG_AUDIO_ROOT from i.MX8MP
- Switch parent for audio_root_clk to audio ahb in i.MX8MP driver
- Removal of all remaining uses of __clk_lookup() in
drivers/clk/samsung
- Refactoring of the CPU clocks registration to use common interface
- An update of the Exynos850 driver (support for more clock domains)
required by the E850-96 development board
- Prep for runtime PM and generic power domains on Tegra
- Support modular Allwinner clk drivers via platform bus
- Lan966x clock driver extended to support clock gating
- Add serial (SCI1), watchdog (WDT), timer (OSTM), SPI (RSPI), and
thermal (TSU) clocks and resets on Renesas RZ/G2L
- Rework SDHI clock handling in the Renesas R-Car Gen3 and RZ/G2
clock drivers, and in the Renesas SDHI driver
- Make the Cortex-A55 (I) clock on Renesas RZ/G2L programmable
- Document support for the new Renesas R-Car S4-8 (R8A779F0) SoC
- Add support for the new Renesas R-Car S4-8 (R8A779F0) SoC
- Add GPU clock and resets on Renesas RZ/G2L
- Add clk-provider.h to various Qualcomm clk drivers
- devm version of clk_hw_register_gate()
- kerneldoc fixes in a couple drivers"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (131 commits)
clk: visconti: Remove pointless NULL check in visconti_pll_add_lookup()
clk: mediatek: add mt7986 clock support
clk: mediatek: add mt7986 clock IDs
dt-bindings: clock: mediatek: document clk bindings for mediatek mt7986 SoC
clk: mediatek: clk-gate: Use regmap_{set/clear}_bits helpers
clk: mediatek: clk-gate: Shrink by adding clockgating bit check helper
clk: x86: Fix clk_gate_flags for RV_CLK_GATE
clk: x86: Use dynamic con_id string during clk registration
ACPI: APD: Add a fmw property clk-name
drivers: acpi: acpi_apd: Remove unused device property "is-rv"
x86: clk: clk-fch: Add support for newer family of AMD's SOC
clk: ingenic: Add MDMA and BDMA clocks
dt-bindings: clk/ingenic: Add MDMA and BDMA clocks
clk: bm1880: remove kfrees on static allocations
clk: Drop unused COMMON_CLK_STM32MP157_SCMI config
clk: st: clkgen-mux: search reg within node or parent
clk: st: clkgen-fsyn: search reg within node or parent
clk: Enable/Disable runtime PM for clk_summary
MAINTAINERS: Add entries for Toshiba Visconti PLL and clock controller
clk: visconti: Add support common clock driver and reset driver
...
This introduces bindings and drivers for the global clock controllers
found in SDX65, SM8450 and MSM8976, as well as RPMh clock support for
SDX65 and SM8450.
It cleans up the SMD RPM clock driver and it adds includes for
clk-provider.h throughout the clock providers that was lacking this.
-----BEGIN PGP SIGNATURE-----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=PGNc
-----END PGP SIGNATURE-----
Merge tag 'qcom-clk-for-5.17' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into clk-qcom
Pull qcom clk driver updates from Bjorn Andersson:
This introduces bindings and drivers for the global clock controllers
found in SDX65, SM8450 and MSM8976, as well as RPMh clock support for
SDX65 and SM8450.
It cleans up the SMD RPM clock driver and it adds includes for
clk-provider.h throughout the clock providers that was lacking this.
* tag 'qcom-clk-for-5.17' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (23 commits)
clk: qcom: turingcc-qcs404: explicitly include clk-provider.h
clk: qcom: q6sstop-qcs404: explicitly include clk-provider.h
clk: qcom: mmcc-apq8084: explicitly include clk-provider.h
clk: qcom: lpasscc-sdm845: explicitly include clk-provider.h
clk: qcom: lpasscc-sc7280: explicitly include clk-provider.h
clk: qcom: gcc-sm6350: explicitly include clk-provider.h
clk: qcom: gcc-msm8994: explicitly include clk-provider.h
clk: qcom: gcc-sm8350: explicitly include clk-provider.h
clk: qcom: Add MSM8976/56 Global Clock Controller (GCC) driver
dt-bindings: clk: qcom: Document MSM8976 Global Clock Controller
clk: qcom: Add clock driver for SM8450
clk: qcom: Add SDX65 GCC support
clk: qcom: Add LUCID_EVO PLL type for SDX65
dt-bindings: clock: Add SM8450 GCC clock bindings
dt-bindings: clock: Add SDX65 GCC clock bindings
clk: qcom: rpmh: add support for SM8450 rpmh clocks
dt-bindings: clock: Add RPMHCC bindings for SM8450
clk: qcom: smd-rpm: Drop binary value handling for buffered clock
clk: qcom: smd-rpm: Drop the use of struct rpm_cc
clk: qcom: smd-rpm: Drop MFD qcom-rpm reference
...
PLL poll for lock detection can take more than 100us for certain type
of Lucid PLLs and also the new PLLs types(Lucid EVO), thus update to 200us.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1640018638-19436-2-git-send-email-tdas@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In the event that the bootloader has configured the Trion PLL as source
for the display clocks, e.g. for the continuous splashscreen, then there
will also be RCGs that are clocked by this instance.
Reconfiguring, and in particular disabling the output of, the PLL will
cause issues for these downstream RCGs and has been shown to prevent
them from being re-parented.
Follow downstream and skip configuration if it's determined that the PLL
is already running.
Fixes: 59128c20a6 ("clk: qcom: clk-alpha-pll: Add support for controlling Lucid PLLs")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20211123162508.153711-1-bjorn.andersson@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Caught this when looking at alpha-pll code. Untested but it is clear that
this was intended to write to PLL_CAL_L_VAL and not PLL_ALPHA_VAL.
Fixes: 691865bad6 ("clk: qcom: clk-alpha-pll: Add support for Fabia PLL calibration")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20210609022852.4151-1-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
