Bluetooth controller attached via the UART is handled by the serdev driver.
Get the wakeup status from the device handle through serdev, instead of the
parent path.
Fixes: c1a74160ea ("Bluetooth: hci_qca: Add device_may_wakeup support")
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes the following warnings:
drivers/bluetooth/hci_qca.c:1014:26: warning: cast to restricted __le16
drivers/bluetooth/hci_qca.c:1028:37: warning: cast to restricted __le32
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The driver shutdown callback (which sends EDL_SOC_RESET to the device
over serdev) should not be invoked when HCI device is not open (e.g. if
hci_dev_open_sync() failed), because the serdev and its TTY are not open
either. Also skip this step if device is powered off
(qca_power_shutdown()).
The shutdown callback causes use-after-free during system reboot with
Qualcomm Atheros Bluetooth:
Unable to handle kernel paging request at virtual address
0072662f67726fd7
...
CPU: 6 PID: 1 Comm: systemd-shutdow Tainted: G W
6.1.0-rt5-00325-g8a5f56bcfcca #8
Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
Call trace:
tty_driver_flush_buffer+0x4/0x30
serdev_device_write_flush+0x24/0x34
qca_serdev_shutdown+0x80/0x130 [hci_uart]
device_shutdown+0x15c/0x260
kernel_restart+0x48/0xac
KASAN report:
BUG: KASAN: use-after-free in tty_driver_flush_buffer+0x1c/0x50
Read of size 8 at addr ffff16270c2e0018 by task systemd-shutdow/1
CPU: 7 PID: 1 Comm: systemd-shutdow Not tainted
6.1.0-next-20221220-00014-gb85aaf97fb01-dirty #28
Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
Call trace:
dump_backtrace.part.0+0xdc/0xf0
show_stack+0x18/0x30
dump_stack_lvl+0x68/0x84
print_report+0x188/0x488
kasan_report+0xa4/0xf0
__asan_load8+0x80/0xac
tty_driver_flush_buffer+0x1c/0x50
ttyport_write_flush+0x34/0x44
serdev_device_write_flush+0x48/0x60
qca_serdev_shutdown+0x124/0x274
device_shutdown+0x1e8/0x350
kernel_restart+0x48/0xb0
__do_sys_reboot+0x244/0x2d0
__arm64_sys_reboot+0x54/0x70
invoke_syscall+0x60/0x190
el0_svc_common.constprop.0+0x7c/0x160
do_el0_svc+0x44/0xf0
el0_svc+0x2c/0x6c
el0t_64_sync_handler+0xbc/0x140
el0t_64_sync+0x190/0x194
Fixes: 7e7bbddd02 ("Bluetooth: hci_qca: Fix qca6390 enable failure after warm reboot")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Core
----
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations.
- Add inet drop monitor support.
- A few GRO performance improvements.
- Add infrastructure for atomic dev stats, addressing long standing
data races.
- De-duplicate common code between OVS and conntrack offloading
infrastructure.
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements.
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up
the workload with the number of available CPUs.
- Add the helper support for connection-tracking OVS offload.
BPF
---
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF.
- Make cgroup local storage available to non-cgroup attached BPF
programs.
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers.
- A relevant bunch of BPF verifier fixes and improvements.
- Veristat tool improvements to support custom filtering, sorting,
and replay of results.
- Add LLVM disassembler as default library for dumping JITed code.
- Lots of new BPF documentation for various BPF maps.
- Add bpf_rcu_read_{,un}lock() support for sleepable programs.
- Add RCU grace period chaining to BPF to wait for the completion
of access from both sleepable and non-sleepable BPF programs.
- Add support storing struct task_struct objects as kptrs in maps.
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values.
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions.
Protocols
---------
- TCP: implement Protective Load Balancing across switch links.
- TCP: allow dynamically disabling TCP-MD5 static key, reverting
back to fast[er]-path.
- UDP: Introduce optional per-netns hash lookup table.
- IPv6: simplify and cleanup sockets disposal.
- Netlink: support different type policies for each generic
netlink operation.
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support.
- MPTCP: add netlink notification support for listener sockets
events.
- SCTP: add VRF support, allowing sctp sockets binding to VRF
devices.
- Add bridging MAC Authentication Bypass (MAB) support.
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios.
- More work for Wi-Fi 7 support, comprising conversion of all
the existing drivers to internal TX queue usage.
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading.
- IPSec: extended ack support for more descriptive XFRM error
reporting.
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking.
- IEEE 802154: synchronous send frame and extended filtering
support, initial support for scanning available 15.4 networks.
- Tun: bump the link speed from 10Mbps to 10Gbps.
- Tun/VirtioNet: implement UDP segmentation offload support.
Driver API
----------
- PHY/SFP: improve power level switching between standard
level 1 and the higher power levels.
- New API for netdev <-> devlink_port linkage.
- PTP: convert existing drivers to new frequency adjustment
implementation.
- DSA: add support for rx offloading.
- Autoload DSA tagging driver when dynamically changing protocol.
- Add new PCP and APPTRUST attributes to Data Center Bridging.
- Add configuration support for 800Gbps link speed.
- Add devlink port function attribute to enable/disable RoCE and
migratable.
- Extend devlink-rate to support strict prioriry and weighted fair
queuing.
- Add devlink support to directly reading from region memory.
- New device tree helper to fetch MAC address from nvmem.
- New big TCP helper to simplify temporary header stripping.
New hardware / drivers
----------------------
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches.
- Marvel Prestera AC5X Ethernet Switch.
- WangXun 10 Gigabit NIC.
- Motorcomm yt8521 Gigabit Ethernet.
- Microchip ksz9563 Gigabit Ethernet Switch.
- Microsoft Azure Network Adapter.
- Linux Automation 10Base-T1L adapter.
- PHY:
- Aquantia AQR112 and AQR412.
- Motorcomm YT8531S.
- PTP:
- Orolia ART-CARD.
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices.
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices.
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets.
- Realtek RTL8852BE and RTL8723DS.
- Cypress.CYW4373A0 WiFi + Bluetooth combo device.
Drivers
-------
- CAN:
- gs_usb: bus error reporting support.
- kvaser_usb: listen only and bus error reporting support.
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping.
- implement devlink-rate support.
- support direct read from memory.
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate.
- Support for enhanced events compression.
- extend H/W offload packet manipulation capabilities.
- implement IPSec packet offload mode.
- nVidia/Mellanox (mlx4):
- better big TCP support.
- Netronome Ethernet NICs (nfp):
- IPsec offload support.
- add support for multicast filter.
- Broadcom:
- RSS and PTP support improvements.
- AMD/SolarFlare:
- netlink extened ack improvements.
- add basic flower matches to offload, and related stats.
- Virtual NICs:
- ibmvnic: introduce affinity hint support.
- small / embedded:
- FreeScale fec: add initial XDP support.
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood.
- TI am65-cpsw: add suspend/resume support.
- Mediatek MT7986: add RX wireless wthernet dispatch support.
- Realtek 8169: enable GRO software interrupt coalescing per
default.
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP.
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support.
- add ip6gre support.
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support.
- enable flow offload support.
- Renesas:
- add rswitch R-Car Gen4 gPTP support.
- Microchip (lan966x):
- add full XDP support.
- add TC H/W offload via VCAP.
- enable PTP on bridge interfaces.
- Microchip (ksz8):
- add MTU support for KSZ8 series.
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan.
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support.
- add ack signal support.
- enable coredump support.
- remain_on_channel support.
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities.
- 320 MHz channels support.
- RealTek WiFi (rtw89):
- new dynamic header firmware format support.
- wake-over-WLAN support.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=CbJC
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core:
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations
- Add inet drop monitor support
- A few GRO performance improvements
- Add infrastructure for atomic dev stats, addressing long standing
data races
- De-duplicate common code between OVS and conntrack offloading
infrastructure
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up the
workload with the number of available CPUs
- Add the helper support for connection-tracking OVS offload
BPF:
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF
- Make cgroup local storage available to non-cgroup attached BPF
programs
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers
- A relevant bunch of BPF verifier fixes and improvements
- Veristat tool improvements to support custom filtering, sorting,
and replay of results
- Add LLVM disassembler as default library for dumping JITed code
- Lots of new BPF documentation for various BPF maps
- Add bpf_rcu_read_{,un}lock() support for sleepable programs
- Add RCU grace period chaining to BPF to wait for the completion of
access from both sleepable and non-sleepable BPF programs
- Add support storing struct task_struct objects as kptrs in maps
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions
Protocols:
- TCP: implement Protective Load Balancing across switch links
- TCP: allow dynamically disabling TCP-MD5 static key, reverting back
to fast[er]-path
- UDP: Introduce optional per-netns hash lookup table
- IPv6: simplify and cleanup sockets disposal
- Netlink: support different type policies for each generic netlink
operation
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support
- MPTCP: add netlink notification support for listener sockets events
- SCTP: add VRF support, allowing sctp sockets binding to VRF devices
- Add bridging MAC Authentication Bypass (MAB) support
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios
- More work for Wi-Fi 7 support, comprising conversion of all the
existing drivers to internal TX queue usage
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading
- IPSec: extended ack support for more descriptive XFRM error
reporting
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking
- IEEE 802154: synchronous send frame and extended filtering support,
initial support for scanning available 15.4 networks
- Tun: bump the link speed from 10Mbps to 10Gbps
- Tun/VirtioNet: implement UDP segmentation offload support
Driver API:
- PHY/SFP: improve power level switching between standard level 1 and
the higher power levels
- New API for netdev <-> devlink_port linkage
- PTP: convert existing drivers to new frequency adjustment
implementation
- DSA: add support for rx offloading
- Autoload DSA tagging driver when dynamically changing protocol
- Add new PCP and APPTRUST attributes to Data Center Bridging
- Add configuration support for 800Gbps link speed
- Add devlink port function attribute to enable/disable RoCE and
migratable
- Extend devlink-rate to support strict prioriry and weighted fair
queuing
- Add devlink support to directly reading from region memory
- New device tree helper to fetch MAC address from nvmem
- New big TCP helper to simplify temporary header stripping
New hardware / drivers:
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches
- Marvel Prestera AC5X Ethernet Switch
- WangXun 10 Gigabit NIC
- Motorcomm yt8521 Gigabit Ethernet
- Microchip ksz9563 Gigabit Ethernet Switch
- Microsoft Azure Network Adapter
- Linux Automation 10Base-T1L adapter
- PHY:
- Aquantia AQR112 and AQR412
- Motorcomm YT8531S
- PTP:
- Orolia ART-CARD
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets
- Realtek RTL8852BE and RTL8723DS
- Cypress.CYW4373A0 WiFi + Bluetooth combo device
Drivers:
- CAN:
- gs_usb: bus error reporting support
- kvaser_usb: listen only and bus error reporting support
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping
- implement devlink-rate support
- support direct read from memory
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate
- Support for enhanced events compression
- extend H/W offload packet manipulation capabilities
- implement IPSec packet offload mode
- nVidia/Mellanox (mlx4):
- better big TCP support
- Netronome Ethernet NICs (nfp):
- IPsec offload support
- add support for multicast filter
- Broadcom:
- RSS and PTP support improvements
- AMD/SolarFlare:
- netlink extened ack improvements
- add basic flower matches to offload, and related stats
- Virtual NICs:
- ibmvnic: introduce affinity hint support
- small / embedded:
- FreeScale fec: add initial XDP support
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood
- TI am65-cpsw: add suspend/resume support
- Mediatek MT7986: add RX wireless wthernet dispatch support
- Realtek 8169: enable GRO software interrupt coalescing per
default
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support
- add ip6gre support
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support
- enable flow offload support
- Renesas:
- add rswitch R-Car Gen4 gPTP support
- Microchip (lan966x):
- add full XDP support
- add TC H/W offload via VCAP
- enable PTP on bridge interfaces
- Microchip (ksz8):
- add MTU support for KSZ8 series
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support
- add ack signal support
- enable coredump support
- remain_on_channel support
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
- 320 MHz channels support
- RealTek WiFi (rtw89):
- new dynamic header firmware format support
- wake-over-WLAN support"
* tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2002 commits)
ipvs: fix type warning in do_div() on 32 bit
net: lan966x: Remove a useless test in lan966x_ptp_add_trap()
net: ipa: add IPA v4.7 support
dt-bindings: net: qcom,ipa: Add SM6350 compatible
bnxt: Use generic HBH removal helper in tx path
IPv6/GRO: generic helper to remove temporary HBH/jumbo header in driver
selftests: forwarding: Add bridge MDB test
selftests: forwarding: Rename bridge_mdb test
bridge: mcast: Support replacement of MDB port group entries
bridge: mcast: Allow user space to specify MDB entry routing protocol
bridge: mcast: Allow user space to add (*, G) with a source list and filter mode
bridge: mcast: Add support for (*, G) with a source list and filter mode
bridge: mcast: Avoid arming group timer when (S, G) corresponds to a source
bridge: mcast: Add a flag for user installed source entries
bridge: mcast: Expose __br_multicast_del_group_src()
bridge: mcast: Expose br_multicast_new_group_src()
bridge: mcast: Add a centralized error path
bridge: mcast: Place netlink policy before validation functions
bridge: mcast: Split (*, G) and (S, G) addition into different functions
bridge: mcast: Do not derive entry type from its filter mode
...
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 0ff252c197 ("Bluetooth: hciuart: Add support QCA chipset for UART")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Only assign hdev->wakeup if the serial port supports wakeup. Otherwise
it will fall back to the hci_uart_wakeup or the behavior that can be
overridden before calling the hci_uart_register_device().
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
While discussing solutions for the teardown problem which results from
circular dependencies between timers and workqueues, where timers schedule
work from their timer callback and workqueues arm the timers from work
items, it was discovered that the recent fix to the QCA code is incorrect.
That commit fixes the obvious problem of using del_timer() instead of
del_timer_sync() and reorders the teardown calls to
destroy_workqueue(wq);
del_timer_sync(t);
This makes it less likely to explode, but it's still broken:
destroy_workqueue(wq);
/* After this point @wq cannot be touched anymore */
---> timer expires
queue_work(wq) <---- Results in a NULL pointer dereference
deep in the work queue core code.
del_timer_sync(t);
Use the new timer_shutdown_sync() function to ensure that the timers are
disarmed, no timer callbacks are running and the timers cannot be armed
again. This restores the original teardown sequence:
timer_shutdown_sync(t);
destroy_workqueue(wq);
which is now correct because the timer core silently ignores potential
rearming attempts which can happen when destroy_workqueue() drains pending
work before mopping up the workqueue.
Fixes: 72ef98445a ("Bluetooth: hci_qca: Use del_timer_sync() before freeing")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Acked-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/all/87iljhsftt.ffs@tglx
Link: https://lore.kernel.org/r/20221123201625.435907114@linutronix.de
This fixes the return value of qca_wakeup(), since
.wakeup work inversely with original .prevent_wake.
Fixes: 4539ca67fe (Bluetooth: Rename driver .prevent_wake to .wakeup)
Signed-off-by: Sai Teja Aluvala <quic_saluvala@quicinc.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
While looking at a crash report on a timer list being corrupted, which
usually happens when a timer is freed while still active. This is
commonly triggered by code calling del_timer() instead of
del_timer_sync() just before freeing.
One possible culprit is the hci_qca driver, which does exactly that.
Eric mentioned that wake_retrans_timer could be rearmed via the work
queue, so also move the destruction of the work queue before
del_timer_sync().
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: stable@vger.kernel.org
Fixes: 0ff252c197 ("Bluetooth: hciuart: Add support QCA chipset for UART")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The function devm_gpiod_get_index() return error pointers on error.
Thus devm_gpiod_get_index_optional() could return NULL and error pointers.
The same as devm_gpiod_get_optional() function. Using IS_ERR_OR_NULL()
check to catch error pointers.
Fixes: 77131dfe ("Bluetooth: hci_qca: Replace devm_gpiod_get() with devm_gpiod_get_optional()")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The IBS timers are not stopped properly once BT OFF is triggered.
we could see IBS commands being sent along with version command,
so stopped IBS timers while Bluetooth is off.
Fixes: 3e4be65eb8 ("Bluetooth: hci_qca: Add poweroff support during hci down for wcn3990")
Signed-off-by: Panicker Harish <quic_pharish@quicinc.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
prevent_wake logic is backward since what it is really checking is
if the device may wakeup the system or not, not that it will prevent
the to be awaken.
Also looking on how other subsystems have the entry as power/wakeup
this also renames the force_prevent_wake to force_wakeup in vhci driver.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch enables Qualcomm WCN399x to support the AOSP extension.
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Joseph Hwang <josephsih@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Added regulators,GPIOs and changes required to power on/off wcn6750.
Added support for firmware download for wcn6750.
Changes done in detail:
1. Added regulators and corresponding current values.
2. Added sw_ctrl GPIO pin which is output from BT SoC and indicates
status of clock supply to BT SoC.
3. Added inline function to check if the SoC type is wcn6750.
4. Modified the function qca_wcn3990_init() to support wcn6750 and
renamed it to qca_regulator_init().
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In qca_power_shutdown() qcadev local variable is
initialized by hu->serdev.dev private data, but
hu->serdev can be NULL and there is a check for it.
Since, qcadev is not used before
if (!hu->serdev)
return;
we can move its initialization after this "if" to
prevent GPF.
Fixes: 5559904ccc ("Bluetooth: hci_qca: Add QCA Rome power off support to the qca_power_shutdown()")
Cc: stable@vger.kernel.org # v5.6+
Cc: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Based on device may wakeup status, Bluez stack will enable/disable
passive scanning with whitelist in BT controller while suspending.
As interrupt from BT SoC is handled by UART driver,we need to use
device handle of UART driver to get the status of device may wakeup
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If BT SoC is running with ROM FW then just return in
qca_suspend function as ROM FW does not support
in-band sleep.
Fixes: 2be43abac5 ("Bluetooth: hci_qca: Wait for timeout during suspend")
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
QCA_IBS_DISABLED flag will be set after memorydump started from
controller.Currently qca_suspend() is waiting for SSR to complete
based on flag QCA_IBS_DISABLED.Added to check for QCA_SSR_TRIGGERED
flag too.
Fixes: 2be43abac5 ("Bluetooth: hci_qca: Wait for timeout during suspend")
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During SSR after memory dump collection,BT controller will be powered off,
powered on and then FW will be downloaded.During suspend if BT controller
is powered off due to SSR then we should wait until SSR is completed and
then suspend.
Fixes: 2be43abac5 ("Bluetooth: hci_qca: Wait for timeout during suspend")
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When __le32_to_cpu() fails, qca_memdump should be freed
just like when vmalloc() fails.
Fixes: d841502c79 ("Bluetooth: hci_qca: Collect controller memory dump during SSR")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change will allow to use different NVM file based
on WCN3991 BT SoC ID.Need to use different NVM file based on
fab location for WCN3991 BT SoC.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Currently qca_suspend() is relied on IBS mechanism. During
FW download and memory dump collections, IBS will be disabled.
In those cases, driver will allow suspend and still uses the
serdev port, which results to errors. Now added a wait timeout
if suspend is triggered during FW download and memory collections.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Replace symbolic permissions with octal values. Use usleep_range
for small msec values due to the fact that msleep() less than
20ms may have unexpected behavior/sleep longer.
- https://lkml.org/lkml/2016/8/2/1945
- Documentation/timers/timers-howto.rst
Signed-off-by: Nigel Christian <nigel.l.christian@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently driver only retries to download FW if FW downloading
is failed. Sometimes observed command timeout for version request
command, if this happen on some platforms during boot time, then
a reboot is needed to turn ON BT. Instead to avoid a reboot, now
extended retry logic for version request command too.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
WCN3991 supports connectable advertisements so we need to add the valid
le states quirk so the 'central-peripheral' role is exposed in
userspace.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During serdev unregister, hdev->shutdown is called before
proto close. Removing duplicates power OFF call.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Because clk_disable_unprepare already checked
NULL clock parameter, so the additional check is
unnecessary, just remove it.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Setting memdump state to idle prior to setting of callback function
pointer for command timeout to NULL,causing the issue.Now moved the
initialisation of memdump state to qca_setup().
Fixes: d841502c79 ("Bluetooth: hci_qca: Collect controller memory dump during SSR")
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
1.During SSR for command time out if BT SoC goes to inresponsive
state, power cycling of BT SoC was not happening. Given the fix by
sending hw error event to reset the BT SoC.
2.If SSR is triggered then ignore the transmit data requests to
BT SoC until SSR is completed.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tx pending flag is set to true when HOST IBS state is AWAKE or
AWAKEING. If IBS state is ASLEEP, then Tx clock is already voted
off. To optimize further directly calling serial_clock_vote()
instead of qca_wq_serial_tx_clock_vote_off(), at this point of
qca_suspend() already data is sent out. No need to wake up hci to
send data.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In some version of WCN399x, SoC idle timeout is configured
as 80ms instead of 20ms or 40ms. To honor all the SoC's
supported in the driver increasing SoC idle timeout to 200ms.
Fixes: 41d5b25fed ("Bluetooth: hci_qca: add PM support")
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Due to race conditions between qca_hw_error and qca_controller_memdump
during SSR timeout,the same pointer is freed twice. This results in a
double free. Now a lock is acquired before checking the stauts of SSR
state.
Fixes: d841502c79 ("Bluetooth: hci_qca: Collect controller memory dump during SSR")
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If waiting for IBS sleep times out jump to the error handler, this is
easier to read than multiple 'if' branches and a fall through to the
error handler.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
qca_suspend() calls serdev_device_wait_until_sent() regardless of
whether a transfer is pending. While it does no active harm since
the function should return immediately it makes the code more
confusing. Add a flag to track whether a transfer is pending and
only call serdev_device_wait_until_sent() is needed.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
qca_suspend() removes the vote for the UART TX clock after
writing an IBS sleep request to the serial buffer. This is
not a good idea since there is no guarantee that the request
has been sent at this point. Instead remove the vote after
successfully entering IBS sleep. This also fixes the issue
of the vote being removed in case of an aborted suspend due
to a failure of entering IBS sleep.
Fixes: 41d5b25fed ("Bluetooth: hci_qca: add PM support")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The serial clocks should be on when there is a vote for at least one
of the clocks (RX or TX), and off when there is no 'on' vote. The
current logic to determine the combined state is a bit redundant
in the code paths for different types of votes, use a single
statement in the common path instead.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When a function like devm_clk_get_optional() function returns both error
pointers on error and NULL then the NULL return means that the optional
feature is deliberately disabled. It is a special sort of success and
should not trigger an error message. The surrounding code should be
written to check for NULL and not crash.
On the other hand, if we encounter an error, then the probe from should
clean up and return a failure.
In this code, if devm_clk_get_optional() returns an error pointer then
the kernel will crash inside the call to:
clk_set_rate(qcadev->susclk, SUSCLK_RATE_32KHZ);
The error handling must be updated to prevent that.
Fixes: 77131dfec6 ("Bluetooth: hci_qca: Replace devm_gpiod_get() with devm_gpiod_get_optional()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
QCA6390 memdump VSE sometimes come to bluetooth driver
with wrong sequence number as illustrated as follows:
frame # in dec: frame data in hex
1396: ff fd 01 08 74 05 00 37 8f 14
1397: ff fd 01 08 75 05 00 ff bf 38
1414: ff fd 01 08 86 05 00 fb 5e 4b
1399: ff fd 01 08 77 05 00 f3 44 0a
1400: ff fd 01 08 78 05 00 ca f7 41
it is mistook for controller missing packets, so results
in page fault after overwriting memdump buffer allocated.
Fixed by ignoring QCA6390 sequence number check and
checking buffer space before writing.
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Tested-by: Zijun Hu <zijuhu@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Warm reboot can not reset controller qca6390 due to
lack of controllable power supply, so causes firmware
download failure during enable.
Fixed by sending VSC EDL_SOC_RESET to reset qca6390
within added device shutdown implementation.
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Tested-by: Zijun Hu <zijuhu@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
@dev parameter of qca_suspend()/qca_resume() represents
serdev_device, but it is mistook for hci_dev and causes
succedent unexpected memory access.
Fix by taking @dev as serdev_device.
Fixes: 41d5b25fed ("Bluetooth: hci_qca: add PM support")
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hdev is always allocated and not only when power control is required.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
WCN3991 supports transparent WBS (host encoded mSBC). Add a flag to the
device match data to show WBS is supported.
This requires the matching firmware for WCN3991 in linux-firmware:
1a8b0dc00f77 (qca: Enable transparent WBS for WCN3991)
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Move the read of max-speed from device-tree out of the qca_is_wcn399x
if block so oper_speed can be set for QCA9377 devices as well.
Suggested-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add a compatible so QCA9377 devices can be defined in device-tree.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for QCA6390, including the devicetree and acpi
compatible hwid matching, and patch/nvm downloading.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces devm_gpiod_get() with devm_gpiod_get_optional() to get
bt_en and replaces devm_clk_get() with devm_clk_get_optional() to get
susclk. It also uses NULL check to determine whether the resource is
available or not.
Fixes: 8a208b24d7 ("Bluetooth: hci_qca: Make bt_en and susclk not mandatory for QCA Rome")
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On some platforms the bt_en pin and susclk are default on and there
is no exposed resource to control them. This patch makes the bt_en
and susclk not mandatory to have BT work. It also will not set the
HCI_QUIRK_NON_PERSISTENT_SETUP and shutdown() callback if bt_en is
not available.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
QCA Rome doesn't support the pre-shutdown vendor hci command, this patch
will check the soc type in qca_power_off() and only send this command
for wcn399x.
Fixes: ae563183b6 ("Bluetooth: hci_qca: Enable power off/on support during hci down/up for QCA Rome")
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch will fix the below issues
1. Discarding memory dump events if memdump state is moved to
MEMDUMP_TIMEOUT.
2. Fixed race conditions between qca_hw_error() and qca_controller_memdump
while free memory dump buffers using mutex lock
3. Moved timeout timer to delayed work queue
4. Injecting HW error event in a case when dumps failed to receive and HW
error event is not yet received.
5. Clearing hw error and command timeout function callbacks before
sending pre shutdown command.
Collecting memory dump will follow any of the below sequence.
Sequence 1:
Receiving Memory dump events from the controller
Received entire dump in stipulated time
Received HW error event from the controller
Controller Reset from HOST
Sequence 2:
Receiving Memory dump events from the controller
Failed to Receive entire dump in stipulated time
A Timeout schedules and if no HW error event received a fake HW
error event will be injected.
Controller Reset from HOST.
Sequence 3:
Received HW error event
HOST trigger SSR by sending crash packet to controller.
Received entire dump in stipulated time
Controller Reset from HOST
Fixes: d841502c79 ("Bluetooth: hci_qca: Collect controller memory dump during SSR")
Reported-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Directly passing clock pointer to clock code without checking for NULL
as clock code takes care of it
* Removed the comment which was not necessary
* Updated code for return in qca_regulator_enable()
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of relying on other subsytem to turn ON clocks
required for BT SoC to operate, voting them from the driver.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch registers hdev->shutdown() callback and also sets
HCI_QUIRK_NON_PERSISTENT_SETUP for QCA Rome. It will power-off the BT chip
during hci down and power-on/initialize the chip again during hci up. As
wcn399x already enabled this, this patch also removed the callback register
and QUIRK setting in qca_setup() for wcn399x and uniformly do this in the
probe() routine.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the retry of btsoc initialization when it fails. There are
reports that the btsoc initialization may fail on some platforms but the
repro ratio is very low. The symptoms is the firmware downloading failed
due to the UART write timed out. The failure may be caused by UART,
platform HW or the btsoc itself but it's very difficlut to root cause,
given the repro ratio is very low. Add a retry for the btsoc initialization
can work around most of the failures and make Bluetooth finally works.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Current qca_power_shutdown() only supports wcn399x, this patch adds Rome
power off support to it. For Rome it just needs to pull down the bt_en
GPIO to power off it. This patch also replaces all the power off operation
in qca_close() with the unified qca_power_shutdown() call.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a unified API qca_power_on() to support both wcn399x and
Rome power on. For wcn399x it calls the qca_wcn3990_init() to init the
regulators, and for Rome it pulls up the bt_en GPIO to power up the btsoc.
It also moves all the power up operation from hdev->open() to
hdev->setup().
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/bluetooth/hci_qca.c: In function 'qca_controller_memdump':
drivers/bluetooth/hci_qca.c:980:6: warning:
variable 'opcode' set but not used [-Wunused-but-set-variable]
It is never used since commit d841502c79 ("Bluetooth: hci_qca: Collect
controller memory dump during SSR"), so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We will collect the ramdump of BT controller when hardware error event
received before rebooting the HCI layer. Before restarting a subsystem
or a process running on a subsystem, it is often required to request
either a subsystem or a process to perform proper cache dump and
software failure reason into a memory buffer which application
processor can retrieve afterwards. SW developers can often provide
initial investigation by looking into that debugging information.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Replace of_device_get_match_data with device_get_match_data to make driver
work across platforms.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch add support for WCN3991 i.e. current values and fw download
support.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add PM suspend/resume callbacks for hci_qca driver.
BT host will make sure both Rx and Tx go into sleep state in
qca_suspend. Without this, Tx may still remain in awake state, which
prevents BTSOC from entering deep sleep. For example, BlueZ will send
Set Event Mask to device when suspending and this will wake the device
Rx up. However, the Tx idle timeout on the host side is 2000 ms. If the
host is suspended before its Tx idle times out, it won't send
HCI_IBS_SLEEP_IND to the device and the device Rx will remain awake.
We implement this by canceling relevant work in workqueue, sending
HCI_IBS_SLEEP_IND to the device and then waiting HCI_IBS_SLEEP_IND sent
by the device.
In order to prevent the device from being awaken again after qca_suspend
is called, we introduce QCA_SUSPEND flag. QCA_SUSPEND is set in the
beginning of qca_suspend to indicate system is suspending and that we'd
like to ignore any further wake events.
With QCA_SUSPEND and spinlock, we can avoid race condition, e.g. if
qca_enqueue acquires qca->hci_ibs_lock before qca_suspend calls
cancel_work_sync and then qca_enqueue adds a new qca->ws_awake_device
work after the previous one is cancelled.
If BTSOC wants to wake the whole system up after qca_suspend is called,
it will keep sending HCI_IBS_WAKE_IND and uart driver will take care of
waking the system. For example, uart driver will reconfigure its Rx pin
to a normal GPIO pin and enable irq wake on that pin when suspending.
Once host detects Rx falling, the system will begin resuming. Then, the
BT host clears QCA_SUSPEND flag in qca_resume and begins dealing with
normal HCI packets. By doing so, only a few HCI_IBS_WAKE_IND packets are
lost and there is no data packet loss.
Signed-off-by: Claire Chang <tientzu@chromium.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This reverts commit cde9dde6e1.
The frame reassembly errors were root caused to a transient gpio issue.
The missing response was root caused to an issue with properly managing
RFR in the uart driver. Addressing those root causes occurs outside of
hci_qca and eliminates the need for the 50ms delay, so remove it.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Split and rename qca_power_setup() in order to simplify each code path
and to clarify that it is unrelated to qca_power_off() and
qca_power_setup().
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With the regulator_set_load() and regulator_set_voltage() out of the
enable/disable code paths the code can now use the standard
regulator bulk enable/disable API.
By cloning num_vregs into struct qca_power there's no need to lug around
a reference to the struct qca_vreg_data, which further simplifies
qca_power_setup().
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Devices with specific voltage requirements should not request voltage
from the driver, but instead rely on the system configuration to define
appropriate voltages for each rail.
This ensures that PMIC and board variations are accounted for, something
that the 0.1V range in the hci_qca driver currently tries to address.
But on the Lenovo Yoga C630 (with wcn3990) vddch0 is 3.1V, which means
the driver will fail to set the voltage.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the introduction of '5451781dadf8 ("regulator: core: Only count
load for enabled consumers")' in v5.0, the requested load of a regulator
consumer is only accounted for when said consumer is voted enabled.
So there's no need to vote for load ever time the regulator is
enabled or disabled.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On the msm8998 mtp, the response to the baudrate change command is never
received. On the Lenovo Miix 630, the response to the baudrate change
command is corrupted - "Frame reassembly failed (-84)".
Adding a 50ms delay before re-enabling flow to receive the baudrate change
command response from the wcn3990 addesses both issues, and allows
bluetooth to become functional.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When SoC receives pre shut down command, it share the same
with other COEX shared clients. So SoC needs a short time
after sending VS pre shutdown command before turning off
the regulators and sending the power off pulse. Along with
short delay, needs to wait for command complete event for
Pre shutdown VS command
Signed-off-by: Harish Bandi <c-hbandi@codeaurora.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
QCA UART Bluetooth controllers can do both LE scan and BR/EDR inquiry
at once, need to set HCI_QUIRK_SIMULTANEOUS_DISCOVERY quirk.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Static structure qca_proto, of type hci_uart_proto, is used four times:
as the last argument in function hci_uart_register_device(), and as the
only argument to functions hci_uart_register_proto() and
hci_uart_unregister_proto(). In all three of these functions, the
parameter corresponding to qca_proto is declared as constant. Therefore,
make qca_proto itself constant as well in order to protect it from
unintended modification.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The qca_data structure is allocated with kzalloc() and hence
zero-initialized. Remove a bunch of unnecessary explicit
initializations of struct members to zero.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Looks like Deadlock is observed in hci_qca while performing
stress and stability tests. Since same lock is getting
acquired from qca_wq_awake_rx and hci_ibs_tx_idle_timeout
seeing spinlock recursion, irqs should be disable while
acquiring the spinlock always.
Signed-off-by: Harish Bandi <c-hbandi@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Don't fall through to print error message when receive sleep indication
in HCI_IBS_RX_ASLEEP state, this is allowed behavior.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
WCN399x chips are coex chips, it needs a VS pre shutdown
command while turning off the BT. So that chip can inform
BT is OFF to other active clients.
Signed-off-by: Harish Bandi <c-hbandi@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Certain ttys operations (pty_unix98_ops) lack tiocmget() and tiocmset()
functions which are called by the certain HCI UART protocols (hci_ath,
hci_bcm, hci_intel, hci_mrvl, hci_qca) via hci_uart_set_flow_control()
or directly. This leads to an execution at NULL and can be triggered by
an unprivileged user. Fix this by adding a helper function and a check
for the missing tty operations in the protocols code.
This fixes CVE-2019-10207. The Fixes: lines list commits where calls to
tiocm[gs]et() or hci_uart_set_flow_control() were added to the HCI UART
protocols.
Link: https://syzkaller.appspot.com/bug?id=1b42faa2848963564a5b1b7f8c837ea7b55ffa50
Reported-by: syzbot+79337b501d6aa974d0f6@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org # v2.6.36+
Fixes: b3190df628 ("Bluetooth: Support for Atheros AR300x serial chip")
Fixes: 118612fb91 ("Bluetooth: hci_bcm: Add suspend/resume PM functions")
Fixes: ff2895592f ("Bluetooth: hci_intel: Add Intel baudrate configuration support")
Fixes: 162f812f23 ("Bluetooth: hci_uart: Add Marvell support")
Fixes: fa9ad876b8 ("Bluetooth: hci_qca: Add support for Qualcomm Bluetooth chip wcn3990")
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Yu-Chen, Cho <acho@suse.com>
Tested-by: Yu-Chen, Cho <acho@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
QCA BTSOC NVM is a customized firmware file and different vendors may
want to have different BTSOC configuration (e.g. Configure SCO over PCM
or I2S, Setting Tx power, etc.) via this file. This patch will allow
vendors to download different NVM firmware file by reading a device
property "firmware-name".
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Tested-by: Harish Bandi <c-hbandi@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Firmware download to the WCN3990 often fails with a 'TLV response size
mismatch' error:
[ 133.064659] Bluetooth: hci0: setting up wcn3990
[ 133.489150] Bluetooth: hci0: QCA controller version 0x02140201
[ 133.495245] Bluetooth: hci0: QCA Downloading qca/crbtfw21.tlv
[ 133.507214] Bluetooth: hci0: QCA TLV response size mismatch
[ 133.513265] Bluetooth: hci0: QCA Failed to download patch (-84)
This is caused by a vendor event that corresponds to an earlier command
to change the baudrate. The event is not processed in the context of the
baudrate change and is later interpreted as response to the firmware
download command (which is also a vendor command), but the driver detects
that the event doesn't have the expected amount of associated data.
More details:
For the WCN3990 the vendor command for a baudrate change isn't sent as
synchronous HCI command, because the controller sends the corresponding
vendor event with the new baudrate. The event is received and decoded
after the baudrate change of the host port.
Identify the 'unused' event when it is received and don't add it to
the queue of RX frames.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 136 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.384967451@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename STATE_IN_BAND_SLEEP_ENABLED to QCA_IBS_ENABLED. The constant
represents a flag (multiple flags can be set at once), not a unique
state of the controller or driver.
Also make the flag an enum value instead of a pre-processor constant
(more flags will be added to the enum group by another patch).
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Added new compatible for WCN3998 and corresponding voltage
and current values to WCN3998 compatible.
Changed driver code to support WCN3998
Signed-off-by: Harish Bandi <c-hbandi@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
qca_set_baudrate() calls serdev_device_wait_until_sent() assuming that
the HCI is always associated with a serdev device. This isn't true for
ROME controllers instantiated through ldisc, where the call causes a
crash due to a NULL pointer dereferentiation. Only call the function
when we have a serdev device. The timeout for ROME devices at the end
of qca_set_baudrate() is long enough to be reasonably sure that the
command was sent.
Fixes: fa9ad876b8 ("Bluetooth: hci_qca: Add support for Qualcomm Bluetooth chip wcn3990")
Reported-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reported-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Rocky Liao <rjliao@codeaurora.org>
Tested-by: Rocky Liao <rjliao@codeaurora.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Many functions obtain a 'struct qca_serdev' only to read the btsoc_type
field. Add a helper function that encapsulates this.
This also fixes crashes observed on platforms with ROME controllers
that are instantiated through ldisc and not as serdev clients. The
crashes are caused by NULL pointer dereferentiations, which stem from
the driver's assumption that a QCA HCI device is always associated with
a serdev device.
Fixes: fa9ad876b8 ("Bluetooth: hci_qca: Add support for Qualcomm Bluetooth chip wcn3990")
Reported-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The current 300ms delay after a baudrate change is extremely long.
For WCN3990 it is sufficient to wait 10ms after the baudrate change
request has been sent over the wire.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During initialization the power-on pulse is currently sent inmediately
after the prior power-off pulse. With this initialization often fails
at boot time:
[ 15.205224] Bluetooth: hci0: setting up wcn3990
[ 17.341062] Bluetooth: hci0: command 0xfc00 tx timeout
[ 22.101453] ERROR: Bluetooth initialization failed
[ 25.337740] Bluetooth: hci0: Reading QCA version information failed (-110)
After a power-off pulse wait 10ms to give the controller time to power
off. Remove the previous short settling delay, it isn't needed anymore.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After sending a power on pulse the driver has a delay of 100ms
to allow the host controller to boot. Move the delay into
qca_send_power_pulse(), since it is directly related with the
power-on pulse.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are only two types of power pulses 'on' or 'off', pass a boolean
instead of the power pulse 'command'.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Set quirk for wcn3990 to read BD_ADDR from a firmware node property.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During hci down we observed IBS sleep commands are queued in the Tx
buffer and hci_uart_write_work is sending data to the chip which is
not required as the chip is powered off. This patch will disable IBS
and flush the Tx buffer before we turn off the chip.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch will help to stop frame reassembly errors while changing
the baudrate. This is because host send a change baudrate request
command to the chip with 115200 bps, Whereas chip will change their
UART clocks to the enable for new baudrate and sends the response
for the change request command with newer baudrate, On host side
we are still operating in 115200 bps which results of reading garbage
data. Here we are pulling RTS line, so that chip we will wait to send data
to host until host change its baudrate.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
wcn3990 requires a power pulse to turn ON/OFF along with
regulators. Sometimes we are observing the power pulses are sent
out with some time delay, due to queuing these commands. This is
causing synchronization issues with chip, which intern delay the
chip setup or may end up with communication issues.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch add qca_set_bdaddr() to set the device
address for latest Qualcomm Bluetooth chipset wcn3990 and above.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>
As done treewide earlier, this catches several more open-coded
allocation size calculations that were added to the kernel during the
merge window. This performs the following mechanical transformations
using Coccinelle:
kvmalloc(a * b, ...) -> kvmalloc_array(a, b, ...)
kvzalloc(a * b, ...) -> kvcalloc(a, b, ...)
devm_kzalloc(..., a * b, ...) -> devm_kcalloc(..., a, b, ...)
Signed-off-by: Kees Cook <keescook@chromium.org>
