Recently, drbd_recv_header() was changed to potentially
implicitly "unplug" the backend device(s), in case there
is currently nothing to receive.
Be more explicit about it: re-introduce the original drbd_recv_header(),
and introduce a new drbd_recv_header_maybe_unplug() for use by the
receiver "main loop".
Using explicit plugging via blk_start_plug(); blk_finish_plug();
really helps the io-scheduler of the backend with merging requests.
Wrap the receiver "main loop" with such a plug.
Also catch unplug events on the Primary,
and try to propagate.
This is performance relevant. Without this, if the receiving side does
not merge requests, number of IOPS on the peer can me significantly
higher than IOPS on the Primary, and can easily become the bottleneck.
Together, both changes should help to reduce the number of IOPS
as seen on the backend of the receiving side, by increasing
the chance of merging mergable requests, without trading latency
for more throughput.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull misc user access cleanups from Al Viro:
"The first pile is assorted getting rid of cargo-culted access_ok(),
cargo-culted set_fs() and field-by-field copyouts.
The same description applies to a lot of stuff in other branches -
this is just the stuff that didn't fit into a more specific topical
branch"
* 'work.misc-set_fs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Switch flock copyin/copyout primitives to copy_{from,to}_user()
fs/fcntl: return -ESRCH in f_setown when pid/pgid can't be found
fs/fcntl: f_setown, avoid undefined behaviour
fs/fcntl: f_setown, allow returning error
lpfc debugfs: get rid of pointless access_ok()
adb: get rid of pointless access_ok()
isdn: get rid of pointless access_ok()
compat statfs: switch to copy_to_user()
fs/locks: don't mess with the address limit in compat_fcntl64
nfsd_readlink(): switch to vfs_get_link()
drbd: ->sendpage() never needed set_fs()
fs/locks: pass kernel struct flock to fcntl_getlk/setlk
fs: locks: Fix some troubles at kernel-doc comments
We only call blk_queue_bounce for request-based drivers, so stop messing
with it for make_request based drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
drbd does not modify the bi_io_vec of the cloned bio,
so there is no need to clone that part. So bio_clone_fast()
is the better choice.
For bio_clone_fast() we need to specify a bio_set.
We could use fs_bio_set, which bio_clone() uses, or
drbd_md_io_bio_set, which drbd uses for metadata, but it is
generally best to avoid sharing bio_sets unless you can
be certain that there are no interdependencies.
So create a new bio_set, drbd_io_bio_set, and use bio_clone_fast().
Also remove a "XXX cannot fail ???" comment because it definitely
cannot fail - bio_clone_fast() doesn't fail if the GFP flags allow for
sleeping.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch converts bioset_create() to not create a workqueue by
default, so alloctions will never trigger punt_bios_to_rescuer(). It
also introduces a new flag BIOSET_NEED_RESCUER which tells
bioset_create() to preserve the old behavior.
All callers of bioset_create() that are inside block device drivers,
are given the BIOSET_NEED_RESCUER flag.
biosets used by filesystems or other top-level users do not
need rescuing as the bio can never be queued behind other
bios. This includes fs_bio_set, blkdev_dio_pool,
btrfs_bioset, xfs_ioend_bioset, and one allocated by
target_core_iblock.c.
biosets used by md/raid do not need rescuing as
their usage was recently audited and revised to never
risk deadlock.
It is hoped that most, if not all, of the remaining biosets
can end up being the non-rescued version.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Credit-to: Ming Lei <ming.lei@redhat.com> (minor fixes)
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
"flags" arguments are often seen as good API design as they allow
easy extensibility.
bioset_create_nobvec() is implemented internally as a variation in
flags passed to __bioset_create().
To support future extension, make the internal structure part of the
API.
i.e. add a 'flags' argument to bioset_create() and discard
bioset_create_nobvec().
Note that the bio_split allocations in drivers/md/raid* do not need
the bvec mempool - they should have used bioset_create_nobvec().
Suggested-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that we use the proper REQ_OP_WRITE_ZEROES operation everywhere we can
kill this hack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
It seems like DRBD assumes its on the wire TRIM request always zeroes data.
Use that fact to implement REQ_OP_WRITE_ZEROES.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull sched.h split-up from Ingo Molnar:
"The point of these changes is to significantly reduce the
<linux/sched.h> header footprint, to speed up the kernel build and to
have a cleaner header structure.
After these changes the new <linux/sched.h>'s typical preprocessed
size goes down from a previous ~0.68 MB (~22K lines) to ~0.45 MB (~15K
lines), which is around 40% faster to build on typical configs.
Not much changed from the last version (-v2) posted three weeks ago: I
eliminated quirks, backmerged fixes plus I rebased it to an upstream
SHA1 from yesterday that includes most changes queued up in -next plus
all sched.h changes that were pending from Andrew.
I've re-tested the series both on x86 and on cross-arch defconfigs,
and did a bisectability test at a number of random points.
I tried to test as many build configurations as possible, but some
build breakage is probably still left - but it should be mostly
limited to architectures that have no cross-compiler binaries
available on kernel.org, and non-default configurations"
* 'WIP.sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (146 commits)
sched/headers: Clean up <linux/sched.h>
sched/headers: Remove #ifdefs from <linux/sched.h>
sched/headers: Remove the <linux/topology.h> include from <linux/sched.h>
sched/headers, hrtimer: Remove the <linux/wait.h> include from <linux/hrtimer.h>
sched/headers, x86/apic: Remove the <linux/pm.h> header inclusion from <asm/apic.h>
sched/headers, timers: Remove the <linux/sysctl.h> include from <linux/timer.h>
sched/headers: Remove <linux/magic.h> from <linux/sched/task_stack.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/init.h>
sched/core: Remove unused prefetch_stack()
sched/headers: Remove <linux/rculist.h> from <linux/sched.h>
sched/headers: Remove the 'init_pid_ns' prototype from <linux/sched.h>
sched/headers: Remove <linux/signal.h> from <linux/sched.h>
sched/headers: Remove <linux/rwsem.h> from <linux/sched.h>
sched/headers: Remove the runqueue_is_locked() prototype
sched/headers: Remove <linux/sched.h> from <linux/sched/hotplug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/debug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/nohz.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/stat.h>
sched/headers: Remove the <linux/gfp.h> include from <linux/sched.h>
sched/headers: Remove <linux/rtmutex.h> from <linux/sched.h>
...
Pull vfs sendmsg updates from Al Viro:
"More sendmsg work.
This is a fairly separate isolated stuff (there's a continuation
around lustre, but that one was too late to soak in -next), thus the
separate pull request"
* 'work.sendmsg' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ncpfs: switch to sock_sendmsg()
ncpfs: don't mess with manually advancing iovec on send
ncpfs: sendmsg does *not* bugger iovec these days
ceph_tcp_sendpage(): use ITER_BVEC sendmsg
afs_send_pages(): use ITER_BVEC
rds: remove dead code
ceph: switch to sock_recvmsg()
usbip_recv(): switch to sock_recvmsg()
iscsi_target: deal with short writes on the tx side
[nbd] pass iov_iter to nbd_xmit()
[nbd] switch sock_xmit() to sock_{send,recv}msg()
[drbd] use sock_sendmsg()
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull IDR rewrite from Matthew Wilcox:
"The most significant part of the following is the patch to rewrite the
IDR & IDA to be clients of the radix tree. But there's much more,
including an enhancement of the IDA to be significantly more space
efficient, an IDR & IDA test suite, some improvements to the IDR API
(and driver changes to take advantage of those improvements), several
improvements to the radix tree test suite and RCU annotations.
The IDR & IDA rewrite had a good spin in linux-next and Andrew's tree
for most of the last cycle. Coupled with the IDR test suite, I feel
pretty confident that any remaining bugs are quite hard to hit. 0-day
did a great job of watching my git tree and pointing out problems; as
it hit them, I added new test-cases to be sure not to be caught the
same way twice"
Willy goes on to expand a bit on the IDR rewrite rationale:
"The radix tree and the IDR use very similar data structures.
Merging the two codebases lets us share the memory allocation pools,
and results in a net deletion of 500 lines of code. It also opens up
the possibility of exposing more of the features of the radix tree to
users of the IDR (and I have some interesting patches along those
lines waiting for 4.12)
It also shrinks the size of the 'struct idr' from 40 bytes to 24 which
will shrink a fair few data structures that embed an IDR"
* 'idr-4.11' of git://git.infradead.org/users/willy/linux-dax: (32 commits)
radix tree test suite: Add config option for map shift
idr: Add missing __rcu annotations
radix-tree: Fix __rcu annotations
radix-tree: Add rcu_dereference and rcu_assign_pointer calls
radix tree test suite: Run iteration tests for longer
radix tree test suite: Fix split/join memory leaks
radix tree test suite: Fix leaks in regression2.c
radix tree test suite: Fix leaky tests
radix tree test suite: Enable address sanitizer
radix_tree_iter_resume: Fix out of bounds error
radix-tree: Store a pointer to the root in each node
radix-tree: Chain preallocated nodes through ->parent
radix tree test suite: Dial down verbosity with -v
radix tree test suite: Introduce kmalloc_verbose
idr: Return the deleted entry from idr_remove
radix tree test suite: Build separate binaries for some tests
ida: Use exceptional entries for small IDAs
ida: Move ida_bitmap to a percpu variable
Reimplement IDR and IDA using the radix tree
radix-tree: Add radix_tree_iter_delete
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z7AL
-----END PGP SIGNATURE-----
Merge tag 'for-4.11/linus-merge-signed' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
- blk-mq scheduling framework from me and Omar, with a port of the
deadline scheduler for this framework. A port of BFQ from Paolo is in
the works, and should be ready for 4.12.
- Various fixups and improvements to the above scheduling framework
from Omar, Paolo, Bart, me, others.
- Cleanup of the exported sysfs blk-mq data into debugfs, from Omar.
This allows us to export more information that helps debug hangs or
performance issues, without cluttering or abusing the sysfs API.
- Fixes for the sbitmap code, the scalable bitmap code that was
migrated from blk-mq, from Omar.
- Removal of the BLOCK_PC support in struct request, and refactoring of
carrying SCSI payloads in the block layer. This cleans up the code
nicely, and enables us to kill the SCSI specific parts of struct
request, shrinking it down nicely. From Christoph mainly, with help
from Hannes.
- Support for ranged discard requests and discard merging, also from
Christoph.
- Support for OPAL in the block layer, and for NVMe as well. Mainly
from Scott Bauer, with fixes/updates from various others folks.
- Error code fixup for gdrom from Christophe.
- cciss pci irq allocation cleanup from Christoph.
- Making the cdrom device operations read only, from Kees Cook.
- Fixes for duplicate bdi registrations and bdi/queue life time
problems from Jan and Dan.
- Set of fixes and updates for lightnvm, from Matias and Javier.
- A few fixes for nbd from Josef, using idr to name devices and a
workqueue deadlock fix on receive. Also marks Josef as the current
maintainer of nbd.
- Fix from Josef, overwriting queue settings when the number of
hardware queues is updated for a blk-mq device.
- NVMe fix from Keith, ensuring that we don't repeatedly mark and IO
aborted, if we didn't end up aborting it.
- SG gap merging fix from Ming Lei for block.
- Loop fix also from Ming, fixing a race and crash between setting loop
status and IO.
- Two block race fixes from Tahsin, fixing request list iteration and
fixing a race between device registration and udev device add
notifiations.
- Double free fix from cgroup writeback, from Tejun.
- Another double free fix in blkcg, from Hou Tao.
- Partition overflow fix for EFI from Alden Tondettar.
* tag 'for-4.11/linus-merge-signed' of git://git.kernel.dk/linux-block: (156 commits)
nvme: Check for Security send/recv support before issuing commands.
block/sed-opal: allocate struct opal_dev dynamically
block/sed-opal: tone down not supported warnings
block: don't defer flushes on blk-mq + scheduling
blk-mq-sched: ask scheduler for work, if we failed dispatching leftovers
blk-mq: don't special case flush inserts for blk-mq-sched
blk-mq-sched: don't add flushes to the head of requeue queue
blk-mq: have blk_mq_dispatch_rq_list() return if we queued IO or not
block: do not allow updates through sysfs until registration completes
lightnvm: set default lun range when no luns are specified
lightnvm: fix off-by-one error on target initialization
Maintainers: Modify SED list from nvme to block
Move stack parameters for sed_ioctl to prevent oversized stack with CONFIG_KASAN
uapi: sed-opal fix IOW for activate lsp to use correct struct
cdrom: Make device operations read-only
elevator: fix loading wrong elevator type for blk-mq devices
cciss: switch to pci_irq_alloc_vectors
block/loop: fix race between I/O and set_status
blk-mq-sched: don't hold queue_lock when calling exit_icq
block: set make_request_fn manually in blk_mq_update_nr_hw_queues
...
It is a relatively common idiom (8 instances) to first look up an IDR
entry, and then remove it from the tree if it is found, possibly doing
further operations upon the entry afterwards. If we change idr_remove()
to return the removed object, all of these users can save themselves a
walk of the IDR tree.
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
We will want to have struct backing_dev_info allocated separately from
struct request_queue. As the first step add pointer to backing_dev_info
to request_queue and convert all users touching it. No functional
changes in this patch.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
By general sentiment kref_sub() is a bad interface, make it go away.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Don't pass a size larger than iov_len to kernel_sendmsg().
Otherwise it will cause a NULL pointer deref when kernel_sendmsg()
returns with rv < size.
DRBD as external module has been around in the kernel 2.4 days already.
We used to be compatible to 2.4 and very early 2.6 kernels,
we used to use
rv = sock_sendmsg(sock, &msg, iov.iov_len);
then later changed to
rv = kernel_sendmsg(sock, &msg, &iov, 1, size);
when we should have used
rv = kernel_sendmsg(sock, &msg, &iov, 1, iov.iov_len);
tcp_sendmsg() used to totally ignore the size parameter.
57be5bd ip: convert tcp_sendmsg() to iov_iter primitives
changes that, and exposes our long standing error.
Even with this error exposed, to trigger the bug, we would need to have
an environment (config or otherwise) causing us to not use sendpage()
for larger transfers, a failing connection, and have it fail "just at the
right time". Apparently that was unlikely enough for most, so this went
unnoticed for years.
Still, it is known to trigger at least some of these,
and suspected for the others:
[0] http://lists.linbit.com/pipermail/drbd-user/2016-July/023112.html
[1] http://lists.linbit.com/pipermail/drbd-dev/2016-March/003362.html
[2] https://forums.grsecurity.net/viewtopic.php?f=3&t=4546
[3] https://ubuntuforums.org/showthread.php?t=2336150
[4] http://e2.howsolveproblem.com/i/1175162/
This should go into 4.9,
and into all stable branches since and including v4.0,
which is the first to contain the exposing change.
It is correct for all stable branches older than that as well
(which contain the DRBD driver; which is 2.6.33 and up).
It requires a small "conflict" resolution for v4.4 and earlier, with v4.5
we dropped the comment block immediately preceding the kernel_sendmsg().
Fixes: b411b3637f ("The DRBD driver")
Cc: <stable@vger.kernel.org> # 2.6.33.x-
Cc: viro@zeniv.linux.org.uk
Cc: christoph.lechleitner@iteg.at
Cc: wolfgang.glas@iteg.at
Reported-by: Christoph Lechleitner <christoph.lechleitner@iteg.at>
Tested-by: Christoph Lechleitner <christoph.lechleitner@iteg.at>
Signed-off-by: Richard Weinberger <richard@nod.at>
[changed oneliner to be "obvious" without context; more verbose message]
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since commit 63a4cc2486, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.
No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>
This contains various cosmetic fixes ranging from simple typos to
const-ifying, and using booleans properly.
Original commit messages from Fabian's patch set:
drbd: debugfs: constify drbd_version_fops
drbd: use seq_put instead of seq_print where possible
drbd: include linux/uaccess.h instead of asm/uaccess.h
drbd: use const char * const for drbd strings
drbd: kerneldoc warning fix in w_e_end_data_req()
drbd: use unsigned for one bit fields
drbd: use bool for peer is_ states
drbd: fix typo
drbd: use | for bitmask combination
drbd: use true/false for bool
drbd: fix drbd_bm_init() comments
drbd: introduce peer state union
drbd: fix maybe_pull_ahead() locking comments
drbd: use bool for growing
drbd: remove redundant declarations
drbd: replace if/BUG by BUG_ON
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Roland Kammerer <roland.kammerer@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We will support WRITE_SAME, if
* all peers support WRITE_SAME (both in kernel and DRBD version),
* all peer devices support WRITE_SAME
* logical_block_size is identical on all peers.
We may at some point introduce a fallback on the receiving side
for devices/kernels that do not support WRITE_SAME,
by open-coding a submit loop. But not yet.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If during resync we read only zeroes for a range of sectors assume
that these secotors can be discarded on the sync target node.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The intention was to only suspend IO if some normal bitmap operation is
supposed to be locked out, not always. If the bulk operation is flaged
as BM_LOCKED_CHANGE_ALLOWED, we do not need to suspend IO.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
To avoid confusion between REQ_OP_FLUSH, which is handled by
request_fn drivers, and upper layers requesting the block layer
perform a flush sequence along with possibly a WRITE, this patch
renames REQ_FLUSH to REQ_PREFLUSH.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Separate the op from the rq_flag_bits and have drbd
set/get the bio using bio_set_op_attrs/bio_op.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch replaces uses of the long obsolete hash interface with
either shash (for non-SG users) or ahash.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Disconnect should wait for pending bitmap IO.
But if that bitmap IO is not happening, because it is waiting for
pending application IO, and there is no progress, because the fencing
policy suspended application IO because of the disconnect,
then we deadlock.
The bitmap writeout in this case does not care for concurrent
application IO, so there is no point waiting for it.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
lsblk should be able to pick up stacking device driver relations
involving DRBD conveniently.
Even though upstream kernel since 2011 says
"DON'T USE THIS UNLESS YOU'RE ALREADY USING IT."
a new user has been added since (bcache),
which sets the precedences for us to use it as well.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When accessing out meta data area on disk, we double check the
plausibility of the requested sector offsets, and are very noisy about
it if they look suspicious.
During initial read of our "superblock", for "external" meta data,
this triggered because the range estimate returned by
drbd_md_last_sector() was still wrong.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since kernel 3.3, we can use snprintf-style arguments
to create a workqueue.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The intention is to reduce CPU utilization. Recent measurements
unveiled that the current performance bottleneck is CPU utilization
on the receiving node. The asender thread became CPU limited.
One of the main points is to eliminate the idr_for_each_entry() loop
from the sending acks code path.
One exception in that is sending back ping_acks. These stay
in the ack-receiver thread. Otherwise the logic becomes too
complicated for no added value.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This prepares the next patch where the sending on the meta (or
control) socket is moved to a dedicated workqueue.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Instead of using a rwlock for synchronizing state changes across
resources, take the request locks of all resources for global state
changes. Use resources_mutex to serialize global state changes.
This means that taking the request lock of a resource is now enough to
prevent changes of that resource. (Previously, a read lock on the
global state lock was needed as well.)
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Also change the enum values to all-capital letters.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
As generic_make_request() is now able to handle arbitrarily sized bios,
it's no longer necessary for each individual block driver to define its
own ->merge_bvec_fn() callback. Remove every invocation completely.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: drbd-user@lists.linbit.com
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Yehuda Sadeh <yehuda@inktank.com>
Cc: Sage Weil <sage@inktank.com>
Cc: Alex Elder <elder@kernel.org>
Cc: ceph-devel@vger.kernel.org
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Cc: Neil Brown <neilb@suse.de>
Cc: linux-raid@vger.kernel.org
Cc: Christoph Hellwig <hch@infradead.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Acked-by: NeilBrown <neilb@suse.de> (for the 'md' bits)
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
[dpark: also remove ->merge_bvec_fn() in dm-thin as well as
dm-era-target, and resolve merge conflicts]
Signed-off-by: Dongsu Park <dpark@posteo.net>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently, a bdi (backing_dev_info) embeds single wb (bdi_writeback)
and the role of the separation is unclear. For cgroup support for
writeback IOs, a bdi will be updated to host multiple wb's where each
wb serves writeback IOs of a different cgroup on the bdi. To achieve
that, a wb should carry all states necessary for servicing writeback
IOs for a cgroup independently.
This patch moves bdi->state into wb.
* enum bdi_state is renamed to wb_state and the prefix of all enums is
changed from BDI_ to WB_.
* Explicit zeroing of bdi->state is removed without adding zeoring of
wb->state as the whole data structure is zeroed on init anyway.
* As there's still only one bdi_writeback per backing_dev_info, all
uses of bdi->state are mechanically replaced with bdi->wb.state
introducing no behavior changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: drbd-dev@lists.linbit.com
Cc: Neil Brown <neilb@suse.de>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Mempools created for slab caches should use
mempool_create_slab_pool().
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: Jens Axboe <axboe@fb.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Avoid generic netlink calls in other parts of the code base.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Rename local variable 'ds' to 'disk_state' or 'data_size'.
'dgs' to 'digest_size'
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Don't error out with misleading "out of memory"
if the cpu-mask has more bits set than there are CPUs.
Just truncate to nr_cpu_ids implicitly.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
* Add details about pending meta data operations to in_flight_summary.
* Report number of requests waiting for activity log transactions.
* timing details of peer_requests to in_flight_summary.
* FLUSH details
DRBD devides the incoming request stream into "epochs",
in which peers are allowed to re-order writes independendly.
These epochs are separated by P_BARRIER on the replication link.
Such barrier packets, depending on configuration, may cause
the receiving side to drain the lower level device request queues
and call blkdev_issue_flush().
This is known to be an other major source of latency in DRBD.
Track timing details of calls to blkdev_issue_flush(),
and add them to in_flight_summary.
* data socket stats
To be able to diagnose bottlenecks and root causes of "slow" IO on DRBD,
it is useful to see network buffer stats along with the timing details of
requests, peer requests, and meta data IO.
* pending bitmap IO timing details to in_flight_summary.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Add new debugfs hierarchy /sys/kernel/debug/
drbd/
resources/
$resource_name/connections/peer/$volume_number/
$resource_name/volumes/$volume_number/
minors/$minor_number -> ../resources/$resource_name/volumes/$volume_number/
Followup commits will populate this hierarchy with files containing
statistics, diagnostic information and some attribute data.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Track start and submit time of bitmap operations, and
add pending bitmap IO contexts to a new pending_bitmap_io list.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Background resynchronisation does some "side-stepping", or throttles
itself, if it detects application IO activity, and the current resync
rate estimate is above the configured "cmin-rate".
What was not detected: if there is no application IO,
because it blocks on activity log transactions.
Introduce a new atomic_t ap_actlog_cnt, tracking such blocked requests,
and count non-zero as application IO activity.
This counter is exposed at proc_details level 2 and above.
Also make sure to release the currently locked resync extent
if we side-step due to such voluntary throttling.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Adding requests to per-device fifo lists as soon as possible after
allocating them leaves a simple list_first_entry_or_null() to find the
oldest request, regardless what it is still waiting for.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Record (in jiffies) how much time a request spends in which stages.
Followup commits will use and present this additional timing information
so we can better locate and tackle the root causes of latency spikes,
or present the backlog for asynchronous replication.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
For diagnostic purposes, track intent, start time
and latest submit time of meta data IO.
Move separate members from struct drbd_device
into the embeded struct drbd_md_io.
s/md_io_(page|in_use)/md_io.\1/
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
drbd_destroy_device means to give up reference counts
on the connection(s) reachable via the peer_device(s).
It must not do that by iterating via device->resource->connections,
resource and connections may have already been disassociated
by drbd_free_resource, and we'd leak connection refs.
Instead, iterate via device->peer_devices->connection.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Now that we have additional asynchronous kref_get/kref_put
via debugfs, make sure we catch access after free.
Poison struct drbd_device, drbd_connection and drbd_resource
before kfree() with 0xfd, 0xfc, and 0xf2, respectively.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If "dirty" blocks are written to during resync,
that brings them in-sync.
By explicitly requesting write-acks during resync even in protocol != C,
we now can actually respect this.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Get rid of dump_stack() debug statements.
There is no point whatsoever in registering and unregistering a reboot
notifier that doesn't do anything.
The intention was to switch to an "emergency read-only" mode,
so we won't have to resync the full activity log just because
we had been Primary before the reboot.
Once we have that implemented, we may re-introduce the reboot notifier.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This replaces the md_sync_work member of struct drbd_device
by a new MD_SYNC "work bit" in device->flags.
This replaces the resync_start_work member of struct drbd_device
by a new RS_START "work bit" in device->flags.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The recent fix to put_ldev() (correct ordering of access to local_cnt
and state.disk; memory barrier in __drbd_set_state) guarantees
that the cleanup happens exactly once.
However it does not yet guarantee that the cleanup happens from worker
context, the last put_ldev() may still happen from atomic context,
which must not happen: blkdev_put() may sleep.
Fix this by scheduling the cleanup to the worker instead,
using a couple more bits in device->flags and a new helper,
drbd_device_post_work().
Generalized the "resync progress" work to cover these new work bits.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This should reduce latency for such in-DRBD-protocol "pings",
and may help reduce spurious disconnect/reconnect cycles due to
"PingAck did not arrive in time."
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Since the member of drbd_device is called ldev
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Some parts of the code assumed that get_ldev_if_state(device, D_ATTACHING)
is sufficient to access the ldev member of the device object. That was
wrong. ldev may not be there or might be freed at any time if the device
has a disk state of D_ATTACHING.
bm_rw()
Documented that drbd_bm_read() is only called from drbd_adm_attach.
drbd_bm_write() is only called when a reference is held, and it is
documented that a caller has to hold a reference before calling
drbd_bm_write()
drbd_bm_write_page()
Use get_ldev() instead of get_ldev_if_state(device, D_ATTACHING)
drbd_bmio_set_n_write()
No longer use get_ldev_if_state(device, D_ATTACHING). All callers
hold a reference to ldev now.
drbd_bmio_clear_n_write()
All callers where holding a reference of ldev anyways. Remove the
misleading get_ldev_if_state(device, D_ATTACHING)
drbd_reconsider_max_bio_size()
Removed the get_ldev_if_state(device, D_ATTACHING). All callers
now pass a struct drbd_backing_dev* when they have a proper
reference, or a NULL pointer.
Before this fix, the receiver could trigger a NULL pointer
deref when in drbd_reconsider_max_bio_size()
drbd_bump_write_ordering()
Used get_ldev_if_state(device, D_ATTACHING) with the wrong assumption.
Remove it, and allow the caller to pass in a struct drbd_backing_dev*
when the caller knows that accessing this bdev is safe.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Note that I do NOT call __drbd_chk_io_error for failed REQ_DISCARD.
That may be wrong, though, or needs to differ between EOPNOTSUPP and
other errors...
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We plan to use genl_family->parallel_ops = true in the future,
but need to review all possible interactions first.
For now, only selectively drop genl_lock() in drbd_set_role(),
instead serializing on our own internal resource->conf_update mutex.
We now can be promoted/demoted on many resources in parallel,
which may significantly improve cluster failover times
when fencing is required.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Because all administrative requests via genetlink have been globally
serialized via genl_lock(), we used to have one static struct
drbd_config_context "admin context".
Move this on-stack to the respective callback functions.
This will allow us to selectively drop the genl_lock()
(or use genl_family->parallel_ops) in the future.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
In the drbd_thread "infrastructure" functions, only use the resource instead of
the connection. Make the connection field of drbd_thread optional. This will
allow to introduce threads which are not associated with a connection.
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
The new function can flush any work queue, not just the work queue of the data
socket of a connection.
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
drbd_device_work is a work item that has a reference to a device,
while drbd_work is a more generic work item that does not carry
a reference to a device.
All callbacks get a pointer to a drbd_work instance, those callbacks
that expect a drbd_device_work use the container_of macro to get it.
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Also fix drbd_calc_cpu_mask() to spread resources equally over all online cpus
independent of device minor numbers.
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
in drbd_adm_down(), drbd_create_device() and drbd_set_role()
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
The implicit dependency on a variable inside the macro is problematic.
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
With the polymorphic drbd_() macros, we no longer need the connection
specific variants.
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
DRBD was using dev_err() and similar all over the code; instead of having to
write dev_err(disk_to_dev(device->vdisk), ...) to convert a drbd_device into a
kernel device, a DEV macro was used which implicitly references the device
variable. This is terrible; introduce separate drbd_err() and similar macros
with an explicit device parameter instead.
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Let connection->peer_devices point to peer devices; connection->volumes was
pointing to devices.
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
So far, connections and resources always come in pairs, but in the future with
multiple connections per resource, the names will stick with the resources.
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
This allows to access the volumes of a resource by number.
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
In a first step, each resource has exactly one connection, and both objects are
allocated at the same time. The final result will be one resource and zero or
more connections.
Only allow to delete a resource if all its connections are C_STANDALONE.
Stop the worker threads of all connections early enough.
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
In a setup where a device (aka volume) can replicate to multiple peers and one
connection can be shared between multiple devices, we need separate objects to
represent devices on peer nodes and network connections.
As a first step to introduce multiple connections per device, give each
drbd_device object a single drbd_peer_device object which connects it to a
drbd_connection object.
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
sed -i -e 's:all_tconn:connections:g' -e 's:tconn:connection:g'
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
sed -i -e 's:\<drbd_conf\>:drbd_device:g'
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Keep the protocol definitions separate from the kernel code; they are useful in
their own right.
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Move prototype declaration of functions drbdd_init() and drbd_asender()
from drbd/drbd_main.c to header file drbd/drbd_int.h because these
functions are used by more than one file.
This eliminates the following warning in drbd/drbd_receiver.c:
drivers/block/drbd/drbd_receiver.c:4836:5: warning: no previous prototype for ‘drbdd_init’ [-Wmissing-prototypes]
drivers/block/drbd/drbd_receiver.c:5245:5: warning: no previous prototype for ‘drbd_asender’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Mark functions _drbd_send_uuids(), fill_bitmap_rle_bits() and
init_submitter() as static in drbd/drbd_main.c because they are
not used outside this file.
This eliminates the following warnings in drbd/drbd_main.c:
drivers/block/drbd/drbd_main.c:826:5: warning: no previous prototype for ‘_drbd_send_uuids’ [-Wmissing-prototypes]
drivers/block/drbd/drbd_main.c:1070:5: warning: no previous prototype for ‘fill_bitmap_rle_bits’ [-Wmissing-prototypes]
drivers/block/drbd/drbd_main.c:2592:5: warning: no previous prototype for ‘init_submitter’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
This adds a mechanism by which we can advance a bio by an arbitrary
number of bytes without modifying the biovec: bio->bi_iter.bi_bvec_done
indicates the number of bytes completed in the current bvec.
Various driver code still needs to be updated to not refer to the bvec
directly before we can use this for interesting things, like efficient
bio splitting.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: Paul Clements <Paul.Clements@steeleye.com>
Cc: drbd-user@lists.linbit.com
Cc: nbd-general@lists.sourceforge.net
More prep work for immutable biovecs - with immutable bvecs drivers
won't be able to use the biovec directly, they'll need to use helpers
that take into account bio->bi_iter.bi_bvec_done.
This updates callers for the new usage without changing the
implementation yet.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Paul Clements <Paul.Clements@steeleye.com>
Cc: Jim Paris <jim@jtan.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Yehuda Sadeh <yehuda@inktank.com>
Cc: Sage Weil <sage@inktank.com>
Cc: Alex Elder <elder@inktank.com>
Cc: ceph-devel@vger.kernel.org
Cc: Joshua Morris <josh.h.morris@us.ibm.com>
Cc: Philip Kelleher <pjk1939@linux.vnet.ibm.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Cc: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@lsi.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: support@lsi.com
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Guo Chao <yan@linux.vnet.ibm.com>
Cc: Asai Thambi S P <asamymuthupa@micron.com>
Cc: Selvan Mani <smani@micron.com>
Cc: Sam Bradshaw <sbradshaw@micron.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Quoc-Son Anh <quoc-sonx.anh@intel.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Seth Jennings <sjenning@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: "Darrick J. Wong" <darrick.wong@oracle.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jan Kara <jack@suse.cz>
Cc: linux-m68k@lists.linux-m68k.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: drbd-user@lists.linbit.com
Cc: nbd-general@lists.sourceforge.net
Cc: cbe-oss-dev@lists.ozlabs.org
Cc: xen-devel@lists.xensource.com
Cc: virtualization@lists.linux-foundation.org
Cc: linux-raid@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: DL-MPTFusionLinux@lsi.com
Cc: linux-scsi@vger.kernel.org
Cc: devel@driverdev.osuosl.org
Cc: linux-fsdevel@vger.kernel.org
Cc: cluster-devel@redhat.com
Cc: linux-mm@kvack.org
Acked-by: Geoff Levand <geoff@infradead.org>
If we want to iterate over the (as of yet still empty) list in the
cleanup path, we need to initialize the list before the first goto fail.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Allow to change the AL layout with an resize operation. For that
the reisze command gets two new fields: al_stripes and al_stripe_size.
In order to make the operation crash save:
1) Lock out all IO and MD-IO
2) Write the super block with MDF_PRIMARY_IND clear
3) write the bitmap to the new location (all zeros, since
we allow only while connected)
4) Initialize the new AL-area
5) Write the super block with the restored MDF_PRIMARY_IND.
6) Unfreeze all IO
Since the AL-layout has no influence on the protocol, this operation
needs to be beforemed on both sides of a resource (if intended).
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull block driver updates from Jens Axboe:
"It might look big in volume, but when categorized, not a lot of
drivers are touched. The pull request contains:
- mtip32xx fixes from Micron.
- A slew of drbd updates, this time in a nicer series.
- bcache, a flash/ssd caching framework from Kent.
- Fixes for cciss"
* 'for-3.10/drivers' of git://git.kernel.dk/linux-block: (66 commits)
bcache: Use bd_link_disk_holder()
bcache: Allocator cleanup/fixes
cciss: bug fix to prevent cciss from loading in kdump crash kernel
cciss: add cciss_allow_hpsa module parameter
drivers/block/mg_disk.c: add CONFIG_PM_SLEEP to suspend/resume functions
mtip32xx: Workaround for unaligned writes
bcache: Make sure blocksize isn't smaller than device blocksize
bcache: Fix merge_bvec_fn usage for when it modifies the bvm
bcache: Correctly check against BIO_MAX_PAGES
bcache: Hack around stuff that clones up to bi_max_vecs
bcache: Set ra_pages based on backing device's ra_pages
bcache: Take data offset from the bdev superblock.
mtip32xx: mtip32xx: Disable TRIM support
mtip32xx: fix a smatch warning
bcache: Disable broken btree fuzz tester
bcache: Fix a format string overflow
bcache: Fix a minor memory leak on device teardown
bcache: Documentation updates
bcache: Use WARN_ONCE() instead of __WARN()
bcache: Add missing #include <linux/prefetch.h>
...
The value passed is 0 in all but "it can never happen" cases (and those
only in a couple of drivers) *and* it would've been lost on the way
out anyway, even if something tried to pass something meaningful.
Just don't bother.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We forgot to free the disk_conf,
so for each attach/detach cycle we leaked 336 bytes.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Introduced in drbd: always write bitmap on detach,
the bitmap bulk writeout on detach was indicating
it expected exclusive bitmap access.
Where I meant to say: expect no more modifications,
but testing/counting is still allowed.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We used to calculate all on-disk meta data offsets, and then compare
the stored offsets, basically treating them as magic numbers.
Now with the activity log striping, the activity log size is no longer
fixed. We need to first read the super block, then base the activity
log and bitmap offsets on the stored offsets/al stripe settings.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Make it obvious that this value is in units of 512 Byte sectors.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Introduce two new on-disk meta data fields: al_stripes and al_stripe_size_4k
The intended use case is activity log on RAID 0 or similar.
Logically consecutive transactions will advance their on-disk position
by al_stripe_size_4k 4kB (transaction sized) blocks.
Right now, these are still asserted to be the backward compatible
values al_stripes = 1, al_stripe_size_4k = 8 (which amounts to 32kB).
Also introduce a caching member for meta_dev_idx in the in-core
structure: even though it is initially passed in in the rcu-protected
disk_conf structure, it cannot change without a detach/attach cycle.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a comment about our meta data layout variants,
and rename a few defines (e.g. MD_RESERVED_SECT -> MD_128MB_SECT)
to make it clear that they are short hand for fixed constants,
and not arbitrarily to be redefined as one may see fit.
Properly pad struct meta_data_on_disk to 4kB,
and initialize to zero not only the first 512 Byte,
but all of it in drbd_md_sync().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This fixes ASSERT( mdev->state.disk == D_FAILED ) in drivers/block/drbd/drbd_main.c
When we detach from local disk, we let the local refcount hit zero twice.
First, we transition to D_FAILED, so we won't give out new references
to incoming requests; we still may give out *internal* references, though.
Once the refcount hits zero [1] while in D_FAILED, we queue a transition
to D_DISKLESS to our worker. We need to queue it, because we may be in
atomic context when putting the reference.
Once the transition to D_DISKLESS actually happened [2] from worker context,
we don't give out new internal references either.
Between hitting zero the first time [1] and actually transition to
D_DISKLESS [2], there may be a few very short lived internal get/put,
so we may hit zero more than once while being in D_FAILED, or even see a
race where a an internal get_ldev() happened while D_FAILED, but the
corresponding put_ldev() happens just after the transition to D_DISKLESS.
That's why we have the additional test_and_set_bit(GO_DISKLESS,);
and that's why the assert was placed wrong.
Since there was exactly one code path left to drbd_go_diskless(),
and that checks already for D_FAILED, drop that assert,
and fold in the drbd_queue_work().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Smatch complained about it this redundanct check.
The check was introduced in 2006-09-13. On 2007-07-24 the body of the
function was enclosed by get_ldev()/put_ldev() reference counting.
Since then the check is useless and miss leading.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
recent commit
drbd: always write bitmap on detach
introduced a bitmap writeout during detach,
which obviously needs some meta data device to write to.
Unfortunately, that same error path may be taken if we fail to attach,
e.g. due to UUID mismatch, after we changed state to D_ATTACHING,
but before the lower level device pointer is even assigned.
We need to test for presence of mdev->ldev.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we detach due to local read-error (which sets a bit in the bitmap),
stay Primary, and then re-attach (which re-reads the bitmap from disk),
we potentially lost the "out-of-sync" (or, "bad block") information in
the bitmap.
Always (try to) write out the changed bitmap pages before going diskless.
That way, we don't lose the bit for the bad block,
the next resync will fetch it from the peer, and rewrite
it locally, which may result in block reallocation in some
lower layer (or the hardware), and thereby "heal" the bad blocks.
If the bitmap writeout errors out as well, we will (again: try to)
mark the "we need a full sync" bit in our super block,
if it was a READ error; writes are covered by the activity log already.
If that superblock does not make it to disk either, we are sorry.
Maybe we just lost an entire disk or controller (or iSCSI connection),
and there actually are no bad blocks at all, so we don't need to
re-fetch from the peer, there is no "auto-healing" necessary.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Without this, the meta-data gets updates after 5 seconds by the
md_sync_timer. Better to do it immeditaly after a state change.
If the asender detects a network failure, it may take a bit until
the worker processes the according after-conn-state-change work item.
The worker might be blocked in sending something, i.e. it
takes until it gets into its timeout. That is 6 seconds by
default which is longer than the 5 seconds of the md_sync_timer.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If the md_sync_timer triggers a second time,
while the work queued during the first time is still pending,
this could result in list_add() of an already added item,
and corrupt the work item list.
This likely only triggered because of the erroneous
batch-dequeueing of work items fixed with
drbd: dequeue single work items in wait_for_work()
Still, skip queueing if md_sync_work is already queued.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
There is at least the worker context, the receiver context, the context of
receiving netlink packts.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
To avoid confusion with REQ_DISCARD aka TRIM, rename our
"discard concurrent write acks" from P_DISCARD_WRITE to P_SUPERSEDED.
At the same time, rename the drbd request event DISCARD_WRITE
to CONFLICT_RESOLVED. It already triggers both successful completion
or restart of the request, depending on our RQ_POSTPONED flag.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
In 8.4, we may have bios spanning two activity log extents.
Fixup drbd_al_begin_io() and drbd_al_complete_io() to deal with zero sized bios.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If the drbd worker thread is synchronously waiting for some userland
callback, we don't want some casual pageout to block on us.
Have drbd_congested() report congestion in that case.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Aborting local requests (not waiting for completion from the lower level
disk) is dangerous: if the master bio has been completed to upper
layers, data pages may be re-used for other things already.
If local IO is still pending and later completes,
this may cause crashes or corrupt unrelated data.
Only abort local IO if explicitly requested.
Intended use case is a lower level device that turned into a tarpit,
not completing io requests, not even doing error completion.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Sometimes, a lower level block device turns into a tar-pit,
not completing requests at all, not even doing error completion.
We can force-detach from such a tar-pit block device,
either by disk-timeout, or by drbdadm detach --force.
Queueing for retry only from the request destruction path (kref hit 0)
makes it impossible to retry affected read requests from the peer,
until the local IO completion happened, as the locally submitted
bio holds a reference on the drbd request object.
If we can only complete READs when the local completion finally
happens, we would not need to force-detach in the first place.
Instead, queue for retry where we otherwise had done the error completion.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
cherry-picked and adapted from drbd 9 devel branch
The logic for when to get or put a reference is in mod_rq_state().
To not get confused in the freeze/thaw respectively resend/restart
paths, or when cleaning up requests waiting for P_BARRIER_ACK, this
also introduces additional state flags:
RQ_COMPLETION_SUSP, and RQ_EXP_BARR_ACK.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The previous commit causes __drbd_make_request() to always return 0.
Change it to void.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
cherry-picked and adapted from drbd 9 devel branch
DRBD requests (struct drbd_request) are already on the per resource
transfer log list, and carry their epoch number. We do not need to
additionally link them on other ring lists in other structs.
The drbd sender thread can recognize itself when to send a P_BARRIER,
by tracking the currently processed epoch, and how many writes
have been processed for that epoch.
If the epoch of the request to be processed does not match the currently
processed epoch, any writes have been processed in it, a P_BARRIER for
this last processed epoch is send out first.
The new epoch then becomes the currently processed epoch.
To not get stuck in drbd_al_begin_io() waiting for P_BARRIER_ACK,
the sender thread also needs to handle the case when the current
epoch was closed already, but no new requests are queued yet,
and send out P_BARRIER as soon as possible.
This is done by comparing the per resource "current transfer log epoch"
(tconn->current_tle_nr) with the per connection "currently processed
epoch number" (tconn->send.current_epoch_nr), while waiting for
new requests to be processed in wait_for_work().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
cherry-picked and adapted from drbd 9 devel branch
In 8.4, we don't distinguish between "resource work" and "connection
work" yet, we have one worker for both, as we still have only one connection.
We only ever used the "data.work",
no need to keep the "meta.work" around.
Move tconn->data.work to tconn->sender_work.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
cherry-picked and adapted from drbd 9 devel branch
In 8.4, we still use drbd_queue_work_front(),
so in normal operation, we can not dequeue batches,
but only single items.
Still, followup commits will wake the worker
without explicitly queueing a work item,
so up() is replaced by a simple wake_up().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
cherry-picked from drbd 9 devel branch.
In preparation of multiple connections, the "barrier number" or
"epoch number" needs to be tracked per-resource, not per connection.
The sequence number space will not be reset anymore.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Meanwhile, this is used to restart failed READ requests as well.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The buffer 'sc.cpu_mask' is a kernel buffer. If bitmap_parse is used
instead of __bitmap_parse the extra parameter that indicates a kernel
buffer is not needed.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Transfer log epochs, and therefore P_BARRIER packets,
are per resource, not per volume.
We must not associate them with "some random volume".
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
w_restart_write(), run from worker context, calls __drbd_make_request()
and further drbd_al_begin_io(, delegate=true), which then
potentially deadlocks. The previous patch moved a BUG_ON to expose
such call paths, which would now be triggered.
Also, if we call __drbd_make_request() from resource worker context,
like w_restart_write() did, and that should block for whatever reason
(!drbd_state_is_stable(), resource suspended, ...),
we potentially deadlock the whole resource, as the worker
is needed for state changes and other things.
Create a dedicated retry workqueue for this instead.
Also make sure that inc_ap_bio()/dec_ap_bio() are properly paired,
even if do_retry() needs to retry itself,
in case __drbd_make_request() returns != 0.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We send left-over garbage from the previous packet in P_DATA_REPLY and
P_RS_DATA_REPLY packets. That's bad behaviour.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This is necessary since the transfer_log on the sending is also
per tconn.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This is necessary in order to prepare the move of the (receiver side)
epoch list from the device (mdev) to the connection (tconn) objects.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
That is necessary since the whole transfer log is per connection(tconn)
and not per device(mdev).
This bug caused list corruption on the worker list. When a barrier is queued
for sending in the context of one device, another device did not see the
CREATE_BARRIER bit, and queued the same object again -> list corruption.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
* drbd-8.3:
drbd: O_SYNC gives EIO on ramdisks for some kernels (eg. RHEL6).
drbd: send intermediate state change results to the peer
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
* drbd-8.3:
drbd: fix spurious meta data IO "error"
drbd: Fixed a race condition between detach and start of resync
drbd: fix harmless race to not trigger an ASSERT
drbd: Derive sync-UUIDs only from the bitmap-uuid if it is non-zero
drbd: Fixed current UUID generation (regression introduced recently, after 8.3.11)
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The last data-integrity-alg fix made data integrity checking work when the
algorithm was changed for an established connection, but the common case of
configuring the algorithm before connecting was still broken. Fix that.
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
There is no need to overly generalize this function; it only makes the code
harder to understand.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
