Add a dump of the EQ entries headers upon a EQ heartbeat failure.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Ofir Bitton <obitton@habana.ai>
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Future supported ASICs might use the dynamic EQ mechanism with the
firmware, and in that case the EQ size won't be equal to the default
HL_EQ_SIZE_IN_BYTES value.
Add an ASIC property to enable overriding this value.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Ofir Bitton <obitton@habana.ai>
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Currently driver maintain one list for both pending user interrupts
which seeks to wait till CQ reaches it's target value and also the ones
that seeks to get timestamp records when the CQ reaches it's target
value.
This causes delay in handling the waiters which gets higher priority
than the timestamp records.
In order to solve this, let's split the list into two,
one for each case and each one is protected by it's own spinlock.
Waiters will be handled within the interrupt context first,
then the timestamp records will be set.
Freeing the timestamp related memory will be handled in a workqueue.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently we use dynamic allocation inside the irq handler
in order to allocate free node to be used for the free jobs.
This operation is expensive, especially when we deal with large
burst of events records that get released at the same time.
The alternative is to have pre allocated pool of free nodes
and just fetch nodes from this pool at irq handling time instead
of allocating them.
In case the pool becomes full, then the driver will fallback to
dynamic allocations.
As part of the optimization also update the unregister flow
upon re-using a timestamp record, by making the operation much
simpler and quicker. We already have the record in the registration
flow and now we just seek to re-use with different interrupt.
Therefore, no need to look for buffer according to the user handle.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
There is a potential race between user thread seeking to re-use
a timestamp record with new interrupt id, while this record is still
in the middle of interrupt handling and it is about to be freed.
Imagine the driver set the record in_use to 0 and only then fill the
free_node information. This might lead to unpleasant scenario where
the new registration thread detects the record as free to use, and
change the cq buff address. That will cause the free_node to get
the wrong buffer address to put refcount to.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
This is the second patch for applying the eq health check mechanism
which will add support for the interrupt flow for gaudi2 asic.
More info about the interrupt mechanism:
set a dedicated msix for the eq error interrupt, and add
interrupt handler for it.
when FW detects some issue with EQ like EQ_FULL, it'll
raise that interrupt and driver should reset the device.
Driver will inform the FW which msix index to use through
the already existing handshake mechanism which will
send msix info message to fw.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Protect against concurrency of user requesting to register a timestamp
offset (where the driver fills the timestamp when the command submission
has finished executing) to a specific user interrupt ID. The
protection is basically to allow only one timestamp registration
request to be handled at a time.
This is needed because the user can decide to re-use a timestamp
offset (register an already registered offset, to a different
interrupt ID). This means the request will cause the timestamp node to
move from one interrupt list to another interrupt list. In such
scenario, without proper protection, we could end up adding the same
node twice to the interrupts wait lists.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to increase reliability of the event queue interface,
we apply to Gaudi2 the same mechanism we have in Gaudi1.
The extra validation is basically checking that the received
event index matches the expected index.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Decoder abnormal interrupts are for errors and not for completion, so
rename the relevant work and work function to not include 'completion'.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
When the device is in disabled state, the driver isn't suppose to
receive any events from FW. Printing the event type, as part of the
message that was already printed, shall help to get more info if this
unexpected message is received.
Signed-off-by: Tal Cohen <talcohen@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
In order for the user to be aware of unexpected events in Gaudi2 that
aren't assigned to a specific engine, we are adding the handling of
this dedicated interrupt.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
hl_irq_handler_default() is not used and can be removed.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
"eq_base[eq->ci].hdr.ctl" is used directly in a print without a
le32_to_cpu() conversion.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
In order to allow TPC engines to raise an assert, we must expose
the relevant MSIX interrupt to the user so he will configure the engine
correctly. In addition, we implement the corresponding interrupt
handler that will notify the user upon such an event.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
In order for interrupt timestamp to be more accurate we should
capture it during the interrupt handling rather than in threaded
irq context.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
We prefer not to handle the user interrupt job inside the interrupt
context. Instead, use threaded IRQ to handle the user interrupts.
This will allow to avoid disabling interrupts when the user process
registers for a new event and to avoid long handling inside an
interrupt.
Signed-off-by: Tal Cohen <talcohen@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Completion timestamp is taken during the actual command submission
release. As the release happens in a work queue, the timestamp taken
is not accurate. Hence, we will take the timestamp in the interrupt
handler itself while propagating it to the release function.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to support more user interrupt types in the future, we
enumerate the user interrupt type instead of using a boolean.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Now that we have a subsystem for compute accelerators, move the
habanalabs driver to it.
This patch only moves the files and fixes the Makefiles. Future
patches will change the existing code to register to the accel
subsystem and expose the accel device char files instead of the
habanalabs device char files.
Update the MAINTAINERS file to reflect this change.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
