Other cgroup policy like bfq, iocost are lazy-initialized when they are
configured for the first time for the device, but blk-throttle is
initialized unconditionally from blkcg_init_disk().
Delay initialization of blk-throttle as well, to save some cpu and
memory overhead if it's not configured.
Noted that once it's initialized, it can't be destroyed until disk
removal, even if it's disabled.
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20240509121107.3195568-3-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
One the one hand, it's marked EXPERIMENTAL since 2017, and looks like
there are no users since then, and no testers and no developers, it's
just not active at all.
On the other hand, even if the config is disabled, there are still many
fields in throtl_grp and throtl_data and many functions that are only
used for throtl low.
At last, currently blk-throtl is initialized during disk initialization,
and destroyed during disk removal, and it exposes many functions to be
called directly from block layer.
Remove throtl low to make code much more cleaner and follow up work much
easier.
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20240509121107.3195568-2-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In preparation for adding a generic zone append emulation using zone
write plugging, allow device drivers supporting zoned block device to
set a the max_zone_append_sectors queue limit of a device to 0 to
indicate the lack of native support for zone append operations and that
the block layer should emulate these operations using regular write
operations.
blk_queue_max_zone_append_sectors() is modified to allow passing 0 as
the max_zone_append_sectors argument. The function
queue_max_zone_append_sectors() is also modified to ensure that the
minimum of the max_hw_sectors and chunk_sectors limit is used whenever
the max_zone_append_sectors limit is 0. This minimum is consistent with
the value set for the max_zone_append_sectors limit by the function
blk_validate_zoned_limits() when limits for a queue are validated.
The helper functions queue_emulates_zone_append() and
bdev_emulates_zone_append() are added to test if a queue (or block
device) emulates zone append operations.
In order for blk_revalidate_disk_zones() to accept zoned block devices
relying on zone append emulation, the direct check to the
max_zone_append_sectors queue limit of the disk is replaced by a check
using the value returned by queue_max_zone_append_sectors(). Similarly,
queue_zone_append_max_show() is modified to use the same accessor so
that the sysfs attribute advertizes the non-zero limit that will be
used, regardless if it is for native or emulated commands.
For stacking drivers, a top device should not need to care if the
underlying devices have native or emulated zone append operations.
blk_stack_limits() is thus modified to set the top device
max_zone_append_sectors limit using the new accessor
queue_limits_max_zone_append_sectors(). queue_max_zone_append_sectors()
is modified to use this function as well. Stacking drivers that require
zone append emulation, e.g. dm-crypt, can still request this feature by
calling blk_queue_max_zone_append_sectors() with a 0 limit.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Hans Holmberg <hans.holmberg@wdc.com>
Tested-by: Dennis Maisenbacher <dennis.maisenbacher@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240408014128.205141-10-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Convert queue_discard_max_store to use queue_limits_commit_update to
check and update the max_discard_sectors limit and freeze the queue
before doing so to ensure we don't have requests in flight while
changing the limits.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240213073425.1621680-8-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a new max_user_discard_sectors limit that mirrors max_user_sectors
and stores the value that the user manually set. This now allows
updates of the max_hw_discard_sectors to not worry about the user
limit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240213073425.1621680-7-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Convert queue_max_sectors_store to use queue_limits_commit_update to
check and update the max_sectors limit and freeze the queue before
doing so to ensure we don't have requests in flight while changing
the limits.
Note that this removes the previously held queue_lock that doesn't
protect against any other reader or writer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240213073425.1621680-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=YAfp
-----END PGP SIGNATURE-----
Merge tag 'for-6.8/block-2024-01-08' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
"Pretty quiet round this time around. This contains:
- NVMe updates via Keith:
- nvme fabrics spec updates (Guixin, Max)
- nvme target udpates (Guixin, Evan)
- nvme attribute refactoring (Daniel)
- nvme-fc numa fix (Keith)
- MD updates via Song:
- Fix/Cleanup RCU usage from conf->disks[i].rdev (Yu Kuai)
- Fix raid5 hang issue (Junxiao Bi)
- Add Yu Kuai as Reviewer of the md subsystem
- Remove deprecated flavors (Song Liu)
- raid1 read error check support (Li Nan)
- Better handle events off-by-1 case (Alex Lyakas)
- Efficiency improvements for passthrough (Kundan)
- Support for mapping integrity data directly (Keith)
- Zoned write fix (Damien)
- rnbd fixes (Kees, Santosh, Supriti)
- Default to a sane discard size granularity (Christoph)
- Make the default max transfer size naming less confusing
(Christoph)
- Remove support for deprecated host aware zoned model (Christoph)
- Misc fixes (me, Li, Matthew, Min, Ming, Randy, liyouhong, Daniel,
Bart, Christoph)"
* tag 'for-6.8/block-2024-01-08' of git://git.kernel.dk/linux: (78 commits)
block: Treat sequential write preferred zone type as invalid
block: remove disk_clear_zoned
sd: remove the !ZBC && blk_queue_is_zoned case in sd_read_block_characteristics
drivers/block/xen-blkback/common.h: Fix spelling typo in comment
blk-cgroup: fix rcu lockdep warning in blkg_lookup()
blk-cgroup: don't use removal safe list iterators
block: floor the discard granularity to the physical block size
mtd_blkdevs: use the default discard granularity
bcache: use the default discard granularity
zram: use the default discard granularity
null_blk: use the default discard granularity
nbd: use the default discard granularity
ubd: use the default discard granularity
block: default the discard granularity to sector size
bcache: discard_granularity should not be smaller than a sector
block: remove two comments in bio_split_discard
block: rename and document BLK_DEF_MAX_SECTORS
loop: don't abuse BLK_DEF_MAX_SECTORS
aoe: don't abuse BLK_DEF_MAX_SECTORS
null_blk: don't cap max_hw_sectors to BLK_DEF_MAX_SECTORS
...
When zones were first added the SCSI and ATA specs, two different
models were supported (in addition to the drive managed one that
is invisible to the host):
- host managed where non-conventional zones there is strict requirement
to write at the write pointer, or else an error is returned
- host aware where a write point is maintained if writes always happen
at it, otherwise it is left in an under-defined state and the
sequential write preferred zones behave like conventional zones
(probably very badly performing ones, though)
Not surprisingly this lukewarm model didn't prove to be very useful and
was finally removed from the ZBC and SBC specs (NVMe never implemented
it). Due to to the easily disappearing write pointer host software
could never rely on the write pointer to actually be useful for say
recovery.
Fortunately only a few HDD prototypes shipped using this model which
never made it to mass production. Drop the support before it is too
late. Note that any such host aware prototype HDD can still be used
with Linux as we'll now treat it as a conventional HDD.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20231217165359.604246-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It is nontrivial to derive the role of the two attribute groups in source
file block/blk-sysfs.c. Hence add a comment that explains their roles. See
also commit 6d85ebf95c ("blk-sysfs: add a new attr_group for blk_mq").
Cc: Christoph Hellwig <hch@lst.de>
Cc: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20231128194019.72762-1-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently the write_cache attribute allows enabling the QUEUE_FLAG_WC
flag on devices that never claimed the capability.
Fix that by adding a QUEUE_FLAG_HW_WC flag that is set by
blk_queue_write_cache and guards re-enabling the cache through sysfs.
Note that any rescan that calls blk_queue_write_cache will still
re-enable the write cache as in the current code.
Fixes: 93e9d8e836 ("block: add ability to flag write back caching on a device")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230707094239.107968-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Get rid of the local queue_wc_store variable and handling setting and
clearing the QUEUE_FLAG_WC flag diretly instead the if / else if.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230707094239.107968-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently wbt sysfs entry is created for bio based device, and wbt can
be enabled for such device through sysfs while it doesn't make sense
because wbt can only work for rq based device. In the meantime, there
are other similar sysfs entries.
Fix this by adding a new attr_group for blk_mq, and sysfs entries will
only be created when the device is rq based.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230527010644.647900-6-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
sysfs entry /sys/block/[device]/queue/wbt_lat_usec will be created even
if CONFIG_BLK_WBT is disabled, while read and write will always fail.
It doesn't make sense to create a sysfs entry that can't be accessed,
so don't create such entry.
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230527010644.647900-2-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
block/blk-mq.h needs various definitions from <linux/blk-mq.h>,
include it there instead of relying on the source files to include
both.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20230413064057.707578-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
io_uring provides the only way user space can poll completions, and that
always sets BLK_POLL_NOSLEEP. This effectively makes hybrid polling dead
code, so remove it and everything supporting it.
Hybrid polling was effectively killed off with 9650b453a3, "block:
ignore RWF_HIPRI hint for sync dio", but still potentially reachable
through io_uring until d729cf9acb, "io_uring: don't sleep when
polling for I/O", but hybrid polling probably should not have been
reachable through that async interface from the beginning.
Fixes: 9650b453a3 ("block: ignore RWF_HIPRI hint for sync dio")
Fixes: d729cf9acb ("io_uring: don't sleep when polling for I/O")
Signed-off-by: Keith Busch <kbusch@kernel.org>
Link: https://lore.kernel.org/r/20230320194926.3353144-1-kbusch@meta.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since commit ee6d3dd4ed ("driver core: make kobj_type constant.")
the driver core allows the usage of const struct kobj_type.
Take advantage of this to constify the structure definitions to prevent
modification at runtime.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20230208-kobj_type-block-v1-1-0b3eafd7d983@weissschuh.net
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A large part of blk-wbt.h is only used in blk-wbt.c, so move it there.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20230203150400.3199230-11-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass a gendisk to wbt_init to prepare for phasing out usage of the
request_queue in the blk-cgroup code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andreas Herrmann <aherrmann@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20230203150400.3199230-10-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass a gendisk to wbt_enable_default and wbt_disable_default to
prepare for phasing out usage of the request_queue in the blk-cgroup
code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andreas Herrmann <aherrmann@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20230203150400.3199230-9-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The user can set the max_sectors limit to any valid value via sysfs
/sys/block/<dev>/queue/max_sectors_kb attribute. If the device limits
are ever rescanned, though, the limit reverts back to the potentially
artificially low BLK_DEF_MAX_SECTORS value.
Preserve the user's setting as the max_sectors limit as long as it's
valid. The user can reset back to defaults by writing 0 to the sysfs
file.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20230105205146.3610282-3-kbusch@meta.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The kobject embedded into the request_queue is used for the queue
directory in sysfs, but that is a child of the gendisks directory and is
intimately tied to it. Move this kobject to the gendisk and use a
refcount_t in the request_queue for the actual request_queue refcounting
that is completely unrelated to the device model.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20221114042637.1009333-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_register_queue fails to handle errors from blk_mq_sysfs_register,
leaks various resources on errors and accidentally sets queue refs percpu
refcount to percpu mode on kobject_add failure. Fix all that by
properly unwinding on errors.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20221114042637.1009333-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Split the debugfs removal from blk_unregister_queue into a helper so that
the it can be reused for blk_register_queue error handling.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20221114042637.1009333-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Prepare for changes to the block layer sysfs handling by passing the
readily available gendisk to blk_crypto_sysfs_{,un}register.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20221114042637.1009333-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All I/O submissions have fairly similar latencies, and a tagset-wide
quiesce is a fairly common operation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Chao Leng <lengchao@huawei.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20221101150050.3510-12-hch@lst.de
[axboe: fix whitespace]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently, if wbt is initialized and then disabled by
wbt_disable_default(), sysfs will still show valid wbt_lat_usec, which
will confuse users that wbt is still enabled.
This patch shows wbt_lat_usec as zero if it's disabled.
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reported-and-tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20221019121518.3865235-5-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass the gendisk to blk_throtl_register_queue as part of moving the
blk-cgroup infrastructure to be gendisk based.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andreas Herrmann <aherrmann@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20220921180501.1539876-14-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Only non-passthrough requests are split by the block layer and use the
->bio_split bio_set. Move it from the request_queue to the gendisk.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220727162300.3089193-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the zone related fields that are currently stored in
struct request_queue to struct gendisk as these are part of the highlevel
block layer API and are only used for non-passthrough I/O that requires
the gendisk.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220706070350.1703384-17-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Always use the bdev based helpers instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220706070350.1703384-10-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The zone bitmaps are only used for non-passthrough I/O, so free them as
soon as the disk is released.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220706070350.1703384-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Lift setting disk->ia_ranges from disk_register_independent_access_ranges
into disk_set_independent_access_ranges, and make the behavior the same
for the registered vs non-registered queue cases.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Link: https://lore.kernel.org/r/20220629062013.1331068-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass a gendisk to the sysfs register/unregister functions and give
them descriptive names. Also move the unregistration helper next
to the one doing the registration.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220628171850.1313069-7-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Set up the default_groups for blk_queue_ktype instead of manually calling
sysfs_create_group.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220628171850.1313069-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
kobject_add already adds a reference to the parent that is dropped
on deletion, so don't bother grabbing another one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220628171850.1313069-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add the trace attributes to the default gendisk attributes, just like
we already do for partitions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220628171850.1313069-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Set the queue dying flag and call blk_mq_exit_queue from del_gendisk for
all disks that do not have separately allocated queues, and thus remove
the need to call blk_cleanup_queue for them.
Rename blk_cleanup_disk to blk_mq_destroy_queue to make it clear that
this function is intended only for separately allocated blk-mq queues.
This saves an extra queue freeze for devices without a separately
allocated queue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20220619060552.1850436-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use ida_alloc()/ida_free() instead of
ida_simple_get()/ida_simple_remove().
The latter is deprecated and more verbose.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Reviewed-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20220615081816.4342-1-liubo03@inspur.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
User space may want to know how to align their buffers to avoid
bouncing. Export the queue attribute.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220610195830.3574005-4-kbusch@fb.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The block debugfs files are created in blk_register_queue, which is
called by add_disk and use a naming scheme based on the disk_name.
After del_gendisk returns that name can be reused and thus we must not
leave these debugfs files around, otherwise the kernel is unhappy
and spews messages like:
Directory XXXXX with parent 'block' already present!
and the newly created devices will not have working debugfs files.
Move the unregistration to blk_unregister_queue instead (which matches
the sysfs unregistration) to make sure the debugfs life time rules match
those of the disk name.
As part of the move also make sure the whole debugfs unregistration is
inside a single debugfs_mutex critical section.
Note that this breaks blktests block/002, which checks that the debugfs
directory has not been removed while blktests is running, but that
particular check should simply be removed from the test case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220614074827.458955-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Various places like I/O schedulers or the QOS infrastructure try to
register debugfs files on demans, which can race with creating and
removing the main queue debugfs directory. Use the existing
debugfs_mutex to serialize all debugfs operations that rely on
q->debugfs_dir or the directories hanging off it.
To make the teardown code a little simpler declare all debugfs dentry
pointers and not just the main one uncoditionally in blkdev.h.
Move debugfs_mutex next to the dentries that it protects and document
what it is used for.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220614074827.458955-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This series consists of the usual driver updates (qla2xxx, pm8001,
libsas, smartpqi, scsi_debug, lpfc, iscsi, mpi3mr) plus minor updates
and bug fixes. The high blast radius core update is the removal of
write same, which affects block and several non-SCSI devices. The
other big change, which is more local, is the removal of the SCSI
pointer.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYjzDQyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQMYAQDEWUGV
6U0+736AHVtOfiMNfiRN79B1HfXVoHvemnPcTwD/UlndwFfy/3GGOtoZmqEpc73J
Ec1HDuUCE18H1H2QAh0=
=/Ty9
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This series consists of the usual driver updates (qla2xxx, pm8001,
libsas, smartpqi, scsi_debug, lpfc, iscsi, mpi3mr) plus minor updates
and bug fixes.
The high blast radius core update is the removal of write same, which
affects block and several non-SCSI devices. The other big change,
which is more local, is the removal of the SCSI pointer"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (281 commits)
scsi: scsi_ioctl: Drop needless assignment in sg_io()
scsi: bsg: Drop needless assignment in scsi_bsg_sg_io_fn()
scsi: lpfc: Copyright updates for 14.2.0.0 patches
scsi: lpfc: Update lpfc version to 14.2.0.0
scsi: lpfc: SLI path split: Refactor BSG paths
scsi: lpfc: SLI path split: Refactor Abort paths
scsi: lpfc: SLI path split: Refactor SCSI paths
scsi: lpfc: SLI path split: Refactor CT paths
scsi: lpfc: SLI path split: Refactor misc ELS paths
scsi: lpfc: SLI path split: Refactor VMID paths
scsi: lpfc: SLI path split: Refactor FDISC paths
scsi: lpfc: SLI path split: Refactor LS_RJT paths
scsi: lpfc: SLI path split: Refactor LS_ACC paths
scsi: lpfc: SLI path split: Refactor the RSCN/SCR/RDF/EDC/FARPR paths
scsi: lpfc: SLI path split: Refactor PLOGI/PRLI/ADISC/LOGO paths
scsi: lpfc: SLI path split: Refactor base ELS paths and the FLOGI path
scsi: lpfc: SLI path split: Introduce lpfc_prep_wqe
scsi: lpfc: SLI path split: Refactor fast and slow paths to native SLI4
scsi: lpfc: SLI path split: Refactor lpfc_iocbq
scsi: lpfc: Use kcalloc()
...
There can't be file system I/O in disk_release(), so move the call to
blk_exit_queue() there, preparing to have the teardown of file system I/O
only functionality in one place, when the gendisk that is needed for it
is torn down.
We still need to freeze queue here since the request is freed after the
bio is completed and passthrough request rely on scheduler tags as well.
The disk can be released before or after queue is cleaned up, and we have
to free the scheduler request pool before blk_cleanup_queue returns,
while the static request pool has to be freed before exiting the
I/O scheduler.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
[hch: rebased, updated the commit log]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220308055200.735835-13-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
After blk_cleanup_queue() returns, disk may not be released yet, so
probably bio may still be submitted and ->q_usage_counter may be
touched, so far this way seems safe, but not good from API's viewpoint.
Move the release q_usage_counter into blk_queue_release().
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220308055200.735835-12-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blkcg works on FS bio level, so it is reasonable to make both blkcg and
gendisk sharing same lifetime. Meantime there won't be any FS IO when
releasing disk, so safe to move blkcg initialization/destroy into disk
allocation/release handler
Long term, we can move blkcg into gendisk completely.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20220308055200.735835-10-hch@lst.de
[axboe: fixup missing blk-cgroup.h include]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add sysfs files that expose the inline encryption capabilities of
request queues:
/sys/block/$disk/queue/crypto/max_dun_bits
/sys/block/$disk/queue/crypto/modes/$mode
/sys/block/$disk/queue/crypto/num_keyslots
Userspace can use these new files to decide what encryption settings to
use, or whether to use inline encryption at all. This also brings the
crypto capabilities in line with the other queue properties, which are
already discoverable via the queue directory in sysfs.
Design notes:
- Place the new files in a new subdirectory "crypto" to group them
together and to avoid complicating the main "queue" directory. This
also makes it possible to replace "crypto" with a symlink later if
we ever make the blk_crypto_profiles into real kobjects (see below).
- It was necessary to define a new kobject that corresponds to the
crypto subdirectory. For now, this kobject just contains a pointer
to the blk_crypto_profile. Note that multiple queues (and hence
multiple such kobjects) may refer to the same blk_crypto_profile.
An alternative design would more closely match the current kernel
data structures: the blk_crypto_profile could be a kobject itself,
located directly under the host controller device's kobject, while
/sys/block/$disk/queue/crypto would be a symlink to it.
I decided not to do that for now because it would require a lot more
changes, such as no longer embedding blk_crypto_profile in other
structures, and also because I'm not sure we can rule out moving the
crypto capabilities into 'struct queue_limits' in the future. (Even
if multiple queues share the same crypto engine, maybe the supported
data unit sizes could differ due to other queue properties.) It
would also still be possible to switch to that design later without
breaking userspace, by replacing the directory with a symlink.
- Use "max_dun_bits" instead of "max_dun_bytes". Currently, the
kernel internally stores this value in bytes, but that's an
implementation detail. It probably makes more sense to talk about
this value in bits, and choosing bits is more future-proof.
- "modes" is a sub-subdirectory, since there may be multiple supported
crypto modes, sysfs is supposed to have one value per file, and it
makes sense to group all the mode files together.
- Each mode had to be named. The crypto API names like "xts(aes)" are
not appropriate because they don't specify the key size. Therefore,
I assigned new names. The exact names chosen are arbitrary, but
they happen to match the names used in log messages in fs/crypto/.
- The "num_keyslots" file is a bit different from the others in that
it is only useful to know for performance reasons. However, it's
included as it can still be useful. For example, a user might not
want to use inline encryption if there aren't very many keyslots.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20220124215938.2769-4-ebiggers@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
kobjects aren't supposed to be deleted before their child kobjects are
deleted. Apparently this is usually benign; however, a WARN will be
triggered if one of the child kobjects has a named attribute group:
sysfs group 'modes' not found for kobject 'crypto'
WARNING: CPU: 0 PID: 1 at fs/sysfs/group.c:278 sysfs_remove_group+0x72/0x80
...
Call Trace:
sysfs_remove_groups+0x29/0x40 fs/sysfs/group.c:312
__kobject_del+0x20/0x80 lib/kobject.c:611
kobject_cleanup+0xa4/0x140 lib/kobject.c:696
kobject_release lib/kobject.c:736 [inline]
kref_put include/linux/kref.h:65 [inline]
kobject_put+0x53/0x70 lib/kobject.c:753
blk_crypto_sysfs_unregister+0x10/0x20 block/blk-crypto-sysfs.c:159
blk_unregister_queue+0xb0/0x110 block/blk-sysfs.c:962
del_gendisk+0x117/0x250 block/genhd.c:610
Fix this by moving the kobject_del() and the corresponding
kobject_uevent() to the correct place.
Fixes: 2c2086afc2 ("block: Protect less code with sysfs_lock in blk_{un,}register_queue()")
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220124215938.2769-3-ebiggers@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Make elv_unregister_queue() a no-op if q->elevator is NULL or is not
registered.
This simplifies the existing callers, as well as the future caller in
the error path of blk_register_queue().
Also don't bother checking whether q is NULL, since it never is.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220124215938.2769-2-ebiggers@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
No more users of REQ_OP_WRITE_SAME or drivers implementing it are left,
so remove the infrastructure.
[mkp: fold in and tweak sysfs reporting fix]
Link: https://lore.kernel.org/r/20220209082828.2629273-8-hch@lst.de
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Partition include/linux/blk-cgroup.h into two parts: one is public part,
the other is block layer private part.
Suggested by Christoph Hellwig.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220211101149.2368042-4-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_stat_disable_accounting() is added in commit 68497092bd
("block: make queue stat accounting a reference"), and called in
kyber_exit_sched().
So we have to free q->stats after elevator is unloaded from
blk_exit_queue() in blk_release_queue(). Otherwise kernel panic
is caused.
Fixes: 68497092bd ("block: make queue stat accounting a reference")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20211221040436.1333880-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In case of BLK_MQ_F_BLOCKING, per-hctx srcu is used to protect dispatch
critical area. However, this srcu instance stays at the end of hctx, and
it often takes standalone cacheline, often cold.
Inside srcu_read_lock() and srcu_read_unlock(), WRITE is always done on
the indirect percpu variable which is allocated from heap instead of
being embedded, srcu->srcu_idx is read only in srcu_read_lock(). It
doesn't matter if srcu structure stays in hctx or request queue.
So switch to per-request-queue srcu for protecting dispatch, and this
way simplifies quiesce a lot, not mention quiesce is always done on the
request queue wide.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20211203131534.3668411-3-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Open code elevator_exit in it's only caller, and rename __elevator_exit to
elevator_exit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20211123185312.1432157-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is essentially never used, yet it's about 1/3rd of the total
queue size. Allocate it when needed, and don't embed it in the queue.
Kill the queue flag for this while at it, since we can just check the
assigned pointer now.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The Concurrent Positioning Ranges VPD page (for SCSI) and data log page
(for ATA) contain parameters describing the set of contiguous LBAs that
can be served independently by a single LUN multi-actuator hard-disk.
Similarly, a logically defined block device composed of multiple disks
can in some cases execute requests directed at different sector ranges
in parallel. A dm-linear device aggregating 2 block devices together is
an example.
This patch implements support for exposing a block device independent
access ranges to the user through sysfs to allow optimizing device
accesses to increase performance.
To describe the set of independent sector ranges of a device (actuators
of a multi-actuator HDDs or table entries of a dm-linear device),
The type struct blk_independent_access_ranges is introduced. This
structure describes the sector ranges using an array of
struct blk_independent_access_range structures. This range structure
defines the start sector and number of sectors of the access range.
The ranges in the array cannot overlap and must contain all sectors
within the device capacity.
The function disk_set_independent_access_ranges() allows a device
driver to signal to the block layer that a device has multiple
independent access ranges. In this case, a struct
blk_independent_access_ranges is attached to the device request queue
by the function disk_set_independent_access_ranges(). The function
disk_alloc_independent_access_ranges() is provided for drivers to
allocate this structure.
struct blk_independent_access_ranges contains kobjects (struct kobject)
to expose to the user through sysfs the set of independent access ranges
supported by a device. When the device is initialized, sysfs
registration of the ranges information is done from blk_register_queue()
using the block layer internal function
disk_register_independent_access_ranges(). If a driver calls
disk_set_independent_access_ranges() for a registered queue, e.g. when a
device is revalidated, disk_set_independent_access_ranges() will execute
disk_register_independent_access_ranges() to update the sysfs attribute
files. The sysfs file structure created starts from the
independent_access_ranges sub-directory and contains the start sector
and number of sectors of each range, with the information for each range
grouped in numbered sub-directories.
E.g. for a dual actuator HDD, the user sees:
$ tree /sys/block/sdk/queue/independent_access_ranges/
/sys/block/sdk/queue/independent_access_ranges/
|-- 0
| |-- nr_sectors
| `-- sector
`-- 1
|-- nr_sectors
`-- sector
For a regular device with a single access range, the
independent_access_ranges sysfs directory does not exist.
Device revalidation may lead to changes to this structure and to the
attribute values. When manipulated, the queue sysfs_lock and
sysfs_dir_lock mutexes are held for atomicity, similarly to how the
blk-mq and elevator sysfs queue sub-directories are protected.
The code related to the management of independent access ranges is
added in the new file block/blk-ia-ranges.c.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Link: https://lore.kernel.org/r/20211027022223.183838-2-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The poll attribute is a historic artefact from before when we had
explicit poll queues that require driver specific configuration.
Just print a warning when writing to the attribute.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Tested-by: Mark Wunderlich <mark.wunderlich@intel.com>
Link: https://lore.kernel.org/r/20211012111226.760968-16-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Even if no policies are defined, we spend ~2% of the total IO time
checking. Move the fast path inline.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ensure that all the sysfs bits are set up before bdev_add is called,
as that will make the upcomding error handling much easier. However
this means the call to disk_update_readahead has to be split as that
requires a bdi. Also remove various sanity checks that don't make
sense now that blk_register_queue only has a single caller.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210818144542.19305-7-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Replace the magic lookup through the kobject tree with an explicit
backpointer, given that the device model links are set up and torn
down at times when I/O is still possible, leading to potential
NULL or invalid pointer dereferences.
Fixes: edb0872f44 ("block: move the bdi from the request_queue to the gendisk")
Reported-by: syzbot <syzbot+aa0801b6b32dca9dda82@syzkaller.appspotmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Sven Schnelle <svens@linux.ibm.com>
Link: https://lore.kernel.org/r/20210816134624.GA24234@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The backing device information only makes sense for file system I/O,
and thus belongs into the gendisk and not the lower level request_queue
structure. Move it there.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20210809141744.1203023-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
.. and rename the function to disk_update_readahead. This is in
preparation for moving the BDI from the request_queue to the gendisk.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20210809141744.1203023-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Mark queue init done when everything is done well in blk_register_queue(),
so that wbt_enable_default() can be run quickly without any RCU period
involved since adding rq qos requires to freeze queue.
Also no any side effect by delaying to mark queue init done.
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Link: https://lore.kernel.org/r/20210609015822.103433-3-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This entry will expose the bio vector alignment mask for a specific
block device.
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20210405132012.12504-1-mgurtovoy@nvidia.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
QUEUE_FLAG_POLL flag will be cleared when turning off 'io_poll', while
at that moment there may be IOs stuck in hw queue uncompleted. The
following polling routine won't help reap these IOs, since blk_poll()
will return immediately because of cleared QUEUE_FLAG_POLL flag. Thus
these IOs will hang until they finnaly time out. The hang out can be
observed by 'fio --engine=io_uring iodepth=1', while turning off
'io_poll' at the same time.
To fix this, freeze and flush the request queue first when turning off
'io_poll'.
Signed-off-by: Jeffle Xu <jefflexu@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Per ZBC and ZAC specifications, host-managed SMR hard-disks mandate that
all writes into sequential write required zones be aligned to the device
physical block size. However, NVMe ZNS does not have this constraint and
allows write operations into sequential zones to be aligned to the
device logical block size. This inconsistency does not help with
software portability across device types.
To solve this, introduce the zone_write_granularity queue limit to
indicate the alignment constraint, in bytes, of write operations into
zones of a zoned block device. This new limit is exported as a
read-only sysfs queue attribute and the helper
blk_queue_zone_write_granularity() introduced for drivers to set this
limit.
The function blk_queue_set_zoned() is modified to set this new limit to
the device logical block size by default. NVMe ZNS devices as well as
zoned nullb devices use this default value as is. The scsi disk driver
is modified to execute the blk_queue_zone_write_granularity() helper to
set the zone write granularity of host-managed SMR disks to the disk
physical block size.
The accessor functions queue_zone_write_granularity() and
bdev_zone_write_granularity() are also introduced.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@edc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_exit_queue will free elevator_data, while blk_mq_run_work_fn
will access it. Move cancel of hctx->run_work to the front of
blk_exit_queue to avoid use-after-free.
Fixes: 1b97871b50 ("blk-mq: move cancel of hctx->run_work into blk_mq_hw_sysfs_release")
Signed-off-by: Yang Yang <yang.yang@vivo.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since whole elevator register is protectd by sysfs_lock, we
don't need extras 'has_elevator'. Just use q->elevator directly.
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We will register debugfs for scheduler no matter whether it have
defined callback funciton .exit_sched. So, blk_mq_exit_sched()
is always needed to unregister debugfs. Also, q->elevator should
be set as NULL after exiting scheduler.
For now, since all register scheduler have defined .exit_sched,
it will not cause any actual problem. But It will be more reasonable
to do this change.
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The BDI_CAP_STABLE_WRITES is one of the few bits of information in the
backing_dev_info shared between the block drivers and the writeback code.
To help untangling the dependency replace it with a queue flag and a
superblock flag derived from it. This also helps with the case of e.g.
a file system requiring stable writes due to its own checksumming, but
not forcing it on other users of the block device like the swap code.
One downside is that we an't support the stable_pages_required bdi
attribute in sysfs anymore. It is replaced with a queue attribute which
also is writable for easier testing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Drivers shouldn't really mess with the readahead size, as that is a VM
concept. Instead set it based on the optimal I/O size by lifting the
algorithm from the md driver when registering the disk. Also set
bdi->io_pages there as well by applying the same scheme based on
max_sectors. To ensure the limits work well for stacking drivers a
new helper is added to update the readahead limits from the block
limits, which is also called from disk_stack_limits.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Switch to the naming used by the other entries so that we can use the
QUEUE_RW_ENTRY helper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add two helpers macros to avoid boilerplate code for the queue sysfs
entries.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a new max_active zones definition in the sysfs documentation.
This definition will be common for all devices utilizing the zoned block
device support in the kernel.
Export max_active_zones according to this new definition for NVMe Zoned
Namespace devices, ZAC ATA devices (which are treated as SCSI devices by
the kernel), and ZBC SCSI devices.
Add the new max_active_zones member to struct request_queue, rather
than as a queue limit, since this property cannot be split across stacking
drivers.
For SCSI devices, even though max active zones is not part of the ZBC/ZAC
spec, export max_active_zones as 0, signifying "no limit".
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Javier González <javier@javigon.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a new max_open_zones definition in the sysfs documentation.
This definition will be common for all devices utilizing the zoned block
device support in the kernel.
Export max open zones according to this new definition for NVMe Zoned
Namespace devices, ZAC ATA devices (which are treated as SCSI devices by
the kernel), and ZBC SCSI devices.
Add the new max_open_zones member to struct request_queue, rather
than as a queue limit, since this property cannot be split across stacking
drivers.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Javier González <javier@javigon.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We were only creating the request_queue debugfs_dir only
for make_request block drivers (multiqueue), but never for
request-based block drivers. We did this as we were only
creating non-blktrace additional debugfs files on that directory
for make_request drivers. However, since blktrace *always* creates
that directory anyway, we special-case the use of that directory
on blktrace. Other than this being an eye-sore, this exposes
request-based block drivers to the same debugfs fragile
race that used to exist with make_request block drivers
where if we start adding files onto that directory we can later
run a race with a double removal of dentries on the directory
if we don't deal with this carefully on blktrace.
Instead, just simplify things by always creating the request_queue
debugfs_dir on request_queue registration. Rename the mutex also to
reflect the fact that this is used outside of the blktrace context.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit dc9edc44de ("block: Fix a blk_exit_rl() regression") merged on
v4.12 moved the work behind blk_release_queue() into a workqueue after a
splat floated around which indicated some work on blk_release_queue()
could sleep in blk_exit_rl(). This splat would be possible when a driver
called blk_put_queue() or blk_cleanup_queue() (which calls blk_put_queue()
as its final call) from an atomic context.
blk_put_queue() decrements the refcount for the request_queue kobject, and
upon reaching 0 blk_release_queue() is called. Although blk_exit_rl() is
now removed through commit db6d995235 ("block: remove request_list code")
on v5.0, we reserve the right to be able to sleep within
blk_release_queue() context.
The last reference for the request_queue must not be called from atomic
context. *When* the last reference to the request_queue reaches 0 varies,
and so let's take the opportunity to document when that is expected to
happen and also document the context of the related calls as best as
possible so we can avoid future issues, and with the hopes that the
synchronous request_queue removal sticks.
We revert back to synchronous request_queue removal because asynchronous
removal creates a regression with expected userspace interaction with
several drivers. An example is when removing the loopback driver, one
uses ioctls from userspace to do so, but upon return and if successful,
one expects the device to be removed. Likewise if one races to add another
device the new one may not be added as it is still being removed. This was
expected behavior before and it now fails as the device is still present
and busy still. Moving to asynchronous request_queue removal could have
broken many scripts which relied on the removal to have been completed if
there was no error. Document this expectation as well so that this
doesn't regress userspace again.
Using asynchronous request_queue removal however has helped us find
other bugs. In the future we can test what could break with this
arrangement by enabling CONFIG_DEBUG_KOBJECT_RELEASE.
While at it, update the docs with the context expectations for the
request_queue / gendisk refcount decrement, and make these
expectations explicit by using might_sleep().
Fixes: dc9edc44de ("block: Fix a blk_exit_rl() regression")
Suggested-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Nicolai Stange <nstange@suse.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: yu kuai <yukuai3@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Define REQ_OP_ZONE_APPEND to append-write sectors to a zone of a zoned
block device. This is a no-merge write operation.
A zone append write BIO must:
* Target a zoned block device
* Have a sector position indicating the start sector of the target zone
* The target zone must be a sequential write zone
* The BIO must not cross a zone boundary
* The BIO size must not be split to ensure that a single range of LBAs
is written with a single command.
Implement these checks in generic_make_request_checks() using the
helper function blk_check_zone_append(). To avoid write append BIO
splitting, introduce the new max_zone_append_sectors queue limit
attribute and ensure that a BIO size is always lower than this limit.
Export this new limit through sysfs and check these limits in bio_full().
Also when a LLDD can't dispatch a request to a specific zone, it
will return BLK_STS_ZONE_RESOURCE indicating this request needs to
be delayed, e.g. because the zone it will be dispatched to is still
write-locked. If this happens set the request aside in a local list
to continue trying dispatching requests such as READ requests or a
WRITE/ZONE_APPEND requests targetting other zones. This way we can
still keep a high queue depth without starving other requests even if
one request can't be served due to zone write-locking.
Finally, make sure that the bio sector position indicates the actual
write position as indicated by the device on completion.
Signed-off-by: Keith Busch <kbusch@kernel.org>
[ jth: added zone-append specific add_page and merge_page helpers ]
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Block drivers must call del_gendisk() before blk_cleanup_queue().
del_gendisk() calls kobject_del() and kobject_del() waits until any
ongoing sysfs callback functions have finished. In other words, the
sysfs callback functions won't be called for a queue in the dying
state. Hence remove the "dying" checks from the sysfs callback
functions.
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We have updated limits after calling wbt_set_min_lat(). No need to
update again.
Reviewed-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
cecf5d87ff ("block: split .sysfs_lock into two locks") starts to
release & acquire sysfs_lock before registering/un-registering elevator
queue during switching elevator for avoiding potential deadlock from
showing & storing 'queue/iosched' attributes and removing elevator's
kobject.
Turns out there isn't such deadlock because 'q->sysfs_lock' isn't
required in .show & .store of queue/iosched's attributes, and just
elevator's sysfs lock is acquired in elv_iosched_store() and
elv_iosched_show(). So it is safe to hold queue's sysfs lock when
registering/un-registering elevator queue.
The biggest issue is that commit cecf5d87ff assumes that concurrent
write on 'queue/scheduler' can't happen. However, this assumption isn't
true, because kernfs_fop_write() only guarantees that concurrent write
aren't called on the same open file, but the write could be from
different open on the file. So we can't release & re-acquire queue's
sysfs lock during switching elevator, otherwise use-after-free on
elevator could be triggered.
Fixes the issue by not releasing queue's sysfs lock during switching
elevator.
Fixes: cecf5d87ff ("block: split .sysfs_lock into two locks")
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=Qt+h
-----END PGP SIGNATURE-----
Merge tag 'for-5.4/block-2019-09-16' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- Two NVMe pull requests:
- ana log parse fix from Anton
- nvme quirks support for Apple devices from Ben
- fix missing bio completion tracing for multipath stack devices
from Hannes and Mikhail
- IP TOS settings for nvme rdma and tcp transports from Israel
- rq_dma_dir cleanups from Israel
- tracing for Get LBA Status command from Minwoo
- Some nvme-tcp cleanups from Minwoo, Potnuri and Myself
- Some consolidation between the fabrics transports for handling
the CAP register
- reset race with ns scanning fix for fabrics (move fabrics
commands to a dedicated request queue with a different lifetime
from the admin request queue)."
- controller reset and namespace scan races fixes
- nvme discovery log change uevent support
- naming improvements from Keith
- multiple discovery controllers reject fix from James
- some regular cleanups from various people
- Series fixing (and re-fixing) null_blk debug printing and nr_devices
checks (André)
- A few pull requests from Song, with fixes from Andy, Guoqing,
Guilherme, Neil, Nigel, and Yufen.
- REQ_OP_ZONE_RESET_ALL support (Chaitanya)
- Bio merge handling unification (Christoph)
- Pick default elevator correctly for devices with special needs
(Damien)
- Block stats fixes (Hou)
- Timeout and support devices nbd fixes (Mike)
- Series fixing races around elevator switching and device add/remove
(Ming)
- sed-opal cleanups (Revanth)
- Per device weight support for BFQ (Fam)
- Support for blk-iocost, a new model that can properly account cost of
IO workloads. (Tejun)
- blk-cgroup writeback fixes (Tejun)
- paride queue init fixes (zhengbin)
- blk_set_runtime_active() cleanup (Stanley)
- Block segment mapping optimizations (Bart)
- lightnvm fixes (Hans/Minwoo/YueHaibing)
- Various little fixes and cleanups
* tag 'for-5.4/block-2019-09-16' of git://git.kernel.dk/linux-block: (186 commits)
null_blk: format pr_* logs with pr_fmt
null_blk: match the type of parameter nr_devices
null_blk: do not fail the module load with zero devices
block: also check RQF_STATS in blk_mq_need_time_stamp()
block: make rq sector size accessible for block stats
bfq: Fix bfq linkage error
raid5: use bio_end_sector in r5_next_bio
raid5: remove STRIPE_OPS_REQ_PENDING
md: add feature flag MD_FEATURE_RAID0_LAYOUT
md/raid0: avoid RAID0 data corruption due to layout confusion.
raid5: don't set STRIPE_HANDLE to stripe which is in batch list
raid5: don't increment read_errors on EILSEQ return
nvmet: fix a wrong error status returned in error log page
nvme: send discovery log page change events to userspace
nvme: add uevent variables for controller devices
nvme: enable aen regardless of the presence of I/O queues
nvme-fabrics: allow discovery subsystems accept a kato
nvmet: Use PTR_ERR_OR_ZERO() in nvmet_init_discovery()
nvme: Remove redundant assignment of cq vector
nvme: Assign subsys instance from first ctrl
...
cecf5d87ff ("block: split .sysfs_lock into two locks") starts to
release & actuire sysfs_lock again during switching elevator. So it
isn't enough to prevent switching elevator from happening by simply
clearing QUEUE_FLAG_REGISTERED with holding sysfs_lock, because
in-progress switch still can move on after re-acquiring the lock,
meantime the flag of QUEUE_FLAG_REGISTERED won't get checked.
Fixes this issue by checking 'q->elevator' directly & locklessly after
q->kobj is removed in blk_unregister_queue(), this way is safe because
q->elevator can't be changed at that time.
Fixes: cecf5d87ff ("block: split .sysfs_lock into two locks")
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The kernfs built-in lock of 'kn->count' is held in sysfs .show/.store
path. Meantime, inside block's .show/.store callback, q->sysfs_lock is
required.
However, when mq & iosched kobjects are removed via
blk_mq_unregister_dev() & elv_unregister_queue(), q->sysfs_lock is held
too. This way causes AB-BA lock because the kernfs built-in lock of
'kn-count' is required inside kobject_del() too, see the lockdep warning[1].
On the other hand, it isn't necessary to acquire q->sysfs_lock for
both blk_mq_unregister_dev() & elv_unregister_queue() because
clearing REGISTERED flag prevents storing to 'queue/scheduler'
from being happened. Also sysfs write(store) is exclusive, so no
necessary to hold the lock for elv_unregister_queue() when it is
called in switching elevator path.
So split .sysfs_lock into two: one is still named as .sysfs_lock for
covering sync .store, the other one is named as .sysfs_dir_lock
for covering kobjects and related status change.
sysfs itself can handle the race between add/remove kobjects and
showing/storing attributes under kobjects. For switching scheduler
via storing to 'queue/scheduler', we use the queue flag of
QUEUE_FLAG_REGISTERED with .sysfs_lock for avoiding the race, then
we can avoid to hold .sysfs_lock during removing/adding kobjects.
[1] lockdep warning
======================================================
WARNING: possible circular locking dependency detected
5.3.0-rc3-00044-g73277fc75ea0 #1380 Not tainted
------------------------------------------------------
rmmod/777 is trying to acquire lock:
00000000ac50e981 (kn->count#202){++++}, at: kernfs_remove_by_name_ns+0x59/0x72
but task is already holding lock:
00000000fb16ae21 (&q->sysfs_lock){+.+.}, at: blk_unregister_queue+0x78/0x10b
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&q->sysfs_lock){+.+.}:
__lock_acquire+0x95f/0xa2f
lock_acquire+0x1b4/0x1e8
__mutex_lock+0x14a/0xa9b
blk_mq_hw_sysfs_show+0x63/0xb6
sysfs_kf_seq_show+0x11f/0x196
seq_read+0x2cd/0x5f2
vfs_read+0xc7/0x18c
ksys_read+0xc4/0x13e
do_syscall_64+0xa7/0x295
entry_SYSCALL_64_after_hwframe+0x49/0xbe
-> #0 (kn->count#202){++++}:
check_prev_add+0x5d2/0xc45
validate_chain+0xed3/0xf94
__lock_acquire+0x95f/0xa2f
lock_acquire+0x1b4/0x1e8
__kernfs_remove+0x237/0x40b
kernfs_remove_by_name_ns+0x59/0x72
remove_files+0x61/0x96
sysfs_remove_group+0x81/0xa4
sysfs_remove_groups+0x3b/0x44
kobject_del+0x44/0x94
blk_mq_unregister_dev+0x83/0xdd
blk_unregister_queue+0xa0/0x10b
del_gendisk+0x259/0x3fa
null_del_dev+0x8b/0x1c3 [null_blk]
null_exit+0x5c/0x95 [null_blk]
__se_sys_delete_module+0x204/0x337
do_syscall_64+0xa7/0x295
entry_SYSCALL_64_after_hwframe+0x49/0xbe
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&q->sysfs_lock);
lock(kn->count#202);
lock(&q->sysfs_lock);
lock(kn->count#202);
*** DEADLOCK ***
2 locks held by rmmod/777:
#0: 00000000e69bd9de (&lock){+.+.}, at: null_exit+0x2e/0x95 [null_blk]
#1: 00000000fb16ae21 (&q->sysfs_lock){+.+.}, at: blk_unregister_queue+0x78/0x10b
stack backtrace:
CPU: 0 PID: 777 Comm: rmmod Not tainted 5.3.0-rc3-00044-g73277fc75ea0 #1380
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS ?-20180724_192412-buildhw-07.phx4
Call Trace:
dump_stack+0x9a/0xe6
check_noncircular+0x207/0x251
? print_circular_bug+0x32a/0x32a
? find_usage_backwards+0x84/0xb0
check_prev_add+0x5d2/0xc45
validate_chain+0xed3/0xf94
? check_prev_add+0xc45/0xc45
? mark_lock+0x11b/0x804
? check_usage_forwards+0x1ca/0x1ca
__lock_acquire+0x95f/0xa2f
lock_acquire+0x1b4/0x1e8
? kernfs_remove_by_name_ns+0x59/0x72
__kernfs_remove+0x237/0x40b
? kernfs_remove_by_name_ns+0x59/0x72
? kernfs_next_descendant_post+0x7d/0x7d
? strlen+0x10/0x23
? strcmp+0x22/0x44
kernfs_remove_by_name_ns+0x59/0x72
remove_files+0x61/0x96
sysfs_remove_group+0x81/0xa4
sysfs_remove_groups+0x3b/0x44
kobject_del+0x44/0x94
blk_mq_unregister_dev+0x83/0xdd
blk_unregister_queue+0xa0/0x10b
del_gendisk+0x259/0x3fa
? disk_events_poll_msecs_store+0x12b/0x12b
? check_flags+0x1ea/0x204
? mark_held_locks+0x1f/0x7a
null_del_dev+0x8b/0x1c3 [null_blk]
null_exit+0x5c/0x95 [null_blk]
__se_sys_delete_module+0x204/0x337
? free_module+0x39f/0x39f
? blkcg_maybe_throttle_current+0x8a/0x718
? rwlock_bug+0x62/0x62
? __blkcg_punt_bio_submit+0xd0/0xd0
? trace_hardirqs_on_thunk+0x1a/0x20
? mark_held_locks+0x1f/0x7a
? do_syscall_64+0x4c/0x295
do_syscall_64+0xa7/0x295
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7fb696cdbe6b
Code: 73 01 c3 48 8b 0d 1d 20 0c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 008
RSP: 002b:00007ffec9588788 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
RAX: ffffffffffffffda RBX: 0000559e589137c0 RCX: 00007fb696cdbe6b
RDX: 000000000000000a RSI: 0000000000000800 RDI: 0000559e58913828
RBP: 0000000000000000 R08: 00007ffec9587701 R09: 0000000000000000
R10: 00007fb696d4eae0 R11: 0000000000000206 R12: 00007ffec95889b0
R13: 00007ffec95896b3 R14: 0000559e58913260 R15: 0000559e589137c0
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There are 4 users which check if queue is registered, so add one helper
to check it.
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_exit_queue will free elevator_data, while blk_mq_requeue_work
will access it. Move cancel of requeue_work to the front of
blk_exit_queue to avoid use-after-free.
blk_exit_queue blk_mq_requeue_work
__elevator_exit blk_mq_run_hw_queues
blk_mq_exit_sched blk_mq_run_hw_queue
dd_exit_queue blk_mq_hctx_has_pending
kfree(elevator_data) blk_mq_sched_has_work
dd_has_work
Fixes: fbc2a15e34 ("blk-mq: move cancel of requeue_work into blk_mq_release")
Cc: stable@vger.kernel.org
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In theory, IO scheduler belongs to request queue, and the request pool
of sched tags belongs to the request queue too.
However, the current tags allocation interfaces are re-used for both
driver tags and sched tags, and driver tags is definitely host wide,
and doesn't belong to any request queue, same with its request pool.
So we need tagset instance for freeing request of sched tags.
Meantime, blk_mq_free_tag_set() often follows blk_cleanup_queue() in case
of non-BLK_MQ_F_TAG_SHARED, this way requires that request pool of sched
tags to be freed before calling blk_mq_free_tag_set().
Commit 47cdee29ef ("block: move blk_exit_queue into __blk_release_queue")
moves blk_exit_queue into __blk_release_queue for simplying the fast
path in generic_make_request(), then causes oops during freeing requests
of sched tags in __blk_release_queue().
Fix the above issue by move freeing request pool of sched tags into
blk_cleanup_queue(), this way is safe becasue queue has been frozen and no any
in-queue requests at that time. Freeing sched tags has to be kept in queue's
release handler becasue there might be un-completed dispatch activity
which might refer to sched tags.
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@lst.de>
Fixes: 47cdee29ef ("block: move blk_exit_queue into __blk_release_queue")
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 498f6650ae ("block: Fix a race between the cgroup code and
request queue initialization") moves what blk_exit_queue does into
blk_cleanup_queue() for fixing issue caused by changing back
queue lock.
However, after legacy request IO path is killed, driver queue lock
won't be used at all, and there isn't story for changing back
queue lock. Then the issue addressed by Commit 498f6650ae doesn't
exist any more.
So move move blk_exit_queue into __blk_release_queue.
This patch basically reverts the following two commits:
498f6650ae block: Fix a race between the cgroup code and request queue initialization
24ecc35853 block: Ensure that a request queue is dissociated from the cgroup controller
Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If the low level driver has no timeout handler, the
/sys/block/<disk>/queue/io_timeout will not be displayed.
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Weiping Zhang <zhangweiping@didiglobal.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For q->poll_nsec == -1, means doing classic poll, not hybrid poll.
We introduce a new flag BLK_MQ_POLL_CLASSIC to replace -1, which
may make code much easier to read.
Additionally, since val is an int obtained with kstrtoint(), val can be
a negative value other than -1, so return -EINVAL for that case.
Thanks to Damien Le Moal for some good suggestion.
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There's no reason to set wbt min lat and freeze request queue
if current value is the same.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Aleksei Zakharov <zakharov.a.g@yandex.ru>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The Notes section of the comment was removed, because now
blk_release_queue can only be executed from blk_cleanup_queue (being
called when the q->kobj reaches zero), and also blk_init_queue was removed
in a1ce35fa49.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas. Additionally, we have
a pile of annotation, unused variable and minor updates. The big API
change is the updates for Christoph's DMA rework which include
removing the DISABLE_CLUSTERING flag. And finally there are a couple
of target tree updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXCEUNiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdjKAP9vrTTv
qFaYmAoRSbPq9ZiixaXLMy0K/6o76Uay0gnBqgD/fgn3jg/KQ6alNaCjmfeV3wAj
u1j3H7tha9j1it+4pUw=
=GDa+
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas.
Additionally, we have a pile of annotation, unused variable and minor
updates.
The big API change is the updates for Christoph's DMA rework which
include removing the DISABLE_CLUSTERING flag.
And finally there are a couple of target tree updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (259 commits)
scsi: isci: request: mark expected switch fall-through
scsi: isci: remote_node_context: mark expected switch fall-throughs
scsi: isci: remote_device: Mark expected switch fall-throughs
scsi: isci: phy: Mark expected switch fall-through
scsi: iscsi: Capture iscsi debug messages using tracepoints
scsi: myrb: Mark expected switch fall-throughs
scsi: megaraid: fix out-of-bound array accesses
scsi: mpt3sas: mpt3sas_scsih: Mark expected switch fall-through
scsi: fcoe: remove set but not used variable 'port'
scsi: smartpqi: call pqi_free_interrupts() in pqi_shutdown()
scsi: smartpqi: fix build warnings
scsi: smartpqi: update driver version
scsi: smartpqi: add ofa support
scsi: smartpqi: increase fw status register read timeout
scsi: smartpqi: bump driver version
scsi: smartpqi: add smp_utils support
scsi: smartpqi: correct lun reset issues
scsi: smartpqi: correct volume status
scsi: smartpqi: do not offline disks for transient did no connect conditions
scsi: smartpqi: allow for larger raid maps
...
