There are a few MSRs and control register bits that the kernel
normally needs to modify during boot. But, TDX disallows
modification of these registers to help provide consistent security
guarantees. Fortunately, TDX ensures that these are all in the correct
state before the kernel loads, which means the kernel does not need to
modify them.
The conditions to avoid are:
* Any writes to the EFER MSR
* Clearing CR4.MCE
This theoretically makes the guest boot more fragile. If, for instance,
EFER was set up incorrectly and a WRMSR was performed, it will trigger
early exception panic or a triple fault, if it's before early
exceptions are set up. However, this is likely to trip up the guest
BIOS long before control reaches the kernel. In any case, these kinds
of problems are unlikely to occur in production environments, and
developers have good debug tools to fix them quickly.
Change the common boot code to work on TDX and non-TDX systems.
This should have no functional effect on non-TDX systems.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-24-kirill.shutemov@linux.intel.com
Due to
103a4908ad ("x86/head/64: Disable stack protection for head$(BITS).o")
kernel/head{32,64}.c are compiled with -fno-stack-protector to allow
a call to set_bringup_idt_handler(), which would otherwise have stack
protection enabled with CONFIG_STACKPROTECTOR_STRONG.
While sufficient for that case, there may still be issues with calls to
any external functions that were compiled with stack protection enabled
that in-turn make stack-protected calls, or if the exception handlers
set up by set_bringup_idt_handler() make calls to stack-protected
functions.
Subsequent patches for SEV-SNP CPUID validation support will introduce
both such cases. Attempting to disable stack protection for everything
in scope to address that is prohibitive since much of the code, like the
SEV-ES #VC handler, is shared code that remains in use after boot and
could benefit from having stack protection enabled. Attempting to inline
calls is brittle and can quickly balloon out to library/helper code
where that's not really an option.
Instead, re-enable stack protection for head32.c/head64.c, and make the
appropriate changes to ensure the segment used for the stack canary is
initialized in advance of any stack-protected C calls.
For head64.c:
- The BSP will enter from startup_64() and call into C code
(startup_64_setup_env()) shortly after setting up the stack, which
may result in calls to stack-protected code. Set up %gs early to allow
for this safely.
- APs will enter from secondary_startup_64*(), and %gs will be set up
soon after. There is one call to C code prior to %gs being setup
(__startup_secondary_64()), but it is only to fetch 'sme_me_mask'
global, so just load 'sme_me_mask' directly instead, and remove the
now-unused __startup_secondary_64() function.
For head32.c:
- BSPs/APs will set %fs to __BOOT_DS prior to any C calls. In recent
kernels, the compiler is configured to access the stack canary at
%fs:__stack_chk_guard [1], which overlaps with the initial per-cpu
'__stack_chk_guard' variable in the initial/"master" .data..percpu
area. This is sufficient to allow access to the canary for use
during initial startup, so no changes are needed there.
[1] 3fb0fdb3bb ("x86/stackprotector/32: Make the canary into a regular percpu variable")
[ bp: Massage commit message. ]
Suggested-by: Joerg Roedel <jroedel@suse.de> #for 64-bit %gs set up
Signed-off-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220307213356.2797205-24-brijesh.singh@amd.com
sme_enable() handles feature detection for both SEV and SME. Future
patches will also use it for SEV-SNP feature detection/setup, which
will need to be done immediately after the first #VC handler is set up.
Move it now in preparation.
Signed-off-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Venu Busireddy <venu.busireddy@oracle.com>
Link: https://lore.kernel.org/r/20220307213356.2797205-9-brijesh.singh@amd.com
Annotate away some of the generic code references. This is things
where we take the address of a symbol for exception handling or return
addresses (eg. context switch).
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/20220308154318.877758523@infradead.org
Kernel entry points should be having ENDBR on for IBT configs.
The SYSCALL entry points are found through taking their respective
address in order to program them in the MSRs, while the exception
entry points are found through UNWIND_HINT_IRET_REGS.
The rule is that any UNWIND_HINT_IRET_REGS at sym+0 should have an
ENDBR, see the later objtool ibt validation patch.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/20220308154317.933157479@infradead.org
Even though Xen currently doesn't advertise IBT, prepare for when it
will eventually do so and sprinkle the ENDBR dust accordingly.
Even though most of the entry points are IRET like, the CPL0
Hypervisor can set WAIT-FOR-ENDBR and demand ENDBR at these sites.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/20220308154317.873919996@infradead.org
By doing an early rewrite of 'jmp native_iret` in
restore_regs_and_return_to_kernel() we can get rid of the last
INTERRUPT_RETURN user and paravirt_iret.
Suggested-by: Andrew Cooper <Andrew.Cooper3@citrix.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/20220308154317.815039833@infradead.org
The AP bringup code uses the trampoline_pgd page-table which
establishes global mappings in the user range of the address space.
Flush the global TLB entries after the indentity mappings are removed so
no stale entries remain in the TLB.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20211202153226.22946-3-joro@8bytes.org
The register offsets in <asm/ptrace-abi.h> are duplicated in
entry/calling.h, but are formatted differently and therefore not
compatible. Use the version from <asm/ptrace-abi.h> consistently.
Signed-off-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20210510185316.3307264-2-hpa@zytor.com
(Arvind Sankar)
- Remove -m16 workaround now that the GCC versions that need it are unsupported
(Nick Desaulniers)
-----BEGIN PGP SIGNATURE-----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=Qk/S
-----END PGP SIGNATURE-----
Merge tag 'x86_build_for_v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 build updates from Borislav Petkov:
"Two x86 build fixes:
- Fix the vmlinux size check on 64-bit along with adding useful
clarifications on the topic (Arvind Sankar)
- Remove -m16 workaround now that the GCC versions that need it are
unsupported (Nick Desaulniers)"
* tag 'x86_build_for_v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/build: Remove -m16 workaround for unsupported versions of GCC
x86/build: Fix vmlinux size check on 64-bit
(Gabriel Krisman Bertazi)
- All kinds of minor cleanups all over the tree.
-----BEGIN PGP SIGNATURE-----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=lLiH
-----END PGP SIGNATURE-----
Merge tag 'x86_cleanups_for_v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cleanups from Borislav Petkov:
"Another branch with a nicely negative diffstat, just the way I
like 'em:
- Remove all uses of TIF_IA32 and TIF_X32 and reclaim the two bits in
the end (Gabriel Krisman Bertazi)
- All kinds of minor cleanups all over the tree"
* tag 'x86_cleanups_for_v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86/ia32_signal: Propagate __user annotation properly
x86/alternative: Update text_poke_bp() kernel-doc comment
x86/PCI: Make a kernel-doc comment a normal one
x86/asm: Drop unused RDPID macro
x86/boot/compressed/64: Use TEST %reg,%reg instead of CMP $0,%reg
x86/head64: Remove duplicate include
x86/mm: Declare 'start' variable where it is used
x86/head/64: Remove unused GET_CR2_INTO() macro
x86/boot: Remove unused finalize_identity_maps()
x86/uaccess: Document copy_from_user_nmi()
x86/dumpstack: Make show_trace_log_lvl() static
x86/mtrr: Fix a kernel-doc markup
x86/setup: Remove unused MCA variables
x86, libnvdimm/test: Remove COPY_MC_TEST
x86: Reclaim TIF_IA32 and TIF_X32
x86/mm: Convert mmu context ia32_compat into a proper flags field
x86/elf: Use e_machine to check for x32/ia32 in setup_additional_pages()
elf: Expose ELF header on arch_setup_additional_pages()
x86/elf: Use e_machine to select start_thread for x32
elf: Expose ELF header in compat_start_thread()
...
Commit
4b47cdbda6 ("x86/head/64: Move early exception dispatch to C code")
removed the usage of GET_CR2_INTO().
Drop the definition as well, and related definitions in paravirt.h and
asm-offsets.h
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20201005151208.2212886-3-nivedita@alum.mit.edu
Commit
b4e0409a36 ("x86: check vmlinux limits, 64-bit")
added a check that the size of the 64-bit kernel is less than
KERNEL_IMAGE_SIZE.
The check uses (_end - _text), but this is not enough. The initial
PMD used in startup_64() (level2_kernel_pgt) can only map upto
KERNEL_IMAGE_SIZE from __START_KERNEL_map, not from _text, and the
modules area (MODULES_VADDR) starts at KERNEL_IMAGE_SIZE.
The correct check is what is currently done for 32-bit, since
LOAD_OFFSET is defined appropriately for the two architectures. Just
check (_end - LOAD_OFFSET) against KERNEL_IMAGE_SIZE unconditionally.
Note that on 32-bit, the limit is not strict: KERNEL_IMAGE_SIZE is not
really used by the main kernel. The higher the kernel is located, the
less the space available for the vmalloc area. However, it is used by
KASLR in the compressed stub to limit the maximum address of the kernel
to a safe value.
Clean up various comments to clarify that despite the name,
KERNEL_IMAGE_SIZE is not a limit on the size of the kernel image, but a
limit on the maximum virtual address that the image can occupy.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20201029161903.2553528-1-nivedita@alum.mit.edu
When SEV is enabled, the kernel requests the C-bit position again from
the hypervisor to build its own page-table. Since the hypervisor is an
untrusted source, the C-bit position needs to be verified before the
kernel page-table is used.
Call sev_verify_cbit() before writing the CR3.
[ bp: Massage. ]
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lkml.kernel.org/r/20201028164659.27002-5-joro@8bytes.org
The APs are not ready to handle exceptions when verify_cpu() is called
in secondary_startup_64().
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lkml.kernel.org/r/20200907131613.12703-69-joro@8bytes.org
Add the infrastructure to handle #VC exceptions when the kernel runs on
virtual addresses and has mapped a GHCB. This handler will be used until
the runtime #VC handler takes over.
Since the handler runs very early, disable instrumentation for sev-es.c.
[ bp: Make vc_ghcb_invalidate() __always_inline so that it can be
inlined in noinstr functions like __sev_es_nmi_complete(). ]
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200908123816.GB3764@8bytes.org
Setup an early handler for #VC exceptions. There is no GHCB mapped
yet, so just re-use the vc_no_ghcb_handler(). It can only handle
CPUID exit-codes, but that should be enough to get the kernel through
verify_cpu() and __startup_64() until it runs on virtual addresses.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
[ boot failure Error: kernel_ident_mapping_init() failed. ]
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lkml.kernel.org/r/20200908123517.GA3764@8bytes.org
Move the assembly coded dispatch between page-faults and all other
exceptions to C code to make it easier to maintain and extend.
Also change the return-type of early_make_pgtable() to bool and make it
static.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200907131613.12703-36-joro@8bytes.org
Add a separate bringup IDT for the CPU bringup code that will be used
until the kernel switches to the idt_table. There are two reasons for a
separate IDT:
1) When the idt_table is set up and the secondary CPUs are
booted, it contains entries (e.g. IST entries) which
require certain CPU state to be set up. This includes a
working TSS (for IST), MSR_GS_BASE (for stack protector) or
CR4.FSGSBASE (for paranoid_entry) path. By using a
dedicated IDT for early boot this state need not to be set
up early.
2) The idt_table is static to idt.c, so any function
using/modifying must be in idt.c too. That means that all
compiler driven instrumentation like tracing or KASAN is
also active in this code. But during early CPU bringup the
environment is not set up for this instrumentation to work
correctly.
To avoid all of these hassles and make early exception handling robust,
use a dedicated bringup IDT.
The IDT is loaded two times, first on the boot CPU while the kernel is
still running on direct mapped addresses, and again later after the
switch to kernel addresses has happened. The second IDT load happens on
the boot and secondary CPUs.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200907131613.12703-34-joro@8bytes.org
Make sure there is a stack once the kernel runs from virtual addresses.
At this stage any secondary CPU which boots will have lost its stack
because the kernel switched to a new page-table which does not map the
real-mode stack anymore.
This is needed for handling early #VC exceptions caused by instructions
like CPUID.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lkml.kernel.org/r/20200907131613.12703-33-joro@8bytes.org
Make sure segments are properly set up before setting up an IDT and
doing anything that might cause a #VC exception. This is later needed
for early exception handling.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lkml.kernel.org/r/20200907131613.12703-32-joro@8bytes.org
Load the GDT right after switching to virtual addresses to make sure
there is a defined GDT for exception handling.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lkml.kernel.org/r/20200907131613.12703-31-joro@8bytes.org
Handling exceptions during boot requires a working GDT. The kernel GDT
can't be used on the direct mapping, so load a startup GDT and setup
segments.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200907131613.12703-30-joro@8bytes.org
Remove all the code which was there to emit the system vector stubs. All
users are gone.
Move the now unused GET_CR2_INTO macro muck to head_64.S where the last
user is. Fixup the eye hurting comment there while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Andy Lutomirski <luto@kernel.org>
Link: https://lore.kernel.org/r/20200521202119.927433002@linutronix.de
The replacement of <asm/pgrable.h> with <linux/pgtable.h> made the include
of the latter in the middle of asm includes. Fix this up with the aid of
the below script and manual adjustments here and there.
import sys
import re
if len(sys.argv) is not 3:
print "USAGE: %s <file> <header>" % (sys.argv[0])
sys.exit(1)
hdr_to_move="#include <linux/%s>" % sys.argv[2]
moved = False
in_hdrs = False
with open(sys.argv[1], "r") as f:
lines = f.readlines()
for _line in lines:
line = _line.rstrip('
')
if line == hdr_to_move:
continue
if line.startswith("#include <linux/"):
in_hdrs = True
elif not moved and in_hdrs:
moved = True
print hdr_to_move
print line
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-4-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The include/linux/pgtable.h is going to be the home of generic page table
manipulation functions.
Start with moving asm-generic/pgtable.h to include/linux/pgtable.h and
make the latter include asm/pgtable.h.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-3-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change all assembly code which is marked using END (and not ENDPROC).
Switch all these to the appropriate new annotation SYM_CODE_START and
SYM_CODE_END.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> [xen bits]
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Cao jin <caoj.fnst@cn.fujitsu.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: linux-arch@vger.kernel.org
Cc: Maran Wilson <maran.wilson@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: "Steven Rostedt (VMware)" <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Cc: xen-devel@lists.xenproject.org
Link: https://lkml.kernel.org/r/20191011115108.12392-24-jslaby@suse.cz
GLOBAL is an x86's custom macro and is going to die very soon. It was
meant for global symbols, but here, it was used for functions. Instead,
use the new macros SYM_FUNC_START* and SYM_CODE_START* (depending on the
type of the function) which are dedicated to global functions. And since
they both require a closing by SYM_*_END, do that here too.
startup_64, which does not use GLOBAL but uses .globl explicitly, is
converted too.
"No alignments" are preserved.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Allison Randal <allison@lohutok.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Cao jin <caoj.fnst@cn.fujitsu.com>
Cc: Enrico Weigelt <info@metux.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-arch@vger.kernel.org
Cc: Maran Wilson <maran.wilson@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20191011115108.12392-17-jslaby@suse.cz
Use the new SYM_DATA, SYM_DATA_START, and SYM_DATA_END in both 32 and 64
bit head_*.S. In the 64-bit version, define also
SYM_DATA_START_PAGE_ALIGNED locally using the new SYM_START. It is used
in the code instead of NEXT_PAGE() which was defined in this file and
had been using the obsolete macro GLOBAL().
Now, the data in the 64-bit object file look sane:
Value Size Type Bind Vis Ndx Name
0000 4096 OBJECT GLOBAL DEFAULT 15 init_level4_pgt
1000 4096 OBJECT GLOBAL DEFAULT 15 level3_kernel_pgt
2000 2048 OBJECT GLOBAL DEFAULT 15 level2_kernel_pgt
3000 4096 OBJECT GLOBAL DEFAULT 15 level2_fixmap_pgt
4000 4096 OBJECT GLOBAL DEFAULT 15 level1_fixmap_pgt
5000 2 OBJECT GLOBAL DEFAULT 15 early_gdt_descr
5002 8 OBJECT LOCAL DEFAULT 15 early_gdt_descr_base
500a 8 OBJECT GLOBAL DEFAULT 15 phys_base
0000 8 OBJECT GLOBAL DEFAULT 17 initial_code
0008 8 OBJECT GLOBAL DEFAULT 17 initial_gs
0010 8 OBJECT GLOBAL DEFAULT 17 initial_stack
0000 4 OBJECT GLOBAL DEFAULT 19 early_recursion_flag
1000 4096 OBJECT GLOBAL DEFAULT 19 early_level4_pgt
2000 0x40000 OBJECT GLOBAL DEFAULT 19 early_dynamic_pgts
0000 4096 OBJECT GLOBAL DEFAULT 22 empty_zero_page
All have correct size and type now.
Note that this also removes implicit 16B alignment previously inserted
by ENTRY:
* initial_code, setup_once_ref, initial_page_table, initial_stack,
boot_gdt are still aligned
* early_gdt_descr is now properly aligned as was intended before ENTRY
was added there long time ago
* phys_base's alignment is kept by an explicitly added new alignment
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Cao jin <caoj.fnst@cn.fujitsu.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: linux-arch@vger.kernel.org
Cc: Maran Wilson <maran.wilson@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20191011115108.12392-12-jslaby@suse.cz
Use the newly added SYM_CODE_START_LOCAL* to annotate beginnings of
all pseudo-functions (those ending with END until now) which do not
have ".globl" annotation. This is needed to balance END for tools that
generate debuginfo. Note that ENDs are switched to SYM_CODE_END too so
that everybody can see the pairing.
C-like functions (which handle frame ptr etc.) are not annotated here,
hence SYM_CODE_* macros are used here, not SYM_FUNC_*. Note that the
32bit version of early_idt_handler_common already had ENDPROC -- switch
that to SYM_CODE_END for the same reason as above (and to be the same as
64bit).
While early_idt_handler_common is LOCAL, it's name is not prepended with
".L" as it happens to appear in call traces.
bad_get_user*, and bad_put_user are now aligned, as they are separate
functions. They do not mind to be aligned -- no need to be compact
there.
early_idt_handler_common is aligned now too, as it is after
early_idt_handler_array, so as well no need to be compact there.
verify_cpu is self-standing and included in other .S files, so align it
too.
The others have alignment preserved to what it used to be (using the
_NOALIGN variant of macros).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Alexios Zavras <alexios.zavras@intel.com>
Cc: Allison Randal <allison@lohutok.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Cao jin <caoj.fnst@cn.fujitsu.com>
Cc: Enrico Weigelt <info@metux.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: linux-arch@vger.kernel.org
Cc: Maran Wilson <maran.wilson@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20191011115108.12392-6-jslaby@suse.cz
Moving early_recursion_flag (4 bytes) after early_level4_pgt (4k) and
early_dynamic_pgts (256k) saves 4k which are used for alignment of
early_level4_pgt after early_recursion_flag.
The real improvement is merely on the source code side. Previously it
was:
* __INITDATA + .balign
* early_recursion_flag variable
* a ton of CPP MACROS
* __INITDATA (again)
* early_top_pgt and early_recursion_flag variables
* .data
Now, it is a bit simpler:
* a ton of CPP MACROS
* __INITDATA + .balign
* early_top_pgt and early_recursion_flag variables
* early_recursion_flag variable
* .data
On the binary level the change looks like this:
Before:
(sections)
12 .init.data 00042000 0000000000000000 0000000000000000 00008000 2**12
(symbols)
000000 4 OBJECT GLOBAL DEFAULT 22 early_recursion_flag
001000 4096 OBJECT GLOBAL DEFAULT 22 early_top_pgt
002000 0x40000 OBJECT GLOBAL DEFAULT 22 early_dynamic_pgts
After:
(sections)
12 .init.data 00041004 0000000000000000 0000000000000000 00008000 2**12
(symbols)
000000 4096 OBJECT GLOBAL DEFAULT 22 early_top_pgt
001000 0x40000 OBJECT GLOBAL DEFAULT 22 early_dynamic_pgts
041000 4 OBJECT GLOBAL DEFAULT 22 early_recursion_flag
So the resulting vmlinux is smaller by 4k with my toolchain as many
other variables can be placed after early_recursion_flag to fill the
rest of the page. Note that this is only .init data, so it is freed
right after being booted anyway. Savings on-disk are none -- compression
of zeros is easy, so the size of bzImage is the same pre and post the
change.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20191003095238.29831-1-jslaby@suse.cz
Commit e6401c1309 ("x86/irq/64: Split the IRQ stack into its own pages")
missed to update one piece of comment as it did to its peer in Xen, which
will confuse people who still need to read comment.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190719081635.26528-1-caoj.fnst@cn.fujitsu.com
Pull x86 fixes from Thomas Gleixner:
"A set of x86 specific fixes and updates:
- The CR2 corruption fixes which store CR2 early in the entry code
and hand the stored address to the fault handlers.
- Revert a forgotten leftover of the dropped FSGSBASE series.
- Plug a memory leak in the boot code.
- Make the Hyper-V assist functionality robust by zeroing the shadow
page.
- Remove a useless check for dead processes with LDT
- Update paravirt and VMware maintainers entries.
- A few cleanup patches addressing various compiler warnings"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/entry/64: Prevent clobbering of saved CR2 value
x86/hyper-v: Zero out the VP ASSIST PAGE on allocation
x86, boot: Remove multiple copy of static function sanitize_boot_params()
x86/boot/compressed/64: Remove unused variable
x86/boot/efi: Remove unused variables
x86/mm, tracing: Fix CR2 corruption
x86/entry/64: Update comments and sanity tests for create_gap
x86/entry/64: Simplify idtentry a little
x86/entry/32: Simplify common_exception
x86/paravirt: Make read_cr2() CALLEE_SAVE
MAINTAINERS: Update PARAVIRT_OPS_INTERFACE and VMWARE_HYPERVISOR_INTERFACE
x86/process: Delete useless check for dead process with LDT
x86: math-emu: Hide clang warnings for 16-bit overflow
x86/e820: Use proper booleans instead of 0/1
x86/apic: Silence -Wtype-limits compiler warnings
x86/mm: Free sme_early_buffer after init
x86/boot: Fix memory leak in default_get_smp_config()
Revert "x86/ptrace: Prevent ptrace from clearing the FS/GS selector" and fix the test
After an objtool improvement, it complains about the fact that
start_cpu0() jumps to code which has an LRET instruction.
arch/x86/kernel/head_64.o: warning: objtool: .head.text+0xe4: unsupported instruction in callable function
Technically, start_cpu0() is callable, but it acts nothing like a
callable function. Prevent objtool from treating it like one by
removing its ELF function annotation.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/6b1b4505fcb90571a55fa1b52d71fb458ca24454.1563413318.git.jpoimboe@redhat.com
Currently, the IRQ stack is hardcoded as the first page of the percpu
area, and the stack canary lives on the IRQ stack. The former gets in
the way of adding an IRQ stack guard page, and the latter is a potential
weakness in the stack canary mechanism.
Split the IRQ stack into its own private percpu pages.
[ tglx: Make 64 and 32 bit share struct irq_stack ]
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: "Chang S. Bae" <chang.seok.bae@intel.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Feng Tang <feng.tang@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Jordan Borgner <mail@jordan-borgner.de>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Maran Wilson <maran.wilson@oracle.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Nicolai Stange <nstange@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Pu Wen <puwen@hygon.cn>
Cc: "Rafael Ávila de Espíndola" <rafael@espindo.la>
Cc: Sean Christopherson <sean.j.christopherson@intel.com>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: x86-ml <x86@kernel.org>
Cc: xen-devel@lists.xenproject.org
Link: https://lkml.kernel.org/r/20190414160146.267376656@linutronix.de
In order to pave the way for hypervisors other than Xen to use the PVH
entry point for VMs, we need to factor the PVH entry code into Xen specific
and hypervisor agnostic components. The first step in doing that, is to
create a new config option for PVH entry that can be enabled
independently from CONFIG_XEN.
Signed-off-by: Maran Wilson <maran.wilson@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Pull x86 paravirt updates from Ingo Molnar:
"Two main changes:
- Remove no longer used parts of the paravirt infrastructure and put
large quantities of paravirt ops under a new config option
PARAVIRT_XXL=y, which is selected by XEN_PV only. (Joergen Gross)
- Enable PV spinlocks on Hyperv (Yi Sun)"
* 'x86-paravirt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/hyperv: Enable PV qspinlock for Hyper-V
x86/hyperv: Add GUEST_IDLE_MSR support
x86/paravirt: Clean up native_patch()
x86/paravirt: Prevent redefinition of SAVE_FLAGS macro
x86/xen: Make xen_reservation_lock static
x86/paravirt: Remove unneeded mmu related paravirt ops bits
x86/paravirt: Move the Xen-only pv_mmu_ops under the PARAVIRT_XXL umbrella
x86/paravirt: Move the pv_irq_ops under the PARAVIRT_XXL umbrella
x86/paravirt: Move the Xen-only pv_cpu_ops under the PARAVIRT_XXL umbrella
x86/paravirt: Move items in pv_info under PARAVIRT_XXL umbrella
x86/paravirt: Introduce new config option PARAVIRT_XXL
x86/paravirt: Remove unused paravirt bits
x86/paravirt: Use a single ops structure
x86/paravirt: Remove clobbers from struct paravirt_patch_site
x86/paravirt: Remove clobbers parameter from paravirt patch functions
x86/paravirt: Make paravirt_patch_call() and paravirt_patch_jmp() static
x86/xen: Add SPDX identifier in arch/x86/xen files
x86/xen: Link platform-pci-unplug.o only if CONFIG_XEN_PVHVM
x86/xen: Move pv specific parts of arch/x86/xen/mmu.c to mmu_pv.c
x86/xen: Move pv irq related functions under CONFIG_XEN_PV umbrella
We met a kernel panic when enabling earlycon, which is due to the fixmap
address of earlycon is not statically setup.
Currently the static fixmap setup in head_64.S only covers 2M virtual
address space, while it actually could be in 4M space with different
kernel configurations, e.g. when VSYSCALL emulation is disabled.
So increase the static space to 4M for now by defining FIXMAP_PMD_NUM to 2,
and add a build time check to ensure that the fixmap is covered by the
initial static page tables.
Fixes: 1ad83c858c ("x86_64,vsyscall: Make vsyscall emulation configurable")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: kernel test robot <rong.a.chen@intel.com>
Reviewed-by: Juergen Gross <jgross@suse.com> (Xen parts)
Cc: H Peter Anvin <hpa@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andy Lutomirsky <luto@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180920025828.23699-1-feng.tang@intel.com
I was mystified as to where the _PAGE_GLOBAL in the kernel page tables
for kernel text came from. I audited all the places I could find, but
I missed one: head_64.S.
The page tables that we create in here live for a long time, and they
also have _PAGE_GLOBAL set, despite whether the processor supports it
or not. It's harmless, and we got *lucky* that the pageattr code
accidentally clears it when we wipe it out of __supported_pte_mask and
then later try to mark kernel text read-only.
Comment some of these properties to make it easier to find and
understand in the future.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kees Cook <keescook@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nadav Amit <namit@vmware.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180406205513.079BB265@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With boot-time switching between paging modes, XEN_PV and XEN_PVH can be
boot into 4-level paging mode.
Tested-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180216114948.68868-2-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The objtool retpoline validation found this indirect jump. Seeing how
it's on CPU bringup before we run userspace it should be safe, annotate
it.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Early boot code should be able to initialize page tables for both 4- and
5-level paging modes.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180214182542.69302-7-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For 4- and 5-level paging we have different 'page_offset_base'.
Let's initialize it at boot-time accordingly to machine capability.
We also have to split __PAGE_OFFSET_BASE into two constants -- for 4-
and 5-level paging.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180214182542.69302-4-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Kernel page table isolation requires to have two PGDs. One for the kernel,
which contains the full kernel mapping plus the user space mapping and one
for user space which contains the user space mappings and the minimal set
of kernel mappings which are required by the architecture to be able to
transition from and to user space.
Add the necessary preliminaries.
[ tglx: Split out from the big kaiser dump. EFI fixup from Kirill ]
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: David Laight <David.Laight@aculab.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Eduardo Valentin <eduval@amazon.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: aliguori@amazon.com
Cc: daniel.gruss@iaik.tugraz.at
Cc: hughd@google.com
Cc: keescook@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pick up some of the MPX commits that modify the syscall entry code,
to have a common base and to reduce conflicts.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Both head_32.S and head_64.S utilize the same value to initialize the
control register CR0. Also, other parts of the kernel might want to access
this initial definition (e.g., emulation code for User-Mode Instruction
Prevention uses this state to provide a sane dummy value for CR0 when
emulating the smsw instruction). Thus, relocate this definition to a
header file from which it can be conveniently accessed.
Suggested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: ricardo.neri@intel.com
Cc: linux-mm@kvack.org
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: linux-arch@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: "Ravi V. Shankar" <ravi.v.shankar@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Chen Yucong <slaoub@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lkml.kernel.org/r/1509135945-13762-3-git-send-email-ricardo.neri-calderon@linux.intel.com
I find the '.ifeq <expression>' directive to be confusing. Reading it
quickly seems to suggest its opposite meaning, or that it's missing an
argument.
Improve readability by replacing all of its x86 uses with
'.if <expression> == 0'.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrei Vagin <avagin@virtuozzo.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/757da028e802c7e98d23fbab8d234b1063e161cf.1508516398.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Looks like we only need pre-built page tables in the CONFIG_XEN_PV=y and
CONFIG_XEN_PVH=y cases.
Let's not provide them for other configurations.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@suse.de>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20170929140821.37654-5-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jiri Slaby reported an ORC issue when unwinding from an idle task. The
stack was:
ffffffff811083c2 do_idle+0x142/0x1e0
ffffffff8110861d cpu_startup_entry+0x5d/0x60
ffffffff82715f58 start_kernel+0x3ff/0x407
ffffffff827153e8 x86_64_start_kernel+0x14e/0x15d
ffffffff810001bf secondary_startup_64+0x9f/0xa0
The ORC unwinder errored out at secondary_startup_64 because the head
code isn't annotated yet so there wasn't a corresponding ORC entry.
Fix that and any other head-related unwinding issues by adding unwind
hints to the head code.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Tested-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/78ef000a2f68f545d6eef44ee912edceaad82ccf.1505764066.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It's no longer possible for this code to be executed, so remove it.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/32a46fe92d2083700599b36872b26e7dfd7b7965.1505764066.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This comment is actively wrong and confusing. It refers to the
registers' stack offsets after the pt_regs has been constructed on the
stack, but this code is *before* that.
At this point the stack just has the standard iret frame, for which no
comment should be needed.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/a3c267b770fc56c9b86df9c11c552848248aace2.1505764066.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Changes to the existing page table macros will allow the SME support to
be enabled in a simple fashion with minimal changes to files that use these
macros. Since the memory encryption mask will now be part of the regular
pagetable macros, we introduce two new macros (_PAGE_TABLE_NOENC and
_KERNPG_TABLE_NOENC) to allow for early pagetable creation/initialization
without the encryption mask before SME becomes active. Two new pgprot()
macros are defined to allow setting or clearing the page encryption mask.
The FIXMAP_PAGE_NOCACHE define is introduced for use with MMIO. SME does
not support encryption for MMIO areas so this define removes the encryption
mask from the page attribute.
Two new macros are introduced (__sme_pa() / __sme_pa_nodebug()) to allow
creating a physical address with the encryption mask. These are used when
working with the cr3 register so that the PGD can be encrypted. The current
__va() macro is updated so that the virtual address is generated based off
of the physical address without the encryption mask thus allowing the same
virtual address to be generated regardless of whether encryption is enabled
for that physical location or not.
Also, an early initialization function is added for SME. If SME is active,
this function:
- Updates the early_pmd_flags so that early page faults create mappings
with the encryption mask.
- Updates the __supported_pte_mask to include the encryption mask.
- Updates the protection_map entries to include the encryption mask so
that user-space allocations will automatically have the encryption mask
applied.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Toshimitsu Kani <toshi.kani@hpe.com>
Cc: kasan-dev@googlegroups.com
Cc: kvm@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-efi@vger.kernel.org
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/b36e952c4c39767ae7f0a41cf5345adf27438480.1500319216.git.thomas.lendacky@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add support to the early boot code to use Secure Memory Encryption (SME).
Since the kernel has been loaded into memory in a decrypted state, encrypt
the kernel in place and update the early pagetables with the memory
encryption mask so that new pagetable entries will use memory encryption.
The routines to set the encryption mask and perform the encryption are
stub routines for now with functionality to be added in a later patch.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Toshimitsu Kani <toshi.kani@hpe.com>
Cc: kasan-dev@googlegroups.com
Cc: kvm@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-efi@vger.kernel.org
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/e52ad781f085224bf835b3caff9aa3aee6febccb.1500319216.git.thomas.lendacky@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds support for 5-level paging during early boot.
It generalizes boot for 4- and 5-level paging on 64-bit systems with
compile-time switch between them.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20170606113133.22974-10-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With CONFIG_X86_5LEVEL=y, level 4 is no longer top level of page tables.
Let's give these variable more generic names: init_top_pgt and
early_top_pgt.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20170606113133.22974-9-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The patch write most of startup_64 logic in C.
This is preparation for 5-level paging enabling.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20170606113133.22974-8-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It doesn't really start a CPU but does a far jump to C code. So call it
that. Eliminate the unconditional JMP to it from secondary_startup_64()
but make the jump to C code piece part of secondary_startup_64()
instead.
Also, it doesn't need to be a global symbol either so make it a local
label. One less needlessly global symbol in the symbol table.
No functionality change.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170304095611.11355-1-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
start_cpu() pushes a text address on the stack so that stack traces from
idle tasks will show start_cpu() at the end. But it currently shows the
wrong function offset. It's more correct to show the address
immediately after the 'lretq' instruction.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/2cadd9f16c77da7ee7957bfc5e1c67928c23ca48.1481685203.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
start_cpu() pushes a text address on the stack so that stack traces from
idle tasks will show start_cpu() at the end. But it uses a call
instruction to do that, which is rather obtuse. Use a straightforward
push instead.
Suggested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/4d8a1952759721d42d1e62ba9e4a7e3ac5df8574.1481685203.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 boot updates from Ingo Molnar:
"Misc cleanups/simplifications by Borislav Petkov, Paul Bolle and Wei
Yang"
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot/64: Optimize fixmap page fixup
x86/boot: Simplify the GDTR calculation assembly code a bit
x86/boot/build: Remove always empty $(USERINCLUDE)
Single-stepping through head_64.S made me look at the fixmap page PTEs
fixup loop:
So we're going through the whole level2_fixmap_pgt 4K page, looking at
whether PAGE_PRESENT is set in those PTEs and add the delta between
where we're compiled to run and where we actually end up running.
However, if that delta is 0 (most cases) we go through all those 512
PTEs for no reason at all. Oh well, we add 0 but that's no reason to me.
Skipping that useless fixup gives us a boot speedup of 0.004 seconds in
my guest. Not a lot but considering how cheap it is, I'll take it. Here
is the printk time difference:
before:
...
[ 0.000000] tsc: Marking TSC unstable due to TSCs unsynchronized
[ 0.013590] Calibrating delay loop (skipped), value calculated using timer frequency..
8027.17 BogoMIPS (lpj=16054348)
[ 0.017094] pid_max: default: 32768 minimum: 301
...
after:
...
[ 0.000000] tsc: Marking TSC unstable due to TSCs unsynchronized
[ 0.009587] Calibrating delay loop (skipped), value calculated using timer frequency..
8026.86 BogoMIPS (lpj=16053724)
[ 0.013090] pid_max: default: 32768 minimum: 301
...
For the other two changes converting naked numbers to defines:
# arch/x86/kernel/head_64.o:
text data bss dec hex filename
1124 290864 4096 296084 48494 head_64.o.before
1124 290864 4096 296084 48494 head_64.o.after
md5:
87086e202588939296f66e892414ffe2 head_64.o.before.asm
87086e202588939296f66e892414ffe2 head_64.o.after.asm
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20161125111448.23623-1-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
... instead of naked numbers like the rest of the asm does in this file.
No code changed:
# arch/x86/kernel/head_64.o:
text data bss dec hex filename
1124 290864 4096 296084 48494 head_64.o.before
1124 290864 4096 296084 48494 head_64.o.after
md5:
87086e202588939296f66e892414ffe2 head_64.o.before.asm
87086e202588939296f66e892414ffe2 head_64.o.after.asm
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20161124210550.15025-1-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Thanks to all the recent x86 entry code refactoring, most tasks' kernel
stacks start at the same offset right below their saved pt_regs,
regardless of which syscall was used to enter the kernel. That creates
a nice convention which makes it straightforward to identify the end of
the stack, which can be useful for the unwinder to verify the stack is
sane.
However, the boot CPU's idle "swapper" task doesn't follow that
convention. Fix that by starting its stack at a sizeof(pt_regs) offset
from the end of the stack page.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nilay Vaish <nilayvaish@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/81aee3beb6ed88e44f1bea6986bb7b65c368f77a.1474480779.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The frame at the end of each idle task stack has a zeroed return
address. This is inconsistent with real task stacks, which have a real
return address at that spot. This inconsistency can be confusing for
stack unwinders. It also hides useful information about what asm code
was involved in calling into C.
Make it a real address by using the side effect of a call instruction to
push the instruction pointer on the stack.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nilay Vaish <nilayvaish@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/f59593ae7b15d5126f872b0a23143173d28aa32d.1474480779.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There are two different pieces of code for starting a CPU: start_cpu0()
and the end of secondary_startup_64(). They're identical except for the
stack setup. Combine the common parts into a shared start_cpu()
function.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nilay Vaish <nilayvaish@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1d692ffa62fcb3cc835a5b254e953f2d9bab3549.1474480779.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull kbuild updates from Michal Marek:
- EXPORT_SYMBOL for asm source by Al Viro.
This does bring a regression, because genksyms no longer generates
checksums for these symbols (CONFIG_MODVERSIONS). Nick Piggin is
working on a patch to fix this.
Plus, we are talking about functions like strcpy(), which rarely
change prototypes.
- Fixes for PPC fallout of the above by Stephen Rothwell and Nick
Piggin
- fixdep speedup by Alexey Dobriyan.
- preparatory work by Nick Piggin to allow architectures to build with
-ffunction-sections, -fdata-sections and --gc-sections
- CONFIG_THIN_ARCHIVES support by Stephen Rothwell
- fix for filenames with colons in the initramfs source by me.
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild: (22 commits)
initramfs: Escape colons in depfile
ppc: there is no clear_pages to export
powerpc/64: whitelist unresolved modversions CRCs
kbuild: -ffunction-sections fix for archs with conflicting sections
kbuild: add arch specific post-link Makefile
kbuild: allow archs to select link dead code/data elimination
kbuild: allow architectures to use thin archives instead of ld -r
kbuild: Regenerate genksyms lexer
kbuild: genksyms fix for typeof handling
fixdep: faster CONFIG_ search
ia64: move exports to definitions
sparc32: debride memcpy.S a bit
[sparc] unify 32bit and 64bit string.h
sparc: move exports to definitions
ppc: move exports to definitions
arm: move exports to definitions
s390: move exports to definitions
m68k: move exports to definitions
alpha: move exports to actual definitions
x86: move exports to actual definitions
...
This zeroed word has no apparent purpose, so remove it.
Brian Gerst says:
"FYI the word used to be the SS segment selector for the LSS
instruction, which isn't needed in 64-bit mode."
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Byungchul Park <byungchul.park@lge.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nilay Vaish <nilayvaish@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/b056855c295bbb3825b97c1e9f7958539a4d6cf2.1471535549.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The 'stack_start' variable is similar in usage to 'initial_code' and
'initial_gs': they're all stored in head_64.S and they're all updated by
SMP and ACPI suspend before starting a CPU.
Rename it to 'initial_stack' to be consistent with the others.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Byungchul Park <byungchul.park@lge.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nilay Vaish <nilayvaish@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/87063d773a3212051b77e17b0ee427f6582a5050.1471535549.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add the physical mapping in the list of randomized memory regions.
The physical memory mapping holds most allocations from boot and heap
allocators. Knowing the base address and physical memory size, an attacker
can deduce the PDE virtual address for the vDSO memory page. This attack
was demonstrated at CanSecWest 2016, in the following presentation:
"Getting Physical: Extreme Abuse of Intel Based Paged Systems":
https://github.com/n3k/CansecWest2016_Getting_Physical_Extreme_Abuse_of_Intel_Based_Paging_Systems/blob/master/Presentation/CanSec2016_Presentation.pdf
(See second part of the presentation).
The exploits used against Linux worked successfully against 4.6+ but
fail with KASLR memory enabled:
https://github.com/n3k/CansecWest2016_Getting_Physical_Extreme_Abuse_of_Intel_Based_Paging_Systems/tree/master/Demos/Linux/exploits
Similar research was done at Google leading to this patch proposal.
Variants exists to overwrite /proc or /sys objects ACLs leading to
elevation of privileges. These variants were tested against 4.6+.
The page offset used by the compressed kernel retains the static value
since it is not yet randomized during this boot stage.
Signed-off-by: Thomas Garnier <thgarnie@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Alexander Kuleshov <kuleshovmail@gmail.com>
Cc: Alexander Popov <alpopov@ptsecurity.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Lv Zheng <lv.zheng@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: kernel-hardening@lists.openwall.com
Cc: linux-doc@vger.kernel.org
Link: http://lkml.kernel.org/r/1466556426-32664-7-git-send-email-keescook@chromium.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
04633df0c4 ("x86/cpu: Call verify_cpu() after having entered long mode too")
added the call to verify_cpu() for sanitizing CPU configuration.
The latter uses the stack minimally and it can happen that we land in
startup_64() directly from a 64-bit bootloader. Then we want to use our
own, known good stack.
Do that.
APs don't need this as the trampoline sets up a stack for them.
Reported-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mika Penttilä <mika.penttila@nextfour.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1459434062-31055-1-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This removes a bunch of assembly and adds some C code instead. It
changes the actual printouts on both 32-bit and 64-bit kernels, but
they still seem okay.
Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: KVM list <kvm@vger.kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: xen-devel <Xen-devel@lists.xen.org>
Link: http://lkml.kernel.org/r/4085070316fc3ab29538d3fcfe282648d1d4ee2e.1459605520.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
C is nicer than asm.
Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: KVM list <kvm@vger.kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: xen-devel <Xen-devel@lists.xen.org>
Link: http://lkml.kernel.org/r/dd068269f8d59fe44e9e43a50d0efd67da65c2b5.1459605520.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
early_fixup_exception() is limited by the fact that it doesn't have a
real struct pt_regs. Change both the 32-bit and 64-bit asm and the
C code to pass and accept a real pt_regs.
Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: KVM list <kvm@vger.kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: xen-devel <Xen-devel@lists.xen.org>
Link: http://lkml.kernel.org/r/e3fb680fcfd5e23e38237e8328b64a25cc121d37.1459605520.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 boot updates from Ingo Molnar:
"Early command line options parsing enhancements from Dave Hansen, plus
minor cleanups and enhancements"
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Remove unused 'is_big_kernel' variable
x86/boot: Use proper array element type in memset() size calculation
x86/boot: Pass in size to early cmdline parsing
x86/boot: Simplify early command line parsing
x86/boot: Fix early command-line parsing when partial word matches
x86/boot: Fix early command-line parsing when matching at end
x86/boot: Simplify kernel load address alignment check
x86/boot: Micro-optimize reset_early_page_tables()
We are using %rax as temporary register to check the kernel
address alignment. We don't really have to since the TEST
instruction does not clobber the destination operand.
Suggested-by: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Alexander Kuleshov <kuleshovmail@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Alexander Popov <alpopov@ptsecurity.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1453531828-19291-1-git-send-email-kuleshovmail@gmail.com
Link: http://lkml.kernel.org/r/1453842730-28463-11-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
L3_PAGE_OFFSET was introduced in commit a6523748bd (paravirt/x86, 64-bit: move
__PAGE_OFFSET to leave a space for hypervisor), but has no users.
Signed-off-by: Alexander Kuleshov <kuleshovmail@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Link: http://lkml.kernel.org/r/1453810881-30622-1-git-send-email-kuleshovmail@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When we get loaded by a 64-bit bootloader, kernel entry point is
startup_64 in head_64.S. We don't trust any and all bootloaders because
some will fiddle with CPU configuration so we go ahead and massage each
CPU into sanity again.
For example, some dell BIOSes have this XD disable feature which set
IA32_MISC_ENABLE[34] and disable NX. This might be some dumb workaround
for other OSes but Linux sure doesn't need it.
A similar thing is present in the Surface 3 firmware - see
https://bugzilla.kernel.org/show_bug.cgi?id=106051 - which sets this bit
only on the BSP:
# rdmsr -a 0x1a0
400850089
850089
850089
850089
I know, right?!
There's not even an off switch in there.
So fix all those cases by sanitizing the 64-bit entry point too. For
that, make verify_cpu() callable in 64-bit mode also.
Requested-and-debugged-by: "H. Peter Anvin" <hpa@zytor.com>
Reported-and-tested-by: Bastien Nocera <bugzilla@hadess.net>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1446739076-21303-1-git-send-email-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Currently KASAN shadow region page tables created without
respect of physical offset (phys_base). This causes kernel halt
when phys_base is not zero.
So let's initialize KASAN shadow region page tables in
kasan_early_init() using __pa_nodebug() which considers
phys_base.
This patch also separates x86_64_start_kernel() from KASAN low
level details by moving kasan_map_early_shadow(init_level4_pgt)
into kasan_early_init().
Remove the comment before clear_bss() which stopped bringing
much profit to the code readability. Otherwise describing all
the new order dependencies would be too verbose.
Signed-off-by: Alexander Popov <alpopov@ptsecurity.com>
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Cc: <stable@vger.kernel.org> # 4.0+
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <adech.fo@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1435828178-10975-3-git-send-email-a.ryabinin@samsung.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The early_idt_handlers asm code generates an array of entry
points spaced nine bytes apart. It's not really clear from that
code or from the places that reference it what's going on, and
the code only works in the first place because GAS never
generates two-byte JMP instructions when jumping to global
labels.
Clean up the code to generate the correct array stride (member size)
explicitly. This should be considerably more robust against
screw-ups, as GAS will warn if a .fill directive has a negative
count. Using '. =' to advance would have been even more robust
(it would generate an actual error if it tried to move
backwards), but it would pad with nulls, confusing anyone who
tries to disassemble the code. The new scheme should be much
clearer to future readers.
While we're at it, improve the comments and rename the array and
common code.
Binutils may start relaxing jumps to non-weak labels. If so,
this change will fix our build, and we may need to backport this
change.
Before, on x86_64:
0000000000000000 <early_idt_handlers>:
0: 6a 00 pushq $0x0
2: 6a 00 pushq $0x0
4: e9 00 00 00 00 jmpq 9 <early_idt_handlers+0x9>
5: R_X86_64_PC32 early_idt_handler-0x4
...
48: 66 90 xchg %ax,%ax
4a: 6a 08 pushq $0x8
4c: e9 00 00 00 00 jmpq 51 <early_idt_handlers+0x51>
4d: R_X86_64_PC32 early_idt_handler-0x4
...
117: 6a 00 pushq $0x0
119: 6a 1f pushq $0x1f
11b: e9 00 00 00 00 jmpq 120 <early_idt_handler>
11c: R_X86_64_PC32 early_idt_handler-0x4
After:
0000000000000000 <early_idt_handler_array>:
0: 6a 00 pushq $0x0
2: 6a 00 pushq $0x0
4: e9 14 01 00 00 jmpq 11d <early_idt_handler_common>
...
48: 6a 08 pushq $0x8
4a: e9 d1 00 00 00 jmpq 120 <early_idt_handler_common>
4f: cc int3
50: cc int3
...
117: 6a 00 pushq $0x0
119: 6a 1f pushq $0x1f
11b: eb 03 jmp 120 <early_idt_handler_common>
11d: cc int3
11e: cc int3
11f: cc int3
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Binutils <binutils@sourceware.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H.J. Lu <hjl.tools@gmail.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/ac027962af343b0c599cbfcf50b945ad2ef3d7a8.1432336324.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
By the nature of the TEST operation, it is often possible to test
a narrower part of the operand:
"testl $3, mem" -> "testb $3, mem",
"testq $3, %rcx" -> "testb $3, %cl"
This results in shorter instructions, because the TEST instruction
has no sign-entending byte-immediate forms unlike other ALU ops.
Note that this change does not create any LCP (Length-Changing Prefix)
stalls, which happen when adding a 0x66 prefix, which happens when
16-bit immediates are used, which changes such TEST instructions:
[test_opcode] [modrm] [imm32]
to:
[0x66] [test_opcode] [modrm] [imm16]
where [imm16] has a *different length* now: 2 bytes instead of 4.
This confuses the decoder and slows down execution.
REX prefixes were carefully designed to almost never hit this case:
adding REX prefix does not change instruction length except MOVABS
and MOV [addr],RAX instruction.
This patch does not add instructions which would use a 0x66 prefix,
code changes in assembly are:
-48 f7 07 01 00 00 00 testq $0x1,(%rdi)
+f6 07 01 testb $0x1,(%rdi)
-48 f7 c1 01 00 00 00 test $0x1,%rcx
+f6 c1 01 test $0x1,%cl
-48 f7 c1 02 00 00 00 test $0x2,%rcx
+f6 c1 02 test $0x2,%cl
-41 f7 c2 01 00 00 00 test $0x1,%r10d
+41 f6 c2 01 test $0x1,%r10b
-48 f7 c1 04 00 00 00 test $0x4,%rcx
+f6 c1 04 test $0x4,%cl
-48 f7 c1 08 00 00 00 test $0x8,%rcx
+f6 c1 08 test $0x8,%cl
Linus further notes:
"There are no stalls from using 8-bit instruction forms.
Now, changing from 64-bit or 32-bit 'test' instructions to 8-bit ones
*could* cause problems if it ends up having forwarding issues, so that
instead of just forwarding the result, you end up having to wait for
it to be stable in the L1 cache (or possibly the register file). The
forwarding from the store buffer is simplest and most reliable if the
read is done at the exact same address and the exact same size as the
write that gets forwarded.
But that's true only if:
(a) the write was very recent and is still in the write queue. I'm
not sure that's the case here anyway.
(b) on at least most Intel microarchitectures, you have to test a
different byte than the lowest one (so forwarding a 64-bit write
to a 8-bit read ends up working fine, as long as the 8-bit read
is of the low 8 bits of the written data).
A very similar issue *might* show up for registers too, not just
memory writes, if you use 'testb' with a high-byte register (where
instead of forwarding the value from the original producer it needs to
go through the register file and then shifted). But it's mainly a
problem for store buffers.
But afaik, the way Denys changed the test instructions, neither of the
above issues should be true.
The real problem for store buffer forwarding tends to be "write 8
bits, read 32 bits". That can be really surprisingly expensive,
because the read ends up having to wait until the write has hit the
cacheline, and we might talk tens of cycles of latency here. But
"write 32 bits, read the low 8 bits" *should* be fast on pretty much
all x86 chips, afaik."
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Will Drewry <wad@chromium.org>
Link: http://lkml.kernel.org/r/1425675332-31576-1-git-send-email-dvlasenk@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds arch specific code for kernel address sanitizer.
16TB of virtual addressed used for shadow memory. It's located in range
[ffffec0000000000 - fffffc0000000000] between vmemmap and %esp fixup
stacks.
At early stage we map whole shadow region with zero page. Latter, after
pages mapped to direct mapping address range we unmap zero pages from
corresponding shadow (see kasan_map_shadow()) and allocate and map a real
shadow memory reusing vmemmap_populate() function.
Also replace __pa with __pa_nodebug before shadow initialized. __pa with
CONFIG_DEBUG_VIRTUAL=y make external function call (__phys_addr)
__phys_addr is instrumented, so __asan_load could be called before shadow
area initialized.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Konstantin Serebryany <kcc@google.com>
Cc: Dmitry Chernenkov <dmitryc@google.com>
Signed-off-by: Andrey Konovalov <adech.fo@gmail.com>
Cc: Yuri Gribov <tetra2005@gmail.com>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's an enum, not a #define, you can't use it in asm files.
Introduced in commit 5fa10196bd ("x86: Ignore NMIs that come in during
early boot"), and sadly I didn't compile-test things like I should have
before pushing out.
My weak excuse is that the x86 tree generally doesn't introduce stupid
things like this (and the ARM pull afterwards doesn't cause me to do a
compile-test either, since I don't cross-compile).
Cc: Don Zickus <dzickus@redhat.com>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don Zickus reports:
A customer generated an external NMI using their iLO to test kdump
worked. Unfortunately, the machine hung. Disabling the nmi_watchdog
made things work.
I speculated the external NMI fired, caused the machine to panic (as
expected) and the perf NMI from the watchdog came in and was latched.
My guess was this somehow caused the hang.
----
It appears that the latched NMI stays latched until the early page
table generation on 64 bits, which causes exceptions to happen which
end in IRET, which re-enable NMI. Therefore, ignore NMIs that come in
during early execution, until we have proper exception handling.
Reported-and-tested-by: Don Zickus <dzickus@redhat.com>
Link: http://lkml.kernel.org/r/1394221143-29713-1-git-send-email-dzickus@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.5+, older with some backport effort
