topa_entry->base is a bit-field. Bit-fields are not promoted to a 64-bit
type, even if the underlying type is 64-bit, and so, if necessary, must
be cast to a larger type when calculations are done.
Fix a topa_entry->base address calculation by adding a cast.
Without the cast, the address was limited to 36-bits i.e. 64GiB.
The address calculation is used on systems that do not support Multiple
Entry ToPA (only Broadwell), and affects physical addresses on or above
64GiB. Instead of writing to the correct address, the address comprising
the first 36 bits would be written to.
Intel PT snapshot and sampling modes are not affected.
Fixes: 52ca9ced3f ("perf/x86/intel/pt: Add Intel PT PMU driver")
Reported-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240624201101.60186-3-adrian.hunter@intel.com
topa_entry->base needs to store a pfn. It obviously needs to be
large enough to store the largest possible x86 pfn which is
MAXPHYADDR-PAGE_SIZE (52-12). So it is 4 bits too small.
Increase the size of topa_entry->base from 36 bits to 40 bits.
Note, systems where physical addresses can be 256TiB or more are affected.
[ Adrian: Amend commit message as suggested by Dave Hansen ]
Fixes: 52ca9ced3f ("perf/x86/intel/pt: Add Intel PT PMU driver")
Signed-off-by: Marco Cavenati <cavenati.marco@gmail.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240624201101.60186-2-adrian.hunter@intel.com
Unknown uncore PMON types can be found in both SPR and EMR with HBM or
CXL.
$ls /sys/devices/ | grep type
uncore_type_12_16
uncore_type_12_18
uncore_type_12_2
uncore_type_12_4
uncore_type_12_6
uncore_type_12_8
uncore_type_13_17
uncore_type_13_19
uncore_type_13_3
uncore_type_13_5
uncore_type_13_7
uncore_type_13_9
The unknown PMON types are HBM and CXL PMON. Except for the name, the
other information regarding the HBM and CXL PMON counters can be
retrieved via the discovery table. Add them into the uncores tables for
SPR and EMR.
The event config registers for all CXL related units are 8-byte apart.
Add SPR_UNCORE_MMIO_OFFS8_COMMON_FORMAT to specially handle it.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Yunying Sun <yunying.sun@intel.com>
Link: https://lore.kernel.org/r/20240614134631.1092359-9-kan.liang@linux.intel.com
The unit control and ID information are retrieved from the unit control
RB tree. No one uses the old structure anymore. Remove them.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Yunying Sun <yunying.sun@intel.com>
Link: https://lore.kernel.org/r/20240614134631.1092359-8-kan.liang@linux.intel.com
The unit control RB tree has the unit control and unit ID information
for all the PCI units. Use them to replace the box_ctls/pci_offsets to
get an accurate unit control address for PCI uncore units.
The UPI/M3UPI units in the discovery table are ignored. Please see the
commit 65248a9a9e ("perf/x86/uncore: Add a quirk for UPI on SPR").
Manually allocate a unit control RB tree for UPI/M3UPI.
Add cleanup_extra_boxes to release such manual allocation.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Yunying Sun <yunying.sun@intel.com>
Link: https://lore.kernel.org/r/20240614134631.1092359-7-kan.liang@linux.intel.com
The unit control RB tree has the unit control and unit ID information
for all the MSR units. Use them to replace the box_ctl and
uncore_msr_box_ctl() to get an accurate unit control address for MSR
uncore units.
Add intel_generic_uncore_assign_hw_event(), which utilizes the accurate
unit control address from the unit control RB tree to calculate the
config_base and event_base.
The unit id related information should be retrieved from the unit
control RB tree as well.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Yunying Sun <yunying.sun@intel.com>
Link: https://lore.kernel.org/r/20240614134631.1092359-6-kan.liang@linux.intel.com
The unit control RB tree has the unit control and unit ID information
for all the units. Use it to replace the box_ctls/mmio_offsets to get
an accurate unit control address for MMIO uncore units.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Yunying Sun <yunying.sun@intel.com>
Link: https://lore.kernel.org/r/20240614134631.1092359-5-kan.liang@linux.intel.com
The box_ids only save the unit ID for the first die. If a unit, e.g., a
CXL unit, doesn't exist in the first die. The unit ID cannot be
retrieved.
The unit control RB tree also stores the unit ID information.
Retrieve the unit ID from the unit control RB tree
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Yunying Sun <yunying.sun@intel.com>
Link: https://lore.kernel.org/r/20240614134631.1092359-4-kan.liang@linux.intel.com
The cpumask of some uncore units, e.g., CXL uncore units, may be wrong
under some configurations. Perf may access an uncore counter of a
non-existent uncore unit.
The uncore driver assumes that all uncore units are symmetric among
dies. A global cpumask is shared among all uncore PMUs. However, some
CXL uncore units may only be available on some dies.
A per PMU cpumask is introduced to track the CPU mask of this PMU.
The driver searches the unit control RB tree to check whether the PMU is
available on a given die, and updates the per PMU cpumask accordingly.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Yunying Sun <yunying.sun@intel.com>
Link: https://lore.kernel.org/r/20240614134631.1092359-3-kan.liang@linux.intel.com
The unit control address of some CXL units may be wrongly calculated
under some configuration on a EMR machine.
The current implementation only saves the unit control address of the
units from the first die, and the first unit of the rest of dies. Perf
assumed that the units from the other dies have the same offset as the
first die. So the unit control address of the rest of the units can be
calculated. However, the assumption is wrong, especially for the CXL
units.
Introduce an RB tree for each uncore type to save the unit control
address and three kinds of ID information (unit ID, PMU ID, and die ID)
for all units.
The unit ID is a physical ID of a unit.
The PMU ID is a logical ID assigned to a unit. The logical IDs start
from 0 and must be contiguous. The physical ID and the logical ID are
1:1 mapping. The units with the same physical ID in different dies share
the same PMU.
The die ID indicates which die a unit belongs to.
The RB tree can be searched by two different keys (unit ID or PMU ID +
die ID). During the RB tree setup, the unit ID is used as a key to look
up the RB tree. The perf can create/assign a proper PMU ID to the unit.
Later, after the RB tree is setup, PMU ID + die ID is used as a key to
look up the RB tree to fill the cpumask of a PMU. It's used more
frequently, so PMU ID + die ID is compared in the unit_less().
The uncore_find_unit() has to be O(N). But the RB tree setup only occurs
once during the driver load time. It should be acceptable.
Compared with the current implementation, more space is required to save
the information of all units. The extra size should be acceptable.
For example, on EMR, there are 221 units at most. For a 2-socket machine,
the extra space is ~6KB at most.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20240614134631.1092359-2-kan.liang@linux.intel.com
Yue and Xingwei reported a jump label failure. It's caused by the lack of
serialization in set_attr_rdpmc():
CPU0 CPU1
Assume: x86_pmu.attr_rdpmc == 0
if (val != x86_pmu.attr_rdpmc) {
if (val == 0)
...
else if (x86_pmu.attr_rdpmc == 0)
static_branch_dec(&rdpmc_never_available_key);
if (val != x86_pmu.attr_rdpmc) {
if (val == 0)
...
else if (x86_pmu.attr_rdpmc == 0)
FAIL, due to imbalance ---> static_branch_dec(&rdpmc_never_available_key);
The reported BUG() is a consequence of the above and of another bug in the
jump label core code. The core code needs a separate fix, but that cannot
prevent the imbalance problem caused by set_attr_rdpmc().
Prevent this by serializing set_attr_rdpmc() locally.
Fixes: a66734297f ("perf/x86: Add /sys/devices/cpu/rdpmc=2 to allow rdpmc for all tasks")
Closes: https://lore.kernel.org/r/CAEkJfYNzfW1vG=ZTMdz_Weoo=RXY1NDunbxnDaLyj8R4kEoE_w@mail.gmail.com
Reported-by: Yue Sun <samsun1006219@gmail.com>
Reported-by: Xingwei Lee <xrivendell7@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20240610124406.359476013@linutronix.de
Fix the warning from 'make C=1 W=1':
WARNING: modpost: missing MODULE_DESCRIPTION() in arch/x86/events/rapl.o
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Link: https://lore.kernel.org/r/20240530-md-arch-x86-events-v1-1-e45ffa8af99f@quicinc.com
New CPU #defines encode vendor and family as well as model.
Update INTEL_CPU_DESC() to work with vendor/family/model.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/all/20240520224620.9480-34-tony.luck%40intel.com
Here is the small set of driver core and kernfs changes for 6.10-rc1.
Nothing major here at all, just a small set of changes for some driver
core apis, and minor fixups. Included in here are:
- sysfs_bin_attr_simple_read() helper added and used
- device_show_string() helper added and used
All usages of these were acked by the various maintainers. Also in here
are:
- kernfs minor cleanup
- removed unused functions
- typo fix in documentation
- pay attention to sysfs_create_link() failures in module.c finally.
All of these have been in linux-next for a very long time with no
reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZk3+hQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylfTwCfUyHWkDZuZ7ehdtjzfmcd4EKZBK8An3AAV99G
ox8PXMxuFTaUEdT/69FQ
=2sEo
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the small set of driver core and kernfs changes for 6.10-rc1.
Nothing major here at all, just a small set of changes for some driver
core apis, and minor fixups. Included in here are:
- sysfs_bin_attr_simple_read() helper added and used
- device_show_string() helper added and used
All usages of these were acked by the various maintainers. Also in
here are:
- kernfs minor cleanup
- removed unused functions
- typo fix in documentation
- pay attention to sysfs_create_link() failures in module.c finally
All of these have been in linux-next for a very long time with no
reported problems"
* tag 'driver-core-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
device property: Fix a typo in the description of device_get_child_node_count()
kernfs: mount: Remove unnecessary ‘NULL’ values from knparent
scsi: Use device_show_string() helper for sysfs attributes
platform/x86: Use device_show_string() helper for sysfs attributes
perf: Use device_show_string() helper for sysfs attributes
IB/qib: Use device_show_string() helper for sysfs attributes
hwmon: Use device_show_string() helper for sysfs attributes
driver core: Add device_show_string() helper for sysfs attributes
treewide: Use sysfs_bin_attr_simple_read() helper
sysfs: Add sysfs_bin_attr_simple_read() helper
module: don't ignore sysfs_create_link() failures
driver core: Remove unused platform_notify, platform_notify_remove
Replace this pattern in events/amd/{un,}core.c:
cmpxchg(*ptr, old, new) == old
... with the simpler and faster:
try_cmpxchg(*ptr, &old, new)
The x86 CMPXCHG instruction returns success in the ZF flag, so this change
saves a compare after the CMPXCHG.
No functional change intended.
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20240425101708.5025-1-ubizjak@gmail.com
Use of this structure was removed in:
8f2a28c585 ("perf/x86/cstate: Use new probe function")
Remove the now stale type as well.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Deduplicate sysfs ->show() callbacks which expose a string at a static
memory location. Use the newly introduced device_show_string() helper
in the driver core instead by declaring those sysfs attributes with
DEVICE_STRING_ATTR_RO().
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/3a297850312b4ecb62d6872121de04496900f502.1713608122.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AMD CPUs have the scope of RAPL energy-pkg event as package, whereas
Intel Cascade Lake CPUs have the scope as die.
To account for the difference in the energy-pkg event scope between AMD
and Intel CPUs, give more generic and semantically correct names to the
maxdie and dieid variables.
No functional change.
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: K Prateek Nayak <kprateek.nayak@amd.com>
Link: https://lore.kernel.org/r/20240502095115.177713-2-Dhananjay.Ugwekar@amd.com
New CPU #defines encode vendor and family as well as model.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/all/20240424181503.41614-1-tony.luck%40intel.com
New CPU #defines encode vendor and family as well as model.
[ bp: Squash *three* uncore patches into one. ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/all/20240424181501.41557-1-tony.luck%40intel.com
without OBJECT_FILES_NON_STANDARD. This fixes a warning
"Unpatched return thunk in use. This should not happen!" when running
KVM selftests.
* Fix a mostly benign bug in the gfn_to_pfn_cache infrastructure where KVM
would allow userspace to refresh the cache with a bogus GPA. The bug has
existed for quite some time, but was exposed by a new sanity check added in
6.9 (to ensure a cache is either GPA-based or HVA-based).
* Drop an unused param from gfn_to_pfn_cache_invalidate_start() that got left
behind during a 6.9 cleanup.
* Fix a math goof in x86's hugepage logic for KVM_SET_MEMORY_ATTRIBUTES that
results in an array overflow (detected by KASAN).
* Fix a bug where KVM incorrectly clears root_role.direct when userspace sets
guest CPUID.
* Fix a dirty logging bug in the where KVM fails to write-protect SPTEs used
by a nested guest, if KVM is using Page-Modification Logging and the nested
hypervisor is NOT using EPT.
x86 PMU:
* Drop support for virtualizing adaptive PEBS, as KVM's implementation is
architecturally broken without an obvious/easy path forward, and because
exposing adaptive PEBS can leak host LBRs to the guest, i.e. can leak
host kernel addresses to the guest.
* Set the enable bits for general purpose counters in PERF_GLOBAL_CTRL at
RESET time, as done by both Intel and AMD processors.
* Disable LBR virtualization on CPUs that don't support LBR callstacks, as
KVM unconditionally uses PERF_SAMPLE_BRANCH_CALL_STACK when creating the
perf event, and would fail on such CPUs.
Tests:
* Fix a flaw in the max_guest_memory selftest that results in it exhausting
the supply of ucall structures when run with more than 256 vCPUs.
* Mark KVM_MEM_READONLY as supported for RISC-V in set_memory_region_test.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmYjdqcUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroPNRAgAh1AdKBAWnq9bFN2Np1kSAcRAk3bs
REDq/0iD1T9TvIwEmE1lHaRuqvCSO15WW+DKvbs7TS8zA0DyY7X/x8sIIy5YzZ5C
bQ+JXiqk55OAj0sPskBpCvE5qEreuU8qAit57+8OseKWs57EICvJjrfsRnHlmIub
pgGas3I42LjIgsuZRr2kjv+GrvaiikW+wWK6sq3CvPzTtHV196d26AK5l4NOoLkY
0FTbBIYUSJ7wxs92xuTed5mZ7JFZdsa5DVMXF5MRZ9W6g2vZCLbqCNRddRhSAsl0
gKmqZkuPTB7AnGQbJ2h/aKFT0ydsguzqbbKq62sK7ft5f1CUlbp9luDC9w==
=99rq
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"This is a bit on the large side, mostly due to two changes:
- Changes to disable some broken PMU virtualization (see below for
details under "x86 PMU")
- Clean up SVM's enter/exit assembly code so that it can be compiled
without OBJECT_FILES_NON_STANDARD. This fixes a warning "Unpatched
return thunk in use. This should not happen!" when running KVM
selftests.
Everything else is small bugfixes and selftest changes:
- Fix a mostly benign bug in the gfn_to_pfn_cache infrastructure
where KVM would allow userspace to refresh the cache with a bogus
GPA. The bug has existed for quite some time, but was exposed by a
new sanity check added in 6.9 (to ensure a cache is either
GPA-based or HVA-based).
- Drop an unused param from gfn_to_pfn_cache_invalidate_start() that
got left behind during a 6.9 cleanup.
- Fix a math goof in x86's hugepage logic for
KVM_SET_MEMORY_ATTRIBUTES that results in an array overflow
(detected by KASAN).
- Fix a bug where KVM incorrectly clears root_role.direct when
userspace sets guest CPUID.
- Fix a dirty logging bug in the where KVM fails to write-protect
SPTEs used by a nested guest, if KVM is using Page-Modification
Logging and the nested hypervisor is NOT using EPT.
x86 PMU:
- Drop support for virtualizing adaptive PEBS, as KVM's
implementation is architecturally broken without an obvious/easy
path forward, and because exposing adaptive PEBS can leak host LBRs
to the guest, i.e. can leak host kernel addresses to the guest.
- Set the enable bits for general purpose counters in
PERF_GLOBAL_CTRL at RESET time, as done by both Intel and AMD
processors.
- Disable LBR virtualization on CPUs that don't support LBR
callstacks, as KVM unconditionally uses
PERF_SAMPLE_BRANCH_CALL_STACK when creating the perf event, and
would fail on such CPUs.
Tests:
- Fix a flaw in the max_guest_memory selftest that results in it
exhausting the supply of ucall structures when run with more than
256 vCPUs.
- Mark KVM_MEM_READONLY as supported for RISC-V in
set_memory_region_test"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (30 commits)
KVM: Drop unused @may_block param from gfn_to_pfn_cache_invalidate_start()
KVM: selftests: Add coverage of EPT-disabled to vmx_dirty_log_test
KVM: x86/mmu: Fix and clarify comments about clearing D-bit vs. write-protecting
KVM: x86/mmu: Remove function comments above clear_dirty_{gfn_range,pt_masked}()
KVM: x86/mmu: Write-protect L2 SPTEs in TDP MMU when clearing dirty status
KVM: x86/mmu: Precisely invalidate MMU root_role during CPUID update
KVM: VMX: Disable LBR virtualization if the CPU doesn't support LBR callstacks
perf/x86/intel: Expose existence of callback support to KVM
KVM: VMX: Snapshot LBR capabilities during module initialization
KVM: x86/pmu: Do not mask LVTPC when handling a PMI on AMD platforms
KVM: x86: Snapshot if a vCPU's vendor model is AMD vs. Intel compatible
KVM: x86: Stop compiling vmenter.S with OBJECT_FILES_NON_STANDARD
KVM: SVM: Create a stack frame in __svm_sev_es_vcpu_run()
KVM: SVM: Save/restore args across SEV-ES VMRUN via host save area
KVM: SVM: Save/restore non-volatile GPRs in SEV-ES VMRUN via host save area
KVM: SVM: Clobber RAX instead of RBX when discarding spec_ctrl_intercepted
KVM: SVM: Drop 32-bit "support" from __svm_sev_es_vcpu_run()
KVM: SVM: Wrap __svm_sev_es_vcpu_run() with #ifdef CONFIG_KVM_AMD_SEV
KVM: SVM: Create a stack frame in __svm_vcpu_run() for unwinding
KVM: SVM: Remove a useless zeroing of allocated memory
...
Add a "has_callstack" field to the x86_pmu_lbr structure used to pass
information to KVM, and set it accordingly in x86_perf_get_lbr(). KVM
will use has_callstack to avoid trying to create perf LBR events with
PERF_SAMPLE_BRANCH_CALL_STACK on CPUs that don't support callstacks.
Reviewed-by: Mingwei Zhang <mizhang@google.com>
Link: https://lore.kernel.org/r/20240307011344.835640-3-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
On x86 each struct cpu_hw_events maintains a table for counter assignment but
it missed to update one for the deleted event in x86_pmu_del(). This
can make perf_clear_dirty_counters() reset used counter if it's called
before event scheduling or enabling. Then it would return out of range
data which doesn't make sense.
The following code can reproduce the problem.
$ cat repro.c
#include <pthread.h>
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <linux/perf_event.h>
#include <sys/ioctl.h>
#include <sys/mman.h>
#include <sys/syscall.h>
struct perf_event_attr attr = {
.type = PERF_TYPE_HARDWARE,
.config = PERF_COUNT_HW_CPU_CYCLES,
.disabled = 1,
};
void *worker(void *arg)
{
int cpu = (long)arg;
int fd1 = syscall(SYS_perf_event_open, &attr, -1, cpu, -1, 0);
int fd2 = syscall(SYS_perf_event_open, &attr, -1, cpu, -1, 0);
void *p;
do {
ioctl(fd1, PERF_EVENT_IOC_ENABLE, 0);
p = mmap(NULL, 4096, PROT_READ, MAP_SHARED, fd1, 0);
ioctl(fd2, PERF_EVENT_IOC_ENABLE, 0);
ioctl(fd2, PERF_EVENT_IOC_DISABLE, 0);
munmap(p, 4096);
ioctl(fd1, PERF_EVENT_IOC_DISABLE, 0);
} while (1);
return NULL;
}
int main(void)
{
int i;
int n = sysconf(_SC_NPROCESSORS_ONLN);
pthread_t *th = calloc(n, sizeof(*th));
for (i = 0; i < n; i++)
pthread_create(&th[i], NULL, worker, (void *)(long)i);
for (i = 0; i < n; i++)
pthread_join(th[i], NULL);
free(th);
return 0;
}
And you can see the out of range data using perf stat like this.
Probably it'd be easier to see on a large machine.
$ gcc -o repro repro.c -pthread
$ ./repro &
$ sudo perf stat -A -I 1000 2>&1 | awk '{ if (length($3) > 15) print }'
1.001028462 CPU6 196,719,295,683,763 cycles # 194290.996 GHz (71.54%)
1.001028462 CPU3 396,077,485,787,730 branch-misses # 15804359784.80% of all branches (71.07%)
1.001028462 CPU17 197,608,350,727,877 branch-misses # 14594186554.56% of all branches (71.22%)
2.020064073 CPU4 198,372,472,612,140 cycles # 194681.113 GHz (70.95%)
2.020064073 CPU6 199,419,277,896,696 cycles # 195720.007 GHz (70.57%)
2.020064073 CPU20 198,147,174,025,639 cycles # 194474.654 GHz (71.03%)
2.020064073 CPU20 198,421,240,580,145 stalled-cycles-frontend # 100.14% frontend cycles idle (70.93%)
3.037443155 CPU4 197,382,689,923,416 cycles # 194043.065 GHz (71.30%)
3.037443155 CPU20 196,324,797,879,414 cycles # 193003.773 GHz (71.69%)
3.037443155 CPU5 197,679,956,608,205 stalled-cycles-backend # 1315606428.66% backend cycles idle (71.19%)
3.037443155 CPU5 198,571,860,474,851 instructions # 13215422.58 insn per cycle
It should move the contents in the cpuc->assign as well.
Fixes: 5471eea5d3 ("perf/x86: Reset the dirty counter to prevent the leak for an RDPMC task")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240306061003.1894224-1-namhyung@kernel.org
The MSR_PEBS_DATA_CFG MSR register is used to configure which data groups
should be generated into a PEBS record, and it's shared among all counters.
If there are different configurations among counters, perf combines all the
configurations.
The first perf command as below requires a complete PEBS record
(including memory info, GPRs, XMMs, and LBRs). The second perf command
only requires a basic group. However, after the second perf command is
running, the MSR_PEBS_DATA_CFG register is cleared. Only a basic group is
generated in a PEBS record, which is wrong. The required information
for the first perf command is missed.
$ perf record --intr-regs=AX,SP,XMM0 -a -C 8 -b -W -d -c 100000003 -o /dev/null -e cpu/event=0xd0,umask=0x81/upp &
$ sleep 5
$ perf record --per-thread -c 1 -e cycles:pp --no-timestamp --no-tid taskset -c 8 ./noploop 1000
The first PEBS event is a system-wide PEBS event. The second PEBS event
is a per-thread event. When the thread is scheduled out, the
intel_pmu_pebs_del() function is invoked to update the PEBS state.
Since the system-wide event is still available, the cpuc->n_pebs is 1.
The cpuc->pebs_data_cfg is cleared. The data configuration for the
system-wide PEBS event is lost.
The (cpuc->n_pebs == 1) check was introduced in commit:
b6a32f023f ("perf/x86: Fix PEBS threshold initialization")
At that time, it indeed didn't hurt whether the state was updated
during the removal, because only the threshold is updated.
The calculation of the threshold takes the last PEBS event into
account.
However, since commit:
b752ea0c28 ("perf/x86/intel/ds: Flush PEBS DS when changing PEBS_DATA_CFG")
we delay the threshold update, and clear the PEBS data config, which triggers
the bug.
The PEBS data config update scope should not be shrunk during removal.
[ mingo: Improved the changelog & comments. ]
Fixes: b752ea0c28 ("perf/x86/intel/ds: Flush PEBS DS when changing PEBS_DATA_CFG")
Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240401133320.703971-1-kan.liang@linux.intel.com
Now that it's possible to capture LBR on AMD CPU from BPF at arbitrary
point, there is no reason to artificially limit this feature to just
sampling events. So corresponding check is removed. AFAIU, there is no
correctness implications of doing this (and it was possible to bypass
this check by just setting perf_event's sample_period to 1 anyways, so
it doesn't guard all that much).
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Sandipan Das <sandipan.das@amd.com>
Link: https://lore.kernel.org/r/20240402022118.1046049-5-andrii@kernel.org
Upstream commit c22ac2a3d4 ("perf: Enable branch record for software
events") added ability to capture LBR (Last Branch Records) on Intel CPUs
from inside BPF program at pretty much any arbitrary point. This is
extremely useful capability that allows to figure out otherwise
hard to debug problems, because LBR is now available based on some
application-defined conditions, not just hardware-supported events.
'retsnoop' is one such tool that takes a huge advantage of this
functionality and has proved to be an extremely useful tool in
practice:
https://github.com/anakryiko/retsnoop
Now, AMD Zen4 CPUs got support for similar LBR functionality, but
necessary wiring inside the kernel is not yet setup. This patch seeks to
rectify this and follows a similar approach to the original patch
for Intel CPUs. We implement an AMD-specific callback set to be called
through perf_snapshot_branch_stack static call.
Previous preparatory patches ensured that amd_pmu_core_disable_all() and
__amd_pmu_lbr_disable() will be completely inlined and will have no
branches, so LBR snapshot contamination will be minimized.
This was tested on AMD Bergamo CPU and worked well when utilized from
the aforementioned retsnoop tool.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Sandipan Das <sandipan.das@amd.com>
Link: https://lore.kernel.org/r/20240402022118.1046049-4-andrii@kernel.org
In the following patches we will enable LBR capture on AMD CPUs at
arbitrary point in time, which means that LBR recording won't be frozen
by hardware automatically as part of hardware overflow event. So we need
to take care to minimize amount of branches and function calls/returns
on the path to freezing LBR, minimizing LBR snapshot altering as much as
possible.
As such, split out LBR disabling logic from the sanity checking logic
inside amd_pmu_lbr_disable_all(). This will ensure that no branches are
taken before LBR is frozen in the functionality added in the next patch.
Use __always_inline to also eliminate any possible function calls.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Sandipan Das <sandipan.das@amd.com>
Link: https://lore.kernel.org/r/20240402022118.1046049-3-andrii@kernel.org
In the following patches we will enable LBR capture on AMD CPUs at
arbitrary point in time, which means that LBR recording won't be frozen
by hardware automatically as part of hardware overflow event. So we need
to take care to minimize amount of branches and function calls/returns
on the path to freezing LBR, minimizing LBR snapshot altering as much as
possible.
amd_pmu_core_disable_all() is one of the functions on this path, and is
already marked as __always_inline. But it calls amd_pmu_set_global_ctl()
which is marked as just inline. So to guarantee no function call will
be generated thoughout mark amd_pmu_set_global_ctl() as __always_inline
as well.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Sandipan Das <sandipan.das@amd.com>
Link: https://lore.kernel.org/r/20240402022118.1046049-2-andrii@kernel.org
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmYJ1nceHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGzPkH/jQ9hL1zS3XS+wJw
GthWkLl70quCueWkLaOYdhfPwJpRDVIrr7A533q1Hxp35nWx6bEJpmvBHys8Dm/x
5OOf595voL7UhdY+93k0IRyJBSMApBgW83AO6vqndpld95TrOxItdvlnpuXiqLxn
5S4vf5LSWE7B2k0iWq5Uv6UnBwQ19F9SB6d0ujLHYBp5VcwDuctIPrD+2+XYKBBf
/PWZtUgn4FeL6Ez1MJGs2qGSK8vxalqozqsrIr/LAQayhwGA+OM7Q/hqVQmjbek7
QdGJPRMsngbq+QxbMzKA5q57tM7RKnrZgnOi3hC/FWpHNXPPHdeBfnPqpRw+ovJA
qLvEBI0=
=2ioy
-----END PGP SIGNATURE-----
Merge tag 'v6.9-rc2' into perf/core, to pick up dependent commits
Pick up fixes that followup patches are going to depend on.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add the "ref-cycles" event for AMD processors based on Zen 4 and later
microarchitectures. The backing event is based on PMCx120 which counts
cycles not in halt state in P0 frequency (same as MPERF).
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/089155f19f7c7e65aeb1caa727a882e2ca9b8b04.1711352180.git.sandipan.das@amd.com
AMD processors based on Zen 2 and later microarchitectures do not
support PMCx087 (instruction pipe stalls) which is used as the backing
event for "stalled-cycles-frontend" and "stalled-cycles-backend".
Use PMCx0A9 (cycles where micro-op queue is empty) instead to count
frontend stalls and remove the entry for backend stalls since there
is no direct replacement.
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Ian Rogers <irogers@google.com>
Fixes: 3fe3331bb2 ("perf/x86/amd: Add event map for AMD Family 17h")
Link: https://lore.kernel.org/r/03d7fc8fa2a28f9be732116009025bdec1b3ec97.1711352180.git.sandipan.das@amd.com
Currently, the LBR code assumes that LBR Freeze is supported on all processors
when X86_FEATURE_AMD_LBR_V2 is available i.e. CPUID leaf 0x80000022[EAX]
bit 1 is set. This is incorrect as the availability of the feature is
additionally dependent on CPUID leaf 0x80000022[EAX] bit 2 being set,
which may not be set for all Zen 4 processors.
Define a new feature bit for LBR and PMC freeze and set the freeze enable bit
(FLBRI) in DebugCtl (MSR 0x1d9) conditionally.
It should still be possible to use LBR without freeze for profile-guided
optimization of user programs by using an user-only branch filter during
profiling. When the user-only filter is enabled, branches are no longer
recorded after the transition to CPL 0 upon PMI arrival. When branch
entries are read in the PMI handler, the branch stack does not change.
E.g.
$ perf record -j any,u -e ex_ret_brn_tkn ./workload
Since the feature bit is visible under flags in /proc/cpuinfo, it can be
used to determine the feasibility of use-cases which require LBR Freeze
to be supported by the hardware such as profile-guided optimization of
kernels.
Fixes: ca5b7c0d96 ("perf/x86/amd/lbr: Add LbrExtV2 branch record support")
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/69a453c97cfd11c6f2584b19f937fe6df741510f.1711091584.git.sandipan.das@amd.com
This is an effort to get rid of all multiplications from allocation
functions in order to prevent integer overflows:
https://www.kernel.org/doc/html/latest/process/deprecated.html#open-coded-arithmetic-in-allocator-argumentshttps://github.com/KSPP/linux/issues/160
As the "rapl_pmus" variable is a pointer to "struct rapl_pmus" and
this structure ends in a flexible array:
struct rapl_pmus {
[...]
struct rapl_pmu *pmus[] __counted_by(maxdie);
};
the preferred way in the kernel is to use the struct_size() helper to
do the arithmetic instead of the calculation "size + count * size" in
the kzalloc() function.
This way, the code is more readable and safer.
Signed-off-by: Erick Archer <erick.archer@gmx.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20240317164442.6729-1-erick.archer@gmx.com
When bringing a CPU online, some of the PMC and LBR related registers
are reset. The same is done when a CPU is taken offline although that
is unnecessary. This currently happens in the "cpu_dead" callback which
is also incorrect as the callback runs on a control CPU instead of the
one that is being taken offline. This also affects hibernation and
suspend to RAM on some platforms as reported in the link below.
Fixes: 21d59e3e2c ("perf/x86/amd/core: Detect PerfMonV2 support")
Reported-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/550a026764342cf7e5812680e3e2b91fe662b5ac.1706526029.git.sandipan.das@amd.com
The Revision Guide for AMD Family 19h Model 10-1Fh processors declares
Erratum 1452 which states that non-branch entries may erroneously be
recorded in the Last Branch Record (LBR) stack with the valid and
spec bits set.
Such entries can be recognized by inspecting bit 61 of the corresponding
LastBranchStackToIp register. This bit is currently reserved but if found
to be set, the associated branch entry should be discarded.
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://bugzilla.kernel.org/attachment.cgi?id=305518
Link: https://lore.kernel.org/r/3ad2aa305f7396d41a40e3f054f740d464b16b7f.1706526029.git.sandipan.das@amd.com
cure Sparse warnings.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=0eJ7
-----END PGP SIGNATURE-----
Merge tag 'x86-cleanups-2024-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cleanups from Ingo Molnar:
"Misc cleanups, including a large series from Thomas Gleixner to cure
sparse warnings"
* tag 'x86-cleanups-2024-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/nmi: Drop unused declaration of proc_nmi_enabled()
x86/callthunks: Use EXPORT_PER_CPU_SYMBOL_GPL() for per CPU variables
x86/cpu: Provide a declaration for itlb_multihit_kvm_mitigation
x86/cpu: Use EXPORT_PER_CPU_SYMBOL_GPL() for x86_spec_ctrl_current
x86/uaccess: Add missing __force to casts in __access_ok() and valid_user_address()
x86/percpu: Cure per CPU madness on UP
smp: Consolidate smp_prepare_boot_cpu()
x86/msr: Add missing __percpu annotations
x86/msr: Prepare for including <linux/percpu.h> into <asm/msr.h>
perf/x86/amd/uncore: Fix __percpu annotation
x86/nmi: Remove an unnecessary IS_ENABLED(CONFIG_SMP)
x86/apm_32: Remove dead function apm_get_battery_status()
x86/insn-eval: Fix function param name in get_eff_addr_sib()
To clean up the per CPU insanity of UP which causes sparse to be rightfully
unhappy and prevents the usage of the generic per CPU accessors on cpu_info
it is necessary to include <linux/percpu.h> into <asm/msr.h>.
Including <linux/percpu.h> into <asm/msr.h> is impossible because it ends
up in header dependency hell. The problem is that <asm/processor.h>
includes <asm/msr.h>. The inclusion of <linux/percpu.h> results in a
compile fail where the compiler cannot longer handle an include in
<asm/cpufeature.h> which references boot_cpu_data which is
defined in <asm/processor.h>.
The only reason why <asm/msr.h> is included in <asm/processor.h> are the
set/get_debugctlmsr() inlines. They are defined there because <asm/processor.h>
is such a nice dump ground for everything. In fact they belong obviously
into <asm/debugreg.h>.
Move them to <asm/debugreg.h> and fix up the resulting damage which is just
exposing the reliance on random include chains.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20240304005104.454678686@linutronix.de
The __percpu annotation in struct amd_uncore is confusing Sparse:
uncore.c:649:10: sparse: warning: incorrect type in initializer (different address spaces)
uncore.c:649:10: sparse: expected void const [noderef] __percpu *__vpp_verify
uncore.c:649:10: sparse: got union amd_uncore_info *
The reason is that the __percpu annotation sits between the '*'
dereferencing operator and the member name.
Move it before the dereferencing operator to cure this.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20240304005104.394845326@linutronix.de
Now that __num_cores_per_package and __num_threads_per_package are
available, cpuinfo::x86_max_cores and the related math all over the place
can be replaced with the ready to consume data.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Link: https://lore.kernel.org/r/20240213210253.176147806@linutronix.de
AMD (ab)uses topology_die_id() to store the Node ID information and
topology_max_dies_per_pkg to store the number of nodes per package.
This collides with the proper processor die level enumeration which is
coming on AMD with CPUID 8000_0026, unless there is a correlation between
the two. There is zero documentation about that.
So provide new storage and new accessors which for now still access die_id
and topology_max_die_per_pkg(). Will be mopped up after AMD and HYGON are
converted over.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Wang Wendy <wendy.wang@intel.com>
Tested-by: K Prateek Nayak <kprateek.nayak@amd.com>
Link: https://lore.kernel.org/r/20240212153624.956116738@linutronix.de
- Add branch stack counters ABI extension to better capture
the growing amount of information the PMU exposes via
branch stack sampling. There's matching tooling support.
- Fix race when creating the nr_addr_filters sysfs file
- Add Intel Sierra Forest and Grand Ridge intel/cstate
PMU support.
- Add Intel Granite Rapids, Sierra Forest and Grand Ridge
uncore PMU support.
- Misc cleanups & fixes.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQJFBAABCgAvFiEEBpT5eoXrXCwVQwEKEnMQ0APhK1gFAmWb4lURHG1pbmdvQGtl
cm5lbC5vcmcACgkQEnMQ0APhK1jlnQ/+NSzrPQ9hEiS5a1iMMxdwC6IoXCmeFVsv
s5NsGaVC7FEgjm3oCfvQlP63HolMO9R7TNLZsgINzOda5IHtE7WUcgBK7gbZr+NT
WabdTyFrdmUr+Br0rLrEe0bxDSQU7r41ptqKE5HZRM9/3SbLhWgaXSJbfFAG2JV0
xboZ/2qzb7Puch6VTWv1YhuIpr1Pi817As4SOo7JR4V8jBB2bh2eZ7XBN1z23aw2
xuglbYml5gs4dOaFTqkRLWyn2PmrZ9wYKcdp63FVUscZ4LxvSw749BxEcNpTbxLp
PT6uXIKw9PnStNfscfrsk6fDocVJzqrOK71blgiOKbmhWTE0UimEpFf1Hd3ooewg
hFp3hmkE5Bc2MTUnwivkBxj96fz5rXH+3+Cue/5NsvDNlhlkswIIxzDw8M1G4rOI
KQMDUYFOhQPa3Hi1lSp2SgHI5AcYHudepr/Z3QMxD3iLs+Wo2cmDcp8d2VrMLfb7
GHSITG592iYcZPYsJosxby8CSFaUPxIl9l3AODQwWuEjd4PcOYa6iB2HbEa/mC3R
wXcs8mFIMAaH/HRYUlqUDA5pOqN5chb13iDtS4JqJqBKyWgdrDLCVxoZSQvB64+I
bldyy1e5oQSVVwJ42WLkUK3Eld2x75ki1JLZFwMgYuOgQv3jfu2VNenUWJ5ig0La
dPpHP8PwOoc=
=2O/5
-----END PGP SIGNATURE-----
Merge tag 'perf-core-2024-01-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull performance events updates from Ingo Molnar:
- Add branch stack counters ABI extension to better capture the growing
amount of information the PMU exposes via branch stack sampling.
There's matching tooling support.
- Fix race when creating the nr_addr_filters sysfs file
- Add Intel Sierra Forest and Grand Ridge intel/cstate PMU support
- Add Intel Granite Rapids, Sierra Forest and Grand Ridge uncore PMU
support
- Misc cleanups & fixes
* tag 'perf-core-2024-01-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Factor out topology_gidnid_map()
perf/x86/intel/uncore: Fix NULL pointer dereference issue in upi_fill_topology()
perf/x86/amd: Reject branch stack for IBS events
perf/x86/intel/uncore: Support Sierra Forest and Grand Ridge
perf/x86/intel/uncore: Support IIO free-running counters on GNR
perf/x86/intel/uncore: Support Granite Rapids
perf/x86/uncore: Use u64 to replace unsigned for the uncore offsets array
perf/x86/intel/uncore: Generic uncore_get_uncores and MMIO format of SPR
perf: Fix the nr_addr_filters fix
perf/x86/intel/cstate: Add Grand Ridge support
perf/x86/intel/cstate: Add Sierra Forest support
x86/smp: Export symbol cpu_clustergroup_mask()
perf/x86/intel/cstate: Cleanup duplicate attr_groups
perf/core: Fix narrow startup race when creating the perf nr_addr_filters sysfs file
perf/x86/intel: Support branch counters logging
perf/x86/intel: Reorganize attrs and is_visible
perf: Add branch_sample_call_stack
perf/x86: Add PERF_X86_EVENT_NEEDS_BRANCH_STACK flag
perf: Add branch stack counters
- A micro-optimization got misplaced as a cleanup:
- Micro-optimize the asm code in secondary_startup_64_no_verify()
- Change global variables to local
- Add missing kernel-doc function parameter descriptions
- Remove unused parameter from a macro
- Remove obsolete Kconfig entry
- Fix comments
- Fix typos, mostly scripted, manually reviewed
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=kUav
-----END PGP SIGNATURE-----
Merge tag 'x86-cleanups-2024-01-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cleanups from Ingo Molnar:
- Change global variables to local
- Add missing kernel-doc function parameter descriptions
- Remove unused parameter from a macro
- Remove obsolete Kconfig entry
- Fix comments
- Fix typos, mostly scripted, manually reviewed
and a micro-optimization got misplaced as a cleanup:
- Micro-optimize the asm code in secondary_startup_64_no_verify()
* tag 'x86-cleanups-2024-01-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
arch/x86: Fix typos
x86/head_64: Use TESTB instead of TESTL in secondary_startup_64_no_verify()
x86/docs: Remove reference to syscall trampoline in PTI
x86/Kconfig: Remove obsolete config X86_32_SMP
x86/io: Remove the unused 'bw' parameter from the BUILDIO() macro
x86/mtrr: Document missing function parameters in kernel-doc
x86/setup: Make relocated_ramdisk a local variable of relocate_initrd()
When commit c59a1f106f ("KVM: x86/pmu: Add IA32_PEBS_ENABLE
MSR emulation for extended PEBS") switched the initialization of
cpuc->guest_switch_msrs to use compound literals, it screwed up
the boolean logic:
+ u64 pebs_mask = cpuc->pebs_enabled & x86_pmu.pebs_capable;
...
- arr[0].guest = intel_ctrl & ~cpuc->intel_ctrl_host_mask;
- arr[0].guest &= ~(cpuc->pebs_enabled & x86_pmu.pebs_capable);
+ .guest = intel_ctrl & (~cpuc->intel_ctrl_host_mask | ~pebs_mask),
Before the patch, the value of arr[0].guest would have been intel_ctrl &
~cpuc->intel_ctrl_host_mask & ~pebs_mask. The intent is to always treat
PEBS events as host-only because, while the guest runs, there is no way
to tell the processor about the virtual address where to put PEBS records
intended for the host.
Unfortunately, the new expression can be expanded to
(intel_ctrl & ~cpuc->intel_ctrl_host_mask) | (intel_ctrl & ~pebs_mask)
which makes no sense; it includes any bit that isn't *both* marked as
exclude_guest and using PEBS. So, reinstate the old logic. Another
way to write it could be "intel_ctrl & ~(cpuc->intel_ctrl_host_mask |
pebs_mask)", presumably the intention of the author of the faulty.
However, I personally find the repeated application of A AND NOT B to
be a bit more readable.
This shows up as guest failures when running concurrent long-running
perf workloads on the host, and was reported to happen with rcutorture.
All guests on a given host would die simultaneously with something like an
instruction fault or a segmentation violation.
Reported-by: Paul E. McKenney <paulmck@kernel.org>
Analyzed-by: Sean Christopherson <seanjc@google.com>
Tested-by: Paul E. McKenney <paulmck@kernel.org>
Cc: stable@vger.kernel.org
Fixes: c59a1f106f ("KVM: x86/pmu: Add IA32_PEBS_ENABLE MSR emulation for extended PEBS")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The same code is used for retrieving package ID procedure from GIDNIDMAP
register. Factor out topology_gidnid_map() to avoid code duplication.
Signed-off-by: Alexander Antonov <alexander.antonov@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20231127185246.2371939-3-alexander.antonov@linux.intel.com
Get logical socket id instead of physical id in discover_upi_topology()
to avoid out-of-bound access on 'upi = &type->topology[nid][idx];' line
that leads to NULL pointer dereference in upi_fill_topology()
Fixes: f680b6e606 ("perf/x86/intel/uncore: Enable UPI topology discovery for Icelake Server")
Reported-by: Kyle Meyer <kyle.meyer@hpe.com>
Signed-off-by: Alexander Antonov <alexander.antonov@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Tested-by: Kyle Meyer <kyle.meyer@hpe.com>
Link: https://lore.kernel.org/r/20231127185246.2371939-2-alexander.antonov@linux.intel.com
The AMD IBS PMU doesn't handle branch stacks, so it should not accept
events with brstack.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20231130062246.290-1-ravi.bangoria@amd.com
The same as Granite Rapids, the Sierra Forest and Grand Ridge also
supports the discovery table feature and the same type of the uncore
units. The difference of the available units and counters can be
retrieved from the discovery table automatically.
Just add the CPU model ID.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Ammy Yi <ammy.yi@intel.com>
Link: https://lore.kernel.org/r/20231117163939.2468007-5-kan.liang@linux.intel.com
The free-running counters for IIO uncore blocks on Granite Rapids are
similar to Sapphire Rapids. The key difference is the offset of the
registers. The number of the IIO uncore blocks can also be retrieved
from the discovery table.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Ammy Yi <ammy.yi@intel.com>
Link: https://lore.kernel.org/r/20231117163939.2468007-4-kan.liang@linux.intel.com
The same as Sapphire Rapids, Granite Rapids also supports the discovery
table feature. All the basic uncore PMON information can be retrieved
from the discovery table which resides in the BIOS.
There are 4 new units are added on Granite Rapids, b2cmi, b2cxl, ubox,
and mdf_sbo. The layout of the counters is exactly the same as the
generic uncore counters. Only add a name for the new units. All the
details can be retrieved from the discovery table.
The description of the new units can be found at
https://www.intel.com/content/www/us/en/secure/content-details/772943/content-details.html
The other units, e.g., cha, iio, irp, pcu, and imc, are the same as
Sapphire Rapids.
Ignore the upi and b2upi units in the discovery table, which are broken
for now.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Ammy Yi <ammy.yi@intel.com>
Link: https://lore.kernel.org/r/20231117163939.2468007-3-kan.liang@linux.intel.com
The current perf doesn't save the complete address of an uncore unit.
The complete address of each unit is calculated by the base address +
offset. The type of the base address is u64, while the type of offset is
unsigned.
In the old platforms (without the discovery table method), the base
address and offset are hard coded in the driver. Perf can always use the
lowest address as the base address. Everything works well.
In the new platforms (starting from SPR), the discovery table provides
a complete address for all uncore units. To follow the current
framework/codes, when parsing the discovery table, the complete address
of the first box is stored as a base address. The offset of the
following units is calculated by the complete address of the unit minus
the base address (the address of the first unit). On GNR, the latter
units may have a lower address compared to the first unit. So the offset
is a negative value. The upper 32 bits are lost when casting a negative
u64 to an unsigned type.
Use u64 to replace unsigned for the uncore offsets array to correct the
above case. There is no functional change.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Ammy Yi <ammy.yi@intel.com>
Link: https://lore.kernel.org/r/20231117163939.2468007-2-kan.liang@linux.intel.com
Factor out SPR_UNCORE_MMIO_COMMON_FORMAT which can be reused by
Granite Rapids in the following patch.
Granite Rapids have more uncore units than Sapphire Rapids. Add new
parameters to support adjustable uncore units.
No functional change.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Ammy Yi <ammy.yi@intel.com>
Link: https://lore.kernel.org/r/20231117163939.2468007-1-kan.liang@linux.intel.com
When running perf-stat command on Intel hybrid platform, perf-stat
reports the following errors:
sudo taskset -c 7 ./perf stat -vvvv -e cpu_atom/instructions/ sleep 1
Opening: cpu/cycles/:HG
------------------------------------------------------------
perf_event_attr:
type 0 (PERF_TYPE_HARDWARE)
config 0xa00000000
disabled 1
------------------------------------------------------------
sys_perf_event_open: pid 0 cpu -1 group_fd -1 flags 0x8
sys_perf_event_open failed, error -16
Performance counter stats for 'sleep 1':
<not counted> cpu_atom/instructions/
It looks the cpu_atom/instructions/ event can't be enabled on atom PMU
even when the process is pinned on atom core. Investigation shows that
exclusive_event_init() helper always returns -EBUSY error in the perf
event creation. That's strange since the atom PMU should not be an
exclusive PMU.
Further investigation shows the issue was introduced by commit:
97588df87b ("perf/x86/intel: Add common intel_pmu_init_hybrid()")
The commit originally intents to clear the bit PERF_PMU_CAP_AUX_OUTPUT
from PMU capabilities if intel_cap.pebs_output_pt_available is not set,
but it incorrectly uses 'or' operation and leads to all PMU capabilities
bits are set to 1 except bit PERF_PMU_CAP_AUX_OUTPUT.
Testing this fix on Intel hybrid platforms, the observed issues
disappear.
Fixes: 97588df87b ("perf/x86/intel: Add common intel_pmu_init_hybrid()")
Signed-off-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231121014628.729989-1-dapeng1.mi@linux.intel.com
The same as the Sierra Forest, the Grand Ridge supports core C1/C6 and
module C6. But it doesn't support pkg C6 residency counter.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20231116142245.1233485-4-kan.liang@linux.intel.com
A new module C6 Residency Counter is introduced in the Sierra Forest.
The scope of the new counter is module (A cluster of cores shared L2
cache). Create a brand new cstate_module PMU to profile the new counter.
The only differences between the new cstate_module PMU and the existing
cstate PMU are the scope and events.
Regarding the choice of the new cstate_module PMU name, the current
naming rule of a cstate PMU is "cstate_" + the scope of the PMU. The
scope of the PMU is the cores shared L2. On SRF, Intel calls it
"module", while the internal Linux sched code calls it "cluster". The
"cstate_module" is used as the new PMU name, because
- The Cstate PMU driver is a Intel specific driver. It doesn't impact
other ARCHs. The name makes it consistent with the documentation.
- The "cluster" mainly be used by the scheduler developer, while the
user of cstate PMU is more likely a researcher reading HW docs and
optimizing power.
- In the Intel's SDM, the "cluster" has a different meaning/scope for
topology. Using it will mislead the end users.
Besides the module C6, the core C1/C6 and pkg C6 residency counters are
supported in the Sierra Forest as well.
Suggested-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20231116142245.1233485-3-kan.liang@linux.intel.com
The events of the cstate_core and cstate_pkg PMU have the same format.
They both need to create a "events" group (with empty attrs). The
attr_groups can be shared.
Remove the dedicated attr_groups for each cstate PMU. Use the shared
cstate_attr_groups to replace.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20231116142245.1233485-1-kan.liang@linux.intel.com
- Limit the hardcoded topology quirk for Hygon CPUs to those which have a
model ID less than 4. The newer models have the topology CPUID leaf 0xB
correctly implemented and are not affected.
- Make SMT control more robust against enumeration failures
SMT control was added to allow controlling SMT at boottime or
runtime. The primary purpose was to provide a simple mechanism to
disable SMT in the light of speculation attack vectors.
It turned out that the code is sensible to enumeration failures and
worked only by chance for XEN/PV. XEN/PV has no real APIC enumeration
which means the primary thread mask is not set up correctly. By chance
a XEN/PV boot ends up with smp_num_siblings == 2, which makes the
hotplug control stay at its default value "enabled". So the mask is
never evaluated.
The ongoing rework of the topology evaluation caused XEN/PV to end up
with smp_num_siblings == 1, which sets the SMT control to "not
supported" and the empty primary thread mask causes the hotplug core to
deny the bringup of the APS.
Make the decision logic more robust and take 'not supported' and 'not
implemented' into account for the decision whether a CPU should be
booted or not.
- Fake primary thread mask for XEN/PV
Pretend that all XEN/PV vCPUs are primary threads, which makes the
usage of the primary thread mask valid on XEN/PV. That is consistent
with because all of the topology information on XEN/PV is fake or even
non-existent.
- Encapsulate topology information in cpuinfo_x86
Move the randomly scattered topology data into a separate data
structure for readability and as a preparatory step for the topology
evaluation overhaul.
- Consolidate APIC ID data type to u32
It's fixed width hardware data and not randomly u16, int, unsigned long
or whatever developers decided to use.
- Cure the abuse of cpuinfo for persisting logical IDs.
Per CPU cpuinfo is used to persist the logical package and die
IDs. That's really not the right place simply because cpuinfo is
subject to be reinitialized when a CPU goes through an offline/online
cycle.
Use separate per CPU data for the persisting to enable the further
topology management rework. It will be removed once the new topology
management is in place.
- Provide a debug interface for inspecting topology information
Useful in general and extremly helpful for validating the topology
management rework in terms of correctness or "bug" compatibility.
-----BEGIN PGP SIGNATURE-----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=xrz8
-----END PGP SIGNATURE-----
Merge tag 'x86-core-2023-10-29-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 core updates from Thomas Gleixner:
- Limit the hardcoded topology quirk for Hygon CPUs to those which have
a model ID less than 4.
The newer models have the topology CPUID leaf 0xB correctly
implemented and are not affected.
- Make SMT control more robust against enumeration failures
SMT control was added to allow controlling SMT at boottime or
runtime. The primary purpose was to provide a simple mechanism to
disable SMT in the light of speculation attack vectors.
It turned out that the code is sensible to enumeration failures and
worked only by chance for XEN/PV. XEN/PV has no real APIC enumeration
which means the primary thread mask is not set up correctly. By
chance a XEN/PV boot ends up with smp_num_siblings == 2, which makes
the hotplug control stay at its default value "enabled". So the mask
is never evaluated.
The ongoing rework of the topology evaluation caused XEN/PV to end up
with smp_num_siblings == 1, which sets the SMT control to "not
supported" and the empty primary thread mask causes the hotplug core
to deny the bringup of the APS.
Make the decision logic more robust and take 'not supported' and 'not
implemented' into account for the decision whether a CPU should be
booted or not.
- Fake primary thread mask for XEN/PV
Pretend that all XEN/PV vCPUs are primary threads, which makes the
usage of the primary thread mask valid on XEN/PV. That is consistent
with because all of the topology information on XEN/PV is fake or
even non-existent.
- Encapsulate topology information in cpuinfo_x86
Move the randomly scattered topology data into a separate data
structure for readability and as a preparatory step for the topology
evaluation overhaul.
- Consolidate APIC ID data type to u32
It's fixed width hardware data and not randomly u16, int, unsigned
long or whatever developers decided to use.
- Cure the abuse of cpuinfo for persisting logical IDs.
Per CPU cpuinfo is used to persist the logical package and die IDs.
That's really not the right place simply because cpuinfo is subject
to be reinitialized when a CPU goes through an offline/online cycle.
Use separate per CPU data for the persisting to enable the further
topology management rework. It will be removed once the new topology
management is in place.
- Provide a debug interface for inspecting topology information
Useful in general and extremly helpful for validating the topology
management rework in terms of correctness or "bug" compatibility.
* tag 'x86-core-2023-10-29-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
x86/apic, x86/hyperv: Use u32 in hv_snp_boot_ap() too
x86/cpu: Provide debug interface
x86/cpu/topology: Cure the abuse of cpuinfo for persisting logical ids
x86/apic: Use u32 for wakeup_secondary_cpu[_64]()
x86/apic: Use u32 for [gs]et_apic_id()
x86/apic: Use u32 for phys_pkg_id()
x86/apic: Use u32 for cpu_present_to_apicid()
x86/apic: Use u32 for check_apicid_used()
x86/apic: Use u32 for APIC IDs in global data
x86/apic: Use BAD_APICID consistently
x86/cpu: Move cpu_l[l2]c_id into topology info
x86/cpu: Move logical package and die IDs into topology info
x86/cpu: Remove pointless evaluation of x86_coreid_bits
x86/cpu: Move cu_id into topology info
x86/cpu: Move cpu_core_id into topology info
hwmon: (fam15h_power) Use topology_core_id()
scsi: lpfc: Use topology_core_id()
x86/cpu: Move cpu_die_id into topology info
x86/cpu: Move phys_proc_id into topology info
x86/cpu: Encapsulate topology information in cpuinfo_x86
...
- Add AMD Unified Memory Controller (UMC) events introduced with Zen 4
- Simplify & clean up the uncore management code
- Fall back from RDPMC to RDMSR on certain uncore PMUs
- Improve per-package and cstate event reading
- Extend the Intel ref-cycles event to GP counters
- Fix Intel MTL event constraints
- Improve the Intel hybrid CPU handling code
- Micro-optimize the RAPL code
- Optimize perf_cgroup_switch()
- Improve large AUX area error handling
- Misc fixes and cleanups
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=OLsv
-----END PGP SIGNATURE-----
Merge tag 'perf-core-2023-10-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull performance event updates from Ingo Molnar:
- Add AMD Unified Memory Controller (UMC) events introduced with Zen 4
- Simplify & clean up the uncore management code
- Fall back from RDPMC to RDMSR on certain uncore PMUs
- Improve per-package and cstate event reading
- Extend the Intel ref-cycles event to GP counters
- Fix Intel MTL event constraints
- Improve the Intel hybrid CPU handling code
- Micro-optimize the RAPL code
- Optimize perf_cgroup_switch()
- Improve large AUX area error handling
- Misc fixes and cleanups
* tag 'perf-core-2023-10-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
perf/x86/amd/uncore: Pass through error code for initialization failures, instead of -ENODEV
perf/x86/amd/uncore: Fix uninitialized return value in amd_uncore_init()
x86/cpu: Fix the AMD Fam 17h, Fam 19h, Zen2 and Zen4 MSR enumerations
perf: Optimize perf_cgroup_switch()
perf/x86/amd/uncore: Add memory controller support
perf/x86/amd/uncore: Add group exclusivity
perf/x86/amd/uncore: Use rdmsr if rdpmc is unavailable
perf/x86/amd/uncore: Move discovery and registration
perf/x86/amd/uncore: Refactor uncore management
perf/core: Allow reading package events from perf_event_read_local
perf/x86/cstate: Allow reading the package statistics from local CPU
perf/x86/intel/pt: Fix kernel-doc comments
perf/x86/rapl: Annotate 'struct rapl_pmus' with __counted_by
perf/core: Rename perf_proc_update_handler() -> perf_event_max_sample_rate_handler(), for readability
perf/x86/rapl: Fix "Using plain integer as NULL pointer" Sparse warning
perf/x86/rapl: Use local64_try_cmpxchg in rapl_event_update()
perf/x86/rapl: Stop doing cpu_relax() in the local64_cmpxchg() loop in rapl_event_update()
perf/core: Bail out early if the request AUX area is out of bound
perf/x86/intel: Extend the ref-cycles event to GP counters
perf/x86/intel: Fix broken fixed event constraints extension
...
The branch counters logging (A.K.A LBR event logging) introduces a
per-counter indication of precise event occurrences in LBRs. It can
provide a means to attribute exposed retirement latency to combinations
of events across a block of instructions. It also provides a means of
attributing Timed LBR latencies to events.
The feature is first introduced on SRF/GRR. It is an enhancement of the
ARCH LBR. It adds new fields in the LBR_INFO MSRs to log the occurrences
of events on the GP counters. The information is displayed by the order
of counters.
The design proposed in this patch requires that the events which are
logged must be in a group with the event that has LBR. If there are
more than one LBR group, the counters logging information only from the
current group (overflowed) are stored for the perf tool, otherwise the
perf tool cannot know which and when other groups are scheduled
especially when multiplexing is triggered. The user can ensure it uses
the maximum number of counters that support LBR info (4 by now) by
making the group large enough.
The HW only logs events by the order of counters. The order may be
different from the order of enabling which the perf tool can understand.
When parsing the information of each branch entry, convert the counter
order to the enabled order, and store the enabled order in the extension
space.
Unconditionally reset LBRs for an LBR event group when it's deleted. The
logged counter information is only valid for the current LBR group. If
another LBR group is scheduled later, the information from the stale
LBRs would be otherwise wrongly interpreted.
Add a sanity check in intel_pmu_hw_config(). Disable the feature if other
counter filters (inv, cmask, edge, in_tx) are set or LBR call stack mode
is enabled. (For the LBR call stack mode, we cannot simply flush the
LBR, since it will break the call stack. Also, there is no obvious usage
with the call stack mode for now.)
Only applying the PERF_SAMPLE_BRANCH_COUNTERS doesn't require any branch
stack setup.
Expose the maximum number of supported counters and the width of the
counters into the sysfs. The perf tool can use the information to parse
the logged counters in each branch.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20231025201626.3000228-5-kan.liang@linux.intel.com
Some attrs and is_visible implementations are rather far away from one
another which makes the whole thing hard to interpret.
There are only two attribute groups which have both .attrs and
.is_visible, group_default and group_caps_lbr. Move them together.
No functional changes.
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20231025201626.3000228-4-kan.liang@linux.intel.com
Add a helper function to check call stack sample type.
The later patch will invoke the function in several places.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20231025201626.3000228-3-kan.liang@linux.intel.com
Currently, branch_sample_type !=0 is used to check whether a branch
stack setup is required. But it doesn't check the sample type,
unnecessary branch stack setup may be done for a counting event. E.g.,
perf record -e "{branch-instructions,branch-misses}:S" -j any
Also, the event only with the new PERF_SAMPLE_BRANCH_COUNTERS branch
sample type may not require a branch stack setup either.
Add a new flag NEEDS_BRANCH_STACK to indicate whether the event requires
a branch stack setup. Replace the needs_branch_stack() by checking the
new flag.
The counting event check is implemented here. The later patch will take
the new PERF_SAMPLE_BRANCH_COUNTERS into account.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20231025201626.3000228-2-kan.liang@linux.intel.com
Currently, the additional information of a branch entry is stored in a
u64 space. With more and more information added, the space is running
out. For example, the information of occurrences of events will be added
for each branch.
Two places were suggested to append the counters.
https://lore.kernel.org/lkml/20230802215814.GH231007@hirez.programming.kicks-ass.net/
One place is right after the flags of each branch entry. It changes the
existing struct perf_branch_entry. The later ARCH specific
implementation has to be really careful to consistently pick
the right struct.
The other place is right after the entire struct perf_branch_stack.
The disadvantage is that the pointer of the extra space has to be
recorded. The common interface perf_sample_save_brstack() has to be
updated.
The latter is much straightforward, and should be easily understood and
maintained. It is implemented in the patch.
Add a new branch sample type, PERF_SAMPLE_BRANCH_COUNTERS, to indicate
the event which is recorded in the branch info.
The "u64 counters" may store the occurrences of several events. The
information regarding the number of events/counters and the width of
each counter should be exposed via sysfs as a reference for the perf
tool. Define the branch_counter_nr and branch_counter_width ABI here.
The support will be implemented later in the Intel-specific patch.
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20231025201626.3000228-1-kan.liang@linux.intel.com
Pass through the appropriate error code when the registration of hotplug
callbacks fail during initialization, instead of returning a blanket -ENODEV.
[ mingo: Updated the changelog. ]
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20231016060743.332051-1-sandipan.das@amd.com
Some of the error paths in this function return don't initialize the
error code. Return -ENODEV by default.
Fixes: d6389d3ccc ("perf/x86/amd/uncore: Refactor uncore management")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/cec62eba-c4b8-4cb7-9671-58894dd4b974@moroto.mountain
The topology IDs which identify the LLC and L2 domains clearly belong to
the per CPU topology information.
Move them into cpuinfo_x86::cpuinfo_topo and get rid of the extra per CPU
data and the related exports.
This also paves the way to do proper topology evaluation during early boot
because it removes the only per CPU dependency for that.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230814085112.803864641@linutronix.de
Yet another topology related data pair. Rename logical_proc_id to
logical_pkg_id so it fits the common naming conventions.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230814085112.745139505@linutronix.de
Unified Memory Controller (UMC) events were introduced with Zen 4 as a
part of the Performance Monitoring Version 2 (PerfMonV2) enhancements.
An event is specified using the EventSelect bits and the RdWrMask bits
can be used for additional filtering of read and write requests.
As of now, a maximum of 12 channels of DDR5 are available on each socket
and each channel is controlled by a dedicated UMC. Each UMC, in turn,
has its own set of performance monitoring counters.
Since the MSR address space for the UMC PERF_CTL and PERF_CTR registers
are reused across sockets, uncore groups are created on the basis of
socket IDs. Hence, group exclusivity is mandatory while opening events
so that events for an UMC can only be opened on CPUs which are on the
same socket as the corresponding memory channel.
For each socket, the total number of available UMC counters and active
memory channels are determined from CPUID leaf 0x80000022 EBX and ECX
respectively. Usually, on Zen 4, each UMC has four counters.
MSR assignments are determined on the basis of active UMCs. E.g. if
UMCs 1, 4 and 9 are active for a given socket, then
* UMC 1 gets MSRs 0xc0010800 to 0xc0010807 as PERF_CTLs and PERF_CTRs
* UMC 4 gets MSRs 0xc0010808 to 0xc001080f as PERF_CTLs and PERF_CTRs
* UMC 9 gets MSRs 0xc0010810 to 0xc0010817 as PERF_CTLs and PERF_CTRs
If there are sockets without any online CPUs when the amd_uncore driver
is loaded, UMCs for such sockets will not be discoverable since the
mechanism relies on executing the CPUID instruction on an online CPU
from the socket.
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/b25f391205c22733493abec1ed850b71784edc5f.1696425185.git.sandipan.das@amd.com
In some cases, it may be necessary to restrict opening PMU events to a
subset of CPUs. E.g. Unified Memory Controller (UMC) PMUs are specific
to each active memory channel and the MSR address space for the PERF_CTL
and PERF_CTR registers is reused on each socket. Thus, opening events
for a specific UMC PMU should be restricted to CPUs belonging to the
same socket as that of the UMC. The "cpumask" of the PMU should also
reflect this accordingly.
Uncore PMUs which require this can use the new group attribute in struct
amd_uncore_pmu to set a valid group ID during the scan() phase. Later,
during init(), an uncore context for a CPU will be unavailable if the
group ID does not match.
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/937d6d71010a48ea4e069f4904b3116a5f99ecdf.1696425185.git.sandipan.das@amd.com
Uncore PMUs have traditionally been registered in the module init path.
This is fine for the existing DF and L3 PMUs since the CPUID information
does not vary across CPUs but not for the memory controller (UMC) PMUs
since information like active memory channels can vary for each socket
depending on how the DIMMs have been physically populated.
To overcome this, the discovery of PMU information using CPUID is moved
to the startup of UNCORE_STARTING. This cannot be done in the startup of
UNCORE_PREP since the hotplug callback does not run on the CPU that is
being brought online.
Previously, the startup of UNCORE_PREP was used for allocating uncore
contexts following which, the startup of UNCORE_STARTING was used to
find and reuse an existing sibling context, if possible. Any unused
contexts were added to a list for reclaimation later during the startup
of UNCORE_ONLINE.
Since all required CPUID info is now available only after the startup of
UNCORE_STARTING has completed, context allocation has been moved to the
startup of UNCORE_ONLINE. Before allocating contexts, the first CPU that
comes online has to take up the additional responsibility of registering
the PMUs. This is a one-time process though. Since sibling discovery now
happens prior to deciding whether a new context is required, there is no
longer a need to track and free up unused contexts.
The teardown of UNCORE_ONLINE and UNCORE_PREP functionally remain the
same.
Overall, the flow of control described above is achieved using the
following handlers for managing uncore PMUs. It is mandatory to define
them for each type of uncore PMU.
* scan() runs during startup of UNCORE_STARTING and collects PMU info
using CPUID.
* init() runs during startup of UNCORE_ONLINE, registers PMUs and sets
up uncore contexts.
* move() runs during teardown of UNCORE_ONLINE and migrates uncore
contexts to a shared sibling, if possible.
* free() runs during teardown of UNCORE_PREP and frees up uncore
contexts.
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/e6c447e48872fcab8452e0dd81b1c9cb09f39eb4.1696425185.git.sandipan.das@amd.com
Since struct amd_uncore is used to manage per-cpu contexts, rename it to
amd_uncore_ctx in order to better reflect its purpose. Add a new struct
amd_uncore_pmu to encapsulate all attributes which are shared by per-cpu
contexts for a corresponding PMU. These include the number of counters,
active mask, MSR and RDPMC base addresses, etc. Since the struct pmu is
now embedded, the corresponding amd_uncore_pmu for a given event can be
found by simply using container_of().
Finally, move all PMU-specific code to separate functions. While the
original event management functions continue to provide the base
functionality, all PMU-specific quirks and customizations are applied in
separate functions.
The motivation is to simplify the management of uncore PMUs.
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/24b38c49a5dae65d8c96e5d75a2b96ae97aaa651.1696425185.git.sandipan.das@amd.com
The MSR registers for reading the package residency counters are
available on every CPU of the package. To avoid doing unnecessary SMP
calls to read the values for these from the various CPUs inside a
package, allow reading them from any CPU of the package.
Suggested-by: Kan Liang <kan.liang@intel.com>
Signed-off-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20230912124432.3616761-2-tero.kristo@linux.intel.com
Some parameters or return codes were either wrong or missing,
update them.
Signed-off-by: Lucy Mielke <lucymielke@icloud.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/ZSOjQW3e2nJR4bAo@fedora.fritz.box
We found that a panic can occur when a vsyscall is made while LBR sampling
is active. If the vsyscall is interrupted (NMI) for perf sampling, this
call sequence can occur (most recent at top):
__insn_get_emulate_prefix()
insn_get_emulate_prefix()
insn_get_prefixes()
insn_get_opcode()
decode_branch_type()
get_branch_type()
intel_pmu_lbr_filter()
intel_pmu_handle_irq()
perf_event_nmi_handler()
Within __insn_get_emulate_prefix() at frame 0, a macro is called:
peek_nbyte_next(insn_byte_t, insn, i)
Within this macro, this dereference occurs:
(insn)->next_byte
Inspecting registers at this point, the value of the next_byte field is the
address of the vsyscall made, for example the location of the vsyscall
version of gettimeofday() at 0xffffffffff600000. The access to an address
in the vsyscall region will trigger an oops due to an unhandled page fault.
To fix the bug, filtering for vsyscalls can be done when
determining the branch type. This patch will return
a "none" branch if a kernel address if found to lie in the
vsyscall region.
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: JP Kobryn <inwardvessel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time via CONFIG_UBSAN_BOUNDS=y (for
array indexing) and CONFIG_FORTIFY_SOURCE=y (for strcpy/memcpy-family
functions).
Found with Coccinelle:
https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci [1]
Add __counted_by for 'struct rapl_pmus'.
No change in functionality intended.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20231006201754.work.473-kees@kernel.org
Change 0 to NULL when initializing the test field of perf_msr structs to
avoid the following sparse warnings:
make C=2 arch/x86/events/rapl.o
CHECK arch/x86/events/rapl.c
...
arch/x86/events/rapl.c:540:59: warning: Using plain integer as NULL pointer
arch/x86/events/rapl.c:542:59: warning: Using plain integer as NULL pointer
arch/x86/events/rapl.c:543:59: warning: Using plain integer as NULL pointer
arch/x86/events/rapl.c:544:59: warning: Using plain integer as NULL pointer
Signed-off-by: David Reaver <me@davidreaver.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230801155651.108076-1-me@davidreaver.com
Use local64_try_cmpxchg() instead of local64_cmpxchg(*ptr, old, new) == old.
X86 CMPXCHG instruction returns success in ZF flag, so this change saves a
compare after CMPXCHG (and related move instruction in front of CMPXCHG).
Also, try_cmpxchg() implicitly assigns old *ptr value to "old" when CMPXCHG
fails. There is no need to re-read the value in the loop.
No functional change intended.
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: https://lore.kernel.org/r/20230807145134.3176-2-ubizjak@gmail.com
According to the following commit:
f5fe24ef17 ("lockref: stop doing cpu_relax in the cmpxchg loop")
"On the x86-64 architecture even a failing cmpxchg grants exclusive
access to the cacheline, making it preferable to retry the failed op
immediately instead of stalling with the pause instruction."
Based on the above observation, remove cpu_relax() from the
local64_cmpxchg() loop of rapl_event_update().
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: https://lore.kernel.org/r/20230807145134.3176-1-ubizjak@gmail.com
Zen 4 systems running buggy microcode can hit a WARN_ON() in the PMI
handler, as shown below, several times while perf runs. A simple
`perf top` run is enough to render the system unusable:
WARNING: CPU: 18 PID: 20608 at arch/x86/events/amd/core.c:944 amd_pmu_v2_handle_irq+0x1be/0x2b0
This happens because the Performance Counter Global Status Register
(PerfCntGlobalStatus) has one or more bits set which are considered
reserved according to the "AMD64 Architecture Programmer’s Manual,
Volume 2: System Programming, 24593":
https://www.amd.com/system/files/TechDocs/24593.pdf
To make this less intrusive, warn just once if any reserved bit is set
and prompt the user to update the microcode. Also sanitize the value to
what the code is handling, so that the overflow events continue to be
handled for the number of counters that are known to be sane.
Going forward, the following microcode patch levels are recommended
for Zen 4 processors in order to avoid such issues with reserved bits:
Family=0x19 Model=0x11 Stepping=0x01: Patch=0x0a10113e
Family=0x19 Model=0x11 Stepping=0x02: Patch=0x0a10123e
Family=0x19 Model=0xa0 Stepping=0x01: Patch=0x0aa00116
Family=0x19 Model=0xa0 Stepping=0x02: Patch=0x0aa00212
Commit f2eb058afc57 ("linux-firmware: Update AMD cpu microcode") from
the linux-firmware tree has binaries that meet the minimum required
patch levels.
[ sandipan: - add message to prompt users to update microcode
- rework commit message and call out required microcode levels ]
Fixes: 7685665c39 ("perf/x86/amd/core: Add PerfMonV2 overflow handling")
Reported-by: Jirka Hladky <jhladky@redhat.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/all/3540f985652f41041e54ee82aa53e7dbd55739ae.1694696888.git.sandipan.das@amd.com/
Kernels older than v5.19 do not support PerfMonV2 and the PMI handler
does not clear the overflow bits of the PerfCntrGlobalStatus register.
Because of this, loading a recent kernel using kexec from an older
kernel can result in inconsistent register states on Zen 4 systems.
The PMI handler of the new kernel gets confused and shows a warning when
an overflow occurs because some of the overflow bits are set even if the
corresponding counters are inactive. These are remnants from overflows
that were handled by the older kernel.
During CPU hotplug, the PerfCntrGlobalCtl and PerfCntrGlobalStatus
registers should always be cleared for PerfMonV2-capable processors.
However, a condition used for NB event constaints applicable only to
older processors currently prevents this from happening. Move the reset
sequence to an appropriate place and also clear the LBR Freeze bit.
Fixes: 21d59e3e2c ("perf/x86/amd/core: Detect PerfMonV2 support")
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/882a87511af40792ba69bb0e9026f19a2e71e8a3.1694696888.git.sandipan.das@amd.com
The current ref-cycles event is only available on the fixed counter 2.
Starting from the GLC and GRT core, the architectural UnHalted Reference
Cycles event (0x013c) which is available on general-purpose counters
can collect the exact same events as the fixed counter 2.
Update the mapping of ref-cycles to 0x013c. So the ref-cycles can be
available on both fixed counter 2 and general-purpose counters.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230911144139.2354015-1-kan.liang@linux.intel.com
Unnecessary multiplexing is triggered when running an "instructions"
event on an MTL.
perf stat -e cpu_core/instructions/,cpu_core/instructions/ -a sleep 1
Performance counter stats for 'system wide':
115,489,000 cpu_core/instructions/ (50.02%)
127,433,777 cpu_core/instructions/ (49.98%)
1.002294504 seconds time elapsed
Linux architectural perf events, e.g., cycles and instructions, usually
have dedicated fixed counters. These events also have equivalent events
which can be used in the general-purpose counters. The counters are
precious. In the intel_pmu_check_event_constraints(), perf check/extend
the event constraints of these events. So these events can utilize both
fixed counters and general-purpose counters.
The following cleanup commit:
97588df87b ("perf/x86/intel: Add common intel_pmu_init_hybrid()")
forgot adding the intel_pmu_check_event_constraints() into update_pmu_cap().
The architectural perf events cannot utilize the general-purpose counters.
The code to check and update the counters, event constraints and
extra_regs is the same among hybrid systems. Move
intel_pmu_check_hybrid_pmus() to init_hybrid_pmu(), and
emove the duplicate check in update_pmu_cap().
Fixes: 97588df87b ("perf/x86/intel: Add common intel_pmu_init_hybrid()")
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230911135128.2322833-1-kan.liang@linux.intel.com
Starting from SPR, the basic uncore PMON information is retrieved from
the discovery table (resides in an MMIO space populated by BIOS). It is
called the discovery method. The existing value of the type->num_boxes
is from the discovery table.
On some SPR variants, there is a firmware bug that makes the value from the
discovery table incorrect. We use the value from the
SPR_MSR_UNC_CBO_CONFIG MSR to replace the one from the discovery table:
38776cc45e ("perf/x86/uncore: Correct the number of CHAs on SPR")
Unfortunately, the SPR_MSR_UNC_CBO_CONFIG isn't available for the EMR
XCC (Always returns 0), but the above firmware bug doesn't impact the
EMR XCC.
Don't let the value from the MSR replace the existing value from the
discovery table.
Fixes: 38776cc45e ("perf/x86/uncore: Correct the number of CHAs on SPR")
Reported-by: Stephane Eranian <eranian@google.com>
Reported-by: Yunying Sun <yunying.sun@intel.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Yunying Sun <yunying.sun@intel.com>
Link: https://lore.kernel.org/r/20230905134248.496114-1-kan.liang@linux.intel.com
The current hybrid initialization codes aren't well organized and are
hard to read.
Factor out intel_pmu_init_hybrid() to do a common setup for each
hybrid PMU. The PMU-specific capability will be updated later via either
hard code (ADL) or CPUID hybrid enumeration (MTL).
Splitting the ADL and MTL initialization codes, since they have
different uarches. The hard code PMU capabilities are not required for
MTL either. They can be enumerated by the new leaf 0x23 and
IA32_PERF_CAPABILITIES MSR.
The hybrid enumeration of the IA32_PERF_CAPABILITIES MSR is broken on
MTL. Using the default value.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230829125806.3016082-7-kan.liang@linux.intel.com
There is a fairly long list of grievances about the current code. The
main beefs:
1. hybrid_big_small assumes that the *HARDWARE* (CPUID) provided
core types are a bitmap. They are not. If Intel happened to
make a core type of 0xff, hilarity would ensue.
2. adl_get_hybrid_cpu_type() utterly inscrutable. There are
precisely zero comments and zero changelog about what it is
attempting to do.
According to Kan, the adl_get_hybrid_cpu_type() is there because some
Alder Lake (ADL) CPUs can do some silly things. Some ADL models are
*supposed* to be hybrid CPUs with big and little cores, but there are
some SKUs that only have big cores. CPUID(0x1a) on those CPUs does
not say that the CPUs are big cores. It apparently just returns 0x0.
It confuses perf because it expects to see either 0x40 (Core) or
0x20 (Atom).
The perf workaround for this is to watch for a CPU core saying it is
type 0x0. If that happens on an Alder Lake, it calls
x86_pmu.get_hybrid_cpu_type() and just assumes that the core is a
Core (0x40) CPU.
To fix up the mess, separate out the CPU types and the 'pmu' types.
This allows 'hybrid_pmu_type' bitmaps without worrying that some
future CPU type will set multiple bits.
Since the types are now separate, add a function to glue them back
together again. Actual comment on the situation in the glue
function (find_hybrid_pmu_for_cpu()).
Also, give ->get_hybrid_cpu_type() a real return type and make it
clear that it is overriding the *CPU* type, not the PMU type.
Rename cpu_type to pmu_type in the struct x86_hybrid_pmu to reflect the
change.
Originally-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230829125806.3016082-6-kan.liang@linux.intel.com
Use the intel_pmu_init_glc() and intel_pmu_init_grt() to replace the
duplicate code for ADL.
The current code already checks the PERF_X86_EVENT_TOPDOWN flag before
invoking the Topdown metrics functions. (The PERF_X86_EVENT_TOPDOWN flag
is to indicate the Topdown metric feature, which is only available for
the p-core.) Drop the unnecessary adl_set_topdown_event_period() and
adl_update_topdown_event().
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230829125806.3016082-5-kan.liang@linux.intel.com
From PMU's perspective, the ADL e-core and newer SRF/GRR have a similar
uarch. Most of the initialization code can be shared.
Factor out intel_pmu_init_grt() for the common initialization code.
The common part of the ADL e-core will be replaced by the later patch.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230829125806.3016082-4-kan.liang@linux.intel.com
The SPR and ADL p-core have a similar uarch. Most of the initialization
code can be shared.
Factor out intel_pmu_init_glc() for the common initialization code.
The common part of the ADL p-core will be replaced by the later patch.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230829125806.3016082-3-kan.liang@linux.intel.com
From PMU's perspective, the SPR/GNR server has a similar uarch to the
ADL/MTL client p-core. Many functions are shared. However, the shared
function name uses the abbreviation of the server product code name,
rather than the common uarch code name.
Rename these internal shared functions by the common uarch name.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230829125806.3016082-2-kan.liang@linux.intel.com
The Grand Ridge and Sierra Forest are successors to Snow Ridge. They
both have Crestmont core. From the core PMU's perspective, they are
similar to the e-core of MTL. The only difference is the LBR event
logging feature, which will be implemented in the following patches.
Create a non-hybrid PMU setup for Grand Ridge and Sierra Forest.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Link: https://lore.kernel.org/r/20230522113040.2329924-1-kan.liang@linux.intel.com
Alderlake N is an E-core only product using Gracemont
micro-architecture. It fits the pre-existing naming scheme perfectly
fine, adhere to it.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230807150405.686834933@infradead.org
Since commit bd27568117 ("perf: Rewrite core context handling") the
relationship between perf_event_context and PMUs has changed so that
the error scenario that PERF_PMU_CAP_HETEROGENEOUS_CPUS originally
silenced no longer exists.
Remove the capability to avoid confusion that it actually influences
any perf core behavior. This change should be a no-op.
Signed-off-by: James Clark <james.clark@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20230724134500.970496-3-james.clark@arm.com
Kernel IBS driver wasn't using new PERF_MEM_* APIs due to some of its
limitations. Mainly:
1. mem_lvl_num doesn't allow setting multiple sources whereas old API
allows it. Setting multiple data sources is useful because IBS on
pre-zen4 uarch doesn't provide fine granular DataSrc details (there
is only one such DataSrc(2h) though).
2. perf mem sorting logic (sort__lvl_cmp()) ignores mem_lvl_num. perf
c2c (c2c_decode_stats()) does not use mem_lvl_num at all.
1st one can be handled using ANY_CACHE with HOPS_0. 2nd is purely perf
tool specific issue and should be fixed separately.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230725150206.184-4-ravi.bangoria@amd.com
Use local64_try_cmpxchg instead of local64_cmpxchg (*ptr, old, new) == old.
x86 CMPXCHG instruction returns success in ZF flag, so this change saves a
compare after cmpxchg (and related move instruction in front of cmpxchg).
Also, try_cmpxchg implicitly assigns old *ptr value to "old" when cmpxchg
fails. There is no need to re-read the value in the loop.
No functional change intended.
Cc. "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20230706141720.2672-1-ubizjak@gmail.com
IBS PMUs can have only one event active at any point in time. Restrict
grouping of multiple IBS events.
Reported-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20230620091603.269-1-ravi.bangoria@amd.com
On SPR, the load latency event needs an auxiliary event in the same
group to work properly. There's a check in intel_pmu_hw_config()
for this to iterate sibling events and find a mem-loads-aux event.
The for_each_sibling_event() has a lockdep assert to make sure if it
disabled hardirq or hold leader->ctx->mutex. This works well if the
given event has a separate leader event since perf_try_init_event()
grabs the leader->ctx->mutex to protect the sibling list. But it can
cause a problem when the event itself is a leader since the event is
not initialized yet and there's no ctx for the event.
Actually I got a lockdep warning when I run the below command on SPR,
but I guess it could be a NULL pointer dereference.
$ perf record -d -e cpu/mem-loads/uP true
The code path to the warning is:
sys_perf_event_open()
perf_event_alloc()
perf_init_event()
perf_try_init_event()
x86_pmu_event_init()
hsw_hw_config()
intel_pmu_hw_config()
for_each_sibling_event()
lockdep_assert_event_ctx()
We don't need for_each_sibling_event() when it's a standalone event.
Let's return the error code directly.
Fixes: f3c0eba287 ("perf: Add a few assertions")
Reported-by: Greg Thelen <gthelen@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20230704181516.3293665-1-namhyung@kernel.org
- Rework & fix the event forwarding logic by extending the
core interface. This fixes AMD PMU events that have to
be forwarded from the core PMU to the IBS PMU.
- Add self-tests to test AMD IBS invocation via core PMU events
- Clean up Intel FixCntrCtl MSR encoding & handling
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=xn05
-----END PGP SIGNATURE-----
Merge tag 'perf-core-2023-06-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf events updates from Ingo Molnar:
- Rework & fix the event forwarding logic by extending the core
interface.
This fixes AMD PMU events that have to be forwarded from the
core PMU to the IBS PMU.
- Add self-tests to test AMD IBS invocation via core PMU events
- Clean up Intel FixCntrCtl MSR encoding & handling
* tag 'perf-core-2023-06-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Re-instate the linear PMU search
perf/x86/intel: Define bit macros for FixCntrCtl MSR
perf test: Add selftest to test IBS invocation via core pmu events
perf/core: Remove pmu linear searching code
perf/ibs: Fix interface via core pmu events
perf/core: Rework forwarding of {task|cpu}-clock events
When counting a FRONTEND event, the MSR_PEBS_FRONTEND is not correctly
set on GNR and MTL p-core.
The umask value for the FRONTEND events is changed on GNR and MTL. The
new umask is missing in the extra_regs[] table.
Add a dedicated intel_gnr_extra_regs[] for GNR and MTL p-core.
Fixes: bc4000fdb0 ("perf/x86/intel: Add Granite Rapids")
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20230615173242.3726364-1-kan.liang@linux.intel.com
The number of CHAs from the discovery table on some SPR variants is
incorrect, because of a firmware issue. An accurate number can be read
from the MSR UNC_CBO_CONFIG.
Fixes: 949b11381f ("perf/x86/intel/uncore: Add Sapphire Rapids server CHA support")
Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Stephane Eranian <eranian@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230508140206.283708-1-kan.liang@linux.intel.com
After commit b752ea0c28 ("perf/x86/intel/ds: Flush PEBS DS when changing
PEBS_DATA_CFG"), the cpuc->pebs_data_cfg may save some bits that are not
supported by real hardware, such as PEBS_UPDATE_DS_SW. This would cause
the VMX hardware MSR switching mechanism to save/restore invalid values
for PEBS_DATA_CFG MSR, thus crashing the host when PEBS is used for guest.
Fix it by using the active host value from cpuc->active_pebs_data_cfg.
Fixes: b752ea0c28 ("perf/x86/intel/ds: Flush PEBS DS when changing PEBS_DATA_CFG")
Signed-off-by: Like Xu <likexu@tencent.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20230517133808.67885-1-likexu@tencent.com
Define bit macros for FixCntrCtl MSR and replace the bit hardcoding
with these bit macros. This would make code be more human-readable.
Perf commands 'perf stat -e "instructions,cycles,ref-cycles"' and
'perf record -e "instructions,cycles,ref-cycles"' pass.
Signed-off-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20230504072128.3653470-1-dapeng1.mi@linux.intel.com
Although, IBS pmus can be invoked via their own interface, indirect
IBS invocation via core pmu events is also supported with fixed set
of events: cpu-cycles:p, r076:p (same as cpu-cycles:p) and r0C1:p
(micro-ops) for user convenience.
This indirect IBS invocation is broken since commit 66d258c5b0
("perf/core: Optimize perf_init_event()"), which added RAW pmu under
'pmu_idr' list and thus if event_init() fails with RAW pmu, it started
returning error instead of trying other pmus.
Forward precise events from core pmu to IBS by overwriting 'type' and
'config' in the kernel copy of perf_event_attr. Overwriting will cause
perf_init_event() to retry with updated 'type' and 'config', which will
automatically forward event to IBS pmu.
Without patch:
$ sudo ./perf record -C 0 -e r076:p -- sleep 1
Error:
The r076:p event is not supported.
With patch:
$ sudo ./perf record -C 0 -e r076:p -- sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.341 MB perf.data (37 samples) ]
Fixes: 66d258c5b0 ("perf/core: Optimize perf_init_event()")
Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20230504110003.2548-3-ravi.bangoria@amd.com
Several similar kernel warnings can be triggered,
[56605.607840] CPU0 PEBS record size 0, expected 32, config 0 cpuc->record_size=208
when the below commands are running in parallel for a while on SPR.
while true;
do
perf record --no-buildid -a --intr-regs=AX \
-e cpu/event=0xd0,umask=0x81/pp \
-c 10003 -o /dev/null ./triad;
done &
while true;
do
perf record -o /tmp/out -W -d \
-e '{ld_blocks.store_forward:period=1000000, \
MEM_TRANS_RETIRED.LOAD_LATENCY:u:precise=2:ldlat=4}' \
-c 1037 ./triad;
done
The triad program is just the generation of loads/stores.
The warnings are triggered when an unexpected PEBS record (with a
different config and size) is found.
A system-wide PEBS event with the large PEBS config may be enabled
during a context switch. Some PEBS records for the system-wide PEBS
may be generated while the old task is sched out but the new one
hasn't been sched in yet. When the new task is sched in, the
cpuc->pebs_record_size may be updated for the per-task PEBS events. So
the existing system-wide PEBS records have a different size from the
later PEBS records.
The PEBS buffer should be flushed right before the hardware is
reprogrammed. The new size and threshold should be updated after the
old buffer has been flushed.
Reported-by: Stephane Eranian <eranian@google.com>
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20230421184529.3320912-1-kan.liang@linux.intel.com
It missed to convert a PERF_SAMPLE_BRANCH_STACK user to call the new
perf_sample_save_brstack() helper in order to update the dyn_size.
This affects AMD Zen3 machines with the branch-brs event.
Fixes: eb55b455ef ("perf/core: Add perf_sample_save_brstack() helper")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20230427030527.580841-1-namhyung@kernel.org
Add missing clockticks and cas_count_* events for Intel SapphireRapids IMC
PMU. These events are useful to measure memory bandwidth.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20230419214241.2310385-1-eranian@google.com
Granite Rapids Xeon is successor or Emerald Rapids Xeon, and it will use
the same C-state residency counters as Emerald Rapids (and previous
Xeons, all the way back to Ice Lake Xeon).
Add Granite Rapids Xeon support.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230314170041.2967712-3-kan.liang@linux.intel.com
The same as Sapphire Rapids, the SMI_COUNT MSR is also supported on
Granite Rapids. Add Granite Rapids model.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230314170041.2967712-2-kan.liang@linux.intel.com
From core PMU's perspective, Granite Rapids is similar to the Sapphire
Rapids. The key differences include:
- Doesn't need the AUX event workaround for the mem load event.
(Implement in this patch).
- Support Retire Latency (Has been implemented in the commit
c87a31093c ("perf/x86: Support Retire Latency"))
- The event list, which will be supported in the perf tool later.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230314170041.2967712-1-kan.liang@linux.intel.com
The variable 'status' (which contains the unhandled overflow bits) is
not being properly masked in some cases, displaying the following
warning:
WARNING: CPU: 156 PID: 475601 at arch/x86/events/amd/core.c:972 amd_pmu_v2_handle_irq+0x216/0x270
This seems to be happening because the loop is being continued before
the status bit being unset, in case x86_perf_event_set_period()
returns 0. This is also causing an inconsistency because the "handled"
counter is incremented, but the status bit is not cleaned.
Move the bit cleaning together above, together when the "handled"
counter is incremented.
Fixes: 7685665c39 ("perf/x86/amd/core: Add PerfMonV2 overflow handling")
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Sandipan Das <sandipan.das@amd.com>
Link: https://lore.kernel.org/r/20230321113338.1669660-1-leitao@debian.org
- Provide a virtual cache topology to the guest to avoid
inconsistencies with migration on heterogenous systems. Non secure
software has no practical need to traverse the caches by set/way in
the first place.
- Add support for taking stage-2 access faults in parallel. This was an
accidental omission in the original parallel faults implementation,
but should provide a marginal improvement to machines w/o FEAT_HAFDBS
(such as hardware from the fruit company).
- A preamble to adding support for nested virtualization to KVM,
including vEL2 register state, rudimentary nested exception handling
and masking unsupported features for nested guests.
- Fixes to the PSCI relay that avoid an unexpected host SVE trap when
resuming a CPU when running pKVM.
- VGIC maintenance interrupt support for the AIC
- Improvements to the arch timer emulation, primarily aimed at reducing
the trap overhead of running nested.
- Add CONFIG_USERFAULTFD to the KVM selftests config fragment in the
interest of CI systems.
- Avoid VM-wide stop-the-world operations when a vCPU accesses its own
redistributor.
- Serialize when toggling CPACR_EL1.SMEN to avoid unexpected exceptions
in the host.
- Aesthetic and comment/kerneldoc fixes
- Drop the vestiges of the old Columbia mailing list and add [Oliver]
as co-maintainer
This also drags in arm64's 'for-next/sme2' branch, because both it and
the PSCI relay changes touch the EL2 initialization code.
RISC-V:
- Fix wrong usage of PGDIR_SIZE instead of PUD_SIZE
- Correctly place the guest in S-mode after redirecting a trap to the guest
- Redirect illegal instruction traps to guest
- SBI PMU support for guest
s390:
- Two patches sorting out confusion between virtual and physical
addresses, which currently are the same on s390.
- A new ioctl that performs cmpxchg on guest memory
- A few fixes
x86:
- Change tdp_mmu to a read-only parameter
- Separate TDP and shadow MMU page fault paths
- Enable Hyper-V invariant TSC control
- Fix a variety of APICv and AVIC bugs, some of them real-world,
some of them affecting architecurally legal but unlikely to
happen in practice
- Mark APIC timer as expired if its in one-shot mode and the count
underflows while the vCPU task was being migrated
- Advertise support for Intel's new fast REP string features
- Fix a double-shootdown issue in the emergency reboot code
- Ensure GIF=1 and disable SVM during an emergency reboot, i.e. give SVM
similar treatment to VMX
- Update Xen's TSC info CPUID sub-leaves as appropriate
- Add support for Hyper-V's extended hypercalls, where "support" at this
point is just forwarding the hypercalls to userspace
- Clean up the kvm->lock vs. kvm->srcu sequences when updating the PMU and
MSR filters
- One-off fixes and cleanups
- Fix and cleanup the range-based TLB flushing code, used when KVM is
running on Hyper-V
- Add support for filtering PMU events using a mask. If userspace
wants to restrict heavily what events the guest can use, it can now
do so without needing an absurd number of filter entries
- Clean up KVM's handling of "PMU MSRs to save", especially when vPMU
support is disabled
- Add PEBS support for Intel Sapphire Rapids
- Fix a mostly benign overflow bug in SEV's send|receive_update_data()
- Move several SVM-specific flags into vcpu_svm
x86 Intel:
- Handle NMI VM-Exits before leaving the noinstr region
- A few trivial cleanups in the VM-Enter flows
- Stop enabling VMFUNC for L1 purely to document that KVM doesn't support
EPTP switching (or any other VM function) for L1
- Fix a crash when using eVMCS's enlighted MSR bitmaps
Generic:
- Clean up the hardware enable and initialization flow, which was
scattered around multiple arch-specific hooks. Instead, just
let the arch code call into generic code. Both x86 and ARM should
benefit from not having to fight common KVM code's notion of how
to do initialization.
- Account allocations in generic kvm_arch_alloc_vm()
- Fix a memory leak if coalesced MMIO unregistration fails
selftests:
- On x86, cache the CPU vendor (AMD vs. Intel) and use the info to emit
the correct hypercall instruction instead of relying on KVM to patch
in VMMCALL
- Use TAP interface for kvm_binary_stats_test and tsc_msrs_test
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmP2YA0UHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroPg/Qf+J6nT+TkIa+8Ei+fN1oMTDp4YuIOx
mXvJ9mRK9sQ+tAUVwvDz3qN/fK5mjsYbRHIDlVc5p2Q3bCrVGDDqXPFfCcLx1u+O
9U9xjkO4JxD2LS9pc70FYOyzVNeJ8VMGOBbC2b0lkdYZ4KnUc6e/WWFKJs96bK+H
duo+RIVyaMthnvbTwSv1K3qQb61n6lSJXplywS8KWFK6NZAmBiEFDAWGRYQE9lLs
VcVcG0iDJNL/BQJ5InKCcvXVGskcCm9erDszPo7w4Bypa4S9AMS42DHUaRZrBJwV
/WqdH7ckIz7+OSV0W1j+bKTHAFVTCjXYOM7wQykgjawjICzMSnnG9Gpskw==
=goe1
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"ARM:
- Provide a virtual cache topology to the guest to avoid
inconsistencies with migration on heterogenous systems. Non secure
software has no practical need to traverse the caches by set/way in
the first place
- Add support for taking stage-2 access faults in parallel. This was
an accidental omission in the original parallel faults
implementation, but should provide a marginal improvement to
machines w/o FEAT_HAFDBS (such as hardware from the fruit company)
- A preamble to adding support for nested virtualization to KVM,
including vEL2 register state, rudimentary nested exception
handling and masking unsupported features for nested guests
- Fixes to the PSCI relay that avoid an unexpected host SVE trap when
resuming a CPU when running pKVM
- VGIC maintenance interrupt support for the AIC
- Improvements to the arch timer emulation, primarily aimed at
reducing the trap overhead of running nested
- Add CONFIG_USERFAULTFD to the KVM selftests config fragment in the
interest of CI systems
- Avoid VM-wide stop-the-world operations when a vCPU accesses its
own redistributor
- Serialize when toggling CPACR_EL1.SMEN to avoid unexpected
exceptions in the host
- Aesthetic and comment/kerneldoc fixes
- Drop the vestiges of the old Columbia mailing list and add [Oliver]
as co-maintainer
RISC-V:
- Fix wrong usage of PGDIR_SIZE instead of PUD_SIZE
- Correctly place the guest in S-mode after redirecting a trap to the
guest
- Redirect illegal instruction traps to guest
- SBI PMU support for guest
s390:
- Sort out confusion between virtual and physical addresses, which
currently are the same on s390
- A new ioctl that performs cmpxchg on guest memory
- A few fixes
x86:
- Change tdp_mmu to a read-only parameter
- Separate TDP and shadow MMU page fault paths
- Enable Hyper-V invariant TSC control
- Fix a variety of APICv and AVIC bugs, some of them real-world, some
of them affecting architecurally legal but unlikely to happen in
practice
- Mark APIC timer as expired if its in one-shot mode and the count
underflows while the vCPU task was being migrated
- Advertise support for Intel's new fast REP string features
- Fix a double-shootdown issue in the emergency reboot code
- Ensure GIF=1 and disable SVM during an emergency reboot, i.e. give
SVM similar treatment to VMX
- Update Xen's TSC info CPUID sub-leaves as appropriate
- Add support for Hyper-V's extended hypercalls, where "support" at
this point is just forwarding the hypercalls to userspace
- Clean up the kvm->lock vs. kvm->srcu sequences when updating the
PMU and MSR filters
- One-off fixes and cleanups
- Fix and cleanup the range-based TLB flushing code, used when KVM is
running on Hyper-V
- Add support for filtering PMU events using a mask. If userspace
wants to restrict heavily what events the guest can use, it can now
do so without needing an absurd number of filter entries
- Clean up KVM's handling of "PMU MSRs to save", especially when vPMU
support is disabled
- Add PEBS support for Intel Sapphire Rapids
- Fix a mostly benign overflow bug in SEV's
send|receive_update_data()
- Move several SVM-specific flags into vcpu_svm
x86 Intel:
- Handle NMI VM-Exits before leaving the noinstr region
- A few trivial cleanups in the VM-Enter flows
- Stop enabling VMFUNC for L1 purely to document that KVM doesn't
support EPTP switching (or any other VM function) for L1
- Fix a crash when using eVMCS's enlighted MSR bitmaps
Generic:
- Clean up the hardware enable and initialization flow, which was
scattered around multiple arch-specific hooks. Instead, just let
the arch code call into generic code. Both x86 and ARM should
benefit from not having to fight common KVM code's notion of how to
do initialization
- Account allocations in generic kvm_arch_alloc_vm()
- Fix a memory leak if coalesced MMIO unregistration fails
selftests:
- On x86, cache the CPU vendor (AMD vs. Intel) and use the info to
emit the correct hypercall instruction instead of relying on KVM to
patch in VMMCALL
- Use TAP interface for kvm_binary_stats_test and tsc_msrs_test"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (325 commits)
KVM: SVM: hyper-v: placate modpost section mismatch error
KVM: x86/mmu: Make tdp_mmu_allowed static
KVM: arm64: nv: Use reg_to_encoding() to get sysreg ID
KVM: arm64: nv: Only toggle cache for virtual EL2 when SCTLR_EL2 changes
KVM: arm64: nv: Filter out unsupported features from ID regs
KVM: arm64: nv: Emulate EL12 register accesses from the virtual EL2
KVM: arm64: nv: Allow a sysreg to be hidden from userspace only
KVM: arm64: nv: Emulate PSTATE.M for a guest hypervisor
KVM: arm64: nv: Add accessors for SPSR_EL1, ELR_EL1 and VBAR_EL1 from virtual EL2
KVM: arm64: nv: Handle SMCs taken from virtual EL2
KVM: arm64: nv: Handle trapped ERET from virtual EL2
KVM: arm64: nv: Inject HVC exceptions to the virtual EL2
KVM: arm64: nv: Support virtual EL2 exceptions
KVM: arm64: nv: Handle HCR_EL2.NV system register traps
KVM: arm64: nv: Add nested virt VCPU primitives for vEL2 VCPU state
KVM: arm64: nv: Add EL2 system registers to vcpu context
KVM: arm64: nv: Allow userspace to set PSR_MODE_EL2x
KVM: arm64: nv: Reset VCPU to EL2 registers if VCPU nested virt is set
KVM: arm64: nv: Introduce nested virtualization VCPU feature
KVM: arm64: Use the S2 MMU context to iterate over S2 table
...
- Improve the scalability of the CFS bandwidth unthrottling logic
with large number of CPUs.
- Fix & rework various cpuidle routines, simplify interaction with
the generic scheduler code. Add __cpuidle methods as noinstr to
objtool's noinstr detection and fix boatloads of cpuidle bugs & quirks.
- Add new ABI: introduce MEMBARRIER_CMD_GET_REGISTRATIONS,
to query previously issued registrations.
- Limit scheduler slice duration to the sysctl_sched_latency period,
to improve scheduling granularity with a large number of SCHED_IDLE
tasks.
- Debuggability enhancement on sys_exit(): warn about disabled IRQs,
but also enable them to prevent a cascade of followup problems and
repeat warnings.
- Fix the rescheduling logic in prio_changed_dl().
- Micro-optimize cpufreq and sched-util methods.
- Micro-optimize ttwu_runnable()
- Micro-optimize the idle-scanning in update_numa_stats(),
select_idle_capacity() and steal_cookie_task().
- Update the RSEQ code & self-tests
- Constify various scheduler methods
- Remove unused methods
- Refine __init tags
- Documentation updates
- ... Misc other cleanups, fixes
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=l1nN
-----END PGP SIGNATURE-----
Merge tag 'sched-core-2023-02-20' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
- Improve the scalability of the CFS bandwidth unthrottling logic with
large number of CPUs.
- Fix & rework various cpuidle routines, simplify interaction with the
generic scheduler code. Add __cpuidle methods as noinstr to objtool's
noinstr detection and fix boatloads of cpuidle bugs & quirks.
- Add new ABI: introduce MEMBARRIER_CMD_GET_REGISTRATIONS, to query
previously issued registrations.
- Limit scheduler slice duration to the sysctl_sched_latency period, to
improve scheduling granularity with a large number of SCHED_IDLE
tasks.
- Debuggability enhancement on sys_exit(): warn about disabled IRQs,
but also enable them to prevent a cascade of followup problems and
repeat warnings.
- Fix the rescheduling logic in prio_changed_dl().
- Micro-optimize cpufreq and sched-util methods.
- Micro-optimize ttwu_runnable()
- Micro-optimize the idle-scanning in update_numa_stats(),
select_idle_capacity() and steal_cookie_task().
- Update the RSEQ code & self-tests
- Constify various scheduler methods
- Remove unused methods
- Refine __init tags
- Documentation updates
- Misc other cleanups, fixes
* tag 'sched-core-2023-02-20' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (110 commits)
sched/rt: pick_next_rt_entity(): check list_entry
sched/deadline: Add more reschedule cases to prio_changed_dl()
sched/fair: sanitize vruntime of entity being placed
sched/fair: Remove capacity inversion detection
sched/fair: unlink misfit task from cpu overutilized
objtool: mem*() are not uaccess safe
cpuidle: Fix poll_idle() noinstr annotation
sched/clock: Make local_clock() noinstr
sched/clock/x86: Mark sched_clock() noinstr
x86/pvclock: Improve atomic update of last_value in pvclock_clocksource_read()
x86/atomics: Always inline arch_atomic64*()
cpuidle: tracing, preempt: Squash _rcuidle tracing
cpuidle: tracing: Warn about !rcu_is_watching()
cpuidle: lib/bug: Disable rcu_is_watching() during WARN/BUG
cpuidle: drivers: firmware: psci: Dont instrument suspend code
KVM: selftests: Fix build of rseq test
exit: Detect and fix irq disabled state in oops
cpuidle, arm64: Fix the ARM64 cpuidle logic
cpuidle: mvebu: Fix duplicate flags assignment
sched/fair: Limit sched slice duration
...
- Optimize perf_sample_data layout
- Prepare sample data handling for BPF integration
- Update the x86 PMU driver for Intel Meteor Lake
- Restructure the x86 uncore code to fix a SPR (Sapphire Rapids)
discovery breakage
- Fix the x86 Zhaoxin PMU driver
- Cleanups
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=ztUT
-----END PGP SIGNATURE-----
Merge tag 'perf-core-2023-02-20' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Ingo Molnar:
- Optimize perf_sample_data layout
- Prepare sample data handling for BPF integration
- Update the x86 PMU driver for Intel Meteor Lake
- Restructure the x86 uncore code to fix a SPR (Sapphire Rapids)
discovery breakage
- Fix the x86 Zhaoxin PMU driver
- Cleanups
* tag 'perf-core-2023-02-20' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
perf/x86/intel/uncore: Add Meteor Lake support
x86/perf/zhaoxin: Add stepping check for ZXC
perf/x86/intel/ds: Fix the conversion from TSC to perf time
perf/x86/uncore: Don't WARN_ON_ONCE() for a broken discovery table
perf/x86/uncore: Add a quirk for UPI on SPR
perf/x86/uncore: Ignore broken units in discovery table
perf/x86/uncore: Fix potential NULL pointer in uncore_get_alias_name
perf/x86/uncore: Factor out uncore_device_to_die()
perf/core: Call perf_prepare_sample() before running BPF
perf/core: Introduce perf_prepare_header()
perf/core: Do not pass header for sample ID init
perf/core: Set data->sample_flags in perf_prepare_sample()
perf/core: Add perf_sample_save_brstack() helper
perf/core: Add perf_sample_save_raw_data() helper
perf/core: Add perf_sample_save_callchain() helper
perf/core: Save the dynamic parts of sample data size
x86/kprobes: Use switch-case for 0xFF opcodes in prepare_emulation
perf/core: Change the layout of perf_sample_data
perf/x86/msr: Add Meteor Lake support
perf/x86/cstate: Add Meteor Lake support
...
Now that KVM disables vPMU support on hybrid CPUs, WARN and return zeros
if perf_get_x86_pmu_capability() is invoked on a hybrid CPU. The helper
doesn't provide an accurate accounting of the PMU capabilities for hybrid
CPUs and needs to be enhanced if KVM, or anything else outside of perf,
wants to act on the PMU capabilities.
Cc: stable@vger.kernel.org
Cc: Andrew Cooper <Andrew.Cooper3@citrix.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Link: https://lore.kernel.org/all/20220818181530.2355034-1-kan.liang@linux.intel.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20230208204230.1360502-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The uncore subsystem for Meteor Lake is similar to the previous Alder
Lake. The main difference is that MTL provides PMU support for different
tiles, while ADL only provides PMU support for the whole package. On
ADL, there are CBOX, ARB, and clockbox uncore PMON units. On MTL, they
are split into CBOX/HAC_CBOX, ARB/HAC_ARB, and cncu/sncu which provides
a fixed counter for clockticks. Also, new MSR addresses are introduced
on MTL.
The IMC uncore PMON is the same as Alder Lake. Add new PCIIDs of IMC for
Meteor Lake.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230210190238.1726237-1-kan.liang@linux.intel.com
Some of Nano series processors will lead GP when accessing
PMC fixed counter. Meanwhile, their hardware support for PMC
has not announced externally. So exclude Nano CPUs from ZXC
by checking stepping information. This is an unambiguous way
to differentiate between ZXC and Nano CPUs.
Following are Nano and ZXC FMS information:
Nano FMS: Family=6, Model=F, Stepping=[0-A][C-D]
ZXC FMS: Family=6, Model=F, Stepping=E-F OR
Family=6, Model=0x19, Stepping=0-3
Fixes: 3a4ac121c2 ("x86/perf: Add hardware performance events support for Zhaoxin CPU.")
Reported-by: Arjan <8vvbbqzo567a@nospam.xutrox.com>
Reported-by: Kevin Brace <kevinbrace@gmx.com>
Signed-off-by: silviazhao <silviazhao-oc@zhaoxin.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=212389
The time order is incorrect when the TSC in a PEBS record is used.
$perf record -e cycles:upp dd if=/dev/zero of=/dev/null
count=10000
$ perf script --show-task-events
perf-exec 0 0.000000: PERF_RECORD_COMM: perf-exec:915/915
dd 915 106.479872: PERF_RECORD_COMM exec: dd:915/915
dd 915 106.483270: PERF_RECORD_EXIT(915:915):(914:914)
dd 915 106.512429: 1 cycles:upp:
ffffffff96c011b7 [unknown] ([unknown])
... ...
The perf time is from sched_clock_cpu(). The current PEBS code
unconditionally convert the TSC to native_sched_clock(). There is a
shift between the two clocks. If the TSC is stable, the shift is
consistent, __sched_clock_offset. If the TSC is unstable, the shift has
to be calculated at runtime.
This patch doesn't support the conversion when the TSC is unstable. The
TSC unstable case is a corner case and very unlikely to happen. If it
happens, the TSC in a PEBS record will be dropped and fall back to
perf_event_clock().
Fixes: 47a3aeb39e ("perf/x86/intel/pebs: Fix PEBS timestamps overwritten")
Reported-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/CAM9d7cgWDVAq8-11RbJ2uGfwkKD6fA-OMwOKDrNUrU_=8MgEjg@mail.gmail.com/
According to Intel SDM, the EPT-friendly PEBS is supported by all the
platforms after ICX, ADL and the future platforms with PEBS format 5.
Currently the only in-kernel user of this capability is KVM, which has
very limited support for hybrid core pmu, so ADL and its successors do
not currently expose this capability. When both hybrid core and PEBS
format 5 are present, KVM will decide on its own merits.
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-perf-users@vger.kernel.org
Suggested-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Like Xu <likexu@tencent.com>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20221109082802.27543-4-likexu@tencent.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmPW7E8eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGf7MIAI0JnHN9WvtEukSZ
E6j6+cEGWxsvD6q0g3GPolaKOCw7hlv0pWcFJFcUAt0jebspMdxV2oUGJ8RYW7Lg
nCcHvEVswGKLAQtQSWw52qotW6fUfMPsNYYB5l31sm1sKH4Cgss0W7l2HxO/1LvG
TSeNHX53vNAZ8pVnFYEWCSXC9bzrmU/VALF2EV00cdICmfvjlgkELGXoLKJJWzUp
s63fBHYGGURSgwIWOKStoO6HNo0j/F/wcSMx8leY8qDUtVKHj4v24EvSgxUSDBER
ch3LiSQ6qf4sw/z7pqruKFthKOrlNmcc0phjiES0xwwGiNhLv0z3rAhc4OM2cgYh
SDc/Y/c=
=zpaD
-----END PGP SIGNATURE-----
Merge tag 'v6.2-rc6' into sched/core, to pick up fixes
Pick up fixes before merging another batch of cpuidle updates.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The kernel warning message is triggered, when SPR MCC is used.
[ 17.945331] ------------[ cut here ]------------
[ 17.946305] WARNING: CPU: 65 PID: 1 at
arch/x86/events/intel/uncore_discovery.c:184
intel_uncore_has_discovery_tables+0x4c0/0x65c
[ 17.946305] Modules linked in:
[ 17.946305] CPU: 65 PID: 1 Comm: swapper/0 Not tainted
5.4.17-2136.313.1-X10-2c+ #4
It's caused by the broken discovery table of UPI.
The discovery tables are from hardware. Except for dropping the broken
information, there is nothing Linux can do. Using WARN_ON_ONCE() is
overkilled.
Use the pr_info() to replace WARN_ON_ONCE(), and specify what uncore unit
is dropped and the reason.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Michael Petlan <mpetlan@redhat.com>
Link: https://lore.kernel.org/r/20230112200105.733466-6-kan.liang@linux.intel.com
The discovery table of UPI on some SPR variants, e.g., MCC, is broken.
The third UPI table may includes a wrong address which points to a
non-exists device. The bug impacts both UPI and M3UPI uncore PMON.
Use a pre-defined UPI and M3UPI table to replace the broken table.
Different BIOS may populate a device into a different domain or a
different BUS. The accurate location can only be retrieved at load time.
Add spr_update_device_location() to update the location of the UPI and
M3UPI in the pre-defined table.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Michael Petlan <mpetlan@redhat.com>
Link: https://lore.kernel.org/r/20230112200105.733466-5-kan.liang@linux.intel.com
Some units in a discovery table may be broken, e.g., UPI of SPR MCC.
A generic method is required to ignore the broken units.
Add uncore_units_ignore in the struct intel_uncore_init_fun, which
indicates the type ID of broken units. It will be assigned by the
platform-specific code later when the platform has a broken discovery
table.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Michael Petlan <mpetlan@redhat.com>
Link: https://lore.kernel.org/r/20230112200105.733466-4-kan.liang@linux.intel.com
The current code assumes that the discovery table provides valid
box_ids for the normal units. It's not the case anymore since some units
in the discovery table are broken on some SPR variants.
Factor out uncore_get_box_id(). Check the existence of the type->box_ids
before using it. If it's not available, use pmu_idx.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Michael Petlan <mpetlan@redhat.com>
Link: https://lore.kernel.org/r/20230112200105.733466-3-kan.liang@linux.intel.com
The same code is used to retrieve the logical die ID with a given PCI
device in both the discovery code and the code that supports a system
with > 8 nodes.
Factor out uncore_device_to_die() to replace the duplicate code.
No functional change.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Michael Petlan <mpetlan@redhat.com>
Link: https://lore.kernel.org/r/20230112200105.733466-2-kan.liang@linux.intel.com
From the perspective of Intel cstate residency counters,
Emerald Rapids is the same as the Sapphire Rapids and Ice Lake.
Add Emerald Rapids model.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230106160449.3566477-2-kan.liang@linux.intel.com
From core PMU's perspective, Emerald Rapids is the same as the Sapphire
Rapids. The only difference is the event list, which will be
supported in the perf tool later.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230106160449.3566477-1-kan.liang@linux.intel.com
Factor out perf_prepare_header() so that it can call
perf_prepare_sample() without a header if not needed.
Also it checks the filtered_sample_type to avoid duplicate
work when perf_prepare_sample() is called twice (or more).
Suggested-by: Peter Zijlstr <peterz@infradead.org>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Song Liu <song@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230118060559.615653-8-namhyung@kernel.org
When we saves the branch stack to the perf sample data, we needs to
update the sample flags and the dynamic size. To make sure this is
done consistently, add the perf_sample_save_brstack() helper and
convert all call sites.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230118060559.615653-5-namhyung@kernel.org
When we save the raw_data to the perf sample data, we need to update
the sample flags and the dynamic size. To make sure this is done
consistently, add the perf_sample_save_raw_data() helper and convert
all call sites.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230118060559.615653-4-namhyung@kernel.org
When we save the callchain to the perf sample data, we need to update
the sample flags and the dynamic size. To ensure this is done consistently,
add the perf_sample_save_callchain() helper and convert all call sites.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Song Liu <song@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230118060559.615653-3-namhyung@kernel.org
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmPEGkMeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGE4YH/1sxdve3nlWT7eyf
VDanaCZFc2u6Sk1td23HyhvOVbFjj1E39UokHK9YfzD4hhn+u9SFvDgoXHGhHzYq
IhDvNM3mLsKpEtjwNbbi/lt6tryJchhZ96O5leRiUxZaw/GBVnHrKGR56vCjC/DB
zq8td4I+TmTPMpsL3e3WZqJoX3bjTqgZFNShA1mZFYtuQRpAVkJkafMRwuAySIMQ
+FyK/zZ+MpGJ7y/UmWfaBmS5GtjBz0fva7fTbEkUqk8bDtNUWMBhsTKtgU1LBpBe
Yrkhs3sdQdpKSm9yNaNrlLhSjFwkusV5kR09p6/5w+wthdPmjnoUZuEnAZpYyydE
ZY7+Vqk=
=q9Ac
-----END PGP SIGNATURE-----
Merge tag 'v6.2-rc4' into perf/core, to pick up fixes
Move from the -rc1 base to the fresher -rc4 kernel that
has various fixes included, before applying a larger
patchset.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The perf_lopwr_cb() function is called from the idle routines; there
is no RCU there, we must not enter tracing.
Use __always_inline, noidle annotations and existing no-trace methods.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20230112195539.392862891@infradead.org
Meteor Lake is Intel's successor to Raptor lake. PPERF and SMI_COUNT MSRs
are also supported.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230104201349.1451191-7-kan.liang@linux.intel.com
Meteor Lake is Intel's successor to Raptor lake. From the perspective of
Intel cstate residency counters, there is nothing changed compared with
Raptor lake.
Share adl_cstates with Raptor lake.
Update the comments for Meteor Lake.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230104201349.1451191-6-kan.liang@linux.intel.com
The new CPUID leaf 0x23 reports the "true view" of PMU resources.
The sub-leaf 1 reports the available general-purpose counters and fixed
counters. Update the number of counters and fixed counters when the
sub-leaf is detected.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230104201349.1451191-5-kan.liang@linux.intel.com
Retire Latency reports the number of elapsed core clocks between the
retirement of the instruction indicated by the Instruction Pointer field
of the PEBS record and the retirement of the prior instruction. It's
enumerated by the IA32_PERF_CAPABILITIES.PEBS_TIMING_INFO[17].
Add flag PMU_FL_RETIRE_LATENCY to indicate the availability of the
feature.
The Retire Latency is not supported by the fixed counter 0 on p-core of
MTL.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230104201349.1451191-3-kan.liang@linux.intel.com
From PMU's perspective, Meteor Lake is similar to Alder Lake. Both are
hybrid platforms, with e-core and p-core.
The key differences include:
- The e-core supports 2 PDIST GP counters (GP0 & GP1)
- New MSRs for the Module Snoop Response Events on the e-core.
- New Data Source fields are introduced for the e-core.
- There are 8 GP counters for the e-core.
- The load latency AUX event is not required for the p-core anymore.
- Retire Latency (Support in a separate patch) for both cores.
Since most of the code in the intel_pmu_init() should be the same as
Alder Lake, to avoid code duplication, share the path with Alder Lake.
Add new specific functions of extra_regs, and get_event_constraints
to support the OCR events, Module Snoop Response Events and 2 PDIST
GP counters on e-core.
Add new MTL specific mem_attrs which drops the load latency AUX event.
The Data Source field is extended to 4:0, which can contains max 32
sources.
The Retire Latency is implemented with a separate patch.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230104201349.1451191-2-kan.liang@linux.intel.com
From the perspective of the uncore PMU, the new Emerald Rapids is the
same as the Sapphire Rapids. The only difference is the event list,
which will be supported in the perf tool later.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230106160449.3566477-4-kan.liang@linux.intel.com
Meteor Lake is Intel's successor to Raptor lake. PPERF and SMI_COUNT MSRs
are also supported.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Link: https://lore.kernel.org/r/20230104201349.1451191-7-kan.liang@linux.intel.com
Meteor Lake is Intel's successor to Raptor lake. From the perspective of
Intel cstate residency counters, there is nothing changed compared with
Raptor lake.
Share adl_cstates with Raptor lake.
Update the comments for Meteor Lake.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Link: https://lore.kernel.org/r/20230104201349.1451191-6-kan.liang@linux.intel.com
Since Tigerlake seems to have inherited its cstates and other RAPL power
caps from Icelake, assume it also follows Icelake for its RAPL events.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20221228113454.1199118-1-rodrigo.vivi@intel.com
The x86_pmu.lbr_info is 0 unless explicitly initialized, so there's
no point checking x86_pmu.intel_cap.lbr_format.
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Signed-off-by: Yang Weijiang <weijiang.yang@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Link: https://lkml.kernel.org/r/20221125040604.5051-2-weijiang.yang@intel.com
The left shift of int 32 bit integer constant 1 is evaluated using 32 bit
arithmetic and then passed as a 64 bit function argument. In the case where
i is 32 or more this can lead to an overflow. Avoid this by shifting
using the BIT_ULL macro instead.
Fixes: 471af006a7 ("perf/x86/amd: Constrain Large Increment per Cycle events")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Ian Rogers <irogers@google.com>
Acked-by: Kim Phillips <kim.phillips@amd.com>
Link: https://lore.kernel.org/r/20221202135149.1797974-1-colin.i.king@gmail.com
* Enable the per-vcpu dirty-ring tracking mechanism, together with an
option to keep the good old dirty log around for pages that are
dirtied by something other than a vcpu.
* Switch to the relaxed parallel fault handling, using RCU to delay
page table reclaim and giving better performance under load.
* Relax the MTE ABI, allowing a VMM to use the MAP_SHARED mapping option,
which multi-process VMMs such as crosvm rely on (see merge commit 382b5b87a9:
"Fix a number of issues with MTE, such as races on the tags being
initialised vs the PG_mte_tagged flag as well as the lack of support
for VM_SHARED when KVM is involved. Patches from Catalin Marinas and
Peter Collingbourne").
* Merge the pKVM shadow vcpu state tracking that allows the hypervisor
to have its own view of a vcpu, keeping that state private.
* Add support for the PMUv3p5 architecture revision, bringing support
for 64bit counters on systems that support it, and fix the
no-quite-compliant CHAIN-ed counter support for the machines that
actually exist out there.
* Fix a handful of minor issues around 52bit VA/PA support (64kB pages
only) as a prefix of the oncoming support for 4kB and 16kB pages.
* Pick a small set of documentation and spelling fixes, because no
good merge window would be complete without those.
s390:
* Second batch of the lazy destroy patches
* First batch of KVM changes for kernel virtual != physical address support
* Removal of a unused function
x86:
* Allow compiling out SMM support
* Cleanup and documentation of SMM state save area format
* Preserve interrupt shadow in SMM state save area
* Respond to generic signals during slow page faults
* Fixes and optimizations for the non-executable huge page errata fix.
* Reprogram all performance counters on PMU filter change
* Cleanups to Hyper-V emulation and tests
* Process Hyper-V TLB flushes from a nested guest (i.e. from a L2 guest
running on top of a L1 Hyper-V hypervisor)
* Advertise several new Intel features
* x86 Xen-for-KVM:
** Allow the Xen runstate information to cross a page boundary
** Allow XEN_RUNSTATE_UPDATE flag behaviour to be configured
** Add support for 32-bit guests in SCHEDOP_poll
* Notable x86 fixes and cleanups:
** One-off fixes for various emulation flows (SGX, VMXON, NRIPS=0).
** Reinstate IBPB on emulated VM-Exit that was incorrectly dropped a few
years back when eliminating unnecessary barriers when switching between
vmcs01 and vmcs02.
** Clean up vmread_error_trampoline() to make it more obvious that params
must be passed on the stack, even for x86-64.
** Let userspace set all supported bits in MSR_IA32_FEAT_CTL irrespective
of the current guest CPUID.
** Fudge around a race with TSC refinement that results in KVM incorrectly
thinking a guest needs TSC scaling when running on a CPU with a
constant TSC, but no hardware-enumerated TSC frequency.
** Advertise (on AMD) that the SMM_CTL MSR is not supported
** Remove unnecessary exports
Generic:
* Support for responding to signals during page faults; introduces
new FOLL_INTERRUPTIBLE flag that was reviewed by mm folks
Selftests:
* Fix an inverted check in the access tracking perf test, and restore
support for asserting that there aren't too many idle pages when
running on bare metal.
* Fix build errors that occur in certain setups (unsure exactly what is
unique about the problematic setup) due to glibc overriding
static_assert() to a variant that requires a custom message.
* Introduce actual atomics for clear/set_bit() in selftests
* Add support for pinning vCPUs in dirty_log_perf_test.
* Rename the so called "perf_util" framework to "memstress".
* Add a lightweight psuedo RNG for guest use, and use it to randomize
the access pattern and write vs. read percentage in the memstress tests.
* Add a common ucall implementation; code dedup and pre-work for running
SEV (and beyond) guests in selftests.
* Provide a common constructor and arch hook, which will eventually be
used by x86 to automatically select the right hypercall (AMD vs. Intel).
* A bunch of added/enabled/fixed selftests for ARM64, covering memslots,
breakpoints, stage-2 faults and access tracking.
* x86-specific selftest changes:
** Clean up x86's page table management.
** Clean up and enhance the "smaller maxphyaddr" test, and add a related
test to cover generic emulation failure.
** Clean up the nEPT support checks.
** Add X86_PROPERTY_* framework to retrieve multi-bit CPUID values.
** Fix an ordering issue in the AMX test introduced by recent conversions
to use kvm_cpu_has(), and harden the code to guard against similar bugs
in the future. Anything that tiggers caching of KVM's supported CPUID,
kvm_cpu_has() in this case, effectively hides opt-in XSAVE features if
the caching occurs before the test opts in via prctl().
Documentation:
* Remove deleted ioctls from documentation
* Clean up the docs for the x86 MSR filter.
* Various fixes
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmOaFrcUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroPemQgAq49excg2Cc+EsHnZw3vu/QWdA0Rt
KhL3OgKxuHNjCbD2O9n2t5di7eJOTQ7F7T0eDm3xPTr4FS8LQ2327/mQePU/H2CF
mWOpq9RBWLzFsSTeVA2Mz9TUTkYSnDHYuRsBvHyw/n9cL76BWVzjImldFtjYjjex
yAwl8c5itKH6bc7KO+5ydswbvBzODkeYKUSBNdbn6m0JGQST7XppNwIAJvpiHsii
Qgpk0e4Xx9q4PXG/r5DedI6BlufBsLhv0aE9SHPzyKH3JbbUFhJYI8ZD5OhBQuYW
MwxK2KlM5Jm5ud2NZDDlsMmmvd1lnYCFDyqNozaKEWC1Y5rq1AbMa51fXA==
=QAYX
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"ARM64:
- Enable the per-vcpu dirty-ring tracking mechanism, together with an
option to keep the good old dirty log around for pages that are
dirtied by something other than a vcpu.
- Switch to the relaxed parallel fault handling, using RCU to delay
page table reclaim and giving better performance under load.
- Relax the MTE ABI, allowing a VMM to use the MAP_SHARED mapping
option, which multi-process VMMs such as crosvm rely on (see merge
commit 382b5b87a9: "Fix a number of issues with MTE, such as
races on the tags being initialised vs the PG_mte_tagged flag as
well as the lack of support for VM_SHARED when KVM is involved.
Patches from Catalin Marinas and Peter Collingbourne").
- Merge the pKVM shadow vcpu state tracking that allows the
hypervisor to have its own view of a vcpu, keeping that state
private.
- Add support for the PMUv3p5 architecture revision, bringing support
for 64bit counters on systems that support it, and fix the
no-quite-compliant CHAIN-ed counter support for the machines that
actually exist out there.
- Fix a handful of minor issues around 52bit VA/PA support (64kB
pages only) as a prefix of the oncoming support for 4kB and 16kB
pages.
- Pick a small set of documentation and spelling fixes, because no
good merge window would be complete without those.
s390:
- Second batch of the lazy destroy patches
- First batch of KVM changes for kernel virtual != physical address
support
- Removal of a unused function
x86:
- Allow compiling out SMM support
- Cleanup and documentation of SMM state save area format
- Preserve interrupt shadow in SMM state save area
- Respond to generic signals during slow page faults
- Fixes and optimizations for the non-executable huge page errata
fix.
- Reprogram all performance counters on PMU filter change
- Cleanups to Hyper-V emulation and tests
- Process Hyper-V TLB flushes from a nested guest (i.e. from a L2
guest running on top of a L1 Hyper-V hypervisor)
- Advertise several new Intel features
- x86 Xen-for-KVM:
- Allow the Xen runstate information to cross a page boundary
- Allow XEN_RUNSTATE_UPDATE flag behaviour to be configured
- Add support for 32-bit guests in SCHEDOP_poll
- Notable x86 fixes and cleanups:
- One-off fixes for various emulation flows (SGX, VMXON, NRIPS=0).
- Reinstate IBPB on emulated VM-Exit that was incorrectly dropped
a few years back when eliminating unnecessary barriers when
switching between vmcs01 and vmcs02.
- Clean up vmread_error_trampoline() to make it more obvious that
params must be passed on the stack, even for x86-64.
- Let userspace set all supported bits in MSR_IA32_FEAT_CTL
irrespective of the current guest CPUID.
- Fudge around a race with TSC refinement that results in KVM
incorrectly thinking a guest needs TSC scaling when running on a
CPU with a constant TSC, but no hardware-enumerated TSC
frequency.
- Advertise (on AMD) that the SMM_CTL MSR is not supported
- Remove unnecessary exports
Generic:
- Support for responding to signals during page faults; introduces
new FOLL_INTERRUPTIBLE flag that was reviewed by mm folks
Selftests:
- Fix an inverted check in the access tracking perf test, and restore
support for asserting that there aren't too many idle pages when
running on bare metal.
- Fix build errors that occur in certain setups (unsure exactly what
is unique about the problematic setup) due to glibc overriding
static_assert() to a variant that requires a custom message.
- Introduce actual atomics for clear/set_bit() in selftests
- Add support for pinning vCPUs in dirty_log_perf_test.
- Rename the so called "perf_util" framework to "memstress".
- Add a lightweight psuedo RNG for guest use, and use it to randomize
the access pattern and write vs. read percentage in the memstress
tests.
- Add a common ucall implementation; code dedup and pre-work for
running SEV (and beyond) guests in selftests.
- Provide a common constructor and arch hook, which will eventually
be used by x86 to automatically select the right hypercall (AMD vs.
Intel).
- A bunch of added/enabled/fixed selftests for ARM64, covering
memslots, breakpoints, stage-2 faults and access tracking.
- x86-specific selftest changes:
- Clean up x86's page table management.
- Clean up and enhance the "smaller maxphyaddr" test, and add a
related test to cover generic emulation failure.
- Clean up the nEPT support checks.
- Add X86_PROPERTY_* framework to retrieve multi-bit CPUID values.
- Fix an ordering issue in the AMX test introduced by recent
conversions to use kvm_cpu_has(), and harden the code to guard
against similar bugs in the future. Anything that tiggers
caching of KVM's supported CPUID, kvm_cpu_has() in this case,
effectively hides opt-in XSAVE features if the caching occurs
before the test opts in via prctl().
Documentation:
- Remove deleted ioctls from documentation
- Clean up the docs for the x86 MSR filter.
- Various fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (361 commits)
KVM: x86: Add proper ReST tables for userspace MSR exits/flags
KVM: selftests: Allocate ucall pool from MEM_REGION_DATA
KVM: arm64: selftests: Align VA space allocator with TTBR0
KVM: arm64: Fix benign bug with incorrect use of VA_BITS
KVM: arm64: PMU: Fix period computation for 64bit counters with 32bit overflow
KVM: x86: Advertise that the SMM_CTL MSR is not supported
KVM: x86: remove unnecessary exports
KVM: selftests: Fix spelling mistake "probabalistic" -> "probabilistic"
tools: KVM: selftests: Convert clear/set_bit() to actual atomics
tools: Drop "atomic_" prefix from atomic test_and_set_bit()
tools: Drop conflicting non-atomic test_and_{clear,set}_bit() helpers
KVM: selftests: Use non-atomic clear/set bit helpers in KVM tests
perf tools: Use dedicated non-atomic clear/set bit helpers
tools: Take @bit as an "unsigned long" in {clear,set}_bit() helpers
KVM: arm64: selftests: Enable single-step without a "full" ucall()
KVM: x86: fix APICv/x2AVIC disabled when vm reboot by itself
KVM: Remove stale comment about KVM_REQ_UNHALT
KVM: Add missing arch for KVM_CREATE_DEVICE and KVM_{SET,GET}_DEVICE_ATTR
KVM: Reference to kvm_userspace_memory_region in doc and comments
KVM: Delete all references to removed KVM_SET_MEMORY_ALIAS ioctl
...
- Thoroughly rewrite the data structures that implement perf task context handling,
with the goal of fixing various quirks and unfeatures both in already merged,
and in upcoming proposed code.
The old data structure is the per task and per cpu perf_event_contexts:
task_struct::perf_events_ctxp[] <-> perf_event_context <-> perf_cpu_context
^ | ^ | ^
`---------------------------------' | `--> pmu ---'
v ^
perf_event ------'
In this new design this is replaced with a single task context and
a single CPU context, plus intermediate data-structures:
task_struct::perf_event_ctxp -> perf_event_context <- perf_cpu_context
^ | ^ ^
`---------------------------' | |
| | perf_cpu_pmu_context <--.
| `----. ^ |
| | | |
| v v |
| ,--> perf_event_pmu_context |
| | |
| | |
v v |
perf_event ---> pmu ----------------'
[ See commit bd27568117 for more details. ]
This rewrite was developed by Peter Zijlstra and Ravi Bangoria.
- Optimize perf_tp_event()
- Update the Intel uncore PMU driver, extending it with UPI topology discovery
on various hardware models.
- Misc fixes & cleanups
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=KNaI
-----END PGP SIGNATURE-----
Merge tag 'perf-core-2022-12-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf events updates from Ingo Molnar:
- Thoroughly rewrite the data structures that implement perf task
context handling, with the goal of fixing various quirks and
unfeatures both in already merged, and in upcoming proposed code.
The old data structure is the per task and per cpu
perf_event_contexts:
task_struct::perf_events_ctxp[] <-> perf_event_context <-> perf_cpu_context
^ | ^ | ^
`---------------------------------' | `--> pmu ---'
v ^
perf_event ------'
In this new design this is replaced with a single task context and a
single CPU context, plus intermediate data-structures:
task_struct::perf_event_ctxp -> perf_event_context <- perf_cpu_context
^ | ^ ^
`---------------------------' | |
| | perf_cpu_pmu_context <--.
| `----. ^ |
| | | |
| v v |
| ,--> perf_event_pmu_context |
| | |
| | |
v v |
perf_event ---> pmu ----------------'
[ See commit bd27568117 for more details. ]
This rewrite was developed by Peter Zijlstra and Ravi Bangoria.
- Optimize perf_tp_event()
- Update the Intel uncore PMU driver, extending it with UPI topology
discovery on various hardware models.
- Misc fixes & cleanups
* tag 'perf-core-2022-12-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
perf/x86/intel/uncore: Fix reference count leak in __uncore_imc_init_box()
perf/x86/intel/uncore: Fix reference count leak in snr_uncore_mmio_map()
perf/x86/intel/uncore: Fix reference count leak in hswep_has_limit_sbox()
perf/x86/intel/uncore: Fix reference count leak in sad_cfg_iio_topology()
perf/x86/intel/uncore: Make set_mapping() procedure void
perf/x86/intel/uncore: Update sysfs-devices-mapping file
perf/x86/intel/uncore: Enable UPI topology discovery for Sapphire Rapids
perf/x86/intel/uncore: Enable UPI topology discovery for Icelake Server
perf/x86/intel/uncore: Get UPI NodeID and GroupID
perf/x86/intel/uncore: Enable UPI topology discovery for Skylake Server
perf/x86/intel/uncore: Generalize get_topology() for SKX PMUs
perf/x86/intel/uncore: Disable I/O stacks to PMU mapping on ICX-D
perf/x86/intel/uncore: Clear attr_update properly
perf/x86/intel/uncore: Introduce UPI topology type
perf/x86/intel/uncore: Generalize IIO topology support
perf/core: Don't allow grouping events from different hw pmus
perf/amd/ibs: Make IBS a core pmu
perf: Fix function pointer case
perf/x86/amd: Remove the repeated declaration
perf: Fix possible memleak in pmu_dev_alloc()
...
-----BEGIN PGP SIGNATURE-----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=CxjR
-----END PGP SIGNATURE-----
Merge tag 'unsigned-char-6.2-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/zx2c4/linux
Pull unsigned-char conversion from Jason Donenfeld:
"Enable -funsigned-char and fix code affected by that flag.
During the 6.1 cycle, several patches already made it into the tree,
which were for code that was already broken on at least one
architecture, where the naked char had a different sign than the code
author anticipated, or were part of some bug fix for an existing bug
that this initiative unearthed.
These 6.1-era fixes are:
648060902a ("MIPS: pic32: treat port as signed integer")
5c26159c97 ("ipvs: use explicitly signed chars")
e6cb876945 ("wifi: airo: do not assign -1 to unsigned char")
937ec9f7d5 ("staging: rtl8192e: remove bogus ssid character sign test")
6770473832 ("misc: sgi-gru: use explicitly signed char")
50895a55bc ("ALSA: rme9652: use explicitly signed char")
ee03c0f200 ("ALSA: au88x0: use explicitly signed char")
835bed1b83 ("fbdev: sisfb: use explicitly signed char")
50f19697dd ("parisc: Use signed char for hardware path in pdc.h")
66063033f7 ("wifi: rt2x00: use explicitly signed or unsigned types")
Regarding patches in this pull:
- There is one patch in this pull that should have made it to you
during 6.1 ("media: stv0288: use explicitly signed char"), but the
maintainer was MIA during the cycle, so it's in here instead.
- Two patches fix single architecture code affected by unsigned char
("perf/x86: Make struct p4_event_bind::cntr signed array" and
"sparc: sbus: treat CPU index as integer"), while one patch fixes
an unused typedef, in case it's ever used in the future ("media:
atomisp: make hive_int8 explictly signed").
- Finally, there's the change to actually enable -funsigned-char
("kbuild: treat char as always unsigned") and then the removal of
some no longer useful !__CHAR_UNSIGNED__ selftest code ("lib:
assume char is unsigned").
The various fixes were found with a combination of diffing objdump
output, a large variety of Coccinelle scripts, and plain old grep. In
the end, things didn't seem as bad as I feared they would. But of
course, it's also possible I missed things.
However, this has been in linux-next for basically an entire cycle
now, so I'm not overly worried. I've also been daily driving this on
my laptop for all of 6.1. Still, this series, and the ones sent for
6.1 don't total in quantity to what I thought it'd be, so I will be on
the lookout for breakage.
We could receive a few reports that are quickly fixable. Hopefully we
won't receive a barrage of reports that would result in a revert. And
just maybe we won't receive any reports at all and nobody will even
notice. Knock on wood"
* tag 'unsigned-char-6.2-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/zx2c4/linux:
lib: assume char is unsigned
kbuild: treat char as always unsigned
media: atomisp: make hive_int8 explictly signed
media: stv0288: use explicitly signed char
sparc: sbus: treat CPU index as integer
perf/x86: Make struct p4_event_bind::cntr signed array
pci_get_device() will increase the reference count for the returned
pci_dev, so tgl_uncore_get_mc_dev() will return a pci_dev with its
reference count increased. We need to call pci_dev_put() to decrease the
reference count before exiting from __uncore_imc_init_box(). Add
pci_dev_put() for both normal and error path.
Fixes: fdb6482244 ("perf/x86: Add Intel Tiger Lake uncore support")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20221118063137.121512-5-wangxiongfeng2@huawei.com
pci_get_device() will increase the reference count for the returned
pci_dev, so snr_uncore_get_mc_dev() will return a pci_dev with its
reference count increased. We need to call pci_dev_put() to decrease the
reference count. Let's add the missing pci_dev_put().
Fixes: ee49532b38 ("perf/x86/intel/uncore: Add IMC uncore support for Snow Ridge")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20221118063137.121512-4-wangxiongfeng2@huawei.com
pci_get_device() will increase the reference count for the returned
'dev'. We need to call pci_dev_put() to decrease the reference count.
Since 'dev' is only used in pci_read_config_dword(), let's add
pci_dev_put() right after it.
Fixes: 9d480158ee ("perf/x86/intel/uncore: Remove uncore extra PCI dev HSWEP_PCI_PCU_3")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20221118063137.121512-3-wangxiongfeng2@huawei.com
pci_get_device() will increase the reference count for the returned
pci_dev, and also decrease the reference count for the input parameter
*from* if it is not NULL.
If we break the loop in sad_cfg_iio_topology() with 'dev' not NULL. We
need to call pci_dev_put() to decrease the reference count. Since
pci_dev_put() can handle the NULL input parameter, we can just add one
pci_dev_put() right before 'return ret'.
Fixes: c1777be364 ("perf/x86/intel/uncore: Enable I/O stacks to IIO PMON mapping on SNR")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20221118063137.121512-2-wangxiongfeng2@huawei.com
Return value of set_mapping() is not needed to be checked anymore.
So, make this procedure void.
Signed-off-by: Alexander Antonov <alexander.antonov@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20221117122833.3103580-12-alexander.antonov@linux.intel.com
UPI topology discovery on SPR is same as in ICX but UBOX device has
different Device ID 0x3250.
This patch enables /sys/devices/uncore_upi_*/die* attributes on SPR.
Signed-off-by: Alexander Antonov <alexander.antonov@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20221117122833.3103580-10-alexander.antonov@linux.intel.com
UPI topology discovery relies on data from KTILP0 (offset 0x94) and
KTIPCSTS (offset 0x120) as well as on SKX but on Icelake Server these
registers reside under UBOX (Device ID 0x3450) bus.
This patch enables /sys/devices/uncore_upi_*/die* attributes on Icelake
Server.
Signed-off-by: Alexander Antonov <alexander.antonov@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20221117122833.3103580-9-alexander.antonov@linux.intel.com
The GIDNIDMAP register of UBOX device is used to get the topology
information in the snbep_pci2phy_map_init(). The same approach will be
used to discover UPI topology for ICX and SPR platforms.
Move common code that will be reused in next patches.
Signed-off-by: Alexander Antonov <alexander.antonov@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20221117122833.3103580-8-alexander.antonov@linux.intel.com
UPI topology discovery relies on data from KTILP0 (offset 0x94) and
KTIPCSTS (offset 0x120) registers which reside under IIO bus(3) on
SKX/CLX.
This patch enable UPI topology discovery on Skylake Server. Topology is
exposed through attributes /sys/devices/uncore_upi_<pmu_idx>/dieX,
where dieX is file which holds "upi_<idx1>:die_<idx2>" connected to
this UPI link.
Signed-off-by: Alexander Antonov <alexander.antonov@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20221117122833.3103580-7-alexander.antonov@linux.intel.com
Factor out a generic code from skx_iio_get_topology() to skx_pmu_get_topology()
to avoid code duplication. This code will be used by get_topology() procedure
for SKX UPI PMUs in the further patch.
Signed-off-by: Alexander Antonov <alexander.antonov@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20221117122833.3103580-6-alexander.antonov@linux.intel.com
Current implementation of I/O stacks to PMU mapping doesn't support ICX-D.
Detect ICX-D system to disable mapping.
Fixes: 10337e95e0 ("perf/x86/intel/uncore: Enable I/O stacks to IIO PMON mapping on ICX")
Signed-off-by: Alexander Antonov <alexander.antonov@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221117122833.3103580-5-alexander.antonov@linux.intel.com
Current clear_attr_update procedure in pmu_set_mapping() sets attr_update
field in NULL that is not correct because intel_uncore_type pmu types can
contain several groups in attr_update field. For example, SPR platform
already has uncore_alias_group to update and then UPI topology group will
be added in next patches.
Fix current behavior and clear attr_update group related to mapping only.
Fixes: bb42b3d397 ("perf/x86/intel/uncore: Expose an Uncore unit to IIO PMON mapping")
Signed-off-by: Alexander Antonov <alexander.antonov@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221117122833.3103580-4-alexander.antonov@linux.intel.com
This patch introduces new 'uncore_upi_topology' topology type to support
UPI topology discovery.
Signed-off-by: Alexander Antonov <alexander.antonov@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20221117122833.3103580-3-alexander.antonov@linux.intel.com
Current implementation of uncore mapping doesn't support different types
of uncore PMUs which have its own topology context. This patch generalizes
Intel uncore topology implementation to be able easily introduce support
for new uncore blocks.
Signed-off-by: Alexander Antonov <alexander.antonov@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20221117122833.3103580-2-alexander.antonov@linux.intel.com
So far, only one pmu was allowed to be registered as core pmu and thus
IBS pmus were being registered as uncore. However, with the event context
rewrite, that limitation no longer exists and thus IBS pmus can also be
registered as core pmu. This makes IBS much more usable, for ex, user
will be able to do per-process precise monitoring on AMD:
Before patch:
$ sudo perf record -e cycles:pp ls
Error:
Invalid event (cycles:pp) in per-thread mode, enable system wide with '-a'
After patch:
$ sudo perf record -e cycles:pp ls
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.017 MB perf.data (33 samples) ]
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Ian Rogers <irogers@google.com>
Link: https://lkml.kernel.org/r/20221115093904.1799-1-ravi.bangoria@amd.com
The function 'amd_brs_disable_all' is declared twice in
commit ada543459c ("perf/x86/amd: Add AMD Fam19h Branch Sampling support").
Remove one of them.
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20221108104117.46642-1-zhangshaokun@hisilicon.com
struct p4_event_bind::cntr[][] should be signed because of
the following code:
int i, j;
for (i = 0; i < P4_CNTR_LIMIT; i++) {
---> j = bind->cntr[thread][i];
if (j != -1 && !test_bit(j, used_mask))
return j;
}
Making this member unsigned will make "j" 255 and fail "j != -1"
comparison.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Deal with errata TGL052, ADL037 and RPL017 "Trace May Contain Incorrect
Data When Configured With Single Range Output Larger Than 4KB" by
disabling single range output whenever larger than 4KB.
Fixes: 670638477a ("perf/x86/intel/pt: Opportunistically use single range output mode")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20221112151508.13768-1-adrian.hunter@intel.com
amd_pmu_enable_all() does:
if (!test_bit(idx, cpuc->active_mask))
continue;
amd_pmu_enable_event(cpuc->events[idx]);
A perf NMI of another event can come between these two steps. Perf NMI
handler internally disables and enables _all_ events, including the one
which nmi-intercepted amd_pmu_enable_all() was in process of enabling.
If that unintentionally enabled event has very low sampling period and
causes immediate successive NMI, causing the event to be throttled,
cpuc->events[idx] and cpuc->active_mask gets cleared by x86_pmu_stop().
This will result in amd_pmu_enable_event() getting called with event=NULL
when amd_pmu_enable_all() resumes after handling the NMIs. This causes a
kernel crash:
BUG: kernel NULL pointer dereference, address: 0000000000000198
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
[...]
Call Trace:
<TASK>
amd_pmu_enable_all+0x68/0xb0
ctx_resched+0xd9/0x150
event_function+0xb8/0x130
? hrtimer_start_range_ns+0x141/0x4a0
? perf_duration_warn+0x30/0x30
remote_function+0x4d/0x60
__flush_smp_call_function_queue+0xc4/0x500
flush_smp_call_function_queue+0x11d/0x1b0
do_idle+0x18f/0x2d0
cpu_startup_entry+0x19/0x20
start_secondary+0x121/0x160
secondary_startup_64_no_verify+0xe5/0xeb
</TASK>
amd_pmu_disable_all()/amd_pmu_enable_all() calls inside perf NMI handler
were recently added as part of BRS enablement but I'm not sure whether
we really need them. We can just disable BRS in the beginning and enable
it back while returning from NMI. This will solve the issue by not
enabling those events whose active_masks are set but are not yet enabled
in hw pmu.
Fixes: ada543459c ("perf/x86/amd: Add AMD Fam19h Branch Sampling support")
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20221114044029.373-1-ravi.bangoria@amd.com
Since the removal of function x86_pmu_update_cpu_context() by commit
983bd8543b5a ("perf: Rewrite core context handling"), there is no need to
query the type of the hybrid CPU inside function init_hw_perf_events().
Fixes: 983bd8543b5a ("perf: Rewrite core context handling")
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20221028203006.976831-1-rafaelmendsr@gmail.com
Drop the return value from x86_perf_get_lbr() and have the stub zero out
the @lbr structure instead of returning -1 to indicate "no LBR support".
KVM doesn't actually check the return value, and instead subtly relies on
zeroing the number of LBRs in intel_pmu_init().
Formalize "nr=0 means unsupported" so that KVM doesn't need to add a
pointless check on the return value to fix KVM's benign bug.
Note, the stub is necessary even though KVM x86 selects PERF_EVENTS and
the caller exists only when CONFIG_KVM_INTEL=y. Despite the name,
KVM_INTEL doesn't strictly require CPU_SUP_INTEL, it can be built with
any of INTEL || CENTAUR || ZHAOXIN CPUs.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20221006000314.73240-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The intel_pebs_isolation quirk checks both model number and stepping.
Cooper Lake has a different stepping (11) than the other Skylake Xeon.
It cannot benefit from the optimization in commit 9b545c04ab
("perf/x86/kvm: Avoid unnecessary work in guest filtering").
Add the stepping of Cooper Lake into the isolation_ucodes[] table.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20221031154550.571663-1-kan.liang@linux.intel.com
According to the latest event list, update the MEM_INST_RETIRED events
which support the DataLA facility.
Fixes: 6017608936 ("perf/x86/intel: Add Icelake support")
Reported-by: Jannis Klinkenberg <jannis.klinkenberg@rwth-aachen.de>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20221031154119.571386-1-kan.liang@linux.intel.com
Intel Xeon servers used to use a fixed energy resolution (15.3uj) for
Dram RAPL domain. But on SPR, Dram RAPL domain follows the standard
energy resolution as described in MSR_RAPL_POWER_UNIT.
Remove the SPR Dram energy unit quirk.
Fixes: bcfd218b66 ("perf/x86/rapl: Add support for Intel SPR platform")
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Tested-by: Wang Wendy <wendy.wang@intel.com>
Link: https://lkml.kernel.org/r/20220924054738.12076-3-rui.zhang@intel.com
There have been various issues and limitations with the way perf uses
(task) contexts to track events. Most notable is the single hardware
PMU task context, which has resulted in a number of yucky things (both
proposed and merged).
Notably:
- HW breakpoint PMU
- ARM big.little PMU / Intel ADL PMU
- Intel Branch Monitoring PMU
- AMD IBS PMU
- S390 cpum_cf PMU
- PowerPC trace_imc PMU
*Current design:*
Currently we have a per task and per cpu perf_event_contexts:
task_struct::perf_events_ctxp[] <-> perf_event_context <-> perf_cpu_context
^ | ^ | ^
`---------------------------------' | `--> pmu ---'
v ^
perf_event ------'
Each task has an array of pointers to a perf_event_context. Each
perf_event_context has a direct relation to a PMU and a group of
events for that PMU. The task related perf_event_context's have a
pointer back to that task.
Each PMU has a per-cpu pointer to a per-cpu perf_cpu_context, which
includes a perf_event_context, which again has a direct relation to
that PMU, and a group of events for that PMU.
The perf_cpu_context also tracks which task context is currently
associated with that CPU and includes a few other things like the
hrtimer for rotation etc.
Each perf_event is then associated with its PMU and one
perf_event_context.
*Proposed design:*
New design proposed by this patch reduce to a single task context and
a single CPU context but adds some intermediate data-structures:
task_struct::perf_event_ctxp -> perf_event_context <- perf_cpu_context
^ | ^ ^
`---------------------------' | |
| | perf_cpu_pmu_context <--.
| `----. ^ |
| | | |
| v v |
| ,--> perf_event_pmu_context |
| | |
| | |
v v |
perf_event ---> pmu ----------------'
With the new design, perf_event_context will hold all events for all
pmus in the (respective pinned/flexible) rbtrees. This can be achieved
by adding pmu to rbtree key:
{cpu, pmu, cgroup, group_index}
Each perf_event_context carries a list of perf_event_pmu_context which
is used to hold per-pmu-per-context state. For example, it keeps track
of currently active events for that pmu, a pmu specific task_ctx_data,
a flag to tell whether rotation is required or not etc.
Additionally, perf_cpu_pmu_context is used to hold per-pmu-per-cpu
state like hrtimer details to drive the event rotation, a pointer to
perf_event_pmu_context of currently running task and some other
ancillary information.
Each perf_event is associated to it's pmu, perf_event_context and
perf_event_pmu_context.
Further optimizations to current implementation are possible. For
example, ctx_resched() can be optimized to reschedule only single pmu
events.
Much thanks to Ravi for picking this up and pushing it towards
completion.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Co-developed-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20221008062424.313-1-ravi.bangoria@amd.com
PERF_MEM_LVLNUM_EXTN_MEM was introduced to cover CXL devices but it's
bit ambiguous name and also not generic enough to cover cxl.cache and
cxl.io devices. Rename it to PERF_MEM_LVLNUM_CXL to be more specific.
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/f6268268-b4e9-9ed6-0453-65792644d953@amd.com
Raptor Lake RAPL support is the same as previous Sky Lake.
Add Raptor Lake model for RAPL.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Wang Wendy <wendy.wang@intel.com>
Link: https://lkml.kernel.org/r/20221023125120.2727-2-rui.zhang@intel.com
AlderLake-N RAPL support is the same as previous Sky Lake.
Add AlderLake-N model for RAPL.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Wang Wendy <wendy.wang@intel.com>
Link: https://lkml.kernel.org/r/20221023125120.2727-1-rui.zhang@intel.com
clear_cpu_cap(&boot_cpu_data) is very similar to setup_clear_cpu_cap()
except that the latter also sets a bit in 'cpu_caps_cleared' which
later clears the same cap in secondary cpus, which is likely what is
meant here.
Fixes: 47125db27e ("perf/x86/intel/lbr: Support Architectural LBR")
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lkml.kernel.org/r/20220718141123.136106-2-mlevitsk@redhat.com
- PMU driver updates:
- Add AMD Last Branch Record Extension Version 2 (LbrExtV2)
feature support for Zen 4 processors.
- Extend the perf ABI to provide branch speculation information,
if available, and use this on CPUs that have it (eg. LbrExtV2).
- Improve Intel PEBS TSC timestamp handling & integration.
- Add Intel Raptor Lake S CPU support.
- Add 'perf mem' and 'perf c2c' memory profiling support on
AMD CPUs by utilizing IBS tagged load/store samples.
- Clean up & optimize various x86 PMU details.
- HW breakpoints:
- Big rework to optimize the code for systems with hundreds of CPUs and
thousands of breakpoints:
- Replace the nr_bp_mutex global mutex with the bp_cpuinfo_sem
per-CPU rwsem that is read-locked during most of the key operations.
- Improve the O(#cpus * #tasks) logic in toggle_bp_slot()
and fetch_bp_busy_slots().
- Apply micro-optimizations & cleanups.
- Misc cleanups & enhancements.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQJFBAABCgAvFiEEBpT5eoXrXCwVQwEKEnMQ0APhK1gFAmM/2pMRHG1pbmdvQGtl
cm5lbC5vcmcACgkQEnMQ0APhK1iIMA/+J+MCEVTt9kwZeBtHoPX7iZ5gnq1+McoQ
f6ALX19AO/ZSuA7EBA3cS3Ny5eyGy3ofYUnRW+POezu9CpflLW/5N27R2qkZFrWC
A09B86WH676ZrmXt+oI05rpZ2y/NGw4gJxLLa4/bWF3g9xLfo21i+YGKwdOnNFpl
DEdCVHtjlMcOAU3+on6fOYuhXDcYd7PKGcCfLE7muOMOAtwyj0bUDBt7m+hneZgy
qbZHzDU2DZ5L/LXiMyuZj5rC7V4xUbfZZfXglG38YCW1WTieS3IjefaU2tREhu7I
rRkCK48ULDNNJR3dZK8IzXJRxusq1ICPG68I+nm/K37oZyTZWtfYZWehW/d/TnPa
tUiTwimabz7UUqaGq9ZptxwINcAigax0nl6dZ3EseeGhkDE6j71/3kqrkKPz4jth
+fCwHLOrI3c4Gq5qWgPvqcUlUneKf3DlOMtzPKYg7sMhla2zQmFpYCPzKfm77U/Z
BclGOH3FiwaK6MIjPJRUXTePXqnUseqCR8PCH/UPQUeBEVHFcMvqCaa15nALed8x
dFi76VywR9mahouuLNq6sUNePlvDd2B124PygNwegLlBfY9QmKONg9qRKOnQpuJ6
UprRJjLOOucZ/N/jn6+ShHkqmXsnY2MhfUoHUoMQ0QAI+n++e+2AuePo251kKWr8
QlqKxd9PMQU=
=LcGg
-----END PGP SIGNATURE-----
Merge tag 'perf-core-2022-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf events updates from Ingo Molnar:
"PMU driver updates:
- Add AMD Last Branch Record Extension Version 2 (LbrExtV2) feature
support for Zen 4 processors.
- Extend the perf ABI to provide branch speculation information, if
available, and use this on CPUs that have it (eg. LbrExtV2).
- Improve Intel PEBS TSC timestamp handling & integration.
- Add Intel Raptor Lake S CPU support.
- Add 'perf mem' and 'perf c2c' memory profiling support on AMD CPUs
by utilizing IBS tagged load/store samples.
- Clean up & optimize various x86 PMU details.
HW breakpoints:
- Big rework to optimize the code for systems with hundreds of CPUs
and thousands of breakpoints:
- Replace the nr_bp_mutex global mutex with the bp_cpuinfo_sem
per-CPU rwsem that is read-locked during most of the key
operations.
- Improve the O(#cpus * #tasks) logic in toggle_bp_slot() and
fetch_bp_busy_slots().
- Apply micro-optimizations & cleanups.
- Misc cleanups & enhancements"
* tag 'perf-core-2022-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (75 commits)
perf/hw_breakpoint: Annotate tsk->perf_event_mutex vs ctx->mutex
perf: Fix pmu_filter_match()
perf: Fix lockdep_assert_event_ctx()
perf/x86/amd/lbr: Adjust LBR regardless of filtering
perf/x86/utils: Fix uninitialized var in get_branch_type()
perf/uapi: Define PERF_MEM_SNOOPX_PEER in kernel header file
perf/x86/amd: Support PERF_SAMPLE_PHY_ADDR
perf/x86/amd: Support PERF_SAMPLE_ADDR
perf/x86/amd: Support PERF_SAMPLE_{WEIGHT|WEIGHT_STRUCT}
perf/x86/amd: Support PERF_SAMPLE_DATA_SRC
perf/x86/amd: Add IBS OP_DATA2 DataSrc bit definitions
perf/mem: Introduce PERF_MEM_LVLNUM_{EXTN_MEM|IO}
perf/x86/uncore: Add new Raptor Lake S support
perf/x86/cstate: Add new Raptor Lake S support
perf/x86/msr: Add new Raptor Lake S support
perf/x86: Add new Raptor Lake S support
bpf: Check flags for branch stack in bpf_read_branch_records helper
perf, hw_breakpoint: Fix use-after-free if perf_event_open() fails
perf: Use sample_flags for raw_data
perf: Use sample_flags for addr
...
In case of fused compare and taken branch instructions, the AMD LBR points to
the compare instruction instead of the branch. Users of LBR usually expects
the from address to point to a branch instruction. The kernel has code to
adjust the from address via get_branch_type_fused(). However this correction
is only applied when a branch filter is applied. That means that if no
filter is present, the quality of the data is lower.
Fix the problem by applying the adjustment regardless of the filter setting,
bringing the AMD LBR to the same level as other LBR implementations.
Fixes: 245268c19f ("perf/x86/amd/lbr: Use fusion-aware branch classifier")
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Sandipan Das <sandipan.das@amd.com>
Link: https://lore.kernel.org/r/20220928184043.408364-3-eranian@google.com
offset is passed as a pointer and on certain call path is not set by the
function. If the caller does not re-initialize offset between calls, value
could be inherited between calls. Prevent this by initializing offset on each
call.
This impacts the code in amd_pmu_lbr_filter() which does:
for(i=0; ...) {
ret = get_branch_type_fused(..., &offset);
if (offset)
lbr_entries[i].from += offset;
}
Fixes: df3e9612f7 ("perf/x86: Make branch classifier fusion-aware")
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Sandipan Das <sandipan.das@amd.com>
Link: https://lore.kernel.org/r/20220928184043.408364-2-eranian@google.com
IBS_DC_PHYSADDR provides the physical data address for the tagged load/
store operation. Populate perf sample physical address using it.
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220928095805.596-7-ravi.bangoria@amd.com
IBS_DC_LINADDR provides the linear data address for the tagged load/
store operation. Populate perf sample address using it.
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220928095805.596-6-ravi.bangoria@amd.com
IbsDcMissLat indicates the number of clock cycles from when a miss is
detected in the data cache to when the data was delivered to the core.
Similarly, IbsTagToRetCtr provides number of cycles from when the op
was tagged to when the op was retired. Consider these fields for
sample->weight.
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220928095805.596-5-ravi.bangoria@amd.com
struct perf_mem_data_src is used to pass arch specific memory access
details into generic form. These details gets consumed by tools like
perf mem and c2c. IBS tagged load/store sample provides most of the
information needed for these tools. Add a logic to convert IBS
specific raw data into perf_mem_data_src.
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220928095805.596-4-ravi.bangoria@amd.com
From the perspective of the uncore PMU, the new Raptor Lake S is the
same as the other hybrid {ALDER,RAPTOP}LAKE.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220928153331.3757388-4-kan.liang@linux.intel.com
From the perspective of Intel cstate residency counters, the new
Raptor Lake S is the same as the other hybrid {ALDER,RAPTOP}LAKE.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220928153331.3757388-3-kan.liang@linux.intel.com
The same as the other hybrid {ALDER,RAPTOP}LAKE, the new Raptor Lake S
also support PPERF and SMI_COUNT MSRs.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220928153331.3757388-2-kan.liang@linux.intel.com
Use the new sample_flags to indicate whether the raw data field is
filled by the PMU driver. Although it could check with the NULL,
follow the same rule with other fields.
Remove the raw field from the perf_sample_data_init() to minimize
the number of cache lines touched.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220921220032.2858517-2-namhyung@kernel.org
Use the new sample_flags to indicate whether the addr field is filled by
the PMU driver. As most PMU drivers pass 0, it can set the flag only if
it has a non-zero value. And use 0 in perf_sample_output() if it's not
filled already.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220921220032.2858517-1-namhyung@kernel.org
So that it can call perf_callchain() only if needed. Historically it used
__PERF_SAMPLE_CALLCHAIN_EARLY but we can do that with sample_flags in the
struct perf_sample_data.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220908214104.3851807-1-namhyung@kernel.org
All the fixed counters share a fixed control register. The current
perf reads and re-writes the fixed control register for each fixed
counter disable/enable, which is unnecessary.
When changing the fixed control register, the entire PMU must be
disabled via the global control register. The changing cannot be taken
effect until the entire PMU is re-enabled. Only updating the fixed
control register once right before the entire PMU re-enabling is
enough.
The read of the fixed control register is not necessary either. The
value can be cached in the per CPU cpu_hw_events.
Test results:
Counting all the fixed counters with the perf bench sched pipe as below
on a SPR machine.
$perf stat -e cycles,instructions,ref-cycles,slots --no-inherit --
taskset -c 1 perf bench sched pipe
The Total elapsed time reduces from 5.36s (without the patch) to 4.99s
(with the patch), which is ~6.9% improvement.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220804140729.2951259-1-kan.liang@linux.intel.com
Now that it is all internal to the intel driver, remove
x86_pmu::update_topdown_event.
Assumes that is_topdown_count(event) can only be true when the
hardware has topdown stuff and the function is set.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220829101321.771635301@infradead.org
Ensure all platform specific event flags are within PERF_EVENT_FLAG_ARCH.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: James Clark <james.clark@arm.com>
Link: https://lkml.kernel.org/r/20220907091924.439193-5-anshuman.khandual@arm.com
Use the new sample_flags to indicate whether the txn field is filled by
the PMU driver.
Remove the txn field from the perf_sample_data_init() to minimize the
number of cache lines touched.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220901130959.1285717-7-kan.liang@linux.intel.com
Use the new sample_flags to indicate whether the data_src field is
filled by the PMU driver.
Remove the data_src field from the perf_sample_data_init() to minimize
the number of cache lines touched.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220901130959.1285717-6-kan.liang@linux.intel.com
Use the new sample_flags to indicate whether the weight field is filled
by the PMU driver.
Remove the weight field from the perf_sample_data_init() to minimize the
number of cache lines touched.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220901130959.1285717-5-kan.liang@linux.intel.com
Use the new sample_flags to indicate whether the branch stack is filled
by the PMU driver.
Remove the br_stack from the perf_sample_data_init() to minimize the number
of cache lines touched.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220901130959.1285717-4-kan.liang@linux.intel.com
The PEBS TSC-based timestamps do not appear correctly in the final
perf.data output file from perf record.
The data->time field setup by PEBS in the setup_pebs_fixed_sample_data()
is later overwritten by perf_events generic code in
perf_prepare_sample(). There is an ordering problem.
Set the sample flags when the data->time is updated by PEBS.
The data->time field will not be overwritten anymore.
Reported-by: Andreas Kogler <andreas.kogler.0x@gmail.com>
Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220901130959.1285717-3-kan.liang@linux.intel.com
When a guest PEBS counter is cross-mapped by a host counter, software
will remove the corresponding bit in the arr[global_ctrl].guest and
expect hardware to perform a change of state "from enable to disable"
via the msr_slot[] switch during the vmx transaction.
The real world is that if user adjust the counter overflow value small
enough, it still opens a tiny race window for the previously PEBS-enabled
counter to write cross-mapped PEBS records into the guest's PEBS buffer,
when arr[global_ctrl].guest has been prioritised (switch_msr_special stuff)
to switch into the enabled state, while the arr[pebs_enable].guest has not.
Close this window by clearing invalid bits in the arr[global_ctrl].guest.
Cc: linux-perf-users@vger.kernel.org
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sean Christopherson <seanjc@google.com>
Fixes: 854250329c ("KVM: x86/pmu: Disable guest PEBS temporarily in two rare situations")
Signed-off-by: Like Xu <likexu@tencent.com>
Message-Id: <20220831033524.58561-1-likexu@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When a guest PEBS counter is cross-mapped by a host counter, software
will remove the corresponding bit in the arr[global_ctrl].guest and
expect hardware to perform a change of state "from enable to disable"
via the msr_slot[] switch during the vmx transaction.
The real world is that if user adjust the counter overflow value small
enough, it still opens a tiny race window for the previously PEBS-enabled
counter to write cross-mapped PEBS records into the guest's PEBS buffer,
when arr[global_ctrl].guest has been prioritised (switch_msr_special stuff)
to switch into the enabled state, while the arr[pebs_enable].guest has not.
Close this window by clearing invalid bits in the arr[global_ctrl].guest.
Fixes: 854250329c ("KVM: x86/pmu: Disable guest PEBS temporarily in two rare situations")
Signed-off-by: Like Xu <likexu@tencent.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220831033524.58561-1-likexu@tencent.com
For some Alder Lake N machine, the below unchecked MSR access error may be
triggered.
[ 0.088017] rcu: Hierarchical SRCU implementation.
[ 0.088017] unchecked MSR access error: WRMSR to 0x38f (tried to write
0x0001000f0000003f) at rIP: 0xffffffffb5684de8 (native_write_msr+0x8/0x30)
[ 0.088017] Call Trace:
[ 0.088017] <TASK>
[ 0.088017] __intel_pmu_enable_all.constprop.46+0x4a/0xa0
The Alder Lake N only has e-cores. The X86_FEATURE_HYBRID_CPU flag is
not set. The perf cannot retrieve the correct CPU type via
get_this_hybrid_cpu_type(). The model specific get_hybrid_cpu_type() is
hardcode to p-core. The wrong CPU type is given to the PMU of the
Alder Lake N.
Since Alder Lake N isn't in fact a hybrid CPU, remove ALDERLAKE_N from
the rest of {ALDER,RAPTOP}LAKE and create a non-hybrid PMU setup.
The differences between Gracemont and the previous Tremont are,
- Number of GP counters
- Load and store latency Events
- PEBS event_constraints
- Instruction Latency support
- Data source encoding
- Memory access latency encoding
Fixes: c2a960f7c5 ("perf/x86: Add new Alder Lake and Raptor Lake support")
Reported-by: Jianfeng Gao <jianfeng.gao@intel.com>
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220831142702.153110-1-kan.liang@linux.intel.com
This expands generic branch type classification by adding two more entries
there in i.e system error and not in transaction. This also updates the x86
implementation to process X86_BR_NO_TX records as appropriate. This changes
branch types reported to user space on x86 platform but it should not be a
problem. The possible scenarios and impacts are enumerated here.
--------------------------------------------------------------------------
| kernel | perf tool | Impact |
--------------------------------------------------------------------------
| old | old | Works as before |
--------------------------------------------------------------------------
| old | new | PERF_BR_UNKNOWN is processed |
--------------------------------------------------------------------------
| new | old | PERF_BR_NO_TX is blocked via old PERF_BR_MAX |
--------------------------------------------------------------------------
| new | new | PERF_BR_NO_TX is recognized |
--------------------------------------------------------------------------
When PERF_BR_NO_TX is blocked via old PERF_BR_MAX (new kernel with old perf
tool) the user space might throw up an warning complaining about an
unrecognized branch types being reported, but it's expected. PERF_BR_SERROR
& PERF_BR_NO_TX branch types will be used for BRBE implementation on arm64
platform.
PERF_BR_NO_TX complements 'abort' and 'in_tx' elements in perf_branch_entry
which represent other transaction states for a given branch record. Because
this completes the transaction state classification.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: James Clark <james.clark@arm.com>
Link: https://lkml.kernel.org/r/20220824044822.70230-2-anshuman.khandual@arm.com
Provide branch speculation information captured via AMD Last Branch Record
Extension Version 2 (LbrExtV2) by setting the speculation info in branch
records. The info is based on the "valid" and "spec" bits in the Branch To
registers.
Suggested-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/ddc02f6320464cad0e3ff5bdb2314531568a91bc.1660211399.git.sandipan.das@amd.com
AMD Last Branch Record Extension Version 2 (LbrExtV2) can report a branch
from address that points to an instruction preceding the actual branch by
several bytes due to branch fusion and further optimizations in Zen4
processors.
In such cases, software should move forward sequentially in the instruction
stream from the reported address and the address of the first branch
encountered should be used instead. Hence, use the fusion-aware branch
classifier to determine the correct branch type and get the offset for
adjusting the branch from address.
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/c324d2d0a9c3976da30b9563d09e50bfee0f264d.1660211399.git.sandipan.das@amd.com
With branch fusion and other optimizations, branch sampling hardware in
some processors can report a branch from address that points to an
instruction preceding the actual branch by several bytes.
In such cases, the classifier cannot determine the branch type which leads
to failures such as with the recently added test from commit b55878c90a
("perf test: Add test for branch stack sampling"). Branch information is
also easier to consume and annotate if branch from addresses always point
to branch instructions.
Add a new variant of the branch classifier that can account for instruction
fusion. If fusion is expected and the current branch from address does not
point to a branch instruction, it attempts to find the first branch within
the next (MAX_INSN_SIZE - 1) bytes and if found, additionally provides the
offset between the reported branch from address and the address of the
expected branch instruction.
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/b6bb0abaa8a54c0b6d716344700ee11a1793d709.1660211399.git.sandipan.das@amd.com
With AMD Last Branch Record Extension Version 2 (LbrExtV2), it is necessary
to process the branch records further as hardware filtering is not granular
enough for identifying certain types of branches. E.g. to record system
calls, one should record far branches. The filter captures both far calls
and far returns but the irrelevant records are filtered out based on the
branch type as seen by the branch classifier.
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/e51de057517f77788abd393c832e8dea616d489c.1660211399.git.sandipan.das@amd.com
Commit 3e702ff6d1 ("perf/x86: Add LBR software filter support for Intel
CPUs") introduces a software branch filter which complements the hardware
branch filter and adds an x86 branch classifier.
Move the branch classifier to arch/x86/events/ so that it can be utilized
by other vendors for branch record filtering.
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/bae5b95470d6bd49f40954bd379f414f5afcb965.1660211399.git.sandipan.das@amd.com
If AMD Last Branch Record Extension Version 2 (LbrExtV2) is detected,
convert the requested branch filter (PERF_SAMPLE_BRANCH_* flags) to the
corresponding hardware filter value and stash it in the event data when
a branch stack is requested. The hardware filter value is also saved in
per-CPU areas for use during event scheduling.
Hardware filtering is provided by the LBR Branch Select register. It has
bits which when set, suppress recording of the following types of branches:
* CPL = 0 (Kernel only)
* CPL > 0 (Userspace only)
* Conditional Branches
* Near Relative Calls
* Near Indirect Calls
* Near Returns
* Near Indirect Jumps (excluding Near Indirect Calls and Near Returns)
* Near Relative Jumps (excluding Near Relative Calls)
* Far Branches
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/9336af5c9785b8e14c62220fc0e6cfb10ab97de3.1660211399.git.sandipan.das@amd.com
If AMD Last Branch Record Extension Version 2 (LbrExtV2) is detected,
enable it alongside LBR Freeze on PMI when an event requests branch stack
i.e. PERF_SAMPLE_BRANCH_STACK.
Each branch record is represented by a pair of registers, LBR From and LBR
To. The freeze feature prevents any updates to these registers once a PMC
overflows. The contents remain unchanged until the freeze bit is cleared by
the PMI handler.
The branch records are read and copied to sample data before unfreezing.
However, only valid entries are copied. There is no additional register to
denote which of the register pairs represent the top of the stack (TOS)
since internal register renaming always ensures that the first pair (i.e.
index 0) is the one representing the most recent branch and so on.
The LBR registers are per-thread resources and are cleared explicitly
whenever a new task is scheduled in. There are no special implications on
the contents of these registers when transitioning to deep C-states.
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/d3b8500a3627a0d4d0259b005891ee248f248d91.1660211399.git.sandipan.das@amd.com
AMD Last Branch Record Extension Version 2 (LbrExtV2) is driven by Core PMC
overflows. It records recently taken branches up to the moment when the PMC
overflow occurs.
Detect the feature during PMU initialization and set the branch stack depth
using CPUID leaf 0x80000022 EBX.
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/fc6e45378ada258f1bab79b0de6e05c393a8f1dd.1660211399.git.sandipan.das@amd.com
AMD processors that are capable of recording branches support either Branch
Sampling (BRS) or Last Branch Record (LBR). In preparation for adding Last
Branch Record Extension Version 2 (LbrExtV2) support, introduce new static
calls which act as gateways to call into the feature-dependent functions
based on what is available on the processor.
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/b75dbc32663cb395f0d701167e952c6a6b0445a3.1660211399.git.sandipan.das@amd.com
AMD processors that are capable of recording branches support either Branch
Sampling (BRS) or Last Branch Record (LBR). In preparation for adding Last
Branch Record Extension Version 2 (LbrExtV2) support, reuse the "branches"
capability to advertise information about both BRS and LBR but make the
"branch-brs" event exclusive to Family 19h processors that support BRS.
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/ba4a4cde6db79b1c65c49834027bbdb8a915546b.1660211399.git.sandipan.das@amd.com
Existing code was generating bogus counts for the SNB IMC bandwidth counters:
$ perf stat -a -I 1000 -e uncore_imc/data_reads/,uncore_imc/data_writes/
1.000327813 1,024.03 MiB uncore_imc/data_reads/
1.000327813 20.73 MiB uncore_imc/data_writes/
2.000580153 261,120.00 MiB uncore_imc/data_reads/
2.000580153 23.28 MiB uncore_imc/data_writes/
The problem was introduced by commit:
07ce734dd8 ("perf/x86/intel/uncore: Clean up client IMC")
Where the read_counter callback was replace to point to the generic
uncore_mmio_read_counter() function.
The SNB IMC counters are freerunnig 32-bit counters laid out contiguously in
MMIO. But uncore_mmio_read_counter() is using a readq() call to read from
MMIO therefore reading 64-bit from MMIO. Although this is okay for the
uncore_perf_event_update() function because it is shifting the value based
on the actual counter width to compute a delta, it is not okay for the
uncore_pmu_event_start() which is simply reading the counter and therefore
priming the event->prev_count with a bogus value which is responsible for
causing bogus deltas in the perf stat command above.
The fix is to reintroduce the custom callback for read_counter for the SNB
IMC PMU and use readl() instead of readq(). With the change the output of
perf stat is back to normal:
$ perf stat -a -I 1000 -e uncore_imc/data_reads/,uncore_imc/data_writes/
1.000120987 296.94 MiB uncore_imc/data_reads/
1.000120987 138.42 MiB uncore_imc/data_writes/
2.000403144 175.91 MiB uncore_imc/data_reads/
2.000403144 68.50 MiB uncore_imc/data_writes/
Fixes: 07ce734dd8 ("perf/x86/intel/uncore: Clean up client IMC")
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20220803160031.1379788-1-eranian@google.com
According to the latest event list, the LOAD_LATENCY PEBS event only
works on the GP counter 0 and 1 for ADL and RPL.
Update the pebs event constraints table.
Fixes: f83d2f91d2 ("perf/x86/intel: Add Alder Lake Hybrid support")
Reported-by: Ammy Yi <ammy.yi@intel.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20220818184429.2355857-1-kan.liang@linux.intel.com
With the existing code in store_latency_data(), the memory operation (mem_op)
returned to the user is always OP_LOAD where in fact, it should be OP_STORE.
This comes from the fact that the function is simply grabbing the information
from a data source map which covers only load accesses. Intel 12th gen CPU
offers precise store sampling that captures both the data source and latency.
Therefore it can use the data source mapping table but must override the
memory operation to reflect stores instead of loads.
Fixes: 61b985e3e7 ("perf/x86/intel: Add perf core PMU support for Sapphire Rapids")
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220818054613.1548130-1-eranian@google.com
The SDM explicitly states that PEBS Baseline implies Extended PEBS.
For cpu model forward compatibility (e.g. on ICX, SPR, ADL), it's
safe to stop doing FMS table thing such as setting pebs_capable and
PMU_FL_PEBS_ALL since it's already set in the intel_ds_init().
The Goldmont Plus is the only platform which supports extended PEBS
but doesn't have Baseline. Keep the status quo.
Reported-by: Like Xu <likexu@tencent.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lkml.kernel.org/r/20220816114057.51307-1-likexu@tencent.com
On the platform with Arch LBR, the HW raw branch type encoding may leak
to the perf tool when the SAVE_TYPE option is not set.
In the intel_pmu_store_lbr(), the HW raw branch type is stored in
lbr_entries[].type. If the SAVE_TYPE option is set, the
lbr_entries[].type will be converted into the generic PERF_BR_* type
in the intel_pmu_lbr_filter() and exposed to the user tools.
But if the SAVE_TYPE option is NOT set by the user, the current perf
kernel doesn't clear the field. The HW raw branch type leaks.
There are two solutions to fix the issue for the Arch LBR.
One is to clear the field if the SAVE_TYPE option is NOT set.
The other solution is to unconditionally convert the branch type and
expose the generic type to the user tools.
The latter is implemented here, because
- The branch type is valuable information. I don't see a case where
you would not benefit from the branch type. (Stephane Eranian)
- Not having the branch type DOES NOT save any space in the
branch record (Stephane Eranian)
- The Arch LBR HW can retrieve the common branch types from the
LBR_INFO. It doesn't require the high overhead SW disassemble.
Fixes: 47125db27e ("perf/x86/intel/lbr: Support Architectural LBR")
Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20220816125612.2042397-1-kan.liang@linux.intel.com
* Unwinder implementations for both nVHE modes (classic and
protected), complete with an overflow stack
* Rework of the sysreg access from userspace, with a complete
rewrite of the vgic-v3 view to allign with the rest of the
infrastructure
* Disagregation of the vcpu flags in separate sets to better track
their use model.
* A fix for the GICv2-on-v3 selftest
* A small set of cosmetic fixes
RISC-V:
* Track ISA extensions used by Guest using bitmap
* Added system instruction emulation framework
* Added CSR emulation framework
* Added gfp_custom flag in struct kvm_mmu_memory_cache
* Added G-stage ioremap() and iounmap() functions
* Added support for Svpbmt inside Guest
s390:
* add an interface to provide a hypervisor dump for secure guests
* improve selftests to use TAP interface
* enable interpretive execution of zPCI instructions (for PCI passthrough)
* First part of deferred teardown
* CPU Topology
* PV attestation
* Minor fixes
x86:
* Permit guests to ignore single-bit ECC errors
* Intel IPI virtualization
* Allow getting/setting pending triple fault with KVM_GET/SET_VCPU_EVENTS
* PEBS virtualization
* Simplify PMU emulation by just using PERF_TYPE_RAW events
* More accurate event reinjection on SVM (avoid retrying instructions)
* Allow getting/setting the state of the speaker port data bit
* Refuse starting the kvm-intel module if VM-Entry/VM-Exit controls are inconsistent
* "Notify" VM exit (detect microarchitectural hangs) for Intel
* Use try_cmpxchg64 instead of cmpxchg64
* Ignore benign host accesses to PMU MSRs when PMU is disabled
* Allow disabling KVM's "MONITOR/MWAIT are NOPs!" behavior
* Allow NX huge page mitigation to be disabled on a per-vm basis
* Port eager page splitting to shadow MMU as well
* Enable CMCI capability by default and handle injected UCNA errors
* Expose pid of vcpu threads in debugfs
* x2AVIC support for AMD
* cleanup PIO emulation
* Fixes for LLDT/LTR emulation
* Don't require refcounted "struct page" to create huge SPTEs
* Miscellaneous cleanups:
** MCE MSR emulation
** Use separate namespaces for guest PTEs and shadow PTEs bitmasks
** PIO emulation
** Reorganize rmap API, mostly around rmap destruction
** Do not workaround very old KVM bugs for L0 that runs with nesting enabled
** new selftests API for CPUID
Generic:
* Fix races in gfn->pfn cache refresh; do not pin pages tracked by the cache
* new selftests API using struct kvm_vcpu instead of a (vm, id) tuple
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmLnyo4UHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMtQQf/XjVWiRcWLPR9dqzRM/vvRXpiG+UL
jU93R7m6ma99aqTtrxV/AE+kHgamBlma3Cwo+AcWk9uCVNbIhFjv2YKg6HptKU0e
oJT3zRYp+XIjEo7Kfw+TwroZbTlG6gN83l1oBLFMqiFmHsMLnXSI2mm8MXyi3dNB
vR2uIcTAl58KIprqNNsYJ2dNn74ogOMiXYx9XzoA9/5Xb6c0h4rreHJa5t+0s9RO
Gz7Io3PxumgsbJngjyL1Ve5oxhlIAcZA8DU0PQmjxo3eS+k6BcmavGFd45gNL5zg
iLpCh4k86spmzh8CWkAAwWPQE4dZknK6jTctJc0OFVad3Z7+X7n0E8TFrA==
=PM8o
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"Quite a large pull request due to a selftest API overhaul and some
patches that had come in too late for 5.19.
ARM:
- Unwinder implementations for both nVHE modes (classic and
protected), complete with an overflow stack
- Rework of the sysreg access from userspace, with a complete rewrite
of the vgic-v3 view to allign with the rest of the infrastructure
- Disagregation of the vcpu flags in separate sets to better track
their use model.
- A fix for the GICv2-on-v3 selftest
- A small set of cosmetic fixes
RISC-V:
- Track ISA extensions used by Guest using bitmap
- Added system instruction emulation framework
- Added CSR emulation framework
- Added gfp_custom flag in struct kvm_mmu_memory_cache
- Added G-stage ioremap() and iounmap() functions
- Added support for Svpbmt inside Guest
s390:
- add an interface to provide a hypervisor dump for secure guests
- improve selftests to use TAP interface
- enable interpretive execution of zPCI instructions (for PCI
passthrough)
- First part of deferred teardown
- CPU Topology
- PV attestation
- Minor fixes
x86:
- Permit guests to ignore single-bit ECC errors
- Intel IPI virtualization
- Allow getting/setting pending triple fault with
KVM_GET/SET_VCPU_EVENTS
- PEBS virtualization
- Simplify PMU emulation by just using PERF_TYPE_RAW events
- More accurate event reinjection on SVM (avoid retrying
instructions)
- Allow getting/setting the state of the speaker port data bit
- Refuse starting the kvm-intel module if VM-Entry/VM-Exit controls
are inconsistent
- "Notify" VM exit (detect microarchitectural hangs) for Intel
- Use try_cmpxchg64 instead of cmpxchg64
- Ignore benign host accesses to PMU MSRs when PMU is disabled
- Allow disabling KVM's "MONITOR/MWAIT are NOPs!" behavior
- Allow NX huge page mitigation to be disabled on a per-vm basis
- Port eager page splitting to shadow MMU as well
- Enable CMCI capability by default and handle injected UCNA errors
- Expose pid of vcpu threads in debugfs
- x2AVIC support for AMD
- cleanup PIO emulation
- Fixes for LLDT/LTR emulation
- Don't require refcounted "struct page" to create huge SPTEs
- Miscellaneous cleanups:
- MCE MSR emulation
- Use separate namespaces for guest PTEs and shadow PTEs bitmasks
- PIO emulation
- Reorganize rmap API, mostly around rmap destruction
- Do not workaround very old KVM bugs for L0 that runs with nesting enabled
- new selftests API for CPUID
Generic:
- Fix races in gfn->pfn cache refresh; do not pin pages tracked by
the cache
- new selftests API using struct kvm_vcpu instead of a (vm, id)
tuple"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (606 commits)
selftests: kvm: set rax before vmcall
selftests: KVM: Add exponent check for boolean stats
selftests: KVM: Provide descriptive assertions in kvm_binary_stats_test
selftests: KVM: Check stat name before other fields
KVM: x86/mmu: remove unused variable
RISC-V: KVM: Add support for Svpbmt inside Guest/VM
RISC-V: KVM: Use PAGE_KERNEL_IO in kvm_riscv_gstage_ioremap()
RISC-V: KVM: Add G-stage ioremap() and iounmap() functions
KVM: Add gfp_custom flag in struct kvm_mmu_memory_cache
RISC-V: KVM: Add extensible CSR emulation framework
RISC-V: KVM: Add extensible system instruction emulation framework
RISC-V: KVM: Factor-out instruction emulation into separate sources
RISC-V: KVM: move preempt_disable() call in kvm_arch_vcpu_ioctl_run
RISC-V: KVM: Make kvm_riscv_guest_timer_init a void function
RISC-V: KVM: Fix variable spelling mistake
RISC-V: KVM: Improve ISA extension by using a bitmap
KVM, x86/mmu: Fix the comment around kvm_tdp_mmu_zap_leafs()
KVM: SVM: Dump Virtual Machine Save Area (VMSA) to klog
KVM: x86/mmu: Treat NX as a valid SPTE bit for NPT
KVM: x86: Do not block APIC write for non ICR registers
...
