Change the clock property in the TH1520 SPI controller node to a clock
provided by AP_SYS clock controller.
Remove spi_clk fixed clock reference from BeagleV Ahead and LPI4a dts.
Link: https://git.beagleboard.org/beaglev-ahead/beaglev-ahead/-/tree/main/docs
Signed-off-by: Drew Fustini <dfustini@tenstorrent.com>
Add clock property to TH1520 gpio controller nodes. These clock gates
refer to corresponding enable bits in the peripheral clock gate control
register. Refer to register PERI_CLK_CFG in section 4.4.2.2.52 of the
TH1520 System User Manual.
Link: https://git.beagleboard.org/beaglev-ahead/beaglev-ahead/-/tree/main/docs
Signed-off-by: Drew Fustini <dfustini@tenstorrent.com>
Change the dma-controller and timer nodes to use the APB clock provided
by the AP_SUBSYS clock controller.
Remove apb_clk reference from BeagleV Ahead and LPI4a dts.
Link: https://git.beagleboard.org/beaglev-ahead/beaglev-ahead/-/tree/main/docs
Signed-off-by: Drew Fustini <dfustini@tenstorrent.com>
Change the clock property in the TH1520 mmc controller nodes to a clock
provided by AP_SYS clock controller.
Remove sdhci fixed clock reference from BeagleV Ahead and LPI4a dts.
Link: https://git.beagleboard.org/beaglev-ahead/beaglev-ahead/-/tree/main/docs
Signed-off-by: Drew Fustini <dfustini@tenstorrent.com>
created spi0 node with fixed clock. the spi0 node
uses synopsis designware driver and has the following
compatible "snps,dw-apb-ssi". the spi0 node is connected
to a SPI NOR flash pad which is left unpopulated on the back
side of the board.
Acked-by: Drew Fustini <drew@pdp7.com>
Signed-off-by: Kanak Shilledar <kanakshilledar@gmail.com>
Signed-off-by: Drew Fustini <drew@pdp7.com>
Here is a small set of tty and serial driver updates for 6.11-rc1. Not
much happened this cycle, unlike the previous kernel release which had
lots of "excitement" in this part of the kernel. Included in here are
the following changes:
- dt binding updates for new platforms
- 8250 driver updates
- various small serial driver fixes and updates
- printk/console naming and matching attempt #2 (was reverted for
6.10-final, should be good to go this time around, acked by the
relevant maintainers).
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZppbCQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymV1ACeIY5kgipqY7w4d3/7PcpKMiftrisAn0hr6csj
Gan+k3cuVGlasGkaQ5/B
=35VK
-----END PGP SIGNATURE-----
Merge tag 'tty-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is a small set of tty and serial driver updates for 6.11-rc1. Not
much happened this cycle, unlike the previous kernel release which had
lots of "excitement" in this part of the kernel. Included in here are
the following changes:
- dt binding updates for new platforms
- 8250 driver updates
- various small serial driver fixes and updates
- printk/console naming and matching attempt #2 (was reverted for
6.10-final, should be good to go this time around, acked by the
relevant maintainers).
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (22 commits)
Documentation: kernel-parameters: Add DEVNAME:0.0 format for serial ports
serial: core: Add serial_base_match_and_update_preferred_console()
printk: Add match_devname_and_update_preferred_console()
serial: sc16is7xx: hardware reset chip if reset-gpios is defined in DT
dt-bindings: serial: sc16is7xx: add reset-gpios
dt-bindings: serial: vt8500-uart: convert to json-schema
serial: 8250_platform: Explicitly show we initialise ISA ports only once
tty: add missing MODULE_DESCRIPTION() macros
dt-bindings: serial: mediatek,uart: add MT7988
serial: sh-sci: Add support for RZ/V2H(P) SoC
dt-bindings: serial: Add documentation for Renesas RZ/V2H(P) (R9A09G057) SCIF support
dt-bindings: serial: renesas,scif: Make 'interrupt-names' property as required
dt-bindings: serial: renesas,scif: Validate 'interrupts' and 'interrupt-names'
dt-bindings: serial: renesas,scif: Move ref for serial.yaml at the end
riscv: dts: starfive: jh7110: Add the core reset and jh7110 compatible for uarts
serial: 8250_dw: Use reset array API to get resets
dt-bindings: serial: snps-dw-apb-uart: Add one more reset signal for StarFive JH7110 SoC
serial: 8250: Extract platform driver
serial: 8250: Extract RSA bits
serial: imx: stop casting struct uart_port to struct imx_port
...
The devicetree updates are fairly well spread out across platforms,
with Qualcomm making up about a third of the total.
There are three new SoCs in existing product families this:
- NXP i.MX95 is a variant of i.MX93, now with six Cortex-A55 cores
instead of just two as well as a GPU and more high-speed I/O
devices.
- Qualcomm QCS8550 is a variant of SM8550 for IOT devices
- Airoha EN7581 is a 10G-PON network chip and related to
the MT7981 Wireless router chip from its parent Mediatek.
In total there are 58 new machines, including four riscv
boards and eight for 32-bit arm.
The most exciting new addition is probably a pair of laptops
based on the Qualcomm x1e80100 (Snapdragon X1 Elite) chip,
the Asus Vivobook S15 and the Lenovo Yoga Slim7x.
Other noteworthy new additions are:
- A total of 20 Qualcomm based machines, mostly Android devices
from Samsung, Motorola and LG, as well as a wireless router
and some reference designs
- Six NXP i.MX based machines, mostly industrial boards along
with some reference designs
- Mediatek sees some interesting Filogic based routers
including the "OpenWRT One", a few new Chromebooks as
well as single-board computers.
- Four machines from Solidrun based on Marvell cn913x,
replacing the older Armada 8000 based counterparts
- The four Amlogic machines are all set top boxes or reference
designs for them
- The nine new Rockchips machines are mostly single-board
computers including some interesting ones based on the
rk3588 chip like the ROCK 5 ITX board and the CM3588
with its four NVMe slots
- The RISC-V boards are all single-board computers based on
Starfive JH7110, Microchip MPFS and Allwinner D1, which all
had similar boards already
There are also a lot of updates to already supported machines,
notably for the TI K3, Rockchips, Freescale and of course
Qualcomm platforms.
-----BEGIN PGP SIGNATURE-----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=xGqj
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC dt updates from Arnd Bergmann:
"The devicetree updates are fairly well spread out across platforms,
with Qualcomm making up about a third of the total.
There are three new SoCs in existing product families this:
- NXP i.MX95 is a variant of i.MX93, now with six Cortex-A55 cores
instead of just two as well as a GPU and more high-speed I/O
devices.
- Qualcomm QCS8550 is a variant of SM8550 for IOT devices
- Airoha EN7581 is a 10G-PON network chip and related to the MT7981
Wireless router chip from its parent Mediatek.
In total there are 58 new machines, including four riscv boards and
eight for 32-bit arm.
The most exciting new addition is probably a pair of laptops based on
the Qualcomm x1e80100 (Snapdragon X1 Elite) chip, the Asus Vivobook
S15 and the Lenovo Yoga Slim7x.
Other noteworthy new additions are:
- A total of 20 Qualcomm based machines, mostly Android devices from
Samsung, Motorola and LG, as well as a wireless router and some
reference designs
- Six NXP i.MX based machines, mostly industrial boards along with
some reference designs
- Mediatek sees some interesting Filogic based routers including the
"OpenWRT One", a few new Chromebooks as well as single-board
computers.
- Four machines from Solidrun based on Marvell cn913x, replacing the
older Armada 8000 based counterparts
- The four Amlogic machines are all set top boxes or reference
designs for them
- The nine new Rockchips machines are mostly single-board computers
including some interesting ones based on the rk3588 chip like the
ROCK 5 ITX board and the CM3588 with its four NVMe slots
- The RISC-V boards are all single-board computers based on Starfive
JH7110, Microchip MPFS and Allwinner D1, which all had similar
boards already
There are also a lot of updates to already supported machines, notably
for the TI K3, Rockchips, Freescale and of course Qualcomm platforms"
* tag 'soc-dt-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (846 commits)
arm64: dts: allwinner: h616: add crypto engine node
riscv: dts: add clock generator for Sophgo SG2042 SoC
arm64: dts: rockchip: Add Xunlong Orange Pi 3B
dt-bindings: arm: rockchip: Add Xunlong Orange Pi 3B
arm64: dts: rockchip: Add Radxa ROCK 3B
dt-bindings: arm: rockchip: Add Radxa ROCK 3B
mailmap: Update Luca Weiss's email address
ARM: dts: ixp4xx: nslu2: beeper uses PWM
arm64: dts: rockchip: add ROCK 5 ITX board
dt-bindings: arm: rockchip: Add ROCK 5 ITX board
arm64: dts: rockchip: Add dma-names to uart1 on Pine64 rk3566 devices
arm64: dts: rockchip: Add avdd supplies to hdmi on rock64
arm64: dts: qcom: msm8916-lg-c50: add initial dts for LG Leon LTE
arm64: dts: qcom: msm8916-lg-m216: Add initial device tree
dt-bindings: arm: qcom: Add msm8916 based LG devices
ARM: dts: qcom: msm8960: correct memory base
arm64: dts: qcom: ipq9574: Add icc provider ability to gcc
dt-bindings: interconnect: Add Qualcomm IPQ9574 support
arm64: dts: qcom: sm8150: Add video clock controller node
arm64: dts: qcom: pm6150: Add vibrator
...
Add clock generator node to device tree for SG2042, and enable clock for
uart.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
T-Head:
Last change from me before this starts going via Drew's tree is the
addition of the SBI PMU events node for the th1520.
StarFive:
A dts for the Pin64 Star64, another board with a jh7110 SoC. This board
is almost identical to the existing Milk-v Mars and VisionFive 2 boards
that are already support - just with a different PHY configuration and
only one of the two PCIe ports exposed. Additionally, the Mars and
VisionFive 2 get their PCie configuration added.
Microchip:
A dts for the BeagleV Fire. PCIe is disabled on it for now, as some
binding and driver changes are required.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCZorVOAAKCRB4tDGHoIJi
0j35AQDgZyo3BkwRVpEqGo4GXNWvOPPfiEAuQ+m8hlnDG8PteQD+LOkcfjK/Y2Bk
vj6vhJYGy/9yODRXaI756szEf6VGDg8=
=Tefh
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=tdm/
-----END PGP SIGNATURE-----
Merge tag 'riscv-dt-for-v6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetrees for v6.11
T-Head:
Last change from me before this starts going via Drew's tree is the
addition of the SBI PMU events node for the th1520.
StarFive:
A dts for the Pin64 Star64, another board with a jh7110 SoC. This board
is almost identical to the existing Milk-v Mars and VisionFive 2 boards
that are already support - just with a different PHY configuration and
only one of the two PCIe ports exposed. Additionally, the Mars and
VisionFive 2 get their PCie configuration added.
Microchip:
A dts for the BeagleV Fire. PCIe is disabled on it for now, as some
binding and driver changes are required.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: starfive: add PCIe dts configuration for JH7110
riscv: dts: microchip: add an initial devicetree for the BeagleV Fire
dt-bindings: riscv: microchip: document beaglev-fire
riscv: dts: starfive: Update flash partition layout
riscv: dts: thead: th1520: Add PMU event node
riscv: dts: starfive: add Star64 board devicetree
dt-bindings: riscv: starfive: add Star64 board compatible
dt-bindings: riscv: Add T-HEAD C908 compatible
Link: https://lore.kernel.org/r/20240707-nuttiness-lustfully-4aaf03c991b2@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This includes a commit shared with the clk tree. This commit adds clock
and reset indices to the device tree binding, and thus is needed for
both the device tree and driver changes.
ARM64 device tree and binding-only changes
- Add LRADC (low resolution ADC for resistor network based keys) for H616 SoC
- Add cache information for A64, H6, and H616 SoCs
- Correct model names and descriptions for Pine64 boards
- Add GPADC (general purpose ADC) for H616 SoC
- Add ADC joysticks based on GPADC for anbernic-rg35xx-h board
- Add additional CPU OPPs for the H700 on top of existing H616 ones
- Enable DVFS for rg35xx boards
- Add IOMMU for H616 SoC
RISC-V device tree changes
- Add system LDOs to D1s/T113 SoC
- Add ClockworkPi and DevTerm device trees
-----BEGIN PGP SIGNATURE-----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=3vmg
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmaL9/8ACgkQYKtH/8kJ
UifiHRAA0qHvjj5uaQiQnjJgOFF+Rmf3goNje2S9f35ziO2AGKqsfp651mBbZFpJ
yFkIMlELMBLmgB9cEXfvoWlvUjITxduiMjn0aNfu4czRhhk1qiqwy+CVhDHT681g
71s1crZ0gT/B9hNQkfHz6AmrvMl6k9NPHioaci4abRNXsGNrZuuSFNOAC82l8nrb
PLJZtNOEbtkVP5pdBatTlsdJywOLpl1KwYvXbbC8oXvMobywUSsW/gjcHV0hUjlp
4kwDEyi1cUGeNEuPAcp2Pp0H+WtHJsaTN1BhIy3kyCGiCXX3ShkZiaYIPwBGdUrz
NJihJ/WoU2pMzlX5OH2L2d1KybZhOPB+kzSqw2TWyZuKNc+HY3BaXeZ8uVUz59Tv
WSml2dz4+T816jDcBrK9sFC1uiJlbieKNJsH8Ol0FykJcfjD48tP7Y1uMhqN3ict
y/FZ6nvPNEf7YPGGTXDjn0d5ifXAyGXLhIWxRXBP701HAzTkUPeTEdMLwj+6H1eh
HBxFaa4yeAtH9+0c/Tf1Ge244OxbavwjJU4ufyD7X440nHqFVXQvF2FD451tBd5F
HbXZ3cm+E8/zg55L0sAcY++5W+Aa2S+TvK64nrKcGEEDonBj3WwdNL5iwtzugWCv
/AQg1UP3uQIyPvrwcyyoG8lenyHjOhZnACH3qbxpO9JnnwEIXQk=
=Emn4
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into soc/dt
Allwinner SoC device tree changes for 6.11
This includes a commit shared with the clk tree. This commit adds clock
and reset indices to the device tree binding, and thus is needed for
both the device tree and driver changes.
ARM64 device tree and binding-only changes
- Add LRADC (low resolution ADC for resistor network based keys) for H616 SoC
- Add cache information for A64, H6, and H616 SoCs
- Correct model names and descriptions for Pine64 boards
- Add GPADC (general purpose ADC) for H616 SoC
- Add ADC joysticks based on GPADC for anbernic-rg35xx-h board
- Add additional CPU OPPs for the H700 on top of existing H616 ones
- Enable DVFS for rg35xx boards
- Add IOMMU for H616 SoC
RISC-V device tree changes
- Add system LDOs to D1s/T113 SoC
- Add ClockworkPi and DevTerm device trees
* tag 'sunxi-dt-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
riscv: dts: allwinner: Add ClockworkPi and DevTerm devicetrees
riscv: dts: allwinner: d1s-t113: Add system LDOs
arm64: dts: allwinner: h616: add IOMMU node
arm64: dts: allwinner: rg35xx: Enable DVFS CPU frequency scaling
arm64: dts: allwinner: h616: add additional CPU OPPs for the H700
arm64: dts: allwinner: anbernic-rg35xx-h: Add ADC joysticks
arm64: dts: allwinner: h616: Add GPADC device node
dt-bindings: clock: sun50i-h616-ccu: Add GPADC clocks
ARM: dts: sunxi: remove duplicated entries in makefile
arm64: dts: allwinner: Add cache information to the SoC dtsi for H616
arm64: dts: allwinner: Add cache information to the SoC dtsi for A64
arm64: dts: allwinner: Correct the model names for Pine64 boards
dt-bindings: arm: sunxi: Correct the descriptions for Pine64 boards
arm64: dts: allwinner: Add cache information to the SoC dtsi for H6
ARM: dts: sun50i: Add LRADC node
dt-bindings: input: sun4i-lradc-keys: Add H616 compatible
Link: https://lore.kernel.org/r/ZoQa8r1N8yi7FlPV@wens.tw
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add PCIe dts configuraion for JH7110 SoC platform. The Star64 only has
one exposed PCIe port, so only the Mars and VisionFive 2 get two
enabled.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
[conor: squash in star64's single exposed port]
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmaB0NweHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGkvwH/36UJRk/o6wvXnyH
E6QjCSWo2226APyWks22NjtC3I/8Iqdvkneuh6wG0qL2sXAB078EMjUq5R81bF8H
wWFBJwetjYTp8GEyLioMEb2wCH/J3R29dLFC4UYTplafXRGP6//xcpJaKmTxcgdR
31IzvTPXbApZ7L3k1U6rA2bK9PNKcFCOvZlrNMUCuwMrabymHsDfOUt1DqXyg2xp
zjqiWYBwlklozmgawSWt/mdEgkWuTcAbg+KyqDVQF59s9aj/OOwZ0j+HACq5V8CM
quTPIAYL6CC9p7uxa69lGr/sgC0Is/BZLPX7RTZAwCgarGvnX+1HUsjDcaFCtrVg
O6fPUV8=
=pgUx
-----END PGP SIGNATURE-----
Merge 6.10-rc6 into tty-next
This resolves the merge issues in the 8250 code due to some reverts in
6.10-rc6 in the console changes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clockwork Tech manufactures several SoMs for their RasPi CM3-compatible
"ClockworkPi" mainboard. Their R-01 SoM features the Allwinner D1 SoC.
The R-01 contains only the CPU, DRAM, and always-on voltage regulation;
it does not merit a separate devicetree.
The ClockworkPi mainboard features analog audio, a MIPI-DSI panel, USB
host and peripheral ports, an Ampak AP6256 WiFi/Bluetooth module, and an
X-Powers AXP228 PMIC for managing a Li-ion battery.
The DevTerm is a complete system which extends the ClockworkPi mainboard
with a MIPI-DSI panel and a pair of expansion boards. These expansion
boards provide a fan, a USB keyboard, speakers, and a thermal printer.
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20240622150731.1105901-4-wens@kernel.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
T-Head:
Jisheng hasn't got enough time to look after the platform, so Drew
Fustini is going to take over.
StarFive:
A fix for a regulator voltage range that prevented using low performance
SD cards.
Canaan:
Cleanup for some "over eager" aliases for serial ports that did not
exist on some boards and I/O devices disabled on boards where they were
not actually in use.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCZnWJ7wAKCRB4tDGHoIJi
0pYNAP9f3zNfNJF+nIm10LzLnrX3U/sqYZaFlTPqpzQCpvdtTgEAvaxfN5x6zcR9
6obpBSAlYN+7OlFVEtMfUf6UYq2rwwA=
=AQmx
-----END PGP SIGNATURE-----
Merge tag 'riscv-dt-fixes-for-v6.10-rc5+' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into arm/fixes
RISC-V Devicetree fixes for v6.10-rc5+
T-Head:
Jisheng hasn't got enough time to look after the platform, so Drew
Fustini is going to take over.
StarFive:
A fix for a regulator voltage range that prevented using low performance
SD cards.
Canaan:
Cleanup for some "over eager" aliases for serial ports that did not
exist on some boards and I/O devices disabled on boards where they were
not actually in use.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add an initial devicetree for the BeagleV Fire. This devicetree differs
from that in the BeagleBoard BSP as it has a different memory
configuration, however it will boot on the same FPGA images. PCI is
disabled for now, as the Linux PCI driver (and the binding) assume
which root port instance is in use. This will need to be fixed before
PCI can be enabled.
Link: https://www.beagleboard.org/boards/beaglev-fire
Co-developed-by: Jamie Gibbons <jamie.gibbons@microchip.com>
Signed-off-by: Jamie Gibbons <jamie.gibbons@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Currently, for JH7110 boards with EMMC slot, vqmmc voltage for EMMC is
fixed to 1.8V, while the spec needs it to be 3.3V on low speed mode and
should support switching to 1.8V when using higher speed mode. Since
there are no other peripherals using the same voltage source of EMMC's
vqmmc(ALDO4) on every board currently supported by mainline kernel,
regulator-max-microvolt of ALDO4 should be set to 3.3V.
Cc: stable@vger.kernel.org
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Fixes: 7dafcfa79c ("riscv: dts: starfive: enable DCDC1&ALDO4 node in axp15060")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Up to now, the describe flash partition layout has some gaps.
Use the whole flash chip by getting rid of the gaps.
Suggested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The Pine64 Star64 is a development board based on the Starfive JH7110 SoC.
The board features:
- JH7110 SoC
- 4/8 GiB LPDDR4 DRAM
- AXP15060 PMIC
- 40 pin GPIO header
- 1x USB 3.0 host port
- 3x USB 2.0 host port
- 1x eMMC slot
- 1x MicroSD slot
- 1x QSPI Flash
- 2x 1Gbps Ethernet port
- 1x HDMI port
- 1x 4-lane DSI
- 1x 2-lane CSI
- 1x PCIe 2.0 x1 lane
Signed-off-by: Henry Bell <dmoo_dv@protonmail.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
It is considered good practice to disable on-SoC devices providing
external I/O in the SoC-specific .dtsi, and enable them explicitly in
the board-specific DTS files when actually wired-up and used.
Hence:
- Set the status of I/O devices in k210.dtsi to "disabled",
- Override the status of used I/O devices in board-specific DTS files
to "okay",
- Drop unneeded status overrides in board DTS-specific files for the
always-enabled pin controller.
On e.g. MAiXBiT, this gets rid of an error message when probing the
unused slave-only spi2 controller:
dw_spi_mmio 50240000.spi: error -22: problem registering spi host
dw_spi_mmio 50240000.spi: probe with driver dw_spi_mmio failed with error -22
which is seen since commit 98d75b9ef2 ("spi: dw: Drop default
number of CS setting").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The SoC-specific k210.dtsi declares aliases for all four serial ports.
However, none of the board-specific DTS files configure pin control for
any but the first serial port, so the last three ports are not usable.
Move the aliases node from the SoC-specific k210.dtsi to the
board-specific DTS files, as these are really board-specific, and retain
the sole port that is usable.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
This is a follow-up to an earlier pull request for device tree changes,
as three platform maintainers sent their contents too late to be included
in the main set, but had not caused any further problems since then:
- The Amlogic platform now containts support for two new SoC types,
the A4 and A5 chips for audio applications. Both come with a
reference board, and one more dts file gets addded for the
combination of the MNT Reform Laptop with the BPI-CM4 CPU
module
- The ASpeed platform adds support for six addititional server
platforms that use ast2500 or ast2600 as their BMC, while
another one gets removed.
- The RISC-V platforms from Microchip, Starfive and and T-HEAD
get additional features for existing hardware, plus the
addition of the Milk-V Mars based on the StarFive VisionFive v2
board.
-----BEGIN PGP SIGNATURE-----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=iChs
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-late-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull more SoC devicetree updates from Arnd Bergmann:
"This is a follow-up to an earlier pull request for device tree
changes, as three platform maintainers sent their contents too late to
be included in the main set, but had not caused any further problems
since then:
- The Amlogic platform now containts support for two new SoC types,
the A4 and A5 chips for audio applications. Both come with a
reference board, and one more dts file gets addded for the
combination of the MNT Reform Laptop with the BPI-CM4 CPU module
- The ASpeed platform adds support for six addititional server
platforms that use ast2500 or ast2600 as their BMC, while another
one gets removed
- The RISC-V platforms from Microchip, Starfive and and T-HEAD get
additional features for existing hardware, plus the addition of the
Milk-V Mars based on the StarFive VisionFive v2 board"
* tag 'soc-dt-late-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (76 commits)
riscv: dts: microchip: add pac1934 power-monitor to icicle
riscv: dts: thead: Fix node ordering in TH1520 device tree
ARM: dts: aspeed: Add ASRock E3C256D4I BMC
dt-bindings: arm: aspeed: document ASRock E3C256D4I
dt-bindings: trivial-devices: add isil,isl69269
ARM: dts: aspeed: x4tf: Add dts for asus x4tf project
dt-bindings: arm: aspeed: add ASUS X4TF board
ARM: dts: aspeed: Remove Facebook Cloudripper dts
ARM: dts: aspeed: drop unused ref_voltage ADC property
ARM: dts: aspeed: harma: correct Mellanox multi-host property
ARM: dts: aspeed: yosemitev2: correct Mellanox multi-host property
ARM: dts: aspeed: yosemite4: correct Mellanox multi-host property
ARM: dts: aspeed: greatlakes: correct Mellanox multi-host property
ARM: dts: aspeed: Modify I2C bus configuration
ARM: dts: aspeed: Disable unused ADC channels for Asrock X570D4U BMC
ARM: dts: aspeed: Modify GPIO table for Asrock X570D4U BMC
ARM: dts: aspeed: yosemite4: set bus13 frequency to 100k
ARM: dts: Aspeed: Bonnell: Fix NVMe LED labels
ARM: dts: aspeed: yosemite4: Enable ipmb device for OCP debug card
ARM: dts: aspeed: ahe50dc: Update lm25066 regulator name
...
The binding for this landed in v6.9, add the description. In the
off-chance that there were people carrying local patches for this based
on the driver shipped on the Microchip website (or vendor kernel) both
the binding and sysfs filenames changed during upstreaming.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The Milkv Mars is a development board based on the Starfive JH7110 SoC.
The board features:
- JH7110 SoC
- 1/2/4/8 GiB LPDDR4 DRAM
- AXP15060 PMIC
- 40 pin GPIO header
- 3x USB 3.0 host port
- 1x USB 2.0 host port
- 1x M.2 E-Key
- 1x eMMC slot
- 1x MicroSD slot
- 1x QSPI Flash
- 1x 1Gbps Ethernet port
- 1x HDMI port
- 1x 2-lane DSI and 1x 4-lane DSI
- 1x 2-lane CSI
I fixed up some nits Emil pointed out. This merges fixes into for-next
to avoid messing around with some nodes that were removed as fixes this
cycle.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
According to the device tree coding style, nodes shall be ordered by
unit address in ascending order.
Signed-off-by: Thomas Bonnefille <thomas.bonnefille@bootlin.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Sophgo:
Added sdhci support for cv18xx/duo.
Added clock support for cv18xx.
Added clock for uart/sdhci.
Added spi support for cv18xx.
Added i2c support for cv18xx.
Added reserved memory node for cv1800b/duo.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
-----BEGIN PGP SIGNATURE-----
iQGzBAABCgAdFiEEyXBewyFOIoMq4pDN7RKLaY1m8IIFAmYxmBsACgkQ7RKLaY1m
8IKJbwwA2MF4SGcM7ZBdrYrom0leEIv7/UrGyGLOK3GUY57hp2upsrpE9j66x8sV
5GGEdlUoAzlcHFe23FzA44JVhRm3NcgUo5CAZRrjrk9M17RKdCWziiJ5h4ZbP1Ue
a787yAAg58OmMLSpaJBoO0IwjFiUS8nUC9YUSqvWmVhtsvHO/n7aZKvYOdgZ3lnA
LtlQGpsuz3q8q5Gk/tmS8astIkxzCMVlLfipkETqF5H5dtlw/tl7sIqubxUnnWea
/qj6QiSn+li2jdk4VQOw57Fc6IEkFZtYJGRwnCKmZE7thHA2z8HZ+gIXDq/X0CU8
PTnwQ7nO0oRJn0bQLACy+vO/9iznRNo+y3HAoVQtDjB/Xef6JbIrI/1pnft8UUQO
ZBGvuvXbq7K1uTpVHIrup9AnxwcNTzNFJ6wK/jap/R+CAIZKA2GSpNgd0qDOxzGh
OLjTVnU1jc7VhB2gaNEaox9zs0s6MOxMwz9iRLAA3Dsyitbx1AEjq63vYXE3KR72
dnvT4Y8j
=d7SS
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmYzjYsACgkQYKtH/8kJ
Uie5nA//Sib+nyw4b/v6Mk1c+OWl+N+V9iaennHJ3hcRxC/AQDF6RbwPi3DVItkz
KvXFGa7buTl1HzmiBVqjv1k2lZTFdZo6ZndwGwr/V1qd9pP+USoC/5ua4XatYdP+
UT9RtXnqTMRzYFXVYnYKzs3phhteGfqg8yAmqOqNN6mtkgzy0Wi3NGoPWVD83G2V
PZY0LcC3H9qU0lM3KXicHGWAPWgrvOo9iVdeXNlKt0QKvaMRw0t3tkKQSb2HEBvv
M2T6uknTir8lFdXhC/6r26zNiC0Iuk9/xtVuTvyI1NWyscLy+F0orR7QT49axEBO
C425MQ34OkyPfplGvROWq9PN4jpnbyMIlFnP0/VJyjPfO6oZ7MYNJ6hbYjrNDf/7
n/8RugMxtUZVwBHTb5pKvCgB51/zf80N5bNVW1yRQ3HbUFz91VaPTh5m+WKFz7BQ
6rETCpdS4ai0tkREbfbNPhBmid3SuqF9wTWEOcfh2BqRCjc+c4In/XsVFkDLGxL/
peZku7C11hTDc3L/WazU2hwwjye28aoqykhr6B7CQ7MiThkUnknXrXkdfqwiTDJj
Dv4e2wl0LU3zN66NFTlpUQ4fYXTD6IH8d3ps9qLaY3KbALbMR8x+oTnwBfxYUJuL
oP/NT6kEFCRP1pdU9E4OXhvaqvfGQI4/gETnefXmsG68u0dtS24=
=5D+b
-----END PGP SIGNATURE-----
Merge tag 'riscv-sophgo-dt-for-v6.10' of https://github.com/sophgo/linux into soc/dt
RISC-V Devicetrees for v6.10
Sophgo:
Added sdhci support for cv18xx/duo.
Added clock support for cv18xx.
Added clock for uart/sdhci.
Added spi support for cv18xx.
Added i2c support for cv18xx.
Added reserved memory node for cv1800b/duo.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
* tag 'riscv-sophgo-dt-for-v6.10' of https://github.com/sophgo/linux:
riscv: dts: sophgo: add reserved memory node for CV1800B
riscv: dts: sophgo: use real clock for sdhci
riscv: dts: sophgo: cv18xx: Add i2c devices
riscv: dts: sophgo: cv18xx: Add spi devices
riscv: dts: sophgo: add uart clock for Sophgo CV1800 series SoC
riscv: dts: sophgo: add clock generator for Sophgo CV1800 series SoC
riscv: dts: sophgo: add sdcard support for milkv duo
Link: https://lore.kernel.org/r/MA0P287MB2822CA2DE757787D6EA3B1F8FE192@MA0P287MB2822.INDP287.PROD.OUTLOOK.COM
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is to prepare for Milkv Mars board dts support in the following
patch. Let's factored out common part into .dtsi.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
No physical write-protect line is present, so setting "disable-wp".
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Per VisionFive 2 1.2B, and 1.3A boards' SCH, GPIO 41 is used as
card detect. So add "cd-gpios" property for this.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
As pointed out by Krzysztof "Board should not bring new CPU nodes.
Override by label instead."
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Use "audio-codec" as the codec dt node name, and "sound" as the simple
audio card dt name.
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add the 'cpus' label so that we can reference it in board dts files.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Now that we have enabled IRQC support for RZ/Five SoC switch to interrupt
mode for ethernet0/1 PHYs instead of polling mode.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240403203503.634465-6-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This partially reverts
commit 92cfc35838 ("riscv: dts: starfive: Add the nodes and pins of I2Srx/I2Stx0/I2Stx1")
This added device tree nodes for I2S hardware that is not actually on the
VisionFive 2 board, but connected on the 40pin header. Many different extension
boards could be added on those pins, so this should be handled by overlays
instead.
This also conflicts with the TDM node which also attempts to grab GPIO 44:
starfive-jh7110-sys-pinctrl 13040000.pinctrl: pin GPIO44 already requested by 10090000.tdm; cannot claim for 120c0000.i2s
Fixes: 92cfc35838 ("riscv: dts: starfive: Add the nodes and pins of I2Srx/I2Stx0/I2Stx1")
Signed-off-by: Hannah Peuckmann <hannah.peuckmann@canonical.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
This partially reverts
commit e7c304c034 ("riscv: dts: starfive: jh7110: add the node and pins configuration for tdm")
This added device tree nodes for TDM hardware that is not actually on the
VisionFive 2 board, but connected on the 40pin header. Many different extension
boards could be added on those pins, so this should be handled by overlays
instead.
This also conflicts with the I2S node which also attempts to grab GPIO 44:
starfive-jh7110-sys-pinctrl 13040000.pinctrl: pin GPIO44 already requested by 10090000.tdm; cannot claim for 120c0000.i2s
Fixes: e7c304c034 ("riscv: dts: starfive: jh7110: add the node and pins configuration for tdm")
Signed-off-by: Hannah Peuckmann <hannah.peuckmann@canonical.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Interrupt line number of the AXP15060 PMIC is not a necessary part of
its device tree. Originally the binding required one, so the dts patch
added an invalid interrupt that the driver ignored (0) as the interrupt
line of the PMIC is not actually connected on this platform. This went
unnoticed during review as it would have been a valid interrupt for a
GPIO controller, but it is not for the PLIC. The PLIC, on this platform
at least, silently ignores the enablement of interrupt 0. Bo Gan is
running a modified version of OpenSBI that faults if writes are done to
reserved fields, so their kernel runs into problems.
Delete the invalid interrupt from the device tree.
Cc: stable@vger.kernel.org
Reported-by: Bo Gan <ganboing@gmail.com>
Link: https://lore.kernel.org/all/c8b6e960-2459-130f-e4e4-7c9c2ebaa6d3@gmail.com/
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Fixes: 2378341504 ("riscv: dts: starfive: Enable axp15060 pmic for cpufreq")
[conor: rewrite the commit message to add more detail]
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* Support for various vector-accelerated crypto routines.
* Hibernation is now enabled for portable kernel builds.
* mmap_rnd_bits_max is larger on systems with larger VAs.
* Support for fast GUP.
* Support for membarrier-based instruction cache synchronization.
* Support for the Andes hart-level interrupt controller and PMU.
* Some cleanups around unaligned access speed probing and Kconfig
settings.
* Support for ACPI LPI and CPPC.
* Various cleanus related to barriers.
* A handful of fixes.
-----BEGIN PGP SIGNATURE-----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=3dL5
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-6.9-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
- Support for various vector-accelerated crypto routines
- Hibernation is now enabled for portable kernel builds
- mmap_rnd_bits_max is larger on systems with larger VAs
- Support for fast GUP
- Support for membarrier-based instruction cache synchronization
- Support for the Andes hart-level interrupt controller and PMU
- Some cleanups around unaligned access speed probing and Kconfig
settings
- Support for ACPI LPI and CPPC
- Various cleanus related to barriers
- A handful of fixes
* tag 'riscv-for-linus-6.9-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (66 commits)
riscv: Fix syscall wrapper for >word-size arguments
crypto: riscv - add vector crypto accelerated AES-CBC-CTS
crypto: riscv - parallelize AES-CBC decryption
riscv: Only flush the mm icache when setting an exec pte
riscv: Use kcalloc() instead of kzalloc()
riscv/barrier: Add missing space after ','
riscv/barrier: Consolidate fence definitions
riscv/barrier: Define RISCV_FULL_BARRIER
riscv/barrier: Define __{mb,rmb,wmb}
RISC-V: defconfig: Enable CONFIG_ACPI_CPPC_CPUFREQ
cpufreq: Move CPPC configs to common Kconfig and add RISC-V
ACPI: RISC-V: Add CPPC driver
ACPI: Enable ACPI_PROCESSOR for RISC-V
ACPI: RISC-V: Add LPI driver
cpuidle: RISC-V: Move few functions to arch/riscv
riscv: Introduce set_compat_task() in asm/compat.h
riscv: Introduce is_compat_thread() into compat.h
riscv: add compile-time test into is_compat_task()
riscv: Replace direct thread flag check with is_compat_task()
riscv: Improve arch_get_mmap_end() macro
...
These are changes that for some reason ended up not making it into the
first four branches but that should still make it into 6.9:
- A rework of the omap clock support that touches both drivers and
device tree files
- The reset controller branch changes that had a dependency on late
bugfixes. Merging them here avoids a backmerge of 6.8-rc5 into the
drivers branch
- The RISC-V/starfive, RISC-V/microchip and ARM/Broadcom devicetree
changes that got delayed and needed some extra time in linux-next
for wider testing.
-----BEGIN PGP SIGNATURE-----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=IzoE
-----END PGP SIGNATURE-----
Merge tag 'soc-late-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull more ARM SoC updates from Arnd Bergmann:
"These are changes that for some reason ended up not making it into the
first four branches but that should still make it into 6.9:
- A rework of the omap clock support that touches both drivers and
device tree files
- The reset controller branch changes that had a dependency on late
bugfixes. Merging them here avoids a backmerge of 6.8-rc5 into the
drivers branch
- The RISC-V/starfive, RISC-V/microchip and ARM/Broadcom devicetree
changes that got delayed and needed some extra time in linux-next
for wider testing"
* tag 'soc-late-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (31 commits)
soc: fsl: dpio: fix kcalloc() argument order
bus: ts-nbus: Improve error reporting
bus: ts-nbus: Convert to atomic pwm API
riscv: dts: starfive: jh7110: Add camera subsystem nodes
ARM: bcm: stop selecing CONFIG_TICK_ONESHOT
ARM: dts: omap3: Update clksel clocks to use reg instead of ti,bit-shift
ARM: dts: am3: Update clksel clocks to use reg instead of ti,bit-shift
clk: ti: Improve clksel clock bit parsing for reg property
clk: ti: Handle possible address in the node name
dt-bindings: pwm: opencores: Add compatible for StarFive JH8100
dt-bindings: riscv: cpus: reg matches hart ID
reset: Instantiate reset GPIO controller for shared reset-gpios
reset: gpio: Add GPIO-based reset controller
cpufreq: do not open-code of_phandle_args_equal()
of: Add of_phandle_args_equal() helper
reset: simple: add support for Sophgo SG2042
dt-bindings: reset: sophgo: support SG2042
riscv: dts: microchip: add specific compatible for mpfs pdma
riscv: dts: microchip: add missing CAN bus clocks
ARM: brcmstb: Add debug UART entry for 74165
...
No core changes this time around.
New drivers:
- New driver for Renesas R8A779H0 also known as R-Car V4M.
- New driver for the Awinic AW9523/B I2C GPIO expander.
I found this living out-of-tree in OpenWrt as an upstream
attempt had stalled on the finishing line, so I picked it
up and finished the job.
Improvements:
- The Nomadik pin control driver was for years re-used out of
tree for the ST STA chips, and now the IP was re-used in a
MIPS automotive SoC called MobilEyeq5, so it has been split
in pin control and GPIO drivers so the latter can be reused
by MobilEyeq5. (Along with a long list of cleanups.)
- A lot of overall cleanup and tidying up.
-----BEGIN PGP SIGNATURE-----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=Pt9Y
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"No core changes this time around.
New drivers:
- New driver for Renesas R8A779H0 also known as R-Car V4M.
- New driver for the Awinic AW9523/B I2C GPIO expander. I found this
living out-of-tree in OpenWrt as an upstream attempt had stalled on
the finishing line, so I picked it up and finished the job.
Improvements:
- The Nomadik pin control driver was for years re-used out of tree
for the ST STA chips, and now the IP was re-used in a MIPS
automotive SoC called MobilEyeq5, so it has been split in pin
control and GPIO drivers so the latter can be reused by MobilEyeq5.
(Along with a long list of cleanups)
- A lot of overall cleanup and tidying up"
* tag 'pinctrl-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (87 commits)
drivers/gpio/nomadik: move dummy nmk_gpio_dbg_show_one() to header
gpio: nomadik: remove BUG_ON() in nmk_gpio_populate_chip()
dt-bindings: pinctrl: qcom: update compatible name for match with driver
pinctrl: aw9523: Make the driver tristate
pinctrl: nomadik: fix dereference of error pointer
gpio: nomadik: Back out some managed resources
pinctrl: aw9523: Add proper terminator
pinctrl: core: comment that pinctrl_add_gpio_range() is deprecated
pinctrl: pinmux: Suppress error message for -EPROBE_DEFER
pinctrl: Add driver for Awinic AW9523/B I2C GPIO Expander
dt-bindings: pinctrl: Add bindings for Awinic AW9523/AW9523B
gpio: nomadik: Finish conversion to use firmware node APIs
gpio: nomadik: fix Kconfig dependencies inbetween pinctrl & GPIO
pinctrl: da9062: Add OF table
dt-bindings: pinctrl: at91: add sam9x7
pinctrl: ocelot: remove redundant assignment to variable ret
gpio: nomadik: grab optional reset control and deassert it at probe
gpio: nomadik: support mobileye,eyeq5-gpio
gpio: nomadik: handle variadic GPIO count
gpio: nomadik: support shared GPIO IRQs
...
xandespmu stands for Andes Performance Monitor Unit extension.
Based on the added Andes PMU ISA string, the SBI PMU driver
will make use of the non-standard irq source.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240222083946.3977135-10-peterlin@andestech.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Starfive:
The previous cleanup broke boot on the jh7100 as the driver depended on
the fallback clock name created based on the node-name when
clock-output-names is not present. Add clock-output-names to restore
working order.
Generic:
BUILTIN_DTB has been broken for ages on any platform other than the
nommu Canaan k210 SoC as the first dtb built (in alphanumerical order),
would get built into the image. This didn't get fixed for ages because
nobody actually cared about running it other than the k210 enough to
fix it. The folks doing Sophgo SG2042 development have come along and
fixed it, as they want to use builtin dtbs. linux-boot on that platform
reuses the dtb it was provided by OpenSBI when booting linux proper,
which is unfortunately not possible to boot a mainline kernel with.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCZeiwSAAKCRB4tDGHoIJi
0i35AP9Nm72QRsmcW1EaICAQDkfPyPVdpHp1WkHIDyNHcjPkrgEAtPy4Mlz9LIhx
pQ5QuXV2mqkjE+Ts5k0efkL1Am8MZgs=
=zUP6
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=Ad6q
-----END PGP SIGNATURE-----
Merge tag 'riscv-dt-fixes-for-v6.8-final' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetree fixes for v6.8-final
Starfive:
The previous cleanup broke boot on the jh7100 as the driver depended on
the fallback clock name created based on the node-name when
clock-output-names is not present. Add clock-output-names to restore
working order.
Generic:
BUILTIN_DTB has been broken for ages on any platform other than the
nommu Canaan k210 SoC as the first dtb built (in alphanumerical order),
would get built into the image. This didn't get fixed for ages because
nobody actually cared about running it other than the k210 enough to
fix it. The folks doing Sophgo SG2042 development have come along and
fixed it, as they want to use builtin dtbs. linux-boot on that platform
reuses the dtb it was provided by OpenSBI when booting linux proper,
which is unfortunately not possible to boot a mainline kernel with.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-fixes-for-v6.8-final' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: Move BUILTIN_DTB_SOURCE to common Kconfig
riscv: dts: starfive: jh7100: fix root clock names
Link: https://lore.kernel.org/r/20240306-waltz-facial-9e4e1b792053@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Microchip:
Missing bus clocks for the CAN controllers spotted during the creation
of a driver for the controllers and a specific compatible for the SiFive
PDMA block on PolarFire SoC.
Starfive:
PWM nodes for the jh7100 and jh7110. Camera subsystem support for the
latter. Most notably however is the addition of ethernet support for the
jh7110 which finally allows people to use the network on the OG VisionFive
and on the Beagle-V Starlight board. This was made possible by the
non-standard cache management operations support added for the RZ/Five
which could be extended to the ccache present on the jh7100.
bindings:
Additional clarification for what the reg property represents for cpus
and two opencores PWM binding changes - the original addition and an
added compatible. The latter is here as the driver patch was not ready
but the PWM maintainer told me to go ahead and merge it.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCZed3VgAKCRB4tDGHoIJi
0rfBAP9n6/i9bitGfqZHXKc1CpqwIWb8sw28OC4u6UWaNEzSmQEA0R0bagMcfVDi
szpu4+58Bk4hbd/6lOwacdskEUp0bwU=
=gBjh
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=0UyT
-----END PGP SIGNATURE-----
Merge tag 'riscv-dt-for-v6.9' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/late
RISC-V Devicetrees for v6.9
Microchip:
Missing bus clocks for the CAN controllers spotted during the creation
of a driver for the controllers and a specific compatible for the SiFive
PDMA block on PolarFire SoC.
Starfive:
PWM nodes for the jh7100 and jh7110. Camera subsystem support for the
latter. Most notably however is the addition of ethernet support for the
jh7110 which finally allows people to use the network on the OG VisionFive
and on the Beagle-V Starlight board. This was made possible by the
non-standard cache management operations support added for the RZ/Five
which could be extended to the ccache present on the jh7100.
bindings:
Additional clarification for what the reg property represents for cpus
and two opencores PWM binding changes - the original addition and an
added compatible. The latter is here as the driver patch was not ready
but the PWM maintainer told me to go ahead and merge it.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.9' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: starfive: jh7110: Add camera subsystem nodes
dt-bindings: pwm: opencores: Add compatible for StarFive JH8100
dt-bindings: riscv: cpus: reg matches hart ID
riscv: dts: microchip: add specific compatible for mpfs pdma
riscv: dts: microchip: add missing CAN bus clocks
riscv: dts: starfive: beaglev-starlight: Setup phy reset gpio
riscv: dts: starfive: visionfive-v1: Setup ethernet phy
riscv: dts: starfive: jh7100-common: Setup pinmux and enable gmac
riscv: dts: starfive: jh7100: Add sysmain and gmac DT nodes
riscv: dts: starfive: jh7110: Add PWM node and pins configuration
riscv: dts: starfive: jh7100: Add PWM node and pins configuration
dt-bindings: pwm: Add bindings for OpenCores PWM Controller
Link: https://lore.kernel.org/r/20240305-iodine-moneywise-53797ae9bf6e@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The BUILTIN_DTB_SOURCE was only configured for K210 before. Since
SOC_BUILTIN_DTB_DECLARE was removed at commit d5805af9fe ("riscv: Fix
builtin DTB handling") from patch [1], the kernel cannot choose one of the
dtbs from then on and always take the first one dtb to use. Then, another
commit 0ddd7eaffa ("riscv: Fix BUILTIN_DTB for sifive and microchip soc")
from patch [2] supports BUILTIN_DTB_SOURCE for other SoCs. However, this
feature will only work if the Kconfig we use links the dtb we expected in
the first place as mentioned in the thread [3]. Thus, a config
BUILTIN_DTB_SOURCE is needed for all SoCs to choose one dtb to use.
For some considerations, this patch also removes default y if XIP_KERNEL
for BUILTIN_DTB, as this requires setting a proper dtb to use on the
BUILTIN_DTB_SOURCE, else the kernel with XIP but does not set
BUILTIN_DTB_SOURCE or unselect BUILTIN_DTB will not boot.
Also, this patch removes the default dtb string for k210 from Kconfig to
nommu_k210_defconfig and nommu_k210_sdcard_defconfig to avoid complex
Kconfig settings for other SoCs in the future.
[1] https://lore.kernel.org/linux-riscv/20201208073355.40828-5-damien.lemoal@wdc.com/
[2] https://lore.kernel.org/linux-riscv/20210604120639.1447869-1-alex@ghiti.fr/
[3] https://lore.kernel.org/linux-riscv/CAK7LNATt_56mO2Le4v4EnPnAfd3gC8S_Sm5-GCsfa=qXy=8Lrg@mail.gmail.com/
Signed-off-by: Yangyu Chen <cyy@cyyself.name>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add camera subsystem nodes for the StarFive JH7110 SoC. They contain the
dphy-rx, csi2rx, camss nodes.
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Two fixes for W=2 issues in devicetrees, which should constitute fixes
for all reasonable-to-fix W=2 problems on RISC-V. The others are caused
by standard USB and MMC property names containing underscores that are
not likely to ever change.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCZdYqJwAKCRB4tDGHoIJi
0tuZAQCozsk1bZtlW00MzSLcM/dGBaxkfxoYFmjsVgk6z/QyzQEAyPcLrkhvifIt
N9Cb6fG9/gJGZqaaTa+kA70rh8JjQAo=
=iaoh
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=CyGI
-----END PGP SIGNATURE-----
Merge tag 'riscv-dt-fixes-for-v6.8-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into arm/fixes
RISC-V Devicetree fixes for v6.8-rc6
Two fixes for W=2 issues in devicetrees, which should constitute fixes
for all reasonable-to-fix W=2 problems on RISC-V. The others are caused
by standard USB and MMC property names containing underscores that are
not likely to ever change.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-fixes-for-v6.8-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: sifive: add missing #interrupt-cells to pmic
riscv: dts: starfive: replace underscores in node names
Link: https://lore.kernel.org/r/20240221-foil-glade-09dbf1aa3fe2@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
At W=2 dtc complains:
hifive-unmatched-a00.dts:120.10-238.4: Warning (interrupt_provider): /soc/i2c@10030000/pmic@58: Missing '#interrupt-cells' in interrupt provider
Add the missing property.
Reviewed-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Underscores should not be used in node names (dtc with W=2 warns about
them), so replace them with hyphens.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The CAN controller on PolarFire SoC has an AHB peripheral clock _and_ a
CAN bus clock. The bus clock was omitted when the binding was written,
but is required for operation. Make up for lost time and add to the DT.
Fixes: 38a71fc048 ("riscv: dts: microchip: add mpfs's CAN controllers")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add the missing port pins P19 to P28 for RZ/Five SoC. These additional
pins provide expanded capabilities and are exclusive to the RZ/Five SoC.
Couple of port pins have different configuration and are not identical for
the complete port so introduce struct rzg2l_variable_pin_cfg to handle
such cases and introduce the PIN_CFG_VARIABLE macro. The actual pin config
is then assigned in rzg2l_pinctrl_get_variable_pin_cfg().
Add an additional check in rzg2l_gpio_get_gpioint() to only allow GPIO pins
which support interrupt facility.
While at define RZG2L_GPIO_PORT_PACK() using RZG2L_GPIO_PORT_SPARSE_PACK().
Update the gpio-ranges property in the RZ/Five SoC DTSI, as it must
match the driver.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240129135556.63466-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Link: https://lore.kernel.org/r/20240129135556.63466-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The BeagleV Starlight SBC uses a Microchip KSZ9031RNXCA PHY supporting
RGMII-ID which doesn't require any particular setup, other than defining
a reset gpio, as opposed to VisionFive V1 for which the RX internal
delay had to be adjusted.
Co-developed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The StarFive VisionFive V1 SBC uses a Motorcomm YT8521 PHY supporting
RGMII-ID, but requires manual adjustment of the RX internal delay to
work properly.
The default RX delay provided by the driver is 1.95 ns, which proves to
be too high. Applying a 50% reduction seems to mitigate the issue.
Also note this adjustment is not necessary on BeagleV Starlight SBC,
which uses a Microchip PHY. Hence, there is no indication of a
misbehaviour on the GMAC side, but most likely the issue stems from
the Motorcomm PHY.
While at it, drop the redundant gpio include, which is already provided
by jh7100-common.dtsi.
Co-developed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add pinmux configuration for DWMAC found on the JH7100 based boards and
enable the related DT node, providing a basic PHY configuration.
Co-developed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Provide the sysmain and gmac DT nodes supporting the DWMAC found on the
StarFive JH7100 SoC.
Co-developed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Change the timer layout in the dtb to fit the format that needed by
the SBI.
Fixes: 967a94a92a ("riscv: dts: add initial Sophgo SG2042 SoC device tree")
Reviewed-by: Chen Wang <unicorn_wang@outlook.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is one new SoC for each 32-bit Arm and 64-bit RISC-V, but both
the Rockchips rv1109 and Sopgho CV1812H are just minor variations of
already supported chips.
The other six new SoCs are all part of existing arm64 families, but
are somewhat more interesting:
- Samsung ExynosAutov920 is an automotive chip, and the first one
we support based on the Cortex-A78AE core with lockstep mode.
- Google gs101 (Tensor G1) is the chip used in a number of Pixel phones,
and is grouped with Samsung Exynos here since it is based on the same
SoC design, sharing most of its IP blocks with that series.
- MediaTek MT8188 is a new chip used for mid-range tablets and Chromebooks,
using two Cortex-A78 cores where the older MT8195 had four of them.
- Qualcomm SM8650 (Snapdragon 8 Gen 3) is their current top range
phone SoC and the first supported chip based on Cortex-X4, Cortex-A720
and Cortex-A520.
- Qualcomm X1E80100 (Snapdragon X Elite) in turn is the latest
Laptop chip using the custom Oryon cores.
- Unisoc UMS9620 (Tanggula 7 series) is a 5G phone SoC based on
Cortex-A76 and Cortex-A55
In terms of boards, we have
- Five old Microsoft Lumia phones, the HTC One Mini 2, Motorola Moto
G 4G, and Huawei Honor 5X/GR5, all based on Snapdragon SoCs.
- Multiple Rockchips mobile gaming systems (Anbernic RG351V,
Powkiddy RK2023, Powkiddy X55) along with the Sonoff iHost Smart
Home Hub and a few Rockchips SBCs
- Some ComXpress boards based on Marvell CN913x, which is the
follow-up to Armada 7xxx/8xxx.
- Six new industrial/embedded boards based on NXP i.MX8 and i.MX9
- Mediatek MT8183 based Chromebooks from Lenovo, Asus and Acer.
- Toradex Verdin AM62 Mallow carrier for TI AM62
- Huashan Pi board based on the SophGo CV1812H RISC-V chip
- Two boards based on Allwinner H616/H618
- A number of reference boards for various added SoCs from Qualcomm,
Mediatek, Google, Samsung, NXP and Spreadtrum
As usual, there are cleanups and warning fixes across all platforms as
well as added features for several of them.
-----BEGIN PGP SIGNATURE-----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=zR3G
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC DT updates from Arnd Bergmann:
"There is one new SoC for each 32-bit Arm and 64-bit RISC-V, but both
the Rockchips rv1109 and Sopgho CV1812H are just minor variations of
already supported chips.
The other six new SoCs are all part of existing arm64 families, but
are somewhat more interesting:
- Samsung ExynosAutov920 is an automotive chip, and the first one we
support based on the Cortex-A78AE core with lockstep mode.
- Google gs101 (Tensor G1) is the chip used in a number of Pixel
phones, and is grouped with Samsung Exynos here since it is based
on the same SoC design, sharing most of its IP blocks with that
series.
- MediaTek MT8188 is a new chip used for mid-range tablets and
Chromebooks, using two Cortex-A78 cores where the older MT8195 had
four of them.
- Qualcomm SM8650 (Snapdragon 8 Gen 3) is their current top range
phone SoC and the first supported chip based on Cortex-X4,
Cortex-A720 and Cortex-A520.
- Qualcomm X1E80100 (Snapdragon X Elite) in turn is the latest Laptop
chip using the custom Oryon cores.
- Unisoc UMS9620 (Tanggula 7 series) is a 5G phone SoC based on
Cortex-A76 and Cortex-A55
In terms of boards, we have
- Five old Microsoft Lumia phones, the HTC One Mini 2, Motorola Moto
G 4G, and Huawei Honor 5X/GR5, all based on Snapdragon SoCs.
- Multiple Rockchips mobile gaming systems (Anbernic RG351V, Powkiddy
RK2023, Powkiddy X55) along with the Sonoff iHost Smart Home Hub
and a few Rockchips SBCs
- Some ComXpress boards based on Marvell CN913x, which is the
follow-up to Armada 7xxx/8xxx.
- Six new industrial/embedded boards based on NXP i.MX8 and i.MX9
- Mediatek MT8183 based Chromebooks from Lenovo, Asus and Acer.
- Toradex Verdin AM62 Mallow carrier for TI AM62
- Huashan Pi board based on the SophGo CV1812H RISC-V chip
- Two boards based on Allwinner H616/H618
- A number of reference boards for various added SoCs from Qualcomm,
Mediatek, Google, Samsung, NXP and Spreadtrum
As usual, there are cleanups and warning fixes across all platforms as
well as added features for several of them"
* tag 'soc-dt-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (857 commits)
ARM: dts: usr8200: Fix phy registers
arm64: dts: intel: minor whitespace cleanup around '='
arm64: dts: socfpga: agilex: drop redundant status
arm64: dts: socfpga: agilex: add unit address to soc node
arm64: dts: socfpga: agilex: move firmware out of soc node
arm64: dts: socfpga: agilex: move FPGA region out of soc node
arm64: dts: socfpga: agilex: align pin-controller name with bindings
arm64: dts: socfpga: stratix10_swvp: drop unsupported DW MSHC properties
arm64: dts: socfpga: stratix10_socdk: align NAND chip name with bindings
arm64: dts: socfpga: stratix10: add unit address to soc node
arm64: dts: socfpga: stratix10: move firmware out of soc node
arm64: dts: socfpga: stratix10: move FPGA region out of soc node
arm64: dts: socfpga: stratix10: align pincfg nodes with bindings
arm64: dts: socfpga: stratix10: add clock-names to DWC2 USB
arm64: dts: socfpga: drop unsupported cdns,page-size and cdns,block-size
ARM: dts: socfpga: align NAND controller name with bindings
ARM: dts: socfpga: drop unsupported cdns,page-size and cdns,block-size
arm64: dts: rockchip: Fix led pinctrl of lubancat 1
arm64: dts: rockchip: correct gpio_pwrctrl1 typo on nanopc-t6
arm64: dts: rockchip: correct gpio_pwrctrl1 typo on rock-5b
...
StarFive:
Key peripheral support for the jh7100 that depended on the non-standard
non-coherent DMA operations, namely mmc, sdcard and sdio wifi. This
platform has long been supported out of tree by Emil and Ubuntu etc ship
images for it, so having mainline support for a wider range of
peripherals (at last) is great.
Microchip:
The flash used by Auto Update support and the corresponding QSPI
controller are added. On publicly available Icicle kits this flash is
not usable (engineering sample silicon issues) but in the future Icicle
kits will be available that have production silicon.
T-Head:
Jisheng is busy with RL this cycle and hence T-Head appears here. The
Lichee Pi and BeagleV both grow eMMC and uSD support.
Sopgho:
Support for the Huashan Pi and the cv1812h SoC it uses. The cv1812h is
almost identical to the existing cv1800b SoC. These SoCs are intended
for use in IP camera type systems but also appear on SBCs, with the last
digit denoting the amount integrated DDR3 the device has. The difference
between the cv1812h and the existing cv180x devices appears to be the
addition of video output interfaces.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCZYQ7CwAKCRB4tDGHoIJi
0p2WAQD/Hid4EDlERk34GVMj5oaIaHab9BFVdfLV9nwc9q+3sAEAo9qjd4rdJuJX
74Zjc1AjoimYxZwKZS8bphlIHe2/DQY=
=kl1G
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=3BsX
-----END PGP SIGNATURE-----
Merge tag 'riscv-dt-for-v6.8' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetrees for v6.8
StarFive:
Key peripheral support for the jh7100 that depended on the non-standard
non-coherent DMA operations, namely mmc, sdcard and sdio wifi. This
platform has long been supported out of tree by Emil and Ubuntu etc ship
images for it, so having mainline support for a wider range of
peripherals (at last) is great.
Microchip:
The flash used by Auto Update support and the corresponding QSPI
controller are added. On publicly available Icicle kits this flash is
not usable (engineering sample silicon issues) but in the future Icicle
kits will be available that have production silicon.
T-Head:
Jisheng is busy with RL this cycle and hence T-Head appears here. The
Lichee Pi and BeagleV both grow eMMC and uSD support.
Sopgho:
Support for the Huashan Pi and the cv1812h SoC it uses. The cv1812h is
almost identical to the existing cv1800b SoC. These SoCs are intended
for use in IP camera type systems but also appear on SBCs, with the last
digit denoting the amount integrated DDR3 the device has. The difference
between the cv1812h and the existing cv180x devices appears to be the
addition of video output interfaces.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.8' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: starfive: Enable SDIO wifi on JH7100 boards
riscv: dts: starfive: Enable SD-card on JH7100 boards
riscv: dts: starfive: Add JH7100 MMC nodes
riscv: dts: starfive: Add pool for coherent DMA memory on JH7100 boards
riscv: dts: starfive: Add JH7100 cache controller
riscv: dts: starfive: Mark the JH7100 as having non-coherent DMAs
riscv: dts: starfive: Group tuples in interrupt properties
riscv: dts: thead: Enable LicheePi 4A eMMC and microSD
riscv: dts: thead: Enable BeagleV Ahead eMMC and microSD
riscv: dts: thead: Add TH1520 mmc controllers and sdhci clock
riscv: dts: microchip: add the mpfs' system controller qspi & associated flash
riscv: dts: sophgo: add Huashan Pi board device tree
riscv: dts: sophgo: add initial CV1812H SoC device tree
riscv: dts: sophgo: cv18xx: Add gpio devices
riscv: dts: sophgo: Separate compatible specific for CV1800B soc
dt-bindings: riscv: Add SOPHGO Huashan Pi board compatibles
dt-bindings: timer: Add SOPHGO CV1812H clint
dt-bindings: interrupt-controller: Add SOPHGO CV1812H plic
Link: https://lore.kernel.org/r/20231221-skimmed-boxy-b78aed8afdc4@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add pinctrl and MMC controller nodes for the Broadcom wifi controller
on the BeagleV Starlight and StarFive VisionFive V1 boards.
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add pinctrl and MMC device tree nodes for the SD-card on the
BeagleV Starlight and StarFive VisionFive V1 boards.
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add device tree nodes for the Synopsis MMC controllers on the
StarFive JH7100 SoC.
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The StarFive JH7100 SoC has non-coherent device DMAs, but most drivers
expect to be able to allocate coherent memory for DMA descriptors and
such. However on the JH7100 DDR memory appears twice in the physical
memory map, once cached and once uncached:
0x00_8000_0000 - 0x08_7fff_ffff : Off chip DDR memory, cached
0x10_0000_0000 - 0x17_ffff_ffff : Off chip DDR memory, uncached
To use this uncached region we create a global DMA memory pool there and
reserve the corresponding area in the cached region.
However the uncached region is fully above the 32bit address limit, so add
a dma-ranges map so the DMA address used for peripherals is still in the
regular cached region below the limit.
Link: https://github.com/starfive-tech/JH7100_Docs/blob/main/JH7100%20Data%20Sheet%20V01.01.04-EN%20(4-21-2021).pdf
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The StarFive JH7100 SoC also features the SiFive L2 cache controller,
so add the device tree nodes for it.
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
To improve human readability and enable automatic validation, the tuples
in the various properties containing interrupt specifiers should be
grouped.
Fix this by grouping the tuples of "interrupts-extended" properties
using angle brackets.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add emmc node properties for the eMMC device and add sdio0 node
properties for the microSD slot. Set the frequency for the sdhci
reference clock.
Signed-off-by: Drew Fustini <dfustini@baylibre.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add emmc node properties for the eMMC device and add sdio0 node
properties for the microSD slot. Set the frequency for the sdhci
reference clock.
Signed-off-by: Drew Fustini <dfustini@baylibre.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add node for the fixed reference clock used for emmc and sdio nodes.
Add emmc node for the 1st dwcmshc instance which is typically connected
to an eMMC device. Add sdio0 node for the 2nd dwcmshc instance which is
typically connected to microSD slot. Add sdio1 node for the 3rd dwcmshc
instance which is typically connected to an SDIO WiFi module. The node
names are based on Table 1-2 C910/C906 memory map in the TH1520 System
User Manual.
Link: https://git.beagleboard.org/beaglev-ahead/beaglev-ahead/-/tree/main/docs
Signed-off-by: Drew Fustini <dfustini@baylibre.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The system controller's flash can be accessed via an MSS-exposed QSPI
controller sitting, which sits between the mailbox's control & data
registers. On Icicle, it has an MT25QL01GBBB8ESF connected to it.
The system controller and MSS both have separate QSPI controllers, both
of which can access the flash, although the system controller takes
priority.
Unfortunately, on engineering sample silicon, such as that on Icicle
kits, the MSS' QSPI controller cannot write to the flash due to a bug.
As a workaround, a QSPI controller can be implemented in the FPGA
fabric and the IO routing modified to connect it to the flash in place
of the "hard" controller in the MSS.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add initial device tree for the CV1812H RISC-V SoC by SOPHGO.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Acked-by: Chen Wang <unicorn_wang@outlook.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
As CV180x and CV181x have the identical layouts, it is OK to use the
cv1800b basic device tree for the whole series.
For CV1800B soc specific compatible, just move them out of the common
file.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Acked-by: Chen Wang <unicorn_wang@outlook.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The timebase-frequency on PolarFire SoC is not set by an oscillator on
the board, but rather by an internal divider, so move the property to
mpfs.dtsi.
This looks to be copy-pasta from the SiFive Unleashed as the comments
in both places were almost identical. In the Unleashed's case this looks
to actually be valid, as the clock is provided by a crystal on the PCB.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
---
CC: Conor Dooley <conor.dooley@microchip.com>
CC: Daire McNamara <daire.mcnamara@microchip.com>
CC: Rob Herring <robh+dt@kernel.org>
CC: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
CC: Paul Walmsley <paul.walmsley@sifive.com>
CC: Palmer Dabbelt <palmer@dabbelt.com>
CC: linux-riscv@lists.infradead.org
CC: devicetree@vger.kernel.org
A recent submission [1] from Rob has added additionalProperties: false
to the interrupt-controller child node of RISC-V cpus, highlighting that
the new cv1800b DT has been incorrectly using #address-cells.
It has no child nodes, so #address-cells is not needed. Remove it.
Link: https://patchwork.kernel.org/project/linux-riscv/patch/20230915201946.4184468-1-robh@kernel.org/ [1]
Fixes: c3dffa879c ("riscv: dts: sophgo: add initial CV1800B SoC device tree")
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Chen Wang <unicorn_wang@outlook.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Convert the RZ/Five devicetrees to use the new properties
"riscv,isa-base" & "riscv,isa-extensions".
For compatibility with other projects, "riscv,isa" remains.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231009-smog-gag-3ba67e68126b@wendy
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
There are a couple new SoCs that are supported for the first time:
- AMD Pensando Elba is a data processing unit based on Cortex-A72
CPU cores
- Sophgo makes RISC-V based chips, and we now support the CV1800B
chip used in the milkv-duo board and the massive sg2042 chip in the
milkv-pioneer, a 64-core developer workstation.
- Qualcomm Snapdragon 720G (sm7125) is a close relative of
Snapdragon 7c and gets added with some Xiaomi phones
- Renesas gains support for the R8A779F4 (R-Car S4-8) automotive
SoC and the RZ/G3S (R9A08G045) embedded SoC.
There are also a bunch of newly supported machines that use
already supported chips. On the 32-bit side, we have:
- USRobotics USR8200 is a NAS/Firewall/router based on the ancient
Intel IXP4xx platform
- A couple of machines based on the NXP i.MX5 and i.MX6 platforms
- One machine each for Allwinner V3s, Aspeed AST2600, Microchip
sama5d29 and ST STM32mp157
The other ones all use arm64 cores on chips from allwinner,
amlogic, freescale, mediatek, qualcomm and rockchip.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmVC3jwACgkQYKtH/8kJ
Uic3Jg//UgKUEr6ckxInnDew/yHW5AOQ35NKWCLNDysZZVnnnWY44j98Sw++NXyY
WX9rdQBYWf6XZaIynCIF0RqkYSsuPw5jmEIy5PH/JwFkwEvUgv/FFd285MdHa/zR
Rw61K+Aqy/qUDzpEz75z+uy3A0DX6N3ZYP0qvKxzT+oKSkOVYz3rPN5VcMYuPCxO
SpXZMz4CPjBf4RCQeApo80JO3SIW0Mnx1Fu589fJrlWhqmlSer7WlmSA3OMcBmKC
5WgNljieEQidYIhlmZDLnDIL7ot2g+0ESz8nYky3UFRKR3MFDyi4yA7PJrr/EMsK
X7u8eEESrAqjpVJJKgo+q3foV1nYSaGt9vU/mxaiwme44mzhZLo/xfuzpylZRorW
9ny3bP5GaiReWog15sCzwM3D/H+eJbtDKKiU7QasmXjtl+k8i6hAtvuISVeYkPae
n+SdMh3rNsP8n71ybD6aKLp41bQbiO4iUgkyYLh7NHsuSLKq/+EKTiyYmXB6egAZ
eeN+JEKvFgwROHCt39UA0Fo+PbOmeOHbNywLMrr1hZPT3ytroe/rgJEt+qdrCzN7
JcKcNTSy2sQX/GIKQ5qHHmphWZsD38SoqsiPtfsrprZiMXwbER23vnFXh7CHGL4I
gAra/iNHSsHl5FrF43qhyZA9vCNDYvo13LbS/kyDZ7tO9Q+8M/Q=
=NnPm
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC DT updates from Arnd Bergmann:
"There are a couple new SoCs that are supported for the first time:
- AMD Pensando Elba is a data processing unit based on Cortex-A72 CPU
cores
- Sophgo makes RISC-V based chips, and we now support the CV1800B
chip used in the milkv-duo board and the massive sg2042 chip in the
milkv-pioneer, a 64-core developer workstation.
- Qualcomm Snapdragon 720G (sm7125) is a close relative of Snapdragon
7c and gets added with some Xiaomi phones
- Renesas gains support for the R8A779F4 (R-Car S4-8) automotive SoC
and the RZ/G3S (R9A08G045) embedded SoC.
There are also a bunch of newly supported machines that use already
supported chips. On the 32-bit side, we have:
- USRobotics USR8200 is a NAS/Firewall/router based on the ancient
Intel IXP4xx platform
- A couple of machines based on the NXP i.MX5 and i.MX6 platforms
- One machine each for Allwinner V3s, Aspeed AST2600, Microchip
sama5d29 and ST STM32mp157
The other ones all use arm64 cores on chips from allwinner, amlogic,
freescale, mediatek, qualcomm and rockchip"
* tag 'soc-dt-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (641 commits)
ARM: dts: BCM5301X: Set switch ports for Linksys EA9200
ARM: dts: BCM5301X: Set fixed-link for extra Netgear R8000 CPU ports
ARM: dts: BCM5301X: Explicitly disable unused switch CPU ports
ARM: dts: BCM5301X: Relicense Vivek's code to the GPL 2.0+ / MIT
ARM: dts: BCM5301X: Relicense Felix's code to the GPL 2.0+ / MIT
ARM: dts: BCM5301X: Set MAC address for Asus RT-AC87U
arm64: dts: socionext: add missing cache properties
riscv: dts: thead: convert isa detection to new properties
arm64: dts: Update cache properties for socionext
arm64: dts: ti: k3-am654-idk: Add ICSSG Ethernet ports
arm64: dts: ti: k3-am654-icssg2: add ICSSG2 Ethernet support
arm64: dts: ti: k3-am65-main: Add ICSSG IEP nodes
arm64: dts: ti: k3-am62p5-sk: Updates for SK EVM
arm64: dts: ti: k3-am62p: Add nodes for more IPs
arm64: dts: rockchip: Add Turing RK1 SoM support
dt-bindings: arm: rockchip: Add Turing RK1
dt-bindings: vendor-prefixes: add turing
arm64: dts: rockchip: Add DFI to rk3588s
arm64: dts: rockchip: Add DFI to rk356x
arm64: dts: rockchip: Always enable DFI on rk3399
...
Convert the th1520 devicetrees to use the new properties
"riscv,isa-base" & "riscv,isa-extensions".
For compatibility with other projects, "riscv,isa" remains.
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231022154135.3746-1-jszhang@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
StarFive:
Things are a bit slower for StarFive this window, there's only the
addition of audio related DT nodes to speak of here.
Generic:
The SiFive, StarFive and Microchip devicetrees have had my replacement
ISA extension detection properties added. Unfortunately, the old
"riscv,isa" property never defined exactly what the extensions it
contained meant, and people were want to fill it in incorrectly (and
call upstream kernel devs idiots for not doing the same). The new
properties have explicit definitions and hopefully will stand up better
to some of the variation from RVI.
Sophgo:
Two new SoCs, one is probably the first of several with up/down tuned
variants, that have a pair of T-Head c906 cores and appear aimed at the
IP camera, smart <insert whatever> etc markets. They are intended to run
in AMP mode, with an RTOS on the less powerful core. The other is far
more interesting to kernel developers however, the 64-core SG2042, with
more recent c920 cores from T-Head at 2 GHz. For both, support is at a
very basic stage - some of the same developers are working on them as
other T-Head powered SoCs, but hopefully things will move beyond a basic
console boot. The goal is for Chen Wang to take over maintaining the
Sophgo support once they have some more experience with the process.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCZS1W8gAKCRB4tDGHoIJi
0mLBAP9fhiekHB8O7VQpcGvPB3FgFFh7uP8DzKcpU6bW8PbNmgD+MoCp4d/amMFR
VCtONbvM+RYC1ENRaOY91gI3k/2b0w8=
=2vZu
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=76M7
-----END PGP SIGNATURE-----
Merge tag 'riscv-dt-for-v6.7' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetrees for v6.7
StarFive:
Things are a bit slower for StarFive this window, there's only the
addition of audio related DT nodes to speak of here.
Generic:
The SiFive, StarFive and Microchip devicetrees have had my replacement
ISA extension detection properties added. Unfortunately, the old
"riscv,isa" property never defined exactly what the extensions it
contained meant, and people were want to fill it in incorrectly (and
call upstream kernel devs idiots for not doing the same). The new
properties have explicit definitions and hopefully will stand up better
to some of the variation from RVI.
Sophgo:
Two new SoCs, one is probably the first of several with up/down tuned
variants, that have a pair of T-Head c906 cores and appear aimed at the
IP camera, smart <insert whatever> etc markets. They are intended to run
in AMP mode, with an RTOS on the less powerful core. The other is far
more interesting to kernel developers however, the 64-core SG2042, with
more recent c920 cores from T-Head at 2 GHz. For both, support is at a
very basic stage - some of the same developers are working on them as
other T-Head powered SoCs, but hopefully things will move beyond a basic
console boot. The goal is for Chen Wang to take over maintaining the
Sophgo support once they have some more experience with the process.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.7' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux: (22 commits)
riscv: dts: starfive: convert isa detection to new properties
riscv: dts: sifive: convert isa detection to new properties
riscv: dts: microchip: convert isa detection to new properties
riscv: dts: sophgo: add Milk-V Duo board device tree
riscv: dts: sophgo: add initial CV1800B SoC device tree
dt-bindings: riscv: Add Milk-V Duo board compatibles
dt-bindings: timer: Add SOPHGO CV1800B clint
dt-bindings: interrupt-controller: Add SOPHGO CV1800B plic
riscv: defconfig: enable SOPHGO SoC
riscv: dts: sophgo: add Milk-V Pioneer board device tree
riscv: dts: add initial Sophgo SG2042 SoC device tree
dt-bindings: interrupt-controller: Add Sophgo sg2042 CLINT mswi
dt-bindings: timer: Add Sophgo sg2042 CLINT timer
dt-bindings: interrupt-controller: Add Sophgo SG2042 PLIC
dt-bindings: riscv: Add T-HEAD C920 compatibles
dt-bindings: riscv: add sophgo sg2042 bindings
dt-bindings: vendor-prefixes: add milkv/sophgo
riscv: Add SOPHGO SOC family Kconfig support
riscv: dts: starfive: add assigned-clock* to limit frquency
riscv: dts: starfive: Add JH7110 PWM-DAC support
...
Link: https://lore.kernel.org/r/20231016-filing-payroll-7aca51b8f1a3@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Convert the jh7100 and jh7110 devicetrees to use the new properties
"riscv,isa-base" & "riscv,isa-extensions".
For compatibility with other projects, "riscv,isa" remains.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Convert the fu540 and fu740 devicetrees to use the new properties
"riscv,isa-base" & "riscv,isa-extensions".
For compatibility with other projects, "riscv,isa" remains.
Reviewed-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Convert the PolarFire SoC devicetrees to use the new properties
"riscv,isa-base" & "riscv,isa-extensions".
For compatibility with other projects, "riscv,isa" remains.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Convert the D1 devicetrees to use the new properties
"riscv,isa-base" & "riscv,isa-extensions".
For compatibility with other projects, "riscv,isa" remains.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231009-moonlight-gray-92debdc89f30@wendy
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The ss pin of spi0 is the same as sck pin. According to the
visionfive 2 documentation, it should be pin 49 instead of 48.
Fixes: 74fb20c8f0 ("riscv: dts: starfive: Add spi node and pins configuration")
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Milk-V Duo[1] board is an embedded development platform based on the
CV1800B chip. Add minimal device tree files for the development board.
Support basic uart drivers, so supports booting to a basic shell.
Link: https://milkv.io/duo [1]
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Chen Wang <unicorn_wang@outlook.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add initial device tree for the CV1800B RISC-V SoC by SOPHGO.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Chen Wang <unicorn_wang@outlook.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Milk-V Pioneer [1] is a developer motherboard based on SG2042
in a standard mATX form factor.
Currently only support booting into console with only uart
enabled, other features will be added soon later.
Link: https://milkv.io/pioneer [1]
Reviewed-by: Guo Ren <guoren@kernel.org>
Acked-by: Chao Wei <chao.wei@sophgo.com>
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Milk-V Pioneer motherboard is powered by SG2042.
SG2042 is server grade chip with high performance, low power
consumption and high data throughput.
Key features:
- 64 RISC-V cpu cores
- 4 cores per cluster, 16 clusters on chip
- More info is available at [1].
Currently only support booting into console with only uart,
other features will be added soon later.
Link: https://en.sophgo.com/product/introduce/sg2042.html [1]
Reviewed-by: Guo Ren <guoren@kernel.org>
Acked-by: Chao Wei <chao.wei@sophgo.com>
Co-developed-by: Xiaoguang Xing <xiaoguang.xing@sophgo.com>
Signed-off-by: Xiaoguang Xing <xiaoguang.xing@sophgo.com>
Co-developed-by: Inochi Amaoto <inochiama@outlook.com>
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Now that noncoherent dma support for the RZ/Five SoC has been added, enable
the IP blocks which were disabled on the RZ/Five SMARC. This adds
support for the below peripherals:
* Ethernet
* DMAC
* SDHI
* USB
* RSPI
* SSI
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230929000704.53217-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
RZ/Five is a noncoherent SoC so to indicate this add dma-noncoherent
property to RZ/Five SoC DTSI.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230929000704.53217-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
In JH7110 SoC, we need to go by-pass mode, so we need add the
assigned-clock* properties to limit clock frquency.
Signed-off-by: William Qiu <william.qiu@starfivetech.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
A recent submission [1] from Rob has added additionalProperties: false
to the interrupt-controller child node of RISC-V cpus, highlighting that
the D1 DT has been incorrectly using #address-cells since its
introduction. It has no child nodes, so #address-cells is not needed.
Remove it.
Fixes: 077e5f4f55 ("riscv: dts: allwinner: Add the D1/D1s SoC devicetree")
Link: https://patchwork.kernel.org/project/linux-riscv/patch/20230915201946.4184468-1-robh@kernel.org/ [1]
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230916-saddling-dastardly-8cf6d1263c24@spud
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Documentation/process/license-rules.rst and checkpatch expect the SPDX
identifier syntax for multiple licenses to use capital "OR". Correct it
to keep consistent format and avoid copy-paste issues.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230823085238.113642-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
These pins are actually I2STX1 clock input, not I2STX0,
so their names should be changed.
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Reviewed-by: Walker Chen <walker.chen@starfivetech.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Node uart0_pins should be sorted alphabetically.
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
usb0 was disabled by mistake when merging, so enable it.
Fixes: e7c304c034 ("riscv: dts: starfive: jh7110: add the node and pins configuration for tdm")
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The Starfive VisionFive 2 has a 16MiB NOR flash, while the reserved-data
partition is declared starting at address 0x600000 with a size of
0x1000000. This causes the kernel to output the following warning:
[ 22.156589] mtd: partition "reserved-data" extends beyond the end of device "13010000.spi.0" -- size truncated to 0xa00000
It seems to be a confusion between the size of the partition and the end
address. Fix that by specifying the right size.
Fixes: 8384087a42 ("riscv: dts: starfive: Add QSPI controller node for StarFive JH7110 SoC")
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
T-Head:
Add a second minimal devicetree for the second board using the th1520
SoC, the BeagleV Ahead. As with the Lichee Pi 4a, this is sufficient
only for booting to a console, with work on the mmc, clocks and ethernet
sides of things under way. A relicense to a dual licence for the
existing devicetree files is also done, for good measure.
RISC-V Devicetrees for v6.6-pt2
StarFive:
Fix the sort order of some nodes that I resolved incorrectly during a
merge conflict.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCZOCDsgAKCRB4tDGHoIJi
0mEDAQDc1z032ZsKJSE/WBV0R8hw47RZoP22xHCP3d38vDfP3wEAsF6Kc0U+t8TQ
6CNGHUNpEkVJIdj/wOL8Zk0gV/GdLAA=
=F146
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=3ypd
-----END PGP SIGNATURE-----
Merge tag 'riscv-dt-for-v6.6-pt2' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetrees for v6.6 Part 2
T-Head:
Add a second minimal devicetree for the second board using the th1520
SoC, the BeagleV Ahead. As with the Lichee Pi 4a, this is sufficient
only for booting to a console, with work on the mmc, clocks and ethernet
sides of things under way. A relicense to a dual licence for the
existing devicetree files is also done, for good measure.
RISC-V Devicetrees for v6.6-pt2
StarFive:
Fix the sort order of some nodes that I resolved incorrectly during a
merge conflict.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.6-pt2' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: change TH1520 files to dual license
riscv: dts: thead: add BeagleV Ahead board device tree
dt-bindings: riscv: Add BeagleV Ahead board compatibles
riscv: dts: starfive: fix jh7110 qspi sort order
Link: https://lore.kernel.org/r/20230819-unwieldy-railing-9bba2b176aa7@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The BeagleV Ahead single board computer uses the T-Head TH1520 SoC.
Add a minimal device tree to support basic uart/gpio/dmac drivers so
that a user can boot to a basic shell.
Link: https://beagleboard.org/beaglev-ahead
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Drew Fustini <dfustini@baylibre.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Emil pointed out that "13010000 sorts after 12070000". Reshuffle the
entries to be in-order.
Reported-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
StarFive:
There's only StarFive stuff this time around, starting with some
bindings to get clock ID defines out of the binding headers. Getting
these (and the syscon bindings) in unblocked a swathe of stuff sitting
on the list. Added are: new clock controllers and sycons, ethernet
support, thermal sensors, USB and PCIe PHYs, hwrng, mmc and a few more
besides for the VisionFive v2. The original VisionFive and BeagleV
Starlight got some the thermal sensor support too, as that is supported
by the same driver. These changes make the board actually usable with
something other than an initramfs.
Overlay support by way of the -@ flag set during dtb building, is added
also.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCZNiusAAKCRB4tDGHoIJi
0u5JAP90hKhmPTWqxdRpnFrWi83k9RX4J6k5LHrqyt3e0sZ0HAD+JNiv4i4j8fDv
fm7usmraq8B2zLaV/AFmj9kiqdx0JgU=
=AH1c
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=+tgF
-----END PGP SIGNATURE-----
Merge tag 'riscv-dt-for-v6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetrees for v6.6
StarFive:
There's only StarFive stuff this time around, starting with some
bindings to get clock ID defines out of the binding headers. Getting
these (and the syscon bindings) in unblocked a swathe of stuff sitting
on the list. Added are: new clock controllers and sycons, ethernet
support, thermal sensors, USB and PCIe PHYs, hwrng, mmc and a few more
besides for the VisionFive v2. The original VisionFive and BeagleV
Starlight got some the thermal sensor support too, as that is supported
by the same driver. These changes make the board actually usable with
something other than an initramfs.
Overlay support by way of the -@ flag set during dtb building, is added
also.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux: (26 commits)
riscv: dts: starfive: jh7110: Fix GMAC configuration
riscv: dts: starfive - Add hwrng node for JH7110 SoC
riscv: dts: starfive - Add crypto and DMA node for JH7110
riscv: dts: starfive: Add mmc nodes on VisionFive 2 board
riscv: dts: starfive: enable DCDC1&ALDO4 node in axp15060
riscv: dts: starfive: Add QSPI controller node for StarFive JH7110 SoC
riscv: dts: starfive: jh7110: add the node and pins configuration for tdm
riscv: dts: starfive: jh7110: add dma controller node
riscv: dts: starfive: Add spi node and pins configuration
riscv: dts: starfive: Add USB dts node for JH7110
riscv: dts: starfive: Add USB and PCIe PHY nodes for JH7110
riscv: dts: starfive: jh7110: Add temperature sensor node and thermal-zones
riscv: dts: starfive: jh7100: Add temperature sensor node and thermal-zones
riscv: dts: starfive: visionfive 2: Add configuration of gmac and phy
riscv: dts: starfive: jh7110: Add ethernet device nodes
riscv: dts: starfive: jh7110: Add PLL clocks source in SYSCRG node
riscv: dts: starfive: jh7110: Add syscon nodes
riscv: dts: starfive: jh7110: Add STGCRG/ISPCRG/VOUTCRG nodes
riscv: dts: starfive: jh7110: Add DVP and HDMI TX pixel external clocks
dt-bindings: clock: Add StarFive JH7110 Video-Output clock and reset generator
...
Link: https://lore.kernel.org/r/20230813-naturist-fragment-ac7d10c453ba@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Allwinner D1, T113 provide two CAN controllers that are variants
of the R40 controller.
I have tested support for these controllers on two boards:
- A Lichee Panel RV 86 Panel running a D1 chip
- A Mango Pi MQ Dual running a T113-s3 chip
Both of these fully support both CAN controllers.
Signed-off-by: John Watts <contact@jookia.org>
Link: https://lore.kernel.org/r/20230807191952.2019208-1-contact@jookia.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add the mmc nodes for the StarFive JH7110 SoC.
Set mmc0 node to emmc and set mmc1 node to sd.
Signed-off-by: William Qiu <william.qiu@starfivetech.com>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Enable DCDC1 node for vmmc-supply and enable ALDO4 node for
vqmmc-supply.
Signed-off-by: William Qiu <william.qiu@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
This patch adds declaration of the general purpose ADC for D1
and T113s SoCs.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230619154252.3951913-5-bigunclemax@gmail.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Add the tdm controller node and pins configuration of tdm for the
StarFive JH7110 SoC.
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Walker Chen <walker.chen@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add USB and PCIe PHY dts nodes for the StarFive JH7110 SoC.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
dtbs_check w/ W=1 complains:
Warning (unit_address_vs_reg): /soc/ethernet@11c20000/ethernet-phy@7: node has a unit name, but no reg or ranges property
Warning (avoid_unnecessary_addr_size): /soc/ethernet@11c20000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
The ethernet@11c20000 node is guarded by an `#if (!SW_ET0_EN_N)` in
rzg2ul-smarc-som.dtsi, where the phy child node is added. In
rzfive-smarc-som.dtsi, the ethernet node is marked disabled & the
interrupt properties are deleted from the phy child node. As a result,
the produced dts looks like:
ethernet@11c20000 {
compatible = "renesas,r9a07g043-gbeth",
"renesas,rzg2l-gbeth";
/* snip */
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
ethernet-phy@7 {
};
};
Adding a corresponding `#if (!SW_ET0_EN_N)` around the node in
rzfive-smarc-som.dtsi avoids the complaint, as the empty child node is
not added:
ethernet@11c20000 {
compatible = "renesas,r9a07g043-gbeth",
"renesas,rzg2l-gbeth";
/* snip */
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230712-squealer-walmart-9587342ddec1@wendy
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add temperature sensor and thermal-zones support for
the StarFive JH7110 SoC. CPUFreq cooling is supported
in thermal-zones.
Co-developed-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add temperature sensor and thermal-zones support for
the StarFive JH7100 SoC.
Co-developed-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
v1.3B:
v1.3B uses motorcomm YT8531(rgmii-id phy) x2, need delay and
inverse configurations.
The tx_clk of v1.3B uses an external clock and needs to be
switched to an external clock source.
v1.2A:
v1.2A gmac0 uses motorcomm YT8531(rgmii-id) PHY, and needs delay
configurations.
v1.2A gmac1 uses motorcomm YT8512(rmii) PHY, and needs to
switch rx and rx to external clock sources.
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
[conor: squashed a fix from Samin to use the actual properties]
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add the '-@' DTC option for the starfive devices. This option
populates the '__symbols__' node that contains all the necessary symbols
for supporting device-tree overlays (for instance from the firmware or
the bootloader) on these devices.
The starfive devices allow various modules to be connected and this
enables users to create out-of-tree device-tree overlays for these modules.
Please note that this change does increase the size of the resulting DTB
by ~20%. For example, with v6.4 increase in size is as follows:
jh7100-beaglev-starlight.dtb 6192 -> 7339
jh7100-starfive-visionfive-v1.dtb 6281 -> 7428
jh7110-starfive-visionfive-2-v1.2a.dtb 11101 -> 13447
jh7110-starfive-visionfive-2-v1.3b.dtb 11101 -> 13447
Signed-off-by: Felix Moessbauer <felix.moessbauer@siemens.com>
Acked-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
T-Head:
Add a basic dtsi, Kconfig bits & trivial binding additions for the T-Head
1520 SoC (codename "light"). This SoC can be found on the Lichee Pi 4a,
for which a minimal dts is added.
Misc:
Re-sort the dts Makefile to be in alphanumerical order by directory.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCZJDOAwAKCRB4tDGHoIJi
0gAoAQCqGDPqdw5MdT/+tTJqkAIVFo3KyxSrMHvv3TE36Xp1HgEAxJQ+NoZ30nhx
pbaJaRcZDw7PKOVmMJ92R564EMdjngA=
=hJMo
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=U5qO
-----END PGP SIGNATURE-----
Merge tag 'riscv-dt-for-v6.5-pt2' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetrees for v6.5 Part 2
T-Head:
Add a basic dtsi, Kconfig bits & trivial binding additions for the T-Head
1520 SoC (codename "light"). This SoC can be found on the Lichee Pi 4a,
for which a minimal dts is added.
Misc:
Re-sort the dts Makefile to be in alphanumerical order by directory.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.5-pt2' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: sort makefile entries by directory
riscv: defconfig: enable T-HEAD SoC
MAINTAINERS: add entry for T-HEAD RISC-V SoC
riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
riscv: dts: add initial T-HEAD TH1520 SoC device tree
riscv: Add the T-HEAD SoC family Kconfig option
dt-bindings: riscv: Add T-HEAD TH1520 board compatibles
dt-bindings: timer: Add T-HEAD TH1520 clint
dt-bindings: interrupt-controller: Add T-HEAD's TH1520 PLIC
Link: https://lore.kernel.org/r/20230620-fidelity-variety-60b47c889e31@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
StarFive:
Watchdog nodes for both the JH7110 & its forerunner, the JH7100. PMU, P
being power, support for the JH7110. PMIC and frequency scaling support
for the JH7110 equipped VisionFive 2.
Most of the DT bits for the JH7110, and the SBCs using it, are pending
support for one of the clock controllers, so it's a smaller set of
changes than I would have hoped for.
Misc:
Pick up some dt-binding cleanup that Palmer assigned to me & had no
uptake from the respective maintainers. My powers of estimation failed
me again, with part of my motivation for picking them up being the
addition of new platforms that ended up not making it. Hopefully next
window for those, as they were relatively close.
Exclude the Allwinner and Renesas subdirectories from the Misc.
MAINTAINERS entry, since I do not take care of those.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCZIdfVAAKCRB4tDGHoIJi
0mspAP4m1zrOWojsDmwpodCajBTW6PEtMAztxRUj/qeA4IEsYgEA+NI1DhrUkwZ6
K1vw1VzP56auVkdS3X7ZBhEpjfnkCg4=
=JA/v
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=NR4f
-----END PGP SIGNATURE-----
Merge tag 'riscv-dt-for-v6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetrees for v6.5
StarFive:
Watchdog nodes for both the JH7110 & its forerunner, the JH7100. PMU, P
being power, support for the JH7110. PMIC and frequency scaling support
for the JH7110 equipped VisionFive 2.
Most of the DT bits for the JH7110, and the SBCs using it, are pending
support for one of the clock controllers, so it's a smaller set of
changes than I would have hoped for.
Misc:
Pick up some dt-binding cleanup that Palmer assigned to me & had no
uptake from the respective maintainers. My powers of estimation failed
me again, with part of my motivation for picking them up being the
addition of new platforms that ended up not making it. Hopefully next
window for those, as they were relatively close.
Exclude the Allwinner and Renesas subdirectories from the Misc.
MAINTAINERS entry, since I do not take care of those.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: starfive: Add cpu scaling for JH7110 SoC
riscv: dts: starfive: Enable axp15060 pmic for cpufreq
dt-bindings: interrupt-controller: sifive,plic: Sort compatible values
dt-bindings: timer: sifive,clint: Clean up compatible value section
riscv: dts: starfive: jh7110: Add watchdog node
riscv: dts: starfive: jh7100: Add watchdog node
riscv: dts: starfive: Add PMU controller node
MAINTAINERS: exclude maintained subdirs in RISC-V misc DT entry
Link: https://lore.kernel.org/r/20230612-fasting-floss-0bc05a08bc7a@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
New additions to the list have tried to respect alphanumeric ordering,
but the thing was out of order to start with. Sort it.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Jisheng Zhang <jszhang@kernel.org> says:
Sipeed's Lichee Pi 4A development board uses Lichee Module 4A core
module which is powered by T-HEAD's TH1520 SoC. Add minimal device
tree files for the core module and the development board.
Support basic uart/gpio/dmac drivers, so supports booting to a basic
shell.
This also pulls in -rc2, because of some maintainers re-jigging that
went on in the interim in commit 80e62bc848 ("MAINTAINERS: re-sort
all entries and fields").
Link: https://lore.kernel.org/r/20230617161529.2092-1-jszhang@kernel.org
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Sipeed's Lichee Pi 4A development board uses Lichee Module 4A core
module which is powered by T-HEAD's TH1520 SoC. Add minimal device
tree files for the core module and the development board.
Support basic uart/gpio/dmac drivers, so supports booting to a basic
shell.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add initial device tree for the TH1520 RISC-V SoC by T-HEAD.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add the operating-points-v2 to support cpu scaling on StarFive JH7110 SoC.
It supports up to 4 cpu frequency loads.
Signed-off-by: Mason Huo <mason.huo@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The VisionFive 2 board has an embedded pmic axp15060,
which supports the cpu DVFS through the dcdc2 regulator.
This patch enables axp15060 pmic and configs the dcdc2.
Signed-off-by: Mason Huo <mason.huo@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Some boards form the MangoPi family (MQ\MQ-Dual\MQ-R) may have
an optional SPI flash that connects to the SPI0 controller.
This controller is the same for R329/D1/R528/T113s SoCs and
should be supported by the sun50i-r329-spi driver.
So let's add its DT nodes.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230510081121.3463710-6-bigunclemax@gmail.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Add the pmu controller node for the StarFive JH7110 SoC. The PMU needs
to be used by other modules, e.g. VPU,ISP,etc.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Walker Chen <walker.chen@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The devicetree changes overall are again dominated by the Qualcomm
Snapdragon platform that weighs in at over 300 changesets, but there
are many updates across other platforms as well, notably Mediatek, NXP,
Rockchips, Renesas, TI, Samsung and ST Microelectronics. These all
add new features for existing machines, as well as new machines and
SoCs.
The newly added SoCs are:
- Allwinner T113-s, an Cortex-A7 based variant of the RISC-V
based D1 chip.
- StarFive JH7110, a RISC-V SoC based on the Sifive U74 core
like its JH7100 predecessor, but with additional CPU cores
and a GPU.
- Apple M2 as used in current Macbook Air/Pro and Mac Mini
gets added, with comparable support as its M1 predecessor.
- Unisoc UMS512 (Tiger T610) is a midrange smartphone SoC
- Qualcomm IPQ5332 and IPQ9574 are Wi-Fi 7 networking SoCs,
based on the Cortex-A53 and Cortex-A73 cores, respectively.
- Qualcomm sa8775p is an automotive SoC derived from the
Snapdragon family.
Including the initial board support for the added SoC platforms,
there are 52 new machines. The largest group are 19 boards
industrial embedded boards based on the NXP i.MX6 (32-bit)
and i.MX8 (64-bit) families.
Others include:
- Two boards based on the Allwinner f1c200s ultra-low-cost chip
- Three "Banana Pi" variants based on the Amlogic g12b
(A311D, S922X) SoC.
- The Gl.Inet mv1000 router based on Marvell Armada 3720
- A Wifi/LTE Dongle based on Qualcomm msm8916
- Two robotics boards based on Qualcomm QRB chips
- Three Snapdragon based phones made by Xiaomi
- Five developments boards based on various Rockchip SoCs,
including the rk3588s-khadas-edge2 and a few NanoPi
models
- The AM625 Beagleplay industrial SBC
Another 14 machines get removed: both boards for the obsolete "oxnas"
platform, three boards for the Renesas r8a77950 SoC that were only for
pre-production chips, and various chromebook models based on the Qualcomm
Sc7180 "trogdor" design that were never part of products.
-----BEGIN PGP SIGNATURE-----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=j12m
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC devicetree updates from Arnd Bergmann:
"The devicetree changes overall are again dominated by the Qualcomm
Snapdragon platform that weighs in at over 300 changesets, but there
are many updates across other platforms as well, notably Mediatek,
NXP, Rockchips, Renesas, TI, Samsung and ST Microelectronics. These
all add new features for existing machines, as well as new machines
and SoCs.
The newly added SoCs are:
- Allwinner T113-s, an Cortex-A7 based variant of the RISC-V based D1
chip.
- StarFive JH7110, a RISC-V SoC based on the Sifive U74 core like its
JH7100 predecessor, but with additional CPU cores and a GPU.
- Apple M2 as used in current Macbook Air/Pro and Mac Mini gets
added, with comparable support as its M1 predecessor.
- Unisoc UMS512 (Tiger T610) is a midrange smartphone SoC
- Qualcomm IPQ5332 and IPQ9574 are Wi-Fi 7 networking SoCs, based on
the Cortex-A53 and Cortex-A73 cores, respectively.
- Qualcomm sa8775p is an automotive SoC derived from the Snapdragon
family.
Including the initial board support for the added SoC platforms, there
are 52 new machines. The largest group are 19 boards industrial
embedded boards based on the NXP i.MX6 (32-bit) and i.MX8 (64-bit)
families.
Others include:
- Two boards based on the Allwinner f1c200s ultra-low-cost chip
- Three 'Banana Pi' variants based on the Amlogic g12b (A311D, S922X)
SoC.
- The Gl.Inet mv1000 router based on Marvell Armada 3720
- A Wifi/LTE Dongle based on Qualcomm msm8916
- Two robotics boards based on Qualcomm QRB chips
- Three Snapdragon based phones made by Xiaomi
- Five developments boards based on various Rockchip SoCs, including
the rk3588s-khadas-edge2 and a few NanoPi models
- The AM625 Beagleplay industrial SBC
Another 14 machines get removed: both boards for the obsolete 'oxnas'
platform, three boards for the Renesas r8a77950 SoC that were only for
pre-production chips, and various chromebook models based on the
Qualcomm Sc7180 'trogdor' design that were never part of products"
* tag 'soc-dt-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (836 commits)
arm64: dts: rockchip: Add support for volume keys to rk3399-pinephone-pro
arm64: dts: rockchip: Add vdd_cpu_big regulators to rk3588-rock-5b
arm64: dts: rockchip: Use generic name for es8316 on Pinebook Pro and Rock 5B
arm64: dts: rockchip: Drop RTC clock-frequency on rk3588-rock-5b
arm64: dts: apple: t8112: Add PWM controller
arm64: dts: apple: t600x: Add PWM controller
arm64: dts: apple: t8103: Add PWM controller
arm64: dts: rockchip: Add pinctrl gpio-ranges for rk356x
ARM: dts: nomadik: Replace deprecated spi-gpio properties
ARM: dts: aspeed-g6: Add UDMA node
ARM: dts: aspeed: greatlakes: add mctp device
ARM: dts: aspeed: greatlakes: Add gpio names
ARM: dts: aspeed: p10bmc: Change power supply info
arm64: dts: mediatek: mt6795-xperia-m5: Add Bosch BMM050 Magnetometer
arm64: dts: mediatek: mt6795-xperia-m5: Add Bosch BMA255 Accelerometer
arm64: dts: mediatek: mt6795: Add tertiary PWM node
arm64: dts: rockchip: add panel to Anbernic RG353 series
dt-bindings: arm: Add Data Modul i.MX8M Plus eDM SBC
dt-bindings: arm: fsl: Add chargebyte Tarragon
dt-bindings: vendor-prefixes: add chargebyte
...
Commit 370f696e44 ("dt-bindings: serial: snps-dw-apb-uart: add dma &
dma-names properties") documented dma-names property to handle Allwinner
D1 dtbs_check warnings, but relies on the rx->tx ordering, which is the
reverse of what a bunch of different boards expect.
The initial proposed solution was to allow a flexible dma-names order in
the binding, due to potential ABI breakage concerns after fixing the DTS
files. But luckily the Allwinner boards are not affected, since they are
using a shared DMA channel for rx and tx.
Hence, the first step in fixing the inconsistency was to change
dma-names order in the binding to tx->rx.
Do the same for the snps,dw-apb-uart nodes in the DTS file.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230321215624.78383-7-cristian.ciocaltea@collabora.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Merge Hal's series adding support for the new StarFive JH7110 SoC.
There's a few bindings here for core components that were not picked up
by the various maintainers for the subsystems (previously Palmer would
pick these up via the RISC-V tree) & the first two commits in the branch
are shared with the clk tree, since the dts depends on defines in the
dt-binding headers.
This is based on -rc2, as the board does not actually boot on -rc1
due to the bug Linus introduced.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add a minimal device tree for StarFive JH7110 VisionFive 2 board
which has version A and version B. Support booting and basic
clock/reset/pinctrl/uart drivers.
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Co-developed-by: Jianlong Huang <jianlong.huang@starfivetech.com>
Signed-off-by: Jianlong Huang <jianlong.huang@starfivetech.com>
Co-developed-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The spi-max-frequency is a property of SPI children, not the
controller:
k210_generic.dtb: spi@50240000: Unevaluated properties are not allowed ('spi-max-frequency' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The mailbox on PolarFire SoC should really have three reg properties,
not two. Without splitting into three sections, the system controller's
QSPI cannot be accessed as it sits inside the current first range. The
driver & binding have been adapted to account for both two & three
ranges, so fix the dts too.
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
D1 contains a crypto engine which is supported by the sun8i-ce driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20221231220146.646-4-samuel@sholland.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The macb on PolarFire SoC has reset support which the generic compatible
does not use. Add the newly introduced MPFS specific compatible as the
primary compatible to avail of this support & wire up the reset to the
clock controllers devicetree entry.
Reviewed-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
About a quarter of the changes are for 32-bit arm, mostly filling in
device support for existing machines and adding minor cleanups, mostly
for Qualcomm and Samsung based machines.
Two new 32-bit SoCs are added, both are quad-core Cortex-A7 chips from
Rockchips that have been around for a while but were lacking kernel
support so far: RV1126 is a Vision SoC with an NPU and is used in the
Edgeble Neural Compute Module 2(Neu2) board, while RK3128 is design for
TV boxes and so far only comes with a dts for its refernece design.
The other 32-bit boards that were added are two ASpeed AST2600 based BMC
boards, the Microchip sam9x60_curiosity development board (Armv5 based!),
the Enclustra PE1 FPGA-SoM baseboard, and a few more boards for i.MX53
and i.MX6ULL.
On the RISC-V side, there are fewer patches, but a total of ten new
single-board computers based on variations of the Allwinner D1/T113 chip,
plus one more board based on Microchip Polarfire.
As usual, arm64 has by far the most changes here, with over 700 non-merge
changesets, among them over 400 alone for Qualcomm. The newly added SoCs
this time are all recent high-end embedded SoCs for various markets,
each on comes with support for its reference board:
- Qualcomm SM8550 (Snapdragon 8 Gen 2) for mobile phones
- Qualcomm QDU1000/QRU1000 5G RAN platform
- Rockchips RK3588/RK3588s for tablets, chromebooks and SBCs
- TI J784S4 for industrial and automotive applications
In total, there are 46 new arm64 machines:
- Reference platforms for each of the five new SoCs
- Three Amlogic based development boards
- Six embedded machines based on NXP i.MX8MM and i.MX8MP
- The Mediatek mt7986a based Banana Pi R3 router
- Six tablets based on Qualcomm MSM8916 (Snapdragon 410),
SM6115 (Snapdragon 662) and SM8250 (Snapdragon 865)
- Two LTE dongles, also based on MSM8916
- Seven mobile phones, based on Qualcomm MSM8953 (Snapdragon 610),
SDM450 and SDM632
- Three chromebooks based on Qualcomm SC7280 (Snapdragon 7c)
- Nine development boards based on Rockchips RK3588, RK3568,
RK3566 and RK3328.
- Five development machines based on TI K3 (AM642/AM654/AM68/AM69)
The cleanup of dtc warnings continues across all platforms, adding
to the total number of changes.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmPvpVYACgkQmmx57+YA
GNm3iA/+NgaiEgwxaot1eoBqKImyP6NtC9VHFYRbscVkaBEkdNpm2zeVX92E2/8d
dZuGiOqY5VC+e53Rbig6m0GLrctYJfZTdJ0tYih8cwkB0jVL6bHzFQE1ugZkXkQC
/dXx2ozNQD1XqfgXqi7OC2PeaBqBxOK4UFrhUvjfzR68GuZmWpdC4+1mdIs106D1
252vV3y3biMDKXg1SgTXc4t8nb/ZT69gJpgJdbNuypDcAVrqlLaQZQ1sdEUu2wsh
6XnBZKe8srkFFwN+eR0Tdf9MhneUFJxLQsAajAm4WN1QiGrqtU42mrpJE80b6Uic
wnkvgwfyGVeGivM4/bAkeug5dCiElzCiwQBCKzL95ucf75Z8SfmhFAVAqji/MFBF
yzfetUld975qI0Bw6zh9dJALz6hElZAbbvcGI1imlXjVIsOwINvCoB5r3YPJw7FR
2nhJrsXs8h37VZgkeTlMp5BMu9j0AQKoBL4zbOSdrDr+XuOvuzIez+8ashFLijvu
FO+qlXfHUC7WsR6wktVumCsADnVRPJZN0UeMhSFixceD/njVaRZBk3BOY5Ea9wjm
G0s3KpqnLgEMrjDW3FLBf8xb9qEQPBAyeYUL9d0MHByz8W7iI/dQjEie0UEzmCqI
J+cDdhMCKDNYOF0Xk8d9k2g5/p62/0akmncOBCZRJf9bMHklBWY=
=I8Ga
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC DT updates from Arnd Bergmann:
"About a quarter of the changes are for 32-bit arm, mostly filling in
device support for existing machines and adding minor cleanups, mostly
for Qualcomm and Samsung based machines.
Two new 32-bit SoCs are added, both are quad-core Cortex-A7 chips from
Rockchips that have been around for a while but were lacking kernel
support so far: RV1126 is a Vision SoC with an NPU and is used in the
Edgeble Neural Compute Module 2(Neu2) board, while RK3128 is design
for TV boxes and so far only comes with a dts for its refernece
design.
The other 32-bit boards that were added are two ASpeed AST2600 based
BMC boards, the Microchip sam9x60_curiosity development board (Armv5
based!), the Enclustra PE1 FPGA-SoM baseboard, and a few more boards
for i.MX53 and i.MX6ULL.
On the RISC-V side, there are fewer patches, but a total of ten new
single-board computers based on variations of the Allwinner D1/T113
chip, plus one more board based on Microchip Polarfire.
As usual, arm64 has by far the most changes here, with over 700
non-merge changesets, among them over 400 alone for Qualcomm. The
newly added SoCs this time are all recent high-end embedded SoCs for
various markets, each on comes with support for its reference board:
- Qualcomm SM8550 (Snapdragon 8 Gen 2) for mobile phones
- Qualcomm QDU1000/QRU1000 5G RAN platform
- Rockchips RK3588/RK3588s for tablets, chromebooks and SBCs
- TI J784S4 for industrial and automotive applications
In total, there are 46 new arm64 machines:
- Reference platforms for each of the five new SoCs
- Three Amlogic based development boards
- Six embedded machines based on NXP i.MX8MM and i.MX8MP
- The Mediatek mt7986a based Banana Pi R3 router
- Six tablets based on Qualcomm MSM8916 (Snapdragon 410), SM6115
(Snapdragon 662) and SM8250 (Snapdragon 865)
- Two LTE dongles, also based on MSM8916
- Seven mobile phones, based on Qualcomm MSM8953 (Snapdragon 610),
SDM450 and SDM632
- Three chromebooks based on Qualcomm SC7280 (Snapdragon 7c)
- Nine development boards based on Rockchips RK3588, RK3568, RK3566
and RK3328.
- Five development machines based on TI K3 (AM642/AM654/AM68/AM69)
The cleanup of dtc warnings continues across all platforms, adding to
the total number of changes"
* tag 'soc-dt-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (1035 commits)
dt-bindings: riscv: correct starfive visionfive 2 compatibles
ARM: dts: socfpga: Add enclustra PE1 devicetree
dt-bindings: altera: Add enclustra mercury PE1
arm64: dts: qcom: msm8996: align RPM G-Link clock-controller node with bindings
arm64: dts: qcom: qcs404: align RPM G-Link node with bindings
arm64: dts: qcom: ipq6018: align RPM G-Link node with bindings
arm64: dts: qcom: sm8550: remove invalid interconnect property from cryptobam
arm64: dts: qcom: sc7280: Adjust zombie PWM frequency
arm64: dts: qcom: sc8280xp-pmics: Specify interrupt parent explicitly
arm64: dts: qcom: sm7225-fairphone-fp4: enable remaining i2c busses
arm64: dts: qcom: sm7225-fairphone-fp4: move status property down
arm64: dts: qcom: pmk8350: Use the correct PON compatible
arm64: dts: qcom: sc8280xp-x13s: Enable external display
arm64: dts: qcom: sc8280xp-crd: Introduce pmic_glink
arm64: dts: qcom: sc8280xp: Add USB-C-related DP blocks
arm64: dts: qcom: sm8350-hdk: enable GPU
arm64: dts: qcom: sm8350: add GPU, GMU, GPU CC and SMMU nodes
arm64: dts: qcom: sm8350: finish reordering nodes
arm64: dts: qcom: sm8350: move more nodes to correct place
arm64: dts: qcom: sm8350: reorder device nodes
...
- High Performance mode (1.8 GHz) support for the Cortex-A76 CPU cores
on R-Car V4H,
- GPIO interrupt support for the RZ/G2UL SoC and the RZ/G2UL SMARC EVK
development board,
- USB Function support for the RZ/N1D SoC,
- Generic Sound Card driver examples for the Renesas R-Car Starter Kit
Premier/Pro and Shimafugi Kingfisher development board stack,
- Universal Flash Storage support for the Renesas Spider development
board,
- External Power Sequence Controller (PWC) support for the RZ/V2M SoC
and the RZ/V2M Evaluation Kit 2.0,
- IOMMU support for MMC on the R-Car S4-8 SoC,
- Miscellaneous fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCY9Oc1QAKCRCKwlD9ZEnx
cMRKAP0S0VgkOJU9n+qrDdFNYeCAwLkJbcpWMsc4xy/dxt1gIQEAxbnJpGcmdAis
qiY67N7RU8mST1R7QACUEcvygxvqLwI=
=dAM5
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=YAr2
-----END PGP SIGNATURE-----
Merge tag 'renesas-dts-for-v6.3-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas DT updates for v6.3 (take two)
- High Performance mode (1.8 GHz) support for the Cortex-A76 CPU cores
on R-Car V4H,
- GPIO interrupt support for the RZ/G2UL SoC and the RZ/G2UL SMARC EVK
development board,
- USB Function support for the RZ/N1D SoC,
- Generic Sound Card driver examples for the Renesas R-Car Starter Kit
Premier/Pro and Shimafugi Kingfisher development board stack,
- Universal Flash Storage support for the Renesas Spider development
board,
- External Power Sequence Controller (PWC) support for the RZ/V2M SoC
and the RZ/V2M Evaluation Kit 2.0,
- IOMMU support for MMC on the R-Car S4-8 SoC,
- Miscellaneous fixes and improvements.
* tag 'renesas-dts-for-v6.3-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (25 commits)
arm64: dts: renesas: r8a779f0: Add iommus to MMC node
arm64: dts: renesas: v2mevk2: Add PWC support
arm64: dts: renesas: r9a09g011: Add PWC support
arm64: dts: renesas: r9a09g011: Reword ethernet status
arm64: dts: renesas: r8a774[be]1-beacon: Sync aliases with RZ/G2M
arm64: dts: renesas: beacon-renesom: Fix audio clock rate
arm64: dts: renesas: beacon-renesom: Update Ethernet PHY ID
arm64: dts: renesas: beacon-renesom: Fix gpio expander reference
arm64: dts: renesas: spider-cpu: Enable UFS device
arm64: dts: renesas: Add ulcb{-kf} Simple Audio Card MIX + TDM Split dtsi
arm64: dts: renesas: Add ulcb{-kf} Audio Graph Card MIX + TDM Split dtsi
arm64: dts: renesas: Add ulcb{-kf} Audio Graph Card2 MIX + TDM Split dtsi
arm64: dts: renesas: Add ulcb{-kf} Simple Audio Card dtsi
arm64: dts: renesas: Add ulcb{-kf} Audio Graph Card2 dtsi
arm64: dts: renesas: Add ulcb{-kf} Audio Graph Card dtsi
arm64: dts: renesas: #sound-dai-cells is used when simple-card
ARM: dts: renesas: #sound-dai-cells is used when simple-card
arm64: dts: renesas: eagle: Add SCIF_CLK support
ARM: dts: r9a06g032: Add the USBF controller node
arm64: dts: renesas: rzg2ul-smarc-som: Add PHY interrupt support for ETH{0/1}
...
Link: https://lore.kernel.org/r/cover.1674815099.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Microchip:
A vendor prefix for Aldec and both a binding and Devicetree for the
Aldec TySoM devkit for PolarFire SoC. This Devicetree corresponds to
what they are shipping in the SDK for rev2 boards.
StarFive:
Just the binding for the new StarFive JH7110 SoC and its first-party
SDC the VisionFive 2.
Other:
I was expecting the Devicetree for the aforementioned board to be ready
for this window, as the pinctrl driver had seem some review prior to
v6.2 and both it & the base clock drivers are heavily based on the
existing drivers for the JH7110.
That didn't come to be.. Christmas, the RISC-V Summit in December and
the Lunar New Year all playing a part perhaps.
Because of that, both Palmer and I have the Kconfig.socs work in our
branches, although in hindsight it probably wasn't needed here as I
only added the TySoM Devicetree & the conflict would've been trivial.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCY9EPgwAKCRB4tDGHoIJi
0l9kAQDJHyrjfXMooRHSFXRUsJFYeN8MpYvD1CLavdrD+Pu+KQD/c1sApjfZrKjo
ItyEL37F2QJOAFY1rAxdB7d6ppsUEAQ=
=sN4y
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=SCZP
-----END PGP SIGNATURE-----
Merge tag 'riscv-dt-for-v6.3-mw0' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into arm/dt
RISC-V Devicetrees for v6.3-mw0
Microchip:
A vendor prefix for Aldec and both a binding and Devicetree for the
Aldec TySoM devkit for PolarFire SoC. This Devicetree corresponds to
what they are shipping in the SDK for rev2 boards.
StarFive:
Just the binding for the new StarFive JH7110 SoC and its first-party
SDC the VisionFive 2.
Other:
I was expecting the Devicetree for the aforementioned board to be ready
for this window, as the pinctrl driver had seem some review prior to
v6.2 and both it & the base clock drivers are heavily based on the
existing drivers for the JH7110.
That didn't come to be.. Christmas, the RISC-V Summit in December and
the Lunar New Year all playing a part perhaps.
Because of that, both Palmer and I have the Kconfig.socs work in our
branches, although in hindsight it probably wasn't needed here as I
only added the TySoM Devicetree & the conflict would've been trivial.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.3-mw0' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: microchip: add the Aldec TySoM's devicetree
dt-bindings: riscv: microchip: document the Aldec TySoM
dt-bindings: vendor-prefixes: Add entry for Aldec
RISC-V: stop directly selecting drivers for SOC_CANAAN
RISC-V: stop selecting SiFive clock and serial drivers directly
RISC-V: stop selecting the PolarFire SoC clock driver
RISC-V: kbuild: convert all use of SOC_FOO to ARCH_FOO
RISC-V: kconfig.socs: convert usage of SOC_CANAAN to ARCH_CANAAN
RISC-V: introduce ARCH_FOO kconfig aliases for SOC_FOO symbols
dt-bindings: riscv: Add StarFive JH7110 SoC and VisionFive 2 board
Link: https://lore.kernel.org/r/Y9LP+Za1h0fkBa58@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Allwinner D1 family of SoCs contain a PPU power domain controller
separate from the PRCM. It can power down the video engine and DSP, and
it contains special logic for hardware-assisted CPU idle.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230126063419.15971-4-samuel@sholland.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The 100ask Dongshan Nezha STU is a system-on-module that can be used
standalone or with a carrier board. The SoM provides gigabit Ethernet,
HDMI, a USB peripheral port, and WiFi/Bluetooth via an RTL8723DS chip.
The "DIY" carrier board exposes almost every pin from the D1 SoC to 0.1"
headers, but contains no digital circuitry, so it does not have its own
devicetree.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230126045738.47903-10-samuel@sholland.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The MangoPi MQ Pro is a tiny SBC with a layout compatible to the
Raspberry Pi Zero. It includes the Allwinner D1 SoC, 512M or 1G of DDR3,
and an RTL8723DS-based WiFi/Bluetooth module.
The board also exposes GPIO Port E via a connector on the end of the
board, which can support either a camera or an RMII Ethernet PHY. The
additional regulators supply that connector.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230126045738.47903-9-samuel@sholland.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Sipeed manufactures a "Lichee RV" system-on-module, which provides a
minimal working system on its own, as well as a few carrier boards. The
"Dock" board provides audio, USB, and WiFi. The "86 Panel" additionally
provides 100M Ethernet and a built-in display panel.
The 86 Panel repurposes the USB ID and VBUS detection GPIOs for its RGB
panel interface, since the USB OTG port is inaccessible inside the case.
Co-developed-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230126045738.47903-8-samuel@sholland.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
"D1 Nezha" is Allwinner's first-party development board for the D1 SoC.
It was shipped with 512M, 1G, or 2G of DDR3. It supports onboard audio,
HDMI, gigabit Ethernet, WiFi and Bluetooth, USB 2.0 host and OTG ports,
plus low-speed I/O from the SoC and a GPIO expander chip.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230126045738.47903-7-samuel@sholland.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The MangoPi MQ is a tiny SBC built around the Allwinner D1s. Its
onboard peripherals include two USB Type-C ports (1 device, 1 host)
and RTL8189FTV WLAN.
A MangoPi MQ-R variant of the board also exists. The MQ-R has a
different form factor, but the onboard peripherals are the same.
Most D1 and D1s boards use a similar power tree, with the 1.8V rail
powered by the SoC's internal LDOA, analog domains powered by ALDO,
and the rest of the board powered by always-on fixed regulators. To
avoid duplication, factor out the regulator information that is
common across boards.
The board also exposes GPIO Port E via a FPC connector, which can
support either a camera or an RMII Ethernet PHY. The additional
regulators supply that connector.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230126045738.47903-6-samuel@sholland.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
D1 (aka D1-H), D1s (aka F133), R528, and T113 are a family of SoCs based
on a single die, or at a pair of dies derived from the same design.
D1 and D1s contain a single T-HEAD Xuantie C906 CPU, whereas R528 and
T113 contain a pair of Cortex-A7's. D1 and R528 are the full version of
the chip with a BGA package, whereas D1s and T113 are low-pin-count QFP
variants.
Because the original design supported both ARM and RISC-V CPUs, some
peripherals are duplicated. In addition, all variants except D1s contain
a HiFi 4 DSP with its own set of peripherals.
The devicetrees are organized to minimize duplication:
- Common perhiperals are described in sunxi-d1s-t113.dtsi
- DSP-related peripherals are described in sunxi-d1-t113.dtsi
- RISC-V specific hardware is described in sun20i-d1s.dtsi
- Functionality unique to the D1 variant is described in sun20i-d1.dtsi
The SOC_PERIPHERAL_IRQ macro handles the different #interrupt-cells
values between the ARM (GIC) and RISC-V (PLIC) versions of the SoC.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@vrull.eu>
Tested-by: Heiko Stuebner <heiko.stuebner@vrull.eu>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230126045738.47903-5-samuel@sholland.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
IRQC support for RZ/Five is still missing so drop the interrupts and
interrupt-parent properties from the PHY nodes of ETH{0,1}.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230102222708.274369-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As it says on the tin, add a DT for this board. It's been sitting on my
desk for a while, so may as well have it upstream...
The DT is only partially complete, as it needs the fabric content added.
Unfortunately, I don't have a reference design in RTL or SmartDesign
for it and therefore don't know what that fabric content is.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The TySOM-M-MPFS250 is a compact SoC prototyping board featuring
a Microchip PolarFire SoC MPFS250T-FCG1152. Features include:
- 16 Gib FPGA DDR4
- 16 Gib MSS DDR4 with ECC
- eMMC
- SPI flash memory
- 2x Ethernet 10/100/1000
- USB 2.0
- PCIe x4 Gen2
- HDMI OUT
- 2x FMC connector (HPC and LPC)
Specifically flag this board as rev2, in case later boards have an
FPGA design revision with more features available in the future.
Link: https://www.aldec.com/en/products/emulation/tysom_boards/polarfire_microchip/tysom_m_mpfs250
[Fixed a mistake where I read 16 Gib as 16 GiB!]
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Enable OSTM{1,2} nodes on RZ/Five SMARC SoM.
Note, OSTM{1,2} nodes are enabled in the RZ/G2UL SMARC SoM DTSI [0] hence
deleting the disabled nodes from RZ/Five SMARC SoM DTSI enables it here
too as we include [0] in RZ/Five SMARC SoM DTSI.
[0] arch/arm64/boot/dts/renesas/rzg2ul-smarc-som.dtsi
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230102222233.274021-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The 32-bit memory resource is needed for non-prefetchable memory
allocations on the PCIe bus, however with some cards (such as the
SM768) the system fails to allocate memory from this.
Checking the allocation against the datasheet, it looks like there
has been a mis-calcualation of the resource for the first memory
region (0x0060090000..0x0070ffffff) which in the data-sheet for
the fu740 (v1p2) is from 0x0060000000..0x007fffffff. Changing
this to allocate from 0x0060090000..0x007fffffff fixes the probing
issues.
Fixes: ae80d51480 ("riscv: dts: Add PCIe support for the SiFive FU740-C000 SoC")
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: stable@vger.kernel.org
Tested-by: Ron Economos <re@w6rz.net> # from IRC
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Convert all non user visible use of SOC_FOO symbols to their ARCH_FOO
variants. The canaan DTs are an outlier in that they're gated at the
directory and the file level. Drop the directory level gating while we
are swapping the symbol names over.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Enable WDT node on RZ/Five SMARC SoM.
Note, WDT block is enabled in RZ/G2UL SMARC SoM DTSI [0] hence deleting
the disabled node from RZ/Five SMARC SoM DTSI enables it here too as we
include [0] in RZ/Five SMARC SoM DTSI.
[0] arch/arm64/boot/dts/renesas/rzg2ul-smarc-som.dtsi
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20221118135715.14410-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
