Add status power led node for StarFive VisionFive2 and variant boards.
Signed-off-by: E Shattow <e@freeshell.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add bootph-pre-ram hinting to jh7110-common.dtsi:
- i2c5_pins and i2c-pins subnode for connection to eeprom
- eeprom node
- qspi flash configuration subnode
- memory node
- mmc0 for eMMC
- mmc1 for SD Card
- uart0 for serial console
With this the U-Boot SPL secondary program loader may drop such overrides.
Signed-off-by: E Shattow <e@freeshell.de>
Acked-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
StarFive VisionFive2 and similar JH7110 boards have an eeprom compatible
with Atmel 24c04. Add the node so this may be used with the at24 driver.
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Use qspi flash read-delay and spi-max-frequency settings compatible with
U-Boot bootloader.
Observations from testing on Pine64 Star64 hardware within U-Boot bootloader
and read-delay=2 are spi-max-frequency less than 49.8MHz fails to write,
corrupt data writes at 25MHz to 49.799999MHz, and valid data writes at
49.8MHz to 100MHz (not tested above 100MHz). No valid spi-max-frequency
was found for 1<read-delay<=3 and corrupt data with read-delay=3.
Looking around the Linux codebase it is common to see read-delay 2 cycles
with spi-max-frequency 100MHz and testing confirms this to work in both
U-Boot and Linux.
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Acked-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add syscrg clock assignments for CPU, BUS, PERH, and QSPI as required by
boot loader before kernel.
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The pin names of MMC0 pinmux is defined in the pinctrl dt binding header
associated with starfive,jh7110-pinctrl .
Include the header file and use these names instead of raw numbers for
defining MMC0 pinmux.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The jh7110 boards do not have a Rohm DAC on them as far as I
can tell, and they certainly do not have a dh2228fv, as this device does
not actually exist! Remove the dac nodes from the devicetrees as it is
not acceptable to pretend to have a device on a board in order to bind
the spidev driver in Linux.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Currently, there are 3 regulators defined in JH7110's common device tree,
but regulator names are mixed with "-" and "_". So unify them to "_",
which is more often to be seen in other dts files.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Acked-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
This release adds the devicetree files for an impressive number of new
SoC variants, though as expected these are all related to others we
already support:
- The microchip sam9x7 devicetree is now added, after the device driver
and platform code has already made it in. This is likely the last ARMv5
(!) platform to ever get added, updating the 20+ year old at91/sam9
platform wtih DDR3 memory and gigabit ethernet.
- On the Apple platform, there are now devicetree files for a number of
A-series SoCs in addition to the M-series ones, these are used
primarily in phones and tablets, but are closely related to the
already supported chips.
- Samsung Exynos 8895 and Exynos 990 are more phone SoCs used in older
Samsung Galaxy phones.
- Qualcomm Snapdragon 778G (SM7325) is another phone SoC, closely related
to the Snapdragon 7c+ Gen 3 (SC7280) used in low-end laptops.
- Rockchip RK3528 and RK3576 are new variants of their TV box and Tablet
chips, still using the older ARMv8.0 cores from RK3328/RK3399 but
with a newer process and other improvements from the RK35xx (otherwise
ARMv8.2) chips. RK3566T and RK3399-S are also added, these are just
lower-cost versions of their normal counterparts.
- TI J742S2 is a feature-reduced version of the J784s4
industrial/automotive SoC, with fewer CPU cores.
- Sophgo SG2002 is an embedded SoC with one RISC-V (C906) and one ARM
(Cortex-A53) core, at this point support is only added for running
on the RISC-V side on the LicheeRV Nano board.
A total of 92 new .dts files describing individual machines is added,
which must be a new record. The majority of these is for the newly added
chips above, notably all the Apple phones and tablets. The other new
machines include nine industrial/embedded boards with NXP i.MX6 or i.MX8
SoCs, eight for Rockchips RK35XX and one or two each for Rockchips RV1109,
RK3308, Allwinner A33, Tegra 234, Qualcomm qcs9100/sc8280xp/x1e80100,
TI AM625 and Starfive JH7110.
As usual there are also many newlyad added features in existing boards
as well as cleanups and minor bugfixes.
-----BEGIN PGP SIGNATURE-----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=Ha1w
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC devicetree updates from Arnd Bergmann:
"This release adds the devicetree files for an impressive number of new
SoC variants, though as expected these are all related to others we
already support:
- The microchip sam9x7 devicetree is now added, after the device
driver and platform code has already made it in. This is likely the
last ARMv5 (!) platform to ever get added, updating the 20+ year
old at91/sam9 platform with DDR3 memory and gigabit ethernet.
- On the Apple platform, there are now devicetree files for a number
of A-series SoCs in addition to the M-series ones, these are used
primarily in phones and tablets, but are closely related to the
already supported chips.
- Samsung Exynos 8895 and Exynos 990 are more phone SoCs used in
older Samsung Galaxy phones.
- Qualcomm Snapdragon 778G (SM7325) is another phone SoC, closely
related to the Snapdragon 7c+ Gen 3 (SC7280) used in low-end
laptops.
- Rockchip RK3528 and RK3576 are new variants of their TV box and
Tablet chips, still using the older ARMv8.0 cores from
RK3328/RK3399 but with a newer process and other improvements from
the RK35xx (otherwise ARMv8.2) chips. RK3566T and RK3399-S are also
added, these are just lower-cost versions of their normal
counterparts.
- TI J742S2 is a feature-reduced version of the J784s4
industrial/automotive SoC, with fewer CPU cores.
- Sophgo SG2002 is an embedded SoC with one RISC-V (C906) and one ARM
(Cortex-A53) core, at this point support is only added for running
on the RISC-V side on the LicheeRV Nano board.
A total of 92 new .dts files describing individual machines is added,
which must be a new record. The majority of these is for the newly
added chips above, notably all the Apple phones and tablets. The other
new machines include nine industrial/embedded boards with NXP i.MX6 or
i.MX8 SoCs, eight for Rockchips RK35XX and one or two each for
Rockchips RV1109, RK3308, Allwinner A33, Tegra 234, Qualcomm
qcs9100/sc8280xp/x1e80100, TI AM625 and Starfive JH7110.
As usual there are also many newly added features in existing boards
as well as cleanups and minor bugfixes"
* tag 'soc-dt-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (718 commits)
arm64: dts: apm: Remove unused and undocumented "bus_num" property
arm: dts: spear13xx: Remove unused and undocumented "pl022,slave-tx-disable" property
arm64: dts: amd: Remove unused and undocumented "amd,zlib-support" property
arm64: dts: lg131x: Update spi clock properties
arm64: dts: seattle: Update spi clock properties
arm64: dts: rockchip: use less broad pinctrl for pcie3x1 on Radxa E25
arm64: dts: rockchip: add Radxa ROCK 5C
dt-bindings: arm: rockchip: add Radxa ROCK 5C
arm64: dts: rockchip: orangepi-5-plus: Enable GPU
arm64: dts: rockchip: enable USB3 on NanoPC-T6
arm64: dts: rockchip: adapt regulator nodenames to preferred form
arm64: dts: rockchip: Enable HDMI display for rk3588 Cool Pi GenBook
arm64: dts: rockchip: Enable HDMI display for rk3588 Cool Pi 4B
arm64: dts: rockchip: Enable HDMI0 for rk3588 Cool Pi CM5 EVB
arm64: dts: rockchip: Enable HDMI on NanoPi R6C/R6S
arm64: dts: rockchip: Enable GPU on NanoPi R6C/R6S
arm64: dts: rockchip: Enable HDMI on Hardkernel ODROID-M2
arm64: dts: rockchip: Remove non-removable flag from sdmmc on rk3576-sige5
arm64: dts: allwinner: a100: perf1: Add eMMC and MMC node
arm64: dts: allwinner: pinephone: Add mount matrix to accelerometer
...
The JH7110 USB0 can operate as a dual-role USB device. Different
boards can have different configuration.
For all current boards this device operates in peripheral mode, but
on a new board this operates in host mode. This property will no
longer be common, so define the "dr_mode" property in the board files
rather than in the common DTSI file.
Signed-off-by: Alex Elder <elder@riscstar.com>
Signed-off-by: Guodong Xu <guodong@riscstar.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Earlier this year a new DTSI file was created to define common
properties for the StarFive VisionFive 2 and Milk-V Mars boards,
both of which use the StarFive JH7110 SoC. The Pine64 Star64
board has also been added since that time.
Some of the nodes defined in "jh7110-common.dtsi" are enabled in
that file because all of the boards including it "want" them
enabled.
An upcoming patch enables another JH7110 board, but for that
board not all of these common nodes should be enabled. Prepare
for supporting the new board by avoiding enabling these nodes in
"jh7110-common.dtsi", and enable them instead in these files:
jh7110-milkv-mars.dts
jh7110-pine64-star64.dts
jh7110-starfive-visionfive-2.dtsi
Signed-off-by: Alex Elder <elder@riscstar.com>
Signed-off-by: Guodong Xu <guodong@riscstar.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Aurelien reported probe failures due to the csi node being enabled
without having a camera attached to it. A camera was in the initial
submissions, but was removed from the dts, as it had not actually been
present on the board, but was from an addon board used by the
developer of the relevant drivers. The non-camera pipeline nodes were
not disabled when this happened and the probe failures are problematic
for Debian. Disable them.
CC: stable@vger.kernel.org
Fixes: 28ecaaa5af ("riscv: dts: starfive: jh7110: Add camera subsystem nodes")
Closes: https://lore.kernel.org/all/Zw1-vcN4CoVkfLjU@aurel32.net/
Reported-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
CPUfreq supports 4 cpu frequency loads on 375/500/750/1500MHz.
But now PLL0 rate is 1GHz and the cpu frequency loads become
250/333/500/1000MHz in fact.
The PLL0 rate should be default set to 1.5GHz and set the
cpu_core rate to 500MHz in safe.
Fixes: e2c510d6d6 ("riscv: dts: starfive: Add cpu scaling for JH7110 SoC")
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The devicetree updates are fairly well spread out across platforms,
with Qualcomm making up about a third of the total.
There are three new SoCs in existing product families this:
- NXP i.MX95 is a variant of i.MX93, now with six Cortex-A55 cores
instead of just two as well as a GPU and more high-speed I/O
devices.
- Qualcomm QCS8550 is a variant of SM8550 for IOT devices
- Airoha EN7581 is a 10G-PON network chip and related to
the MT7981 Wireless router chip from its parent Mediatek.
In total there are 58 new machines, including four riscv
boards and eight for 32-bit arm.
The most exciting new addition is probably a pair of laptops
based on the Qualcomm x1e80100 (Snapdragon X1 Elite) chip,
the Asus Vivobook S15 and the Lenovo Yoga Slim7x.
Other noteworthy new additions are:
- A total of 20 Qualcomm based machines, mostly Android devices
from Samsung, Motorola and LG, as well as a wireless router
and some reference designs
- Six NXP i.MX based machines, mostly industrial boards along
with some reference designs
- Mediatek sees some interesting Filogic based routers
including the "OpenWRT One", a few new Chromebooks as
well as single-board computers.
- Four machines from Solidrun based on Marvell cn913x,
replacing the older Armada 8000 based counterparts
- The four Amlogic machines are all set top boxes or reference
designs for them
- The nine new Rockchips machines are mostly single-board
computers including some interesting ones based on the
rk3588 chip like the ROCK 5 ITX board and the CM3588
with its four NVMe slots
- The RISC-V boards are all single-board computers based on
Starfive JH7110, Microchip MPFS and Allwinner D1, which all
had similar boards already
There are also a lot of updates to already supported machines,
notably for the TI K3, Rockchips, Freescale and of course
Qualcomm platforms.
-----BEGIN PGP SIGNATURE-----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=xGqj
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC dt updates from Arnd Bergmann:
"The devicetree updates are fairly well spread out across platforms,
with Qualcomm making up about a third of the total.
There are three new SoCs in existing product families this:
- NXP i.MX95 is a variant of i.MX93, now with six Cortex-A55 cores
instead of just two as well as a GPU and more high-speed I/O
devices.
- Qualcomm QCS8550 is a variant of SM8550 for IOT devices
- Airoha EN7581 is a 10G-PON network chip and related to the MT7981
Wireless router chip from its parent Mediatek.
In total there are 58 new machines, including four riscv boards and
eight for 32-bit arm.
The most exciting new addition is probably a pair of laptops based on
the Qualcomm x1e80100 (Snapdragon X1 Elite) chip, the Asus Vivobook
S15 and the Lenovo Yoga Slim7x.
Other noteworthy new additions are:
- A total of 20 Qualcomm based machines, mostly Android devices from
Samsung, Motorola and LG, as well as a wireless router and some
reference designs
- Six NXP i.MX based machines, mostly industrial boards along with
some reference designs
- Mediatek sees some interesting Filogic based routers including the
"OpenWRT One", a few new Chromebooks as well as single-board
computers.
- Four machines from Solidrun based on Marvell cn913x, replacing the
older Armada 8000 based counterparts
- The four Amlogic machines are all set top boxes or reference
designs for them
- The nine new Rockchips machines are mostly single-board computers
including some interesting ones based on the rk3588 chip like the
ROCK 5 ITX board and the CM3588 with its four NVMe slots
- The RISC-V boards are all single-board computers based on Starfive
JH7110, Microchip MPFS and Allwinner D1, which all had similar
boards already
There are also a lot of updates to already supported machines, notably
for the TI K3, Rockchips, Freescale and of course Qualcomm platforms"
* tag 'soc-dt-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (846 commits)
arm64: dts: allwinner: h616: add crypto engine node
riscv: dts: add clock generator for Sophgo SG2042 SoC
arm64: dts: rockchip: Add Xunlong Orange Pi 3B
dt-bindings: arm: rockchip: Add Xunlong Orange Pi 3B
arm64: dts: rockchip: Add Radxa ROCK 3B
dt-bindings: arm: rockchip: Add Radxa ROCK 3B
mailmap: Update Luca Weiss's email address
ARM: dts: ixp4xx: nslu2: beeper uses PWM
arm64: dts: rockchip: add ROCK 5 ITX board
dt-bindings: arm: rockchip: Add ROCK 5 ITX board
arm64: dts: rockchip: Add dma-names to uart1 on Pine64 rk3566 devices
arm64: dts: rockchip: Add avdd supplies to hdmi on rock64
arm64: dts: qcom: msm8916-lg-c50: add initial dts for LG Leon LTE
arm64: dts: qcom: msm8916-lg-m216: Add initial device tree
dt-bindings: arm: qcom: Add msm8916 based LG devices
ARM: dts: qcom: msm8960: correct memory base
arm64: dts: qcom: ipq9574: Add icc provider ability to gcc
dt-bindings: interconnect: Add Qualcomm IPQ9574 support
arm64: dts: qcom: sm8150: Add video clock controller node
arm64: dts: qcom: pm6150: Add vibrator
...
Add PCIe dts configuraion for JH7110 SoC platform. The Star64 only has
one exposed PCIe port, so only the Mars and VisionFive 2 get two
enabled.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
[conor: squash in star64's single exposed port]
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Currently, for JH7110 boards with EMMC slot, vqmmc voltage for EMMC is
fixed to 1.8V, while the spec needs it to be 3.3V on low speed mode and
should support switching to 1.8V when using higher speed mode. Since
there are no other peripherals using the same voltage source of EMMC's
vqmmc(ALDO4) on every board currently supported by mainline kernel,
regulator-max-microvolt of ALDO4 should be set to 3.3V.
Cc: stable@vger.kernel.org
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Fixes: 7dafcfa79c ("riscv: dts: starfive: enable DCDC1&ALDO4 node in axp15060")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Up to now, the describe flash partition layout has some gaps.
Use the whole flash chip by getting rid of the gaps.
Suggested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
This is to prepare for Milkv Mars board dts support in the following
patch. Let's factored out common part into .dtsi.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
