Add status power led node for StarFive VisionFive2 and variant boards.
Signed-off-by: E Shattow <e@freeshell.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Improve style with node property order sort of common properties before
vendor prefixes
Signed-off-by: E Shattow <e@freeshell.de>
Acked-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add bootph-pre-ram hinting to jh7110-common.dtsi:
- i2c5_pins and i2c-pins subnode for connection to eeprom
- eeprom node
- qspi flash configuration subnode
- memory node
- mmc0 for eMMC
- mmc1 for SD Card
- uart0 for serial console
With this the U-Boot SPL secondary program loader may drop such overrides.
Signed-off-by: E Shattow <e@freeshell.de>
Acked-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
StarFive VisionFive2 and similar JH7110 boards have an eeprom compatible
with Atmel 24c04. Add the node so this may be used with the at24 driver.
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Use qspi flash read-delay and spi-max-frequency settings compatible with
U-Boot bootloader.
Observations from testing on Pine64 Star64 hardware within U-Boot bootloader
and read-delay=2 are spi-max-frequency less than 49.8MHz fails to write,
corrupt data writes at 25MHz to 49.799999MHz, and valid data writes at
49.8MHz to 100MHz (not tested above 100MHz). No valid spi-max-frequency
was found for 1<read-delay<=3 and corrupt data with read-delay=3.
Looking around the Linux codebase it is common to see read-delay 2 cycles
with spi-max-frequency 100MHz and testing confirms this to work in both
U-Boot and Linux.
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Acked-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add syscrg clock assignments for CPU, BUS, PERH, and QSPI as required by
boot loader before kernel.
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The pin names of MMC0 pinmux is defined in the pinctrl dt binding header
associated with starfive,jh7110-pinctrl .
Include the header file and use these names instead of raw numbers for
defining MMC0 pinmux.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add usb_cdns3 and usb0_pins configuration to support super speed USB
device on the FML13V01 board.
Signed-off-by: Sandie Cao <sandie.cao@deepcomputing.io>
Tested-by: Maud Spierings <maud_spierings@hotmail.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
There is new support for additional on-chip devices on Apple, Mediatek,
Renesas, Rockchip, Samsung, Google, TI, ST, Nvidia and Amlogic devices.
The Arm Morello reference platform gets a devicetree for booting in
normal aarch64 mode. The hardware supports experimental CHERI support,
which requires a modified kernel.
The AMD (formerly Xilinx) Versal NET SoC gets added, this is a combined
FPGA with Cortex-A78 CPUs in a SoC.
Six new ST STM32MP2 SoC variants are added. Like the earlier STM32MP25,
the MP211, MP213, MP215, MP231, MP233 and MP235 models are based on one
or two Cortex-A35 cores but each feature a different set of I/O devices.
Mediatek MT8370 is a minor variation of MT8390 with fewer CPU and
GPU cores
Apple T2 is the baseboard management controller on earlier Intel CPU
based Macs, with 16 models now gaining initial support.
All the above come with dts files for the reference boards. In
addition, these boards are added for the SoCs that are already supported.
- The Milk-V Jupiter board based on SpacemiT K1/M1
- NetCube Systems Kumquat board based on the 32-bit Allwinner V3s SoC
- Three boards based on 32-bit stm32mp1
- 11 distinct board variants from Toradex and one from Variscite,
all based on i.MX6
- Google Pixel Pro 6 phone based on gs101 (Tensor)
- Three additional variants of the i.MX8MP based "Skov" board
- A second variant of the i.MX95 EVK board
- Two boards based on Renesas SoCs
- Four boards based the Rockchip RK35xx series, plus the RK3588
"MNT Reform 2" laptop
-----BEGIN PGP SIGNATURE-----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=6ZZ6
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC devicetree updates from Arnd Bergmann:
"There is new support for additional on-chip devices on Apple,
Mediatek, Renesas, Rockchip, Samsung, Google, TI, ST, Nvidia and
Amlogic devices.
The Arm Morello reference platform gets a devicetree for booting in
normal aarch64 mode. The hardware supports experimental CHERI support,
which requires a modified kernel.
The AMD (formerly Xilinx) Versal NET SoC gets added, this is a
combined FPGA with Cortex-A78 CPUs in a SoC.
Six new ST STM32MP2 SoC variants are added. Like the earlier
STM32MP25, the MP211, MP213, MP215, MP231, MP233 and MP235 models are
based on one or two Cortex-A35 cores but each feature a different set
of I/O devices.
Mediatek MT8370 is a minor variation of MT8390 with fewer CPU and GPU
cores
Apple T2 is the baseboard management controller on earlier Intel CPU
based Macs, with 16 models now gaining initial support.
All the above come with dts files for the reference boards. In
addition, these boards are added for the SoCs that are already
supported:
- The Milk-V Jupiter board based on SpacemiT K1/M1
- NetCube Systems Kumquat board based on the 32-bit Allwinner V3s SoC
- Three boards based on 32-bit stm32mp1
- 11 distinct board variants from Toradex and one from Variscite, all
based on i.MX6
- Google Pixel Pro 6 phone based on gs101 (Tensor)
- Three additional variants of the i.MX8MP based "Skov" board
- A second variant of the i.MX95 EVK board
- Two boards based on Renesas SoCs
- Four boards based the Rockchip RK35xx series, plus the RK3588 'MNT
Reform 2' laptop"
* tag 'soc-dt-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (538 commits)
arm64: dts: Add gpio_intc node for Amlogic A5 SoCs
arm64: dts: Add gpio_intc node for Amlogic A4 SoCs
arm64: dts: hi3660: Add property for fixing CPUIdle
arm64: dts: rockchip: remove ethm0_clk0_25m_out from Sige5 gmac0
arm64: dts: marvell: Use preferred node names for "simple-bus"
arm64: dts: marvell: Drop unused CP11X_TYPE define
arm64: dts: marvell: Move arch timer and pmu nodes to top-level
arm64: dts: rockchip: Fix PWM pinctrl names
arm64: dts: rockchip: fix RK3576 SCMI clock IDs
dt-bindings: clock: rk3576: add SCMI clocks
arm64: dts: rockchip: Fix pcie reset gpio on Orange Pi 5 Max
arm64: dts: amd/seattle: Drop undocumented "spi-controller" properties
arm64: dts: amd/seattle: Fix bus, mmc, and ethernet node names
arm64: dts: amd/seattle: Move and simplify fixed clocks
arm64: dts: amd/seattle: Base Overdrive B1 on top of B0 version
arm64: dts: rockchip: Enable HDMI audio output for ArmSoM Sige7
arm64: dts: rockchip: Enable onboard eMMC on Radxa E20C
arm64: dts: rockchip: Add SDHCI controller for RK3528
arm64: dts: rockchip: Remove bluetooth node from rock-3a
arm64: dts: rockchip: Move rk356x scmi SHMEM to reserved memory
...
Cross-merge networking fixes after downstream PR (net-6.14-rc8).
Conflict:
tools/testing/selftests/net/Makefile
03544faad7 ("selftest: net: add proc_net_pktgen")
3ed61b8938 ("selftests: net: test for lwtunnel dst ref loops")
tools/testing/selftests/net/config:
85cb3711ac ("selftests: net: Add test cases for link and peer netns")
3ed61b8938 ("selftests: net: test for lwtunnel dst ref loops")
Adjacent commits:
tools/testing/selftests/net/Makefile
c935af429e ("selftests: net: add support for testing SO_RCVMARK and SO_RCVPRIORITY")
355d940f4d ("Revert "selftests: Add IPv6 link-local address generation tests for GRE devices."")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Whether the MII transmit clock can be stopped is primarily a property
of the PHY (there is a capability bit that should be checked first.)
Whether the MAC is capable of stopping the transmit clock is a separate
issue, but this is already handled by the core DesignWare MAC code.
As commit "net: stmmac: starfive: use PHY capability for TX clock stop"
adds the flag to use the PHY capability, remove the DT property that is
now unecessary.
Cc: Samin Guo <samin.guo@starfivetech.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tsIU5-005vGR-4c@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
One of four USB-A ports on the Pine64 Star64 is USB 3.0 which requires to
disable PCIE0 and change the mode of PCIE0 PHY to USB3.0 operation. The
remaining three USB-A ports are USB 2.0 with the USB0 PHY and do not
conflict with any of PCIE0 or PCIE1. PCIE1 (1-lane) routes to a PCIe X4
connector.
Signed-off-by: E Shattow <e@freeshell.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
StarFive JH7110 contains a Cadence USB2.0+USB3.0 controller IP block that
may exclusively use pciephy0 for USB3.0 connectivity. Add the register
offsets for the driver to enable/disable USB3.0 on pciephy0.
Signed-off-by: E Shattow <e@freeshell.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Starfive Soc common defines GPIO28 as pcie1 reset, GPIO21 as pcie1 wakeup;
But the FML13V01 board uses GPIO21 as pcie1 reset, GPIO28 as pcie1 wakeup;
redefine pcie1 gpio and enable pcie1 for pcie based Wi-Fi.
Signed-off-by: Sandie Cao <sandie.cao@deepcomputing.io>
Tested-by: Maud Spierings <maud_spierings@hotmail.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The jh7110 boards do not have a Rohm DAC on them as far as I
can tell, and they certainly do not have a dh2228fv, as this device does
not actually exist! Remove the dac nodes from the devicetrees as it is
not acceptable to pretend to have a device on a board in order to bind
the spidev driver in Linux.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Currently, there are 3 regulators defined in JH7110's common device tree,
but regulator names are mixed with "-" and "_". So unify them to "_",
which is more often to be seen in other dts files.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Acked-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Milk-V Mars board routes one of four USB-A ports to USB0 on the SoC
rather than to the VL805 USB 3.0 <-> PCIe chip.
Set JH7110 on-chip USB host mode and vbus pin assignment accordingly.
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: E Shattow <e@freeshell.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Pine64 Star64 board routes all four USB-A ports to USB0 on the SoC.
Set JH7110 on-chip USB host mode and vbus pin assignment accordingly.
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
This release adds the devicetree files for an impressive number of new
SoC variants, though as expected these are all related to others we
already support:
- The microchip sam9x7 devicetree is now added, after the device driver
and platform code has already made it in. This is likely the last ARMv5
(!) platform to ever get added, updating the 20+ year old at91/sam9
platform wtih DDR3 memory and gigabit ethernet.
- On the Apple platform, there are now devicetree files for a number of
A-series SoCs in addition to the M-series ones, these are used
primarily in phones and tablets, but are closely related to the
already supported chips.
- Samsung Exynos 8895 and Exynos 990 are more phone SoCs used in older
Samsung Galaxy phones.
- Qualcomm Snapdragon 778G (SM7325) is another phone SoC, closely related
to the Snapdragon 7c+ Gen 3 (SC7280) used in low-end laptops.
- Rockchip RK3528 and RK3576 are new variants of their TV box and Tablet
chips, still using the older ARMv8.0 cores from RK3328/RK3399 but
with a newer process and other improvements from the RK35xx (otherwise
ARMv8.2) chips. RK3566T and RK3399-S are also added, these are just
lower-cost versions of their normal counterparts.
- TI J742S2 is a feature-reduced version of the J784s4
industrial/automotive SoC, with fewer CPU cores.
- Sophgo SG2002 is an embedded SoC with one RISC-V (C906) and one ARM
(Cortex-A53) core, at this point support is only added for running
on the RISC-V side on the LicheeRV Nano board.
A total of 92 new .dts files describing individual machines is added,
which must be a new record. The majority of these is for the newly added
chips above, notably all the Apple phones and tablets. The other new
machines include nine industrial/embedded boards with NXP i.MX6 or i.MX8
SoCs, eight for Rockchips RK35XX and one or two each for Rockchips RV1109,
RK3308, Allwinner A33, Tegra 234, Qualcomm qcs9100/sc8280xp/x1e80100,
TI AM625 and Starfive JH7110.
As usual there are also many newlyad added features in existing boards
as well as cleanups and minor bugfixes.
-----BEGIN PGP SIGNATURE-----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=Ha1w
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC devicetree updates from Arnd Bergmann:
"This release adds the devicetree files for an impressive number of new
SoC variants, though as expected these are all related to others we
already support:
- The microchip sam9x7 devicetree is now added, after the device
driver and platform code has already made it in. This is likely the
last ARMv5 (!) platform to ever get added, updating the 20+ year
old at91/sam9 platform with DDR3 memory and gigabit ethernet.
- On the Apple platform, there are now devicetree files for a number
of A-series SoCs in addition to the M-series ones, these are used
primarily in phones and tablets, but are closely related to the
already supported chips.
- Samsung Exynos 8895 and Exynos 990 are more phone SoCs used in
older Samsung Galaxy phones.
- Qualcomm Snapdragon 778G (SM7325) is another phone SoC, closely
related to the Snapdragon 7c+ Gen 3 (SC7280) used in low-end
laptops.
- Rockchip RK3528 and RK3576 are new variants of their TV box and
Tablet chips, still using the older ARMv8.0 cores from
RK3328/RK3399 but with a newer process and other improvements from
the RK35xx (otherwise ARMv8.2) chips. RK3566T and RK3399-S are also
added, these are just lower-cost versions of their normal
counterparts.
- TI J742S2 is a feature-reduced version of the J784s4
industrial/automotive SoC, with fewer CPU cores.
- Sophgo SG2002 is an embedded SoC with one RISC-V (C906) and one ARM
(Cortex-A53) core, at this point support is only added for running
on the RISC-V side on the LicheeRV Nano board.
A total of 92 new .dts files describing individual machines is added,
which must be a new record. The majority of these is for the newly
added chips above, notably all the Apple phones and tablets. The other
new machines include nine industrial/embedded boards with NXP i.MX6 or
i.MX8 SoCs, eight for Rockchips RK35XX and one or two each for
Rockchips RV1109, RK3308, Allwinner A33, Tegra 234, Qualcomm
qcs9100/sc8280xp/x1e80100, TI AM625 and Starfive JH7110.
As usual there are also many newly added features in existing boards
as well as cleanups and minor bugfixes"
* tag 'soc-dt-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (718 commits)
arm64: dts: apm: Remove unused and undocumented "bus_num" property
arm: dts: spear13xx: Remove unused and undocumented "pl022,slave-tx-disable" property
arm64: dts: amd: Remove unused and undocumented "amd,zlib-support" property
arm64: dts: lg131x: Update spi clock properties
arm64: dts: seattle: Update spi clock properties
arm64: dts: rockchip: use less broad pinctrl for pcie3x1 on Radxa E25
arm64: dts: rockchip: add Radxa ROCK 5C
dt-bindings: arm: rockchip: add Radxa ROCK 5C
arm64: dts: rockchip: orangepi-5-plus: Enable GPU
arm64: dts: rockchip: enable USB3 on NanoPC-T6
arm64: dts: rockchip: adapt regulator nodenames to preferred form
arm64: dts: rockchip: Enable HDMI display for rk3588 Cool Pi GenBook
arm64: dts: rockchip: Enable HDMI display for rk3588 Cool Pi 4B
arm64: dts: rockchip: Enable HDMI0 for rk3588 Cool Pi CM5 EVB
arm64: dts: rockchip: Enable HDMI on NanoPi R6C/R6S
arm64: dts: rockchip: Enable GPU on NanoPi R6C/R6S
arm64: dts: rockchip: Enable HDMI on Hardkernel ODROID-M2
arm64: dts: rockchip: Remove non-removable flag from sdmmc on rk3576-sige5
arm64: dts: allwinner: a100: perf1: Add eMMC and MMC node
arm64: dts: allwinner: pinephone: Add mount matrix to accelerometer
...
The FML13V01 board from DeepComputing incorporates a StarFive JH7110 SoC.
It is a mainboard designed for the Framework Laptop 13 Chassis, which has
(Framework) SKU FRANHQ0001.
The FML13V01 board features:
- StarFive JH7110 SoC
- LPDDR4 8GB
- eMMC 32GB or 128GB
- QSPI Flash
- MicroSD Slot
- PCIe-based Wi-Fi
- 4 USB-C Ports
- Port 1: PD 3.0 (60W Max), USB 3.2 Gen 1, DP 1.4 (4K@30Hz/2.5K@60Hz)
- Port 2: PD 3.0 (60W Max), USB 3.2 Gen 1
- Port 3 & 4: USB 3.2 Gen 1
Create the DTS file for the DeepComputing FML13V01 board. Based on
'jh7110-common.dtsi', usb0 is enabled and is set to operate as a "host".
Signed-off-by: Sandie Cao <sandie.cao@deepcomputing.io>
[elder@riscstar.com: revised the description, updated some nodes]
Signed-off-by: Alex Elder <elder@riscstar.com>
Signed-off-by: Guodong Xu <guodong@riscstar.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The JH7110 USB0 can operate as a dual-role USB device. Different
boards can have different configuration.
For all current boards this device operates in peripheral mode, but
on a new board this operates in host mode. This property will no
longer be common, so define the "dr_mode" property in the board files
rather than in the common DTSI file.
Signed-off-by: Alex Elder <elder@riscstar.com>
Signed-off-by: Guodong Xu <guodong@riscstar.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Earlier this year a new DTSI file was created to define common
properties for the StarFive VisionFive 2 and Milk-V Mars boards,
both of which use the StarFive JH7110 SoC. The Pine64 Star64
board has also been added since that time.
Some of the nodes defined in "jh7110-common.dtsi" are enabled in
that file because all of the boards including it "want" them
enabled.
An upcoming patch enables another JH7110 board, but for that
board not all of these common nodes should be enabled. Prepare
for supporting the new board by avoiding enabling these nodes in
"jh7110-common.dtsi", and enable them instead in these files:
jh7110-milkv-mars.dts
jh7110-pine64-star64.dts
jh7110-starfive-visionfive-2.dtsi
Signed-off-by: Alex Elder <elder@riscstar.com>
Signed-off-by: Guodong Xu <guodong@riscstar.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Aurelien reported probe failures due to the csi node being enabled
without having a camera attached to it. A camera was in the initial
submissions, but was removed from the dts, as it had not actually been
present on the board, but was from an addon board used by the
developer of the relevant drivers. The non-camera pipeline nodes were
not disabled when this happened and the probe failures are problematic
for Debian. Disable them.
CC: stable@vger.kernel.org
Fixes: 28ecaaa5af ("riscv: dts: starfive: jh7110: Add camera subsystem nodes")
Closes: https://lore.kernel.org/all/Zw1-vcN4CoVkfLjU@aurel32.net/
Reported-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
CPUfreq supports 4 cpu frequency loads on 375/500/750/1500MHz.
But now PLL0 rate is 1GHz and the cpu frequency loads become
250/333/500/1000MHz in fact.
The PLL0 rate should be default set to 1.5GHz and set the
cpu_core rate to 500MHz in safe.
Fixes: e2c510d6d6 ("riscv: dts: starfive: Add cpu scaling for JH7110 SoC")
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Here is a small set of tty and serial driver updates for 6.11-rc1. Not
much happened this cycle, unlike the previous kernel release which had
lots of "excitement" in this part of the kernel. Included in here are
the following changes:
- dt binding updates for new platforms
- 8250 driver updates
- various small serial driver fixes and updates
- printk/console naming and matching attempt #2 (was reverted for
6.10-final, should be good to go this time around, acked by the
relevant maintainers).
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZppbCQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymV1ACeIY5kgipqY7w4d3/7PcpKMiftrisAn0hr6csj
Gan+k3cuVGlasGkaQ5/B
=35VK
-----END PGP SIGNATURE-----
Merge tag 'tty-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is a small set of tty and serial driver updates for 6.11-rc1. Not
much happened this cycle, unlike the previous kernel release which had
lots of "excitement" in this part of the kernel. Included in here are
the following changes:
- dt binding updates for new platforms
- 8250 driver updates
- various small serial driver fixes and updates
- printk/console naming and matching attempt #2 (was reverted for
6.10-final, should be good to go this time around, acked by the
relevant maintainers).
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (22 commits)
Documentation: kernel-parameters: Add DEVNAME:0.0 format for serial ports
serial: core: Add serial_base_match_and_update_preferred_console()
printk: Add match_devname_and_update_preferred_console()
serial: sc16is7xx: hardware reset chip if reset-gpios is defined in DT
dt-bindings: serial: sc16is7xx: add reset-gpios
dt-bindings: serial: vt8500-uart: convert to json-schema
serial: 8250_platform: Explicitly show we initialise ISA ports only once
tty: add missing MODULE_DESCRIPTION() macros
dt-bindings: serial: mediatek,uart: add MT7988
serial: sh-sci: Add support for RZ/V2H(P) SoC
dt-bindings: serial: Add documentation for Renesas RZ/V2H(P) (R9A09G057) SCIF support
dt-bindings: serial: renesas,scif: Make 'interrupt-names' property as required
dt-bindings: serial: renesas,scif: Validate 'interrupts' and 'interrupt-names'
dt-bindings: serial: renesas,scif: Move ref for serial.yaml at the end
riscv: dts: starfive: jh7110: Add the core reset and jh7110 compatible for uarts
serial: 8250_dw: Use reset array API to get resets
dt-bindings: serial: snps-dw-apb-uart: Add one more reset signal for StarFive JH7110 SoC
serial: 8250: Extract platform driver
serial: 8250: Extract RSA bits
serial: imx: stop casting struct uart_port to struct imx_port
...
The devicetree updates are fairly well spread out across platforms,
with Qualcomm making up about a third of the total.
There are three new SoCs in existing product families this:
- NXP i.MX95 is a variant of i.MX93, now with six Cortex-A55 cores
instead of just two as well as a GPU and more high-speed I/O
devices.
- Qualcomm QCS8550 is a variant of SM8550 for IOT devices
- Airoha EN7581 is a 10G-PON network chip and related to
the MT7981 Wireless router chip from its parent Mediatek.
In total there are 58 new machines, including four riscv
boards and eight for 32-bit arm.
The most exciting new addition is probably a pair of laptops
based on the Qualcomm x1e80100 (Snapdragon X1 Elite) chip,
the Asus Vivobook S15 and the Lenovo Yoga Slim7x.
Other noteworthy new additions are:
- A total of 20 Qualcomm based machines, mostly Android devices
from Samsung, Motorola and LG, as well as a wireless router
and some reference designs
- Six NXP i.MX based machines, mostly industrial boards along
with some reference designs
- Mediatek sees some interesting Filogic based routers
including the "OpenWRT One", a few new Chromebooks as
well as single-board computers.
- Four machines from Solidrun based on Marvell cn913x,
replacing the older Armada 8000 based counterparts
- The four Amlogic machines are all set top boxes or reference
designs for them
- The nine new Rockchips machines are mostly single-board
computers including some interesting ones based on the
rk3588 chip like the ROCK 5 ITX board and the CM3588
with its four NVMe slots
- The RISC-V boards are all single-board computers based on
Starfive JH7110, Microchip MPFS and Allwinner D1, which all
had similar boards already
There are also a lot of updates to already supported machines,
notably for the TI K3, Rockchips, Freescale and of course
Qualcomm platforms.
-----BEGIN PGP SIGNATURE-----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=xGqj
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC dt updates from Arnd Bergmann:
"The devicetree updates are fairly well spread out across platforms,
with Qualcomm making up about a third of the total.
There are three new SoCs in existing product families this:
- NXP i.MX95 is a variant of i.MX93, now with six Cortex-A55 cores
instead of just two as well as a GPU and more high-speed I/O
devices.
- Qualcomm QCS8550 is a variant of SM8550 for IOT devices
- Airoha EN7581 is a 10G-PON network chip and related to the MT7981
Wireless router chip from its parent Mediatek.
In total there are 58 new machines, including four riscv boards and
eight for 32-bit arm.
The most exciting new addition is probably a pair of laptops based on
the Qualcomm x1e80100 (Snapdragon X1 Elite) chip, the Asus Vivobook
S15 and the Lenovo Yoga Slim7x.
Other noteworthy new additions are:
- A total of 20 Qualcomm based machines, mostly Android devices from
Samsung, Motorola and LG, as well as a wireless router and some
reference designs
- Six NXP i.MX based machines, mostly industrial boards along with
some reference designs
- Mediatek sees some interesting Filogic based routers including the
"OpenWRT One", a few new Chromebooks as well as single-board
computers.
- Four machines from Solidrun based on Marvell cn913x, replacing the
older Armada 8000 based counterparts
- The four Amlogic machines are all set top boxes or reference
designs for them
- The nine new Rockchips machines are mostly single-board computers
including some interesting ones based on the rk3588 chip like the
ROCK 5 ITX board and the CM3588 with its four NVMe slots
- The RISC-V boards are all single-board computers based on Starfive
JH7110, Microchip MPFS and Allwinner D1, which all had similar
boards already
There are also a lot of updates to already supported machines, notably
for the TI K3, Rockchips, Freescale and of course Qualcomm platforms"
* tag 'soc-dt-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (846 commits)
arm64: dts: allwinner: h616: add crypto engine node
riscv: dts: add clock generator for Sophgo SG2042 SoC
arm64: dts: rockchip: Add Xunlong Orange Pi 3B
dt-bindings: arm: rockchip: Add Xunlong Orange Pi 3B
arm64: dts: rockchip: Add Radxa ROCK 3B
dt-bindings: arm: rockchip: Add Radxa ROCK 3B
mailmap: Update Luca Weiss's email address
ARM: dts: ixp4xx: nslu2: beeper uses PWM
arm64: dts: rockchip: add ROCK 5 ITX board
dt-bindings: arm: rockchip: Add ROCK 5 ITX board
arm64: dts: rockchip: Add dma-names to uart1 on Pine64 rk3566 devices
arm64: dts: rockchip: Add avdd supplies to hdmi on rock64
arm64: dts: qcom: msm8916-lg-c50: add initial dts for LG Leon LTE
arm64: dts: qcom: msm8916-lg-m216: Add initial device tree
dt-bindings: arm: qcom: Add msm8916 based LG devices
ARM: dts: qcom: msm8960: correct memory base
arm64: dts: qcom: ipq9574: Add icc provider ability to gcc
dt-bindings: interconnect: Add Qualcomm IPQ9574 support
arm64: dts: qcom: sm8150: Add video clock controller node
arm64: dts: qcom: pm6150: Add vibrator
...
Add PCIe dts configuraion for JH7110 SoC platform. The Star64 only has
one exposed PCIe port, so only the Mars and VisionFive 2 get two
enabled.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
[conor: squash in star64's single exposed port]
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Currently, for JH7110 boards with EMMC slot, vqmmc voltage for EMMC is
fixed to 1.8V, while the spec needs it to be 3.3V on low speed mode and
should support switching to 1.8V when using higher speed mode. Since
there are no other peripherals using the same voltage source of EMMC's
vqmmc(ALDO4) on every board currently supported by mainline kernel,
regulator-max-microvolt of ALDO4 should be set to 3.3V.
Cc: stable@vger.kernel.org
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Fixes: 7dafcfa79c ("riscv: dts: starfive: enable DCDC1&ALDO4 node in axp15060")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Up to now, the describe flash partition layout has some gaps.
Use the whole flash chip by getting rid of the gaps.
Suggested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The Pine64 Star64 is a development board based on the Starfive JH7110 SoC.
The board features:
- JH7110 SoC
- 4/8 GiB LPDDR4 DRAM
- AXP15060 PMIC
- 40 pin GPIO header
- 1x USB 3.0 host port
- 3x USB 2.0 host port
- 1x eMMC slot
- 1x MicroSD slot
- 1x QSPI Flash
- 2x 1Gbps Ethernet port
- 1x HDMI port
- 1x 4-lane DSI
- 1x 2-lane CSI
- 1x PCIe 2.0 x1 lane
Signed-off-by: Henry Bell <dmoo_dv@protonmail.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
This is to prepare for Milkv Mars board dts support in the following
patch. Let's factored out common part into .dtsi.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
No physical write-protect line is present, so setting "disable-wp".
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Per VisionFive 2 1.2B, and 1.3A boards' SCH, GPIO 41 is used as
card detect. So add "cd-gpios" property for this.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
As pointed out by Krzysztof "Board should not bring new CPU nodes.
Override by label instead."
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Use "audio-codec" as the codec dt node name, and "sound" as the simple
audio card dt name.
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add the 'cpus' label so that we can reference it in board dts files.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
This partially reverts
commit 92cfc35838 ("riscv: dts: starfive: Add the nodes and pins of I2Srx/I2Stx0/I2Stx1")
This added device tree nodes for I2S hardware that is not actually on the
VisionFive 2 board, but connected on the 40pin header. Many different extension
boards could be added on those pins, so this should be handled by overlays
instead.
This also conflicts with the TDM node which also attempts to grab GPIO 44:
starfive-jh7110-sys-pinctrl 13040000.pinctrl: pin GPIO44 already requested by 10090000.tdm; cannot claim for 120c0000.i2s
Fixes: 92cfc35838 ("riscv: dts: starfive: Add the nodes and pins of I2Srx/I2Stx0/I2Stx1")
Signed-off-by: Hannah Peuckmann <hannah.peuckmann@canonical.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
This partially reverts
commit e7c304c034 ("riscv: dts: starfive: jh7110: add the node and pins configuration for tdm")
This added device tree nodes for TDM hardware that is not actually on the
VisionFive 2 board, but connected on the 40pin header. Many different extension
boards could be added on those pins, so this should be handled by overlays
instead.
This also conflicts with the I2S node which also attempts to grab GPIO 44:
starfive-jh7110-sys-pinctrl 13040000.pinctrl: pin GPIO44 already requested by 10090000.tdm; cannot claim for 120c0000.i2s
Fixes: e7c304c034 ("riscv: dts: starfive: jh7110: add the node and pins configuration for tdm")
Signed-off-by: Hannah Peuckmann <hannah.peuckmann@canonical.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Interrupt line number of the AXP15060 PMIC is not a necessary part of
its device tree. Originally the binding required one, so the dts patch
added an invalid interrupt that the driver ignored (0) as the interrupt
line of the PMIC is not actually connected on this platform. This went
unnoticed during review as it would have been a valid interrupt for a
GPIO controller, but it is not for the PLIC. The PLIC, on this platform
at least, silently ignores the enablement of interrupt 0. Bo Gan is
running a modified version of OpenSBI that faults if writes are done to
reserved fields, so their kernel runs into problems.
Delete the invalid interrupt from the device tree.
Cc: stable@vger.kernel.org
Reported-by: Bo Gan <ganboing@gmail.com>
Link: https://lore.kernel.org/all/c8b6e960-2459-130f-e4e4-7c9c2ebaa6d3@gmail.com/
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Fixes: 2378341504 ("riscv: dts: starfive: Enable axp15060 pmic for cpufreq")
[conor: rewrite the commit message to add more detail]
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
These are changes that for some reason ended up not making it into the
first four branches but that should still make it into 6.9:
- A rework of the omap clock support that touches both drivers and
device tree files
- The reset controller branch changes that had a dependency on late
bugfixes. Merging them here avoids a backmerge of 6.8-rc5 into the
drivers branch
- The RISC-V/starfive, RISC-V/microchip and ARM/Broadcom devicetree
changes that got delayed and needed some extra time in linux-next
for wider testing.
-----BEGIN PGP SIGNATURE-----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=IzoE
-----END PGP SIGNATURE-----
Merge tag 'soc-late-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull more ARM SoC updates from Arnd Bergmann:
"These are changes that for some reason ended up not making it into the
first four branches but that should still make it into 6.9:
- A rework of the omap clock support that touches both drivers and
device tree files
- The reset controller branch changes that had a dependency on late
bugfixes. Merging them here avoids a backmerge of 6.8-rc5 into the
drivers branch
- The RISC-V/starfive, RISC-V/microchip and ARM/Broadcom devicetree
changes that got delayed and needed some extra time in linux-next
for wider testing"
* tag 'soc-late-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (31 commits)
soc: fsl: dpio: fix kcalloc() argument order
bus: ts-nbus: Improve error reporting
bus: ts-nbus: Convert to atomic pwm API
riscv: dts: starfive: jh7110: Add camera subsystem nodes
ARM: bcm: stop selecing CONFIG_TICK_ONESHOT
ARM: dts: omap3: Update clksel clocks to use reg instead of ti,bit-shift
ARM: dts: am3: Update clksel clocks to use reg instead of ti,bit-shift
clk: ti: Improve clksel clock bit parsing for reg property
clk: ti: Handle possible address in the node name
dt-bindings: pwm: opencores: Add compatible for StarFive JH8100
dt-bindings: riscv: cpus: reg matches hart ID
reset: Instantiate reset GPIO controller for shared reset-gpios
reset: gpio: Add GPIO-based reset controller
cpufreq: do not open-code of_phandle_args_equal()
of: Add of_phandle_args_equal() helper
reset: simple: add support for Sophgo SG2042
dt-bindings: reset: sophgo: support SG2042
riscv: dts: microchip: add specific compatible for mpfs pdma
riscv: dts: microchip: add missing CAN bus clocks
ARM: brcmstb: Add debug UART entry for 74165
...
Microchip:
Missing bus clocks for the CAN controllers spotted during the creation
of a driver for the controllers and a specific compatible for the SiFive
PDMA block on PolarFire SoC.
Starfive:
PWM nodes for the jh7100 and jh7110. Camera subsystem support for the
latter. Most notably however is the addition of ethernet support for the
jh7110 which finally allows people to use the network on the OG VisionFive
and on the Beagle-V Starlight board. This was made possible by the
non-standard cache management operations support added for the RZ/Five
which could be extended to the ccache present on the jh7100.
bindings:
Additional clarification for what the reg property represents for cpus
and two opencores PWM binding changes - the original addition and an
added compatible. The latter is here as the driver patch was not ready
but the PWM maintainer told me to go ahead and merge it.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCZed3VgAKCRB4tDGHoIJi
0rfBAP9n6/i9bitGfqZHXKc1CpqwIWb8sw28OC4u6UWaNEzSmQEA0R0bagMcfVDi
szpu4+58Bk4hbd/6lOwacdskEUp0bwU=
=gBjh
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmXoD90ACgkQYKtH/8kJ
Uicd9hAAny3U0DB36GMakjIJJkBMSrrbIydydt9mSdkOjsgAt6qUUpBahbMjGE3+
U688dtHOMlsZ0ZubVngN+xYtI6xOXP9SU0+P3u/reCQ8SSZnbtndtwmRFd8ZHJFT
Nx5MSl71SzzSL7E3vT638VlZvcq0a5fcUKPZql40iLUnY0iJ6IdcU8cZLWoqkOZF
R2zhCUGzLuRrAZF9nPgAKGHwPskq1gqWMMCnLf6NIgaxfjf8POuGAgJBVJ1CYg0P
kSzXUrEphjD+IpCbffkGJ1epq1+SbYfYo6P9MisiWbv8/xvoZ+VJnbTb+NLg3Wuo
i8B5uFOBi65rLCCErDDYNr2huESHHC8IN9ndvRG/eXTaLek4WhJ1cxXDPHBzN9OF
DMKKgSeRZnMj/EQ0jQQPK0I9KymVdy+qwAhAr0DKEzGSiiu1hVlxfvspq+EzW9DR
O9v2+hRCALpripRGf7wVG+16HtzvbbH1hHGABb4YTl3rf0bSqXTt84wIQ9MBSe+e
nFsCnOdA5zNBN3gtiKlbYQE/jiTYCeyqfCJOwXlw83KKSGJfNG+mTOR/vhpVOAbq
Djb6dEemeYxZ95P5PFSqm7GOttZWI3vthyWpPeF1qfGuZ6g55+zZyZHsVKevkWzd
54Z/rpLdUBeDRkwNLa9W0r/5oZOLNccKhkS9Qy6umjSsBXa14qA=
=0UyT
-----END PGP SIGNATURE-----
Merge tag 'riscv-dt-for-v6.9' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/late
RISC-V Devicetrees for v6.9
Microchip:
Missing bus clocks for the CAN controllers spotted during the creation
of a driver for the controllers and a specific compatible for the SiFive
PDMA block on PolarFire SoC.
Starfive:
PWM nodes for the jh7100 and jh7110. Camera subsystem support for the
latter. Most notably however is the addition of ethernet support for the
jh7110 which finally allows people to use the network on the OG VisionFive
and on the Beagle-V Starlight board. This was made possible by the
non-standard cache management operations support added for the RZ/Five
which could be extended to the ccache present on the jh7100.
bindings:
Additional clarification for what the reg property represents for cpus
and two opencores PWM binding changes - the original addition and an
added compatible. The latter is here as the driver patch was not ready
but the PWM maintainer told me to go ahead and merge it.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.9' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: starfive: jh7110: Add camera subsystem nodes
dt-bindings: pwm: opencores: Add compatible for StarFive JH8100
dt-bindings: riscv: cpus: reg matches hart ID
riscv: dts: microchip: add specific compatible for mpfs pdma
riscv: dts: microchip: add missing CAN bus clocks
riscv: dts: starfive: beaglev-starlight: Setup phy reset gpio
riscv: dts: starfive: visionfive-v1: Setup ethernet phy
riscv: dts: starfive: jh7100-common: Setup pinmux and enable gmac
riscv: dts: starfive: jh7100: Add sysmain and gmac DT nodes
riscv: dts: starfive: jh7110: Add PWM node and pins configuration
riscv: dts: starfive: jh7100: Add PWM node and pins configuration
dt-bindings: pwm: Add bindings for OpenCores PWM Controller
Link: https://lore.kernel.org/r/20240305-iodine-moneywise-53797ae9bf6e@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add camera subsystem nodes for the StarFive JH7110 SoC. They contain the
dphy-rx, csi2rx, camss nodes.
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Underscores should not be used in node names (dtc with W=2 warns about
them), so replace them with hyphens.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The BeagleV Starlight SBC uses a Microchip KSZ9031RNXCA PHY supporting
RGMII-ID which doesn't require any particular setup, other than defining
a reset gpio, as opposed to VisionFive V1 for which the RX internal
delay had to be adjusted.
Co-developed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The StarFive VisionFive V1 SBC uses a Motorcomm YT8521 PHY supporting
RGMII-ID, but requires manual adjustment of the RX internal delay to
work properly.
The default RX delay provided by the driver is 1.95 ns, which proves to
be too high. Applying a 50% reduction seems to mitigate the issue.
Also note this adjustment is not necessary on BeagleV Starlight SBC,
which uses a Microchip PHY. Hence, there is no indication of a
misbehaviour on the GMAC side, but most likely the issue stems from
the Motorcomm PHY.
While at it, drop the redundant gpio include, which is already provided
by jh7100-common.dtsi.
Co-developed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
