It is considered good practice to disable on-SoC devices providing
external I/O in the SoC-specific .dtsi, and enable them explicitly in
the board-specific DTS files when actually wired-up and used.
Hence:
- Set the status of I/O devices in k210.dtsi to "disabled",
- Override the status of used I/O devices in board-specific DTS files
to "okay",
- Drop unneeded status overrides in board DTS-specific files for the
always-enabled pin controller.
On e.g. MAiXBiT, this gets rid of an error message when probing the
unused slave-only spi2 controller:
dw_spi_mmio 50240000.spi: error -22: problem registering spi host
dw_spi_mmio 50240000.spi: probe with driver dw_spi_mmio failed with error -22
which is seen since commit 98d75b9ef2 ("spi: dw: Drop default
number of CS setting").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The SoC-specific k210.dtsi declares aliases for all four serial ports.
However, none of the board-specific DTS files configure pin control for
any but the first serial port, so the last three ports are not usable.
Move the aliases node from the SoC-specific k210.dtsi to the
board-specific DTS files, as these are really board-specific, and retain
the sole port that is usable.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
This series should rid us of dtbs_check errors for the RISC-V Canaan
k210 based boards. To make keeping it that way a little easier, I
changed the Canaan devicetree Makefile so that it would build all of the
devicetrees in the directory if SOC_CANAAN.
Link: https://lore.kernel.org/all/mhng-85044754-c361-40bc-a6a2-7082f35930bb@palmer-ri-x1c9/
* remotes/palmer/riscv-canaan_dt_schema:
riscv: dts: canaan: build all devicetress if SOC_CANAAN
riscv: dts: canaan: add specific compatible for kd233's LCD
riscv: dts: canaan: fix bus {ranges,reg} warnings
riscv: dts: canaan: remove spi-max-frequency from controllers
riscv: dts: canaan: use custom compatible for k210 i2s
riscv: dts: canaan: fix kd233 display spi frequency
riscv: dts: canaan: fix mmc node names
riscv: dts: canaan: fix the k210's timer nodes
riscv: dts: canaan: fix the k210's memory node
dt-bindings: memory-controllers: add canaan k210 sram controller
dt-bindings: display: ili9341: document canaan kd233's lcd
dt-bindings: display: convert ilitek,ili9341.txt to dt-schema
The binding for the ili9341 specifies a const spi-max-frequency of 10
MHz but the kd233 devicetree entry has it listed at 15 Mhz.
Align the devicetree with the value in the binding.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220705215213.1802496-9-mail@conchuod.ie
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The newly-converted-to-dt-schema binding expects the mmc node name to be
'^mmc(@.*)?$' so align the devicetree with the schema.
Tested-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220705215213.1802496-8-mail@conchuod.ie
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Add the device tree canaan_kd233.dts for the Canaan Kendryte KD233
development board. This device tree enables LEDs, some gpios and
spi/mmc SD card device. The WS2812B RGB LED and the 10 positions rotary
dip switch present on the board are left undefined.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
[Palmer: Remove undocumented microphone entry, along with the use.]
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
