MT7620A devices all contain a wifi device as part of the SOC. Add it
here to get it working.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://patch.msgid.link/20250722212856.11343-7-rosenp@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When starting up, the GARDENA smart Gateway's power LED should be
flashing green. It is unclear why it was initially set to "off".
The LED frequency cannot be configured in the devicetree. Luckily, the
default is 1 Hz, which is what we want.
Signed-off-by: Ezra Buehler <ezra.buehler@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Most notably, add the mediatek,sysctl phandle and remove the redundant
reset/interrupt-related properties from the watchdog node. This is in
line with the corresponding devicetree (mt7628an.dtsi) used by the
OpenWrt project.
This has been tested on the MT7688-based GARDENA smart Gateway.
Signed-off-by: Ezra Buehler <ezra.buehler@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Otherwise, the MT7688-based GARDENA smart Gateway will fail to boot
printing "Kernel panic - not syncing: unable to get CPU clock, err=-2".
Signed-off-by: Ezra Buehler <ezra.buehler@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Current MT7628A device tree file system controller node is wrong since it is
not matching bindings. Hence, update it to match current bindings updating
it also to use new introduced clock constants.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Current MT7620A device tree file system controller node is wrong since it is
not matching bindings. Hence, update it to match current bindings updating
it also to use new introduced clock constants.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Current RT3883 device tree file system controller node is wrong since it is
not matching bindings. Hence, update it to match current bindings updating
it also to use new introduced clock constants.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Current RT3050 device tree file system controller node is wrong since it is
not matching bindings. Hence, update it to match current bindings updating
it also to use new introduced clock constants.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Current RT2880 device tree file system controller node is wrong since it is
not matching bindings. Hence, update it to match current bindings updating
it also to use new introduced clock constants.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Commit 654102df2a ("kbuild: add generic support for built-in boot
DTBs") introduced generic support for built-in DTBs.
Select GENERIC_BUILTIN_DTB and BUILTIN_DTB_ALL when the built-in DTB
support is enabled.
DTBs compiled under arch/mips/boot/dts/ will be wrapped by the generic
rule in scripts/Makefile.vmlinux.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Move the compatible attribute of the DTS root node to first place.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reorder the attributes of the PCIe PHY nodes node to match
what the DTS style guide recommends.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reorder the attributes and child nodes of the PCIe Controller
node to meet the DTS style guidelines.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Rearrange attributes and descendents declared under the
ethernet node, recursively, to follow the DTS style guide.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reorder the attributes of the Global Interrupt Controller
node to fit DTS style guidelines.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Shuffle the attributes of the MMC node to meet the guidelines
provided by the DTS style guide.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Move the pinctrl node prior to the nodes that feature unit
addresses.
Sort pinctrl's child nodes into alphabetical order.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reorder the attributes of the SPI controller node so that
they're aligned with the DTS style guide.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Rearrange the order of the i2c node's attributes so that they
are inline with the DTS style guide.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Shuffle the attributes of the gpio node to appease the DTS
style guide.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reorder the attributes of the sysc node so that the
ralink prefixed attribute is placed after those which lack
prefixes.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reorder the attributes of MMC fixed voltage regulator nodes
for the sake of compliance with the DTS style guide.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reorder the CPU Interrupt Controller node's attributes to follow
what the DTS Coding Style dictates.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reorder cpu node attributes to fit the DTS Coding Style.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add default #address-cells and #size-cells properties to the
usb node, which should be suitable for hubs and devices without
explicitly declared interface nodes, as:
"#address-cells":
description: should be 1 for hub nodes with device nodes,
should be 2 for device nodes with interface nodes.
enum: [1, 2]
"#size-cells":
const: 0
-- from Documentation/devicetree/bindings/usb/usb-device.yaml
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add serial1 and serial2 nodes to define the existence of
the MT7621's second and third UARTs.
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reorder serial0 properties according to the guidelines laid
out in Documentation/devicetree/bindings/dts-coding-style.rst
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add missing pinctrl-name and pinctrl-0 properties to declare
that the uart1_pins group is associated with serial0.
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Rename GB-PC1 to GnuBee GB-PC1, and GB-PC2 to GnuBee GB-PC2 to include
brand and model name.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Each item of the resets property should define a reset. Split the item with
two resets on the ethernet node into two separate items.
Sort the items of the clocks property to the same line as a trivial change.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
We want to unify the pinctrl-single pin group nodes to use naming "pins".
Otherwise non-standad pin group names will add make dtbs checks errors
when the pinctrl-single yaml binding gets merged.
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This WiFi AP is based on a MT7621 SoC with 128MiB RAM, 128MiB NAND,
a MT7603 2.4GHz WiFi and a MT7613 5GHz WiFi chips integrated on the board,
connected to the main SoC over PCIe.
The device uses NMBM over NAND, which is not currently supported in the
mainline, so NAND node is skipped in this revision.
Signed-off-by: Liviu Dudau <liviu@dudau.co.uk>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
To allow to access system controller registers from watchdog driver code
add a phandle in the watchdog 'wdt' node. This avoid using arch dependent
operations in driver code.
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Watchdog nodes must use 'watchdog' for node name. When a 'make dtbs_check'
is performed the following warning appears:
wdt@100: $nodename:0: 'wdt@100' does not match '^watchdog(@.*|-[0-9a-f])?$'
Fix this warning up properly renaming the node into 'watchdog'.
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
On MT7621AT, MT7621DAT, and MT7621ST SoCs, port 5 of the MT7530 switch is
connected to the second MAC of the SoC as a CPU port. Add the port and set
up the second MAC on the bindings. Revert PHY muxing on GB-PC1.
There's an external PHY connected to the second MAC of the SoC on GB-PC2,
therefore, disable port@5 for this device.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The node names should be generic and DT schema expects certain pattern:
mt7621-gnubee-gb-pc1.dtb: gpio-leds: 'power', 'system' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This is not used by the DSA dt-binding, so remove it from all devicetrees.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Change the labels of the DSA ports to generic naming for switch ports.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The phy-mode property must be defined on the MAC instead of the PHY. Define
phy-mode under gmac1 which the external phy is connected to.
Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add the missing LEDs for GB-PC2. The ethblack-green, ethblue-green, power
and system LEDs weren't added previously, because they don't exist on the
device schematics. Tests on a GB-PC2 by me and Petr proved otherwise.
The i2c bus cannot be used on GB-PC2 as its pins are wired to LEDs instead,
and GB-PC1 does not use it. Therefore, do not enable it on both devices.
Link: https://github.com/ngiger/GnuBee_Docs/blob/master/GB-PCx/Documents/GB-PC2_V1.1_schematic.pdf
Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address of the external phy on the mdio bus is 5. Update the devicetree
for GB-PC2 accordingly.
Fixes: 5bc148649c ("staging: mt7621-dts: fix GB-PC2 devicetree")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of muxing phy0 of the MT7530 switch, the switch and the phy
will have the same address on the mdio bus, 0. This causes the ethernet
driver to fail since devices on the mdio bus cannot share an address.
Any address can be used for the switch, therefore, change the switch
address to 0x1f.
Suggested-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change phy-mode of gmac1 to rgmii on mt7621.dtsi. Same code path is
followed for delayed rgmii and rgmii phy-mode on mtk_eth_soc.c.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt-parent property is inherited from the ethernet node as it's a
parent node of the switch node. Therefore, remove the unnecessary
interrupt-parent property from the switch node.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the dtc warnings below.
uartlite@c00: $nodename:0: 'uartlite@c00' does not match '^serial(@.*)?$'
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/serial/8250.yaml
uartlite@c00: Unevaluated properties are not allowed ('clock-names' was unexpected)
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/serial/8250.yaml
sdhci@1e130000: $nodename:0: 'sdhci@1e130000' does not match '^mmc(@.*)?$'
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/mmc/mtk-sd.yaml
xhci@1e1c0000: $nodename:0: 'xhci@1e1c0000' does not match '^usb(@.*)?'
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
xhci@1e1c0000: compatible: ['mediatek,mt8173-xhci'] is too short
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
switch0@0: $nodename:0: 'switch0@0' does not match '^(ethernet-)?switch(@.*)?$'
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml
port@1: status:0: 'off' is not one of ['okay', 'disabled', 'reserved']
From schema: /home/arinc9/.local/lib/python3.10/site-packages/dtschema/schemas/dt-core.yaml
port@2: status:0: 'off' is not one of ['okay', 'disabled', 'reserved']
From schema: /home/arinc9/.local/lib/python3.10/site-packages/dtschema/schemas/dt-core.yaml
port@3: status:0: 'off' is not one of ['okay', 'disabled', 'reserved']
From schema: /home/arinc9/.local/lib/python3.10/site-packages/dtschema/schemas/dt-core.yaml
- Change "memc: syscon@5000" to "memc: memory-controller@5000".
- Change "uartlite: uartlite@c00" to "serial0: serial@c00" and remove the
aliases node.
- Remove "clock-names" from the serial0 node. The property doesn't exist on
the 8250.yaml schema.
- Change "sdhci: sdhci@1e130000" to "mmc: mmc@1e130000".
- Change "xhci: xhci@1e1c0000" to "usb: usb@1e1c0000".
- Add "mediatek,mtk-xhci" as the second compatible string on the usb node.
- Change "switch0: switch0@0" to "switch0: switch@0"
- Change "off" to "disabled" for disabled nodes.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
-----BEGIN PGP SIGNATURE-----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=hTzI
-----END PGP SIGNATURE-----
Merge tag 'mips_5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
"Cleanups and fixes"
* tag 'mips_5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (38 commits)
MIPS: RALINK: Define pci_remap_iospace under CONFIG_PCI_DRIVERS_GENERIC
MIPS: Use memblock_add_node() in early_parse_mem() under CONFIG_NUMA
MIPS: Return -EINVAL if mem parameter is empty in early_parse_mem()
MIPS: Kconfig: Fix indentation and add endif comment
MIPS: bmips: Fix compiler warning observed on W=1 build
MIPS: Rewrite `csum_tcpudp_nofold' in plain C
mips: setup: use strscpy to replace strlcpy
MIPS: Octeon: add SNIC10E board
MIPS: Ingenic: Refresh defconfig for CU1000-Neo and CU1830-Neo.
MIPS: Ingenic: Refresh device tree for Ingenic SoCs and boards.
MIPS: Ingenic: Add PWM nodes for X1830.
MIPS: Octeon: fix typo in comment
MIPS: loongson32: Kconfig: Remove extra space
MIPS: Sibyte: remove unnecessary return variable
MIPS: Use NOKPROBE_SYMBOL() instead of __kprobes annotation
selftests/ftrace: Save kprobe_events to test log
MIPS: tools: no need to initialise statics to 0
MIPS: Loongson: Use hwmon_device_register_with_groups() to register hwmon
MIPS: VR41xx: Drop redundant spinlock initialization
MIPS: smp: optimization for flush_tlb_mm when exiting
...
All pin groups function as gpio unless set otherwise. Therefore, remove
this unnecessary binding.
Tested on UniElec U7621-06-16M on OpenWrt.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Mux the MT7530 switch's phy4 to the SoC's gmac1 on the GB-PC1 devicetree.
This achieves 2 Gbps total bandwidth to the CPU using the second RGMII.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
