Loongson Binary Translation (LBT) is used to accelerate binary translation,
which contains 4 scratch registers (scr0 to scr3), x86/ARM eflags (eflags)
and x87 fpu stack pointer (ftop).
This patch support kernel to save/restore these registers, handle the LBT
exception and maintain sigcontext.
Signed-off-by: Qi Hu <huqi@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Use the generic ptrace_resume code for PTRACE_SYSCALL, PTRACE_CONT,
PTRACE_KILL and PTRACE_SINGLESTEP handling. This implies defining
arch_has_single_step() and implementing the user_enable_single_step()
and user_disable_single_step() functions.
LoongArch cannot do hardware single-stepping per se, the hardware
single-stepping it is achieved by configuring the instruction fetch
watchpoints (FWPS) and specifies that the next instruction must trigger
the watch exception by setting the mask bit. In some scenarios
CSR.FWPS.Skip is used to ignore the next hit result, avoid endless
repeated triggering of the same watchpoint without canceling it.
Signed-off-by: Qing Zhang <zhangqing@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Use perf framework to manage hardware instruction and data breakpoints.
LoongArch defines hardware watchpoint functions for instruction fetch
and memory load/store operations. After the software configures hardware
watchpoints, the processor hardware will monitor the access address of
the instruction fetch and load/store operation, and trigger an exception
of the watchpoint when it meets the conditions set by the watchpoint.
The hardware monitoring points for instruction fetching and load/store
operations each have a register for the overall configuration of all
monitoring points, a register for recording the status of all monitoring
points, and four registers required for configuration of each watchpoint
individually.
Signed-off-by: Qing Zhang <zhangqing@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
The current LoongArch kernel stack is padded as if obeying the MIPS o32
calling convention (32 bytes), signifying the port's MIPS lineage but no
longer making sense. Remove the padding for clarity.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Jinyang He <hejinyang@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
1. Use common arch_stack_walk() infrastructure to avoid duplicated code
and avoid taking care of the stack storage and filtering.
2. Add sched_ra (means sched return address) and sched_cfa (means sched
call frame address) to thread_info, and store them in switch_to().
3. Add __get_wchan() implementation.
Now we can print the process stack and wait channel by cat /proc/*/stack
and /proc/*/wchan.
Signed-off-by: Qing Zhang <zhangqing@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
The `vcsr` only exists in the old hardware design, it isn't used in any
shipped hardware from Loongson-3A5000 on. Both scalar FP and LSX/LASX
instructions use the `fcsr` as their control and status registers now.
For example, the RM control bit in fcsr0 is shared by FP, LSX and LASX
instructions.
Particularly, fcsr16 to fcsr31 are reserved for LSX/LASX now, access to
these registers has no visible effect if LSX/LASX is enabled, and will
cause SXD/ASXD exceptions if LSX/LASX is not enabled.
So, mentions of vcsr are obsolete in the first place (it was just used
for debugging), let's remove them.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Qi Hu <huqi@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Add process management support for LoongArch, including: thread info
definition, context switch and process tracing.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
