Add PCIe phy bindings for the ZCU102.
Link: https://lore.kernel.org/r/20240531161337.864994-8-sean.anderson@linux.dev
Tested-by: Thippeswamy Havalige <thippeswamy.havalige@amd.com>
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michal Simek <michal.simek@amd.com>
All si570 mgt chips have factory default 156.25MHz but DT changed it to
148.5MHz. After tracking it is pretty much c&p fault taken from Zynq
zc702/zc706 boards where 148.5MHz was setup as default because it was
requirement for AD7511 chip available on these boards.
ZynqMP board don't contain this chip that's why factory default frequency
can be used.
Link: https://lore.kernel.org/r/65a53776cbc5e4586f58da57a4b99e4d5c6c26a7.1704728353.git.michal.simek@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
All ZynqMP boards are setting up tx-buswidth to 1. Due to this the
framework only issues 1-1-1 write commands to the GQSPI driver. But the
GQSPI controller is capable of handling 1-4-4 write commands, so updated
the tx-buswidth to 4.
Using all 4 lines will increase the tx data transfer rate, as now the
tx data will be transferred on four lines instead on single line.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/1f1b0028106d83aa06e0777e91862a07df100fa1.1684767562.git.michal.simek@amd.com
As per design, all input/rx pins should have fast slew rate and 12mA
drive strength. Rest all pins should be slow slew rate and 4mA drive
strength. Fix usb nodes as per this and remove setting of slow slew rate
for all the usb group pins.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/379071f44ceb27a0e32d74e13221640922d989d1.1684767562.git.michal.simek@amd.com
TI DP83867 is using strapping based on MIO pins. Tristate setup can
influence PHY address. That's why switch description with ethernet-phy-id
compatible string which enable calling reset. PHY itself setups phy address
after power up or reset. Phy reset is done via gpio.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/b49904649a363f40dc9c4d3fa275e42129562082.1684767562.git.michal.simek@amd.com
Remove is-dual not documented property and also update comment about QSPI
sizes to reflect dual configuration as 16MB + 16MB.
Only single configuration is supported now.
Reported-by: Quanyang Wang <quanyang.wang@windriver.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/876c53b92f99623bae45d5c0c5ae79ee3e24f745.1628239345.git.michal.simek@xilinx.com
The function of_i2c_get_board_info will call of_modalias_node to check
if a device_node contains "compatible" string. But for the device si5328
at zcu102/zcu106 boards, there is no proper DT bindings for them. So remove
si5328 device nodes from dts files to eliminate the error info in the boot
message:
i2c i2c-10: of_i2c: modalias failure on /axi/i2c@ff030000/i2c-mux@74/i2c@4/clock-generator@69
i2c i2c-10: Failed to create I2C device for /axi/i2c@ff030000/i2c-mux@74/i2c@4/clock-generator@69
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210308115437.2232847-1-quanyang.wang@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The convention for node names is to use hyphens, not underscores.
dtschema for pca95xx expects GPIO hogs to end with 'hog' prefix.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200916155715.21009-8-krzk@kernel.org
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Label property is adding capability to distiguish chips from each other
when iio framework is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If there are more instances of si570 clock-output-names property
should be used for differentiation of clock output.
The patch is adding this optional properties for all zynqmp boards with
si570 chip.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Ethernet phys based on devicetree specification should be using
ethernet-phy@ node name instead of pure phy@.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds dr_mode property to the usb node for
zynqmp boards.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add TI PHY strap ctrl quirk for all the HW where applicable.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
s/_/-/ for node names.
It fixes warnings like this:
... Warning (node_name_chars_strict): /cpu_opp_table:
Character '_' not recommended in node name ...
Issues reported by make dtbs W=12
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Most of the legacy "gpio-key,wakeup" boolean property is already
replaced with "wakeup-source". However few occurrences of old property
has popped up again, probably from the remnants in downstream trees.
This patch replaces the legacy properties with the unified
"wakeup-source" property introduced by:
"Input: gpio_keys - switch to using generic device properties"
(sha1: 700a38b27e)
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dts reports incorrect usage of these properties in gpio-keys node.
Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary
The patch is removing these useless properties.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is adding revA, revB and rev1.0. There are also other
revisions between which should be backward compatible with previous
versions. Unfortunately all revs are still in use.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
