According to the "GPIO Expander Map / Table" section of the J722S EVM
Schematic within the Evaluation Module Design Files package [0], the
GPIO Pin P05 located on the GPIO Expander 1 (I2C0/0x23) has to be pulled
down to select the Type-C interface. Since commit under Fixes claims to
enable the Type-C interface, update the property within "p05-hog" from
"output-high" to "output-low", thereby switching from the Type-A
interface to the Type-C interface.
[0]: https://www.ti.com/lit/zip/sprr495
Cc: stable@vger.kernel.org
Fixes: 485705df5d ("arm64: dts: ti: k3-j722s: Enable PCIe and USB support on J722S-EVM")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20250623100657.4082031-1-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
J722S EVM has the CSI2RX routed to a MIPI CSI connector and to 22-pin RPi
camera connector through an analog mux with GPIO control, model mux so
that an overlay can control the mux state according to connected cameras.
Signed-off-by: Yemike Abhilash Chandra <y-abhilashchandra@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250509091911.2442934-3-y-abhilashchandra@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add device tree nodes for two regulators on the J722S-EVM. VSYS_3V3 is the
output of LM5141-Q1, and it serves as an input to TPS22990 which produces
VSYS_3V3_EXP [1]. VSYS_3V3_EXP serves as vin-supply to CSI RPI Connectors.
Signed-off-by: Yemike Abhilash Chandra <y-abhilashchandra@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
[1]: https://www.ti.com/lit/zip/sprr495
Link: https://lore.kernel.org/r/20250509091911.2442934-2-y-abhilashchandra@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Since serdes0 and serdes1 are now enabled by default within the SoC
file, it is no longer necessary to enable them in the board file.
Hence, remove the redundant 'status = "okay"' within the serdes0 and
serdes1 device-tree nodes.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250417123246.2733923-5-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
In preparation for disabling "serdes_wiz0" and "serdes_wiz1" device-tree
nodes in the SoC file, enable them in the board file. The motivation for
this change is that of following the existing convention of disabling
nodes in the SoC file and only enabling the required ones in the board
file.
Fixes: 485705df5d ("arm64: dts: ti: k3-j722s: Enable PCIe and USB support on J722S-EVM")
Cc: stable@vger.kernel.org
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250417123246.2733923-2-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
J722S EVM has four RPi camera connectors and dual MIPI Samtec CSI
connectors which bring out the 4 x CSI2RX instances and the I2C camera
control interfaces. Add the nodes for PCA9543 I2C switch and enable them.
J722S EVM schematics: https://www.ti.com/lit/pdf/sprujb5
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Yemike Abhilash Chandra <y-abhilashchandra@ti.com>
Link: https://lore.kernel.org/r/20250218185452.600797-4-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
J722S SOC has two usb controllers USB0 and USB1. USB0 is brought out on
the EVM as a stacked USB connector which has one Type-A and one Type-C
port. These Type-A and Type-C ports are connected to MUX so only
one of them can be enabled at a time.
Commit under Fixes, tries to enable the USB0 instance of USB to
interface with the Type-C port via the USB hub, by configuring the
USB2.0_MUX_SEL to GPIO_ACTIVE_HIGH. But it is observed on J722S-EVM
that Type-A port is enabled instead of Type-C port.
Fix this by setting USB2.0_MUX_SEL to GPIO_ACTIVE_LOW to enable Type-C
port.
Fixes: 485705df5d ("arm64: dts: ti: k3-j722s: Enable PCIe and USB support on J722S-EVM")
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20250116125726.2549489-1-h-salunke@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add support for TPS6522x PMIC family on wakeup I2C0 bus.
This device provides regulators (bucks and LDOs), along with
GPIOs, and monitors SOC's MCU error signal.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250102103814.102499-1-u-kumar1@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Enable support for mcu_i2c0 and add pinmux required to bring out the
mcu_i2c0 signals on 40-pin RPi expansion header on the J722S EVM.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Signed-off-by: Shreyash Sinha <s-sinha@ti.com>
Reviewed-by: Prasanth Babu Mantena <p-mantena@ti.com>
Link: https://lore.kernel.org/r/20241105091224.23453-1-b-kapoor@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The K3 J722S-EVM platform is based on the J722S SoC which has one
single-core Arm Cortex-R5F processor in each of the WAKEUP, MCU and MAIN
voltage domain, and two C71x DSP subsystems in MAIN voltage domain.
The Inter-Processor communication between the A53 cores and these R5F
and DSP remote cores is achieved through shared memory and Mailboxes.
Thus, add the memory carveouts and enable the mailbox clusters required
for communication.
Also, The remoteproc firmware like of R5F and DSPs in the MAIN voltage
domain use timers. Therefore, change the status of the timer nodes to
"reserved" to avoid any clash during booting of remotecores. Usage is
described as below:
+===================+=============+
| Remoteproc Node | Timer Node |
+===================+=============+
| main_r5fss0_core0 | main_timer0 |
+-------------------+-------------+
| c7x_0 | main_timer1 |
+-------------------+-------------+
| c7x_1 | main_timer2 |
+-------------------+-------------+
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Signed-off-by: Beleswar Padhi <b-padhi@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240830161742.925145-3-b-padhi@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
CAN instances 0 and 1 in the mcu domain and 0 in the main domain are
brought on the evm through headers J5, J8 and J10 respectively. Thus,
add their respective transceiver's 0, 1 and 2 dt nodes as well as
add the required pinmux to add support for these CAN instances.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Reviewed-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20240827105644.575862-2-b-kapoor@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
System firmware uses main_uart5 in J722S EVM for trace data.
Thus, describe it in device tree for completeness,
adding the pinmux and mark it as reserved.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240827105644.575862-3-b-kapoor@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The audio support on J722S-EVM is using TLV320AIC3106[0] codec
connected to McASP1 serializers.
- Add the nodes for sound-card, audio codec and McASP1.
- Add hog for TRC_MUX_SEL to select between McASP and TRACE signals
- Add hogs for GPIO_AUD_RSTn and MCASP1_FET_SEL which is used to
switch between HDMI audio and codec audio.
- Add pinmux for MCASP1 and AUDIO_EXT_REFCLK1.
[0]: <https://www.ti.com/lit/gpn/TLV320AIC3106>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240625113301.217369-3-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Enable PCIe0 instance of PCIe in Root Complex mode of operation with Lane 0
of the SERDES1 instance of SERDES. Also enable USB0 instance of USB to
interface with the Type-C port via the USB hub, by configuring the pin P05
of the GPIO expander on the EVM. Enable USB1 instance of USB in SuperSpeed
mode of operation with Lane 0 of the SERDES0 instance of SERDES.
Co-developed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240615081600.3602462-8-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The J722S EVM has an on-board eMMC. Enable the SDHC interface for it.
There is no pinmuxing required because the interface has dedicated pins.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20240403102302.3934932-1-mwalle@kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Device tree best practice is to disable any external interface in the
dtsi and just enable them if needed in the device tree. Thus, disable
the ethernet switch and its ports by default and just enable the ones
used by the EVMs in their device trees.
There is no functional change.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Acked-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403101545.3932437-1-mwalle@kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
J722S EVM has S28HS512T 64 MiB Octal SPI NOR flash connected
to the OSPI interface, add support for the flash and describe
the partition information as per bootloader.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20240219090435.934383-3-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Enable MAC Port 1 of CPSW3G instance of CPSW Ethernet Switch in
RGMII-RXID mode of operation. Port 2 is not connected on the EVM,
thus keep it disabled.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20240219090435.934383-2-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
