For the ICSSG PHYs to operate correctly, a 25 MHz reference clock must
be supplied on CLKOUT0. Previously, our bootloader configured this
clock, which is why the PRU Ethernet ports appeared to work, but the
change never made it into the device tree.
Add clock properties to make EXT_REFCLK1.CLKOUT0 output a 25MHz clock.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Fixes: 87adfd1ab0 ("arm64: dts: ti: am642-phyboard-electra: Add PRU-ICSSG nodes")
Link: https://lore.kernel.org/r/20250521053339.1751844-1-w.egorov@phytec.de
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The bootph-all and bootph-pre-ram tags were introduced in dt-schema
(dtschema/schemas/bootph.yaml) to define node usage across different
boot phases.
Add boot phase tags to all required nodes to ensure boot support from
all sources, including UART, Ethernet, uSD card, eMMC, and OSPI NOR Flash.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20250305085537.3976579-3-w.egorov@phytec.de
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Be default, R511 iand D19 are not populated on our phyBOARD-Electra.
This resistor and diode connect VCC_3V3_SW with VBAT and permanently
charge the RTC battery.
Enable trickle charge to charge the battery through the RTC.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240911124251.702590-3-w.egorov@phytec.de
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The bus-width property was moved to k3-am64-main.dtsi.
See commit 0ae3113a46 ("arm64: dts: ti: k3-am6*: Fix bus-width property
in MMC nodes")
Signed-off-by: John Ma <jma@phytec.com>
Link: https://lore.kernel.org/r/20240926184918.3342719-2-jma@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Remove pinmuxing for PCIe so that we can add it in an overlay.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240613195012.1925920-2-nmorrisson@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The phyBOARD-Electra has two TCAN1044VDD CAN transceivers which
support CAN FD at 8 Mbps.
Increase the maximum bitrate to 8 Mbps.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240402160825.1516036-3-nmorrisson@phytec.com
Signed-off-by: Nishanth Menon <nm@ti.com>
As described in the binding document for the "current-speed" property:
"This should only be present in case a driver has no chance to know the
baud rate of the slave device."
This is not the case for the UART used in K3 devices, the current
baud-rate can be calculated from the registers. Having this property
has the effect of actually skipping the baud-rate setup in some drivers
as it assumes it will already be set to this rate, which may not always
be the case.
It seems this property's purpose was mistaken as selecting the desired
baud-rate, which it does not. It would have been wrong to select that
here anyway as DT is not the place for configuration, especially when
there are already more standard ways to set serial baud-rates.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240326185441.29656-2-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Remove DLL properties which are not applicable for soft PHYs
since these PHYs do not have a DLL to enable.
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com> # Verdin AM62
Signed-off-by: Judith Mendez <jm@ti.com>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240213235701.2438513-7-jm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Modify license to include dual licensing as GPL-2.0-only OR MIT
license for device trees belonging to PHYTEC Messtechnik GmbH and
PHYTEC America, LLC platforms. This allows for Linux kernel device
tree to be used in other Operating System ecosystems such as Zephyr or
FreeBSD.
While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync
with latest SPDX conventions (GPL-2.0 is deprecated).
While at this, update the copyright year to sync with current year
to indicate license change.
Cc: Garrett Giordano <ggiordano@phytec.com>
Cc: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Garrett Giordano <ggiordano@phytec.com>
Acked-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240122145539.194512-15-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The phyBOARD-Electra populates a TPM module on SPI0 bus.
Add support for the Infineon SLB9670 TPM module.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240123102921.1348777-1-w.egorov@phytec.de
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
SDHCI nodes defined in the top-level AM64 SoC dtsi files are incomplete
and will not be functional unless they are extended.
As the attached SD/eMMC is only known about at the board integration level,
these nodes should only be enabled when provided with this information.
Disable the SDHCI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117163339.89952-2-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The DTS uses constants for SERDES MUX idle state values which were earlier
provided as bindings header. But they are unsuitable for bindings.
So move these constants in a header next to DTS.
Also add J784S4 SERDES4 lane definitions which were missed earlier.
Suggested-by: Nishanth Menon <nm@ti.com>
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Suggested-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/linux-arm-kernel/b24c2124-fe3b-246c-9af9-3ecee9fb32d4@kernel.org/
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20230721125732.122421-2-j-choudhary@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Prepare for pinctrl-single yaml binding and unify pin group node names.
Let's standardize on pin group node naming ending in -pins. As we don't
necessarily have a SoC specific compatible property for pinctrl-single.
I'd rather not add a pattern match for pins somewhere in the name for all
the users.
Trying to add matches for pins-default will be futile as on the earlier
SoCs we've already seen names like pins-sleep, pins-idle, pins-off and so
on that would need to be matched.
And as the node is a pin group, let's prefer to use naming -pins rather
than -pin as more pins may need to be added to the pin group later on.
Signed-off-by: Tony Lindgren <tony@atomide.com>
[vigneshr@ti.com: Rebase onto latest ti/next and extend to new nodes]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
As the binding for "current-speed" states, this should only be used
when the baud rate of an attached device cannot be detected. This is
the case for our attached on-board USB-to-UART converter used for
early kernel console. For all other unconnected/disabled ports this
can be configured in userspace later, DT is not the place for device
configuration, especially when there are already standard ways to
set serial baud in userspace.
Remove setting baud for all disabled serial ports and move setting
it for the couple enabled ports down into the board files.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230601184933.358731-1-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
When referring to array of phandles, using <> to separate the array
entries is better notation as it makes potential errors with phandle
and cell arguments easier to catch. Fix the outliers to be consistent
with the rest of the usage.
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230606182220.3661956-7-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
With commit 9f6ffd0da6 ("dt-bindings: leds: Convert PCA9532 to dtschema"),
we can now add the LED controller without introducing new dtbs_check warnings.
Add missing I2C LED controller.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20230505131012.2027309-1-w.egorov@phytec.de
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add basic support for phyCORE-AM64x SoM & phyBOARD-Electra-AM642 CB.
The phyCORE-AM64x [1] is a SoM (System on Module) featuring TI's AM64x SoC.
It can be used in combination with different carrier boards.
This module can come with different sizes and models for
DDR, eMMC, SPI NOR Flash and various SoCs from the AM64x family.
A development Kit, called phyBOARD-Electra [2] is used as a carrier board
reference design around the AM64x SoM.
Supported features:
* Debug UART
* Heartbeat LED
* GPIO buttons & LEDs
* SPI NOR flash
* eMMC
* CAN
* Ethernet
* Micro SD card
* I2C EEPROM
* I2C RTC
* I2C LED Dimmer
* USB
For more details, see:
[1] Product page SoM: https://www.phytec.com/product/phycore-am64x
[2] Product page CB: https://www.phytec.com/product/phyboard-am64x
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20230104162927.1215033-2-w.egorov@phytec.de
