Enable both SERDES and PCIe DT nodes in order to get PCIe working on
the SERDES PCIe x2 personality card.
The daughter card also has a USB 2.0 dual-role port. As the base board
already supports a 2.0 dual-role port, enable the port on the SERDES
card to be a host only port.
This will prevent user confusion as having 2 ports in device mode often
leads to confusion as to which port is bound to the gadget function driver.
The PCIe x2 card is provided with the AM65x IDK configuration [1]
so apply the overlay to k3-am654-idk.dtb
[1] https://www.ti.com/lit/ug/spruim6a/spruim6a.pdf
Co-developed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20240208-for-v6-9-am65-overlays-2-0-v2-2-70bae3e91597@kernel.org
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add the overlay dtbo file to a Makefile target so it can be
picked by the dtbs_install command.
Fixes: b8690ed3d1 ("arm64: dts: ti: am65x: Add Rocktech OLDI panel DT overlay")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20240208-for-v6-9-am65-overlays-2-0-v2-1-70bae3e91597@kernel.org
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
SPDX identifier GPL-2.0 has been deprecated since license list version
3.0. Use GPL-2.0-only to be specific.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240122145539.194512-17-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
HDMI audio can be enabled over AM62A-SK using the same DT overlay that
is used for AM625 / AM62-LP SK-EVMs.
Add the sk.dtb + hdmi-audio.dtbo combination for AM62A7-SK as well, to
check for overlay applicability during DTBS compile tests.
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20240201125452.1920623-4-a-bhatia1@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add overlay to enable the PCIE1 instance of PCIe on J721S2-EVM in
Endpoint mode of operation.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231211115535.1264353-3-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add overlay to enable the PCIE0 instance of PCIe on J721E-EVM in
Endpoint mode of operation.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231211115535.1264353-2-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Combined dtb builds are only useful for making sure that the overlay
applies cleanly on the base dtb.
So we move all such combined blobs under a `dtb- +=` section that is
only built when CONFIG_OF_ALL_DTBS is enabled.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231201-csi_dts-v3-9-9f06f31080fe@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
RPi v2 Camera (IMX219) is an 8MP camera that can be used with SK-AM62A
through the 22-pin CSI-RX connector.
Same overlay can be used across SK-AM62* boards that have a 15/22-pin
FFC connector, so we name it with the k3-am62x- prefix.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231201-csi_dts-v3-8-9f06f31080fe@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Three different OV5640 modules are supported using the 15-pin FFC
connector on SK-AM62:
- Digilent PCam 5C
- ALINX AN5641
- TEVI-OV5640-*-RPI
The Digilent and ALINX modules supply a 12Mhz XCLK to the sensor, while
the TEVI module supplies a 24Mhz XCLK, thus requiring a separate
overlay.
These overlays can be used on other boards of the SK-AM62* family that
have a 15/22-pin FFC connector, so we name the overlays with the prefix
k3-am62x-.
Tested-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231201-csi_dts-v3-6-9f06f31080fe@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Three different OV5640 modules are supported using the FFC connector on
BeaglePlay:
- Digilent PCam 5C
- ALINX AN5641
- TEVI-OV5640-*-RPI
The Digilent and ALINX modules supply a 12Mhz XCLK to the sensor, while
the TEVI module supplies a 24Mhz XCLK, thus requiring a separate
overlay.
Reviewed-by: Andrew Davis <afd@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231201-csi_dts-v3-4-9f06f31080fe@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The IDK application board has 4 Gigabit Ethernet ports.
This patch adds support for the 4 Gigabit Ethernet ports
which are provided by ICSSG0 and ICSSG1.
The IEP0 SYNC_OUT0 pins are used for PPS out on the IDK card.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20231020051937.3709871-4-danishanwar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Specify the base dtb file k3-j721s2-common-proc-board.dtb on which the
k3-j721s2-evm-gesi-exp-board.dtbo overlay has to be applied. Name the
resulting dtb as k3-j721s2-evm.dtb.
Fixes: cac04e27f0 ("arm64: dts: ti: k3-j721s2: Add overlay to enable main CPSW2G with GESI")
Reported-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20230912043308.20629-1-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add basic support for the AM62P5 SK with UART console and
ramdisk as rootfs.
Schematics is at https://www.ti.com/lit/zip/sprr487
Signed-off-by: Bryan Brattlof <bb@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20230811184432.732215-4-vigneshr@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Enable audio output over HDMI instead of the 3.5mm jack.
A FET switch (U65) on the EVM muxes serial audio lines coming from McASP
between the codec (tlv320aic3106) and the HDMI bridge (sii9022).
By default it uses the codec, but it can be toggled to use the HDMI
bridge by shorting a (J24) header on the board.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
[a-bhatia1: Cosmetic changes]
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20230809084559.17322-5-a-bhatia1@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The MAIN CPSW2G instance of CPSW on J721S2 SoC can be enabled with the GESI
Expansion Board connected to the J7 Common-Proc-Board. Use the overlay
to enable this.
Add alias for the MAIN CPSW2G port to enable kernel to fetch MAC address
directly from U-Boot.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Link: https://lore.kernel.org/r/20230726065407.378455-3-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The J7 GESI EXP board for J721E Common-Proc-Board supports RGMII mode.
Use the overlay to configure CPSW9G ports in RGMII-RXID mode.
Add aliases for CPSW9G ports to enable kernel to fetch MAC addresses
directly from U-Boot.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Link: https://lore.kernel.org/r/20230725073057.96705-1-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The phyCORE-AM62x [1] is a SoM (System on Module) featuring TI's AM62x SoC.
It can be used in combination with different carrier boards.
This module can come with different sizes and models for
DDR, eMMC, SPI NOR Flash and various SoCs from the AM62x family.
A development Kit, called phyBOARD-Lyra [2] is used as a carrier board
reference design around the AM62x SoM.
Supported features:
* Debug UART
* SPI NOR Flash
* eMMC
* 2x Ethernet
* Micro SD card
* I2C EEPROM
* I2C RTC
* GPIO Expander
* LEDs
* USB
For more details, see:
[1] Product page SoM: https://www.phytec.com/product/phycore-am62x
[2] Product page CB: https://www.phytec.com/product/phyboard-am62x
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230504140143.1425951-2-w.egorov@phytec.de
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The OLDI-LCD1EVM add on board has Rocktech RK101II01D-CT panel[1] with
integrated touch screen. The integrated touch screen is Goodix GT928.
This panel connects with AM65 GP-EVM[2].
Add DT nodes for these and connect the endpoint nodes with DSS.
[1]: Panel link
https://www.digimax.it/en/tft-lcd/20881-RK101II01D-CT
[2]: AM654 LCD EVM:
https://www.ti.com/tool/TMDSLCD1EVM
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
[abhatia1@ti.com: Make cosmetic and 6.4 kernel DTSO syntax changes]
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230509102354.10116-2-a-bhatia1@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The AM62x LP SK board is similar to the AM62x SK board, but has some
not-so-minor changes that requires different device tree.
The differences are mainly:
- AM62x SoC in the AMC package that meets AECQ100 automotive standard.
- LPDDR4 versus DDR4 on the AM62x SK.
- TPS65219 PMIC instead of discrete regulators.
- IO expander pin names are wired differently.
- Second ethernet port is currently disabled as the boards do not have
the part physically installed.
- OSPI NAND vs OSPI NOR.
- No WLAN chip instead a SDIO M.2 connector.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
[vigneshr@ti.com: Add PMIC node]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20230321-am62-lp-sk-v2-3-0a56e1694804@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
BeagleBoard.org BeaglePlay is an easy to use, affordable open source
hardware single board computer based on the Texas Instruments AM625
SoC that allows you to create connected devices that work even at long
distances using IEEE 802.15.4g LR-WPAN and IEEE 802.3cg 10Base-T1L.
Expansion is provided over open standards based mikroBUS, Grove and
QWIIC headers among other interfaces.
This board family can be identified by the 24c32 eeprom:
[aa 55 33 ee 01 37 00 10 2e 00 42 45 41 47 4c 45 |.U3..7....BEAGLE|]
[50 4c 41 59 2d 41 30 2d 00 00 30 32 30 30 37 38 |PLAY-A0-..020078|]
https://beagleplay.org/https://git.beagleboard.org/beagleplay/beagleplay
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230316152143.2438928-3-nm@ti.com
Co-developed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
The J7 Quad Port Add-On Ethernet Card for J7200 Common-Proc-Board supports
QSGMII mode. Use the overlay to configure CPSW5G ports in QSGMII mode.
Add support to reset the PHY from kernel by using gpio-hog and gpio-reset.
Add aliases for CPSW5G ports to enable kernel to fetch MAC addresses
directly from U-Boot.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230315062307.1612220-5-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The J7 Quad Port Add-On Ethernet Card for J721E Common-Proc-Board supports
QSGMII mode. Use the overlay to configure CPSW9G ports in QSGMII mode.
Add support to reset the PHY from kernel by using gpio-hog and gpio-reset.
Add aliases for CPSW9G ports to enable kernel to fetch MAC addresses
directly from U-Boot.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230315062307.1612220-3-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Entries are first grouped as per SoC present on the board. Groups are
sorted alphabetically. This makes it easy to know SoC to board mapping
and also add new entries in alphabetical order.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20230126071159.2337584-1-vigneshr@ti.com
AM69 Starter Kit is a single board designed for TI AM69 SOC that
provides advanced system integration in automotive ADAS applications,
autonomous mobile robot and edge AI applications. The SOC comprises
of Cortex-A72s in dual clusters, lockstep capable dual Cortex-R5F MCUs,
Vision Processing Accelerators (VPAC) with Image Signal Processor (ISP)
and multiple vision assist accelerators, Depth and Motion Processing
Accelerators (DMPAC), Deep-learning Matrix Multiply Accelerator(MMA)
and C7x floating point vector DSP
AM69 SK supports the following interfaces:
* 32 GB LPDDR4 RAM
* x1 Gigabit Ethernet interface
* x3 USB 3.0 Type-A ports
* x1 USB 3.0 Type-C port
* x1 UHS-1 capable micro-SD card slot
* x4 MCAN instances
* 32 GB eMMC Flash
* 512 Mbit OSPI flash
* x2 Display connectors
* x1 PCIe M.2 M Key
* x1 PCIe M.2 E Key
* x1 4L PCIe Card Slot
* x3 CSI2 Camera interface
* 40-pin Raspberry Pi header
Add initial support for the AM69 SK board.
Design Files: https://www.ti.com/lit/zip/SPRR466
TRM: https://www.ti.com/lit/zip/spruj52
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20230119132958.124435-3-sabiya.d@ti.com
The M.2 variant comes with 2 slots, one B-keyed and another one E-keyed.
They are configured by the firmware during startup. Also the device tree
will be adjusted according to the detect or manually configured
interface mode by the firmware. The kernel only carries a single
configuration as base device tree. It has to be built with a symbols
node so that the firmware can apply overlays for the connector modes.
Signed-off-by: chao zeng <chao.zeng@siemens.com>
[Jan: refactored to a single DT]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/878e3a023767b5a6d9d2cff09015678aaba13fce.1674110442.git.jan.kiszka@siemens.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The SK architecture comprises of baseboard and a SOM board. The
AM68 Starter Kit's baseboard contains most of the actual connectors,
power supply etc. The System on Module (SoM) is plugged on to the base
board. Therefore, add support for peripherals brought out in the base
board.
Schematics: https://www.ti.com/lit/zip/SPRR463
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Tested-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20230116071446.28867-4-sinthu.raja@ti.com
Add basic support for phyCORE-AM64x SoM & phyBOARD-Electra-AM642 CB.
The phyCORE-AM64x [1] is a SoM (System on Module) featuring TI's AM64x SoC.
It can be used in combination with different carrier boards.
This module can come with different sizes and models for
DDR, eMMC, SPI NOR Flash and various SoCs from the AM64x family.
A development Kit, called phyBOARD-Electra [2] is used as a carrier board
reference design around the AM64x SoM.
Supported features:
* Debug UART
* Heartbeat LED
* GPIO buttons & LEDs
* SPI NOR flash
* eMMC
* CAN
* Ethernet
* Micro SD card
* I2C EEPROM
* I2C RTC
* I2C LED Dimmer
* USB
For more details, see:
[1] Product page SoM: https://www.phytec.com/product/phycore-am64x
[2] Product page CB: https://www.phytec.com/product/phyboard-am64x
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20230104162927.1215033-2-w.egorov@phytec.de
BeagleBoard.org BeagleBone AI-64 is an open source hardware single
board computer based on the Texas Instruments TDA4VM SoC featuring
dual-core 2.0GHz Arm Cortex-A72 processor, C7x+MMA and 2 C66x
floating-point VLIW DSPs, 3x dual Arm Cortex-R5 co-processors,
2x 6-core Programmable Real-Time Unit and Industrial Communication
SubSystem, PowerVR Rogue 8XE GE8430 3D GPU. The board features 4GB
DDR4, USB3.0 Type-C, 2x USB SS Type-A, miniDisplayPort, 2x 4-lane
CSI, DSI, 16GB eMMC flash, 1G Ethernet, M.2 E-key for WiFi/BT, and
BeagleBone expansion headers.
This board family can be indentified by the BBONEAI-64-B0 in the
at24 eeprom:
[aa 55 33 ee 01 37 00 10 2e 00 42 42 4f 4e 45 41 |.U3..7....BBONEA|]
[49 2d 36 34 2d 42 30 2d 00 00 42 30 30 30 37 38 |I-64-B0-..B00078|]
https://beagleboard.org/ai-64https://git.beagleboard.org/beagleboard/beaglebone-ai-64
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Reviewed-by: Andrew Davis <afd@ti.com>
CC: Nishanth Menon <nm@ti.com>
CC: Vignesh Raghavendra <vigneshr@ti.com>
CC: Tero Kristo <kristo@kernel.org>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20221118163139.3592054-2-robertcnelson@gmail.com
AM62A StarterKit (SK) board is a low cost, small form factor board
designed for TI’s AM62A7 SoC. It supports the following interfaces:
* 2 GB LPDDR4 RAM
* x1 Gigabit Ethernet interface
* x1 HDMI Port with audio
* x1 Headphone Jack
* x1 USB2.0 Hub with two Type A host and x1 USB Type-C DRP Port
* x1 UHS-1 capable µSD card slot
* M.2 SDIO Wifi + UART slot
* 1Gb OSPI NAND flash
* x4 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin User Expansion Connector
* 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO)
* 20-pin header for Programmable Realtime Unit (PRU) IO pins
* 40-pin CSI header
Add basic support for AM62A7-SK.
Schematics: https://www.ti.com/lit/zip/sprr459
Co-developed-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Devarsh Thakkar <devarsht@ti.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220901141328.899100-6-vigneshr@ti.com
AM62 StarterKit (SK) board is a low cost, small form factor board
designed for TI’s AM625 SoC. It supports the following interfaces:
* 2 GB DDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode
* x1 HDMI Port with audio + x1 OLDI/LVDS Display interface for Dual Display
* x1 Headphone Jack
* x1 USB2.0 Hub with two Type A host and x1 USB Type-C DRP Port
* x1 UHS-1 capable µSD card slot
* 2.4/5 GHz WLAN + Bluetooth 4.2 through WL1837
* 512 Mbit OSPI flash
* x4 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin User Expansion Connector
* 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO)
* 20-pin header for Programmable Realtime Unit (PRU) IO pins
* 15-pin CSI header
Add basic support for AM62-SK.
Schematics: https://www.ti.com/lit/zip/sprr448
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20220225120239.1303821-6-vigneshr@ti.com
The EVM architecture for J721S2 is similar to that of J721E and J7200. It
is as follows,
+------------------------------------------------------+
| +-------------------------------------------+ |
| | | |
| | Add-on Card 1 Options | |
| | | |
| +-------------------------------------------+ |
| |
| |
| +-------------------+ |
| | | |
| | SOM | |
| +--------------+ | | |
| | | | | |
| | Add-on | +-------------------+ |
| | Card 2 | | Power Supply
| | Options | | |
| | | | |
| +--------------+ | <---
+------------------------------------------------------+
Common Processor Board
Common Processor board is the baseboard that contains most of the actual
connectors, power supply etc. The System on Module (SoM) is plugged on to
the common processor baord. Therefore, add support for peripherals brought
out in the common processor board.
Common Processor Board: https://www.ti.com/tool/J721EXCPXEVM
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20211207080904.14324-6-a-govindraju@ti.com
J721E Starter Kit (SK)[1] is a low cost, small form factor board designed
for TI’s J721E SoC. TI’s J721E SoC comprises of dual core A72, high
performance vision accelerators, video codec accelerators, latest C71x
and C66x DSP, high bandwidth real-time IPs for capture and display, GPU,
dedicated safety island and security accelerators. The SoC is power
optimized to provide best in class performance for industrial and
automotive applications.
J721E SK supports the following interfaces:
* 4 GB LPDDR4 RAM
* x1 Gigabit Ethernet interface
* x1 USB 3.0 Type-C port
* x3 USB 3.0 Type-A ports
* x1 PCIe M.2 E Key
* x1 PCIe M.2 M Key
* 512 Mbit OSPI flash
* x2 CSI2 Camera interface (RPi and TI Camera connector)
* 40-pin Raspberry Pi GPIO header
Add basic support for J721E-SK.
[1] https://www.ti.com/tool/SK-TDA4VM
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210929081333.26454-3-sinthu.raja@ti.com
This adds the devices trees for IOT2050 Product Generation 2 (PG2)
boards. We have Basic and an Advanced variants again, differing in
number of cores, RAM size, availability of eMMC and further details.
The major difference to PG1 is the used silicon revision (SR2.x on
PG2).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/cc868da8264324bde2c87d0c01d4763e3678c706.1632657917.git.jan.kiszka@web.de
Make sure that the platforms are grouped together per SoC. This helps
keep the Makefile readable as newer platforms get added to the list.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210915121442.27112-1-nm@ti.com
AM642 StarterKit (SK) board is a low cost, small form factor board
designed for TI’s AM642 SoC. It supports the following interfaces:
* 2 GB LPDDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in switch and MAC mode
* x1 USB 3.0 Type-A port
* x1 UHS-1 capable µSD card slot
* 2.4/5 GHz WLAN + Bluetooth 4.2 through WL1837
* 512 Mbit OSPI flash
* x2 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin Raspberry Pi compatible GPIO header
* 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO)
* 54-pin header for Programmable Realtime Unit (PRU) IO pins
* Interface for remote automation. Includes:
* power measurement and reset control
* boot mode change
Add basic support for AM642 SK.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210226184251.26451-3-lokeshvutla@ti.com
The AM642 EValuation Module (EVM) is a board that provides access to
various peripherals available on the AM642 SoC, such as PCIe, USB 2.0,
CPSW Ethernet, ADC, and more.
Introduce support for the AM642 EVM to enable mmc boot, including
enabling UART and I2C on the board.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20210226144257.5470-6-d-gerlach@ti.com
Add support for J7200 Common Processor Board.
The EVM architecture is very similar to J721E as follows:
+------------------------------------------------------+
| +-------------------------------------------+ |
| | | |
| | Add-on Card 1 Options | |
| | | |
| +-------------------------------------------+ |
| |
| |
| +-------------------+ |
| | | |
| | SOM | |
| +--------------+ | | |
| | | | | |
| | Add-on | +-------------------+ |
| | Card 2 | | Power Supply
| | Options | | |
| | | | |
| +--------------+ | <---
+------------------------------------------------------+
Common Processor Board
Common Processor board is the baseboard that has most of the actual
connectors, power supply etc. A SOM (System on Module) is plugged on
to the common processor board and this contains the SoC, PMIC, DDR and
basic high speed components necessary for functionality.
Note:
* The minimum configuration required to boot up the board is System On
Module(SOM) + Common Processor Board.
* Since there is just a single SOM and Common Processor Board, we are
maintaining common processor board as the base dts and SOM as the dtsi
that we include. In the future as more SOM's appear, we should move
common processor board as a dtsi and include configurations as dts.
* All daughter cards beyond the basic boards shall be maintained as
overlays.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200914162231.2535-6-lokeshvutla@ti.com
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add Support for J721E Common Processor board support.
The EVM architecture is as follows:
+------------------------------------------------------+
| +-------------------------------------------+ |
| | | |
| | Add-on Card 1 Options | |
| | | |
| +-------------------------------------------+ |
| |
| |
| +-------------------+ |
| | | |
| | SOM | |
| +--------------+ | | |
| | | | | |
| | Add-on | +-------------------+ |
| | Card 2 | | Power Supply
| | Options | | |
| | | | |
| +--------------+ | <---
+------------------------------------------------------+
Common Processor Board
Common Processor board is the baseboard that has most of the actual
connectors, power supply etc. A SOM (System on Module) is plugged on
to the common processor board and this contains the SoC, PMIC, DDR and
basic high speed components necessary for functionality. Add-n card
options add further functionality (such as additional Audio, Display,
networking options).
Note:
A) The minimum configuration required to boot up the board is System On
Module(SOM) + Common Processor Board.
B) Since there is just a single SOM and Common Processor Board, we are
maintaining common processor board as the base dts and SOM as the dtsi
that we include. In the future as more SOM's appear, we should move
common processor board as a dtsi and include configurations as dts.
C) All daughter cards beyond the basic boards shall be maintained as
overlays.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The EValuation Module(EVM) platform for AM654 consists of a
common Base board + one or more of daughter cards, which include:
a) "Personality Modules", which can be specific to a profile, such as
ICSSG enabled or Multi-media (including audio).
b) SERDES modules, which may be 2 lane PCIe or two port PCIe + USB2
c) Camera daughter card
d) various display panels
Among other options. There are two basic configurations defined which
include an "EVM" configuration and "IDK" (Industrial development kit)
which differ in the specific combination of daughter cards that are
used.
To simplify support, we choose to support just the base board as the
core device tree file and all daughter cards would be expected to be
device tree overlays.
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
