Configure timer nodes on stm32mp257f-ev1:
- Timer3 CH2 is available on mikroBUS connector for PWM
- timer8 CH1, timer8 CH4, timer10 CH1 and timer12 CH2 are available
on EXPANSION connector.
Timers are kept disabled by default, so the pins can be used for any
other purpose (and the timers can be assigned to any of the processors).
Arbitrary choice is to use all these timers as PWM (or counter on
internal clock signal), except for timer10 that is configured with
CH1 as an input (for capture).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20250110091922.980627-9-fabrice.gasnier@foss.st.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
During the low power modes the generic ARM timer is deactivated, so the
the tick broadcast is used, based on LPTIMER3 which is clocked by LSE on
STMicroelectronics boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Enable the camera pipeline with a imx335 sensor connected to the
dcmipp via the csi interface.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Enable the COMBOPHY with external pad clock on stm32mp257f-ev1
board, to be used for the PCIe clock provider.
Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add dmas and dma-names properties in u(s)art nodes of stm32mp251.dtsi to
enable DMA support.
RX channel requires to prevent pack/unpack feature of DMA to avoid losing
bytes when interrupting RX transfer, as it uses a cyclic buffer.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
ETHERNET2 instance is connected to Realtek PHY in RGMII mode
Ethernet is SNSP IP with GMAC5 version.
Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add properties for spi3 and spi8 available on the stm32mp257f-ev1.
Both are kept disabled since only used via the gpio expansion connector.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add properties for i2c2 and i2c8 available on the stm32mp257f-ev1.
i2c2 is enabled since several devices are attached to it while
i2c8 is kept disabled since only used via the gpio expansion connector.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Enable the watchdog and define the default timeout to 32 seconds.
Signed-off-by: Lionel Debieve <lionel.debieve@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add the configuration node for SD-card support on STM32MP257F-EV1 board.
For the moment it uses a fixed regulator for vmmc, and vqmmc is skipped
until regulator driver is available.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add STM32MP257F Evaluation board support. It embeds a STM32MP257FAI SoC,
with 4GB of DDR4, TSN switch (2+1 ports), 2*USB typeA, 1*USB2 typeC,
SNOR OctoSPI, mini PCIe, STPMIC2 for power distribution ...
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
