Add ahci core controller and glue layer nodes including reset-controller
and sata-phy.
This supports for PXs3 and the boards.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042321.4817-7-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use human-readable definitions for GIC interrupt type and flag, instead of
hard-coding the numbers. No functional change.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042321.4817-6-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
According to gpio-hog schema, should add the suffix "-hog" to the node
names including gpio-hog to fix the following warning.
uniphier-ld11-ref.dtb: gpio@55000000: 'xirq0' does not match any of the regexes: '^.+-hog(-[0-9+)?$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/gpio/socionext,uniphier-gpio.yaml
This applies to the devicetre for LD11, LD20 and PXs3 SoCs.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042321.4817-5-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This renames the node name "ethphy" to "ethernet-phy" according to
Documentation/devicetree/bindings/net/mdio.yaml.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit e69f5dc623 ("dt-bindings: serial: Convert 8250 to
json-schema"), the schema for "ns16550a" is checked.
Since then, 'make ARCH=arm64 dtbs_check' is so noisy because the
required property 'interrupts' is missing.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The RGMII PHY implemented in PXs3 ref board needs to change
drive-strength properties of the Ethernet Tx pins to stabilize the PHY.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add 'aliases' properties for ethernet device.
U-Boot performs a fix-up of the MAC address and will overwrite the values
from the Linux devicetree for aliased ethernet device. The MAC address can
be inherited from U-Boot by adding aliases of ethernet devices.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
PXs3 reference board has 2 spi connectors. This enables spi0 and spi1,
and adds aliases properties for each spi to determine device name
assignments.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
With commit d8e8fd0ebf ("mtd: rawnand: denali: decouple controller
and NAND chips"), the Denali NAND controller driver migrated to the
new controller/chip representation.
Update DT for it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Sort the labels in the same order as in the corresponding dtsi file,
in other words, the order of reg address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add USB3 controller nodes including usb-core, resets, regulator, ss-phy
and hs-phy. This supports for LD20, PXs3 and the boards. This includes
additional efuse nodes for obtaining PHY trimming values.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add SD controller nodes for LD20 and PXs3.
LD20 does not support the UHS mode, while PXs3 supports it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add nodes of the AVE ethernet controller for PXs3 and the boards.
This SoC has two controllers.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
According to Documentation/process/license-rules.rst, move the SPDX
License Identifier to the very top of the file. I used C++ comment
style not only for the SPDX line but for the entire block because
this seems Linus' preference [1]. I also dropped the parentheses to
follow the examples in that document.
[1] https://lkml.org/lkml/2017/11/25/133
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The serial pins of PXs3 SoC are not multiplexed with any other
functions. Enable serial2 and serial3 on the PXs3 reference board
because I see the connectors on the board.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 15e85695e5 ("arm64: dts: uniphier: add GPIO hog definition")
missed to update the PXs3 DTS for some reason. Do it now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These were added to make the ARM64 branch self-contained because
updates for ARM and ARM64 are supposed to be sent as separate
pull requests.
Now, they were merged together in Linus' tree and interrupt-parent
from the arch/arm/boot/dts/uniphier-support-card.dtsi is visible from
ARM64 DT files by the cross-arch reference.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 429f203eb7 ("arm64: dts: uniphier: route on-board device IRQ
to GPIO controller") missed to update this DTS. It becames a real
problem when arm and arm64 trees are merged together.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
