Enabling the GPU power domain requires that the GPU regulator is
enabled. The regulator is enabled at boot time, but gets disabled
automatically when there are no users.
This means the system might run into a failure state hanging the
whole system for the following use cases:
* if the GPU driver is being probed late (e.g. build as a
module and firmware is not in initramfs), the regulator
might already have been disabled. In that case the power
domain is enabled before the regulator.
* unbinding the GPU driver will disable the PM domain and
the regulator. When the driver is bound again, the PM
domain will be enabled before the regulator and error
appears.
Avoid this by adding an explicit regulator dependency to the
power domain.
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reported-by: Adrián Martínez Larumbe <adrian.larumbe@collabora.com>
Tested-by: Adrian Larumbe <adrian.larumbe@collabora.com> # On Rock 5B
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20250220-rk3588-gpu-pwr-domain-regulator-v6-8-a4f9c24e5b81@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The hdptxphy is a combo transmit-PHY for HDMI2.1 TMDS Link, FRL Link, DP
and eDP Link. Therefore, it is better to name it hdptxphy0 other than
hdptxphy_hdmi0, which will be referenced by both hdmi0 and edp0 nodes.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Link: https://lore.kernel.org/r/20250206030330.680424-3-damon.ding@rock-chips.com
[added armsom-sige7, where hdmi-support was added recently and also
the hdptxphy0-as-dclk source I just added]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The preferred nodename for fixed-regulators has changed to
pattern: '^regulator(-[0-9]+v[0-9]+|-[0-9a-z-]+)?$'
Fix all Rockchip DT regulator nodenames.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/0ae40493-93e9-40cd-9ca9-990ae064f21a@gmail.com
[adapted rebased on top of a number of other changes and included
neu6a-wifi + wolfvision-pf5-io-expander overlays]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
These pinctrls manage the low-speed PCIe signals:
- CLKREQ#: An output on the RK3588 (both RC or EP modes), used to
request that external clock-generation circuitry provide a clock.
- PERST#: An input on the RK3588 in EP mode, used to detect a reset
signal from the RC. In RC mode, the hardware does not use this signal:
Linux itself generates it by putting the pin in GPIO mode.
- WAKE#: In EP mode, this is an output; in RC mode, this is an input.
Each of these signals serves a distinct purpose, and more importantly,
PERST# should not be muxed when the RK3588 is in the RC role. Bundling
them together in pinctrl groups prevents proper use: indeed, almost none
of the current board-specific .dts files make any use of them.
(Exception: Rock 5A recently had a patch land that misuses _pins; this
patch corrects that.)
However, on some RK3588 boards, the PCIe 3 controller will indefinitely
stall the boot if CLKREQ# is not muxed (details in the next patch).
This patch unbundles the signals to allow them to be used.
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Link: https://lore.kernel.org/r/20240912025034.180233-2-CFSworks@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable pcie2x1l2 and related combphy/regulator routed to M.2 E key
connector on Radxa ROCK 5A.
Tested with Radxa Wireless Module A8:
$ lspci
0004:40:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3588 (rev 01)
0004:41:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8852BE PCIe 802.11ax Wireless Network Controller
$ ip l
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: end0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether c2:58:fc:70:55:86 brd ff:ff:ff:ff:ff:ff
3: wlP4p65s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 2c:05:47:65:5b:ed brd ff:ff:ff:ff:ff:ff
$ lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 1a40:0101 Terminus Technology Inc. Hub
Bus 001 Device 003: ID 0bda:b85b Realtek Semiconductor Corp. Bluetooth Radio
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 006 Device 002: ID 0789:0336 Logitec Corp. LMD USB Device
Bus 007 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 008 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
$ hciconfig
hci0: Type: Primary Bus: USB
BD Address: 2C:05:47:65:5B:EE ACL MTU: 1021:6 SCO MTU: 255:12
UP RUNNING
RX bytes:2698 acl:0 sco:0 events:329 errors:0
TX bytes:69393 acl:0 sco:0 commands:329 errors:0
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20240826080456.525-1-naoki@radxa.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There is no "on-board WLAN/BT chip" on Radxa ROCK 5A. remove related
properties.
Fixes: 1642bf66e2 ("arm64: dts: rockchip: add USB2 to rk3588s-rock5a")
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20240826075130.546-1-naoki@radxa.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The devicetree updates are fairly well spread out across platforms,
with Qualcomm making up about a third of the total.
There are three new SoCs in existing product families this:
- NXP i.MX95 is a variant of i.MX93, now with six Cortex-A55 cores
instead of just two as well as a GPU and more high-speed I/O
devices.
- Qualcomm QCS8550 is a variant of SM8550 for IOT devices
- Airoha EN7581 is a 10G-PON network chip and related to
the MT7981 Wireless router chip from its parent Mediatek.
In total there are 58 new machines, including four riscv
boards and eight for 32-bit arm.
The most exciting new addition is probably a pair of laptops
based on the Qualcomm x1e80100 (Snapdragon X1 Elite) chip,
the Asus Vivobook S15 and the Lenovo Yoga Slim7x.
Other noteworthy new additions are:
- A total of 20 Qualcomm based machines, mostly Android devices
from Samsung, Motorola and LG, as well as a wireless router
and some reference designs
- Six NXP i.MX based machines, mostly industrial boards along
with some reference designs
- Mediatek sees some interesting Filogic based routers
including the "OpenWRT One", a few new Chromebooks as
well as single-board computers.
- Four machines from Solidrun based on Marvell cn913x,
replacing the older Armada 8000 based counterparts
- The four Amlogic machines are all set top boxes or reference
designs for them
- The nine new Rockchips machines are mostly single-board
computers including some interesting ones based on the
rk3588 chip like the ROCK 5 ITX board and the CM3588
with its four NVMe slots
- The RISC-V boards are all single-board computers based on
Starfive JH7110, Microchip MPFS and Allwinner D1, which all
had similar boards already
There are also a lot of updates to already supported machines,
notably for the TI K3, Rockchips, Freescale and of course
Qualcomm platforms.
-----BEGIN PGP SIGNATURE-----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=xGqj
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC dt updates from Arnd Bergmann:
"The devicetree updates are fairly well spread out across platforms,
with Qualcomm making up about a third of the total.
There are three new SoCs in existing product families this:
- NXP i.MX95 is a variant of i.MX93, now with six Cortex-A55 cores
instead of just two as well as a GPU and more high-speed I/O
devices.
- Qualcomm QCS8550 is a variant of SM8550 for IOT devices
- Airoha EN7581 is a 10G-PON network chip and related to the MT7981
Wireless router chip from its parent Mediatek.
In total there are 58 new machines, including four riscv boards and
eight for 32-bit arm.
The most exciting new addition is probably a pair of laptops based on
the Qualcomm x1e80100 (Snapdragon X1 Elite) chip, the Asus Vivobook
S15 and the Lenovo Yoga Slim7x.
Other noteworthy new additions are:
- A total of 20 Qualcomm based machines, mostly Android devices from
Samsung, Motorola and LG, as well as a wireless router and some
reference designs
- Six NXP i.MX based machines, mostly industrial boards along with
some reference designs
- Mediatek sees some interesting Filogic based routers including the
"OpenWRT One", a few new Chromebooks as well as single-board
computers.
- Four machines from Solidrun based on Marvell cn913x, replacing the
older Armada 8000 based counterparts
- The four Amlogic machines are all set top boxes or reference
designs for them
- The nine new Rockchips machines are mostly single-board computers
including some interesting ones based on the rk3588 chip like the
ROCK 5 ITX board and the CM3588 with its four NVMe slots
- The RISC-V boards are all single-board computers based on Starfive
JH7110, Microchip MPFS and Allwinner D1, which all had similar
boards already
There are also a lot of updates to already supported machines, notably
for the TI K3, Rockchips, Freescale and of course Qualcomm platforms"
* tag 'soc-dt-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (846 commits)
arm64: dts: allwinner: h616: add crypto engine node
riscv: dts: add clock generator for Sophgo SG2042 SoC
arm64: dts: rockchip: Add Xunlong Orange Pi 3B
dt-bindings: arm: rockchip: Add Xunlong Orange Pi 3B
arm64: dts: rockchip: Add Radxa ROCK 3B
dt-bindings: arm: rockchip: Add Radxa ROCK 3B
mailmap: Update Luca Weiss's email address
ARM: dts: ixp4xx: nslu2: beeper uses PWM
arm64: dts: rockchip: add ROCK 5 ITX board
dt-bindings: arm: rockchip: Add ROCK 5 ITX board
arm64: dts: rockchip: Add dma-names to uart1 on Pine64 rk3566 devices
arm64: dts: rockchip: Add avdd supplies to hdmi on rock64
arm64: dts: qcom: msm8916-lg-c50: add initial dts for LG Leon LTE
arm64: dts: qcom: msm8916-lg-m216: Add initial device tree
dt-bindings: arm: qcom: Add msm8916 based LG devices
ARM: dts: qcom: msm8960: correct memory base
arm64: dts: qcom: ipq9574: Add icc provider ability to gcc
dt-bindings: interconnect: Add Qualcomm IPQ9574 support
arm64: dts: qcom: sm8150: Add video clock controller node
arm64: dts: qcom: pm6150: Add vibrator
...
This commit adds SFC node for Radxa ROCK 5A.
since sdhci and sfc on RK3588s share pins(i.e. exclusive), it cannot
be enabled both nodes at the same time. so status = "okay" is omitted
here.
you may be able to enable sfc (and disable sdhci) by fdt overlay.
SPI NOR flash chip may vary, so use safe(lowest) spi-max-frequency.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20240623023329.1044-2-naoki@radxa.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This enables the on-chip thermal monitoring sensor (TSADC) on all
RK3588(s) boards that don't have it enabled yet. It provides temperature
monitoring for the SoC and emergency thermal shutdowns, and is thus
important to have in place before CPU DVFS is enabled, as high CPU
operating performance points can overheat the chip quickly in the
absence of thermal management.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Link: https://lore.kernel.org/r/20240617-rk-dts-additions-v5-2-c1f5f3267f1e@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Designate the RK806 PMIC on the Radxa ROCK 5A as the system power
controller, so the board shuts down properly on poweroff(8).
Fixes: 75fdcbc8f4 ("arm64: dts: rockchip: add PMIC to rock-5a")
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20240612033523.37166-1-naoki@radxa.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
gpio_pwrctrl2 gets duplicated by both rk806_dvs1_null and rk806_dvs2_null
gpio_pwrctrl1 is unset. This typo appears in multiple files. Let's fix them.
Note: I haven't had the chance to test them all because I don't own all
of these boards (obviously). Please test if it's needed.
Signed-off-by: Jing Luo <jing@jing.rocks>
Link: https://lore.kernel.org/r/20240420130355.639406-1-jing@jing.rocks
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable full support (XHCI, EHCI, OHCI) for the upper USB3 port from
Radxa Rock 5 Model A. The lower one is already supported.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20240408225109.128953-10-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The sdmmc node already have a "&sdmmc_det" for pinctrl which switch the
GPIO0A4 to sdmmc detect function, no need to define a separate "cd-gpios".
RK3588 has force_jtage feature which is enable JTAG function via sdmmc
pins automatically when there is no SD card insert, this feature will
need the GPIO0A4 works in sdmmc_det function like other mmc signal instead
of GPIO function, or else the force_jtag can not auto be disabled when
SD card insert.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Link: https://lore.kernel.org/r/20240201034621.1970279-1-kever.yang@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The serial ports on rk3588 are named uart0 - uart9. Board schematics
also use these exact numbers and we want those names to also reflect
in the OS devices because everything else would just cause confusion.
To prevent each board repeating their list of serial aliases, move them
to the soc dtsi, as all previous Rockchip soc do already.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20231205164842.556684-2-heiko@sntech.de
Enable USB3 host controller for the Radxa ROCK 5 Model A. This adds
USB3 for the lower USB3 port (the one closer to the PCB).
The upper USB3 port uses the RK3588 USB TypeC host controller, which
use a different PHY without upstream support.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20231106155934.80838-2-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable USB2 (EHCI and OCHI mode) support for the Radxa ROCK 5 Model A.
This adds USB support for the on-board WLAN/BT chip, the two USB2
ports, the USB available from the 2x20 connector and the lower USB3
port (in USB2 mode).
The upper USB3 (further away from the PCB) uses the RK3588S USB TypeC
OTG controller for USB2 and USB3 and thus is not supported at all at
the moment.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230712165106.65603-5-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
200MHz is the default rk3588 emmc max-frequency added in dtsi, so why
the board DT files are adding the same value explicitly?
Drop that unchanged property value.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230621064507.479891-1-jagan@edgeble.ai
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable ADC support for Rock 5A, which has the following ADC channels:
Channel 0 = Boot Mode Config
Channel 1 = Recovery Key
Channel 2 = PWM Fan
Channel 3 = Headphone Hook
Channel 4 = System Input Voltage
Channel 5 = Board ID Config
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-13-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
I2C3 is routed to the Camera connector and I2C5 is routed to the LCD
connector. On I2C5 additionally there is an unpopulated footprint for
a HYM8563TS RTC.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-12-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add analog audio support based on the Everest Semi ES8316 codec.
Note, that this currently does not support headphone plug events. The
Rock 5A uses a different headphone jack with a different logic to detect
a headphone plug. Unfortunately the detect GPIO is always low.
Downstream uses an ADC channel instead, but that is currently not
supported upstream.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-9-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The RK8602 and RK8603 voltage regulators on the Rock 5A board provide
the power lines vdd_cpu_big0 and vdd_cpu_big1, respectively.
Add the necessary device tree nodes and bind them to the corresponding
CPU big core nodes.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-5-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds PMIC support for the Radxa ROCK 5A
Co-developed-by: shengfei Xu <xsf@rock-chips.com>
Signed-off-by: shengfei Xu <xsf@rock-chips.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-4-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add network PHY rx delay and change type to rgmii, so
that it is applied. This fixes packet loss when more
than a few packets are exchanged.
Fixes: d1824cf957 ("arm64: dts: rockchip: Add rock-5a board")
Signed-off-by: Lucas Tanure <lucas.tanure@collabora.com>
Link: https://lore.kernel.org/r/20230113130220.662194-1-lucas.tanure@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
In the previous version, the sdhci alias was set to mmc1: an artifact
leftover from the port from vendor kernel. Update the alias to mmc0 to
match the device's boot order.
Fixes: a4a8f1afb360 ("arm64: dts: rockchip: Add rock-5a board")
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Link: https://lore.kernel.org/r/20230110195352.272360-2-chris.obbard@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add board file for the RK3588s Rock 5A board. While the hardware
offers plenty of peripherals and connectivity this basic implementation
just handles things required to access eMMC, UART and Ethernet (i.e.
enough to successfully boot Linux).
Reviewed-by: Michael Riesch <michael.riesch@wolfvision.net>
Tested-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230109155801.51642-7-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
