cd-gpios is used for sdcard detects for sdmmc.
Fixes: 3f5d336d64 ("arm64: dts: rockchip: Add support for rk3588s based board Cool Pi 4B")
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://lore.kernel.org/r/20250524064223.5741-2-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
These Rockchip boards assign "active" as the pinctrl name for PWM
controllers, which has never been supported in mainline Rockchip PWM
driver. It seems the name used by downstream kernel is accidentally
brought into maineline. Let's fix them.
Fixes: 4403e1237b ("arm64: dts: rockchip: Add devicetree for board roc-rk3308-cc")
Fixes: 964ed0807b ("arm64: dts: rockchip: add rk3318 A95X Z2 board")
Fixes: e7a0959082 ("arm64: dts: rockchip: Add devicetree for NanoPC-T4")
Fixes: 3f5d336d64 ("arm64: dts: rockchip: Add support for rk3588s based board Cool Pi 4B")
Signed-off-by: Yao Zi <ziyao@disroot.org>
Link: https://lore.kernel.org/r/20250310140916.14384-2-ziyao@disroot.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enabling the GPU power domain requires that the GPU regulator is
enabled. The regulator is enabled at boot time, but gets disabled
automatically when there are no users.
This means the system might run into a failure state hanging the
whole system for the following use cases:
* if the GPU driver is being probed late (e.g. build as a
module and firmware is not in initramfs), the regulator
might already have been disabled. In that case the power
domain is enabled before the regulator.
* unbinding the GPU driver will disable the PM domain and
the regulator. When the driver is bound again, the PM
domain will be enabled before the regulator and error
appears.
Avoid this by adding an explicit regulator dependency to the
power domain.
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reported-by: Adrián Martínez Larumbe <adrian.larumbe@collabora.com>
Tested-by: Adrian Larumbe <adrian.larumbe@collabora.com> # On Rock 5B
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20250220-rk3588-gpu-pwr-domain-regulator-v6-8-a4f9c24e5b81@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable USB3 OTG and it's related PHY node. And the PHY will
also be shared with the upcoming DisplayPort controller.
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://lore.kernel.org/r/20250223100757.73531-1-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The hdptxphy is a combo transmit-PHY for HDMI2.1 TMDS Link, FRL Link, DP
and eDP Link. Therefore, it is better to name it hdptxphy0 other than
hdptxphy_hdmi0, which will be referenced by both hdmi0 and edp0 nodes.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Link: https://lore.kernel.org/r/20250206030330.680424-3-damon.ding@rock-chips.com
[added armsom-sige7, where hdmi-support was added recently and also
the hdptxphy0-as-dclk source I just added]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The preferred nodename for fixed-regulators has changed to
pattern: '^regulator(-[0-9]+v[0-9]+|-[0-9a-z-]+)?$'
Fix all Rockchip DT regulator nodenames.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/0ae40493-93e9-40cd-9ca9-990ae064f21a@gmail.com
[adapted rebased on top of a number of other changes and included
neu6a-wifi + wolfvision-pf5-io-expander overlays]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
According to the hardware design, the i2c address of audio codec es8316
on Cool Pi 4B is 0x10.
This fix the read/write error like bellow:
es8316 7-0011: ASoC: error at soc_component_write_no_lock on es8316.7-0011 for register: [0x0000000c] -6
es8316 7-0011: ASoC: error at soc_component_write_no_lock on es8316.7-0011 for register: [0x00000003] -6
es8316 7-0011: ASoC: error at soc_component_read_no_lock on es8316.7-0011 for register: [0x00000016] -6
es8316 7-0011: ASoC: error at soc_component_read_no_lock on es8316.7-0011 for register: [0x00000016] -6
Fixes: 3f5d336d64 ("arm64: dts: rockchip: Add support for rk3588s based board Cool Pi 4B")
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://lore.kernel.org/r/20240623115526.2154645-1-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
gpio_pwrctrl2 gets duplicated by both rk806_dvs1_null and rk806_dvs2_null
gpio_pwrctrl1 is unset. This typo appears in multiple files. Let's fix them.
Note: I haven't had the chance to test them all because I don't own all
of these boards (obviously). Please test if it's needed.
Signed-off-by: Jing Luo <jing@jing.rocks>
Link: https://lore.kernel.org/r/20240420130355.639406-1-jing@jing.rocks
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Follow others rk3588 based boards, and u-boot only use mmc0/1
as mmc boot targets, so aliase sdmmc as mmc1.
Fixes: 3f5d336d64 ("arm64: dts: rockchip: Add support for rk3588s based board Cool Pi 4B")
Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20240201121106.1471301-1-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
CoolPi 4B is a rk3588s based SBC.
Specification:
- Rockchip RK3588S
- LPDDR4 2/4/8/16 GB
- TF scard slot
- eMMC 8/32/64/128 GB module
- Gigabit ethernet drived by PCIE with RTL8111HS
- HDMI Type D out
- Mini DP out
- USB 2.0 Host x 2
- USB 3.0 OTG x 1
- USB 3.0 Host x 1
- WIFI/BT module AIC8800
- 40 pin header
Signed-off-by: Andy Yan <andyshrk@163.com>
arm64: dts: rockchip: Add support for rk3588s based board Cool Pi 4B
Link: https://lore.kernel.org/r/20231212124253.1897438-1-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
