The #address-cells and #size-cells properties are not useful on the DSI
controller node; they are only useful/required on ports and panel(s).
So remove them from the controller node and add them where actually
needed on the various rk3399 based boards.
This fixes the following DTB validation warnings:
unnecessary #address-cells/#size-cells without "ranges",
"dma-ranges" or child "reg" property
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
Link: https://lore.kernel.org/r/20250709132323.128757-3-didi.debian@cknow.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the description of the front/user camera (OV8858) on the PinePhone Pro
to the device dts file.
It receives commands over SCCB, an I2C-compatible protocol, at
I2C address 0x36 and transmits data over CSI-MIPI.
I confirmed this address experimentally.
The pin control mapping was again extracted from the PinePhone Pro
schematic v1.0 as well as the RK3399 datasheet revision 1.8.
Table 2-3 in section 2.8 of the RK3399 datasheet contains the mapping
of IO functions for the SoC pins. Page 52 shows GPIO1_A4, page 54 shows
GPIO2_B4.
For the reset (RESET) signal:
page 11 quadrant D2 | p.18 q.B3-4 | p.18 q.C2
RK3399_E.R28 -> GPIO1_A4 -> Camera2_RST -> MIPI_RST1 -> OV8858.12
For the powerdown (PWDN) signal:
page 9 quadrants D4-5 | p.18 q.B2
RK3399_L.F31 -> GPIO2_B4 -> DVP_PDN0_H -> OV8858.14
Helped-by: Dragan Simic <dsimic@manjaro.org>
Co-developed-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Olivier Benjamin <olivier.benjamin@bootlin.com>
Link: https://lore.kernel.org/r/20250620-camera-v4-4-0201a8ed5fae@bootlin.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the description of the rear/world camera (IMX258) on the PinePhone Pro
to the device dts file.
It receives commands on the I2C Bus 1 at address 0x1a and transmits data
over CSI-MIPI.
The I2C address for IMX258 can be found in the IMX258-0AQH5 Software
Reference Manual, page 24, section 2.3.1: 0b0011010 = 0x1a.
Section 3 indicates the module has 4 pairs of data lines. While 4-lane
mode is nominal, 2-lane mode should also be supported.
The pin muxing info was extracted from the PinePhone Pro schematic v1.0
as well as the RK3399 datasheet revision 1.8.
Table 2-3 in section 2.8 of the RK3399 datasheet contains the mapping
of IO functions for the SoC pins. Page 52 shows GPIO1_A0, page 54 shows
GPIO2_D4.
For I2C power, the PinePhone Pro schematic page 11 quadrants A4 and A5:
RK3399_J.AA8 and RK3399_J.Y8 get power from vcaa1v8_codec, so turn it on
The IMX258 also uses the following regulators, expected by its driver:
- vana (2.8V analog), called AVDD2V8_DVP on P.18 q.C1 and derived from
VCC1V8_S3 on P.13 q.B2
- vdig (1.2V digital core), called DVDD_DVP on P.18 q.C1 and shown on
P.18 q.D3 to be equivalent to VCC1V2_DVP derived from VCC3V3_SYS on
P.13 q.B3. Note that this regulator's voltage is inconsistently
labeled either 1.2V or 1.5V
RK3399_J.AG1 is GPIO4_A1/I2C1_SDA, RK3399_J.Y6 is GPIO4_A2/I2C1_SCL
This is the default pinctrl "i2c1_xfer" for i2c1 from rk3399-base.
For the reset (RESET) signal:
page 11 quadrant D2 | p.18 q.C3-4 | p.18 q.C2
RK3399_E.R25 -> GPIO1_A0 -> Camera_RST -> MIPI_RST0 -> IMX258.12
For the powerdown (PWDN) signal:
page 11 quadrants B4-5 | p.18 q.C2
RK3399_G.AF8 -> GPIO2_D4 -> DVP_PDN1_H -> IMX258.14
Helped-by: Dragan Simic <dsimic@manjaro.org>
Co-developed-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Olivier Benjamin <olivier.benjamin@bootlin.com>
Link: https://lore.kernel.org/r/20250620-camera-v4-3-0201a8ed5fae@bootlin.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Fix a few issues in the panel section of the PinePhone Pro DTS:
- add the second part of the Himax HX8394 LCD panel controller
compatible
- as proposed by Diederik de Haas, reuse the mipi_out and ports
definitions from rk3399-base.dtsi instead of redefining them
- add a pinctrl for the LCD_RST signal for LCD1, derived from
LCD1_RST, which is on GPIO4_D1, as documented on pages 11
and 16 of the PinePhone Pro schematic
Signed-off-by: Olivier Benjamin <olivier.benjamin@bootlin.com>
Reviewed-by: Diederik de Haas <didi.debian@cknow.org>
Link: https://lore.kernel.org/r/20250619-dtb_fixes-v3-1-9cb02ddd8ce4@bootlin.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This release adds the devicetree files for an impressive number of new
SoC variants, though as expected these are all related to others we
already support:
- The microchip sam9x7 devicetree is now added, after the device driver
and platform code has already made it in. This is likely the last ARMv5
(!) platform to ever get added, updating the 20+ year old at91/sam9
platform wtih DDR3 memory and gigabit ethernet.
- On the Apple platform, there are now devicetree files for a number of
A-series SoCs in addition to the M-series ones, these are used
primarily in phones and tablets, but are closely related to the
already supported chips.
- Samsung Exynos 8895 and Exynos 990 are more phone SoCs used in older
Samsung Galaxy phones.
- Qualcomm Snapdragon 778G (SM7325) is another phone SoC, closely related
to the Snapdragon 7c+ Gen 3 (SC7280) used in low-end laptops.
- Rockchip RK3528 and RK3576 are new variants of their TV box and Tablet
chips, still using the older ARMv8.0 cores from RK3328/RK3399 but
with a newer process and other improvements from the RK35xx (otherwise
ARMv8.2) chips. RK3566T and RK3399-S are also added, these are just
lower-cost versions of their normal counterparts.
- TI J742S2 is a feature-reduced version of the J784s4
industrial/automotive SoC, with fewer CPU cores.
- Sophgo SG2002 is an embedded SoC with one RISC-V (C906) and one ARM
(Cortex-A53) core, at this point support is only added for running
on the RISC-V side on the LicheeRV Nano board.
A total of 92 new .dts files describing individual machines is added,
which must be a new record. The majority of these is for the newly added
chips above, notably all the Apple phones and tablets. The other new
machines include nine industrial/embedded boards with NXP i.MX6 or i.MX8
SoCs, eight for Rockchips RK35XX and one or two each for Rockchips RV1109,
RK3308, Allwinner A33, Tegra 234, Qualcomm qcs9100/sc8280xp/x1e80100,
TI AM625 and Starfive JH7110.
As usual there are also many newlyad added features in existing boards
as well as cleanups and minor bugfixes.
-----BEGIN PGP SIGNATURE-----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=Ha1w
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC devicetree updates from Arnd Bergmann:
"This release adds the devicetree files for an impressive number of new
SoC variants, though as expected these are all related to others we
already support:
- The microchip sam9x7 devicetree is now added, after the device
driver and platform code has already made it in. This is likely the
last ARMv5 (!) platform to ever get added, updating the 20+ year
old at91/sam9 platform with DDR3 memory and gigabit ethernet.
- On the Apple platform, there are now devicetree files for a number
of A-series SoCs in addition to the M-series ones, these are used
primarily in phones and tablets, but are closely related to the
already supported chips.
- Samsung Exynos 8895 and Exynos 990 are more phone SoCs used in
older Samsung Galaxy phones.
- Qualcomm Snapdragon 778G (SM7325) is another phone SoC, closely
related to the Snapdragon 7c+ Gen 3 (SC7280) used in low-end
laptops.
- Rockchip RK3528 and RK3576 are new variants of their TV box and
Tablet chips, still using the older ARMv8.0 cores from
RK3328/RK3399 but with a newer process and other improvements from
the RK35xx (otherwise ARMv8.2) chips. RK3566T and RK3399-S are also
added, these are just lower-cost versions of their normal
counterparts.
- TI J742S2 is a feature-reduced version of the J784s4
industrial/automotive SoC, with fewer CPU cores.
- Sophgo SG2002 is an embedded SoC with one RISC-V (C906) and one ARM
(Cortex-A53) core, at this point support is only added for running
on the RISC-V side on the LicheeRV Nano board.
A total of 92 new .dts files describing individual machines is added,
which must be a new record. The majority of these is for the newly
added chips above, notably all the Apple phones and tablets. The other
new machines include nine industrial/embedded boards with NXP i.MX6 or
i.MX8 SoCs, eight for Rockchips RK35XX and one or two each for
Rockchips RV1109, RK3308, Allwinner A33, Tegra 234, Qualcomm
qcs9100/sc8280xp/x1e80100, TI AM625 and Starfive JH7110.
As usual there are also many newly added features in existing boards
as well as cleanups and minor bugfixes"
* tag 'soc-dt-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (718 commits)
arm64: dts: apm: Remove unused and undocumented "bus_num" property
arm: dts: spear13xx: Remove unused and undocumented "pl022,slave-tx-disable" property
arm64: dts: amd: Remove unused and undocumented "amd,zlib-support" property
arm64: dts: lg131x: Update spi clock properties
arm64: dts: seattle: Update spi clock properties
arm64: dts: rockchip: use less broad pinctrl for pcie3x1 on Radxa E25
arm64: dts: rockchip: add Radxa ROCK 5C
dt-bindings: arm: rockchip: add Radxa ROCK 5C
arm64: dts: rockchip: orangepi-5-plus: Enable GPU
arm64: dts: rockchip: enable USB3 on NanoPC-T6
arm64: dts: rockchip: adapt regulator nodenames to preferred form
arm64: dts: rockchip: Enable HDMI display for rk3588 Cool Pi GenBook
arm64: dts: rockchip: Enable HDMI display for rk3588 Cool Pi 4B
arm64: dts: rockchip: Enable HDMI0 for rk3588 Cool Pi CM5 EVB
arm64: dts: rockchip: Enable HDMI on NanoPi R6C/R6S
arm64: dts: rockchip: Enable GPU on NanoPi R6C/R6S
arm64: dts: rockchip: Enable HDMI on Hardkernel ODROID-M2
arm64: dts: rockchip: Remove non-removable flag from sdmmc on rk3576-sige5
arm64: dts: allwinner: a100: perf1: Add eMMC and MMC node
arm64: dts: allwinner: pinephone: Add mount matrix to accelerometer
...
The preferred nodename for fixed-regulators has changed to
pattern: '^regulator(-[0-9]+v[0-9]+|-[0-9a-z-]+)?$'
Fix all Rockchip DT regulator nodenames.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/0ae40493-93e9-40cd-9ca9-990ae064f21a@gmail.com
[adapted rebased on top of a number of other changes and included
neu6a-wifi + wolfvision-pf5-io-expander overlays]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The patch adding display support for the pinephone pro introduced two
regulators that contain pinctrl-names props but no pinctrl-assignments.
Looks like someone forgot the pinctrl settings, so remove the orphans
for now, until that changes.
Fixes: 3e987e1f22 ("arm64: dts: rockchip: Add internal display support to rk3399-pinephone-pro")
Cc: Martijn Braam <martijn@brixit.nl>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Ondrej Jirman <megi@xff.cz>
Reviewed-by: Ondrej Jirman <megi@xff.cz>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241008203940.2573684-11-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Following the hierarchical representation of the SoC data that's been already
established in the commit 296602b8e5 ("arm64: dts: rockchip: Move RK3399
OPPs to dtsi files for SoC variants"), add new SoC dtsi file for the Rockchip
RK3399S SoC, which is yet another variant of the Rockchip RK3399 SoC.
The only perceivable differences between the RK3399S and the RK3399 are in
the supported CPU DVFS OPPs, which result from the RK3399S being binned for
lower maximum CPU frequencies than the regular RK3399 variant.
The RK3399S variant is used in the Pine64 PinePhone Pro only, [1] whose board
dts file included the necessary adjustments to the CPU DVFS OPPs. This commit
effectively moves those adjustments into the separate RK3399S SoC dtsi file,
following the above-mentioned "encapsulation" approach.
No functional changes are introduced, which was validated by decompiling and
comparing the affected dtb file before and after these changes.
[1] https://wiki.pine64.org/index.php/PinePhone_Pro
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/c32622e4a6897378d9df81c8c3eda1bdb9211e0b.1728632052.git.dsimic@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Property 'rockchip,system-power-controller' was deprecated in commit
961748bb15 ("dt-bindings: mfd: rk8xx: Deprecate rockchip,system-power-controller")
in the "rockchip,rk{805,808,809,817,818}.yaml" mtd bindings and its
replacement is (just) 'system-power-controller'.
Update the rk3399 DT files which still used the deprecated variant.
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20241008105450.20648-5-didi.debian@cknow.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rename the Rockchip RK3399 SoC dtsi files and, consequently, adjust their
contents and the contents of the affected board dts(i) files appropriately,
to "encapsulate" the different CPU and GPU OPPs for each of the supported
RK3399 SoC variants into the respective SoC variant dtsi files.
Moving the OPPs to the SoC variant dtsi files, instead of requiring the
board dts(i) files to include both the SoC variant dtsi file and the right
OPP variant dtsi file, reduces the possibility for mismatched inclusion and
improves the overall hierarchical representation of data.
These changes follow the approach used for the Rockchip RK3588 SoC variants,
which was introduced and described further in commit def88eb4d8 ("arm64:
dts: rockchip: Prepare RK3588 SoC dtsi files for per-variant OPPs"). Please
see that commit for a more detailed explanation.
No functional changes are introduced, which was validated by decompiling and
comparing all affected dtb files before and after these changes. In more
detail, all decompiled dtb files remain exactly the same, except the files
list below, which results from all of them stemming from the same base board
dtsi file (rk3399-rock-pi-4.dtsi), while all of them include one of the three
different RK3399 SoC variant dtsi files by themselves:
- rk3399-rock-4se.dtb
- rk3399-rock-pi-4a.dtb
- rk3399-rock-pi-4a-plus.dtb
- rk3399-rock-pi-4b.dtb
- rk3399-rock-pi-4b-plus.dtb
- rk3399-rock-pi-4c.dtb
When compared with the decompiled original dtb files, these dtb files have
some of their blocks shuffled around a bit and some of their phandles have
different values, as a result of the changes to the order in which the
building blocks from the parent dtsi files are included into them, but they
still effectively remain the same as the originals.
The only exception to the "include only a SoC variant dtsi" is found in
rk3399-evb.dts, which includes rk3399-base.dtsi instead of rk3399.dtsi.
This is intentional, because this board dts file doesn't enable the TSADC,
so including rk3399.dtsi would enable the SoC to go into higher OPPs with
no thermal throttling in place. Let's hope that people interested in this
board will fix this in the future.
As a side note, due to the nature of introduced changes, this commit is best
viewed using the --break-rewrites option for git-log(1).
Related-to: def88eb4d8 ("arm64: dts: rockchip: Prepare RK3588 SoC dtsi files for per-variant OPPs")
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/9417b5c5b64f9aceea64530a85a536169a3e7466.1721532747.git.dsimic@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The PinePhone Pro has a cluster of 3 single RGB GPIO LEDs.
Add the GPIO entries for the 3 red/green/blue LEDs and an
entry for the multi-color group to allow them to be used
as a combined RGB LED.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20240623165326.1273944-1-pbrobinson@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Correct the model names of a few Pine64 boards and devices, according
to their official names used on the Pine64 wiki. This ensures consistency
between the officially used names and the names in the source code.
Cc: Marek Kraus <gamiee@pine64.org>
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/06ce014a1dedff11a785fe523056b3b8ffdf21ee.1713832790.git.dsimic@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
These are implemented via regular ADC, so regular polling is needed,
for these keys to work.
Co-developed-by: Martijn Braam <martijn@brixit.nl>
Signed-off-by: Martijn Braam <martijn@brixit.nl>
Co-developed-by: Kamil Trzciński <ayufan@ayufan.eu>
Signed-off-by: Kamil Trzciński <ayufan@ayufan.eu>
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Ondrej Jirman <megi@xff.cz>
Link: https://lore.kernel.org/r/20230405123813.2272919-1-pbrobinson@gmail.com
[increased Volume-Down voltage to 600mV as suggested by Ondrej]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The phone has a Goodix GT1158 touchscreen, add a DT node for it.
Signed-off-by: Martijn Braam <martijn@brixit.nl>
Co-developed-by: Kamil Trzciński <ayufan@ayufan.eu>
Signed-off-by: Kamil Trzciński <ayufan@ayufan.eu>
Co-developed-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20230328073309.1743112-3-javierm@redhat.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The phone's display is using a Hannstar LCD panel. Support it by adding a
panel DT node and all needed nodes (backlight, MIPI DSI, regulators, etc).
Signed-off-by: Martijn Braam <martijn@brixit.nl>
Co-developed-by: Kamil Trzciński <ayufan@ayufan.eu>
Signed-off-by: Kamil Trzciński <ayufan@ayufan.eu>
Co-developed-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Ondrej Jirman <megi@xff.cz>
Link: https://lore.kernel.org/r/20230328073309.1743112-2-javierm@redhat.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
While this device uses the rk3399 it is also enclosed in a tight package
and cooled through the screen and back case. The default rk3399 thermal
limits can result in a burnt screen.
These lower limits have resulted in the existing burn not expanding and
will hopefully result in future devices not experiencing the issue.
Signed-off-by: Jarrah Gosbell <kernel@undef.tools>
Link: https://lore.kernel.org/r/20221207113212.8216-1-kernel@undef.tools
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pinephone Pro includes a AzureWave AW-CM256SM wifi (sdio0) and
bt (uart0) combo module, which is based on Cypress
CYP43455 (BCM43455).
The CYP43455 datasheet ("Power-Up Sequence and Timing") documents:
* needing to wait 10ms between consecutive WL_REG_ON toggles
* needing to wait 110ms between power-on and SDIO access.
Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Reviewed-by: Ondřej Jirman <megi@xff.cz>
Link: https://lore.kernel.org/r/20221002092809.451501-1-tom@tom-fitzhenry.me.uk
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Voltage constraints on vccio_sd are invalid. They don't match the voltages
that LDO9 can generate, and this causes rk808-regulator driver to fail
to probe with -EINVAL when it tries to apply the constraints during boot.
Fix the constraints to something that LDO9 can be actually configured for.
Fixes: 78a21c7d59 ("arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro")
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Reviewed-by: Caleb Connolly <kc@postmarketos.org>
Reviewed-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Tested-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Link: https://lore.kernel.org/r/20220904233652.3197885-1-megi@xff.cz
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This is a basic DT containing regulators and UART, intended to be a
base that myself and others can add additional nodes in future patches.
Tested to work: booting from eMMC/SD, output over UART.
https://wiki.pine64.org/wiki/PinePhone_Pro
This is derived from the community pine64-org repo[0] with fixes from
https://megous.com/git/linux.
0. 261d3b5f8a
Signed-off-by: Martijn Braam <martijn@brixit.nl>
Co-developed-by: Kamil Trzciński <ayufan@ayufan.eu>
[no SoB, but Kamil is happy for this patch to be submitted]
Co-developed-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Co-developed-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Reviewed-by: Caleb Connolly <kc@postmarketos.org>
Reviewed-by: Nícolas F. R. A. Prado <n@nfraprado.net>
Tested-by: Nícolas F. R. A. Prado <n@nfraprado.net>
Link: https://lore.kernel.org/r/20220829050040.17330-2-tom@tom-fitzhenry.me.uk
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
